R Factory Reset Procedures
®
R
Factory Reset Procedures
Caution: Many of these procedures will erase all memory in the unit. Make sure you have
backed up any data you wish to keep before performing these procedures! If a unit is not listed
here, it does not have an initialization procedure that is user-executable.
A
Model
A-30/33/37
A-50/80
A-70/90/90EX
A-220
A-300PRO
A-500PRO
A-500S
A-800PRO
A-880
AD-8
AP-700
AT-Series
AX-09
AX-1/7
AXIS-1
AX-Synth
B
Model
BR-8/532/1180
BR-600
BR-800
BR-864
BR-900CD/
1200CD
BR-1600CD
C
Model
CD-2
CD-2E/2i
CDX-1
CE-20
CR-80
D
Model
D-2
DB-30
DB-60
DB-88
DB-90
DD-20
Procedure
Power on while holding WRITE. (Hold for 15 seconds)
While holding the first, third, and fourth buttons under the display, press CHANNEL. Then
press any cursor button
Power on while holding down MANUAL, then press ENTER
Power on while holding B and MEMORY
Hold ACT and <, use the VALUE dial to select “FACTORY RESET.” Press ENTER twice.
Hold ACT and <, use the VALUE dial to select “FACTORY RESET.” Press ENTER twice.
Hold MIDI CH and PGM CHANGE, press the SYSTEM key, Use the VALUE dial to select
“SY6,” press ENTER 3 times.
Hold ACT and <, use the VALUE dial to select “FACTORY RESET.” Press ENTER twice.
Power on while holding SIGNAL and MEMORY
Power on while holding WRITE. Confirm that “F” flashes in the display, then release
WRITE. Press WRITE again
Power on, then press EXIT repeatedly to get ANALYZER/FILTER screen. Cursor to MENU,
press ENTER. Cursor to SYSTEM, press ENTER. Cursor to INITIALIZE, press ENTER. Use
VALUE to select ALL MEMORY, then press ENTER twice
(Make sure disk drive is empty.) Power on while holding ONE TOUCH PROGRAM
Power on while holding FAVORITE A, B, and WRITE. Press TONE 5, then press WRITE.
Power on while holding WRITE. (Hold for 30 seconds)
While holding FUNCTION, press the F#0, C#2, and D#2 keys
Power on while holding INC/+, DEC/-, and TONE 7(ORGAN/CLAVI), then press WRITE.
Procedure
Press UTILITY. Cursor to “Initialize.” Press ENTER. Cursor to “All.” Press ENTER twice
Power on while holding GUITAR, MIC, and LINE. Press ENTER.
Press MENU. Cursor to “Factory Reset.” Press ENTER three times.
Power on while holding INPUT SELECT/GUITAR/BASS, MIC, and LINE. Press ENTER
Press UTILITY. Press CURSOR Right to select “Initialize.” Press ENTER. Press CURSOR
Right to select “All.” Press ENTER twice
Press UTILITY. Cursor to “Initialize.” Press ENTER. Cursor to “All.” Press ENTER twice
Procedure
Press MENU. Use the DATA dial to select “INITIALIZE.” Press ENTER twice.
Press MENU. Use the < / > buttons to select “Factory Reset.” Press ENTER twice.
Press UTILITY. Cursor right to “INIT”. Press ENTER/YES. Use CURSOR buttons to select
desired target to be initilaized, (GLOBAL, FX, MIXER, ALL). Press ENTER/YES twice
Power on while holding WRITE. Release WRITE then press WRITE again
Power on while holding DEL and REPEAT, then press ENTER
Procedure
With the unit on, Hold WRITE and press SYSTEM. Press ENTER twice
Power on while holding the START/STOP button until “F” shows in the display
Power on while holding the MEMORY button until “F” shows in the display
Power on while holding METRONOME MODE and LOOP MODE. Press WRITE
Power on while holding MEMORY
Power on while holding WRITE. Release, then press WRITE again
©2010 Roland Corporation U.S.
Page 1
®
R
DDR-30
DEP-3/5
DJ-70/70MKII
DR-3
DR-5
DR-202
DR-550/550MKII
DR-660
DR-670
DR-770
DR-880
DS-330
E
Model
E-09
E-10/20/30
E-35
E-36
E-50/60/80
E-56
E-66
E-68/70/86/96
E-300/500
E-600
EG-101
EM-10
EM-15/25
EM-20/30/50/55
EM-2000
ep-5/7/7MKII
ep-9
ep-75/85
EQ-20
EXR-3/5
EXR-40/46OR
F
Model
F-110
Fantom
Fantom-G6/7/8
Factory Reset Procedures
Power on while holding the #1 button
Power on while holding MEMORY NO UP (^) and DOWN (v)
Power on while holding the UP ARROW button to enter test mode. Press A, press C, press
S1. When finished the screen will display IC21 = OK
Press EDIT. CURSOR Right to select “SYSTEM.” Press ENTER. CURSOR Right to select
<FACTORY RESET>. Press ENTER twice
Power on while holding FRET LEFT (<) and RIGHT (>), then press ENTER twice
Power on while holding MUTE and ROLL. Press TAP/ENTER. Cursor to “YES” in the
display. Press TAP/ENTER
Power on while holding -1 and +1, then press START
Press UTILITY, then use LEFT (<) and RIGHT (>) to select [8] INIT. Press ENTER twice
Power on while holding REC and STOP / CONT. Press ENTER twice
Press UTILITY, then use LEFT (<) and RIGHT (>) to select [9] F. RST. Press ENTER twice
Press EDIT. Press CURSOR Right to select “Factory Reset.” Press ENTER twice
Power on while holding REVERB and SPLIT, then press YES
Procedure
Press FUNCTION so it is lit. Use the FAMILY </> buttons to select “Utility,” then use the
SELECT </> buttons to select “Factory Reset.” Press TEMPO >/YES twice
Power on while holding WRITE
Power on while holding REC/PUNCH IN
Power on while holding RECORDER
Press MENU. Press “UTILITY” then press “FACTORY RESET.” Press “EXECUTE.”
Power on while holding WRITE
Power on while holding REC in the DISK RECORDER section
Power on while holding WRITE
Press UTILITY. Use the buttons under the display that correspond to <<PAGE>> to
select FACTORY PRESET. Press EXECUTE, then press OK. When the screen displays
RESET COMPLETE, turn the unit off, then on
Press FUNCTION and use the PAGE (<) (>) buttons to select “Factory Preset.” Touch the
“Execute” icon followed by the “OK” icon on the display screen. Power off then on
Power on while holding WRITE
Power on while holding USER PROGRAM/WRITE
With the unit on, press FUNCTION until “RESUME” shows in the display. Then press
TEMPO+
Power on while holding USER PROGRAM/WRITE
Performance Sets need to be loaded from disk to restore factory default settings. Insert
the factory ZIP Disk into the drive and power on. Press F5 (Disk), then F1 (Load). Press
PAGE ^ / v to select “PRF MEM” and press UPPER 1(Execute)
While holding REC and PLAY, press STRINGS. Power off and then back on
While holding REC and PLAY, press CHOIR. Power off and then back on
Power on while holding REC
Power on holding LIGHT and SELECT. Release, then press LIGHT and SELECT again
Power on while holding USER PROGRAM/WRITE
Power on while holding USER PROGRAM/WRITE
Procedure
Hold REVERB and press TRANSPOSE, hold OTHERS and use the +/- buttons to select
“Fct” in the display. Press the Stop/Start button twice.
With the unit on, press MENU. Press the UP or DOWN cursor buttons to select FACTORY
RESET. Press 8 (EXECUTE) twice
Press MENU. Use the CURSOR Up and Down buttons to select “Factory Reset,” then press
F8 [Select] followed by F7 [OK]. Press F7 [OK] when completed.
©2010 Roland Corporation U.S.
Page 2
®
R
Fantom-S/S88
Fantom-Xa
Fantom-XR
Fantom-X6/7/8
FC-100MKII
FC-200
FG-10/1000
FP-2
FP-4
FP-5
FP-7
FP-8
FR-3
FR-5/7
Factory Reset Procedures
Press MENU. Use the CURSOR Up or Down buttons to select “Utility,” then press ENTER.
Press 3 (Factory Reset) Press 8 (Execute)
Press EXIT. Press MENU. Turn the VALUE dial to select “Utility” and then press ENTER.
Press F3. Press F6
Press MENU. Press CURSOR Down to select “UTILITY.” Press ENTER. Press CURSOR
Down to select “FACTORY RESET.” Press ENTER twice
Press MENU. Press the CURSOR DOWN button to select “Utility.” Press button 3 (Factory
Reset). Press Button 8 (Exec). Cycle the power
Power on while holding pedals #1, #2, and #8
Power on while holding the #10 pedal, then press the CTL pedal
Power on while holding CLEAR and EXIT
Power on while holding REVERB until “Fct” shows in the display
Power on while holding FUNCTION
Power on while holding PEDAL CONTROL
Power on while holding FUNCTION
Press FUNC and release. While holding PIANO, press FUNC again
Power on while holding SET and ORCHESTRA.
Power on while holding MENU/WRITE. Press the DATA/ENTER button
G
Model
G-70
G-600/800
G-1000
GI-10
GI-20
GM-70
GP-16
GP-20
GP-100
GR-09
GR-1
GR-20
GR-30
GR-33
GS-10
GT-3
GT-5
GT-6/8/Pro
GT-6B
GT-10/10B
GW-7
GW-8
GX-700
Procedure
Press MENU. Touch UTILITY, then touch FACTORY RESET. Touch EXECUTE
Power on while holding WRITE
Performance Sets need to be loaded from disk to restore factory default settings. Insert
the factory ZIP Disk into the drive and power on. Press F5 (Disk), then F1 (Load). Press
PAGE ^ / v to select “PRF MEM” and press UPPER 1 (Execute)
Power on while holding PARAMETER + and -, then press VALUE +
With the power off, set the GUITAR /BASS switch to match the instrument you are using.
Power on while holding TUNER(STRING SEL). Press WRITE
Poly Mode: Power on while holding PLAY, GENERAL EDIT, and IND EDIT.
Mono Mode: Power on while holding TUNE, CONTROL ASSIGN, and DATA TRANSFER
Power on while holding the #6, #7, and #8 buttons. Use the FUNCTION LEFT (<) and
RIGHT (>) buttons to select “2.All Factory Preset,” then press WRITE three times
Power on while holding WRITE. Release WRITE, (The MEMORY indicator will flash), then
press WRITE again
Power on while pressing in the PARAMETER knob, then press WRITE
Power on while holding Pedal #2, then press the VALUE + button. Now press EDIT/PLAY
Power on while holding WRITE/COPY, then press YES
Power on while holding WRITE, then press WRITE again
Power on while holding Pedal #2, then press the PATCH+ button to select INI. Press
EDIT/PLAY. Then press PATCH+ and PATCH- simultaneously
Press SYSTEM. Press PARAMETER (>) right to select “FACTORY RESET”. Use VALUE to
select “ALL”. Press WRITE twice
Power on while holding the CHANNEL SELECT A and B buttons (within the
PREAMP/SPEAKER section), then press WRITE
Power on while holding MOD and SFX. Press WRITE
Power on while holding MOD and FEEDBACKER/SLOW GEAR. Press WRITE
Power on while holding the PREAMP ON/OFF and (PREAMP)TYPE/VARIATION buttons.
Press WRITE
Power on while holding COMP/LIMITER ON/OFF and TYPE VARIATION. Press WRITE
Press SYSTEM. CURSOR right to select “FACTORY RESET” then press ENTER twice.
Press FUNCTION. Press SELECT Left or Right to choose “Utility.” Press ENTER twice
Press MENU. Use the CURSOR Up and Down buttons to select “Utility” then press ENTER.
Use the CURSOR buttons to select “Factory Reset” then press ENTER twice. Power off and
on.
Press TUNER/UTILITY. Use PARAMETER LEFT (<) and RIGHT (>) buttons to select FACT
©2010 Roland Corporation U.S.
Page 3
®
R
Factory Reset Procedures
INIT. Cursor to left and dial SYSTEM, then right and dial P#100. Press WRITE, then
TUNER/UTILITY
H
Model
HP-130
HP-557
HPD-10
HPD-15
Procedure
Power on while holding REC
Press GUIDE button until it is NOT lit. Touch PIANO, then touch FUNCTION. Use Page (<)
(>) to select the function page. Touch FACTORY RESET. Touch OK
While holding SHIFT, press EDIT. Press the V button until you see “FACTORY RESET.”
Press >, then use the +/- buttons to select “ALL.” Press V, then press 4/OK
Press SYSTEM and use the PARAMETER (>) to select “FACTORY RESET SYSTEM.” Use
the VALUE dial to select “ALL” and press WRITE
J
Model
JD-800
JD-990
JP-8000
JP-8080
JS-30
JS-5
Juno-D
Juno-Di
Juno-G
Juno-Gi
Juno-Stage
JV-30
JV-35/50
JV-80/90
JV-880
JV-1000
JV-1010
JV-1080
JV-2080
JW-50
JX-1
JX-305
K
Model
KF-90
KR-5/7
Procedure
Press DATA TRANSFER. Use PAGE UP (^) and DOWN (v) to select FACTORY PRESET.
Press YES
While holding EXIT, press UTILITY. Press F6 (EXECUTE), then F5 (YES)
While holding SHIFT, press INIT/UTIL. Press INIT/UTIL repeatedly to select INITIALIZE
WRITE. Use the DOWN/UP buttons to select FACTORY PRESET, then press WRITE
Press EDIT. Press INIT/UTIL (Bank 7) repeatedly to select Factory Reset. Press REC then
press WRITE
Power on while holding RECORD located in the SEQUENCER section
Press UTILITY. Use CURSOR buttons to select “16 SYSTEM FACTORY RESET.” Press
ENTER twice
Press MENU. Press PAGE/CURSOR Right to select “Factory Reset”. Press ENTER twice
Press MENU. Use ^/v to select “UTILITY” then press ENTER. ^/v to select “FACTORY
RESET” then press ENTER twice.
Press MENU. Use ^/v to select UTILITY then press ENTER. Press F3 FACTORY then press
F6 EXECUTE.
Press MENU. Use the VALUE Dial to select “5. Utility” then press ENTER. Use the VALUE
Dial to select “Factory Reset” then press ENTER. Press Button 5 [EXEC].
Press MENU. Use the CURSOR buttons to select “UTILITY,” then press ENTER. Use the
CURSOR buttons to select “FACTORY RESET,” then press ENTER. Press 7 [EXEC] to
confirm. Power off then back on when finished.
Press CHORUS and REVERB (above INITIALIZE) simultaneously. Press VALUE UP (^)
Press CONTROL and MASTER simultaneously. Use PARAMETER UP (^) and DOWN (v) to
select ALL. Press VALUE UP (^)
Power on while holding NUMBER 8 (also labeled PERFORM 16 and CAPS). Press ENTER
and then press WRITE
Press UTILITY, then use the DATA dial to select FACTORY PRESET. Press ENTER twice
Power on while holding NUMBER 8 (also labeled PERFORM 16 and CAPS). Press ENTER,
then press WRITE
Press VALUE to select Performance Mode. While holding VOLUME press VALUE. Use the
CATEGORY/BANK dial to select Piano (LCD will display Fct). Press VALUE twice
Press UTILITY. Cursor down once, then cursor right three times to select FACTORY
PRESET. Press ENTER twice, then press UTILITY
Press UTILITY. Press F6 twice to select MENU 3. Press F1. Then press F6. If necessary,
use the VALUE DIAL to turn Memory Protect OFF and press F6 twice
Press TUNE/FUNCTION. Press F5 (FACTORY), then F4 (JW RESET), then F3 (GS RESET),
then F4 (YES)
Power on while holding WRITE and FLUTE
Press UTILITY. Use PAGE </> to select Factory Preset and press ENTER. Use PAGE </>
to select ALL and press ENTER twice
Procedure
Press FUNCTION. Touch [System Setting]. Touch [Facotry Reset]. Touch [Execute
Press the One Touch Program PIANO button. Touch FUNCTIONS. Touch FACTORY RESET
©2010 Roland Corporation U.S.
Page 4
®
R
KR-15/15M
KR-55
KR-75
KR-177
KR-277/375
KR-350
KR-377
KR-500
KR-570
KR-575
KR-577/977
KR-650
KR-770
KR-1070
KR-1077
KR-3000
KR-3500/4500
KR-4700/5000
KR-5500
L
Model
LVC-1N
M
Model
M-10/16DX
M-660/760
M-1000
M-BD1/DC1
M-GS64/OC1
M-SE1/VS1
MC-09
MC-303
MC-307
MC-505
MC-808
MC-909
Factory Reset Procedures
Press the One Touch PIANO button. Touch FUNCTION SETTINGS. Touch FACTORY
RESET. Touch EXECUTE. Touch YES
Hold MIDI/FUNC and press CARD. Hold both VARIATION buttons for 5 seconds
Press UTILITY and use the PAGE <</>> buttons to select “Factory Preset.” Press
EXECUTE, then press OK
In the Utility menu screen, press PAGE < (left) or PAGE >(right) to select the “FACTORY
PRESET” page. Press EXECUTE. Press OK
Press FUNCTION until it is lit. Use BEAT and TEMPO buttons to display “FNC41”. Press
TRANSPOSE twice
While holding LOAD and SAVE, press WRITE
Press FUNCTION until it is lit. Use the PAGE left or PAGE right buttons at the bottom of
the display until “Factory Reset” appears. Press “FACTORY RESET” next to the display.
Press EXECUTE at the bottom of the display. Press OK
While holding FROM and TO, press WRITE
While holding PART VOLUME ACCOMP, press TRACK 2 and 4 buttons (Composer section)
simultaneously. Press PART VOLUME ACCOMP repeatedly to get FACTORY SETUP LOAD in
the window. After loading is complete, power off and then back on
Press FUNCTION and use the PAGE left or right buttons to select “Factory Preset.” Touch
the “Execute” icon followed by the “OK” icon on the display screen. Power off then on
Press FUNCTION until it is lit. Touch [Factory Reset]. Touch [Execute]. Touch [OK]
While holding LOAD and SAVE, press WRITE
While holding PART VOLUME ACCOMP, press TRACK 2 and 4 buttons (Composer section)
simultaneously. Press PART VOLUME ACCOMP repeatedly to get FACTORY SETUP LOAD in
the window. After loading is complete, power off and then back on
Press UTILITY and use the PAGE <</>> buttons to select “Factory Preset.” Press
EXECUTE, then press OK
Press FUNCTION until it is lit. Touch [Factory Reset]. Touch [Execute]. Touch [OK]
While holding FROM and TO, press WRITE
While holding LOAD and SAVE, press WRITE
While holding EDIT, press LOAD and SAVE
While holding LOAD and SAVE, press WRITE
Procedure
Power on while holding ENTER
Procedure
Power on while holding FINALIZE and ROOM ACOUSTIC
While holding EDIT, press WRITE. Use PARAMETER UP (^) and DOWN (v) to select ALL,
then press WRITE. When completed, press EDIT to return to Play Mode
Set the SELECT switch to the OPTICAL Input setting, then power on while holding the
CLOCK SOURCE button
Power on while holding F3
Power on while holding F3
Power on while holding F3
Press SETUP. Press INC or DEC until “Fct” shows in the display. Press ENTER, then press
WRITE
Power on while holding down SHIFT, then press ENTER
With unit on, Press SYSTEM. Press F2 UTIL. Press CURSOR DOWN until “Factory Reset”
appears. Press F1. Press F4
Power on while holding down SHIFT, then press ENTER. Note, this procedure takes
several minutes
Press SYSTEM, then hold SHIFT and press keyboard pad 16. CURSOR to “Factory Rest”
and press ENTER twice.
With the unit on, press MENU. Use CURSOR to select “Utility.” Press ENTER. Press F4
(Factory Reset.) Press F6 (Execute)
©2010 Roland Corporation U.S.
Page 5
®
R
ME-5
ME-6/6B
ME-8/8B
ME-10
ME-20/20B
ME-25
ME-30
ME-33
ME-50/50B
ME-70
ME-X
MICRO BR
MK-80
MKS-50
MMP-2
MT-32
MT-90S
MT-100
MT-120/120S
MT-200
MT-300S
MV-8000/8800
Factory Reset Procedures
Power on while holding pedals #1 and #2, then press WRITE immediately
Power on while holding PARAMETER DOWN (v) and LEFT (<), then press WRITE
Power on while holding PARAMETER LEFT (<) and DOWN (v), then press WRITE/COPY
Power on while holding the BANK DOWN (v) pedal, then press WRITE
In Manual Mode, hold EDIT/EXIT and press PEDAL 2. Press WRITE twice.
Hold EXIT and press the MEMORY v (down) pedal. Press WRITE twice.
Power on while holding PARAMETER RIGHT (>) and VALUE DOWN (-), then press
WRITE/COPY
Power on while holding the AMP/EFFECT right button and EZ TONE. Release, then press
WRITE and wait for “WRITE” to stop flashing in the LCD. Power off, then on again
Power on while holding WRITE and BANK Left <, then Press WRITE Twice
Press Pedals 3 & 4 at the same time to switch to Manual Mode. Hold down EDIT / EXIT
and press the MOD pedal. Press WRITE twice.
Power on while holding PARAMETER DOWN (v) and LEFT (<), then press WRITE
Power on while holding UTILITY. Press YES twice.
While holding WRITE, press EDIT. While holding the LEFT (<) and RIGHT (>) cursor
buttons, press UP (^)
Poly Mode: Power on while holding NUMBER 4 and 8.
Mono Mode: Power on while holding NUMBER 3 and 7
With the unit on press SYSTEM until it is orange. Press PAGE until “INITIALIZE” appears.
Use the left VALUE control to select the desired target to be initialized. (SYSTEM, USER
PATCHES, ALL). Press ENTER twice
While holding MASTER VOLUME, press RHYTHM PART. Press PART 1
With the unit on, Press SONG and [4]. Press <(Bwd) or >(Fwd) until “Factory Reset” is
displayed. Press (+). Press > (PLAY). Turn off the power, then on again
While holding STOP, press DELETE. After the display flashes ALL CLEAR, press EXECUTE
Power on while holding REPEAT, SONG (blue button), and PLAY. Press FWD repeatedly,
until the window reads T-13. Press PLAY, then press REC. Power off, then on
Power on while holding REPEAT, SONG (blue button), and PLAY. Use the DIAL to select
T-15 in the window. Press PLAY, then press REC. Power off, then on
Press MENU and use the VALUE DIAL to select “13:Factory Prset”. Press
ENTER/TRANSPOSE twice. Power off then on
Press SYSTEM, press F5 (SysInfo), press F3 (Initialize), press F5 (Yes). Please note that
all factory patches need to be reinstalled via CD-ROM.
P
Model
P-55
Pad-8
Pad-80
PC-150
PC-200/200MKII
PCR-30/50/80
PCR-M30/50/80
PCR-300/500/800
PK-5
PM-16
PMA-5
Prelude
Pro-E
PW-10
Procedure
Power on while holding both INSTRUMENT buttons, then press PARAM 1
Power on while holding MIDI CH and NOTE NUMBER. Power off, then back on
Power on while holding both VALUE (solid < and >) buttons
Power on while holding COMMAND on the left edge of the keyboard
Power on while holding the two buttons under the word STANDARD
Press EDIT. Press the SYSTEM key, then press the # 8 key. “SY8” will show in the
display. Press ENTER three times
Press EDIT. Press the SYSTEM key, then press the # 8 key. “SY8” will show in the
display. Press ENTER three times
Press EDIT. Use the VALUE knob to select “SYS,” then press ENTER. Use the VALUE knob
to select “SY16,” then press ENTER. Press ENTER twice.
Power on while holding OCT/PARAM
Power on while holding NUMBER buttons 1 and 2. (This reloads the first BANK of settings)
Press UTILITY, then press the RIGHT (>) cursor button repeatedly to select INITIALIZE.
Press ENTER, then [EXEC]
Press MENU. Use the ^/v buttons to select “Utility” then press ENTER. Use the Cursor
buttons to select “Factory Reset” then press ENTER.
Power on while holding WRITE
With the unit off, turn the TYPE knob to “VO-WAH”. Power on while holding
©2010 Roland Corporation U.S.
Page 6
®
R
Factory Reset Procedures
MANUAL/MEMORY. (ON/OFF will blink three times, then the MEMORY indicator blinks).
Release MANUAL/MEMORY, then press MANUAL/MEMORY again
R
Model
R-09/HR
R-5/8/8MKII
R-8M
R-70
RA-50/90
RA-95
RA-800
RC-50
RD-150
RD-170
RD-300GX
RD-300SX
RD-500
RD-600
RD-700/GX/SX
RM-2
RMP-3/5
RS-5/9
RS-50/70
RSP-550
RSS-10
RV-70
Procedure
Press MENU. Use the ^/v buttons to select “FACTORY RESET.” Press REC twice.
Power on while holding CURSOR PAGE and PARAM SELECT, then press ENTER twice
Power on while holding ENTER and the RIGHT (>) CURSOR button, then press ENTER twice
Power on while holding MIDI and ASSIGN, then press YES twice
Power on while holding WRITE
Power on while holding REC
(WARNING: This will erase the original factory Performance settings. However, you can
save them to disk before doing this procedure.) Power on while holding WRITE
Power on while holding PLAY MODE and LOOP SYNC. Press ENTER.
Power on while holding REC and PLAY
Power on while holding WRITE
Press EDIT. Use INC/DEC to select “Utility,’ then press ENTER. Use INC/DEC to select
“Factory Reset,” then press ENTER twice.
Press EDIT. Use INC/DEC to select “UtL,” then press ORGAN. Press ENTER twice.
Power on while holding NUMBER 1 and 8. Press DEC/YES
Press EDIT. Press the RIGHT PAGE button until “Initialize All” is displayed. Press
INC/YES twice. Press EDIT to return to Play mode
Press EDIT. CURSOR down to “9 UTILITY” and press ENTER. CURSOR down to “Factory
Reset All” and press ENTER three times
Power on while holding VALUE UP, SELECT and METRONOME. When “rSt” flashes in the
display, press METRONOME again
Power on while holding STOP/START. Press and hold STOP/START until reset is
completed.
With the unit on, press UTILITY. Use VALUE + / - to select “Factory Reset”. Press ENTER.
Use VALUE + / - to select “All”. Press ENTER twice
Press PATCH so it is lit. Press UTILITY so it is lit. Use PAGE/CURSOR Left or Right to
select “Ag5: FACTORY RESET.” Press ENTER twice
Power on while holding PROGRAM/PAGE UP (^) and DOWN (v), then press WRITE
Power on while holding LOCK and OPTION. (The MCR-8 LED lights.) Press DEMO
PROGRAM four times. Press DEVICE ID
Power on while holding WRITE and DOWN. Use the UP (^) and DOWN (v) buttons to
select AL. Press WRITE. Power off, then back on
S
Model
SB-55
SC-33
SC-50/55/MKII
SC-88
SC-155
SC-880
SD-35
SDE-330
SDX-330
SE-50
SE-70
SH-01
Procedure
Power on while holding CLEAR
Power on while holding REVERB and SPLIT, then press YES
Power on while holding both INSTRUMENT buttons, then press ALL
While holding SELECT, press both INSTRUMENT buttons. Press ALL
Power on while holding both INSTRUMENT buttons, then press ALL
Press UTILITY. CURSOR UP and use the VALUE DIAL to select Factory Preset. CURSOR
DOWN and use the VALUE DIAL to select ALL. Press ENTER twice
Power on while holding CLEAR, then press REC
Power on while holding SYSTEM and PROGRAM. Use the DATA dial to select SYSTEM +
PROGRAM. Press MEMORY
Power on while holding SYSTEM and PROGRAM. Use the DATA dial to select SYSTEM +
PROGRAM. Press MEMORY
Power on while holding PARAM UP (^) and VALUE UP (^). Press WRITE. Wait three
seconds and press WRITE again
Power on while holding in the NUMBER/VALUE knob. Press PARAMETER LEFT (<), then
dial to STANDARD mode or GUITAR mode. Press WRITE
Power on while holding PRESET PATCH and USER PATCH (keep holding until TAP TEMPO
©2010 Roland Corporation U.S.
Page 7
®
R
SH-32
SH-201
Sonic Cell
SP-202
SP-303
SP-404
SP-505
SP-606
SP-808
SPD-S
SPD-6
SPD-8
SPD-11/20
SPD-30
SRV-330
SRV-2000
SRV-3030/D
SX-700
Factory Reset Procedures
goes out). Press WRITE.
Power on while holding 1/A. Press the VALUE UP/DOWN buttons to select the desired
target to be initialized. Press WRITE/EXEC twice
Power on while holding PRESET and USER. Press WRITE.
Press MENU, then select UTILITY. Select FACTORY RESET, then select OK and press
CURSOR/VALUE.
CAUTION: This procedure will erase all of the internal samples and initialize the unit: Hold
down CANCEL and press DEL, then press the A/B button. Press DEL
Power on while holding CANCEL, REMAIN, DEL. Press REC
Power on while holding CANCEL, REMAIN, and DEL. When “ini” shows in the display,
press REC
Press SONG or PTN to display the Play screen. Press SYSTEM to display the system
screen. Press F1 (UTILITY). Press F3 (INIT). Set desired target to be initialized with
VALUE dial.(ALL, SYSTEM, SAMPLE, SEQ). Press F1 twice
Caution: Initializing the unit permanently deletes all samples out of the internal memory.
Press MENU. Press CURSOR to select “SYSTEM” and then press ENTER. Press F3 twice
Press SYSTEM/DISK and CURSOR to 4.Init SystemParam?. Press ENTER
Press SETUP. Press PAGE Right to select INIT/DELETE. Press ENTER. Use + or – to select
“ALL.” Press ENTER
Power on while holding DRUMS/U1, PERC/U2, SFX/U3 and OTHERS/U4. Press
OTHERS/U4 to execute the reset
Power on while holding EDIT, then press COPY. Use the VALUE UP (^) and DOWN (v) to
select F A L in the window. Press ALL/ENTER
Power on while holding ALL/ENTER and the DOWN ARROW button. Press ALL/ENTER
Press MENU. Use Knob 1 to select “SYSTEM” then press Button 3 [ENTER]. Press Button 2
to select the “F.RESET” tab. Use Knob 1 to select “Factory Reset” then press Button 3
[ENTER].
Power on while holding SYSTEM and PROGRAM. Use the DATA dial to select SYSTEM +
PROGRAM. Press MEMORY
Factory: Power on while holding WRITE and REVERB NON-LINEAR.
Delay Mode: Power on while holding WRITE, REVERB NON-LINEAR and ROOM SIMULATE
With the unit on, press MEMORY. Use NUMBER/ENTER dial to select FACTORY RESET. Press
NUMBER/ENTER twice
Press UTILITY. Use PARAMETER LEFT (<) and RIGHT (>) to select FACT INIT. Press WRITE
T
Model
TD-3
TD-4
TD-5
TD-6/V
TD-7
TD-7T
TD-8
TD-9
TD-10
TD-12
TD-20/20X
TMC-6
TR-505
TR-626
TR-707/727
Procedure
Power on while holding the + and – buttons. Release them, and then press DRUM KIT
Press MENU. Use the ^/v buttons to select “9 OPTIONS” then press OK. Use the ^/v
buttons to select “Factory Reset” then press OK. Use the Dial to select “All” then press the
SEL [v] button. Press OK.
Power on while holding EDIT and START/STOP, then press START/STOP again
Power on while holding SHIFT and EDIT SETUP. Press INC/+ to select ALL. Press ENTER
twice
Press SYSTEM. Use the LEFT (<) and RIGHT (>) CURSOR buttons to select INI, then
press ENTER. Cursor to HI HAT and use the DATA dial to select ALL. Press ENTER twice
Power on while holding SYSTEM and JUMP, then press ENTER
Press SETUP, then F3 MENU. Rotate VALUE to select “RESET.” Press F3 and use VALUE
to select ALL. Press F3 EXEC to execute
Press SETUP, then press F3 four times.
Press SETUP, then press F4 four times
Press SETUP, then press F5 three times
Press SETUP. Press F5 twice
Power on while holding TRIGGER SELECT and EDIT, release both then press EDIT again
Power on while holding MODE and PATTERN GROUP KEY A
Power on while holding MODE and TRACK #1
Power on while holding TRACK WRITE and TRACK #1
©2010 Roland Corporation U.S.
Page 8
®
R
TR-909
Factory Reset Procedures
Power on while holding TRACK #1 and PATTERN #1
U
Model
U-110
Procedure
Power on while holding PART and EDIT
V
Model
VA-3
VA-5/7
VA-76
V-BASS
VB-99
VF-1
VG-8/8EX
VG-88
VG-99
VGA-5/7
VK-7
VK-8
VK-8M
VK-77
VK-88
VK-1000
VM-3100/Pro
VM/C-7100/7200
V-Piano
VP-7
VP-70
VP-770
VP-9000
VR-700
V-Synth
V-Synth GT
V-SynthXT
VS-1880/1824CD
VS-2000CD
VS-2400CD
VS-2480
Procedure
Press FUNCTION/MENU. Touch [Global Parameter]. Touch [ALL]
Power on while holding MELODY/INTELL, CONTROLLERS and EFFECTS
With the unit on, press the FUNCTION/MENU button. Press ”GLOBAL PARAMETER” on
the touch screen. Then press ”ALL” on the touch screen
Power on while holding PAGE left and PAGE right. Press WRITE
Press [SYSTEM]. Press Page [>] to display Page 3. Press F2 [F.RST]. Select ALL , then
press F6 [EXEC]. Press WRITE.
With the unit on press UTILITY. Use NUMBER/VALUE dial to select “Factory Reset”. Press
NUMBER/VALUE three times
Power on while holding F1, F3, and F5. Press F6 for All, F4 for Patches, or F2 for System
Power on while holding PAGE (>) and PAGE (<). Press WRITE twice
Press SYSTEM. Press PAGE (>) to display page 3. Press F1 “F.RST.” Press F6 “EXEC” then
press WRITE.
Power on while holding WRITE. Release WRITE, then press WRITE again
Power on while holding MAIN, SUB and PEDAL in the HARMONIC BAR PART section
Power on while holding the UPPER, LOWER, and PEDAL buttons in the HARMONIC BAR
PART section. Release and re- press the UPPER, LOWER, and PEDAL buttons once again
With the unit on, confirm that the VOLUME is at the MIN position, then power off. Power
on while holding BAND, WRITE, and H-BAR MANUAL
Press EDIT. Use the RIGHT/LEFT ARROW buttons to select UTILITY and press ENTER.
Use the UP/DOWN ARROW buttons to select Factory Reset. Press WRITE, then press
ENTER
Power one while holding BANK, WRITE, and H-BAR MANUAL. Continue holding BANK,
WRITE, and H-BAR MANUAL until all panel indicators light.
Press WRITE, then press F3 to access the INIT MENU screen. Press F4 to access the
COLD BOOT screen, then press ENTER
Press SYSTEM, then press F1-F4 ON/OFF. Use the VALUE dial to put a check in the ALL
box and press ENTER three times
Power on while holding PROJECT/SYS and F1. Continue to press F1 until completed
Press FUNCTION so it is lit. Press F4 [UTILITY]. Use the VALUE dial to select “9. Initialize”
then press ENTER. Use the VALUE dial to select “2. Factory Reset All” then press ENTER.
Press F4 [Execute] then press F4 [OK].
Power on while holding BYPASS and FEMALE CHOIR.
Power on while holding PLAY, VOICE EXPANSION, and MIDI
Press MENU. Cursor to “Factory Reset” then press F2 [ENTER]. Press F1 [OK].
With the unit on, press UTILITY until it is lit. If the UTILITY Menu1 screen is displayed,
press PART/ >. (the UTILITY Menu2 screen will appear). Press F1 (FACTORY). Press
F6(EXEC)
Press FUNCTION/ENTER. Use the +/- buttons to display “Utl.” Press STRINGS, then press
FUNCTION/ENTER twice.
With the unit on, Press MODE. Touch FACORY RESET, then touch EXECUTE
Press UTILITY. Touch “FACTORY RESET,” then touch “EXECUTE.”
Press MODE. Touch “SYSTEM.” Touch “INIT.” Touch “EXECUTE.”
Hold shift and press F5/. Page to “INIT”. Press F1. Press ENTER/YES
Hold SHIFT and press F4 (Utility). Press PAGE to get to page 3. Press F1 (PrmIni). Press
F5. Press ENTER/YES
Hold SHIFT and press F4 (Utility). Press PAGE to get to page 3. Press F6 (PrmIni). Press
F5. Press ENTER/YES
Press UTILITY. Press PAGE to get to page 3. Press F6 (PrmIni). Press F5. Press
©2010 Roland Corporation U.S.
Page 9
®
R
VT-1
W
Model
W-50
X
Model
XP-10
XP-30
XP-50
XP-60/80
XV-88
XV-2020
XV-3080
XV-5050
XV-5080
Factory Reset Procedures
ENTER/YES
Power on while holding down the PRESET/USER button
Procedure
Press CONTROL and MASTER simultaneously. Use PARAMETER UP (^) and DOWN (v) to
select ALL. Press VALUE UP (^)
Procedure
Press UTILITY. Use VALUE + and - to select INITIALIZE, then press ENTER. Use VALUE +
and - to select FACTORY PRESET, then press ENTER
Press UTIL/CARD and use the CURSOR buttons to select 4:FACTORY RESET. Press ENTER
three times. If Write Protect is on, press DEC once, then press ENTER three times
Press DISK/UTILITY, select SOUND, select PRESET, then press ENTER. Use the dial to
turn Memory Protect OFF if necessary, then press ENTER twice
Press UTILITY, press F6 (MENU) twice to select Factory, then ENTER. Press F6
(EXECUTE). Use the dial to turn Memory Protect OFF if necessary, press ENTER, then
press F6 (EXECUTE)
With the unit on, press UTILITY. Cursor down to Utility Menu 2. Cursor right 3 times to
select “FACTORY RESET”. Press ENTER twice. If Internal Write Protect is set to ON, turn
the VALUE dial to select OFF, then press ENTER 3 times
While holding down VOLUME, press VALUE. Release them, then turn CATEGORY/BANK to
select “PIANO.” Rotate VALUE until “Fct” shows in the display. Press VALUE Twice
With unit on, press UTILITY. Press UP or DOWN cursor buttons to select the UTIL 2 page.
Use LEFT or RIGHT cursor buttons to select “FACTORY RESET”. Press ENTER twice
With the unit on, press UTILITY. Press CURSOR left until “FACTORY RESET” shows in the
display. Press ENTER twice. If “WRITE PROTECT ON” is displayed, turn the VALUE dial to
select “OFF”, then press ENTER twice
With the unit on, press SYSTEM/UTILITY. Press F6 [MENU] to select menu 3. Press
F1[FACTORY], then press F6 [FACTORY]. If “INT WRITE PROTECT=ON” is displayed,
press DEC, then press F6 twice
©2010 Roland Corporation U.S.
Page 10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising