The World Models GM040 Sunrise EP Instruction Manual
Advertisement
Advertisement
I NST RUCT I ON M ANUAL
.
sunrise ep
Wing Span: 39.5 in / 1000 mm
Wing Area: 292 sq in / 18.8 sq dm
Flying Weight: 27 oz / 760 g
Fuselage Length: 40.5 in / 1030 mm
Requires: 4-channel radio w/ 4 micro servos. Outrunner
Motor KM0283010 w/ Propeller Adaptor HW2340100
20A Brushless ESC, 3 cells 11.1V 15C 1800 mAh Li-Po
battery & charger.
Warning ! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind of electric powered precision model. Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing. Always keep this instruction manual at hand for quick reference.
* Specifications are subject to change without notice.*
THE WINGS MAKER
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
.
GM040PO27791202
sunrise ep
INDEX
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
BEFORE YOU BEGIN
P.1
P.2
P.3-
P.9
P.9
1 Read through the manual before you begin, so you will have an overall idea of what to do.
2
Check all parts. If you find any defective or missing parts contact your local dealer. Please
DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.
Any parts you find to be defective after the gluing process may be difficult to remove for warranty replacement. The manufacturer will replace any defective parts, but will not extend to the parts that are good before gluing to defective parts during assembly. Warranty will not cover any parts modified by customer.
3
Symbols used throughout this instruction manual comprise of the following :-
Apply epoxy glue.
Apply instant glue
(C.A.glue, super glue.)
Must be purchased separately !
Apply thread locker
3mm
Assemble left and right sides the same way.
Peel off shaded portion covering film.
Drill holes with the specified diameter (here: 3mm).
Pay close attention here!
Ensure smooth non-binding movement while assembling.
Cut off shaded portion.
Pierce the shaded portion covering film.
Warning!
Do not overlook this symbol !
GM040PO27791202
P.1
Parts List
1.MAIN WING -- 1 pair
MICRO AILERON SERVO MOUNT PL5310020 -- 1 pair
STRAPER PL4112106 -- 2 pcs
CLEVIS PL4112105 -- 2 pcs
FUEL TUBE d2xD4x4mm -- 4 pcs
HORN PL4113103 -- 2 pcs
PUSHROD Ø1.4x65mm w/ Threads (For Aileron) -- 2 pcs
SCREW PA1.7x8mm -- 8 pcs
FIBRE TAPE 17x300mm -- 2 pcs
PLYWOOD 36.7x36.7x3mm -- 2 pcs
2.FUSELAGE -- 1 set
STABILIZER & ELEVATOR -- 1 set
FIBRE TAPE 17x380mm -- 1 pc.
3.VERTICAL FIN & RUDDER -- 1 set
FIBRE TAPE 17x175mm -- 1 pc.
PLYWOOD 36.7x36.7x3mm -- 1 pc.
4.TAIL LANDING GEAR PL3410030 --1 set
SCREW PA2x8mm -- 2 pcs
PLYWOOD 36.7x36.7x3mm -- 1 pc.
5.MAIN LANDING GEAR -- 1 set
MAIN WHEEL Ø40mm PL3116040 -- 2 pcs
WOODEN COLLAR Ø2.6mm -- 2 pcs
COLLAR Ø2.6mm w/ Set Screw -- 2 sets
SCREW PA2x8mm -- 1 pc.
SCREW PWA2x6mm -- 4 pc.
PLYWOOD 48x35.7x2.5mm (For Main Landing Gear) -- 1 pc.
MOUNTING PLATE 12x20mm -- 2 pcs
WHEEL PANTS -- 1 pair
LANDING GEAR COVERS -- 2 pcs
6.
MICRO AILERON SERVO MOUNT PL5310020 -- 1 pc.
SCREW PA1.7x8mm -- 4 pcs
FUEL TUBE d2xD4x4mm -- 2 pcs
CLEVIS PL4112105 --1 pc.
STRAPER PL4112106 -- 1 pc.
HORN PL4113103 -- 1 pc.
PUSHROD Ø1.4x135mm w/ Threads (For Elevator) -- 1 pc.
7.
MICRO AILERON SERVO MOUNT PL5310020 -- 1 pc.
SCREW PA1.7x8mm -- 4 pcs
FUEL TUBE d2xD4x4mm -- 2 pcs
CLEVIS PL4112105 --1 pc.
STRAPER PL4112106 -- 1 pc.
HORN PL4113103 -- 1 pc.
PUSHROD Ø1.4x130mm w/ Threads (For Rudder) -- 1 pc.
8.SOCKET HEAD SCREW M3x6mm -- 4 pcs
SCREW PM2x12mm -- 2 pcs
SCREW PA2.6x8mm -- 2 pcs
WASHER d3xD7mm -- 4 pcs
SPINNER Ø45mm SP27045BKO -- 1 pc.
10x6 FOLDING PROPELLER SET PL6314020 -- 1 set
9.WING TUBE Ø6x458mm -- 1 pc.
RUBBER BAND 4x30mm -- 2 pcs
10.COCKPIT -- 1 pc.
BATTERY TIE 200mm-- 1 pc.
SPONGE 10x50x150mm (For Radio Equipment & Battery) -- 2 pcs
DOUBLE-SIDED TAPE 30x35mm (For Brushless ESC) -- 1 pc.
11.DECALS: GM040 DEC -- 1 set
GM040PO27791202
P.2
1
Aileron Servo
PA1.7x8
mm
Screw
8
Bottom
Plywood
36.7x36.7x3mm
Fibre Tape
02L
03L
04L
02R
03R
04R
Servo(For Aileron)
Aileron Servo Lead
Bottom View
PA1.7x8mm
Bottom View
PA1.7x8mm
Straper
Bottom View
Clevis
Pushrod
Ø1.4x65mm
Horn
TWM PL8210010
CLEVIS WRENCH
Please choose either (02L&02R) or (03L&03R) or (04L&04R) that suits your servo.
GM040PO27791202
P.3
2
Stabilizer & Elevator
Bottom
Fibre Tape
Fibre Tape
17x380 mm
Bottom View
Vertical Fin & Rudder
Joining surfaces should be clean and dry. Slightly roughen surfaces with sandpaper for best results.
Fibre Tape
17x175 mm
Fibre Tape
Plywood
36.7x36.7x3 mm
Joining surfaces should be clean and dry. Slightly roughen surfaces with sandpaper for best results.
Tail Landing Gear
PA2x8mm
Screw
2
PA2x8mm
Wheel Ø23mm
GM040PO27791202
1.2mm
P.4
Plywood
36.7x36.7x3mm
Completed
Bottom View
5
Main Landing Gear
PA2x8mm
Screw
1
PWA2x6mm
Screw
4
2.6mm
Collar w/ Set Screw
2
10
0
Fuselage
Landing Gear
Plywood
48x35.7x2.5mm
Landing Gear
Bottom View
Completed
6
Elevator Pushrod
PA1.7x8
mm
Screw
4
PA2x8mm
Bottom View
Landing Gear Covers
Mounting Plate
12x20mm
PWA2x6mm
Wheel Pants
Landing Gear
2.6mm Collar
2.6mm Collar
Wheel Ø40mm
Bottom View
Bottom View
M3x3mm Set Screw
TWM PL8210010
CLEVIS WRENCH
02L
03L
04L
PA1.7x8mm
02R
03R
04R
Clevis
Pushrod
Ø1.4x135mm
Straper
Fuel Tube d2xD4x4mm
Horn
Bottom View
Please choose either (02L&02R) or (03L&03R) or (04L&04R) that suits your servo.
GM040PO27791202
P.5
7
Rudder Pushrod
PA1.7x8
mm
Screw
4
TWM PL8210010
CLEVIS WRENCH
Please choose either (02L&02R) or (03L&03R) or (04L&04R) that suits your servo.
02L
03L
04L
PA1.7x8mm
02R
03R
04R
Clevis
Pushrod
Ø1.4x130mm
Straper
Fuel Tube d2xD4x4mm
Horn
8
Outrunner Motor / Spinner
M3x6mm
Socket Head Screw
4
PM2x12mm
Screw
2
PA2.6x8mm
Screw
2
d3xD7mm
Washer
4
Optional Parts
Outrunner Motor 28/ 30
KM0283010
Propeller Adaptor
(d3xD5) HW2340100
EZ Connector
2
Brushless ESC
Make sure rotating motor casing is not in contact with wirings or anything.
1
M3x6mm d3xD7mm Washer
PM2x12mm
3
Folding Propeller
Set PL 6314020
ESC
Solder
Solder
Motor
TWM
KM0283010
4
PM2x12mm
Don’t over-tighten the PM2 screws, let the propeller blades align themselves when spinning.
5
PA2.6x8mm
GM040PO27791202
M5 Nut
TWM HW3111400
PROPELLER ADAPTOR WRENCH
P.6
Ø45mm
Completed
9
Main Wing
Rubber Band
Aileron Servo Lead
Wing Tube
Ø6x458mm
Completed
10
Radio Equipment
Outrunner Motor
Install and arrange the equipment as shown in the picture.
Battery
Receiver
Front
Battery Tie
Sponge
Brushless
ESC
Double Sided Tape
GM040PO27791202
Fuselage Bottom
P.7
Cockpit
Completed
11
Decals
Top View
Bottom View
12
Control Throws
Elevator
Rudder
Ailerons
GM040PO27791202
10mm
10mm
25mm
25mm
Adjust the control throws as shown in the diagram. These throws are good for general flying. You can adjust according to your personal preference.
12mm
12mm
P.8
13
C.G.
The ideal C.G. position is 95mm (3.75in.) behind the leading edge measured at where the wing meets the fuselage. In order to obtain the C.G. specified, add weight to the fuselage or move the battery position. Check the C.G. before flying.
95mm
3.75in
C.G.
http://www.thewingsmaker.com/instructionManuals.php
Warning!
Important Safety Precautions
# First time flyer should never fly by himself / herself. Assistance from experienced flyer
is absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
pre-adjusted aircraft.
sunrise ep
KM0283010 Outrunner Motor.
# Make sure the air field is spacious, never fly the plane too close to people and never get
too close to a running propeller. Extreme caution should be exercised when working with
electric powered models. Make sure the propeller is cleared of all objects, especially your hands before connecting the battery to the model. Make sure you understand the
operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you
plug in the battery for electric powered model, always treat the propeller as a rotating one,
as accidental movement of the throttle stick will spin the propeller and could cause injuries.
# Check and re-tighten up all factory assembled screws, use thread locker if necessary.
GM040PO27791202
P.9
Pl8210010
GM040PO27791202
Outrunner 28/ 32 Deluxe (25% higher power)
KM02832R1
-Kv(rpm/V): 1010
-Operating Power: 225W
-Operating Voltage: 6-15V
-Operating Current: 15A
-Peak Current: 20A(max.15 sec.)
-Internal Resistance: 102 m ohms
-Diameter: 28mm
-Length: 32mm
-Weight: 60g
-Shaft Diameter: 3mm
-Shaft Length: 15mm
-Mounting Screw:
M3(Front) and M2(Back)
-Distance of Mounting Holes:
16mm and 19mm(Front),
12mm(Back)
www.thewingsmaker.com
Pattern Flying Practice Guide
Wind Direction
1
2
4
9
5
6 x3 x3
13
10
14
16
17
12
3
11
15
7
GM040PO27791202
THE WINGS MAKER

Public link updated
The public link to your chat has been updated.
Advertisement