Halsey Taylor 5701.C Water Coolers-Drinking Fountain Owner Manual
Advertisement
Advertisement
5701*C FOUNTAIN
Halsey Taylor Owners Manual
Wall Mount Fountain
INSTALLER
Halsey Taylor Fountains are among the easiest to install Fountains on the market today. To assure you install these models easily and correctly,
PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE
INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH
PLUMBING, ELECTRICAL, AND OTHER APPLICABLE CODES. After installation, leave these instructions with the Fountain for future reference.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER
LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY
FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING
AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE
WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN
FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE
FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.
1. Water supply 3/8" O.D. unplated copper tube. Waste 1-1/4" O.D. Contractor to supply waste trap and service
stop valve in accordance with local code.
2. Connecting lines to be made of unplated copper and should be thoroughly flushed to remove all foreign matter
before being connected to fountain. This fountain is manufactured in such a manner that it does not in any
way cause taste, odor, color, or sediment problems.
3. These products are designed to operate on 20 psig to 105 psig supply line pressure. If inlet pressure is above
105 psig, a pressure regulator must be installed in the supply line. Any damage caused by reason of
connecting this product to supply line pressures lower than 20 psig or higher than 105 psig is not covered by
warranty.
PAGE 1 97593C (2/00)
D = MOUNTING HOLES FOR BASIN HANGER STRAP
5701*C FOUNTAIN
FINISHED FLOOR PISO ACABADO PLACHER FINI
97593C (2/00) PAGE 2
5701*C FOUNTAIN
HANGER BRACKET AND TRAP INSTALLATION
1. Mount the hanger bracket and trap as shown in Fig 1.
NOTE: Hanger bracket MUST be supported securely. Add fixture support carrier if wall will not provide adequate support.
IMPORTANT:
- 5-5/8" dimension from centerline of unit to centerline of trap must be maintained for proper fit.
- Anchor hanger securely to wall using all mounting holes.
INSTALLATION OF FOUNTAIN
2. Hang the fountain on the hanger bracket. Be certain the hanger bracket is engaged properly in the basin.
3. Remove the access panel on the underside of the fountain and set aside.
4. Install a 3/8" O.D. unplated copper water line between the service stop valve and fountain. Remove burr from outside of water
line. Insert the 3/8" O.D. water line to a positive stop approximately 3/4 inch (See figures 2 and 3). DO NOT SOLDER TUBES
INSERTED INTO THE STRAINER AS DAMAGE TO THE O-RINGS MAY RESULT.
5. NOTE: If required, the 1/4 O.D. water inlet line to fountain may be cut to a desired length. However, if water line is cut, all burrs
must be removed from outside of tube before inserting into the strainer.
6. Remove the slip nut and gasket from the trap and install them on the fountain waste line, making sure that the end of the waste line
fits into the trap. Assemble the slip nut and gasket to the trap and tighten securely.
START UP
7. Turn on the building water supply and check all connections for leaks.
8. Depress push bar until all air is bled from fountain water system. A steady stream flow assures all air is removed.
9. Stream height is factory set at 45-50 PSI. If supply pressure varies greatly from this, readjust stream height to approximately 1-1/2"
above the bubbler guard by turning adjustment screw, accessible by removing front push panel. (See Fig. 4 & 5)
10. Recheck all water and drain connections with water flowing through system.
11. Replace the access panel and secure by re-tightening all screws.
12. Water Valve Mechanism
ADJUSTMENT PROCEDURE:
- Turn adjustment screw "Counter-clockwise" until water flow from bubbler starts.
- Turn adjustment screw "Clockwise" until water flow stops, then turn an additional 1/2 turn.
NOTE: Adjustments stated above are as viewed from underneath unit.
OPERATION OF QUICK CONNECT FITTINGS
Simply Push In Tube
To Attach
Tube Is Secured In
Position
Push In Collet To
Release Tube
A B C
Pushing Tube In Before
Pulling It Out Helps To
Release Tube.
FIG. 2
1/4" O.D. TUBE
WATER INLET
TO COOLER
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY
BUILDING WATER
INLET
NOTE: WATER FLOW
DIRECTION
FIG. 3
SERVICE STOP
(NOT FURNISHED)
PAGE 3
CORRECT STREAM HEIGHT
FIG. 4
97593C (2/00)
ITEM NO.
13
14
15
16
9
10
11
12
7
8
5
6
3
4
1
2
21
22
23
24
25
17
18
19
20
ITEMIZED PARTS LIST
PART NO.
DESCRIPTION
15005C
100322740560
101514331640
26664C
22900C
22901C
23003C
26976C
26600C
28079C
28083C
40045C
50212C
50986C
51531C
51544C
55859C
61314C
70935C
55996C
15008C
40575C
50074C
40572C
55994C
Retaining Nut
Gasket - Bubbler
Push Bar Insert
Basin
Bracket - Front Push
Bracket - Side Push
Bracket - Regulator Mounting
Panel - Bottom Dispenser
Panel - Front (Stainless Steel)
Panel - Left Side (Stainless Steel)
Panel - Right Side (Stainless Steel)
Hex Nut
Rivet - Drive Type
Regulator Holder
Pivot Block
Bubbler - Chrome
Push Bar
Regulator
Screw - Shoulder x 1/2" Lg.
Strainer
Bubbler Nipple
Strainer & Ferrule Assy
Gasket - Tailpipe
Tailpipe
Tube-Poly 1/4 x .040 Wall
5701*C FOUNTAIN
TROUBLE SHOOTING AND MAINTENANCE
Orifice Assy: Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposists may be removed from the orifice with a small round file not over 1/8" diameter or small diameter wire. CAUTION:
DO NOT FILE OR CUT ORIFICE MATERIAL.
Stream regulator: If orifice is clean, regulate flow as in "START UP" instructions on page 3. If replacement is necessary, see parts list for correct regulator part number.
22
23
24
FIG. 6
SEE FIG. 6
4
16
FIG. 5
20
12
10
6 2
21
25
14
18
1
15
9
STREAM HEIGHT ADJUSTMENT
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
PRINTED IN U.S.A.
97593C (2/00)
5
13
7
8
13
ADJUST THIS SCREW (ITEM 19) TO ELIMINATE
MECHANISM "FREE PLAY" OR CONTINUOUS
FLOW FROM BUBBLER CONDITIONS.
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
PAGE 4
3
11
17

Public link updated
The public link to your chat has been updated.
Advertisement