Cat Eliminator Slip
Installation Instructions
1. Make sure the bike is completely cool before starting the
installation. Make sure the bike is secure on a centerstand
or ideally a service lift.
8. Install the TBR muffler assembly and attach using OEM
mounting hardware.
2. Remove rear passenger seat and tail cover.
V.A.L.E.
TM
2011-2016 Kawasaki
V A R I A B L E
A X I S
L O C K I N G
E X H A U S T
ZX-10R
3. Remove main seat.
4. Remove exhaust valve cables from servo under seat. Place
a wrench around servo so it does not move.
V.A.L.E.™ Slip-on Exhaust System with M-2 Canister
Part # 005-2990406V, 005-2990407V, 005-2990408V
9. Check alignment and tighten muffler and the 4 6x20mm
V.A.L.E.™ S.H.C.S.
5. Remove OEM muffler assembly with servo cables.
10. Tighten barrel clamp.
Parts List
Qty. Description
1
Muffler Canister
1
Slip-on Tube 1
HARDWARE KIT
2
X-Ring (half)
1
Barrel Clamp
4
6x20mm Socket Head Cap Screw
4
6mm Split Lock Washer
1
5mm Long Handle Ball End Hex Wrench
1
T20 Torx Screw Hex Wrench
1
TBR Sticker Kit
1
Adaptor Kit
Part Number
005-187-207
005-29904S
005-299-3
6. Attach TBR muffler to slip-on tube using the 4 6x20mm
S.H.C.S. and lock washers provided. Leave loose for now.
005-7-2-4
005-27-66MSH
005-SH620
005-WL6
005-9-18610
005-9-15820
015-10212
11. Re-install seats and covers.
12. Double check all your work.
005-92-22KIT
IMPORTANT - PLEASE READ CAREFULLY
We recommend that this performance part be installed by a qualified
motorcycle technician. If you have any doubts as to your ability to install
this performance part, please consult with your local motorcycle dealer.
Read all instructions first before starting installation. Make sure the
motorcycle and exhaust system are completely cool before starting the
installation. Also, make sure the bike is secure on a centerstand or ideally
a service lift during installation. Be sure to save all stock components for
possible use later.
7. Slide supplied barrel clamp on end of slip tube where it
will meet OEM headpipe.
13. Before you run the bike, clean off all fingerprints and
dirt, as any oily residue will etch the metal and become
somewhat permanent when the system gets hot. Also,
remove any plastic film from the name badge(s) and or
canister clamp(s). Run the bike and enjoy. It is normal for
some white smoke to appear the first time you start the
bike. This is packing/manufacturing oil from inside the pipe
burning off. Check for gaps or leaks. If you find a leak, a
little high temperature silicon sealant should fix it. After 50
to 100 miles, recheck all fasteners for tightness.
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue after a few heat cycles, this is a normal characteristic of high quality stainless steel. Clean
using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Titanium Header System: Polished titanium pipes will experience color shift ranging from deep blue/purple through amber after a few heat cycles. This is a normal characteristic
of high quality titanium. Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
V.A.L.E.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the bright finish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
TM
2011-2016 Kawasaki
V A R I A B L E
A X I S
L O C K I N G
E X H A U S T
ZX-10R
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside is in
good condition and not burned out, as exhaust heat inside an empty canister will deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include everything you need to easily do it yourself.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside is in
good condition and not burned out, as exhaust heat inside an empty canister will deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include everything you need to easily do it yourself.
V.A.L.E.™ Slip-on Exhaust System with M-2 Canister
Part # 005-2990406V, 005-2990407V, 005-2990408V
Repack all road canisters at the first signs of packing material deterioration. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the intense heat and lack of cooling air can quickly burn through the canister material. Two Brothers
Racing does not provide a warranty for burned canisters.
Qty. Description
1
Muffler Canister
1
Slip-on Tube 1
HARDWARE KIT
2
X-Ring (half)
1
Barrel Clamp
4
6x20mm Socket Head Cap Screw
4
6mm Split Lock Washer
1
5mm Long Handle Ball End Hex Wrench
1
T20 Torx Screw Hex Wrench
1
TBR Sticker Kit
1
Adaptor Kit
Part Number
005-187-207
005-29904S
005-299-3
005-7-2-4
005-27-66MSH
005-SH620
005-WL6
005-9-18610
005-9-15820
015-10212
005-92-22KIT
Warranty
Two Brothers Racing products are intended for closed course competition purposes only, and therefore are sold “as is”
without warranty. Two Brothers Racing specifically disclaims any warranties of merchantability or fitness for a particular
purpose and disclaims all responsibility for consequential and incidental damages or any other losses arising from the use
of these products or parts.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement