x Permasolid Elastic Additive 9050

x Permasolid Elastic Additive 9050
9050
14 V.1
Technical Data Sheet
Permasolid® Elastic Additive 9050
Permasolid Elastic Additive 9050 is a special additive of highly elastic polyurethane resins.
It is used for adjusting two-component top coats to the required degree of elasticity for painting plastic parts.
This product is for professional painting of vehicles only.
Technical Data Sheet No. 640.0. Mar. 2014
 2014 Axalta Coating Systems, LLC and all affiliates. All rights reserved.
9050
14 V.1
®
Elastifier for:
®
Permacron /Permasolid Clear Coats
®
®
Permacron /Permasolid 2K Surfacers (except VHS Surfacer 5150 and HS
Surfacer 5310)
Mixing ratio:
®
Add 15 - 30% Permasolid Elastic Additive 9050 to 2K Clear Coats, on all commonly
found types of plastics (not necessary on reinforced fiberglass).
®
Add 30% Permasolid Elastic Additive 9050 to 2K Surfacers (not for use in 5310 or
5150).
The base product must first be mixed with Permasolid Elastic Additive 9050. After which, in the case of 2K
products (not base coats), an appropriate hardener is added in the proper ratio.
Special Tips :
1. With two-stage finishes the base coat is applied without any Permasolid Elastic Additive 9050,
only the following clear coat is elasticized.
2. Do not pre mix with surfacers or clear coats. Add the hardener and apply the mixture immediately
after mixing with Permasolid Elastic Additive 9050.
3. To optimize the sanding properties, all elasticized 2K Surfacers should be dried 45 minutes at
140ºF.
4. Further instructions may be found in the System Data Sheet “The Paint System For Plastic Parts” (
TDS number 901.1)
5. Permacron Dura Plus 8580 may be added to improve dry time (Up to 10 %).
®
6. Adjust viscosity of 2K products with Permacron Reducer.
Mixing Ratios:
®
®
The mixing ratio with Permacron or Permasolid Hardeners is as follows:
®
2:1 in Permasolid Spectro Surfacer 5400
®
3:1 in Permasolid Vario Surfacer 8590
®
4:1 in Permasolid 2.1 Surfacer 5157
Storage conditions:
After use, replace lid immediately, ensuring an airtight seal.
 2014 Axalta Coating Systems, LLC and all affiliates. All rights reserved.
9050
14 V.1
Important Regulatory Information
Please see the appropriate VOC wall chart for compliance for your area. The values depicted below are
“ready to spray.”


For industrial use only by professional, trained painters. Not for sale to or use by the general
public. Before using, read and follow all label and MSDS precautions. If mixed with other
components, mixture will have hazards of all components. Ready to use paint materials
containing isocyanates can cause irritation of the respiratory organs and hypersensitive
reactions. Asthma sufferers, those with allergies and anyone with a history of respiratory
complaints must not be asked to work with products containing isocyanates. Do not sand,
flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with
particulate filters or appropriate ventilation, and gloves.
Any analytical results set forth herein do not constitute a warranty of specific product features or of the
product’s suitability for a specific purpose. All products are sold pursuant to our general conditions of
sale. We hereby disclaim all warranties and representations, express or implied, with respect to this
product, including any warranty of merchantability or fitness for a particular purpose. This product is
protected by patent law, trademark law, copyright law, international treaties and/or other applicable law.
All rights reserved. Unauthorized sale, manufacturing or use may result in civil and criminal penalties.
SPIES HECKER, INC.
47818 West Anchor Court
Plymouth, MI 48170
Tel. 800-447-7437 (800-44-SPIES)
Fax 734-354-3405
www.SpiesHeckerUSA.com
 2014 Axalta Coating Systems, LLC and all affiliates. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement