PCI-6882 User Manual PCI Intel Pentium
PCI-6882
PCI Intel® Pentium® 4/Celeron®
D/Celeron® Half-sized SBC with
VGA/LVDS/LAN/USB2.0/TV-out/
SSD/SATA
User Manual
Copyright
This document is copyrighted, © 2006. All rights are reserved. The original manufacturer reserves the right to make improvements to the products
described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of
the original manufacturer. Information provided in this manual is
intended to be accurate and reliable. However, the original manufacturer
assumes no responsibility for its use, nor for any infringements upon the
rights of third parties that may result from such use.
Acknowledgements
Award is a trademark of Award Software International, Inc.
VIA is a trademark of VIA Technologies, Inc.
IBM, PC/AT, PS/2 and VGA are trademarks of International Business
Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows® is a registered trademark of Microsoft Corp.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
ESS is a trademark of ESS Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
SMI is a trademark of Silicon Motion, Inc.
Creative is a trademark of Creative Technology LTD.
All other product names or trademarks are properties of their respective
owners.
For more information on this and other Advantech products, please visit
our websites at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our support website at:
http://www.advantech.com/support
This manual is for the PCI-6882.
Part No.200K688210
1st Edition
Feb. 2006
PCI-6882 User Manual
ii
Packing List
Before you begin installing your card, please make sure that the following
materials have been shipped:
• 1 PCI-6882 Series Half-sized SBC
• 1 Startup manual
• 1 Utility disk/CD driver
• 1 Y cable for PS/2 Keyboard, PS/2 Mouse
p/n: 1700060202
• 1 EIDE (HDD) cable
p/n: 1701400452
• 1 FDD cable (600mm)
p/n: 1701340603
• 1 Printer port cable
p/n: 1700260250
• 1 Power cable
p/n: 1700000265
• Mini Jumper
p/n: 1653302122
If any of these items are missing or damaged, contact your distributor or
sales representative immediately.
Model No. List
Description
PCI-6882F-00A1
PCI Socket 478 Slot PC
w/LAN/VGA/LVDS/USB/TV-out/SATA
PCI-6882FG-00A1
Giga
bit Ethernet
Same as PCI-6882F-00A1 but with
PCI-6882L-00A1
SATA
Same as PCI-6882F-00A1, without
iii
Additional Information and Assistance
Visit the Advantech web site at www.advantech.com where you can find
the latest information about the product.
Step 1. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional
assistance. Please have the following information ready before
you call:
• Product name and serial number
• Description of your peripheral attachments
• Description of your software (operating system, version, application
software, etc.)
• A complete description of the problem
• The exact wording of any error messages
PCI-6882 User Manual
iv
FCC
This device complies with the requirements in
part 15 of the FCC rules: Operation is subject to
the following two conditions:
1.This device may not cause harmful interference, and
2. This device must accept any interference
received, including interference that may cause
undesired operation
This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment
is operated in a commercial environment. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this device in a residential
area is likely to cause harmful interference in
which case the user will be required to correct
the interference at his/her own expense. The
user is advised that any equipment changes or
modifications not expressly approved by the
party responsible for compliance would void the
compliance to FCC regulations and therefore,
the user's authority to operate the equipment.
Caution!
Achtung!
There is a danger of a new battery exploding if it
is incorrectly installed. Do not attempt to
recharge, force open, or heat the battery.
Replace the battery only with the same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer’s instructions.
v
PCI-6882 User Manual
vi
Contents
Chapter
1 General Information ........................................2
1.1
1.2
1.3
Introduction ....................................................................... 2
Features ............................................................................. 2
Specifications .................................................................... 3
1.3.1
1.3.2
1.3.3
1.3.4
1.3.5
1.3.6
1.4
Standard SBC Functions................................................. 3
Display Interface............................................................. 4
TV-out (optional)............................................................ 4
Solid State Disk .............................................................. 4
Ethernet Interface............................................................ 4
Mechanical and Environmental ...................................... 4
Board layout: dimensions............................................. 5
Figure 1.1:Board layout: dimensions (component side). 5
Figure 1.2:Board layout: dimensions (solder side)......... 5
Chapter
2 Installation ........................................................8
2.1
Jumpers.............................................................................. 8
2.2
Connectors......................................................................... 9
2.3
Locating Connectors ...................................................... 10
Table 2.1:Jumpers........................................................... 8
Table 2.2:Connectors ...................................................... 9
Figure 2.1:Jumper & Connector Locations (component
side)10
Figure 2.2:Connectors (solder side).............................. 10
2.4
2.5
Setting Jumpers ............................................................... 11
COM2 RS-232/422/485 Select (J2) ................................ 12
2.6
Clear CMOS (J1)............................................................. 12
2.7
LCD voltage setting (J3) ................................................. 13
2.8
SMBus Connector (J4) .................................................... 13
2.9
CPU FSB select Connector (JP1) ................................ 13
2.10
PCI VIO setting Connector (JP2) ................................ 13
2.11
2.12
2.13
2.14
Installing SODIMMs ................................................. 14
ATX power control Connector (CN21) .......................... 14
Printer port Connector (CN5).......................................... 14
CompactFlash Card Socket ............................................. 15
Table 2.3:COM2 RS-232/422/485 Select..................... 12
Table 2.4: Clear CMOS (J1) ....................................... 12
Table 2.5:LCD voltage setting (J3)............................... 13
Table 2.6:SMBus Connector (J4) ................................. 13
Table 2.7:CPU FSB select Connector (JP1) ................. 13
Table 2.8:PCI VIO setting Connector (JP2) ................. 13
2.14.1 CompactFlash (CN23) .................................................. 15
vii
2.15
Floppy drive Connector (CN2) ....................................... 15
2.15.1 Connecting the floppy drive ......................................... 15
2.16
IDE Connector (CN3,CN4)............................................. 16
2.16.1 Connecting the hard drive............................................. 16
2.17
LCD/LVDS interface Connections ................................. 17
2.17.1 LVDS Connector (CN16) ............................................. 17
2.17.2 LCD Backlight Connector (CN22) ............................... 17
2.18
2.19
USB Connectors (CN7, CN8) ......................................... 17
Ethernet configuration..................................................... 17
2.19.1 LAN Connector (CN12) ............................................... 18
2.19.2 Network boot ................................................................ 18
2.20
Front Panel Connector (CN1) ......................................... 18
2.20.1
2.20.2
2.20.3
2.20.4
2.20.5
2.21
2.22
2.23
2.24
2.25
Chapter
Reset (Pin7&Pin8) ........................................................ 18
HDD LED (Pin1&Pin2)................................................ 18
Power LED (Pin 3 & Pin 4) .......................................... 18
Suspend LED (Pin 5 & Pin 6)....................................... 18
Power Button (Pin 9 & Pin10)...................................... 18
COM port Connector (CN13,CN14,CN15) .................... 19
PS/2, KB/Mouse Connector (CN20)............................... 19
AC'97 interface Connector (CN11)................................. 19
DI/O Connector (CN9).................................................... 19
SATA Connector (SA1, SA2)......................................... 20
3 Software Configuration .................................22
3.1
3.2
Introduction ..................................................................... 22
VGA display firmware configuration ............................. 22
3.3
Connectors to Standard LCDs......................................... 24
Figure 3.1:VGA setup screen........................................ 23
3.3.1
Chapter
AU M170EG01 (1280 x1024 LVDS LCD).................. 24
Table 3.1:Connections to LCD/Flat Panel (CN15)....... 24
4 Award BIOS Setup.........................................26
4.1
System test and initialization........................................... 26
4.1.1
4.2
System configuration verification................................. 26
Award BIOS setup .......................................................... 27
4.2.1
4.2.2
4.2.3
4.2.4
4.2.5
PCI-6882 User Manual
Entering setup ............................................................... 27
Figure 4.1:BIOS setup program initial screen .............. 27
Standard CMOS Features setup.................................... 28
Figure 4.2:Standard CMOS Features setup .................. 28
Advanced BIOS Features setup .................................... 29
Figure 4.3:Advanced BIOS Features setup................... 29
Advanced Chipset Features setup ................................. 30
Figure 4.4:Advanced Chipset Features setup ............... 30
Integrated Peripherals ................................................... 31
Figure 4.5:Integrated Peripherals.................................. 31
viii
4.2.6
4.2.7
4.2.8
4.2.9
4.2.10
4.2.11
4.2.12
4.2.13
Chapter
5 PCI SVGA Setup ............................................42
5.1
Introduction ..................................................................... 42
5.1.1
5.1.2
5.1.3
5.2
Installation for Windows 2000/XP ............................... 43
Further Information ......................................................... 46
6 PCI Bus Ethernet Interface...........................48
6.1
6.2
Introduction ..................................................................... 48
Installation of Ethernet driver ......................................... 48
6.2.1
Chapter
Chipset .......................................................................... 42
Display memory............................................................ 42
Display types................................................................. 42
Installation of the SVGA Driver ..................................... 43
5.2.1
5.3
Chapter
Power Management Setup ............................................ 32
Figure 4.6:Power Management Setup........................... 32
PnP/PCI Configurations................................................ 33
Figure 4.7:PnP/PCI Configurations .............................. 33
PC Health Status ........................................................... 34
Figure 4.8:PC Health Status.......................................... 34
Frequency/Voltage Control........................................... 35
Figure 4.9:Frequency/Voltage Control ......................... 35
Load Optimized Defaults.............................................. 36
Figure 4.10:Load BIOS defaults screen........................ 36
Set Password ................................................................. 36
Figure 4.11:Set password.............................................. 37
Save & Exit Setup......................................................... 38
Figure 4.12:Save to CMOS and EXIT.......................... 38
Exit Without Saving ............................................... 39
Figure 4.13:Quit without saving ................................... 39
Installation for Windows XP ........................................ 49
7 Audio Setup.....................................................54
7.1
7.2
Introduction ..................................................................... 54
Driver installation............................................................ 54
7.2.1
7.2.2
Before you begin.......................................................... 54
Windows XP driver ..................................................... 54
Appendix A Programming DI/O & Watchdog Timer......58
A.1
Supported DI/O Register................................................. 58
A.1.1
A.1.2
A.2
DI/O Registers .............................................................. 58
DI/O Example program-1 ............................................. 59
Watchdog programming................................................. 59
Appendix B
Pin Assignments ............................................62
B.1
Front Panel Connector (CN1) ......................................... 62
B.2
Floppy ................................................. Connector (CN2)63
Table B.1:Front Panel Connector (CN1) ...................... 62
ix
Table B.2:Floppy Connector (CN2) ............................. 63
B.3
Secondary IDE Connector (CN3) ................................... 64
B.4
Primary IDE Connector (CN4) ................................... 65
B.5
Printer Connector (CN5) ................................................. 66
B.6
+12V Connector (CN6) ............................................. 67
B.7
USB port 0, 1(CN7) ........................................................ 67
B.8
USB port 2, 3 (CN8) ....................................................... 67
B.9
DI/O Connector (CN9).................................................... 68
B.10
VGA D-SUB Connector (CN10) .................................... 69
B.11
AC’97 Interface Connector (CN11) ............................ 69
B.12
LAN Connector (CN12).................................................. 70
B.13
COM2 (RS-232/422/485) (CN13) .................................. 70
B.14
COM 3, 4 Connector (CN14) ..................................... 71
B.15
COM1 Connector (CN15)............................................... 71
B.16
LVDS Connector (CN16)................................................ 72
B.17
IrDA Connector (CN17) ............................................ 72
B.18
TV-out Connector (CN18) ......................................... 73
B.19
AT Keyboard Connector (CN19) ................................ 73
B.20
ATX power Connector (CN21)....................................... 74
B.21
LCD backlight Connector (CN22) .................................. 74
B.22
CompactFlash Connector (CN23)................................... 75
B.23
FAN Connector (FAN1) ............................................ 76
B.24
Serial ATA (SA1,SA2) ................................................... 76
Table B.3:Secondary IDE Connector (CN3) ................ 64
Table B.4:Primary IDE Connector (CN4) .................... 65
Table B.5:Printer Connector (CN5).............................. 66
Table B.6:+12V Connector (CN6) ............................... 67
Table B.7:USB port 0, 1 (CN7) .................................... 67
Table B.8:USB port 2, 3 (CN8) .................................... 67
Table B.9:DI/O Connector (CN9) ................................ 68
Table B.10:VGA D-SUB Connector (CN10) ............... 69
Table B.11: AC’97 Interface Connector (CN11).......... 69
Table B.12: LAN Connector (CN12) ........................... 70
Table B.13:COM2 connector (CN13) .......................... 70
Table B.14:COM 3, 4 Connector (CN14)..................... 71
Table B.15:COM1 Connector (CN15).......................... 71
Table B.16:LVDS Connector (CN16) .......................... 72
Table B.17:IrDA Connector (CN17) ............................ 72
Table B.18:TV-out Connector (CN18)......................... 73
Table B.19:AT Keyboard Connector (CN19)............... 73
Table B.20:ATX power Connector (CN21) ................. 74
Table B.21:LCD backlight Connector (CN22)............. 74
Table B.22:CompactFlash Connector (CN23).............. 75
Table B.23:FAN Connector (FAN1) ............................ 76
PCI-6882 User Manual
x
Table B.24:Serial ATA (SA1, SA2) ............................. 76
Appendix C
System Assignments ......................................80
C.1
System I/O Ports.............................................................. 80
C.2
1st MB memory map....................................................... 81
C.3
DMA channel assignments.............................................. 81
C.4
Interrupt assignments ...................................................... 82
Table C.1:System I/O ports .......................................... 80
Table C.2:1st MB memory map ................................... 81
Table C.3:DMA channel assignments .......................... 81
Table C.4:Interrupt assignments ................................... 82
xi
PCI-6882 User Manual
xii
CHAPTER
1
General Information
This chapter gives background
information on the PCI-6882.
Sections include:
•
•
•
•
Introduction
Features
Specifications
Board layout and dimensions
1
Chapter 1 General Information
Chapter 1 General Information
1.1 Introduction
The PCI-6882 series is a half-sized PCI bus CPU card designed with
powerful Intel® Pentium® 4, Celeron® D or Celeron processor, with
Intel 852GME and ICH4 chipset, which supports Dynamic Video Memory Technology. For maximum performance, PCI-6882 also supports two
200 PIN DDR SODIMM sockets for non-ECC DDR memory up to 2 GB.
These chipsets are specifically for embedded computing and provide an
optimized onboard integrated graphics solution. Hyper-Threading technology intelligently focuses system power where the CPU needs it and
automatically regulates power usage to preserve battery life.
Other onboard features include 2 EIDE, 2 SATA, 1 FDD, 4 USB 2.0, 4
COM ports (3 x RS-232 and 1 x RS-232/422/485), PS/2 Keyboard/
mouse, watchdog, and a DI/O interface. The SSD solution supports Type
I/II CompactFlash cards.
PCI-6882 uses the Intel 852GME chipset which supports CRT/LVDS
interface and a 2 channel (36-bit) LVDS LCD panel. PCI-6882 supports
AC’97 audio with the addition of the optional PCM-231A-00A1 audio
module.
The Ethernet interface supports IEEE 802.3u (100Base-T) by Intel
82551ER (82551QM optional), and 1000Base-T by Intel 82541PI (PCI6882FG-00A1). PCI-6882 follows standard PCI slot dimensions, this
means it can match with all half-sized chassis and can operate in high
vibration environments.
1.2 Features
• Intel new generation Intel Pentium 4/Celeron D/Celeron Processor
Embedded
• Operation at 0~60° C
• Onboard PCI CRT/LVDS/TV-out display
• Supports 1000Base-T Ethernet on board (PCI-6882FG-00A1)
• Supports 2 SATA
• Supports 4 x USB 2.0 ports
PCI-6882 User Manual
2
• Supports 2 Channel 18 bits LVDS for LCD
• Supports 400/533 MHz Front Side Bus
• Supports 200 MHz, 266 MHz and 333 MHz DDR SDRAM
1.3 Specifications
1.3.1 Standard SBC Functions
• CPU: Intel Pentium 4 processor, up to 3.06 GHz; Celeron D and Celeron processor, up to 2.8 GHz; Supports 400 MHz FSB processors.
• System Chipset: Intel 852GME + ICH4
• BIOS: Award 4 Mbit Flash memory
• System memory: 200 pin DDR SODIMM x 2, supports non-ECC DDR
up to 2 GB
• 2nd cache memory: 512 KB on Pentium® 4 processor, 256 KB on Celeron® D processor, 128 KB on Celeron® processor
• Enhanced IDE Interface: Supports two enhanced IDE channels. Primary channel supports up to ATA-100 mode; Secondary channel
only supports up to ATA-33. The CFC card occupies the secondary
master channel
• COM Ports: Four COM ports, COM1, COM3, COM4: RS-232,
COM2: RS-232/422/485
• Printer Port: One printer port, supports SPP/EPP/ECP
• Keyboard/Mouse Connector: One 6-pin socket on bracket for standard PS/2 Mouse and Keyboard, one 5-pin wafer box connector for
external Keyboard only.
• Power Management: Supports Power Saving Mode including Normal/
Standard/Suspend modes. APM 1.2 compliant. ACPI 1.0b, ACPI
2.0 supported
• FDD interface: Supports up to two FDD devices
• Watchdog Timer: 0~255 Sec., System reset
• Expansion Interface: PCI interface, compatible with PCI Rev 2.2
• USB: 4 USB ports, USB 2.0 compliant
• SATA Connector: Two COMAX C504C connectors, supports data
transfer rate up to 150 MB/s, Software RAID 0, 1 supported
(Depend on Adapter)
• DI/O Interface: 8-bit general purpose input/output (optional)
• SSD: Supports CompactFlash Card Type I/II
• IrDA: 115 kbps, IrDA1.1 compliant
• Audio: Supports AC’97 Audio with optional PCM-231A-00A1
3
Chapter 1 General Information
1.3.2 Display Interface
• Chipset: Intel 852GME chip integrated
• Memory size: Optimized Shared Memory Architecture, supports up to
64 MB frame buffer using system memory
• Display modes:
CRT Modes: 1920 x 1440 @ 60 Hz; 1600 x 1200 @ 85 Hz
LCD Modes: up to 1280 x 1024 @ 36bpp
• LCD Interface: 2 Channel LVDS (2 x 18-bit)
• LVDS Interface: Hirose connector supports dual channel LVDS panel,
up to UXGA panel resolution with frequency range from 25 MHz to
112 MHz
• Dual Display: CRT + LVDS, LVDS + TV-out, CRT + TV-out, LVDS
+ LVDS (under Windows, Linux)
1.3.3 TV-out (optional)
• Chipset: Chrontel CH7009
• Supports NTSC and PAL video standards
• Supports composite, s-video or AV output
• Supports graphic resolutions up to 1024 x 768 pixels
1.3.4 Solid State Disk
• Supports CompactFlash Card I/II
1.3.5 Ethernet Interface
• Chipset: Intel 82541PI (Gigabit), Intel 82551ER/82551QM (optional)
• Connection: Onboard RJ-45 connector
• Interface: IEEE 802.3 z/ab (1000Base-T) or IEEE 802.3u (100Base-T)
protocol compatible
1.3.6 Mechanical and Environmental
• Dimensions (L x W): 185 x 122 mm (7.3” x 4.8”)
• Power supply voltage: +5 V, +5 V STB, +12 V
• Power requirements:
Max:
7.8 A @+12 V, 2.4 [email protected]+5 V (with Pentium4 3.06 GHz + 1 GB);
Typical:
2.3 A @+12 V, 2.3 A @+5 V (with Pentium4 3.06 GHz + 1 GB);
• Operating temperature: 0 ~ 60° C (32 ~ 140° F) operation
• Operating humidity: 0 ~ 90% Relative Humidity, Non condensing
PCI-6882 User Manual
4
1.4 Board layout: dimensions
3.00
185.00
154.33
129.06
4.00
2.80
70.76
6.41
22.50
6.48
36.13
4.19
4.01
4.01
14.29
4.13
24.38
6.41
59.44
4.91
56.26
62.48
24.93
6.08
76.20
65.75
25.35
121.92
58.80
16.19
13.06
7.07
65.66
2.68
30.56
9.91
27.43
20.14
2.89
5.72
7.60
36.08
11.43
65.75
5.08
104.47
Figure 1.1: Board layout: dimensions (component side)
46.35
5.40
20.86
75.72
Figure 1.2: Board layout: dimensions (solder side)
5
Chapter 1 General Information
PCI-6882 User Manual
6
CHAPTER
2
Installation
This chapter explains the setup procedures
of PCI-6882 hardware, including instructions on setting jumpers and connecting
peripherals, switches and indicators. Be
sure to read all safety precautions before
you begin the installation procedure.
7
Chapter 2 Installation
Chapter 2 Installation
2.1 Jumpers
The PCI-6882 has a number of jumpers that allow you to configure your
system to suit your application. The table below lists the functions of the
various jumpers.
Table 2.1: Jumpers
Label
Function
J1
CMOS setting
J2
COM2 RS-232/422/485 setting Connector
J3
LCD voltage setting
J4
SMBus Connector
JP1
CPU FSB setting Connector
JP2
PCI VIO setting Connector
BT1
Battery socket
PCI-6882 User Manual
8
2.2 Connectors
Onboard connectors link the PCI-6882 to external devices such as hard
disk drives, a keyboard, or floppy drives. The table below lists the function of each of the board’s connectors.
Table 2.2: Connectors
Label
Function
CN1
Front Panel Connector
CN2
Floppy Connector
CN3
Secondary IDE Connector
CN4
Primary IDE Connector
CN5
Printer Connector
CN6
+12V Connector
CN7
USB port 0, 1
CN8
USB port 2, 3
CN9
DI/O Connector
CN10
D-SUB VGA Connector
CN11
AC’97 interface Connector
CN12
LAN Connector
CN13
COM2 (RS-232/422/485)
CN14
COM3, COM4 (RS-232)
CN15
COM1 Connector
CN16
LVDS Connector
CN17
IrDA Connector
CN18
TV-out Connector
CN19
AT keyboard Connector
CN20
PS/2 Mouse/Keyboard Connector
CN21
ATX Connector
CN22
LCD Backlight Connector
CN23
CompactFlash Socket
SA1
SATA Connector
SA2
SATA Connector
FAN1
FAN Connector
9
Chapter 2 Installation
2.3 Locating Connectors
CN1 CN2
CN5
CN3
CN4
SA1
SA2
CN6
FAN1
CN7
CN8
CN9
CPU1
CN10
CN11
CN12
J1
CN13
CN15
CN14
J2
CN21
CN20
J4
CN19 CN22 CN18 CN17 JP1
J3 JP2
CN16
Figure 2.1: Jumper & Connector Locations (component side)
CN3
CN23
CN21
Figure 2.2: Connectors (solder side)
PCI-6882 User Manual
10
2.4 Setting Jumpers
You may configure your card to match the needs of your application by
setting jumpers. A jumper is a metal bridge used to close an electric circuit. It consists of two metal pins and a small metal clip (often protected
by a plastic cover) that slides over the pins to connect them. To close a
jumper, you connect the pins with the clip. To open a jumper, you remove
the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3. In
this case you would connect either pins 1 and 2, or 2 and 3.
open
closed
closed 2-3
The jumper settings are schematically depicted in this manual as follows:.
open
closed
closed 2-3
A pair of needle-nose pliers may be helpful when working with jumpers.
If you have any doubts about the best hardware configuration for your
application, contact your local distributor or sales representative before
you make any changes. Generally, you simply need a standard cable to
make most connections.
11
Chapter 2 Installation
2.5 COM2 RS-232/422/485 Select (J2)
1
2
3
4
5
6
Table 2.3: COM2 RS-232/422/485 Select
1-2 (default)
RS-232
3-4
RS-422
5-6
RS-485
Empty
The IR function is available
2.6 Clear CMOS (J1)
Warning!
To avoid damaging the computer, always turn
off the power supply before setting “Clear
CMOS.” Before turning on the power supply,
set the jumper back to “3.0 V Battery On.”
This jumper is used to erase CMOS data (including the setting of date,
time and password) and reset system BIOS information.
The procedure for clearing CMOS is:
1.
Turn off the system.
2.
Short pin 1 and pin 2.
3.
Turn on the system. The BIOS is now reset to its default setting
Table 2.4:
Clear CMOS (J1)
Clear CMOS
PCI-6882 User Manual
12
2.7 LCD voltage setting (J3)
1
2
3
1
2
3
Table 2.5: LCD voltage setting (J3)
Pin
Function
1-2(default)
+5 V
2-3
+3.3 V
2.8 SMBus Connector (J4)
Table 2.6: SMBus Connector (J4)
Pin
Function
1
+5 V
2
SM_CLOCK
3
SM_DATA
4
GND
2.9 CPU FSB select Connector (JP1)
Table 2.7: CPU FSB select Connector (JP1)
Pin
Function
1~2 (default)
Auto detect
2~3
100 MHz
Empty
133 MHz
2.10 PCI VIO setting Connector (JP2)
Table 2.8: PCI VIO setting Connector (JP2)
Pin
Function
1~2 (default)
+5 V
2~3
+3.3 V
13
Chapter 2 Installation
2.11 Installing SODIMMs
Notes
The modules can only fit into a socket one way.
The gold pins must point down into the
SODIMM socket.
Follow the below procedure for installing SODIMMs. Please follow these
steps carefully.
1. Make sure that all power supplies to the system are switched off
2. Install the SODIMM card. Install the SODIMM so that its gold pins
point down into the SODIMM socket.
3. Slip the SODIMM into the socket at a 45 degree angle and carefully fit the bottom of the card against the connectors.
4. Gently push the SODIMM into a perpendicular position until the
clips on the ends of the SODIMM sockets snap into place.
5. Check to ensure that the SODIMM is correctly seated and all connector contacts touch. The SODIMM should not move around in its
socket.
2.12 ATX power control Connector (CN21)
The PCI-6882 supports ATX power. CN21 supplies main power (PS-ON,
5 VSB), and is a 3 pins power connector, w/Fixed Lock, type: 4200-WSA1.
Important
Make sure that the ATX power supply can take
at least a 10 mA load on the 5 V standby lead
(5VSB). If not, you may have difficulty powering on your system.
2.13 Printer port Connector (CN5)
Normally, the printer port is used to connect the card to a printer. The
PCI-6882 includes a multi-mode (ECP/EPP/SPP) printer port accessed
via CN5 and a 26-pin flat-cable connector. You will need an adapter
PCI-6882 User Manual
14
cable if you use a traditional DB-25 connector. The adapter cable has a
26-pin connector on one end, and a DB-25 connector on the other.
The printer port is designated as LPT1, and can be disabled or changed to
LPT2 or LPT3 in the system BIOS setup.
The printer port interrupt channel is designated to be IRQ7.
You can select ECP/EPP DMA channel via BIOS setup.
2.14 CompactFlash Card Socket
The PCI-6882 provides a 50-pin socket for CompactFlash card type I/II.
2.14.1 CompactFlash (CN23)
The CompactFlash card occupies a secondary IDE channel which can be
enabled/disabled via the BIOS settings.
2.15 Floppy drive Connector (CN2)
You can attach up to two floppy drives to the PCI-6882’s onboard controller. You can use any combination of 5.25” (360 KB and 1.2 MB) and/
or 3.5” (720 KB, 1.44 MB, and 2.88 MB) drives.
A 34-pin daisy-chain drive connector cable is required for a dual-drive
system. On one end of the cable is a 34-pin flat-cable connector. On the
other end are two sets of floppy disk drive connectors. Each set consists
of a 34-pin flat-cable connector (usually used for 3.5” drives) and a
printed-circuit board connector (usually used for 5.25” drives).
2.15.1 Connecting the floppy drive
1.
Plug the 34-pin flat-cable connector into CN2. Make sure that the
red wire corresponds to pin one on the connector.
2.
Attach the appropriate connector on the other end of the cable to
the floppy drive(s). You can use only one connector in the set. The
set on the end (after the twist in the cable) connects to the A: drive.
The set in the middle connects to the B: drive.
3.
If you are connecting a 5.25” floppy drive, line up the slot in the
printed circuit board with the blocked-off part of the cable connector.
If you are connecting a 3.5” floppy drive, you may have trouble determining which pin is number one. Look for a number printed on the circuit
board indicating pin number one. In addition, the connector on the floppy
drive may have a slot. When the slot is up, pin number one should be on
15
Chapter 2 Installation
the right. Check the documentation that came with the drive for more
information.
If you desire, connect the B: drive to the connectors in the middle of the
cable as described above.
In case you need to make your own cable, you can find the pin assignments for the board’s connector in Appendix B.
2.16 IDE Connector (CN3,CN4)
The PCI-6882 provides two IDE channels to which you can attach up to
four Enhanced Integrated Device Electronics hard disk drives or CDROM to the PCI-6882’s internal controller. The PCI-6882's IDE controller uses a PCI interface. This advanced IDE controller supports faster data
transfer. Primary channel (CN4) supports ATA-100 mode; Secondary
channel (CN3) only supports ATA-33 and PIO mode. The CFC card
occupies the secondary master channel.
2.16.1 Connecting the hard drive
Connecting drives is done in a daisy-chain fashion. It requires one of two
cables (not included in this package), depending on the drive size. 1.8"
and 2.5" drives need a 1 x 44-pin to 2 x 44-pin flat-cable connector. 3.5"
drives use a 1 x 44-pin to 2 x 40-pin connector.
Wire number 1 on the cable is red or blue, and the other wires are gray.
1.
Connect one end of the cable to CN3, CN4. Make sure that the red
(or blue) wire corresponds to pin 1 on the connector, which is
labelled on the board (on the right side).
2.
Plug the other end of the cable into the Enhanced IDE hard drive,
with pin 1 on the cable corresponding to pin 1 on the hard drive.
(See your hard drive’s documentation for the location of the connector.)
If desired, connect a second drive as described above.
Unlike floppy drives, IDE hard drives can connect to either end of the
cable. If you install two drives, you will need to set one as the master and
one as the slave by using jumpers on the drives. If you install only one
drive, set it as the master.
PCI-6882 User Manual
16
2.17 LCD/LVDS interface Connections
The PCI-6882’s display interface can drive conventional CRT displays
and is capable of driving a wide range of LVDS flat panel displays as
well. The board has two display connectors: one for standard CRT VGA
monitors, and one for LVDS flat panel displays.
2.17.1 LVDS Connector (CN16)
PCI-6882 uses the Intel 852GME to support single or dual-channel
LVDS panels up to UXGA panel resolution with frequency range from
25 MHz to 112 MHz.
The display mode can be 2 channels (2 x 18bit) LVDS LCD panel displays Users can connect to either an 18, 24, or 36bit LVDS LCD with
CN16.
2.17.2 LCD Backlight Connector (CN22)
The LCD inverter is connected to CN22 via a 5-pin connector to provide
+5 V / +12 V power.
2.18 USB Connectors (CN7, CN8)
The PCI-6882 board provides up to four USB (Universal Serial Bus)
ports. This gives complete Plug and Play, and hot attach/detach for up to
127 external devices. The USB interfaces complies with USB specification Rev. 2.0, and are fuse protected.
The USB interface is accessed through the 5 x 2-pin flat-cable connector,
CN7 (USB0, 1), and CN8 (USB2, 3). You will need an adapter cable if
you use a standard USB connector. The adapter cable has a 5 x 2-pin connector on one end and a USB connector on the other.
The USB interfaces can be disabled in the system BIOS setup.
2.19 Ethernet configuration
The PCI-6882 is equipped with a high performance 32-bit PCI-bus Ethernet interface which is fully compliant with IEEE 802.3u 10/100 Mbps
CSMA/CD standards. It is supported by all major network operating systems.
The PCI-6882 supports 10/100Base-T or 1000Base-T Ethernet connections with onboard RJ-45 connectors (CN12). PCI-6882F series supports
10/100Base-T LAN, PCI-6882FG series supports 1000Base-T LAN.
17
Chapter 2 Installation
2.19.1 LAN Connector (CN12)
10/100 or 1000 Base-T connects to the PCI-6882 via a cable to a standard
RJ-45 connector.
2.19.2 Network boot
The Network Boot feature can be utilized by incorporating the Boot
ROM image files for the appropriate network operating system. The Boot
ROM BIOS files are included in the system BIOS, which is on the utility
CD disc. Boot ROM function supported by 82541PI and 82551QM
(optional), 82551ER can not support this function.
2.20 Front Panel Connector (CN1)
Next is to install external switches to monitor and control PCI-6882.
These features are optional: install them only if necessary. CN1 is an 2 x
5 pin header, 180 degree, male.It provides connections for reset and
power & hard disk indicator.
2.20.1 Reset (Pin7&Pin8)
If a reset switch is installed, it should be an open single pole switch.
Momentarily pressing the switch will activate a reset. The switch should
be rated for 10 mA, 5 V.
2.20.2 HDD LED (Pin1&Pin2)
The HDD LED indicator for hard disk access is an active low signal (24
mA sink rate).
Pin 1 & Pin 2
The HDD LED indicator lights up when the HDD is operating.
2.20.3 Power LED (Pin 3 & Pin 4)
Pin 3 & Pin 4
The Power LED indicator lights up when the power is on.
2.20.4 Suspend LED (Pin 5 & Pin 6)
Pin 5 & Pin 6
The Suspend LED indicator lights up when the computer is in suspend
mode.
2.20.5 Power Button (Pin 9 & Pin10)
The PCI-6882 provides an ATX power input connector. When connected
with Pin 9 & Pin 10, it enables power On/Off from the chassis.
PCI-6882 User Manual
18
2.21 COM port Connector (CN13,CN14,CN15)
The PCI-6882 provides four COM ports (COM1, COM3, COM4: RS-232
and COM2: RS-232/422/485). CN15 supports COM1, CN13 supports
COM2, CN14 supports COM3, COM4. and J2 is for COM2 RS-232/422/
485 selection. It provides connections for serial devices (a mouse, etc.) or
a communication network. You can find the pin assignments for the
COM port connector in Appendix B.
2.22 PS/2, KB/Mouse Connector (CN20)
The PCI-6882 board provides a keyboard connector that supports both a
keyboard and a PS/2 style mouse. In most cases, especially in embedded
applications, a keyboard is not used. If the keyboard is not present, the
standard PC/AT BIOS will report an error or fail during power-on selftest (POST) after a reset. The PCI-6882’s BIOS standard setup menu
allows you to select "All, But Keyboard" under the "Halt On" selection.
This allows no-keyboard operation in embedded system applications,
without the system halting under POST.
2.23 AC'97 interface Connector (CN11)
PCI-6882 can support separate independent PCI functions for Audio and
Modem, which is compliant to AC'97 2.2 standard.
The AC'97 interface is a 5 x 2 pin box header. PCI-6882 can support
Audio with the addition of optional PCM-231A-00A1. Detailed pin
assignment refer to Appendix B.
2.24 DI/O Connector (CN9)
The PCI-6882 supports DI/O interface by CN9, which is a 5 x 2 dual line
pin header, supplying 8-bit general purpose input or output ports.
Generally, Digital Input and Output are signals to control external devices
that need an On/Off circuit or TTL devices. For detailed signal assignment refer to Appendix A.
19
Chapter 2 Installation
2.25 SATA Connector (SA1, SA2)
PCI-6882 can support Serial ATA by two COMAX C504C connectors
(SA1, SA2), with data transfer rates up to 150 Mb/s, enabling very fast
data and file transfer, and independent DMA operation on two ports. It
also supports alternate Device ID and RAID Class Code option for support of Soft RAID.
PCI-6882 User Manual
20
CHAPTER
3
Software Configuration
This chapter details the software configuration information. It shows you
how to configure the card to match
your application requirements. Award
System BIOS will be covered in
Chapter 4.
Sections include:
• Introduction
• VGA display software configuration
• Connectors to Standard LCDs
Chapter 3 Software Configuration
3.1 Introduction
The system BIOS and custom drivers are located in a 512 KB, 32-pin
(JEDEC spec.) Flash ROM device, designated U10. A single Flash chip
holds the system BIOS, VGA BIOS, and network Boot ROM image. The
display can be configured via software. This method minimizes the number of chips and eases configuration. You can change the display BIOS
simply by reprogramming the Flash chip.
NOTE:
Due to Intel not supporting Win98 and Windows
ME, it is not recommended to install Win98,
Windows ME drivers on PCI-6882.
3.2 VGA display firmware configuration
The onboard VGA interface supports a wide range of popular LCD, flat
panel displays and traditional analog CRT monitors. The 852GME chip
with optimized Shared Memory Architecture, supports up to 64 MB
frame buffer using system memory to provide LVDS mode up to 1280 x
1024 @ 36bpp, the interface can drive CRT displays with resolutions up
to 1920 x 1440 @ 60 Hz and 1600 x 1200 @ 85 Hz.
The VGA interface is configured completely via the software utility, so
you do not have to set any jumpers. Configure the VGA display as follows:
1.
Apply power to the board with a color TFT display attached. This
is the default setting for this board. Ensure that the AWDFLASH.EXE and *.BIN files are located in the working drive.
NOTE:
Ensure that you do not run AWDFLASH.EXE
while your system is operating in EMM386
mode.
PCI-6882 User Manual
22
2.
At the prompt, type AWDFLASH.EXE and press <Enter>. The
VGA configuration program will then display the following:
Figure 3.1: VGA setup screen
3.
At the prompt, enter the new BIN file which supports your display.
When you are sure that you have entered the file name correctly
press <Enter>.
4.
The screen will ask “Do you want to save BIOS?”. If you change
your mind or made a mistake, press N to abort and end the setup
procedure. Press Y if you wish to save the existing configuration
before changing it. Then type the name under which you want to
save the current configuration.
5.
The prompt will then ask “Are you sure to program?”. Press Y if
you want the new file to be written into the BIOS. Press N to exit
the program.
The new VGA configuration will then write to the ROM BIOS chip. This
configuration will remain the same until you run the AWDFLASH.EXE
program and change the settings.
23
Chapter 3
3.3 Connectors to Standard LCDs
The following table illustrates typical LCD connection pinouts for the
PCI-6882.
3.3.1 AU M170EG01 (1280 x1024 LVDS LCD)
Table 3.1: Connections to LCD/Flat Panel (CN15)
LCD Connector
JAE FI-X30C2L
Flat Panel Connector
DF13-40P
Pin
Signal
Pin
Signal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
RxOIN0RxOIN0+
RxOIN1RxOIN1+
RxOIN2RxOIN2+
VSS
RxOCLKINRxOCLKIN+
RxOIN3RxOIN3+
RxEIN0RxEIN0+
VSS
RxEIN1RxEIN1+
VSS
RxEIN2RxEIN2+
RxECLKINRxECLKIN+
RxEIN3RxEIN3+
VSS
VSS
NC
VSS
VCC
VCC
7
9
13
15
19
21
23
25
27
35
37
8
10
4
14
16
12
20
22
26
28
36
38
34
30
X
34
1
2
OD0OD0+
OD1OD1+
OD2OD2+
GND
OCKOCK+
OD3OD3+
ED0ED0+
WP#
ED1ED1+
GND
ED2ED2+
ECKECK+
ED3ED3+
GND
GND
PCI-6882 User Manual
24
GND
VDDSAFE
VDDSAFE
CHAPTER
4
Chapter 4 Ducks that Need Love!
Award BIOS Setup
This chapter describes how to set BIOS
configuration data.
25
Chapter 4 Award BIOS Setup
4.1 System test and initialization
These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see
an error message on the screen. There are two kinds of errors: fatal and
non-fatal. The system can usually continue the boot up sequence with
non-fatal errors. Non-fatal error messages usually appear on the screen
along with the following instructions:
press <F1> to CONTINUE
Write down the message and press the F1 key to continue the bootup
sequence.
4.1.1 System configuration verification
These routines check the current system configuration against the values
stored in the board’s CMOS memory. If they do not match, the program
outputs an error message. You will then need to run the BIOS setup program to set the configuration information in memory.
There are three situations in which you will need to change the CMOS
settings:
1.
You are starting your system for the first time
2.
You have changed the hardware attached to your system
3.
The CMOS memory has lost power and the configuration information has been erased.
The PCI-6882 Series' CMOS memory has an integral lithium battery
backup. The battery backup should last at least three years in normal service, but when it finally runs down, you will need to replace the complete
unit.
PCI-6882 User Manual
26
4.2 Award BIOS setup
Award’s BIOS ROM has a built-in Setup program that allows users to
modify the basic system configuration. This type of information is stored
in battery-backed CMOS RAM so that it retains the Setup information
when the power is turned off.
4.2.1 Entering setup
Power on the computer and press <Del> immediately. This will allow you
to enter Setup.
Figure 4.1: BIOS setup program initial screen
27
4.2.2 Standard CMOS Features setup
When you choose the Standard CMOS Features option from the Initial
Setup Screen menu, the screen shown below is displayed. This standard
Setup Menu allows users to configure system components such as date,
time, hard disk drive, floppy drive and display. Once a field is highlighted, on-line help information is displayed in the right top of the Menu
screen.
Figure 4.2: Standard CMOS Features setup
PCI-6882 User Manual
28
4.2.3 Advanced BIOS Features setup
By choosing the Advanced BIOS Features Setup option from the Initial
Setup Screen menu, the screen below is displayed. This sample screen
contains the manufacturer’s default values for the PCI-6882 Series.
Figure 4.3: Advanced BIOS Features setup
29
4.2.4 Advanced Chipset Features setup
By choosing the Advanced Chipset Features option from the Initial Setup
Screen menu, the screen below is displayed. This sample screen contains
the manufacturer’s default values for the PCI-6882 Series.
Figure 4.4: Advanced Chipset Features setup
PCI-6882 User Manual
30
4.2.5 Integrated Peripherals
Choosing the Integrated Peripherals option from the Initial Setup Screen
menu should produce the screen below. Here we see the manufacturer’s
default values for the PCI-6882 Series.
Figure 4.5: Integrated Peripherals
31
4.2.6 Power Management Setup
By choosing the Power Management Setup option from the Initial Setup
Screen menu, the screen below is displayed. This sample screen contains
the manufacturer’s default values for the PCI-6882 Series.
Figure 4.6: Power Management Setup
PCI-6882 User Manual
32
4.2.7 PnP/PCI Configurations
By choosing the PnP/PCI Configurations option from the Initial Setup
Screen menu, the screen below is displayed. This sample screen contains
the manufacturer’s default values for the PCI-6882 Series.
Figure 4.7: PnP/PCI Configurations
33
4.2.8 PC Health Status
The PC Health Status option displays information such as CPU and motherboard temperatures, fan speeds, and core voltage.
Figure 4.8: PC Health Status
PCI-6882 User Manual
34
4.2.9 Frequency/Voltage Control
By choosing the Frequency/Voltage Control option from the Initial Setup
Screen menu, the screen below is displayed. This sample screen contains
the manufacturer’s default values for the PCI-6882
Figure 4.9: Frequency/Voltage Control
Caution
Incorrect settings in Frequency/Voltage Control
may damage the system CPU, video adapter,
or other hardware.
35
4.2.10 Load Optimized Defaults
Load Optimized Defaults loads the default system values directly from
ROM. If the stored record created by the Setup program should ever
become corrupted (and therefore unusable), these defaults will load automatically when you turn the PCI-6882 Series system on.
Figure 4.10: Load BIOS defaults screen
4.2.11 Set Password
Note
To enable this feature, you should first go to the
Advanced BIOS Features menu, choose the
Security Option, and select either Setup or
System, depending on which aspect you want
password protected. Setup requires a password only to enter Setup. System requires the
password either to enter Setup or to boot the
system.
A password may be at most 8 characters long.
PCI-6882 User Manual
36
To Establish Password
1.
Choose the Set Password option from the CMOS Setup Utility
main menu and press <Enter>.
2.
When you see “Enter Password,” enter the desired password and
press <Enter>.
3.
At the “Confirm Password” prompt, retype the desired password,
then press <Enter>.
4.
Select Save to CMOS and EXIT, type <Y>, then <Enter>.
Figure 4.11: Set password
To Change Password
1.
Choose the Set Password option from the CMOS Setup Utility
main menu and press <Enter>.
2.
When you see “Enter Password,” enter the existing password and
press <Enter>.
3.
You will see “Confirm Password.” Type it again, and press
<Enter>.
4.
Select Set Password again, and at the “Enter Password” prompt,
enter the new password and press <Enter>.
37
5.
At the “Confirm Password” prompt, retype the new password, and
press <Enter>.
6.
Select Save to CMOS and EXIT, type <Y>, then <Enter>.
To Disable Password
1.
Choose the Set Password option from the CMOS Setup Utility
main menu and press <Enter>.
2.
When you see “Enter Password,” enter the existing password and
press <Enter>.
3.
You will see “Confirm Password.” Type it again, and press
<Enter>.
4.
Select Set Password again, and at the “Enter Password” prompt,
don’t enter anything; just press <Enter>.
5.
At the “Confirm Password” prompt, again don’t type in anything;
just press <Enter>.
6.
Select Save to CMOS and EXIT, type <Y>, then <Enter>.
4.2.12 Save & Exit Setup
Figure 4.12: Save to CMOS and EXIT
PCI-6882 User Manual
38
If you select this option and press <Y> then <Enter>, the values entered
in the setup utilities will be recorded in the chipset’s CMOS memory. The
microprocessor will check this every time you turn your system on and
use the settings to configure the system. This record is required for the
system to operate.
4.2.13 Exit Without Saving
Figure 4.13: Quit without saving
Selecting this option and pressing <Enter> lets you exit the Setup program without recording any new values or changing old ones.
39
PCI-6882 User Manual
40
CHAPTER
PCI SVGA Setup
Introduction
Installation of SVGA drivers
-for Windows 2000/XP
Further information
5
Chapter 5 PCI SVGA Setup
5.1 Introduction
The board has an onboard interface. The specifications and features are
described as follows:
5.1.1 Chipset
The PCI-6882 uses the Intel 852GME chipset for its graphic controller. It
supports dual independent LVDS LCD displays and/or conventional CRT
monitors.
5.1.2 Display memory
The 852GME chip with optimized Shared Memory Architecture, supports up to 64 MB frame buffer using system memory to provide LVDS
mode up to 1280 x 1024 @ 36 bpp with frequency range from 25 MHz to
112 MHz. The interface can drive CRT displays with resolutions up to
1920 x 1440 @ 60 Hz.
5.1.3 Display types
CRT and panel displays can be used simultaneously. The board can be set
in one of three configurations: on a CRT, on a flat panel display, or on
both simultaneously. The system is initially set to simultaneous display
mode. If you want to enable the CRT display only or the flat panel display
only, please contact Intel Corporation LTD., or our sales representative
for detailed information.
Notes:
Due to Intel not supporting Win98 and Windows ME, it is not recommended to install
Win98, Windows ME drivers on PCI-6882.
PCI-6882 User Manual
42
5.2 Installation of the SVGA Driver
Complete the following steps to install the SVGA driver. Follow the procedures in the flow chart that apply to the operating system that you are
using within your board.
Notes:
1. The windows illustrations in this chapter are
intended as examples only. Please follow the
listed steps, and pay attention to the instructions which appear on your screen.
2. For convenience, the CD-ROM drive is designated as "D" throughout this chapter.
5.2.1 Installation for Windows 2000/XP
To install an SVGA driver for Window 2000/XP, please run the setup
wizard "Intel Extreme Graphic 2" on the CD-ROM. An example installation is shown below:
1
1.
Select the path: D:\2_VGA, then double click "win2k_xp149" to
run "Install Shield Wizard"
43
Chapter 5
2.
Press the "Next" button.
3.
Press the "Next" button.
PCI-6882 User Manual
44
4.
In order to continue setup, you must accept the agreement, press the
"Yes" button and wait a minute.
5.
Choose the option "Yes, I want to restart my computer now." and
press the "Finish" button.
45
Chapter 5
5.3 Further Information
For further information about the AGP/VGA installation in your PCI6882, including driver updates, troubleshooting guides and FAQ lists,
visit the following web resources:
Intel website:
www.intel.com.
Advantech websites: www.advantech.com
www.advantech.com.tw
PCI-6882 User Manual
46
CHAPTER
6
PCI Bus Ethernet Interface
This chapter provides information on
Ethernet configuration.
• Introduction
• Installation of Ethernet drivers for
Windows XP
• Further information
Chapter 6 PCI Bus Ethernet Interface
6.1 Introduction
The board is equipped with a high performance 32-bit Ethernet chipset
which is fully compliant with 802.3u 100Base-T or 802.3z/ab 1000BaseT. It is supported by major network operating systems. It is also both
100Base-T and 10Base-T compatible.
The Ethernet port provides a standard RJ-45 jack. The network boot feature can be utilized by incorporating the boot ROM image files for the
appropriate network operating system. The boot ROM BIOS files are
combined with system BIOS, which can be enabled/disabled in the BIOS
setup.
6.2 Installation of Ethernet driver
Before installing the Ethernet driver, note the procedures below. Please
refer to the corresponding installation flow chart, then just follow the
steps described.
Note:
The windows illustrations in this chapter are
examples only. Follow the steps and pay attention to the instructions which appear on your
screen.
PCI-6882 User Manual
48
6.2.1 Installation for Windows XP
1.
Select “Ethernet Controller” from Device Manager.
2.
Select “Update Driver”.
49
Chapter 6
3.
Click the “Next” button.
4.
Click the “Next” button.
PCI-6882 User Manual
50
5.
Please choose “Continue Anyway”.
6.
Click the “Finish” button
51
Chapter 6
PCI-6882 User Manual
52
CHAPTER
7
Audio Setup
• Introduction
• Installation of audio driver for Windows XP
53
Chapter 7
Chapter 7 Audio Setup
7.1 Introduction
The PCI-6882 supports AC97 audio through the optional audio module
PCM-231A-00A1.
Notes
The audio function needs external AUDIO
board
e.g. PCM-231
7.2 Driver installation
7.2.1 Before you begin
Please read the instructions in this chapter carefully before you attempt
installation. The audio drivers for the PCI-6882 board are located on the
audio driver CD. Run the supplied SETUP program to install the drivers;
don't copy the files manually.
Note: The files on the software installation diskette are compressed. Do
not attempt to install the drivers by copying the files manually. You must
use the supplied SETUP program to install the drivers.
7.2.2 Windows XP driver
To install audio driver for Window XP, please run the setup wizard in CDROM. Example of installation is shown as below:
PCI-6882 User Manual
54
1. Select the path: D:\wdm_a357, then double click to run "Install Shield
Wizard".
2. Press the "Next" button and wait for a moment.
55
Chapter 7
3. Choose the option "Continue Anyway”.
4. Choose the option "Yes, I want to restart my computer now", then click
"Finish" button to reboot your computer.
PCI-6882 User Manual
56
Appendix
A
Programming DI/O &
Watchdog Timer
The board is equipped with a watchdog
timer that resets the CPU if processing
comes to a standstill for any reason.
This feature ensures system reliability
in industrial standalone or unmanned
environments.
Appendix A Programming DI/O & Watchdog Timer
A.1 Supported DI/O Register
Below are detailed description of the DI/O addresses and programming
sample.
A.1.1 DI/O Registers
GPIOBase port=480h
DI/O_SEL=GPIOBase + 34h
DI/O_SEL[8:1]-R/W
When set to a '1', the corresponding DI/O signal is programmed as an
input.
When set to a '0, the DI/O signal is programmed as an output.'
DI/O_LVL=GPIOBase + 38h
DI/O_LVL[8:1]-R/W
If DI/O [n] is programmed to be an output, then the corresponding
GP_LVL [n] bit can be updated by software to drive a high or low value
on the output pin. 1 = high, 0 = low.
If DI/O [n] is programmed as an input, then the corresponding GP_LVL
bit reflects the state of the input signal (1 = high, 0 = low). Writes will
have no effect.
PCI-6882 User Manual
58
A.1.2 DI/O Example program-1
-----------------------------------------------Set DI/O [5] as out ping, and out high.
-----------------------------------------------MOV DX,04B4h
;DI/O_SEL
MOV AL,DX
AND AL,11101111b
OUT DX,AL
MOV DX,04B8h
;DI/O_LVL
IN AL,DX
OR AL,00010000H
OUT DX,AL
A.2 Watchdog programming
In order to program the watchdog timer, you must write a program which
writes I/O port address 866 (hex). The output data is a value of time interval. The value range is from 01 (hex) to FF (hex), and the related time
interval is 1 sec. to 255 sec.
Data
00
01
02
03
04
FF
Time Interval
Disable
1 sec.
2 sec.
3 sec.
4 sec.
.
.
.
255 sec.
After data entry, your program must refresh the watchdog timer by
rewriting the I/O port 866 (hex) while simultaneously setting it.
When you want to disable the watchdog timer, your program
should write I/O port 866 (hex) to 00.
59
Appendix A
The following example shows how you might program the watchdog
timer in ASSEMBLY:
;Watchdog timer example program
MOV DX,866H
MOV AL, data ; data=1~255 Second
OUT DX, AL
PCI-6882 User Manual
60
Appendix
B
Pin Assignments
This appendix contains information of a
detailed or specialized nature. It includes:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Front Panel Connector
Floppy Connector
Secondary IDE Connector
Primary IDE Connector
Printer Connector
+12V Connector
USB port 0, 1
USB port 2, 3
DI/O Connector
D-SUB VGA Connector
AC’97 Interface Connector
LAN Connector
COM2 Connector
COM3, 4 Connector
COM1 Connector
LVDS Connector
IrDA Connector
TV-out Connector
AT Keyboard Connector
ATX Connector
LCD Backlight Connector
CompactFlash Connector
FAN Connector
SATA Connector
61
Appx. B
Appendix B Pin Assignments
B.1 Front Panel Connector (CN1)
9
7 5 3 1
10 8 6 4 2
Table B.1: Front Panel Connector (CN1)
Pin
Signal
Pin
Signal
1
3
5
7
9
+5V
+5V
SUSLED
RESET
POWER BUTTON
2
4
6
8
10
HDD_LED
GND
GND
GND
GND
PCI-6882 User Manual
62
B.2 Floppy Connector (CN2)
Table B.2: Floppy Connector (CN2)
Pin
Signal
1
GND
3
GND
5
GND
7
GND
9
GND
11
GND
13
GND
14
GND
17
GND
19
GND
21
GND
23
GND
25
GND
27
GND
29
GND
31
GND
33
GND
*low active
Pin
Signal
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
RWC#
NC
NC
Index#
MOA#
NC
DSA#
NC
DIR#
STEP#
WD#
WE#
Track0#
WP#
RDATA#
HEAD#
DSKCHG#
63
34
33
32
31
4
3
2
1
Appx. B
B.3 Secondary IDE Connector (CN3)
Table B.3: Secondary IDE Connector (CN3)
Pin
Signal
Pin
Signal
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
IDE RESET
D7
D6
D5
D4
D3
D2
D1
D0
GND
REQ
IOW
IOR
IOCHRDY
DACK
IRQ
A1
A0
HDCS1
HDLED
VCC
GND
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
GND
D8
D9
D10
D11
D12
D13
D14
D15
NC
GND
GND
GND
GND
GND
NC
NC
A2
HDCS2
GND
VCC
NC
PCI-6882 User Manual
64
1
2
3
4
41
42
43
44
B.4 Primary IDE Connector (CN4)
Table B.4: Primary IDE Connector (CN4)
Pin
Signal
Pin
Signal
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
RESET
D7
D6
D5
D4
D3
D2
D1
D0
GND
DREQ
IOW
IOR
IOCHRDY
DACK
IRQ
A1
A0
HDCS1
HDLED
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
GND
D8
D9
D10
D11
D12
D13
D14
D15
NC
GND
GND
GND
GND
GND
NC
NC
A2
HDCS2
GND
65
2
1
4
3
38
37
40
39
Appx. B
B.5 Printer Connector (CN5)
25 23
3 1
26 24
4 2
Table B.5: Printer Connector (CN5)
Pin
Signal
Pin
Signal
1
3
5
7
9
11
13
15
17
19
21
23
25
STB#
D0
D1
D2
D3
D4
D5
D6
D7
ACK#
BUSY
PE
SLCT
2
4
6
8
10
12
14
16
18
20
22
24
26
AFD#
ERR#
INIT#
SLIN
GND
GND
GND
GND
GND
GND
GND
GND
NC
PCI-6882 User Manual
66
B.6 +12V Connector (CN6)
2
4
1
3
Table B.6: +12V Connector (CN6)
Pin
Signal
1
2
3
4
GND
GND
+12 V
+12 V
B.7 USB port 0, 1(CN7)
10
9
8
6
7
5
4
3
2
1
Table B.7: USB port 0, 1 (CN7)
Pin
Signal
Pin
Signal
1
3
5
7
9
+5 V
USB0USB0+
USB GND
GND
2
4
6
8
10
+5 V
USB1USB1+
USB GND
NC
B.8 USB port 2, 3 (CN8)
10
9
8
6
7
5
4
3
2
1
Table B.8: USB port 2, 3 (CN8)
Pin
Signal
Pin
Signal
1
+5 V
2
+5 V
67
Appx. B
Table B.8: USB port 2, 3 (CN8)
Pin
Signal
Pin
Signal
3
5
7
9
USB2USB2+
USB GND
GND
4
6
8
10
USB3USB3+
USB GND
NC
B.9 DI/O Connector (CN9)
10
9
8
6
7
5
4
3
2
1
Table B.9: DI/O Connector (CN9)
Pin
Signal
Pin
Signal
1
3
5
7
9
DIO1
DIO2
DIO3
DIO4
GND
2
4
6
8
10
DIO5
DIO6
DIO7
DIO8
+5 V
PCI-6882 User Manual
68
B.10 VGA D-SUB Connector (CN10)
5
1
10
6
15
11
Table B.10: VGA D-SUB Connector (CN10)
Pin
Signal
Pin
Signal
1
2
3
4
5
6
7
8
R
G
B
NC
GND
GND
GND
GND
9
10
11
12
13
14
15
+5 V
GND
NC
S-DATA
HSYNC
VSYNC
S-CLK
B.11 AC’97 Interface Connector (CN11)
10
9
8
6
7
5
4
3
2
1
Table B.11: AC’97 Interface Connector (CN11)
Pin
Signal
Pin
Signal
1
3
5
7
9
+5 V
SDATA_IN
GND
SDATA_OUT
+5 V
2
4
6
8
10
BITCLK
GND
SYNC
RESET
SPEAK
69
Appx. B
B.12 LAN Connector (CN12)
1
8
Table B.12: LAN Connector (CN12)
Pin
Signal
Pin
Signal
1
2
3
4
TX+
TXRX+
NC
5
6
7
8
NC
RXNC
NC
B.13 COM2 (RS-232/422/485) (CN13)
13 11 9
7 5
3 1
14 12 10 8 6 4
2
Table B.13: COM2 connector (CN13)
Pin
Signal
Pin
Signal
1
3
5
7
9
11
13
DCD2
SIN2
SOUT2
DTR2
GND
TXD485+
RXD485+
2
4
6
8
10
12
14
DSR2
RTS2
CTS2
RI2
GND
TXD485RXD485-
PCI-6882 User Manual
70
B.14 COM 3, 4 Connector (CN14)
19 17
3 1
20 18
4 2
Table B.14: COM 3, 4 Connector (CN14)
Pin
Signal
Pin
Signal
1
3
5
7
9
11
13
15
17
19
DCD3
SIN3
SOUT3
DTR3
GND
DCD4
SIN4
SOUT4
DTR4
GND
2
4
6
8
10
12
14
16
18
20
DSR3
RTS3
CTS3
RI3
GND
DSR4
RTS4
CTS4
RI4
GND
B.15 COM1 Connector (CN15)
9 8 7 6
5 4 3 2 1
Table B.15: COM1 Connector (CN15)
Pin
Signal
Pin
Signal
1
2
3
4
5
DCD
SIN
SOUT
DTR
GND
6
7
8
9
DSR
RTS
CTS
RI
71
Appx. B
B.16 LVDS Connector (CN16)
Table B.16: LVDS Connector (CN16)
Pin
Signal
Pin
Signal
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
VCC_LCD
GND
VCC_LCD
LVDS0_N0
LVDS0_P0
GND
LVDS0_N1
LVDS0_P1
GND
LVDS0_N2
LVDS0_P2
GND
LVDS0_C0N
LVDS0_C0P
GND
LVDS_CLK
GND
LVDS0_N3
LVDSS0_P3
NC
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
VCC_LCD
GND
VCC_LCD
LVDS1_N0
LVDS1_P0
GND
LVDS1_N1
LVDS1_P1
GND
LVDS1_N2
LVDS1_P2
GND
LVDS1_C0N
LVDS1_C0P
GND
LVDS_DATA
GND
LVDS1_N3
LVDS1_P3
VCON
B.17 IrDA Connector (CN17)
1
2
3
Table B.17: IrDA Connector (CN17)
Pin
Signal
1
2
3
4
5
VCC
NC
IRRX
GND
IRTX
PCI-6882 User Manual
72
4
5
40
39
38
37
4
3
2
1
B.18 TV-out Connector (CN18)
1
2
3
4
5
Table B.18: TV-out Connector (CN18)
Pin
Signal
1
2
3
4
5
Y_OUT
C_OUT
GND
GND
CVBS_OUT
B.19 AT Keyboard Connector (CN19)
5
4
3
2
1
Table B.19: AT Keyboard Connector (CN19)
Pin
Signal
1
2
3
4
5
CLOCK
DATA
NC
GND
+5 V
73
Appx. B
B.20 ATX power Connector (CN21)
1
2
3
Table B.20: ATX power Connector (CN21)
Pin
Signal
1
2
3
5 VSB
NC
PS-ON
B.21 LCD backlight Connector (CN22)
5
4
3
2
1
Table B.21: LCD backlight Connector (CN22)
Pin
Signal
1
2
3
4
5
+12 V
GND
Back-light enable
NC
+5 V
PCI-6882 User Manual
74
B.22 CompactFlash Connector (CN23)
Table B.22: CompactFlash Connector (CN23)
Pin
Signal
Pin
Signal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
GND
D3
D4
D5
D6
CS1
#CE
A10
#OE
A9
A8
A7
VCC
A6
A5
A4
A3
A2
A1
A0
D0
D1
D2
IOCS16
#CD2
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
#CD1
D11
D12
D13
D14
D15
CS0
VS1
IOR
IOW
WE
IRQ
+5 V
CSEL
VS2
RESET
IORDY
DREQ
REG
DASP
PDIAG
D8
D9
D10
GND
75
Appx. B
B.23 FAN Connector (FAN1)
1
2
Table B.23: FAN Connector (FAN1)
Pin
Signal
1
2
3
FAN speed detect
+12 V
PWM
B.24 Serial ATA (SA1,SA2)
Table B.24: Serial ATA (SA1, SA2)
Pin
Signal
1
2
3
4
5
6
7
GND
TX+
TXGND
RXRX+
GND
PCI-6882 User Manual
76
3
77
Appx. B
PCI-6882 User Manual
78
Appendix
C
System Assignments
This appendix contains information of a
detailed nature. It includes:
•
•
•
•
System I/O ports
1st MB memory map
DMA channel assignments
Interrupt assignments
79
Appx. C
Appendix C System Assignments
C.1 System I/O Ports
Table C.1: System I/O ports
Addr. range (Hex)
Device
00-0F
20-21F
2E-2F
40-5F
60-6F
(60h)
(61h)
(64h)
70-77
78-7F
80
81-8F
90-91
92
93-9F
A0-A1H
C0-DF
E0-FF
100-1EF
170-178
1F0-1F8
200-20F
2E8-2EF
2F8-2FF
378-37F
3C0-3CF
3D0-3DF
3E8-3EF
3F0-3F7
3F8-3FF
778-77A
866
Master DMA controller
Master Interrupt controller
Configuration Index/Data
Timer/Counter
Keyboard controller
KBC Data
Misc Functions & Spkr Ctrl
KBC Command/Status
RTC/COMS/NMI-Disable
-available for system use-reserved-(debug port)
DMA Page Registers
-available for system useSystem Control
-available for system useSlave Interrupt Controller
Slave DMA Controller
-available for system use-available for system useSecondary IDE Control
Primary IDE Control
Game Port
COM4
COM2
Printer Port (Standard & AFF)
EGA
VGA
COM3
Floppy Controller
COM1
Printer Port (ECP Extensions) (Port 378+400)
Watchdog Timer
PCI-6882 User Manual
80
Table C.1: System I/O ports
Addr. range (Hex)
Device
CF8-CFB
CFC-CFF
D00-FFFF
PCI Configuration Address
PCI Configuration Data
-available for system use-
C.2 1st MB memory map
Table C.2: 1st MB memory map
Addr. range (Hex)
Device
F0000h - FFFFFh
*D0000h - EFFFFh
C0000h - CFFFFh
B8000h - BFFFFh
B0000h - B7FFFh
A0000h - AFFFFh
00000h - 9FFFFh
System ROM
Unused (reserved for Ethernet ROM)
Expansion ROM (for VGA BIOS)
CGA/EGA/VGA text
Unused
EGA/VGA graphics
Base memory
* If Ethernet boot ROM is disabled (Ethernet ROM occupies about 16 KB)
* E0000 - EFFFF is reserved for BIOS POST
C.3 DMA channel assignments
Table C.3: DMA channel assignments
Channel
Function
0
Available
1
Available (audio)
2
Floppy disk (8-bit transfer)
3
Available (printer port)
4
Cascade for DMA controller 1
5
Available
6
Available
7
Available
* Printer port ECP mode DMA select 1 or 3
81
Appx. C
C.4 Interrupt assignments
Table C.4: Interrupt assignments
Interrupt#
Interrupt source
IRQ 0
IRQ 1
IRQ 2
IRQ 3
IRQ 4
IRQ 5
IRQ 6
IRQ 7
IRQ 8
IRQ 9
IRQ 10
IRQ 11
IRQ 12
IRQ 13
IRQ 14
IRQ 15
Interval timer
Keyboard
Interrupt from controller 2 (cascade)
COM2
COM1
COM4
FDD
LPT1
RTC
Reserved (audio)
COM3
Reserved for PCI
PS/2 mouse
INT from co-processor
Primary IDE
Secondary IDE for CFC
PCI-6882 User Manual
82
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement