Salamander Designs IR ALL IN ONE IR Hub Repeater User guide

Below you will find brief information for IR Hub Repeater IR ALL IN ONE. Salamander Designs IR ALL IN ONE is a complete solution for controlling your home theater or A/V system. With the included IR receiver, emitters, and mounting hardware, you can easily install this system in your cabinet and control your components with your existing remote. The system includes a 36ft range for your IR signal output, a power supply with adapter, and a wire manager for organizing wires.

PDF Download

Document

IR ALL IN ONE includes these items:
1. Mounting IR Hub
Furniture Shaped By Your Needs
SalamanderDesigns.com
Mounting to Salamander
Furniture with Aluminum Frame
1 - Hex Key
#400-080
2 - Button Head Screws
#300-518
Use two Drop-In Nuts with two
Button Head Screws to mount Hub
on the inside or backside of cabinet
attaching to aluminum post.
1 - Power Supply
#056-007 (USA)
#400-245 (EU,UK)
2 - Drop-in Nuts
#300-565
Slip nut into slot and tighten the
button head screw to lock the nut
into place.
2 - Wood Screws
#300-115
Note: Nut must slant from top left
to bottom right as shown below.
2 - IR Emitters
#400-205
IR Receiver
36’’
Mounting to Wood Cabinets
Use supplied wood screws to mount
Hub to interior or exterior of cabinet.
users guide
4 - IR Emitter Holsters
#440-297
1 - IR Receiver Holster
#440-296
LED Status Indicators:
Power and IR Data
Doc #500-160 v04.15
2. Attach IR Receiver
Attach Receiver Holster to front
of cabinet and place the IR Receiver
in holster.
3. Attach Emitters
IR Emitter outputs
Note: If the IR repeater does not seem to work properly, see back for troubleshooting guide.
Emitter Holster
Features
all in on e
• IR remote is compatible with any A/V component that has the All-In-One Solution
by Salamander Designs.
• The plasma proof remote head IR receiver uses advances optical and electronic
filtering for interference rejection.
• LED lights provide power and IR signal status.
Emitter
Receiver
Wire Manager
DC Adapter
DC Power Input
Attach IR Emitter Holsters in front
of IR sensors of each component
and place the IR Emitter in holster.
Note: IR Receiver should be
placed within sight.
Receiver Holster
6 - Wire Managers
#440-322
• A 2-piece design makes it easy to conceal and simple to install.
Specifications
Note: Be sure the Emitter is
securely attached directly over the
component’s IR receptor. To locate
the IR receptor, shine a flashlight at
the unit and look for the sensor.
Specifications:
Power Supply:
IR Freq. Range Supported:
IR Pickup Range:
IR Receiver Head Dimensions:
IR Emitter Outputs:
(Typical)
USA:
In: 110V - 120V
EU, UK: In: 120V - 240V, 50 - 60Hz
Out: 8 - 12V
36 kHz - 60 kHz
40 ft. @ 38kHz, 20 ft. @ 56kHz
0.65’’ x 0.35’’ x 0.25’’
4* (expandable to 6)
Specifications subject to change without notice.
Limited Warranty
Salamander Designs will repair or replace any defect in material or workmanship
which occurs during normal use of this product with new or rebuilt parts, free of
charge in the USA, for two years from the date of original purchase. This is a no
hassle warranty with no mail in warranty card needed. This warranty does not cover
damages in shipment, failures caused by other products not supplied by
Salamander Designs, or failures due to accident, misuse, abuse, or alteration of the
equipment. This warranty is extended only to the original purchaser, and a
purchase receipt, invoice, or other proof of original purchase date will be required
before warranty repairs are provided.
Mail in service can be obtained during the warranty period by calling toll-free (800)
535-5659. A Return Authorization number must be obtained in advance and can be
marked on the outside of the shipping carton.
This warranty gives you specific legal rights and you may have other rights (which
vary from state to state). If a problem with this product develops during or after the
warranty period, please contact Salamander Designs, your dealer or any
factory-authorized service center.
Troubleshooting
1) Check Power - make sure sure the red LED light is on,
indicating power to the hub.
3) Check IR Emitter - be sure Emitter it is placed directly over
IR receiver on electronic component.
If not working ...
4) Some new electronic components utilize a unique IR code sensitivity.
You will need to match the sensitivity of the repeater to match the
electronic component. To adjust the sensitivity of the repeater turn
the adjustment screw. Begin by turning the adjustment screw all the
way to the left, counter clock-wise. Test the remote control through
the repeater to verify that it is functioning. If the remote does not
function properly, turn the adjustment screw in small, 1/8 turn
increments and test again. Once the unit becomes responsive
verify all commands are received.
The component that
2) Test IR Receiver - make sure IR receiver is in direct
requires adjustment
line-of-sight contact with your remote. Point remote
should be plugged
at IR receiver to confirm IR signal is received.
into this port.
Confirm green light.
Still not working?
Customer technical assistance is available at 1-800-840-0288
">

Hello! I am an AI chatbot specifically trained to assist you with the Salamander Designs IR ALL IN ONE IR Hub Repeater User guide. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Hide related prompts

Assistant typing

Assistant terminated

Key Features

36ft IR signal range
IR receiver and emitters included
Easy to install
Compatible with most A/V components
Advanced optical filtering for interference rejection
LED lights for power and IR signal status
2-piece design for easy concealment
Wire manager for organizers
Two year warranty

Frequently Answers and Questions

How do I mount the IR Hub?

You can mount the IR Hub to Salamander furniture with an aluminum frame using the included hex key, button head screws, drop-in nuts, and wood screws. You can also mount the IR Hub to wood cabinets using the included wood screws.

How do I attach the IR receiver?

Attach the IR receiver holster to the front of the cabinet and place the IR receiver in the holster. Make sure that the IR receiver is in direct line of sight contact with your remote and that the green LED light is on.

How do I attach the IR emitters?

Attach the IR emitter holsters in front of the IR sensors of each component and place the IR emitter in the holster. Make sure that the emitter is securely attached directly over the component's IR receptor.

What do the LED status indicators mean?

The red LED light indicates power to the hub. The green LED light indicates that the IR signal is being received.

What do I do if the IR repeater does not seem to work properly?

Check the power, the IR emitter, the IR receiver, and the sensitivity of the repeater. If none of these solutions work, contact customer technical assistance at 1-800-840-0288.