- No category
advertisement
DIMP-15376-New HEATBOOK-aw 2/10/06 10:18 am Page 50
radiant panel bathroom heaters
the Apollo range
The unique Apollo range of radiant panel bathroom heaters provides the ultimate in bathroom heating.
Combining the benefits of high comfort radiant panel heating with the added convenience of fixed rails for drying and airing towels, Apollo is the ideal solution where towel drying and full room heating are required from a single appliance.
Incorporating highly accurate electronic thermostatic control, Apollo can be used stand alone or as part of an integrated whole-house system controlled by Dimplex pilot wire or mains borne signalling multi-heater programmers.
Range features
• Compact, stylish casing with distinctive curved grille.
• Two fixed towel hangers (not heated).
• Highly comfortable radiant heat output, reducing heat stratification and energy wastage.
• Fitted with an electronic thermostat, accurate to within 0.1ºC to maintain a stable room temperature.
• User selectable comfort, background and frost protection settings.
• Splash proof (IPX4 rated) for use in bathrooms and wet areas.
• Controls cover which can be locked if necessary.
• Compatible with Dimplex single or 4 zone multi-heater programmers.
50 kitchens and bathrooms
Model APL100
DIMP-15376-New HEATBOOK-aw 2/10/06 11:05 am Page 51
technical specifications
Electronic Control
Dimplex electronic panel heaters feature highly accurate electronic thermostats, providing superior comfort and operating efficiency. As the room temperature nears the desired set point, power to the elements is reduced, and the room temperature closely monitored to an accuracy of less than 0.3ºC, minimising overshoot and temperature drift, resulting in better energy-efficiency and user comfort.
Being electronic, control is totally silent and reliable
– performance will not deteriorate even over many year’s use.
Desired temp
Typical overshoot and poor regulation now improved upon by Apollo
Apollo Error band
+/- 0.1
0 C max
Main and Fixing Dimensions
96
100
248
440
96
100
Wall fixing points
Y
100 min
200
115
Initial room temp
Electronic thermostat
Electro-mechanical thermostat
Controls
1 Function control
User selection of “comfort”, “background”
(4ºC below the thermostat setting) and “frost protection” (5ºC), off and programmed operation (if programmer is fitted). Neon indicator shows function selected.
2 Thermostat Dial
The dial is marked * to 9. The * setting represents a room temperature of approximately 5ºC and may be used for protection against frost. The other settings range up to a maximum room temperature of approximately 35ºC. A neon indicator shows when the element is operating.
3 Plug-in control modules
A range of optional plug in control modules are available for use with Calidou:
– Single zone pilot wire programmer (RX9911) controls up to 20 slave heaters linked via pilot wire. Provides 7 day control, switching heater between comfort and setback mode. Can be removed from heater for easy programming.
– Single zone mains borne signalling programmer (RX9912) controls multiple slave heaters, with RX9913 MBS receivers fitted to each slave. Provides 7 day control, switching heater between comfort and setback modes.
See page 24-26 for full details on the range of plug in control modules.
163 mm 150 min
Model No.
APL100
APL150
Loading
1.0kW
1.5kW
Height
830mm
1040mm
Multi Zone Control
Compatible with Dimplex 4-zone pilot wire and mains borne signalling controllers (RX9913 receivers for MBS systems).
Elements
Two mineral filled sheathed electric elements are embedded in aluminium heating plates. Low element operating temperature of around 200ºC reduces air drying effects and dust burning.
The heating plates have a unique design – the forward face is finished in matt black and has greater surface area to maximise radiant heat.
The reverse side is in its natural smooth aluminium state to minimise heat loss to the wall.
The design provides an even temperature across the front panel, using the whole surface area available and maximises the throw of radiant heat into the room.
Width
440mm
440mm
Y
468mm
618mm
Weight
7.2kg
9.3kg
IP Rating
Splash-proof IPX4 for use in wet areas.
Construction
Durable polyester powder coated steel with mesh steel front grille.
Installation
A detachable wall-mounting frame allows quick wall fixing.
Electrical Connections
2m 4-core cable (live, neutral, earth and pilot wire) supplied fitted to each heater.
Colour/Finish
White.
1 2
technical specification 51
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement