************************************************************************** USACE / NAVFAC / AFCEC / NASA ...

************************************************************************** USACE / NAVFAC / AFCEC / NASA    ...
**************************************************************************
USACE / NAVFAC / AFCEC / NASA
UFGS-08 41 13 (February 2011)
Change 1 - 11/12
----------------------------Preparing Activity: NASA
Superseding
UFGS-08 41 13 (August 2010)
UNIFIED FACILITIES GUIDE SPECIFICATIONS
References are in Agreement with UMRL dated January 2016
**************************************************************************
SECTION TABLE OF CONTENTS
DIVISION 08 - OPENINGS
SECTION 08 41 13
ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS
02/11
PART 1
GENERAL
1.1
REFERENCES
1.2
ADMINISTRATIVE REQUIREMENTS
1.2.1
Pre-Installation Meetings
1.3
SUBMITTALS
1.4
QUALITY ASSURANCE
1.4.1
Qualifications
1.4.1.1
Installer Qualifications
1.4.1.2
Manufacturer Qualifications
1.4.2
Single Source Responsibility
1.5
DELIVERY, STORAGE, AND HANDLING
1.5.1
Ordering
1.5.2
Packing, Shipping, Handling and Unloading
1.5.3
Storage and Protection
1.6
PROJECT / SITE CONDITIONS
1.6.1
Field Measurements
PART 2
PRODUCTS
2.1
SYSTEM DESCRIPTION
2.1.1
Design Requirements for Aluminum (Entrances and Components)
2.1.1.1
Material Standard
2.1.1.2
Tolerances
2.1.2
Performance Requirements
2.1.2.1
Air Infiltration
2.1.2.2
Wind Loads
2.1.2.3
Deflection
2.1.2.4
Condensation Resistance and Thermal Transmittance
2.1.2.5
Water Infiltration
2.2
FABRICATION
2.2.1
Entrance System Fabrication
2.2.2
Shop Assembly
2.2.2.1
Welding
2.2.3
Fabrication Tolerance
SECTION 08 41 13
Page 1
2.2.3.1
Material Cuts
2.2.3.2
Maximum Offset At Consecutive Members
2.2.3.3
Maximum Offset At Glazing Pocket Corners
2.2.3.4
Joints
2.2.3.5
Variation
2.2.3.6
Flatness
2.3
ACCESSORIES
2.3.1
Fasteners
2.3.2
Perimeter Anchors
2.3.3
Standard Entrance Hardware
2.3.3.1
Weatherstripping
2.3.3.2
Threshold
2.3.3.3
Offset Pivots
2.3.3.4
Panic Device
2.3.3.5
Closer
2.3.3.6
Security Lock/Dead Lock
2.3.3.7
Cylinder(s)/Thumb-turn
2.3.3.8
Cylinder Guard
2.4
RELATED MATERIALS
2.4.1
Sealants
2.4.2
Glass
PART 3
EXECUTION
3.1
EXAMINATION
3.1.1
Site Verification of Conditions
3.2
INSTALLATION
3.2.1
Preparation
3.2.1.1
Adjacent Surfaces Protection
3.2.1.2
Aluminum Surface Protection
3.2.2
Adjusting
3.2.3
Related Products Installation Requirements
3.2.3.1
Sealants (Perimeter)
3.2.3.2
Glass
3.2.3.3
Reference
3.3
PROTECTION AND CLEANING
3.3.1
Protection
3.3.2
Cleaning
3.4
WARRANTY
-- End of Section Table of Contents --
SECTION 08 41 13
Page 2
**************************************************************************
USACE / NAVFAC / AFCEC / NASA
UFGS-08 41 13 (February 2011)
Change 1 - 11/12
----------------------------Preparing Activity: NASA
Superseding
UFGS-08 41 13 (August 2010)
UNIFIED FACILITIES GUIDE SPECIFICATIONS
References are in Agreement with UMRL dated January 2016
**************************************************************************
SECTION 08 41 13
ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS
02/11
**************************************************************************
NOTE: This guide specification covers the
requirements for Aluminum Entrances, glass and
glazing, door hardware and components.
Adhere to UFC 1-300-02 Unified Facilities Guide
Specifications (UFGS) Format Standard when editing
this guide specification or preparing new project
specification sections. Edit this guide
specification for project specific requirements by
adding, deleting, or revising text. For bracketed
items, choose applicable items(s) or insert
appropriate information.
Remove information and requirements not required in
respective project, whether or not brackets are
present.
Comments, suggestions and recommended changes for
this guide specification are welcome and should be
submitted as a Criteria Change Request (CCR).
**************************************************************************
PART 1
1.1
GENERAL
REFERENCES
**************************************************************************
NOTE: This paragraph is used to list the
publications cited in the text of the guide
specification. The publications are referred to in
the text by basic designation only and listed in
this paragraph by organization, designation, date,
and title.
Use the Reference Wizard's Check Reference feature
when you add a RID outside of the Section's
Reference Article to automatically place the
reference in the Reference Article. Also use the
Reference Wizard's Check Reference feature to update
the issue dates.
SECTION 08 41 13
Page 3
References not used in the text will automatically
be deleted from this section of the project
specification when you choose to reconcile
references in the publish print process.
**************************************************************************
The publications listed below form a part of this specification to the
extent referenced. The publications are referred to within the text by the
basic designation only.
AMERICAN ARCHITECTURAL MANUFACTURERS ASSOCIATION (AAMA)
AAMA 1503
(2009) Voluntary Test Method for Thermal
Transmittance and Condensation Resistance
of Windows, Doors and Glazed Wall Sections
AAMA 501
(2005) Methods of Test for Exterior Walls
AAMA 503
(2008) Voluntary Specification for Field
Testing of Newly Installed Storefronts,
Curtain Walls and Sloped Glazing Systems
AAMA 800
(2010) Voluntary Specifications and Test
Methods for Sealants
AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI)
ANSI Z97.1
(2009; Errata 2010) Safety Glazing
Materials Used in Buildings - Safety
Performance Specifications and Methods of
Test
AMERICAN SOCIETY OF CIVIL ENGINEERS (ASCE)
ASCE 7
(2010; Errata 2011; Supp 1 2013) Minimum
Design Loads for Buildings and Other
Structures
ASTM INTERNATIONAL (ASTM)
ASTM B221
(2014) Standard Specification for Aluminum
and Aluminum-Alloy Extruded Bars, Rods,
Wire, Profiles, and Tubes
ASTM B221M
(2013) Standard Specification for Aluminum
and Aluminum-Alloy Extruded Bars, Rods,
Wire, Profiles, and Tubes (Metric)
ASTM E1105
(2000; R 2008) Standard Test Method for
Field Determination of Water Penetration
of Installed Exterior Windows, Skylights,
Doors, and Curtain Walls, by Uniform or
Cyclic Static Air Pressure Difference
ASTM E1424
(1991; R 2008) Standard Test Method for
Determining the Rate of Air Leakage
Through Exterior Windows, Curtain Walls,
and Doors Under Specified Pressure and
SECTION 08 41 13
Page 4
Temperature Differences Across the Specimen
ASTM E1886
(2013a) Standard Test Method for
Performance of Exterior Windows, Curtain
Walls, Doors, and Impact Protective
Systems Impacted by Missile(s) and Exposed
to Cyclic Pressure Differentials
ASTM E283
(2004; R 2012) Determining the Rate of Air
Leakage Through Exterior Windows, Curtain
Walls, and Doors Under Specified Pressure
Differences Across the Specimen
ASTM E330
(2002; R 2010) Structural Performance of
Exterior Windows, Doors, Skylights and
Curtain Walls by Uniform Static Air
Pressure Difference
ASTM E331
(2000; R 2009) Water Penetration of
Exterior Windows, Skylights, Doors, and
Curtain Walls by Uniform Static Air
Pressure Difference
ASTM E783
(2002; R 2010) Standard Test Method for
Field Measurement of Air Leakage Through
Installed Exterior Windows and Doors
ASTM F1642
(2012) Standard Test Method for Glazing
and Glazing Systems Subject to Airblast
Loadings
BUILDERS HARDWARE MANUFACTURERS ASSOCIATION (BHMA)
ANSI/BHMA A156.10
(2011) Power Operated Pedestrian Doors
ANSI/BHMA A156.4
(2013) Door Controls - Closers
GLASS ASSOCIATION OF NORTH AMERICA (GANA)
GANA Glazing Manual
(2004) Glazing Manual
U.S. NATIONAL ARCHIVES AND RECORDS ADMINISTRATION (NARA)
16 CFR 1201
Safety Standard for Architectural Glazing
Materials
UNDERWRITERS LABORATORIES (UL)
UL 325
1.2
1.2.1
(2013; Reprint May 2015) Door, Drapery,
Gate, Louver, and Window Operators and
Systems
ADMINISTRATIVE REQUIREMENTS
Pre-Installation Meetings
Conduct pre-installation meeting to verify project requirements, substrate
conditions, manufacturer's installation instructions, and manufacturer's
warranty requirements.
SECTION 08 41 13
Page 5
following the "G" typically are not used for Navy,
Air Force, and NASA projects.
An "S" following a submittal item indicates that the
submittal is required for the Sustainability
Notebook to fulfill federally mandated sustainable
requirements in accordance with Section 01 33 29
SUSTAINABILITY REPORTING.
Choose the first bracketed item for Navy, Air Force
and NASA projects, or choose the second bracketed
item for Army projects.
**************************************************************************
Government approval is required for submittals with a "G" designation;
submittals not having a "G" designation are [for Contractor Quality Control
approval.][for information only. When used, a designation following the
"G" designation identifies the office that will review the submittal for
the Government.] Submittals with an "S" are for inclusion in the
Sustainability Notebook, in conformance to Section 01 33 29 SUSTAINABILITY
REPORTING. Submit the following in accordance with Section 01 33 00
SUBMITTAL PROCEDURES:
SD-01 Preconstruction Submittals
Sample Warranty[; G[, [____]]]
Listing of Product Installations[; G[, [____]]]
SD-02 Shop Drawings
Installation Drawings[; G[, [____]]]
[
]
Fabrication Drawings[; G[, [____]]]
SD-03 Product Data
Manufacturer's Catalog Data[; G[, [____]]]
SD-04 Samples
Finish and Color Samples[; G[, [____]]]
SD-06 Test Reports
Certified Test Reports[; G[, [____]]]
SD-07 Certificates
Manufacturer's Product Warranty[; G[, [____]]]
1.4
QUALITY ASSURANCE
1.4.1
1.4.1.1
Qualifications
Installer Qualifications
Provide documentation of Installer experience [as determined by Contractor]
to perform work of this section, who has specialized in the installation of
SECTION 08 41 13
Page 7
following the "G" typically are not used for Navy,
Air Force, and NASA projects.
An "S" following a submittal item indicates that the
submittal is required for the Sustainability
Notebook to fulfill federally mandated sustainable
requirements in accordance with Section 01 33 29
SUSTAINABILITY REPORTING.
Choose the first bracketed item for Navy, Air Force
and NASA projects, or choose the second bracketed
item for Army projects.
**************************************************************************
Government approval is required for submittals with a "G" designation;
submittals not having a "G" designation are [for Contractor Quality Control
approval.][for information only. When used, a designation following the
"G" designation identifies the office that will review the submittal for
the Government.] Submittals with an "S" are for inclusion in the
Sustainability Notebook, in conformance to Section 01 33 29 SUSTAINABILITY
REPORTING. Submit the following in accordance with Section 01 33 00
SUBMITTAL PROCEDURES:
SD-01 Preconstruction Submittals
Sample Warranty[; G[, [____]]]
Listing of Product Installations[; G[, [____]]]
SD-02 Shop Drawings
Installation Drawings[; G[, [____]]]
[
]
Fabrication Drawings[; G[, [____]]]
SD-03 Product Data
Manufacturer's Catalog Data[; G[, [____]]]
SD-04 Samples
Finish and Color Samples[; G[, [____]]]
SD-06 Test Reports
Certified Test Reports[; G[, [____]]]
SD-07 Certificates
Manufacturer's Product Warranty[; G[, [____]]]
1.4
QUALITY ASSURANCE
1.4.1
1.4.1.1
Qualifications
Installer Qualifications
Provide documentation of Installer experience [as determined by Contractor]
to perform work of this section, who has specialized in the installation of
SECTION 08 41 13
Page 7
work similar to that required for this project, and who is acceptable to
product manufacturer.
1.4.1.2
Manufacturer Qualifications
Manufacturers are acceptable providing they meet the requirements specified
in this section and project drawings.
Ensure manufacturer is capable of providing field service representation
during construction, approving acceptable installer and approving
application method.
1.4.2
Single Source Responsibility
When aluminum entrances are part of a building enclosure system, including
storefront framing, windows, curtain wall system and related products,
provide building enclosure system products from a single source
manufacturer.
Provide design, structural engineering, and custom fabrication for door
portal system and supply of all components, materials, and products based
on a single manufacturer of sole responsibility. Provision of products
from numerous sources for site assembly without complete single source
design and supply responsibility is not acceptable. Work items and
components to be fabricated or supplied by single source are:
**************************************************************************
NOTE: Edit the following list to reflect components
required for glass wall and door portal assembly.
Verify that sole source responsibility requirement
is included in other sections.
**************************************************************************
a.
Door assemblies to be installed in door portal as specified in [Section
08 11 16 ALUMINUM DOORS AND FRAMES][_____].
b.
Glazed wall to be constructed around door portal as specified in [this
Section][_____].
c.
Door operating hardware to be installed on or within door portal as
specified in Section 08 71 00 DOOR HARDWARE.
d.
Glass as specified in [Section 08 81 00 GLAZING][_____].
1.5
1.5.1
DELIVERY, STORAGE, AND HANDLING
Ordering
Comply with manufacturer's ordering instructions and lead-time requirements
to avoid construction delays.
1.5.2
Packing, Shipping, Handling and Unloading
Deliver materials in manufacturer's original, unopened, undamaged
containers with identification labels intact.
1.5.3
Storage and Protection
Store materials protected from exposure to harmful weather conditions.
SECTION 08 41 13
Page 8
Handle storefront material and components to avoid damage. Protect
storefront material against damage from elements, construction activities,
and other hazards before, during and after storefront installation.
1.6
PROJECT / SITE CONDITIONS
1.6.1
Field Measurements
Verify actual measurements/openings by field measurements before
fabrication; show recorded measurements on shop drawings. Coordinate field
measurements, fabrication schedule with construction progress to avoid
construction delays.
PART 2
2.1
PRODUCTS
SYSTEM DESCRIPTION
This Specification includes aluminum entrances, glass and glazing, door
hardware, and components.
Type of Aluminum Entrance includes:
Impact Resistance Entrances; medium stile, 88.9 mm 3-1/2 inch vertical
face dimension, 44.45 mm 1-3/4 inch depth, interior structural silicone
glazed, high traffic/impact resistant applications.
2.1.1
Design Requirements for Aluminum (Entrances and Components)
Design, size components, and install door portal system to withstand these
loads without breakage, loss, failure of seals, product deterioration, and
other defects, AAMA 503.
a.
Dead and Live Loads: Determined by ASCE 7 and calculated in accordance
with applicable codes.
b.
Seismic Loads: Design and install system to comply with applicable
seismic requirements for project location as defined by Section 1613 of
the International Building Code (IBC).
c.
Effects of applicable wind load acting inward and outward normal to
plane of wall in accordance with ASTM E330.
d.
Thermal Loads And Movement:
(1)
Ambient Temperature Range: [ [67][_____] degrees C.][
[120][_____] degrees F.]
(2)
Material Surfaces Range: [ [100][_____] degrees C.][ [180][_____]
degrees F.]
e.
Provide and install weatherstripping, exterior gaskets, sealants, and
other accessories to resist water and air penetration.
f.
Impact Protective Systems ASTM E1886.
2.1.1.1
Material Standard
ASTM B221 ASTM B221M; 6063-T5 alloy and tempered.
SECTION 08 41 13
Page 9
Provide door stile and rail face dimensions of the entrance doors as
follows:
Vertical Stile
Top Rail
Bottom Rail
8.89 cm
8.89 cm
16.51
Vertical Stile
Top Rail
Bottom Rail
3-1/2 inches
3-1/2 inches
6-1/2 inches
Provide major portions of the door members at 0.3175 cm.125 inches nominal
in thickness and glazing molding to be 0.127 cm .050 inches thick.
2.1.1.2
Tolerances
Reference to tolerances for wall thickness and other cross-sectional
dimensions of entrance members are nominal and in compliance with Aluminum
Standards and Data, published by The Aluminum Association.
Provide either EPDM elastomeric extrusions or thermoplastic elastomer
glazing gaskets. Structural silicone sealant is required.
2.1.2
Performance Requirements
2.1.2.1
Air Infiltration
Submit certified test reports showing compliance with specified performance
characteristics as follows:
a.
For single acting offset pivot, butt hung or continuous geared hinge
entrances in the closed and locked position, test the specimen in
accordance with ANSI/BHMA A156.10, and ASTM E283 at a pressure
differential of 7.7.67 kilogram/square meter 1.57 psf for pairs of
doors; maximum infiltration for a pair of 2.13 meter by 2.44 meter 7
foot - 0 inch by 8 foot - 0 inch entrance doors and frame is 0.034
cubic meters per minute/square meter 1.2 cfm/ft2.
b.
Maximum allowable infiltration, for a completed storefront system is
not to exceed 0.0017 cubic meters/square meter 0.06 cfm/square foot
when tested in accordance with ASTM E1424 at differential static
pressure of 299 Pa 6.24 psf.
2.1.2.2
Wind Loads
Provide completed storefront system capable of withstanding wind pressure
loads, normal to the wall plane indicated, as follows:
a.
b.
Exterior Walls
(1)
Positive Pressure:
[_____] kilogram/square meter [_____] psf
(2)
Negative Pressure:
[_____] kilogram/square meter [_____] psf
Interior Walls: (pressure acting in either direction)
kilogram/square meter [_____] psf
SECTION 08 41 13
Page 10
[_____]
2.1.2.3
Deflection
Submit certified test reports showing compliance with specified performance
characteristics as follows:
The maximum allowable deflection in any member when tested in
accordance with ASTM E330 with allowable stress in accordance with AA
Specifications for Aluminum Structures is L/175 or 19.1 mm 3/4 inches
maximum.
2.1.2.4
Condensation Resistance and Thermal Transmittance
Submit certified test reports showing compliance with specified performance
characteristics as follows:
a.
b.
U-Value Requirements:
(1)
Perform test in accordance with AAMA 1503 procedure and on the
configuration specified therein.
(2)
Thermal Transmittance ("U" Value) maximum [_____][3.69 W/sqm/deg
C] at [_____][24.14] kmph [_____][0.65 (6250) BTU/hr/sf/deg F] at
[15] mph exterior wind.
CRF Class Requirements:
(1)
Perform test in accordance with AAMA 1503.
(2)
Condensation Resistance Factor Requirements (CRF) minimum [_____].
2.1.2.5
Water Infiltration
Submit certified test reports showing compliance with specified performance
characteristics as follows:
System is designed to provide no uncontrolled water when tested in
accordance with ASTM E331 at a static pressure of 956 Pa 8 psf.
2.2
2.2.1
FABRICATION
Entrance System Fabrication
Provide door corner construction consisting of mechanical clip fastening,
SIGMA deep penetration plug welds and 2.8575 cm 1-1/8 inch long fillet
welds inside and outside of all four corners. Provide hook-in type
exterior glazing stop with EPDM glazing gaskets reinforced with
non-stretchable cord. Provide interior glazing stop mechanically fastened
to the door member incorporating a silicone compatible spacer used with
silicone sealant.
Accurately fit and secure joints and corners. Make joints hairline in
appearance. Prepare components with internal reinforcement for door
hardware. Arrange fasteners and attachments to conceal from view.
2.2.2
Shop Assembly
Fabricate and assemble units with joints only at intersection of aluminum
members with hairline joints; rigidly secure, and sealed in accordance with
manufacturer's recommendations.
SECTION 08 41 13
Page 11
2.2.2.1
Welding
Conceal welds on aluminum members in accordance with AWS recommendations or
methods recommended by manufacturer. Members showing welding bloom or
discoloration on finish or material distortion will be rejected.
2.2.3
Fabrication Tolerance
Fabricate and assemble units with joints only at intersection of aluminum
members with hairline joints; rigidly secure, and sealed in accordance with
manufacturer's recommendations.
Fabricate aluminum entrances in accordance with entrance manufacturer's
prescribed tolerances.
2.2.3.1
Material Cuts
Square to 0.8 mm 1/32 inch off square, over largest dimension;
proportionate amount of 0.8 mm 1/32 inch on the two dimensions.
[2.2.3.2
Maximum Offset At Consecutive Members
0.4 mm 1/64 inch in alignment between two consecutive members in line, end
to end.
][2.2.3.3
Maximum Offset At Glazing Pocket Corners
0.4 mm 1/64 inch between framing members at glazing pocket corners.
]2.2.3.4
Joints
(Between adjacent members in same assembly:
adjacent member.
2.2.3.5
Hairline and square to
Variation
In squaring diagonals for doors and fabricated assemblies:
2.2.3.6
Flatness
For doors and fabricated assemblies:
neutral plane.
2.3
2.3.1
1.6 mm 1/16 inch.
1.6 mm plus/minus 1/16 inch of
ACCESSORIES
Fasteners
Provide stainless steel where exposed.
2.3.2
Perimeter Anchors
When steel anchors are used, provide insulation between steel material and
aluminum material to prevent galvanic action.
SECTION 08 41 13
Page 12
2.3.3
Standard Entrance Hardware
2.3.3.1
Weatherstripping
Equip meeting stiles on pairs of doors with an adjustable astragal
utilizing wool pile with polymeric fin.
Provide door weatherstripping on a single acting offset pivot or butt hung
door and frame (single or pairs) comprised of a thermoplastic elastomer
weatherstripping on a tubular shape with a semi-rigid polymeric backing.
Provide Sill Sweep Strips: EPDM blade gasket sweep strip in an aluminum
extrusion applied to the interior exposed surface of the bottom rail with
concealed fasteners. (Provide as necessary to meet specified performance
tests.)
2.3.3.2
Threshold
Provide extruded aluminum threshold, one piece per door opening, with
ribbed surface.
2.3.3.3
Offset Pivots
Provide manufacturer's standard top and bottom pivots with one intermediate
offset pivot.
2.3.3.4
Panic Device
Provide manufacturer's recommended standard panic hardware.
2.3.3.5
Closer
Provide surface closer only per ANSI/BHMA A156.4.
2.3.3.6
Security Lock/Dead Lock
Provide A/R MS 1850A lock with (2) A/R 1871 cylinder operated flush bolts.
2.3.3.7
Cylinder(s)/Thumb-turn
Provide manufacturer's recommended standard.
2.3.3.8
Cylinder Guard
Manufacturer standard.
2.4
2.4.1
RELATED MATERIALS
Sealants
[ Refer to Section 07 92 00 JOINT SEALANTS.
AAMA 800.
2.4.2
]Ensure all sealants conform to
Glass
Refer to Section 08 81 00 GLAZING.
SECTION 08 41 13
Page 13
PART 3
3.1
EXECUTION
EXAMINATION
3.1.1
Site Verification of Conditions
Verify substrate conditions (which have been previously installed under
other sections) are acceptable for product installation in accordance with
manufacturer's instructions.
Verify openings are sized to receive storefront system and sill plate is
level in accordance with manufacturer's acceptable tolerances.
3.2
INSTALLATION
Install entrance system in accordance with manufacturer's instructions and
AAMA storefront and entrance guide specifications manual. Attach to
structure to permit sufficient adjustment to accommodate construction
tolerances and other irregularities. Provide alignment attachments and
shims to permanently fasten system to building structure. Align assembly
plumb and level, free of warp and twist. Maintain assembly dimensional
tolerances aligning with adjacent work.
Set thresholds in bed of mastic and secure. Protect aluminum members in
contact with masonry, steel, concrete, or dissimilar materials using
nylatron pads or bituminous coating. Shim and brace aluminum system before
anchoring to structure. Verify weep holes are open, and metal joints are
sealed in accordance with manufacturer's installation instructions. Seal
metal to metal joints using sealant recommended by system manufacturer.
3.2.1
Preparation
Field verify dimensions prior to fabricating door portal assembly
components.
Coordinate requirements for locations of blockouts for anchorage of door
portal columns and other embedded components with Section 03 30 00
CAST-IN-PLACE CONCRETE.
Coordinate erection of door portal with installation of surrounding glass
wall and door assemblies. Ensure adequate provision is made for support
and anchorage of assembly components.
**************************************************************************
NOTE: Edit the following list to reflect components
required for glass wall and door portal assembly.
Verify that sole source responsibility requirement
is included in other sections.
**************************************************************************
Coordinate electrical requirements for [automatic door
assemblies][electrified door hardware] to ensure proper power source,
conduit, wiring, and boxes.
3.2.1.1
Adjacent Surfaces Protection
Protect adjacent work areas and finish surfaces from damage during product
installation.
SECTION 08 41 13
Page 14
3.2.1.2
Aluminum Surface Protection
Protect aluminum surfaces from contact with lime, mortar, cement, acids,
and other harmful contaminants.
3.2.2
Adjusting
Adjust operating hardware for smooth operation, and as recommended by the
manufacturer.
3.2.3
Related Products Installation Requirements
3.2.3.1
Sealants (Perimeter)
Refer to Section 07 92 00 JOINT SEALANTS.
3.2.3.2
Glass
Refer to Section 08 81 00 GLAZING.
3.2.3.3
Reference
ANSI Z97.1, 16 CFR 1201 and GANA Glazing Manual.
3.3
3.3.1
PROTECTION AND CLEANING
Protection
Protect installed product's finish surfaces from damage during
construction. Protect aluminum storefront system from damage from grinding
and polishing compounds, plaster, lime, acid, cement, or other harmful
contaminants.
3.3.2
Cleaning
Repair or replace damaged installed products. Clean installed products in
accordance with manufacturer's instructions prior to owner's acceptance.
Remove construction debris from project site and legally dispose of debris.
3.4
WARRANTY
Submit [three] [_____] signed copies of manufacturer's product warranty for
entrance system as follows:
Warranty Period: [Five] [_____] years from Date of Substantial
Completion of the project, provided that the Limited Warranty begins in
no event later than [six] [_____] months from date of shipment by
manufacturer. In addition, support welded door corner construction
with a limited lifetime warranty for the life of the door under normal
use.
Ensure Warranty language is identical to "As Approved" version of the
sample warranty submitted and returned from the Contracting Officer.
-- End of Section --
SECTION 08 41 13
Page 15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement