Poseidon2 4002 MANUAL
Poseidon2 4002
MANUAL
Poseidon2 4002 – Manual
www.HW-group.com
HW group
2
Poseidon2 4002 – Manual
HW group
Safety information
The device complies with regulations and industrial standards in force in the Czech Republic and the
European Union. The device has been tested and is supplied in working order. To keep the device in
this condition, it is necessary to adhere to the following safety and maintenance instructions.
Never remove the device cover if the relay terminals are connected to the electrical network!
Using the device in a manner other than prescribed by the manufacturer may cause its
safeguards to fail!
The power supply outlet or disconnection point must be freely accessible.
The device must not be used in particular under any of the following conditions:

The device is noticeably damaged

The device does not function properly

Unfastened parts can move inside the device

The device has been exposed to moisture or rain

The device has been serviced by unauthorized personnel

The power adapter or power supply cable are noticeably damaged

If the device is used in a manner other than designed for, the protection provided by the
device may fail.

The local electrical system must include a power switch or a circuit breaker and overcurrent
protection.
The manufacturer warrants the device only if it is powered by the supplied power adapter or an
approved power supply.
If you have any problems with installing or operating the device, please contact technical support:
HW group s.r.o.
http://www.hw-group.com
Email: [email protected]
U Pily 3
143 00 Praha 4
Czech Republic
Tel. +420 222 511 918
When contacting technical support, please keep at hand the exact type of your device (at the type
plate) and, if possible, the firmware version (see later in this manual).
www.HW-group.com
3
Poseidon2 4002 – Manual
HW group
POWER input
9-30V supply
RELAY OUTPUTS
Two 50V rated DT
relay contacts
DIGITAL INPUTS
Digital inputs 1–4
for dry contacts
POWER OUT
12V power output
for sensors
ETHERNET
10 or 100/10 Mbps
DIP switch
Configuration switches
Default is Off, Off
SENSORS 1-Wire/1-Wire UNI
Port1 to Port4 for connecting
1-Wire and 1-Wire UNI sensors
GSM MODEM
DIGITAL INPUTS
RS-232 port to
connect a modem
Inputs 5–12
for dry contacts
OUTPUTS
Two 50V rated DT
relay contacts
RS-485 Termination
RS-485 bus
Power Out
Activates termination
of the RS-485 bus
For genuine HW
group sensors
Power output for a GSM
modem or detectors
www.HW-group.com
4
Poseidon2 4002 – Manual
HW group
First steps
1) Connecting the cables






Turn the unit and note its MAC address that is printed on the label on the side.
Set the switches: DIP1=Off, DIP2=Off.
Connect Poseidon to Ethernet (patch cable to a switch, cross-over cable to a PC), RJ-45 port.
Plug the power adapter into a mains outlet and connect it to the Poseidon power jack.
The green POWER LED lights up.
If the Ethernet connection works properly, the LINK LED lights up after a short while, and then
flashes whenever data are transferred (activity indication).
2) Configuring the IP address – UDP Config
UDP Config utility – root directory of the supplied CD (Windows and Linux versions).
Available for download at www.HW-group.com Software > UDP Config.

Click the icon to launch UDP Config. The program automatically looks for connected
devices.

Automatic device discovery works only in the local network.

Individual Poseidon units are identified by their MAC addresses (on the label at the bottom).

Double-click a MAC address to open a basic device configuration dialog.
Double click for
details
www.HW-group.com
5
Poseidon2 4002 – Manual
HW group
First steps
Configure the network parameters

IP address / HTTP port (80 by default)

Network mask

Gateway IP address for your network

Device name (optional)
Click the Apply Changes button to save the
settings.
Alternatively, you may use the following utilities to configure the IP address:

UDP Config for Linux
Important:


To reset the device to factory defaults, toggle DIP1 several times within 5 seconds after
applying power to the device.
No configuration changes can be stored while DIP2=On.
To change the IP address, set DIP2=Off.
www.HW-group.com
6
Poseidon2 4002 – Manual
HW group
First steps
4) WWW interface of the device

To open the WWW interface of the device:
o
Enter the IP address into a web browser
o
Click the IP address in UDP Setup
Web interface of the device











General:
General Setup:
SNMP:
E-mail:
GSM:
Log & Time:
Portal:
Sensors:
Inputs:
Outputs:
System:
Overview of current readings
IP address, DNS, security (username/password)
SNMP / SNMP Trap configuration (ports and alarm recipients)
E-mail server, parameters, recipients, test
Local GSM modem / remote SMS-GW configuration
Time configuration, NTP server
Connection to a remote portal system
Device name, sensor names, status overview
Digital Input control, names, alarm parameters
Digital Output control, names, local mode
Firmware upgrade, save/restore configuration, etc.
DIP2 = ON
Configuration cannot be
changed over the network
User-defined names for digital
inputs and outputs
Alarm thresholds
Action when value
out of range
MIB file for SNMP
software
www.HW-group.com
7
Poseidon2 4002 – Manual
HW group
General Setup
Device name, e.g.
“First floor 1”
Three levels of passwords for
device security.
SNMP
5 destinations for SNMP Traps
www.HW-group.com
8
Poseidon2 4002 – Manual
HW group
E-mail
Inserts this text at the beginning
of the e-mail subject line
Up to 5 recipients
for alarm e-mails
Sends a test e-mail and
shows the connection log
E-mail test
result
Periodic Status Settings

Periodical Status
When on, sends an e-mail with device status at the specified intervals. For example
every 24 hours (1440 minutes).

Alarm reminder
When active, sends periodic reminders
that the device is in the Alarm state. For
example every 15 minutes.
To send e-mail, check:
1) Correct Gateway IP address
2) DNS server in network settings
3) SMTP server and port
4) Authentication turned on, correct
username and password
5) Spam filter for your mailbox is
disabled
NOTE:
Configuration changes must be confirmed by clicking the Apply Changes button.
www.HW-group.com
9
Poseidon2 4002 – Manual
HW group
GSM
To send text messages using a local GSM
modem (RS-232), select “GSM modem” and set
GSM function to “Local”.
IP address of “HWg-SMS-GW”
to use for sending text messages
(SMS)
Recipients' phone no's
Log & Time
Press the button to
synchronize time
Interval for logging
measured values
Expected size of recorded
data
Frequency of sending the
log file in e-mail
attachments
Opens the log file in the
browser as text
www.HW-group.com
10
Poseidon2 4002 – Manual
HW group
Portal
Message from the portal
Enable connection to the remote portal
Click to connect to the portal
AutoPush configuration
We recommend 2°C for temperature
and 5%RH for humidity.
Configures the communication with the portal using the HWg-Push protocol. Poseidon2 is the active
side and establishes the connection periodically and/or whenever a change in a sensor value
exceeds the configured AutoPush value.
The www.SensDesk.com portal connection parameters are pre-filled.
AutoPush configuration
Poseidon2 connects to the portal and notifies a value
change whenever a change in the sensor reading
exceeds the configured AutoPush value.
This configuration only applies to the communication
between Poseidon2 and the online portal. Local alarm
values are configured in the portal.
www.HW-group.com
For portal connection, check:
1) Correct Gateway IP address
2) DNS server in network settings
3) Correct Server Address of the
portal
11
Poseidon2 4002 – Manual
HW group
Sensors
Range of allowed values. If exceeded,
alarm is signaled.
Sends a SNMP trap if the
“Safe Range” for this sensor
is exceeded
Sends an E-mail if the
“Safe Range” for this sensor
is exceeded
Sends a text message (SMS)
if the “Safe Range”
for this sensor is exceeded
Sensor name will be shown in e-mails,
text messages, or SNMP traps
Scans connected sensors
and displays detected
sensors
After connecting sensors or changing RJ11 connections, sensors need to be detected again.
To avoid numerous false alerts (by e-mail
or SMS) whenever the reading fluctuates
around the threshold, you can use:
1) Hysteresis Idle Range
Tolerance band around the
“Safe Range”. Prevents
multiple alarm alerts.
2) Delay [s]
Delays the information about
alarm beginning and alarm
end by a specified time. Can be used for dry contacts, too.
Tip:
NOTE:
For details, see the complete “Poseidon2 family” manual.
Configuration changes must be confirmed by clicking the Apply Changes button.
www.HW-group.com
12
Poseidon2 4002 – Manual
HW group
Inputs
Enter Digital Input name,
will be shown in e-mails,
text messages or SNMP
traps
ALARM CONTACT STATUS:
Reaction to digital inputs:
 Active if On
Alarm when the contact
closes (1 = On)
 Disabled
 Active if Off
Alarm when the contact
opens (0 = Off)
 Send a SMS
 Send a SNMP Trap
 Send an E-mail
 Disabled
No Alarm
Connecting the inputs
FAQ

Poseidon2 informs about alarm
activation and deactivation for
each Digital Input and/or sensor.

E-mail format cannot be changed;
sensors may have custom names.

Yellow background in a line with a
sensor or an input means that the
safe range is exceeded but alarm
notification is off.
0 (Off)
1 (On)
TIP
• Poseidon family manual
For a detailed description of all settings and configuration tabs, see the
“Poseidon family” manual on the WEB or on the installation CD.
www.HW-group.com
13
Poseidon2 4002 – Manual
www.HW-group.com
HW group
14
Poseidon2 4002 – Manual
HW group
Outputs
Choose the output mode
Local Condition mode:
Manual mode:
Controls the outtput according
to the specified sensor
Output controlled over the WEB
or M2M protocols
Output mode:
A)
Manual
Output can be controlled using the Web interface or externally using M2M protocols.
The output cannot be used in “thermostat” mode – local condition.
B)
Local Condition
The output cannot be controlled over the Web, it is controlled by the local condition. The
output is read-only for all M2M protocols. Hysteresis in the sensor settings applies.
The output cannot be controlled remotely.
o
On if any alarm
The output is active if at least one input or sensor is in alarm.
o
On if value equal to Trigger
The output is active if the selected sensor reading is equal to the “Target Value”.
o
On if value higher than Trigger
The output is active if the selected sensor reading is greater than the “Target Value”.
o
On if value lower than Trigger
The output is active if the selected sensor reading is less than the “Target Value”.
o
Dependent On – sensor / input to which the condition applies.
www.HW-group.com
15
Poseidon2 4002 – Manual
HW group
System
Protocols and timeout for the
communication monitor
Loads the configuration XML file to
Poseidon2 from the PC
Uploads new firmware from
the PC
Configuration
Communication Monitor

Download – Retrieve the configuration from the
device and store it on the PC.
This function controls a virtual Digital Input
that is available in Inputs as “Com Monitor
1” with an ID of 123.

Upload – Restore a configuration from the PC to the
device.
If no communication took place in the
specified time using the selected protocols,
it sets “Com Monitor 1” = 0 (Off).
System

Restart Device – Reset the device over the WEB
interface.

Set Default Config – Restore factory-default settings.

Upgrade FW – Upload new firmware to the device.
NOTE:
This function is useful e.g. to send a warning
e-mail whenever Poseidon2 ceases to be
periodically monitored over SNMP or
SCADA.
Configuration changes must be confirmed by clicking the Apply Changes button.
www.HW-group.com
16
Poseidon2 4002 – Manual
HW group
Software Applications
HWg-PDMS
Windows application that logs
data from all HW group devices
into its internal database.
The application runs in the
background (NTservice). Data are
retrieved from the device over
http or e-mail.
Data can be exported over XML
or automatically stored to MS
Excel.
License:
Free HWg-PDMS version for 3 sensors
Paid versions for 8 / 20 / 200 / unlimited sensors
HWg-Trigger
Windows application for detecting and reacting
to events.
Detects, for instance, disconnected devices,
failed sensors values out of range, or incoming
SNMP Trap alerts.
Possible responses include sending an
e-mail, activating a relay over the
network, or sending a text message
(SMS) using HWg-SMS-GW.
Other responses include displaying a
warning message in Windows,
starting an application, or
shutting down the computer.
License:
30-day trial version free of charge
www.HW-group.com
17
Poseidon2 4002 – Manual
HW group
PosDamIO
Poseidon Damocles I/O is a command-line utility for Windows and Linux that lets
you control Poseidon and Damocles units over the XML interface. It can display the
states of sensors, inputs and outputs, as well as set an output high or low.
SensDesk.com
Online portal for collecting data from LAN and GSM sensors.
Poseidon2 can connect to the SensDesk internet service. All devices can be managed from a single
WWW interface. Watch sensor states, display your devices in a map, compare trends in time and
analyze alarm messages.
SensDesk is a way to implement fully functional monitoring of customer technology in a matter of
minutes, with fixed costs of the system. No need for installing a complex system or adding another
server at the customer side.
 Overview of all sensors at a single place
 Centralized alarm configuration for individual sensors
 Mobile application for monitoring
 Remote configuration of GSM devices
www.SensDesk.com
www.HW-group.com
18
Poseidon2 4002 – Manual
HW group
Specifications
OVERVIEW
LAN interface
Supported protocols
SNMP compatibility
Internal Logger
RJ45 (100BASE-Tx) – 10/100 Mbps network compatible
IP: ARP, TCP/IP (HTTP, NTP, SMTP, netGSM, HWg-PUSH), UDP/IP (SNMP)
Ver.1.00 compatible, partial ver.2.0 implementation
250,000 records in flash memory (logged items: Sensors, DI, DO)
SENSORS 1-Wire
Type
Active ports / distance
Sensors
HW group original accessories: 1-Wire & 1-Wire UNI
6xRJ11, max distance 60m per each RJ11 active port
Up to 16 sensors in total (temperature + humidity combo sensors count as 2 sensors)
SENSORS RS-485
Type
Connector / distance
Sensors
HWg original accessories
RJ45 + 2x DIP for termination / Max distance 1000m
Up to 26 sensors in total (temperature + humidity combo sensors count as 2 sensors)
DI (Digital Inputs for Dry Contacts)
Port / type
IN1-IN12 / Digital Input (supports NO/NC Dry contact)
Sensitivity
1 (On) = 0-500 Ω (Max. distance up to 50m)
DO - OUTPUTS
Port / type
Max. voltage / load
State
OUT1 - OUT4 / Relay contacts (NC-COM-NO)
60V AC/DC, Max 1A, up to 60VA/24W ( 0.5A/48V)
Power up state (no state restart memory)
RS-232 interface
External GSM modem
Connect external GSM modem
POWER input
Port
Power input
POWER 9-30V DC
9-30V DC / 2,5W (typically 250 mA)
Connectors: Jack (barrel, inner 2.1 mm outer 5.1 mm) + Terminal Block
POWER output
Voltage
Current / Connector
Power Out = Power IN (9–30V)
Max. 150mA / Terminal Block
LED status indicators
POWER (RJ45 + top)
LINK & Activity (RJ45)
Setup / Alarm
Inputs / Outputs
Green – power OK (top), Ethernet enabled (RJ45)
Yellow - Ethernet connectivity
Red
Green / Yellow
DIP SWITCH
DIP1: Setup
DIP2: Security
Physical parameters
Temperature range
Dimensions / Weigh
EMC
www.HW-group.com
OFF = Normal state
Load defaults: Set ON, power-up device, toggle 3 times during first 5 seconds
ON = Secure mode (online demo) – remote configuration disabled
OFF = Non-secure mode – remote configuration enabled
Operating: -30 to +85 °C (-22 to +185 °F) / Storage: -35 to +85 °C (-31 to +185 °F)
100 x 213 x 35 [mm] / 225 g
FCC Part 15, Class B, CE - EN 55022, EN 55024, EN 61000
19
Poseidon2 4002 – Manual
HW group
Dimensions
www.HW-group.com
20
Poseidon2 4002 – Manual
HW group
Power output
Poseidon2 4002 features the PWR OUT terminals for powering connected
sensors and detectors. For example a smoke detector.
PWR OUT voltage is the same as the Poseidon2 4002 supply voltage!
Relay outputs
NO
COM
POWER OUT
12V
NO NC
+
-

NO and NC labels apply to Off (0) state, or device turned off

When the output is On (1), a “Normally Open” (NO) relay contact is closed

LEDs: Contact state (closed / open) is indicated by a LED

Isolation: The double-throw contact is electrically isolated from the rest of the device

ID range: Outputs use ID addresses from 151 to 180
Inputs – Digital (dry contact) inputs
Digital input terminals may be connected to voltage-free contacts or the GND pin. The inputs are
electrically connected to the 12V power supply. Never connect the inputs to the 48V supply voltage!

Unconnected inputs read as “0 (Off)”

Active inputs read as “1 (On)”



Supported sensors: Any contact without external voltage (dry contact)
Polling period: 800 ms
Range of sensor IDs: Inputs use ID addresses
from 1 to 24
www.HW-group.com
21
Poseidon2 4002 – Manual
HW group
M2M interface
The product is ready to be connected with third-party SW applications.
For a description of the interfaces (XML format, detailed SNMP description, mapping of Modbus/TCP
variables), see the detailed “Poseidon family” manual.

XML (over HTTP)

SNMP , SNMP traps

Modbus/TCP

SMTP (E-mail)
TIP
• For a detailed description of the M2M communication interface and other
details, see the detailed Poseidon family manual.
SDK (Software Development Kit)
Programmers can take advantage of the HWg SDK (Software Development Kit) with ActiveX
interface and ready-made examples.

VB - Visual
examples)

Borland C++ (1xx examples)

Microsoft Visual C++ (2xx examples)

C# / .NET (5xx examples)

Borland Delphi (4xx examples)

JAVA

PHP / ASP

other examples that do not directly
use SDK functions (all 9xx examples)
Note:
www.HW-group.com
Basic
(6.0)
- (3xx
The latest version of HWg-SDK is available for download at the HWg website.
You just need to register your e-mail.
22
Poseidon2 4002 – Manual
HW group
Updating the firmware over the WEB
Upload the .hwg firmware file over http to http://x.x.x.x/upload/.
Connection problems must be avoided during file transfer.
Firmware in the .HWg format is available at our website, or on the supplied CD.
Restoring factory defaults
To restore the factory default configuration (including deleting all passwords):
1) Turn the device off by disconnecting power.
2) Set DIP1 to ON.
3) Turn the device on.
4) Toggle DIP1 several times during the first 5 seconds after powering up.
TIP
• For a detailed product description, see the detailed Poseidon family manual.
www.HW-group.com
23
Poseidon2 4002 – Manual
www.HW-group.com
HW group
24
Poseidon2 4002 – Manual
HW group
Mounting on a wall
Mounting on a DIN rail
Contact
HW group s.r.o
Rumunská 26 / 122
Praha 2, 120 00, Czech republic
Tel. +420 222 511 918
Fax.
+420 222 513 833
http://www.HW-group.com
www.HW-group.com
25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement