LogiComm Systems for Nonwovens Production Brochure

LogiComm Systems for Nonwovens Production Brochure
LogiComm®
Pattern Control System
Modular, touch-screen system
delivers precise pattern control
with advanced features.
The integrated LogiComm system is a comprehensive, easily
installed pattern control. Multiple, remote touch-screens can
be positioned virtually anywhere on the parent machine for
easy operation. This modular system features a building-block
approach. Initial installation of a 4-channel pattern control
can later be expanded to as many as 32 channels.
The programmable control system allows quick pattern
programming and changeovers even on complex applications.
Standard Pattern Control Features:
n A
bility to support multiple, advanced patterns in
continuous or intermittent operation.
n
n
n
n
M
ulti-zone, multi-point pressure control across full
machine speed range.
Advanced Features:
n B
locked photocell warning – occurs if photocell is ON
continuously or too long.
n
n
M
ultiple program memory.
I ntegral gun drivers control all types of Nordson hot melt
and additive applicators.
D
evice naming (guns, triggers, pressure) for application
specific identification.
n
n
n
Multi-module configuration
O
ver length warning – occurs if the length of the product
increases due to jamming or where several cartons stick
together.
U
nder length warning – occurs if the product is too short;
prevents adhesive from being dispensed on the machine.
S
ystem I/O – stops parent machine due to warnings from
over length, under length or blocked photocell.
T
rigger masking – distance over which no trigger is
generated.
A
larm – occurs if guns, triggers or associated cables are
disconnected, short circuited or open.
LogiComm®
Pattern Control System
Specifications
Maximum Line Speed 1200 m/min (3937 ft/min)
Pattern Accuracy ±0.25 mm (0.01 in.)
Encoder Resolution up to 30 pulses per mm
Encoder Frequency 100 KHz maximum
Electrical Service Universal 80-256 VAC, 1 Ph.
Program Memories Virtually unlimited (via Flash Memory Card)
Encoders 1 or 2 per system
Pattern Channels 4 or 8 per control module (up to 32 per standard system)
Gun Outputs 4 or 8 gun output connectors per module
(one gun connector per pattern channel)
Gun Drivers
Universal™ Gun Driver 80 watts per gun driver (4 guns), 160 watts per module
Low Voltage Driver
80 watts per module
Pressure Outputs 2 or 4 per control module (up to 16 per standard system),
each with multipoint curves
Independent Triggers 4 or 8 per control module (up to 32 per standard system)
Adaptable to PNP or NPN type. Freely assignable to any gun and can
be shared between guns.
Parent Machine I/O
4 in 4 out programmable
For more
information,
speak with your
Nordson
representative
or contact
your Nordson
regional office.
United States
Duluth, Georgia
(800) 683-2314 Phone
(866) 667-3329 Fax
Europe
Luneburg, Germany
(49) 4131-894-0 Phone
(49) 4131-894-149 Fax
Japan
Tokyo, Japan
(81) 3-5762-2700 Phone
(81) 3-5762-2701 Fax
Asia/Australia/
Latin America
Amherst, Ohio
(440) 985-4496 Phone
(440) 985-1096 Fax
Find us on:
The LogiComm system’s modularity
allows installation of 4-channel pattern
control along with the ability to add
capacity as needed to the 32-channel
maximum.
NWL-15-5884
Reissued 2/15
© 2007, 2015 Nordson Corporation
All Rights Reserved.
Printed in U.S.A.
Nordson reserves the right to make
design changes between printings.
Nordson Corporation
11475 Lakefield Drive
Duluth, GA 30097-1511
(800) 683-2314
nordson.com/adhesive
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising