Casablanca Twain Owner`s manual

Casablanca Twain Owner`s manual
Twain™ Ceiling Fan Owner’s Manual
Congratulations on your purchase of a Casablanca ceiling fan!
Your new fan will be a beautiful addition to your home, keeping you comfortable throughout
the year. The true appreciation of a Casablanca ceiling fan is only complete when put
into actual use. Great time and care have been taken to construct and enhance what are
otherwise functional appliances. Beauty is found in the integrity, craftsmanship, and attention
to detail. Thank you for looking for the
nameplate that defines ceiling fans.
Contents
Parts Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Product Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Mounting Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Fan Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Structural Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Sloped Ceiling Installations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing the Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Assembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Attaching the Crossbar Mounting Bracket. . . . . . . . . . . . . . . . . . . . . . . . 9
Attaching the Canopy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installing the Fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Assembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Hanging the Fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Connecting the Wires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Installing the W-81 Wall Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Operating the W-81 Wall Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Attaching the Canopy Hatch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Installing the Blades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Assembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Attaching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installing the Light Fixture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Attaching the Light Fixture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Attaching the Halogen Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Attaching the Glass Shade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Problems and Possible Remedies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Care Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
PN C2543001-TC1108
1
Twain
™
PLEASE INSPECT ALL PACKAGING PRIOR TO DISCARDING!
Your Casablanca fan was crafted with pride and care and inspected thoroughly prior
to shipment. Before you begin to assemble and install your Casablanca fan, remove all
parts from the carton and check them against the Parts Guide in this manual.
Make sure all parts are included in the box
using the Parts Guide on the following pages.
• Always turn power to the ceiling fan OFF before
replacing lightbulbs or working on your fan.
If there are missing or broken parts:
• Never insert anything into the path of the
fan blades while the fan is in operation.
• Call 1-888-227-2178 Monday through Friday,
7 a.m. to 4 p.m. PST. Your request will be
handled immediately. Replacement parts
will be sent to you via Federal Express.
• Never install a fan over a pool or spa.
• Never operate a fan that has been
damaged in any way.
Proper Parts Handling
Install the fan according to the
instructions in this manual.
• Do not remove lightbulbs from their packaging
until you are ready to install them.
If the fan does not work:
• Before discarding packaging materials, be
certain that all parts have been removed.
• Use a clean, dry paintbrush to remove small
Styrofoam pieces that may remain after unpacking.
• Refer to the Troubleshooting Tips
in this Owner’s Manual.
• Call Technical Support at 1-888-227-2178.
• Do not brush Styrofoam into wiring cavities.
• Contact your local Authorized Service Center.
• The blades in each pack are matched for
equal weight to assure smooth fan operation.
If more than one fan is being installed, do
not mix blades from different cartons.
Our Web site at www.casablancafanco.com contains
additional information on Casablanca products,
troubleshooting, and Authorized Dealer or Service
Centers. Please do not return this product to the store.
• When cleaning, painting, or working near your
fan, be cautious of the fan and blades.
RECORD MODEL AND SERIAL NUMBERS BEFORE INSTALLATION!
Please take a moment to locate the model number and serial number from your fan (see below) and record this
information on the Warranty page inside the front cover of your Owner’s Manual if it does not appear there already.
These numbers are found on the motor identification plate affixed to the fan motor in the location shown below:
Motor Identification Plate
Twain®
TYPE HANGER TYPE
POMONA, CA
SERIAL No.: DJ06 2237
C25G624F
2
DJ01 1151 MODEL #C25G624F
Serial Number
Model Number
Twain
™
Parts Guide
Item #
Description
Picture (not to scale)
Quantity
1.
Motor Housing
1
2.
Crossbar Mounting Bracket
1
3.
Right-Angle Screwdriver
1
4.
Lag Screw and Washer
1
5.
1" x 8-32 Round-Head Screws and Washers
2
6.
Canopy and Hatch
1
7.
2½" x 8-32 Canopy Screws and Lock Washers
5
8.
2¼" Perma•Lock™ Downrod and Ball Assembly
1
9.
Allen Wrench
1
10.
Wire Nuts
4
11.
Light Fixture
1
12.
Light Fixture Screws
4
13.
Halogen Downlight Bulbs, 50W
2
14.
Blades
5
15.
Blade Iron Plate Screws
21
3
Twain
™
Item #
4
Description
Picture (not to scale)
Quantity
16.
Blade Iron Plates
5
17.
Blade Irons
5
18.
Blade Iron Screws
11
19.
Balance Kit
1
20.
Light Adapter Plate
1
21.
Light Adapter Screws
3
22.
Incandescent Uplight Bulbs, 25W
6
23.
Glass Shade
1
24.
Finial
1
25.
W-81 Wall Control
1
Twain
™
Product Specifications
Model name:
Model number:
ETL Rating:
Dimensions:
Twain®
C25GXXXF
Damp
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference
received, including interference that
may cause undesired operation.
A=
B=
C=
D=
E=
Weight:
Motor Type:
Motor Size:
Blade Span:
Blade Iron Pitch:
No. of Blades:
Technology:
Lightbulbs:
11.9"
16.7" NOTE: Dimension
3"
B includes light
16.2" fixture and glass.
5.6"
45 lbs.
XTR200™
200mm x 30mm
60"
14˚
5
W-81 wall control
(6) 25-watt B10 incandescent
(2) 50-watt T4 halogen
Airflow:
8,173 cfm
Electricity Use*:
97 watts
Airflow Eficiency*: 84.3 cfm/watt
*Performance data is for fan only. No lighting
wattage is included.
This equipment has been tested and found to comply with
the limits for a class B digital device, pursuant to Part 15
of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communication.
However, there is no guarantee that the interference will
not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
5
Twain
™
Safety Considerations
Safety and the proper operation of your Casablanca
fan both require a thorough knowledge of the
product and proper installation; therefore, before
attempting to install and operate your Casablanca
fan, read this Owner’s Manual completely and
carefully. Retain this manual for future reference.
Fuse Box
(Remove fuse for the
circuit you will be
working on)
Circuit Breaker
(Trip breaker for the
circuit you will be
working on)
ÑÑCAUTION: RISK OF ELECTRICAL SHOCK!
Turn off all electricity at the circuit breaker
or fuse box before attempting any
installation procedure. Installation is to be
in accordance with the National Electrical
ANSI/NFPA 70-1999 and local codes. If
you are unfamiliar with the wiring codes,
contact a qualified electrician. To avoid
overheating and possible damage to
other equipment, do not install control
to a receptacle, fluorescent light fixture,
operating appliance, or transformersupplied appliance.
• This ceiling fan requires a grounded electrical supply
of 120 VAC, 60 Hz and a minimum of 15-amp
circuit. The maximum current required for the fan
with light fixture is 3.2 amps (382 watts). The fan
uses about 1.1 amps (132 watts). Maximum light
current is about 2.1 amps (190 watts) of lighting.
• Where wire nuts are employed, be sure all
bare wires are fully inserted into the metal wire
connectors inside the plastic wire nut covering.
• When installing the canopy, light kit, and wall
controls, make sure all wires are carefully
tucked away and that no wires are pinched.
• The fan must be supplied with three
independent 120V AC supply wires to provide
power for the fan, the light, and neutral.
ÑÑWARNING: To reduce the risk of
personal injury or damage to the fan,
do not bend the blade brackets or insert
foreign objects in between the rotating fan
blades.
ÑÑWARNING: To reduce the risk of fire or
electric shock, do not use this fan with any
solid-state control device. Use only the
control provided with or recommended for
this fan.
6
from wall to
end of blade
18" �
from wall to
center of fan
70"�
84" � from bottom edge
of blade to floor
Dimensions indicated are the minimum
allowable for proper installation.
Twain
™
Mounting Guidelines
Structural Support
Before mounting your Casablanca fan, read the
following helpful recommendations. Location,
fan size, and structural support are important
factors to consider before installation.
Installing a New Ceiling Fixture Outlet Box
Location
Ceiling fans have practical uses in almost every
room in your home. We suggest you follow
these mounting recommendations as you decide
where to install your Casablanca fan.
• For safety reasons, the fan blades must
be a minimum of 7’ above the floor.
• Do not locate the fan in a doorway
or above a swinging door.
• In bedrooms, fans work best when
mounted above the foot of the bed.
• Over pool tables, be sure to provide plenty of
clearance to avoid damage from pool cues.
If you do not have an existing fixture located where
you wish to place your Casablanca fan, an approved
ceiling fixture outlet box must be installed and wired.
Using Existing Ceiling Fixture Outlet Box
After turning the power OFF at its source (either the circuit
breaker or fuse box), lower the old fixture and disconnect
the wiring. Check the ceiling fixture outlet box to be sure
it is marked “Approved for Ceiling Fan Mounting.” If it is
not, a new box must be installed. For new construction,
use an approved ceiling fixture outlet box with the rating
“50 lbs. or less”. Ensure that outlet box is mounted to a
joist or stud beam. If not, a 2x4 stud must be installed.
ÑÑWARNING! To reduce the risk of fire,
electrical shock, or personal injury, mount
to outlet box marked “Acceptable Fan
Support of 22.7 kg (50 lbs.) or less” using
the mounting hardware provided with the
outlet box.
• In kitchens be sure to allow for open
cupboard doors to clear the fan blades.
• Do not install a fan close to or over a pool or spa.
High humidity combined with corrosive gases
will destroy the finish and warp the blades.
Fan Size
Variable fan speed capability permits the use of
a full-size fan even in smaller rooms. For very
large rooms, two fans may be needed.
When to Use a Lag Screw
A lag screw is required under two conditions: the
fan weighs 36 lbs. or more or the existing ceiling
fixture outlet box needs to be modified for a ceiling
fan application (for example, you are replacing an
existing light fixture). We recommend that the ceiling
box be of sufficient capacity to support the weight
of the fan and light fixture under any conditions.
NOTE: The Twain weighs 45 lbs., so use of a
lag screw is required.
7
Twain
™
Sloped Ceiling Installations
Suggested Extension Downrod Lengths
Ceiling Height
Downrod Length
When to Use an Extension Downrod
8' 0"
standard
For optimum performance and appearance, use
an extension downrod with your Casablanca
fan when installing on high (cathedral) ceilings
or sloped ceilings. Casablanca offers accessory
downrods in increments of 6" up to 5’. See your
Authorized Casablanca Dealer for details.
8' 6"
standard
9' 0"
6"
Calculation of Ceiling Angle
Use the tear-off Ceiling Angle Template card inserted
in this manual. It provides you with a simple “go” or
“no go” for installing your fan on a sloped ceiling.
Extension
Downrod
Maximum angle
of Hang-Tru®
canopy = 32º
Blades must be a
minimum of 7 feet
above the floor
7' minimum
EXAMPLE 1
EXAMPLE 2
EXAMPLE 3
This slope is less than 32º.
It is OK to install your fan.
This slope is 32º. This is the
maximum slope that will allow the
fan to hang straight down. It is OK
to install your fan.
This slope is more than 32º. Your fan
will not hang straight down, so an
adaptor is necessary. Contact your
local Authorized Casablanca Dealer to
purchase a Sloped Ceiling Adapter.
NOTE: The fan may wobble or vibrate if the
downrod length is not long enough and the
inside blade is too close to the downslope or side
wall. Extending the downrod length usually will
solve this problem.
8
9' 6"
12"
10' 0"
12"
11' 0"
18"
12' 0"
24"
13' 0"
36"
14' 0"
48"
15' 0"
60"
Twain
™
Installing the Mounting Hardware
Hardware (not to scale)
Crossbar Mounting
Bracket (1)
Lag Screw and Washer (1)
Canopy Hatch (1)
Canopy (1)
Assembling
1” x 8-32 Round-Head Screws
and Washers (2)
Right Angle Screwdriver
2½” x 8-32 Canopy Screws (4) and Lock Washers (5)
Steps 3-4
Joist
1
Determine the need for a lag screw based
on the Mounting Guidelines previously described.
If in doubt whether you need to install the lag
screw, consult a qualified electrician.
Ceiling wiring
2
Ceiling fixture
outlet box
(ceiling fan rated)
If a lag screw is required, remove the plug
in the center of the ceiling fixture outlet box. If the
outlet box does not have a plug, drill a ½ inch hole
for the lag screw. After drilling a hole for the lag
screw, drill a ¼ inch hole 3 inches deep through the
beam supporting the ceiling fixture outlet box.
GREEN ground wire
Attaching the Crossbar Mounting Bracket
3
To install the crossbar mounting bracket,
route the outlet box wires along side of the crossbar
mounting bracket. (see Step 5 image) Attach the
crossbar mounting bracket to the outlet box with
the set of two round-head screws and washers. Use
caution when installing the screws and washers. Do
not pinch the outlet box wires in the washers.
Crossbar mounting
bracket
(ridge side down)
Washers (2)
1” x 8-32 Roundhead screws (2)
Lag screw and
washer (1)
ÑÑCAUTION: To reduce the risk of personal
injury, use only the mounting hardware
provided with an approved outlet box (not
included) to install the crossbar mounting
bracket.
9
Twain
™
4
To install the lag screw (if needed), slide the
remaining washer onto the lag screw. Pass the
lag screw through the center hole in the crossbar
mounting bracket. Secure the lag screw into the
guide hole, tightening until the ceiling fixture outlet
box is firmly mounted to the support beam.
Step 5
Attaching the Canopy
5
To install the canopy hardware, set aside the
canopy hatch and attach the canopy to the crossbar
mounting bracket with three of the canopy screws
and lock washers. Using the right-angle screwdriver
provided, tighten each screw until the canopy hardware
is firmly mounted to the crossbar mounting bracket.
Canopy
NOTE: On a sloped ceiling, align the canopy
opening with the top or peak of the room.
Canopy hatch
Lock washers (4)
NO DRILL
Canopy screws (4)
10
Twain
™
Installing the Fan
Hardware (not to scale)
Perma•Lock™ Downrod and
Ball Assembly (1)
Allen Wrench (1)
Wire Nuts (4)
Canopy Hatch (1)
Canopy (1)
Incandescent Uplight Bulbs, 25W (6)
Assembling
1
2
2½" x 8-32 Canopy Screw (1)
and Lock Washer (1)
Step 1
Paper motor
shield
Remove the paper shield from the motor.
Examine the interior of the motor coupling. If
the end of the set screw is inside the motor coupling
space, use the Allen wrench to loosen the screw.
Step 2
Set screw - CORRECT PLACEMENT
Allen wrench
Set screw - INCORRECT PLACEMENT
Allen wrench
11
Twain
™
3
Route the fan wires through the
downrod and ball assembly.
sTEPs 3-4
Downrod and
ball assembly
4
Insert the downrod into the motor coupling
and turn clockwise. When the downrod is securely in
place, re-tighten the set screw with the Allen wrench
until it will not turn any further. Test the stability of
the downrod assembly by attempting to unscrew the
downrod from the motor coupling. If the downrod turns
in either direction, the set screw should be tightened.
Set screw
Allen
wrench
thread designed to lock completely when
correctly installed. Failure to fully lock in
the downrod before securely tightening
the set screw may cause the fan to
separate from the downrod and fall during
normal operation.
12
Step 5
Screw in the six light bulbs.
Motor
wires
Motor
coupling
ÑÑCAUTION: The downrod has a tapered
5
Tapered
thread
Twain
™
Hanging the Fan
Step 8
8
Hold the motor housing with both hands. Insert
the ball of the downrod into the canopy opening.
Check to ensure that the wires are not pinched. Rotate
the motor housing until the slot in the downrod ball
locks into the pin opposite the canopy opening.
Ball
Slot
Pin
Connecting the Wires
9
Trim the extra length from the motor wires. Be
certain to leave at least 6 inches of wire above the
downrod. Use a wire stripper (not included) to strip
½-inch of insulation from the end of each trimmed wire.
Steps 9-10
RED and
BLUE wires
10
To attach the fan wires to the ceiling
fixture wiring, match the wire colors as described
below, hold the bare ends of the wires side by side,
and fully insert the wires into the wire nut. Secure
by rotating the wire nut in a clockwise motion.
2 BLACK wires
2 WHITE wires
3 GREEN wires
Connect wires in the following order:
• GREEN wires from mounting plate and downrod
assembly of fan to GROUND wire of power source.
Wire nut
• WHITE fan wire to WHITE neutral
wire from ceiling outlet box.
• BLACK power wire from fan to BLACK
power wire in ceiling outlet box.
• BLUE D1 optional fan wire to RED power wire
(second hot wire) in ceiling outlet box.
NOTE: If the color of your ceiling wires differs
from that described, consult an electrician.
Inspect each wire nut to ensure that no bare wire is visible.
Test the connection by gently pulling on the wires. The wire
nuts should stay firmly in place, covering the bare ends.
13
Twain
™
Installing the W-81 Wall Control
Hardware (not to scale)
W-81 Wall Control
(assembled)
Wall Plate (2 colors included)
Wall Plate
Screws (4)
Switch Box
Screws (2)
The fan must be supplied with three independent 120V
AC wires to provide power for the fan, light, and neutral.
ÑÑCAUTION: Ensure power is turned
OFF at the breaker or fuse panel before
beginning wall control installation.
NOTE: The W-81 wall control is designed to
replace a standard wall switch and fits wall
boxes (metal or plastic) with a depth of more
than 2".
1
Remove the screws and switch plate from the
existing wall switch box, and pull the switch away
from the box to expose the wire connections.
2
Disconnect the three wires from the existing
switch and remove the switch from the wall box.
The ends of the wires in the wall box may need to
be stripped before installing the new control.
NOTE: The wire nuts provided are only
suitable for use with copper wire. Use wire
nuts to join one 14-gauge wire with one 16- or
18-gauge wire.
14
Wall Control (1)
Wire Nuts (4)
Twain
™
3
To attach the wires in the wall box to the W-81
wall control wires, match the wire colors as described
below, hold the bare ends of the wires side by side,
and fully insert the wires into the wire nut. Secure
by rotating the wire nut in a clockwise motion.
Step 3
Connect wires in the following order:
• GREEN GROUND conductor from the wall box to
the GREEN wire from wall control (labeled GRD)
• BLACK wire from fan in the wall box to
YELLOW wire on wall control (labeled FAN)
• RED wire from fan in the wall box to RED
wire on the wall control (labeled LIGHT)
Note: BLUE D1 optional fan wire can be
connected to RED power wire in ceiling outlet
box.
• BLACK wire from the source of power
(HOT WIRE) wire in the wall box to BLACK
wire on wall control (labeled LIVE)
BLACK wire
(LIVE)
W-81 wall
control
(back view)
NOTE: If the colors of your wiring differ from
that described, consult an electrician.
Inspect each wire nut to ensure that no bare wire is visible.
Test the connection by gently pulling on the wires. The wire
nuts should stay firmly in place, covering the bare ends.
4
YELLOW wire
(FAN)
GREEN wire
(GRD)
RED wire
(LIGHT)
Step 4
Fasten the W-81 wall control into the
wall box with the two switch box screws.
ÑÑCAUTION: Be certain that the wires are
not pinched!
Switch box
screws (2)
15
Twain
™
5
Fasten one of the two wall plates (white or ivory)
to the wall control using the two wall plate screws.
Step 5
6
Set the fan speed to HIGH on the wall control.
Return power to the panel and test the controller.
ÑÑCAUTION: Failure to set the fan speed to
HIGH can result in faulty operation of the
fan and damage to the wall control.
Wall plate
screws (2)
Operating the W-81 Wall Control
• Turn the upper knob to the desired fan speed.
• Turn the lower knob to the desired light setting.
Attaching the Canopy Hatch
7
Tuck the wires into the canopy with the wire nuts
pointed toward the ceiling. Place the BLACK and WHITE/
GREEN wires on opposite sides of the canopy. All wires
should be clear of the canopy opening. Tilt the motor
housing and downrod to install the canopy hatch.
sTEPs 7-8
Canopy hatch
8
Use the last remaining canopy screw and
lock washer to secure the canopy hatch. Straighten
the fan and ensure all parts are tightly secured.
Check for movement at the following joints:
Canopy screw
and washer
• Between the canopy and the ceiling
• Between the canopy and the
downrod and ball assembly
NO DRILL
16
Canopy
Twain
™
Installing the Blades
Hardware (not to scale)
Blades (5)
Blade Iron Plate
Screws (21)
Blade Iron Plates (5)
Blade Irons (5)
Blade Iron Screws (11)
Assembling
Step 1
1
Fan blade assembly
Place the blade iron plate on top of the blade
and the blade iron underneath the blade. Use a
manual screwdriver to secure the blade iron and plate
with the blade iron plate screws. Use four screws per
blade. Repeat this process for each fan blade.
NO DRILL
ÑÑCAUTION: Do not use an electric
screwdriver to assemble fan blades!
Step 2
Blade iron
Attaching
2
Install the assembled blades to the blade
holder ring using the blade iron screws. Use two
screws for each blade. Insert the end of the blade
holder into the slot on the blade holder ring.
Tighten the screws with a manual screwdriver.
Blade holder ring
Blade holder screws (2)
ÑÑCAUTION: Do not operate the fan at
this point. Installation must be completed
before turning on the fan.
Installed
blades
17
Twain
™
Installing the Light Fixture
Hardware (not to scale)
Light Adapter Plate (1)
Light Adapter Screws (3)
Light Fixture Screws (4)
Halogen Downlight Bulbs, 50W (2)
Glass Shade (1)
Finial (1)
Attaching the Light Fixture
Light Fixture (1)
Steps 2-3
1
Before getting started, remove the
rubberband from the plug connector.
2
Install two of the three light adapter screws into the
light adapter plate. Thread the plug connector through
the hole in the center of the light adapter plate.
3
Align the two key slot holes with the two screws and
rotate the light adapter plate clockwise. Install the third
light adapter screw and securely tighten all three screws.
4
Light adapter plate
Step 4
Connect the light fixture plug to the
plug from the bottom of the fan.
Light fixture
plug
18
Light adapter
screws (3)
Twain
™
5
Align the light fixture to the four posts on the
light adapter plate using the light fixture screws.
Step 5
Light fixture
Posts (4)
Light fixture
screws (4)
Attaching the Halogen Bulbs
NOTE: Do not remove the protective sleeve on
Step 6
the halogen bulb. Touching the glass casing of
the bulb may damage or break the glass.
6
Cut the sleeve to expose the connection end of
the bulb. Continue to hold the bulb by the sleeve during
installation. Screw both halogen bulbs into the light fixture.
ÑÑCAUTION: Only use maximum 50-watt
halogen bulbs!
NOTE: In compliance with US Federal Energy
Regulations, this ceiling fan contains a device
that restricts the light fixture to a maximum of
190 watts. Exceeding that limit or the marked
limit on this product may result in a fire hazard
or improper operation.
Halogen bulbs (2)
19
Twain
™
Attaching the Glass Shade
Step 7
7
Insert the threaded rod from the light assembly
through the hole in the center of the glass shade.
Threaded rod
Glass Shade
8
Finial
Step 8
Thread both pieces of the finial onto the
threaded rod. Screw the finial into place securely.
Installed fan
and light
fixture
20
Twain
™
Troubleshooting Tips
Care Recommendations
Please refer to this troubleshooting guide before
requesting service or contacting your dealer for assistance.
Fan Finishes
Problems and Possible Remedies
Fan will not start
• Check the main circuit fuses, circuit breakers, and wall
control position. Check all wire connections. Make
sure the power is turned off during this inspection.
Fan wobbles or shakes excessively
• Be sure the canopy pin is set properly into the slot on
the ball.
• The crossbar mounting bracket may be
attached too loosely. Make sure the hanger
bracket is attached tightly to the ceiling and
the downrod assembly is secured firmly.
• For cleaning, use a soft brush or lint-free
cloth to prevent scratching the finish.
• Surface smudges or an accumulation of dirt
and dust can be removed easily using a mild
detergent and slightly dampened soft cloth. An
antistatic agent may be used (on the fan base
and blades only), but never use abrasive cleaning
agents as these will damage the finish.
Blades
• Wood-finish blades should be cleaned with
a furniture polishing cloth. Occasionally, a
light coat of furniture polish may be applied
for added protection and beauty.
• The downrod may be attached to the downrod base
too loosely. Make sure all the screws are securely
tightened.
• For painted and high-gloss blades, surface
smudges or an accumulation of dirt and dust can
be removed easily using a mild detergent and
slightly dampened soft cloth. An antistatic agent
may be used, but never use abrasive cleaning
agents as these will damage the finish.
Fan is noisy during operation
No Need for Lubrication
• Tighten the canopy screws and mounting plate
assembly. Make sure the wire nuts inside the
canopy and switch housing are not touching
the metal parts and that they have not fallen
off the wire splices. Tighten as necessary.
• Never lubricate this fan! The precision motor
at the heart of your Casablanca fan features
sealed bearings that are lubricated for life.
• Tighten the blade irons to the flywheel (or Direct Drive
motor) and the blades to the blade iron screws.
Changing Lightbulbs
• Make sure all the screws in the motor housing are snug
but not overly tight.
Fan does not run on low speed
• If the fan is new, it may need to be “broken
in.” Run at high speed for several days.
• Do not attempt to oil the motor.
• Be sure to turn the power to OFF at the wall control
or circuit breaker before changing lightbulbs.
• Replace bulbs with the same type as you
removed from the light fixture.
• In compliance with US Federal Energy Regulations,
this ceiling fan contains a device that restricts the
light kit to a maximum of 190 watts. Exceeding
that limit or the marked limit on this product may
result in a fire hazard or improper operation.
21
Twain
™
22
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement