Owner's Manual 
Triumph™
Child Restraint System
Owner’s Manual
Keep for future use
Rear-facing
2.3 to 18 kg
(5 to 40 lb.)
48 to 94 cm
(19 to 37 in.)
Forward-facing
10 to 29.4 kg
(22 to 65 lb.)
71 to 127 cm
(28 to 50 in.)
Para instrucciones en Español,
llamar al: 1-800-233-5921
WARNING:
To reduce the risk of serious injury
or death, read this owner’s manual prior
to installing and using this child restraint.
© 2014 Evenflo Company
25706664
9/14
More children are killed every year as passengers
in car crashes than by any other type of injury. To
reduce the risk of SERIOUS INJURY or DEATH, read this
owner’s manual and your vehicle owner’s manual before
installing and using this child restraint. Using a child restraint
makes a big difference. By properly using this child restraint
and following these instructions (and the instructions that
accompany your vehicle), you will greatly reduce the risk of
serious injury or death to your child from a crash. Do not be
misled by the commonly used term “safety seat;” no restraint
system can prevent all injuries in all crashes. Many properly
restrained adults and children are injured in motor vehicle
crashes, including relatively minor crashes. A properly used
child restraint is the best way to minimize injuries to your child
and to increase the chances for your child’s survival in most
crashes.
Table of Contents
Important Notice ................................................................... 1
Warnings ............................................................................... 2
Safe Practices ......................................................................... 8
Recall Information for U.S. Customers .................................... 9
Public Notice for Canadian Customers ................................... 9
Motor Vehicle/Aircraft Usage ................................................. 9
LATCH Information .............................................................. 10
Symbol Legend.................................................................... 10
Storing Your Instructions ...................................................... 10
Visual Glossary ..................................................................... 12
Using the Triumph Rear-facing .................................. 14
Rear-facing Installation Using the Vehicle Seat Belt ............... 16
Rear-facing Installation Using Lower Anchor
Connector Assembly ......................................................... 20
Using the Triumph Forward-facing ............................ 24
Forward-facing Installation Using the Vehicle Seat Belt ......... 26
Forward-facing Installation Using Lower Anchor
Connector Assembly ......................................................... 32
Securing Your Child in the Child Restraint ............................ 37
Adjusting the Crotch Strap .................................................. 39
Removing Child from the Restraint ...................................... 40
Removing the Lower Anchor Connector Assembly ............... 41
Removing the Tether Strap .................................................. 42
Removing the Seat Pad ........................................................ 43
Installing the Seat Pad ......................................................... 44
Installing the Accessories.......................................................46
Removing the Adjustable Headrest .......................................48
Care and Cleaning ................................................................49
Securing Your Child Restraint in Aircraft ................................50
Replacement Parts ............................................................... 55
Limited Warranty ................................................................. 56
U.S. REGULATORY NOTICE
This child restraint meets all applicable requirements of
Federal Motor Vehicle Safety Standard 213.
CANADIAN REGULATORY NOTICE
(Model numbers ending in “C.”)
This child restraint meets all applicable requirements of
Canadian Motor Vehicle Safety Standards CMVSS 213
and 213.1.
Child Requirements
• No restraint can guarantee absolute protection from
injury in every crash.
• This child restraint is designed for use by children in
rear-facing and forward-facing positions. To use this
child restraint properly, children MUST meet weight/size
specifications as follows:
For Rear-facing Use
• The child weighs 2.3 – 18 kg (5 – 40 lb.)
• The child is 48 – 94 cm (19 – 37 inches) AND the top
of child’s head is at least 25 mm (1 in.) below the top of
the child restraint seat back.
DO NOT use this or any child restraint with a
premature infant until after consulting your doctor.
Premature infants may have difficulty breathing when in
a sitting position.
The American Academy of Pediatrics recommends that
children ride in the rear-facing position to the highest
weight or height allowed by the child restraint.
Note: Once your child exceeds 18 kg (40 lb.) OR the
top of their head is within 25 mm (1 inch) of the
top of the child restraint seat back, they MUST use
this child restraint in the forward-facing position.
For Forward-facing Use
• The child weighs 10 – 29.4 kg (22 – 65 lb.)
• The child is 71 – 127 cm (28 – 50 in.)
• Child is one year old or older
Note: Once your child exceeds 29.4 kg (65 lb.) OR is
taller than 127 cm (50 in.), they can no
longer safely use this child restraint, and you should
consider using a booster seat.
1
WARNING
WARNING
Air Bag Warning
• DO NOT use this child restraint in the front seat of a
vehicle equipped with an air bag, unless the air bag has
been deactivated. Interaction between a rear-facing
restraint and air bags may cause serious injury or death.
Air bags may cause serious injury or death to children 12
years of age and under. If your vehicle has an air bag,
refer to your vehicle owner’s manual for child restraint
installation.
• If the rear seat of your vehicle is equipped with side
air bags, refer to the following information for proper
usage:
Vehicles built prior to the 2002 model year:
DO NOT use this restraint in a vehicle seating position
equipped with a side air bag unless authorized by the
vehicle manufacturer.
Model year 2002 and newer vehicles:
Refer to your vehicle owner’s manual before placing this
restraint in a seating position equipped with a side air
bag.
• DO NOT place any objects between the restraint and
the side air bag, as an expanding air bag may cause the
items to strike your child.
Location Warnings
• According to statistics, children are safer when properly
restrained in a rear seating position than in the front
seating position. Generally, the center rear position is
safest and should be used if available. Children 12 and
under should ride in the back seat of the vehicle.
• ONLY use this child restraint on forward-facing vehicle
seats. DO NOT use this restraint with vehicle seats that
face the rear or side.
• ONLY use this child restraint on vehicle seats with backs
that lock into place.
• Some child restraints do not fit all vehicles or all seating
locations. There are many thousands of combinations of
vehicle makes, models, child restraint configurations, seat
belt designs and seat cushion shapes.
The easiest way to determine whether your child restraint
is suitable for a particular seating position is to check for a
tight installation. If the child restraint can not be properly
installed, DO NOT use the child restraint. Consult vehicle
owner’s manual, try a
different seating location or call Evenflo.
Premature Infants
• DO NOT use this or any child restraint with a premature
infant until after consulting your doctor. Premature infants
may have difficulty breathing when in a sitting position.
Rear-facing Warnings
• DO NOT use this child restraint rear facing in a vehicle
equipped with lap belts that only lock during a sudden
stop or crash (emergency locking retractors). You must
use a seating location with a locking seat belt. Check your
vehicle owner’s manual to see if you have lap belts with
emergency locking retractors.
• When using this restraint rear-facing, DO NOT loosen
the vehicle seat belt to provide more leg room as this will
prevent the child restraint from protecting your child.
• Fold-down armrests could pose a hazard to a rearfacing child in certain types of collisions. Consult your
vehicle owner’s manual before installing any rearfacing child restraint in front of a fold-down armrest.
• NEVER turn a child restraint forward-facing with an
infant weighing less than 10 kg (22 lb.) or less than one
year of age, crash forces may cause serious injury
or death.
2
3
WARNING
WARNING
• The headrest on the vehicle seat that the child faces when
sitting in the rear facing mode should be placed in the
lowest position. The vehicle seat back that the child faces
must be fully padded and free of any hard objects.
Forward-facing Warnings
• If your child weighs more than 29.4 kg (65 lb.) or their
shoulders are above the highest harness level, you MUST
discontinue using this child restraint as it may no longer
adequately protect your child.
Seat Belt Warnings
• DO NOT use this child restraint in a vehicle with doormounted seat belts.
• DO NOT use this child restraint in a vehicle with seat
belts that automatically move along the vehicle frame
when the door is opened. These seat belts will not hold a
child restraint properly.
• Use only with vehicle seat belts that can be pulled tight
and will stay locked.
• DO NOT use this child restraint if it moves more than
25 mm (1 inch) side to side or front to back at the
vehicle belt path. Serious injury or death may result from
poor installation. If you can not tightly secure the child
restraint, try again or move it to another location.
• If the vehicle seat belts are not routed and fastened
correctly, the child restraint may not protect your child
in a crash.
• DO NOT allow the seat belt release button to touch the
child restraint. Accidental contact may cause the seat belt
to release. If necessary, turn the seat belt release button
away from the child restraint or move the child restraint
to a different location.
• Failure to adjust the harness or seat belts snugly around
your child may result in your child striking the vehicle’s
interior during a sudden stop or crash.
Serious injury or death may occur.
LATCH Warnings
• The LATCH system is intended to be used ONLY as
described in these instructions. Serious injury or death
may result from misuse. LATCH (Lower Anchors and
Tethers for CHildren) is a system for attaching the child
restraint to your vehicle seat. It can be used in place of
the seat belts in vehicles with vehicle lower anchor bars.
Refer to your vehicle owner’s manual for the locations of
the vehicle lower anchor bars. Note: Your vehicle owner’s
manual may refer to this system as “Universal Anchorage
System,” “Lower Universal Anchorage System,”
or “ISOFIX.”
• DO NOT use the lower anchors of the child restraint
anchorage system (LATCH system) to attach this child
restraint when restraining a child weighing more than
22.7 kg (50 lb.) with the internal harnesses of the child
restraint.
• ONLY use for securing child restraint to vehicle lower
anchor bars.
• ALWAYS read and follow exactly the instructions that
accompany your vehicle and child restraint.
• NEVER attach two lower anchor connectors to one
vehicle lower anchor bar.
• DO NOT use the vehicle seat belts to install a child
restraint when using the lower anchor connector
assembly. Using both together can cause slack in a
sudden stop or crash.
• ALWAYS be sure that the lower anchor connectors are
fully engaged onto the vehicle lower anchor bars by
pulling hard on the lower anchor straps. If they are not
fully engaged, the lower anchor connector assembly will
not secure your child restraint. Serious injury or death
may result.
• DO NOT use this child restraint if it moves more than
25 mm (1 inch) side to side or front to back at either
the rear-facing or forward-facing belt path on the child
restraint. Serious injury or death may result from poor
installation. If you can not tightly secure the child
restraint, try again or move it to another location.
• To avoid a strangulation hazard, you MUST store the
unused lower anchor connector assembly strap, with all
slack removed, in storage area on the back of the seat.
Roll or fold excess lower anchor connector assembly strap
and secure with a rubber band to prevent serious injury to
vehicle occupants.
4
5
WARNING
• In addition to these instructions, read and follow your
vehicle owner’s manual regarding installation of the child
restraint and LATCH. If there is a discrepancy,
follow your vehicle owner’s manual.
Top Tether Warnings
• Top tether strap is for forward-facing ONLY.
• Failure to secure the top tether strap (provided) as
specified in these instructions could result in serious injury.
• The top tether strap MUST be used if your vehicle has
a plain lap belt that only locks during a sudden stop or
crash (emergency locking retractors) AND/OR if your
vehicle has seat belts whose buckles extend from a slot
in the vehicle seat cushion in front of the crease where
the seat and back cushions meet. Otherwise the child
restraint cannot be installed tightly, increasing the risk of
injury to your child. Check your vehicle owner’s manual to
see if your vehicle has emergency locking retractors.
• To avoid a strangulation hazard, you MUST tightly roll or
fold excess tether strap and secure with the strap/rubber
band. Attach the tether hook to the storage clip when
not in use. This will keep an unused tether from hitting
someone during a crash.
Additional Warnings
• DO NOT use child restraint if it is damaged, broken, or
missing parts.
• DO NOT use this restraint if it has been involved in a
crash. It must be replaced.
• NEVER leave child unattended.
• DO NOT remove back cover.
• This child restraint must be securely belted to the vehicle
at all times with the vehicle seat belt or lower anchor
connector assembly and tether strap (if available). An
unsecured child restraint may injure someone if a crash
occurs.
• DO NOT attach additional padding, toys, or other
devices not made by Evenflo to the child restraint. Items
not tested with the child restraint could injure the child.
6
WARNING
• Failure to follow installation instructions could result
in serious injury or death. These instructions and the
instructions in your vehicle owner’s manual must be
followed carefully. If there is a conflict between the two,
the vehicle owner’s manual regarding child
restraint installation must be followed.
• In hot or sunny weather, ALWAYS check the seat, buckle
and lower anchor connectors, and adjuster for hot areas
before placing a child into the child restraint. The child
could be burned. Cover the child restraint with a light
colored blanket when you leave the
vehicle.
• In cold weather, DO NOT dress the child in bulky
clothing like snowsuits if the child is riding in a child
restraint. Bulky coats/snowsuits make it difficult to
properly tighten the harness to the child which may
allow the child to be ejected from the restraint during a
crash. If necessary, place a blanket over the
harnessed child without interfering with the child restraint
harness system.
• Children have STRANGLED in loose or partially
buckled harness straps. Fully restrain the child.
WARNING
Children have STRANGLED
in loose or partially buckled
harness straps. Fully restrain
the child.
7
Safe Practices
Recall Information for U.S. Customers
• Everyone rides buckled up or the vehicle does not
go. Make no exceptions for adults or children. If someone
unbuckles, stop the vehicle. Being firm and consistent
from the start will mean fewer discipline problems as
children get older. An unrestrained person can be thrown
into and injure other passengers.
• Many safety advocates and healthcare professionals
recommend that children ride rear facing for as long as
possible. See limitations recommended on page 1.
• NEVER try to tend to a crying baby’s needs while driving.
NEVER take a baby out of a child restraint for comforting
while the vehicle is moving.
• DO NOT allow a child in a vehicle to have objects such
as lollipops or ice cream on a stick. The object can injure
the child if the vehicle swerves or hits a bump.
• DO NOT feed an infant who is riding in a child restraint.
• Put sharp or heavy items in the trunk. Anything loose can
be deadly in a crash.
• For child restraints equipped with leather seat pads, cover
your seat with a blanket in warm weather. Leather can
become very hot in direct sunlight.
• Child restraints could be recalled for safety reasons.
You must register this restraint to be reached in a
recall. Send your name, address, the restraint’s model
number, and manufacturing date to:
Evenflo Company, Inc., 1801 Commerce Dr.,
Piqua, OH 45356, or call 1-800-233-5921.
You may also register on-line at:
www.evenflo.com/registercarseat
• For recall information call the U.S. Government’s
Vehicle Safety Hotline at 1-888-327-4236 (TTY:1-800424-9153), or go to http://www.NHTSA.gov.
Public Notice for Canadian Customers
• Child restraints could be recalled for safety reasons.
You must register this restraint to be reached in a recall.
Send your name, address, and the restraint’s model
number and manufacturing date to:
Evenflo Company, Inc., 1801 Commerce Dr.,
Piqua, OH 45356, call 1-937-773-3971,
or register online at:
www.evenflo.com/registercarseatcanada
• For public notice information, call Transport Canada at
1-800-333-0510 (1-613-993-9851 in Ottawa region).
Motor Vehicle/Aircraft Usage
When used with the internal
harness and properly installed
pursuant to these instructions,
this restraint is certified for use only
in passenger and multi-purpose
passenger motor vehicles, buses, and
Check with
your airline before
trucks equipped with Type I or II seat
departure to make sure
belts and in aircraft.
TIP
IP!!
this restraint meets
8
Airplane installation is the same as
their requirements.
Type I vehicle installation. Turn the
top of the airplane seat belt buckle
away from the restraint for easy
release and removal.
Refer to pages 50 to 54 for instructions on installing your
child restraint in aircraft.
9
LATCH Information
This page is intentionally blank.
“LATCH” (Lower Anchors and Tethers for CHildren) is a
system for attaching the child restraint to your vehicle seat.
It can be used in place of the seat belts in vehicles with
LATCH anchors. Refer to your vehicle owner’s manual for
the locations of LATCH anchors.
Note: Your vehicle owner’s manual may refer to this system
as “Universal Anchorage System,” “Lower Universal
Anchorage System,”or ”ISOFIX.”
Symbol Legend
Air Bag Symbol – Alerts you to important
information about air bag safety.
LATCH Symbol – Alerts you to important
information about LATCH safety.
Tether Anchor Symbol – Alerts you to
important information about tether anchor safety.
Storing Your Instructions
After thoroughly reading
and
Symphony 65
following these instructions,
Child Restraint System
store the instructions
on the
Owner’s Manual
back of the seat.
™
Keep for future use.
Rear-facing
2.3 to 18 kg
(5 to 40 lbs)
48 to 94 cm
(19 to 37 in.)
Forward-facing
For future reference, record the model number
of your child
restraint AND the date of manufacture below.
10 to 29.4 kg
(22 to 65 lbs)
71 to 127 cm
(28 to 50 in.)
Booster
Model Number:
18 to 49.8 kg
(40 to 110 lbs)
110 to 145 cm
(43.3 to 57 in.)
Date of Manufacture:
10
Para instrucciones en Español,
llamar al: 1-800-233-5921.
WARNING:
To reduce the risk of serious injury
or death, read this owner’s manual prior
to installing and using this child restraint.
© 2013 Evenflo Company, Inc.
25700938
2/13
11
Visual Glossary
Visual Glossary
Your vehicle components may be significantly different than
pictured. Consult your owner’s manual to help you identify
your vehicle components.
Front Seat Lap
and Shoulder Belts
Fold-down Armrest
Consult your vehicle’s owners manual.
Tether Anchors
Forward-facing
ONLY
Rear
Headrests
Front
Headrests
Back Seat
Belt Buckles
10
Back Seat
Retractor
4
30
20
12
0
Center Lap
Belt
A
Lap/Shoulder
Belt
IR
B
A
G
Important
Vehicle Lower
Anchor Bars
Seat Crease
Front Seat Retractor
IMPORTANT: If your vehicle has side air bags, please refer to
the warnings on page 2.
Front View
Adjustable
Headrest
(Optional)
Harness Tabs
Seat Pad
Harness Straps
Consult your vehicle
owner’s manual to determine
proper placement of child restraint
in your vehicle and familiarize
yourself with your vehicle’s
components.
Back View
Tether Strap
and Hook
Chest Clip
Buckle Tongue
Holders
(not available on
Cup Holder
(Optional)
all models)
Cup Holder
(Optional)
BeltTrac
Access Flap
TensionRight™
Tightening
Knob
Buckle
Crotch Strap
Tension
Release Button
ReclineRight™
Lever
12
Lower Anchor
Connector
Assembly
Lower Anchor
Connector
Assembly
Base
13
Using the Triumph™
Rear-facing
• Weight: 2.3 to 18 kg (5 to 40 lb.)
• Height: 48 to 94 cm (19 to 37 in.). Top of the head is
least 25 mm (1 in.) below the top of the child restraint
seat back.
25 mm (1 inch)
or more
WARNING
When using this restraint rear-facing, DO NOT loosen
the vehicle seat belt to provide more leg room as this will
prevent the child restraint from protecting your child.
1. Secure child restraint to the vehicle seat.
• Child restraint is in Position #1 (page 16).
• Install with vehicle seat belt (page 16) or lower
anchor connector assembly (page 20).
• Install locking clip, if necessary (page 18).
• Towel rolled up and placed beneath the base, if
necessary (page 16).
2. Set the child in the child restraint.
Top of head is at least 25 mm (1 inch) below the
top of the child restraint seat back.
3. Make necessary adjustments.
• Red harness tabs MUST be at shoulder level (page
37).
• Crotch strap should be snug against the child
(page 39).
4. Fasten the buckle. Refer to page 38.
5. Position and connect chest clip.
Chest clip MUST be at armpit level (page 38).
6. Check your work.
• Child restraint is in Position #1 (page 16).
• To properly secure this child restraint it MUST NOT
•
IMPORTANT: Once your child exceeds 18 kg (40 lb.) OR
the top of their head is within 25 mm (1 in.) of the top
of the child restraint seat back, they MUST use this child
restraint in the forward-facing position.
14
•
•
•
move more than 25 mm (1 inch) from side to side
or front to back at the rear-facing belt path (pages
19 and 23).
The child’s back and bottom are flat against the
back and bottom surfaces of the child restraint.
Red harness tabs are AT shoulder level (page 37).
Buckle tongues are fully engaged.
The level arrow is parallel with ground (page 16).
15
Rear-facing
Child Requirements for Rear-facing:
Installation Checklist
2
NEVER turn a child restraint
forward-facing with an infant
weighing less than 10 kg (22 lb.) or
less than one year of age. Crash forces
may cause serious injury or death.
Adjust the recline to
Position #1 by lifting
the back of the seat
slightly while pulling
the Recline Right
lever B.
B
3
Rear-facing
Rear-facing Installation
Using the Vehicle Seat Belt
WARNING
WARNING
If the vehicle seat belts are not routed and
fastened correctly, the child restraint may not
protect your child in a crash.
Lap and Shoulder
Belt Combination
Lap Belt Only
Infants MUST always ride facing the rear of the vehicle; the
back of the child restraint supports and protects the baby
and absorbs crash forces.
You MUST place child restraint in Full
Recline (Position #1) for rear-facing use.
C
➚
➚
A
This child restraint has three recline positions. The most
reclined position (Position #1) is ONLY for rear-facing.
Make sure that the seat is positioned so that the level
arrow is parallel with the ground.
Note: In some vehicles, it may be necessary to place a
tightly rolled towel or small blanket A beneath the front
edge of the child restraint to provide enough recline so
that the level arrow is parallel to the ground.
16
➚
C
➚
Position #1
➚
1
Remove bottom half of seat pad for easier belt
routing, as shown.
Route the vehicle seat belt through the rear-facing belt
path C, continue through the opposite opening of the
child restraint. Fasten the vehicle seat belt as shown
depending on your type of seat belt.
Note: Install locking clip on lap and shoulder belt
combinations, if necessary.
17
6
D
➚
Install Locking Clip,
if necessary.
If your vehicle was built
prior to model year
1996, and has either a lap
belt or lap/shoulder belt
that is equipped with an
emergency locking
13 mm
(0.5 inch)
retractor (ELR), you MUST
use a Locking Clip. Check
your vehicle owner’s
manual to identify which
vechicle belt system is in
your vehicle.
If your vehicle is model year 1996 or newer, it likely
has a vehicle belt system that can be locked when
tightened, and will not require use of a Locking Clip.
Locking Clip
installed properly
Consult your vehicle owner’s manual before
installing a locking clip.
WARNING
• If vehicle seat belts are not routed and fastened
correctly, the child restraint may not protect your
child in a crash.
• DO NOT use this child restraint if it moves more than
25 mm (1 in.) side to side or front to back at the rearfacing belt path. Serious injury or death may result from
poor installation. If you can not tightly secure the child
restraint, try again or move it to another location, or
install with the lower anchor connector assembly.
Check your work.
Make certain the belts are tight. If you can move the child
restraint more than 25 mm (1 inch) side to side or front
to back at the rear-facing belt path C, the vehicle belt is
not tight enough. If you have not tightly secured the child
restraint, try again, move it to another location, or install
with the lower anchor connector assembly (p. 20).
7
If your vehicle requires a Locking Clip, please call
ParentLink (see back cover) to obtain a Locking Clip and
instructions on how to install and use it.
WARNING
Remove Locking Clip from vehicle seat belt when not used
with a child restraint, or the vehicle seat belt will not properly
restrain an adult or child. Serious injury could occur.
18
WARNING
• To avoid a strangulation hazard, you MUST tightly roll or
fold excess tether strap and secure with the strap/rubber
band.
• Attach the tether hook to the storage clip when not in
use. This will keep an unused tether from hitting someone
during a crash.
E
When the tether strap is
not in use, you MUST
attach the hook E to the
back of the child restraint,
and tightly roll and secure
the strap with the strap/
rubber band.
A loose tether strap and
hook may injure your
child.
19
Rear-facing
C
C
5
➚
The seat belt must be as
tight as possible. Put your
full weight into the child
restraint as you tighten the
seat belt D.
If you can move the child
restraint more than 25 mm
(1 in.) side to side or front
to back at the rear-facing
belt path C, the vehicle belt is not tight enough, and
you need to try again, or install with the lower anchor
connector assembly (p. 20). After your vehicle seat belts
are fastened, hook the seat pad back into place.
➚
4
WARNING
SecureRight™
Quick Connector™
Adjuster
Strap
Clip
Hook
Strap
Adjuster
1
SecureRight™
Quick Connector™
B
A
C
C
Remove both lower anchor connector hooks A or clips
B from the storage clips on the base C.
2
D
D
Remove the seat pad from the seat shell (page 43).
Loosen harness straps D (page 40) and place them out
of the way, as shown.
3
➚
• ONLY use for securing child restraint to vehicle lower
anchor bars.
• ALWAYS read and follow exactly the instructions that
accompany your vehicle and child restraint.
• NEVER attach two hooks to one vehicle lower anchor
bar.
• DO NOT use the vehicle seat belts to install a child
restraint when using the lower anchor connector
assembly.
• This lower anchor connector assembly is intended to be
used ONLY as described in these instructions. Serious
injury or death may result from misuse.
• ALWAYS be sure that the lower anchor connector hook
is fully engaged onto the vehicle lower anchor bar by
pulling hard on the lower anchor connector strap. If
it is not totally engaged, the lower anchor connector
assembly will not secure your child restraint. Serious
injury or death may result.
• To avoid a strangulation hazard, you MUST store the
unused lower anchor connector assembly, with all slack
removed, in storage area on the back of the seat. Roll or
fold excess lower anchor connector strap and secure
with a rubber band to prevent serious injury to vehicle
occupants.
• In addition to these instructions, read and follow your
vehicle owner’s manual regarding installation of the child
restraint and LATCH. If there is a discrepancy,
follow your vehicle owner’s manual.
The lower anchor connector assembly that comes with
your child restraint will be one of the two types below.
Rear-facing
LATCH is a system for attaching the child restraint to your
vehicle seat. It is to be used in place of your vehicle’s seat
belts, and can be used in vehicles with LATCH anchors.
Your vehicle owner’s manual may refer to this system as
ISOFIX or Universal Anchorage System (UAS).
Know Your Lower Anchor
Connector Assembly
➚
Rear-facing Installation
Using the Lower Anchor
Connector Assembly
E
20
Remove the lower anchor connector assembly E from
the forward-facing position (back openings).
21
Correct
4
Incorrect
E
F
IMPORTANT: Make sure both lower anchor Quick Connectors
are facing upward and the straps are not twisted.
7
Using your full weight,
push the child restraint
firmly into the vehicle
seat while pulling up
on the lower anchor
connector assembly
strap to tighten.
The lower anchor connector assembly strap must be as
tight as possible.
If you can move the child restraint more than 25 mm (1
inch) side to side or front to back at the vehicle belt path
H, the lower anchor connector assembly strap is not tight
enough. You will need to try again, find another location
for your child restraint, or install with the vehicle seat belt
(page 16).
To remove the lower anchor connector assembly strap, go
to page 41.
➚
➚
➚
Crossing your arms, insert the ends of the lower anchor
connector assembly strap E in the rear-facing belt path
openings, as shown (front openings). Note: Make sure the
adjustment buckle F enters the opening on the
correct side of the child restraint, as shown.
5
F
E
After the lower anchor connector assembly strap E has
been correctly inserted, it will appear as shown above.
Note: Make sure the adjustment buckle F is on the
correct side of the child restraint, as shown.
6
8
A
G
B
WARNING
• To avoid a strangulation hazard, you MUST tightly roll or
fold excess tether strap and secure with the strap/rubber
band.
• Attach the tether hook to the storage clip when not in
use. This will keep an unused tether from hitting someone
during a crash.
G
Refer to your vehicle owner’s manual to locate the
lower anchor bars on your vehicle seat.
Attach the left hook A, or clip B, to the left anchor
bar G, and the right hook to the right anchor bar.
DOUBLE CHECK that each lower anchor connector hook
or clip is fully engaged by pulling hard on the lower
anchor connector assembly strap.
22
H
I
When the tether strap is not
in use you MUST attach the
hook I to the back of the
child restraint, and tightly
roll and secure the strap with
the strap/rubber band.
A loose tether strap and
hook may injure your child.
23
Rear-facing
➚
Using the Triumph™
Forward-facing
Child Requirements for Forward-facing:
• Weight: 10 to 29.4 kg (22 to 65 lb.)
• Height: 71 to 127 cm (28 to 50 in.) AND the tops of
the child’s ears are below the top of the child restraint
seat back.
• Age: At least one year of age.
Installation Checklist
WARNING
If your child weighs more than 29.4 kg (65 lb.) or
their shoulders are above the highest harness level,
you MUST discontinue use or the child restraint
will not protect your child.
1. Secure child restraint to the vehicle seat.
• Child restraint is in Position #2 or #3 (page 26).
• Child restraint base sits flat on vehicle seat.
• Install with vehicle seat belt (page 26) or lower
anchor connector assembly (page 32).
• Install tether strap (page 30 or 36).
• Install locking clip, if necessary (page 28).
The top of the child’s ears MUST be below the top of
the child restraint seat back.
3. Make necessary adjustments.
• Red harness tabs MUST be at shoulder level (page
37).
• Crotch strap should be snug against the child
(page 39).
4. Fasten the buckle. Refer to page 38.
5. Position and connect chest clip.
Chest clip MUST be at armpit level (page 38).
6. Check your work.
• Child restraint is in Position #2 or #3 (page 26).
IMPORTANT: Once your child exceeds 29.4 kg (65 lb.),
OR is taller than 127 cm (50 in.), they can no longer safely
use this child restraint, and you should consider
using a booster seat.
24
• Child restraint base sits flat on vehicle seat.
• To properly secure this child restraint it MUST NOT
move more than 25 mm (1 inch) from side to side
or front to back at the forward-facing belt path
(pages 29 and 35).
• The child’s back and bottom are flat against the
back and bottom surfaces of the child restraint.
• Red harness tabs are AT shoulder level (page 37).
• Buckle tongues are fully engaged.
• Tether strap is securely attached and tightened
(page 30 or 36).
25
Forward-facing
2. Set the child in the child restraint.
Forward-facing Installation
Using the Vehicle Seat Belt
1
The Intermediate Recline Position (Position #2)
and Full Upright Position (Position #3) are ONLY
for forward-facing use AND always make sure the
bottom of the child restraint sits flat on the vehicle
seat.
WARNING
If the vehicle seat belts are not routed correctly,
the child restraint may not protect your child in a crash.
4
3
B
Full Upright Position (Position #3)
Intermediate Recline Position (Position #2)
Route the vehicle seat belt
through the child restraint.
Use the BeltTrac access
flap B for easier seat belt
routing.
5
Buckle the vehicle seat belt.
Lap and Shoulder
Belt Combination
Lap Belt Only
The child must weigh
10 to 22.7 kg
(22 - 50 lb.).
2
Fasten the vehicle seat belt as shown depending on your
type of seat belt.
Note: Install locking clip on lap and shoulder belt
combinations, if necessary.
A
Adjust the recline to Positions #2 or #3 by lifting the
back of the seat slightly while pulling the ReclineRight
lever A.
26
WARNING
DO NOT allow the vehicle seat belt release button to touch
the child restraint. Accidental contact may cause the seat
belt to release. If necessary, turn the vehicle seat belt button
away from the child restraint or move the child restraint to
a different location.
27
Forward-facing
The child must weigh
10 to 29.4 kg
(22 - 65 lb.).
The vehicle seat belt
must be as tight as
possible.
Using your full weight,
push the child restraint
firmly into the vehicle
seat as you tighten the
vehicle belt C.
➚
D
If you can move the child restraint more than 25 mm
(1 in.) side to side or front to back at the forward-facing
belt path D, the seat belt is not tight enough, you
will need to try again, or install with the lower anchor
connector assembly (page 32).
8
➚
Consult your vehicle owner’s manual before
installing a locking clip.
If your vehicle requires a Locking Clip, please call
ParentLink (see back cover) to obtain a Locking Clip and
instructions on how to install and use it.
Remove Locking Clip from vehicle seat belt when not used
with a child restraint, or the vehicle seat belt will not properly
restrain an adult or child. Serious injury could occur.
D
➚
WARNING
➚
WARNING
• If vehicle seat belts are not routed and fastened
correctly, the child restraint may not protect your
child in a crash.
• DO NOT use this child restraint if it moves more than
25 mm (1 in.) side to side or front to back at the vehicle
belt path D. Serious injury or death may result from
poor installation. If you can not tightly secure the child
restraint, try again or move it to another location, or
install with the lower anchor connector assembly
(page 32).
28
29
Forward-facing
If your vehicle was built
prior to model year
1996, and has either a lap
belt or lap/shoulder belt
that is equipped with an
emergency locking
13 mm
(0.5 inch)
retractor (ELR), you MUST
use a Locking Clip. Check
your vehicle owner’s
manual to identify which
vechicle belt system is in
your vehicle.
If your vehicle is model year 1996 or newer, it likely
has a vehicle belt system that can be locked when
tightened, and will not require use of a Locking Clip.
Locking Clip
installed properly
7
C
➚
Install Locking Clip,
if necessary.
6
This page is intentionally blank.
9
E
F
G
Connect the tether
hook E to the vehicle
tether anchor F behind
the vehicle seat, as
shown. (Please consult
your vehicle owner’s
manual, as tether anchor
locations may vary.) Pull
the strap G and tighten
the tether securely.
Forward-facing
Note: If your tether strap does not reach the vehicle
tether anchor bracket, call Evenflo’s ParentLink for a
tether extender.
WARNING
• To avoid a strangulation hazard, you MUST tightly
roll or fold excess tether strap and secure with the
strap/rubber band.
• Attach the tether hook to the storage clip when not
in use. This will keep an unused tether from hitting
someone during a crash.
After adjusting the top tether strap, you may have
excess strap; DO NOT cut it off. If you do, it may not be
long enough to use in another vehicle. Instead, tightly
roll up the excess tether strap and place the rubber
band around the bundle.
Note: Refer to your vehicle owner’s manual for the
location of the tether anchor bracket in your vehicle.
Older vehicles may not come equipped with anchor
bracket hardware. Check with your vehicle dealer.
If you have questions regarding tether anchors which are
not addressed by the vehicle owner’s manual,
or answered by an authorized dealer/vehicle
manufacturer call Evenflo’s ParentLink.
30
31
Forward-facing Installation
Using the Lower Anchor
Connector Assembly
LATCH is a system for attaching the child restraint to your
vehicle seat. It is to be used in place of your vehicle’s seat
belts, and can be used in vehicles with LATCH anchors. Your
vehicle owner’s manual may refer to this system as ISOFIX
or Universal Anchorage System (UAS).
WARNING
• In addition to these instructions, read and follow your
vehicle owner’s manual regarding installation of the child
restraint and LATCH. If there is a discrepancy,
follow your vehicle owner’s manual.
Know Your Lower Anchor
Connector Assembly
The lower anchor connector assembly that comes with your
child restraint will be one of the two types below.
SecureRight™
Quick Connector™
Adjuster
DO NOT Install by this
method for a child weighing
more than 22.7 kg (50 lb.).
Strap
Clip
Hook
Strap
SecureRight™
1
32
B
A
WARNING
• ONLY use for securing child restraint to vehicle lower
anchor bars.
• ALWAYS read and follow exactly the instructions that
accompany your vehicle and child restraint.
• NEVER attach two lower anchor connector hooks to one
vehicle lower anchor bar.
• DO NOT use the vehicle seat belts to install a child restraint when using the lower anchor connector assembly.
• This lower anchor connector assembly is intended to be
used ONLY as described in these instructions. Serious injury
or death may result from misuse.
• ALWAYS be sure that the lower anchor connector hook
is fully engaged onto the vehicle lower anchor bar by pulling hard on the lower anchor connector strap. If it
is not totally engaged, the lower anchor connector
assembly will not secure your child restraint. Serious injury
or death may result.
• To avoid a strangulation hazard, you MUST store the
unused lower anchor connector assembly, with all slack
removed, in storage area on the back of the seat. Roll or
fold excess lower anchor connector strap and secure with a
rubber band to prevent serious injury to vehicle occupants.
Quick Connector™
C
C
Remove two lower anchor connector hooks A, or clips
B, from the the base C.
2
Lower Anchor Connector
Strap in Forward-facing
Position
Lower Anchor Connector Strap
in Rear-facing Position
D
D
E
E
Remove the seat pad from the seat shell (page 43).
Loosen harness straps D (page 40) and place them out of
the way, as shown.
• If your lower anchor connector strap E is already
in the forward- facing position (back openings),
proceed to step 6.
• If your lower anchor connector strap E is in the rearfacing position (front openings), continue to step 3.
33
Forward-facing
Adjuster
6
3
E
➚
Remove the lower anchor connector strap E from the
rear-facing position (front openings).
4
E
B
G
G
Refer to your vehicle owner’s manual to locate the
lower anchor bars on your vehicle seat.
Attach the left hook A, or clip B, to the left anchor
bar G, and the right hook to the right anchor bar.
DOUBLE CHECK that each lower anchor connector
hook or clip is fully engaged by pulling hard on the lower
anchor connector strap.
F
➚
➚
Correct
Crossing your arms, insert the ends of the lower anchor
connector strap E in the forward-facing belt path
openings, as shown (back openings). Note: Make sure
the adjustment buckle F enters the opening on the
correct side of the child restraint, as shown.
5
Incorrect
IMPORTANT: Make sure both lower anchor Quick Connectors
are facing upward and the straps are not twisted.
7
E
F
After the lower anchor connector strap E has been
correctly inserted, it will appear as shown above.
Note: Make sure the adjustment buckle F is on the
correct side of the child restraint, as shown.
34
➚
➚
Using your full weight push
the child restraint firmly into
the vehicle seat, while pulling
up on the lower anchor
connector strap
to tighten.
The lower anchor connector
strap must be as tight as
possible. If you can move
the child restraint more than
25 mm (1 in.) side to side
or front to back at the belt
path H, the lower anchor
connector strap is not tight
enough. You will need to try
again, find another location for your child restraint, or
install with the vehicle seat belt (page 26). To remove the
lower anchor connector strap, go to page 41.
H
35
Forward-facing
➚
A
8
Securing Your Child
in the Child Restraint
WARNING
• Failure to follow these instructions could result in serious
injury to your child or other vehicle occupants.
• The tether strap is for forward-facing use only.
1
I
J
K
Connect the tether hook I
to the vehicle tether anchor
J behind the vehicle seat, as
shown. (Please consult your vehicle owner’s manual, as
tether anchor locations may vary.) Pull the strap K and
tighten the tether securely.
Note: If your tether strap does not reach the vehicle
tether anchor bracket, call Evenflo’s ParentLink for a tether
extender.
Place baby in the child restraint. The baby’s back and
bottom should be flat against the restraint. If there is a gap,
the baby will not be comfortable.
2
A
WARNING
• To avoid a strangulation hazard, you MUST tightly
roll or fold excess tether strap and secure with the
strap/rubber band.
• Attach the tether hook to the storage clip when not
in use. This will keep an unused tether from hitting
someone during a crash.
After adjusting the top tether strap, you may have
excess strap; DO NOT cut it off. If you do, it may not be
long enough to use in another vehicle.
Instead, tightly roll up the excess tether strap and
place the rubber band around the bundle.
Note: Refer to your vehicle owner’s manual for the
location of the tether anchor bracket in your vehicle.
Older vehicles may not come equipped with anchor
bracket hardware. Check with your vehicle dealer.
If you have questions regarding tether anchors which
are not addressed by the vehicle owner’s manual, or
answered by an authorized dealer/vehicle manufacturer
call Evenflo’s ParentLink.
36
A
Bring each harness strap over the child’s shoulders. Slide
the buckle tongues A down towards the buckle to snug
the harness.
3
➚
B
Grasp both red
harness tabs B and
slide downward until
the harness straps are at
the child’s shoulders.
➚
B
37
4
7
The harness straps must be
snug against the child.
A snug strap should not allow
any slack. It lies in a relatively
straight line without sagging.
It does not press on the child’s
flesh or push the child’s body
into an unnatural position.
Check the harness straps near
the shoulders for slack. You
should NOT be able to pinch
the harness (see illustration).
Adjust as needed.
C A
Insert both buckle tongues A into the buckle C. Pull up
on the harness strap to check that the buckle tongues
are fastened.
5
Adjusting the Crotch Strap
As your child grows, you will need to change the crotch
strap position so that it is in the slot closest to your child.
The crotch strap should ALWAYS be as close as possible to,
but NEVER under, the child’s bottom.
Front Position
Rear Position
D
Tighten the harness straps by turning either one of
TensionRight knobs D.
To loosen the harness straps, refer to page 40.
6
A
E
A
B
A
A
B
G
G
Fasten the chest clip E by snapping the two halves
together, as shown. Slide chest clip to armpit level.
38
G
B
To adjust the crotch strap, grasp the bottom of the strap
G it to align with the length wise slot B. Move
A and twist
to the desired position. Twist the strap back into position.
Be sure that the crotch strap is securely in place.
39
Removing Child from the Restraint
1
A
Removing the Lower
Anchor Connector Assembly
1
A
To unfasten the chest clip, push the release button A and
pull apart.
2
B
Press the adjuster release
button A to loosen harness
strap.
Press the red buckle release B, and remove the buckle
tongues.
2
3
➚
D
4
E
C
Loosen the harness strap
by pressing the tension
release button C located
on the front of the seat.
While pressing the
button C, pull up on
the harness straps D near
the child’s lap.
To easily remove your
child, unbuckle the crotch
buckle and insert the
buckle tongues into the
buckle tongue holders
E on each side of the
restraint.
Not available on all models.
E
B
D
E
C
F
D
To remove the hook B,
press the tab C and
twist, then remove from
anchor D.
To remove the clip E,
pull the red release
strap F and remove clip
from anchor D.
SecureRight™
Quick Connector™
A
B
3
G
G
When the lower anchor connector system is not in use,
you MUST attach each hook A, or clip B, onto the base
G. Be sure the lower anchor connector straps are tucked
completely inside the seat shell. A loose lower anchor
connector strap and hook may injure your child.
40
41
Removing the Tether Strap
1
The tether strap that comes with your child
restraint will be one of the two types below.
A
Removing the Seat Pad
1
You will need to remove your seat pad for cleaning.
B
Unbuckle harness straps
and disconnect chest clip.
Press the adjuster release
button B to loosen
tether strap.
2
C
B
Press the tab B
and twist, then
remove the hook
from the anchor C.
2 ➚
➚
Tilt the adjuster A and
slide the tether strap to
loosen.
3
➚
➚
WARNING
When the tether
strap is not in use you
MUST attach the hook
D to the back of the
child restraint, and
tightly roll and secure
the strap with the
strap/rubber band.
A loose tether strap
and hook may injure
your child.
D
Starting at the bottom
of the seat, unfasten
all seat pad hooks A.
➚
➚
• To avoid a strangulation hazard, you MUST tightly roll
or fold excess tether strap and secure with the strap/
rubber band.
• Attach the tether hook to the storage clip when not
in use. This will keep an unused tether from hitting
someone during a crash.
A
B
3
C
Carefully remove the seat pad B from around each
cup holder C.*
*Cup holders not available for all models. Styles may vary.
42
43
3
B
A
Open the BeltTrac
access flap and
remove the seat pad
B from the seat
shell.
➚
➚
2
A
➚
Place seat pad A in seat
shell.
4 ➚
➚
A
C
➚
1
C
➚
Installing the Seat Pad
C
Stretch seat pad A over cup
holders* C. Make sure the
edges of the seat pad are
tucked beneath the edge of
each cup holder to enclose
the foam underneath.
➚
4
Starting at the top of the
seat and working your
way downward, fasten
all seat pad hooks A.
*Optional cup holders not available for all models.
Styles may vary.
B
Push BeltTrac access flap B
behind harness straps and
bring buckle assembly
through the seat pad, as
shown.
44
45
Installing the Accessories
The Optional Cup Holder
The Body Pillow and Infant Head
Support
WARNING
Use the Body Pillow and Infant Head Support with the
child restraint in the rear-facing position ONLY.
D
B
A
The optional Body Pillow C
is used to help support your
child by placing it in the
restraint, as shown.
C
A
WARNING
• Use the fold-down cup holder with the child restraint in
the forward-facing position ONLY.
• DO NOT use the accessories to store cans or hard cups.
Only for use with soft cups (such as styrofoam or paper).
• DO NOT place any cups that contain hot liquids in the
accessories.
• DO NOT attach any other items to this child restraint
unless it has been certified for use with this specific child
restraint.
The optional Infant Head Support D should lie flat
against the seat back, as shown. Be sure to cut off the
plastic attachment between the head support and the
seat pad. Small parts may be a choking hazard.
Note: Support the child’s head. For about the first three
months, a baby’s head needs extra support. Use a small
rolled towel on each side of the baby’s head or the
optional Head Support.
To install the fold-down cup holder* A, move seat
pad B out of the way and install the cup holder
onto the side of the restraint.
*Cup holder style may differ from illustration.
46
47
Removing the Adjustable Headrest
1
Not available on all models.
A
DO NOT use if the top of the
child’s ears are above the top
of the headrest at its highest
position.
Remove the headrest for this
child to use the restraint,
as long as the child meets
all other height and weight
requirements.
Unbuckle harness straps,
disconnect chest clip, and
raise BeltTrac access flap A.
2
A
Fold in both sides of the
BeltTrac access flap A.
➚
3
B
Remove the headrest B
from the folded BeltTrac
access flap A.
A
48
4
Lower BeltTrac access
flap A and attach Velcro®.
A
IMPORTANT: Support the child’s head. For about the first
three months, a baby’s head needs extra support. Use a
small rolled towel on each side of the baby’s head with the
adjustable headrest, if necessary.
Care and Cleaning
• To help protect the vehicle upholstery, place a towel
beneath and behind the child restraint.
• Plastic and metal parts may be wiped clean with mild soap
and water and dried with a soft cloth. Do not use abrasive
cleaners or solvents.
• Take care not to damage any labels.
• The harness can be wiped clean with mild soap and water.
Allow harness to air dry. DO NOT lubricate or immerse in
water the Quick Connector, buckle, or any other part of this
child restraint, unless rinsing is permitted, as stated on the
back of the buckle for your restraint.
• Machine wash the seat pad separately in cold water, delicate cycle, and tumble dry 10 – 15 minutes on low heat.
• NEVER use child restraint without the seat pad.
• Leather pads (not available on all models) may be cleaned.
For best results spot clean with mild soap and water or with
a mixture of 10 parts water to 1 part mild alcohol. Allow to
air dry. DO NOT MACHINE WASH.
49
Securing Your Child
Restraint in Aircraft
The Federal Aviation Administration (FAA) recommends that
you secure your child for air travel in an appropriate child
restraint based on your child’s weight and size. Turbulence
can happen with little or no warning. When turbulence
occurs, the safest place for your child is in a properly
installed child restraint, not in an adult’s lap or on the
aircraft seat with its seat belt. Keeping your child
in a child restraint during the flight will help ensure your
family arrives safely at your destination.
The FAA recommends that a child weighing:*
• more than 18 kg (40 lbs) use an aircraft seat belt;
• less than 9 kg (20 lbs) use a rear-facing child restraint;
and
• from 9 to 18 kg (20 to 40 lbs) use a forward-facing child
restraint.
* Please note that these FAA recommendations may
vary from those applicable to the use of your child
restraint in a motor vehicle.
IMPORTANT: You must use the internal harness when
installing the child restraint in aircraft.
Installing Child Restraint
Rear-facing in Aircraft
1
2
D
E
A
Pull the seat pad off the front of the child restraint.Route
the aircraft seat belt A through the rear-facing belt path
D opening on one side and continue through the belt
path opening on the opposite side of the child restraint,
as shown above.
IMPORTANT: Make sure the aircraft seat belt A is in
front of the crotch strap E, as shown above.
3
Fasten the aircraft
seat belt A.
IMPORTANT: Before installing the child restraint,
make sure the aircraft seat is in a fully
upright position.
C
B
Unbuckle the aircraft seat
belts A and lay over the
armrests, as shown.
Adjust the child
restraint B to its recline
position (page 17), then
place it on the aircraft
seat C rear-facing.
A
A
50
51
Installing Child Restraint
Forward-facing in Aircraft
4
1
F
IMPORTANT: Before installing the child restraint,
make sure the aircraft seat is in a fully
upright position.
D
B
A
C
Unbuckle the aircraft seat
belts A and lay over the
armrests, as shown.
Adjust the child restraint B
to its upright position
(page 26), then place it
on the aircraft seat C
forward-facing.
A
The aircraft seat belt A must be as tight as possible. Route
the excess seat belt strap F back through the rear-facing
belt path D opening, as shown above. Using your full
weight, push the child restraint firmly onto the aircraft
seat while pulling on the excess seat belt strap to tighten.
Check your work. Reconnect the seat pad to the front
of the child restraint. Try to move the child restraint in
all directions. If you can move the restraint more than 25
mm (1 inch) side to side or front to back at the rear-facing
belt path D, the aircraft seat belt A is not tight enough,
and you MUST install again until the seat belt is tight.
2
D
A
Route the aircraft seat belt A through the forward-facing
belt path D opening in the back of the child restraint
and continue through the belt path opening on the
opposite side of the child restraint.
Note: Lift the restraint’s seat pad away for easier access.
52
53
Replacement Parts
3
Fasten the aircraft seat
belt A.
A
Not available on all models. Styles may vary.
To order replacement parts you can order on-line at www.
evenflo.com or contact Evenflo. When you contact us, please
have the product model number and date of manufacture (found
on the back of the child restraint).
Clip:
1 NotLocking
included with
child restraint, see
page 18 or 28
4
The aircraft seat belt must
be as tight as possible.
Route the excess aircraft
seat belt strap E back
through the forwardfacing belt path D
opening, as shown above.
Using your full weight,
push the child restraint
firmly onto the aircraft
seat while pulling on the
excess seat belt strap to
tighten.
D
E
Anchor
5Lower
Connector Assembly
9 Seat Foam-Top
2 Headrest
3 Body Pillow
Anchor
6 Lower
Connector Assembly
with Quick
Connectors™
7 Seat Foam-Rgt
bk Seat Pad
4 Tether Extender
Note: Because of the fixed length of aircraft seat belts, the belt
buckle could be behind the child’s back after tightening the
belt. For your child’s comfort, Evenflo recommends cushioning
the child’s back by placing a small pillow or folded-up blanket,
or a folded-up jacket, over the belt buckle.
Check your work. Reconnect the seat pad to the front
of the child restraint. Try to move the child restraint in all
directions. If you can move the restraint more than 25 mm
(1 inch) side to side or front to back at the forward-facing
belt path, the aircraft seat belt is not tight enough, and
you MUST install again until the seat belt is tight.
54
8 Seat Foam-Lft
bl Cup Holder options
Proper Disposal of this Child Restraint
At the end of this child restraint’s useful life, Evenflo
encourages you to dispose of it properly. Most of the
components in this child restraint are recyclable.
1. Remove all fabric and padding.
2. Remove all screws and disassemble the restraint.
3. Recycle all plastic/foam parts and discard the rest.
If your local recycling center won’t accept the padding,
you may dispose of it in the landfill.
Note: Evenflo uses recycled materials in the manufacturing
process whenever possible but never for components that are
critical for safety.
55
Limited Warranty
For a period of 90 days from the original purchase of
this Product, Evenflo warrants to the original end user
(“Purchaser”) this Product (including any accessories)
against defects in material or workmanship. Evenflo’s sole
obligation under this express limited warranty shall be, at
Evenflo’s option, to repair or replace any Product that is
determined to be defective by Evenflo and determined to
be covered by this warranty.
Repair or replacement as provided under this
warranty is the exclusive remedy of the Purchaser. Proof
of purchase in the form of a receipted invoice or bill of
sale evidencing that the Product is within the warranty
period must be presented to obtain warranty service. This
express limited warranty is extended by Evenflo ONLY to
the original Purchaser of the Product and is not assignable
or transferable to subsequent purchasers or end users
of the Product. For warranty service, contact Evenflo’s
ParentLink Consumer Resource Center at www.evenflo.
com.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE
LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT
IS HEREBY DISCLAIMED. EVENFLO SHALL NOT BE LIABLE
FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL OR
PUNITIVE DAMAGES OF ANY KIND FOR BREACH OF
THE EXPRESS LIMITED WARRANTY ON THIS PRODUCT,
OR ANY WARRANTY IMPLIED BY OPERATION OF LAW.
OTHER THAN THE EXPRESS LIMITED WARRANTY SET
FORTH ABOVE, THERE ARE NO OTHER WARRANTIES THAT
ACCOMPANY THIS PRODUCT AND ANY ORAL, WRITTEN
OR ANY OTHER EXPRESS REPRESENTATION OF ANY KIND
IS HEREBY DISCLAIMED.
USA: 1-800-233-5921, 8 AM to 5 PM E.T.
Canada: 1-937-773-3971
México: 01-800-706-12-00
56
USA: 1-800-233-5921, 8 AM to 5 PM E.T.
Canada: 1-937-773-3971
México: 01-800-706-12-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising