VSP 5162 User’s Guide Manual #：RGB-RD-UM-V5162 E001 Revision:V1.3 – VSP 5162 User’s Guide 1 VSP 5162·User’s Guide Thank you for choosing our products! In order to allow you to learn how to use the video processor quickly, we bring you the detailed user’s guide. You can read the introduction and directions before using the video processor, please read all the information we provide carefully to use our products correctly. Copyright ©2012 All rights reserved by RGBLINK. This document is done by Xiamen RGBlink Science & Technology Co.,Ltd independently. No part may be copied, reproduced or translated without permission. Notice RGBlink provides this manual “as is” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. RGBlink may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice. This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this publication; these changes are incorporated in new editions of this publication. Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be responsible for correcting any interference. VSP 5162 User’s Guide 2 Guarantee and Compensation RGBlink provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults. RGBlink must be informed immediately in writing of any complains. The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of compliant, RGBlink can repair the fault or provide a replacement at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or indirect damage, and also damage attributed to the operation of software as well as to other service provided by RGBlink, being a component of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties guaranteed in writing or due to the intent or gross negligence or part of RGBlink. If the purchaser or a third party carries out modifications or repairs on goods delivered by RGBlink, or if the goods are handled incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee provided by RGBlink either. The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the customer. Trademarks Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufactures. VSP 5162 User’s Guide 3 Company address Xiamen RGBlink Science & Technology Co., Ltd. Headquarter: S603~604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C Shenzhen office: Building 3, A Baiwang Plaza, Xili Nanshan District, Shenzhen, Guangdong Province, P.R.C Beijing office：Room 602, Building 7, CaiManJie, No.67 Chaoyang Road, Chaoyang District, Beijing, P.R.C Shanghai office：Building 3, 1358 Nong, Tongpu Road, Shanghai, P.R.C Tel: +86-592-5771197 Fax：+86-592-5771202 Websites： ~ ~ http://www.rgblink.com http://www.rgblink.cn E-mail：[email protected] VSP 5162 User’s Guide 4 Operators Safety Summary The general safety information in this summary is for operating personnel. Do Not Remove Covers or Panels There are no user-serviceable parts within the unit. Removal of the top cover will expose dangerous voltages. To avoid personal injury, do not remove the top cover. Do not operate the unit without the cover installed. Power Source This product is intended to operate from a power source that will not apply more than 230 volts rms between the supply conductors or between both supply conductor and ground. A protective ground connection by way of grounding conductor in the power cord is essential for safe operation. Grounding the Product This product is grounded through the grounding conductor of the power cord. To avoid electrical shock, plug the power cord into a properly wired receptacle before connecting to the product input or output terminals. A protective-ground connection by way of the grounding conductor in the power cord is essential for safe operation. Use the Proper Power Cord Use only the power cord and connector specified for your product. Use only a power cord that is in good condition. Refer cord and connector changes to qualified service personnel. Use the Proper Fuse To avoid fire hazard, use only the fuse having identical type, voltage rating, and current rating characteristics. Refer fuse replacement to qualified service personnel. Do Not Operate in Explosive Atmospheres To avoid explosion, do not operate this product in an explosive atmosphere. VSP 5162 User’s Guide 5 Terms In This Manual and Equipment Marking WARNING Highlights an operating procedure, practice, condition, statement, etc, which, if not strictly observed, could result in injury or death of personnel. Note Highlights an essential operating procedure, condition or statement. CAUTION The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. VSP 5162 User’s Guide 6 Change History The table below lists the changes to the Video Processor User’s Guide. Format Time ECO# Description Principal V1.0 2011-12-08 0000 Release V1.1 2012-03-19 0001 Add PIP function Add Cascade for Mosaic function Add USD input Add standard SDI detect Add TP setting from LCD panel Add TP Button’s function Update output resolution Peter V1.2 2012-04-25 0002 Perfect seamless switch BIN V1.3 2012-07-11 0003 All-new version of guide style BIN VSP 5162 User’s Guide BIN 7 CONTENT CONTENT .............................................................................................. 8 1. Introduction ............................................................................... 16 Chapter Structure ........................................................................................ 17 How to Use This Guide .............................................................................. 18 Terms and Definitions ................................................................................. 19 System Overview ........................................................................................ 24 Application Questions ................................................................................ 25 2. Hardware Orientation ................................................................ 26 In This Chapter ............................................................................................ 26 VSP 5162 Rear Panel ................................................................................ 27 INPUT Interface ................................................................................................. 27 1~4：CVBS Input.............................................................................................. 27 5.16.17.18: DVI Input....................................................................................... 28 6.19: VGA Input ................................................................................................ 28 Front Panel USB Input .................................................................................... 28 CONT Interface ................................................................................................ 29 7. Dial Switch .................................................................................................... 29 8. 10/100M Interface ........................................................................................ 29 9. USB Interface ............................................................................................... 29 10. RS232 Interface ......................................................................................... 29 OUTPUT Interface ........................................................................................... 29 VSP 5162 User’s Guide 8 11.12.22.23: Gigabit copper port.................................................................... 29 13.24：Power supply port of Sending Card ................................................. 29 14.25：USB control port of sending card ..................................................... 29 15.26：DVI Input.............................................................................................. 29 20：DVI Output ................................................................................................ 29 21：DVI +VGA DVI Output ............................................................................. 30 Switch and Power ............................................................................................ 30 27：Power Interface and Switch.................................................................... 30 VSP 5162 Front Panel..................................................................................... 31 LCD Panel ............................................................................................................ 33 Buttons ............................................................................................................... 33 Signal keys:.......................................................................................................... 34 Program .............................................................................................................. 34 Preview ............................................................................................................... 34 Function .............................................................................................................. 35 3. Hardware Installation ................................................................ 39 In This Chapter ............................................................................................ 39 Safety Precautions...................................................................................... 40 Unpacking and Inspection ......................................................................... 40 Site Preparation .......................................................................................... 40 4. Menu Orientation ...................................................................... 41 In This Chapter ............................................................................................ 41 VSP 5162 User’s Guide 9 PRG .............................................................................................................. 42 WIPE ............................................................................................................. 43 OUT .............................................................................................................. 45 SCALE .......................................................................................................... 46 MENU ........................................................................................................... 47 MENU---Status ................................................................................................. 48 MENU---Reset .................................................................................................. 48 MENU--- Language .......................................................................................... 48 MENU--- OUTPUT ........................................................................................... 48 MENU--- Scale ................................................................................................. 49 MENU--- Advance ............................................................................................ 49 MENU---Picture ................................................................................................ 50 MENU---Matrix.................................................................................................. 51 MENU--- Time ................................................................................................... 51 MENU--- Date ................................................................................................... 51 MENU---PTP..................................................................................................... 52 MENU---Crop .................................................................................................... 52 MENU---TP Color ............................................................................................. 52 MENU--- SDI..................................................................................................... 52 5. Communication Software Guideline ........................................... 53 In This Chapter ............................................................................................ 53 Install Software ............................................................................................ 54 VSP 5162 User’s Guide 10 Run software ............................................................................................... 58 Set Up Communication ................................................................................... 58 Preview .............................................................................................................. 61 Programme ....................................................................................................... 61 Output resolution toolbar ................................................................................. 62 Current config mode ........................................................................................ 62 Call saving modes ............................................................................................ 62 FS ....................................................................................................................... 63 CUT .................................................................................................................... 63 Take ................................................................................................................... 63 Effects Toolbar .................................................................................................. 63 Fade in and fade out toolbar........................................................................... 64 Fade duration.................................................................................................... 64 Width of transparent toolbar ........................................................................... 64 Configuration .................................................................................................... 65 Input setting ...................................................................................................... 65 Input source choice .......................................................................................... 65 Input resolution toolbar .................................................................................... 65 Display ............................................................................................................... 65 Ratio................................................................................................................... 65 Output timer polar ............................................................................................ 66 Image Quality Setting ...................................................................................... 66 VSP 5162 User’s Guide 11 Mode configuration .......................................................................................... 66 Image input toolbar .......................................................................................... 67 Operational mode selection Interface ........................................................... 67 Set ...................................................................................................................... 70 Save ................................................................................................................... 70 Update reset ..................................................................................................... 70 Control ............................................................................................................... 71 Cascade control ............................................................................................... 71 Delay time ..........................................................................................................74 DVI DE DELAY ..................................................................................................74 VGA input adjustment ...................................................................................... 75 IP setting ........................................................................................................... 75 Factory reset ......................................................................................................76 Option .................................................................................................................76 Language ...........................................................................................................76 Administration ....................................................................................................76 Advance option, for administrator control ......................................................76 Help .................................................................................................................... 77 Version notice ................................................................................................... 77 About.................................................................................................................. 77 Information toolbar ........................................................................................... 77 How to control processor through RS232? ............................................. 78 VSP 5162 User’s Guide 12 How to control processor with console software by USB? ................... 81 6. System Setup and Operations .................................................... 85 In This Chapter ............................................................................................ 85 Interface and Input Single Option ............................................................. 86 Key Operation of Signal Format Selection ................................................... 87 Single Picture Single Switch ..................................................................... 88 Button Save User Mode Operations.............................................................. 88 Single Image Switch ........................................................................................ 88 Blackburst Switch ............................................................................................. 89 Scale .................................................................................................................. 89 PIP Setting ................................................................................................... 90 Each Image Width, Heigh and Position Setting ........................................... 90 Console Software Setting Each Image's Width, Heigh and Position ........ 91 USB Input Setting ....................................................................................... 92 Keyboard operation ......................................................................................... 92 Console software operation ............................................................................ 93 Cascade Setting .......................................................................................... 94 Basic Working Principle................................................................................... 94 Simple Structure Connect Guide.................................................................... 95 Set display Parameters for Each Processor Each Input and Save ........... 95 Central Control Setting Guide ........................................................................ 99 VSP5162 Common Serial Command Set (Serial Protocol) ..................... 101 VSP 5162 User’s Guide 13 7. Common Questions and Solution ............................................. 103 In This Chapter .......................................................................................... 103 No Output in Large Screen ...................................................................... 104 Confirm if there are any input singles .......................................................... 104 Confirm if single output.................................................................................. 104 Large Screen Output Flash Point ........................................................... 104 Confirm if monitor output is normal.............................................................. 104 Large Screen only Display Part of the Image ....................................... 105 Signal need to scale ...................................................................................... 105 No Display in the Second Half Part of Large Screen........................... 105 Resolution is inadequate ............................................................................... 105 Sending card can't take lower part .............................................................. 105 Large Screen Shaking.............................................................................. 105 Sending card input recognition is not correct ............................................. 105 Left of the Screen Appears Two Black Sides ....................................... 106 Adjust DE deviation ....................................................................................... 106 Adjust each output offset value .................................................................... 106 All Key Lights Light Simultaneously ....................................................... 106 Check if dial switches are normal ................................................................ 106 A. Specification................................................................................. 107 B. Contact Information ..................................................................... 109 C. Upgrading Software ...................................................................... 110 VSP 5162 User’s Guide 14 How to upgrade VSP 5162 firmware?.................................................... 110 Download the IP software ........................................................................ 112 VSP 5162 User’s Guide 15 1. Introduction This chapter is designed to introduce you to the VSP 5162 User’s Guide. Areas to be covered are: Chapter Structure How to Use This Guide Terms and Definitions System Overview Application Questions VSP 5162 User’s Guide 16 1. Introduction Chapter Structure Chapter Structure The following chapters provide instructions for all aspects of VSP 5162 operations. Chapter 1 Introduction Chapter 2 Hardware Orientation Chapter 3 Hardware Installation Chapter 4 Menu Orientation Chapter 5 Communication Software Guideline Chapter 6 System Setup and Operations Chapter 7 Common Questions and Solution Appendix A Specification Appendix B Contact information Appendix C Upgrading Software VSP 5162 User’s Guide 17 1. Introduction How to Use This Guide How to Use This Guide Following are important tips for streamlining your use of this User’s Guide in its electronic “PDF” form. Navigating Use Acrobat Reader’s “bookmarks” to navigate to the desired location. All chapter files have the same bookmark structure for instant navigation to any section. Please note: Extensive hyperlinks are provided within the chapters. Use Acrobat’s “Go to Previous View” and “Return to next View” buttons to trace your complete navigational path. Use the “Previous Page” and “Next Page” buttons to go to the previous or next page within a file. Use Acrobat’s extensive search capabilities, such as the “Find” tool and “Search Index” tool to perform comprehensive searches as required. Table of Contents and Index Use the Table of Contents bookmarks to navigate a desired topic. Click any item to instantly jump to that section of the guide. You c an also use the Index to jump to specific topics within a chapter. E ach page number in the Index is a hyperlink. General Operations To ensure trouble-free operation, please follow all procedures as listed below: For detailed installation instructions, refer to chapter 3 “Hardware Installation” on page 39. For communication software control guide, refer to Chapter 5, “Communication Software Control Guide” on page 53. For system setup and operations, refer to Chapter 6, “System Setup and Operations” on page 85. Should you have any questions regarding the installation or operation of VSP 5162, please consult with the factory. Refer to Appendix C, “Upgrading Software” on page 110 for contact information. VSP 5162 User’s Guide 18 1. Introduction Terms and Definitions Terms and Definitions The following terms and definitions are used throughout this guide. “ASCII”: American Standard for Information Interchange. The standard code consisting of 7-bit coded characters (8 bits including parity check) used to exchange information between data processing systems, data communication systems, and associated equipment. The ASCII set contains control characters and graphic characters. “Aspect ratio”: The relationship of the horizontal dimension to the vertical dimension of an image. In viewing screens, standard TV is 4:3, or 1.33:1; HDTV is 16:9, or 1.78:1. Sometimes the “:1” is implicit, making TV = 1.33 and HDTV = 1.78. “AV”: Audio visual, or audio video. A “Background” is an unscaled source, typically originating from a computer. Abackground source appears at the system’s lowest priority — visually in back of all other sources. “Baudrate”：Named of J.M.E. Baudot, the inventor of the Baudot telegraph code. The number of the electrical oscillations per second, called baud rate. Related to, but not the same as, transfer rate in bits per second (bps). “Blackburst”: The video waveform without the video elements. It includes the vertical sync, horizontal sync, and the chroma burst information. Blackburst is used to synchronize video equipment to align the video output. One signal is normally used to set up an entire video system or facility. Sometimes it is called House sync. “BNC”: Bayonet Neill-Concelman. A cable connector used extensively in television and named for its inventors. A cylindrical bayonet connector that operates with a twist-locking motion. To make the connection, align the two curved grooves in the collar of the male connector with the two projections on the outside of the female collar, push, and twist. This allows the connector to lock into place without tools. “Brightness”: Usually refers to the amount or intensity of video light produced on a screen without regard to color. Sometimes called “black level. “CAT 5”: Category 5. Describes the network cabling standard that consists of four unshielded twisted pairs of copper wire terminated by RJ-45 connectors. CAT 5 cabling supports data rates up to 100 Mbps. CAT 5 is based on the EIA/TIA 568 Commercial Building Telecommunications Wiring Standard. “Color bars”: A standard test pattern of several basic colors (white, yellow, cyan, green, magenta, red, blue, and black) as a reference for system alignment and testing. In NTSC video, the most commonly used color bars are the SMPTE standard color bars. In PAL video, the most commonly used color bars are eight full field bars. In the computer, the most commonly used color bars are two rows of reversed color bars. “Color burst”: In color TV systems, a burst of subcarrier frequency located on the back porch of the composite video signal. This serves as a color synchronizing signal to establish a frequency and phase reference for the chroma signal. Color burst is 3.58 MHz for NTSC and 4.43 MHz for PAL. “Color temperature”: The color quality, expressed in degrees Kelvin(K), of a light source. The higher the color temperature, the bluer the light. The lower the temperature, the redder the light. Benchmark VSP 5162 User’s Guide 19 1. Introduction Terms and Definitions color temperature for the A/V industry include 5000°K, 6500°K, and 9000°K. “Contrast ratio”: The radio of the high light output level divided by the low light output level. In theory, the contrast radio of the television system should be at least 100:1, if not 300:1. In reality, there are several limitations. In the CRT, light from adjacent elements contaminate the area of each element. Room ambient light will contaminate the light emitted from the CRT. Well-controlled viewing conditions should yield a practical contrast ratio of 30:1 to 50:1. “DVI”: Digital Visual Interface. The digital video connectivity standard that was developed by DDWG (Digital Display Work Group). This connection standard offers two different connectors: one with 24 pins that handles digital video signals only, and one with 29 pins that handles both digital and analog video. “EDID”: Extended Display Identification Data – EDID is a data structure used to communicate video display information, including native resolution and vertical interval refresh rate requirements, to a source device. The source device will then output the optimal video format for the display based on the provided EDID data, ensuring proper video image quality. This communication takes place over the DDC – Display Data Channel. “Ethernet”: A Local Area Network (LAN) standard officially known as IEEE 802.3. Ethernet and other LAN technologies are used for interconnecting computers, printers, workstations, terminals, servers, etc. within the same building or campus. Ethernet operates over twisted pair and over coaxial cable at speeds starting at 10Mbps. For LAN interconnectivity, Ethernet is physical link and data link protocol reflecting the two lowest layers of the OSI Reference Model. “Frame”: In interlaced video, a frame is one complete picture. A video frame is made up of two fields, or two sets of interlaced lines. In a film, a frame is one still picture of a series that makes up a motion picture. “Gamma”: The light output of a CRT is not linear with respect to the voltage input. The difference between what you should have and what is actually output is known as gamma. “HDMI” - High – Definition Multimedia Interface: An interface used primarily in consumer electronics for the transmission of uncompressed high definition video, up to 8 channels of audio, and control signals, over a single cable. HDMI is the de facto standard for HDTV displays, Blu-ray Disc players, and other HDTV electronics. Introduced in 2003, the HDMI specification has gone through several revisions. “HDSDI”: The high-definition version of SDI specified in SMPTE-292M. This signal standard transmits audio and video with 10 bit depth and 4:2:2 color quantization over a single coaxial cable with a data rate of 1.485 Gbit/second. Multiple video resolutions exists including progressive 1280x720 and interlaced 1920x1080 resolution. Up to 32 audio signals are carried in the ancillary data. “JPEG” (Joint photographic Expects Group): Commonly used method of lossy compression for photographic images using a discreet cosine transfer function. The degree of compression can be adjusted, allowing a selectable tradeoff between storage size and image quality. JPEG typically achieves 10:1 compression with little perceptible loss in image quality. Produces blocking artifacts. “MPEG”: Motion Picture Expect Group. A standard committee under the auspices of the International Standards Organization working on algorithm standards that allow digital compression, storage and VSP 5162 User’s Guide 20 1. Introduction Terms and Definitions transmission of moving image information such as motion video, CD-quality audio, and control data at CD-ROM bandwidth. The MPEG algorithm provides inter-frame compression of video images and can have an effective compression rate of 100:1 to 200:1. “NTSC”: The color video standard used in North America and some other parts of the world created by the National Television Standards Committee in the 1950s. A color signal must be compatible with black-and-white TV sets. NTSC utilizes an interlaced video signals, 525 lines of resolution with a refresh rate of 60 fields per second (60 Hz). Each frame is comprised of two fields of 262.5 lines each, running at an effective rate of 30 frames per second. “PAL”: Phase Alternate Line. A television standard in which the phase of the color carrier is alternated from line to line. It takes four full pictures (8 fields) for the color-to-horizontal phase relationship to return to the reference point. This alternation helps cancel out phase errors. For this reason, the hue control is not needed on a PAL TV set. PAL, in many transmission forms, is widely used in Western Europe, Australia, Africa, the Middle East, and Micronesia. PAL uses 625-line, 50-filed (25 fps) composite color transmission system. “Operator”: Refers to the person who uses the system. “PIP”: Picture-in-Picture. A small picture within a larger picture created by scaling down one of the images to make it smaller. Each picture requires a separate video source such as a camera, VCR, or computer. Other forms of PIP displays include Picture-by-Picture (PBP) and Picture-with-Picture (PWP), which are commonly used with 16:9 aspect display devices. PBP and PWP image formats require a separate scaler for each video window. “Polarity”: The positive and negative orientation of a signal. Polarity usually refers to the direction or a level with respect to a reference (e.g. positive sync polarity means that sync occurs when the signal is going in the positive direction). “RJ-45”: Registered Jack-45. A connector similar to a telephone connector that holds up to eight wires, used for connecting Ethernet devices. “RS-232”: An Electronic Industries Association (EIA) serial digital interface standard specifying the characteristics of the communication path between two devices using either DB-9 or DB-25 connectors. This standard is used for relatively short-range communication and does not specify balanced control lines. RS-232 is a serial control standard with a set number of conductors, data rate, word length, and type of connector to be used. The standard specifies component connection standards with regard to the computer interface. It is also called RS-232-C, which is the third version of the RS-232 standard, and is functionally identical to the CCITT V.24 standard. “Saturation”: Chroma, chroma gain. The intensity of the color, or the extent to which a given color in any image is free from white. The less white in a color, the truer the color or the greater its saturation. On a display device, the color control adjusts the saturation. Not to be VSP 5162 User’s Guide 21 1. Introduction Terms and Definitions confused with the brightness, saturation is the amount of pigment in a color, and not the intensity. Low saturation is like adding white to the color. For example, a low-saturated red looks pink. “Scaling”: A conversion of a video or computer graphic signal from a starting resolution to a new resolution. Scaling from one resolution to another is typically done to optimize the signal for input to an image processor, transmission path or to improve its quality when presented on a particular display. “SDI”: Serial Digital Interface. The standard based on a 270 Mbps transfer rate. This is a 10-bit, scrambled, polarity independent interface with common scrambling for both component ITU-R 601 and composite digital video and four channels of (embedded) digital audio. “Seamless Switching”: A feature found on many Extron video switchers. This feature causes the switcher to wait until the vertical interval to switch. This avoid a glitch (temporary scrambling) which normally is seen when switching between sources. “SMPTE”: Society of Motion Picture and Television Engineers. A global organization, based in the United States, that sets standards for baseband visual communications. This includes film as well as video and television standards. “S-video”: A composite video signal separated into the luma (“Y” is for luma, or black and white information; brightness) and the chroma (“C” is an abbreviation for chroma, or color information). “Sync”: Synchronization. In video, sync is a means of controlling the timing of an event with respect to other events. This is accomplished with timing pulses to insure that each step in a process occurs at the correct time. For example, horizontal sync determines exactly when to begin each horizontal scan line. Vertical sync determines when the image is to be refreshed to start a new field or frame. There are many other types of sync in video system.(Also known as “sync signal” or “sync pulse.”) “TCP/IP”: Transmission Control Protocol/Internet Protocol. The communication protocol of the Internet. Computers and devices with direct access to the Internet are provided with a copy of the TCP/IP program to allow them to send and receive information in an understandable form. “USB”: Universal Serial Bus. USB was developed by seven PC and telecom industry leaders (Compaq, DEC, IBM, Intel, Microsoft, NEC, and Northern Telecom). The goal was easy plug-and-play expansion outside the box, requiring no additional circuit cards. Up to 127 external computer devices may be added through a USB hub, which may be conveniently located in a keyboard or monitor. USB devices can be attached or detached without removing computer power. The VSP 5162 User’s Guide 22 1. Introduction Terms and Definitions number of devices being designed for USB continues to grow, from keyboards, mice, and printers to scanners, digital cameras, and ZIP drives. “VESA”: Video Electronics Standards Association. A nonprofit number organization dedicated to facilitating and promoting personal computer graphics through improved standards for the benefit of the end-user. www.vesa.org “VGA”: Video Graphics Array. Introduced by IBM in 1987, VGA is an analog signal with TTL level separate horizontal and vertical sync. The video outputs to a 15-pin HD connector and has a horizontal scan frequency of 31.5 kHz and vertical frequency of 70 Hz (Mode 1, 2) and 60 Hz (Mode 3). The signal is non-interlaced in modes 1, 2, and 3 and interlaced when using the 8514/A card (35.5 kHz, 86 Hz) in mode 4. It has a pixel by line resolution of 640×480 with a color palette of 16 bits and 256,000 colors. “YCrCb”: Used to describe the color space for interlaced component video. “YPbPr”: Used to describe the color space for progressive-scan (non-interlaced) component video. VSP 5162 User’s Guide 23 1. Introduction System Overview System Overview The VSP 5162 is a dual channel video processor that accepts a wide variety of video signals, including RGB computer video, HDTV video. It combines truly seamless, glitch-free switching with advanced scaling technologies to meet the requirements of high quality, high resolution video presentations. With multiple transition effects like curtain, wipe, fade in fade out etc, it makes the performance perfect. It supports user defined image size and coordinate, dual image processing, multiple splicing modes, pixel to pixel mapping, several user configurations and multiple ways of controlling, lots of advanced functions in high-end show are available. Features: Processing: • True Seamless switching • High quality scaling technology • 10-bit sampling and internal processing/scaling • Short video delay Multiple inputs • VSP 5162 provides 4 x composite (CVBS), 2x USB, 2x DVI (compatible with HDMI 1.3), 2xVGA, 1 x3G self-adaptive SDI input (3G SDI module), 2x DVI input (Compatible with HDTV and HDMI, HD Component, PC DVI video or PC RGB video signal) for the application in different environments. Wherein, both 3G SDI input or DVI+VGA inputs is optional module. Multiple outputs: • 1 x Preview VGA output • 2 X DVI outputs are provided for splitting into two different pictures or distributing the same two pictures, the two DVI outputs can be connected with LED display or other display. Preview Operation • Users can preview all the programmed inputs one by one on the defined outputs, such as monitor. User can check the inputs before take it to the target output. With preview function, user can use VSP 5162S for safe control. Multiple Control Methods • Front Panel, RS232、USB, Ethernet. VSP 5162 User’s Guide 24 1. Introduction Application Question Application Questions RGBlink offers solutions to demanding technical problems. Any application questions, or required further information, please contact with our Customer Support Engineers. Refer to Appendix B for contact details. VSP 5162 User’s Guide 25 2. Hardware Orientation In This Chapter This chapter provides detailed information about the VSP 5162 hardware. The following topics are discussed: VSP 5162 Rear Panel VSP 5162 Front Panel VSP 5162 User’s Guide 26 2. Hardware Orientation VSP 5162 Rear Panel VSP 5162 Rear Panel The figure below illustrates the professional interface and control signals of VSP 5162 rear panel. NO. INTERFACE NO. INTERFACE 1~4 CVBS Input 11.12.22.23 Gigabit copper port 5.16.17.18 DVI Input 13.24 Power supply port of Sending Card 6.19 VGA Input 14.25 USB control port of sending card 7 Dial Switch 15.26 DVI Input 8 10/100M Interface 20.21 DVI Output 9 USB Interface 27 Switch and Power 10 RS232 Interface INPUT Interface 1) 4 CVBS inputs by BNC interfaces. CV1 is compatible with 3G SDI input; 2) 4 DVI inputs by DVI-I interface. DVI1 and DVI2 can be compatible with HDMI, and can be used as VGA inputs; 3) 4 VGA inputs, 2 by DVI1 and DVI2, another two by VGA input interfaces. VGA input is compatible with component; 4) 2 USB inputs on the front panel by USB-D interfaces. 1~4：CVBS Input CVBS 1/2/3/4 input. Can receive standard video signal from players, cameras etc. Input supported resolution 480i and 576i via BNC. VSP 5162 User’s Guide 27 2. Hardware Orientation VSP 5162 Rear Panel Supported standards include: PAL, NTSC and SECAM. Connector 1 can be compatible with 3G-SDI input if select 3G SDI module. 5.16.17.18: DVI Input DVI 5/16/17/18 input. Can receive video signal from HD player, DVD, Computer video signal via DVI connector, input supported resolution: 1080P50/59.94/60,1080i50/59.94/60, 720p50/59.94/60；PAL；NTSC, VESA：1024×768×60Hz，1280×768×60Hz，1280×1024×60Hz, 1440×900×60Hz, 1680×1050×60Hz, 1600×1200×60Hz, 1920×1080×60Hz; Note DVI-I 5/18 interface can only support VESA:1024×768×60Hz， 1280×768×60Hz，1280×1024×60Hz， 1440×900×60Hz，1680×1050×60Hz， 1600×1200×60Hz，1920×1080×60Hz； Note DVI-I 16/17 is compatible with VGA and YPbPr. Via adapter, can access DVI signal, or Via adapter, input VGA video, or via adapter, input YPbPr Hd component video. 6.19: VGA Input VGA 6/19 Input Interface, input the video signal from HD player and Computer, etc. Input signal via the DB15 interface. Front Panel USB Input VSP 5162 User’s Guide 28 2. Hardware Orientation VSP 5162 Rear Panel USB 1/2 media player input interface, can access USB device or mobile hard disk with USB storage function. Support image format: JPGE, BMP, PNG; and support video format: MP4, MPEG1, MPEG2, RMVB, MJPG. CONT Interface 7. Dial Switch 8. 10/100M Interface 9. USB Interface Remote communication device control interface, used to connect the computer. 10. RS232 Interface Used to connect the computer. OUTPUT Interface 11.12.22.23: Gigabit copper port Gigabit copper port, connect to LED screen. 13.24：Power supply port of Sending Card Power has been already supplied by video processor itself, no external power supply needed. 14.25：USB control port of sending card 15.26：DVI Input Input the DVI out originating from other video processors.（This DVI connector does not support hot-plugging） 20：DVI Output Connect to the monitor or LED screen which has DVI interface（This DVI connector does not support hot-plugging）. VSP 5162 User’s Guide 29 2. Hardware Orientation VSP 5162 Rear Panel 21：DVI +VGA DVI Output DVI +VGA output via DVI connector, connect to the monitor or LED screen which has DVI interface.（This DVI connector does not support hot-plugging）. DVI +VGA , VGA output connector can be connected to monitor or projector which has VGA interface. Note adapter, can connect with Via DVI-based or VGA-based equipment, and via DVI to VGA adapter, can output VGA only. Switch and Power 27：Power Interface and Switch AC 90-264V 3.8A 50/60Hz VSP 5162 IEC-3 Power Interface User’s Guide 30 2. Hardware Orientation VSP 5162 Front Panel VSP 5162 Front Panel Insert power cord and push power to ON position. LCD module on the front panel will show RGBLINK and go into self verification before it load last setting config and send processed image to the target monitor. For the first setup, DVI input is default source. With front panel keyboard, user can operate VSP 1121 through the menus on LCD panel. VSP 5162 front panel as shown in figure: RGBLINK 视诚科技 亮彩系列 AVDSP SeriesVSP 5162 Initializing Almost there…… Can be connected to LAN via cable, it’ll indicate DHCP Failed if not connected. DHCP Failed As shown in figure: Assign IP addresses automatically when connected network, as shown in figure: VSP 5162 User’s Guide IP Address 192.168.0.100 31 2. Hardware Orientation VSP 5162 Front Panel System enters circulation state: Recycling process indicates that the current programme input format, preview input format, current output format, the current program version information, current equipment serial number. Users hold equipment serial number will get more effective service and support. 5秒 Program 1:CV1 720 x 576x50i Preview 1:CV1 720 x 576x50i 5秒 5秒 RGBlink SN:AM0169 Output Format: 1024x768x60 5 seconds IP Address 192.168.0.100 VSP 5162 5 seconds Software Version 2.31 User’s Guide 32 2. Hardware Orientation VSP 5162 Front Panel VSP 5162 front panel as following: LCD Panel used to show button menu and menus for interactive communication； Buttons press ESC to quit from current menu; Press SEL to confirm the current menu or value; press this button to select the previous item or increase a value; press this button to select the previous item or decrease a value; press this button to select the item on the left; press this button to select the item on the right; VSP 5162 User’s Guide 33 2. Hardware Orientation VSP 5162 Front Panel Signal keys: Program Program Button 1，Press the button, its LED light turns on，Program output will be switched to this channel 1; Program Button 2，Press the button, its LED light turns on，Program output will be switched to this channel 2; DVI3 input selection Button，its LED light turns on, Program output will be switched to this channel; DVI4 input selection Button，its LED light turns on, Program output will be switched to this channel; VGA3 input selection Button，its LED light turns on, Program output will be switched to this channel; VGA4 input selection Button，its LED light turns on, Program output will be switched to this channel; Preview Press the button, its LED light turns on，Preview output will be switched to this Program Channel 1; Press the button, its LED light turns on，Preview output will be switched to this Program Channel 2; VSP 5162 User’s Guide 34 2. Hardware Orientation VSP 5162 Front Panel DVI3 input selection Button，Press the button, its LED light turns on, Preview output will be switched to DVI3 channel; DVI4 input selection Button，its LED light turns on，its LED light turns on，Preview output will be switched to DVI4 channel； VGA3 input selection Button，its LED light turns on，its LED light turns on，Preview output will be switched to VGA3 channel； VGA4 input selection Button，its LED light turns on，its LED light turns on，Preview output will be switched to VGA 4 channel； Note Program out goes through the connector ，review output goes through the connector DVI2 goes through cable and VGA video, or use output VGA video. ，DVI+VGA output ，to output DVI adapter to Function BLK: The BLK button can be thought of as an additional input video source. When selected the BLK button LED light will turn on and the preview output will be black. Press TAKE Button，Program output will be black;Press again BLK button to disable BLK signal and video processor returns to original Preview output，Press TAKE，Program output the same picture of Preview output, Preview out is the former previewed input signal。 TP: Test Pattern，press this button, will output test pattern picture, test VSP 5162 User’s Guide 35 2. Hardware Orientation VSP 5162 Front Panel pattern can be set and selected from LCD panel, press the TP button again, to disable TP. Press SEL to enter TP setting menu，when enabled/disabled, shows TP is turned on/off. Press LEFT/RIGHT button，can output TP through DVI2 and VGA. Note TP is the picture of Color Bar at the resolution of 1024x768x60. Test pattern is used to check whether the output is OK without the inputs, and can use to qualify the output quality and display quality. Seamless dissolving, press the button to to switch preview out to Program Output with dissolving transition effect； Seamless cutting button, press the button to switch preview out to Program Output; Press the button to enter fade in fade out configuration menu, users can set the duration time of fade effect. VSP 5162 User’s Guide 36 2. Hardware Orientation VSP 5162 Front Panel Note CUT, FADE or TAKE, WIRE is what we mean fade in and fade out or switch with transition effect. Press the button to enter Effects Configuration Menu, mutiples effects are available, such as Wipe hard (soft), Wipe Plus out. Press the button to show picture in picture on the screen;press the button again to return single picture window. SCALE SIZE AND POSITION SETTING,Press the button and goes from HsizeVsizeHPOSVPOS to set Size value and position value; Program button，press to enter channel configuration; Advanced menu，Press the MENU to enter the main menu, the submenus: Device information, Factory Reset, Language and Alpha setting are all included. Push the LEFT/RIGHT to select the relevant submenu. Press the button to update system information; The function is same with Status under MENU. Output resolution selection button，Push OUT to enter the Output menu. Press the UP or DOWN to select different output resolution , Push SEL to select。 VSP 5162 User’s Guide 37 2. Hardware Orientation VSP 5162 Front Panel Parameter Recalling Button，Press LOAD to recall the saving parameters , users can load data from SAVE1 or SAVE2. Press the UP or DOWN to select modes SAVE1 or SAVE 2, Push SEL to confirm. Load Setting From： >SAVE1 SAVE2 Saving Button, press the button to save the parameters to SAVE1 or SAVE2. Press the UP or DOWN to select saving destination SAVE1 or SAVE 2, Push SEL to confirm. Save Setting From： >SAVE1 SAVE2 VSP 5162 User’s Guide 38 3. Hardware Installation In This Chapter This chapter provides comprehensive installation instruction for VSP 5162 hardware： Following is the size of VSP 5162 for your reference. VSP 5162 User’s Guide 39 Safety Precautions For all VSP 5162 processor installation procedures, please observe the following important safety and handling rules to avoid damage to yourself and the equipment. To protect users from electric shock, ensure that the chassis connects to earth via the ground wire provided in the AC power Cord. The AC Socket-outlet should be installed near the equipment and be easily accessible. Unpacking and Inspection Before opening VSP 5162 process shipping box, inspect it for damage. If you find any damage, notify the shipping carrier immediately for all claims adjustments. As you open the box, compare its contents against the packing slip. If you find any shortages, contact your sales representative. Once you have removed all the components from their packaging and checked that all the listed components are present, visually inspect the system to ensure there was no damage during shipping. If there is damage, notify the shipping carrier immediately for all claims adjustments. Site Preparation The environment in which you install your VSP 5162 should be clean, properly lit, free from static, and have adequate power, ventilation, and space for all components. VSP 5162 User’s Guide 40 4. Menu Orientation In This Chapter This chapter describes all VSP 5162 processor menus, including how they are accessed, the functions that are available, and descriptions of each menu tree (in block diagram format). The following topics are discussed: • PRG • WIPE • OUT • SCALE • MENU Status Reset Language Output Scale Advance Picture Matrix Time Date PTP Crop TP Color SDI VSP 5162 User’s Guide 41 4. Menu Orientation PRG PRG Input signal edit button, select input, press the key to edit, HDMI、DVI、 VGA、YPbPr，CVBS1，CVBS2，USB1，SDI1. Program guideline for Button 1, Button 2: Firstly: Press Preview Button 1or Button 2; Press buttoon; Thirdly, LCD panel will give message and ask users to select input source by pressing Press to confirm; Fourthly, Press buttons. to quit from program and finish. VSP 5162 User’s Guide 42 4. Menu Orientation WIPE WIPE Press the button to enter Effects Configuration Menu, mutiples effects are available, such as Wipe hard (soft), Wipe Plus out. VSP 5162 User’s Guide 43 4. Menu Orientation WIPE VSP 5162 User’s Guide 44 4. Menu Orientation OUT OUT Output resolution selection button，Push OUT to enter the Output menu. User can press UP/DOWN to choose different output format, VSP 5162 support 7 kinds of output resolution, specific as follows figure; VSP 5162 User’s Guide 45 4. Menu Orientation SCALE SCALE SCALE SIZE AND POSITION SETTING. Press SCALE to control scale, it can set the size and location of sub-image via PIP. Note Scale adjust program output, preview always keep full-screen. Push LEFT/RIGHT and push UP/DOWN and SEL to confirm the relevant items. User can change the digital screen setting parameters to change the screen size and position easily. This mainly used in the LED screens users. VSP 5162 User’s Guide 46 4. Menu Orientation MENU MENU Press the MENU to main menu, main menu as shown: press UP/DOWN buttons to select left or right menu item. * before the menu means it’s in selected state. Press SEL button to enter corresponding setting or view the menu, and the first line shows: VSP 5162. VSP 5162 User’s Guide 47 4. Menu Orientation MENU MENU---Status After select Status, press SEL can show related information such as input/output video signal, as Pictured above. Press 【UP】 or【DOWN】 to see the current preview input formats, output format, program version, and current equipment serial number. MENU---Reset If select Reset, press SEL to realize reset. After successful reset you will see the menu: Reset Finished, as pictured above: MENU--- Language Press 【ESC】to go back the main menu，Press 【UP】 or【DOWN】 to find LANGUAGE. Press 【SEL】 select the relevant submenu to LANGUAGE submenu. Press 【right】 and 【left】 to select the LCD language. MENU--- OUTPUT Press 【ESC】to go back the main menu. Press 【UP】 or【DOWN】 to find OUTPUT; Can set DE output signal and code format choice for DVI1 or DVI2 (optional HDMI or DVI). Select DVI1, Press【SEL】and enter the corresponding sub-menu settings, first enter the corresponding sub-menu to set DE switch; Press【ON】，and Press【SEL】to go to DE setting menu，Press【UP】 or【DOWN】to change the value. DE H Start: horizontal axis setting; DE V Start: vertical axis setting; DE Width: width setting; DE Height: height setting; When signal source appear large screen, and boundary appears black side, you can use this function to adjust it, and make the image to full screen. Select DVI1, press【SEL】, enter the HDMI/DVI settings for output signal; VSP 5162 User’s Guide 48 4. Menu Orientation MENU Interface is the default DVI output, choose HDMI when need HDMI signal output. Select DVI1, press SEL Light touch SEL can also be used to choose color format, you can choose the video format or image formats, colors range of video format is between 16-235, and colors range of image formats is between 0 - 255. The same method can be set to DVI2 output. MENU--- Scale Press 【ESC】to return to the previous menu，scrolling the menu，find the Scale menu. Press 【SEL】to enter the Scale setting, Scale menu means the zoom menu, including the following settings. Scale Width：Scale in horizontal. Scale Height：Scale in vertical. Position X：Scale X position. Position Y：Scale Y position. Note This setting can also achieve through Scale buttons. MENU--- Advance Press MENU to return to the main menu, scrolling to find Advance submenu; Press【UP】 or 【DOWN】 to set values for screen parameter and aspect ratio. Press 【SEL】，enter the advance menu, scrolling to find Screen: Screen Width：Set the horizontal size of the screen; Screen Height：Set the vertical size of the screen; Screen Pos X：Set the horizontal position of the screen; Screen Pos Y：Set the vertical position of the screen; Small Picture: Narrow the signal and the full screen switch. Press ESC, return to Advance menu, select others, press SEL to enter other settings, including such as above setting items. VSP 5162 User’s Guide 49 4. Menu Orientation MENU Polarity Select: you can choose Negative or Positive; Set the output timer polar, is usually effected when some unconventional sending card that does not recognize the output, Users need to set the positive and negative polarity of output timer. Sync Select: you can choose Internal, Preview, Program. Call Save Delay: Set delay the time for output; is usually used when at the same time multi-devices are powering up at the same time and the processor works as the rear end equipment, delay the time solve the problem of not recognizing the input input signal and LED screen appearing messy code or splash. Set USB playing duration for single picture, set this when needing to play for long time. Set the USB as video or picture mode, picture and video mode selected by the user, the USB can not play both pictures and video at the same time. Press ESC to return Advance settings, select PIP Mode, press SEL to set. Select Feature switch, and set the width when it is ON, including above settings; Feather function is mainly used in PIP, even if the edge of sub-image and main image get fusion effect. The bigger of Feather value is, the wider of the fusion range, and the smaller the Feather value is, the narrower the fusion range is. Users can adjust the size according to their need. MENU---Picture Press ESC to return to the main menu, scroll and find the submenu Picture 【Picture】. Press 【SEL】 to enter Picture setting，Picture menu includes parameters options for adjusting image quality. Set Brightness：To change the brightness value of image; Set Contrast：To change the contrast value of image; VSP 5162 User’s Guide 50 4. Menu Orientation MENU Set Sharpness：To change the sharpness value of image; Set Color Red ：To change the red color value of image; Set Color Green：To change the green color value of image; Set Color Blue：To change the blue color value of image; Users can adjust the settings according to the actual situation; is mainly applied to the technician who is very professional at the image quality. However, if there are any improper operation or image quality errors or distortion occurring, reset the device from main menu Recall. The numerical range needs to adjust between 0 to 100. MENU---Matrix Press 【MENU】，return to the main menu. Press【DOWN】 and set 【Matrix】. Press SEL button and enter Matrix setting, the menu includes the above settings. Matrix function: Can achieve copy in a channel for any other channel, which DVI1 output still can choose Preview or Color BAR output, in addition to the default Program output, and in addition to Preview output outside, DVI2 or VGA1 output can also choose Program or Color BAR output. MENU--- Time Press 【MENU】，return to the main menu. Press【SEL】to enter Time setting; Press【SEL】 to activate the Time setting, if there is a * sign, means the menu item has been selected; Use the knob from the front keyboard to revise the time. MENU--- Date Press 【MENU】，return to the main menu. Press【UP】 or 【DOWN】 to set Date; Press【SEL】to enter Date setting. Date shows on the left side，Day shows on the right side. Press 【SEL】 to activate the Calendar setting, if there is a * sign, means the menu item has been selected，Press VSP 5162 User’s Guide 51 4. Menu Orientation MENU 【UP】 or【DOWN】 to change the value. MENU---PTP Press 【MENU】，return to the main menu. Press【UP】 or 【DOWN】 to set 【PTP】 pixel-to-pixel mode. Press 【SEL】 to enter PTP pixel-to-pixel switch choose. Pixel-to-pixel mode requirements input interface DVI3 or DVI4 signal access, and pixel-to-pixel function only woks for DVI3 and DVI4 channel. MENU---Crop Press 【MENU】，return to the main menu. Press【UP】 or 【DOWN】 to set 【Crop】. Press 【SEL】 to enter CROP setting, Crop setting includes following submenu: Crop Width：Set the horizontal size; Crop Height：Set the vertical size; Crop Pos X：Set the horizontal position; Crop Pos Y：Set the vertical position; MENU---TP Color Press 【MENU】，return to the main menu. Press【UP】 or 【DOWN】 to find TP Colo. Press SEL button，select RGB, push UP/DOWN to set the value for Color RGB. MENU--- SDI Press 【MENU】，return to the main menu. Press【UP】 or 【DOWN】 to set 【SDI】. SDI supports with 3G-HD, SD SDI input. Note：When SDI is SD format, user needs to set from the LCD panel separately. VSP 5162 User’s Guide 52 5. Communication Software Guideline In This Chapter This chapter provides detailed information about the control communication software. The following topics are discussed: Install Software Run Software How to control processor through RS232? How to control processor with console software by USB? VSP 5162 User’s Guide 53 5. Communication Software Guideline Install Software Install Software AVDSP video processor is very easy to be configured with user friendly communication software, support drag and drop operation for edit and display. Also it can be customized with schedule function. Double click VSP 5162.exe to install, English version default for use, click “select” to next dialog: And in next dialog is the user agreement of the software, click Agree to go on: VSP 5162 User’s Guide 54 5. Communication Software Guideline Install Software User can select “Change” to choose the VSP 5162 install software: VSP 5162 User’s Guide 55 5. Communication Software Guideline Install Software Click “Next” to go on： Click “Next” to go on： Click “Next” to go on： VSP 5162 User’s Guide 56 5. Communication Software Guideline Install Software Click “Finish” and ready to run VSP 5162 console: VSP 5162 User’s Guide 57 5. Communication Software Guideline Run Software Run software Install communication which comes with the package of VSP 5162 device. Double click AVDSP.EXE icon from home screen to run the software. VSP 5162 communication software interface as shown： Set Up Communication When control video processor through PC software, besides the power cord, the product default equip with a line that is COM (RS-232), 9-pin (DB9F), RJ11 COM crystal head (6 B4C). Below are the details about connection of steps: First connect 9-pin (DB9F) to the computer on the corresponding port, and connect COM crystal to RS232 port on video processor. Open video processor; Next, operate the computer, back to computer desktop, right click【 My computer 】to【 Properties 】, find the【 Hardware 】option card, as follows, left click 【 Device manager 】: VSP 5162 User’s Guide 58 5. Communication Software Guideline Run Software Find 【 (COM and LPT) 】 port in 【 device manager 】, click the plus sign on the left, record serial interface name that computer provides, as following chart, the serial port is COM1. Confirm used COM and open control software, click 【communication】 page，enter setup option，Serial is the default COM，click icon to refresh COM number，choose available COM，default Baud rate is115200. VSP 5162 User’s Guide 59 5. Communication Software Guideline Run Software After serial setting, click icon，the icon becomes when successfully connected，on the left button showing , meaning has connected video processor through COM, and can control video processor through the PC software. For more detailed information, please refer to: “How to control processor through RS232？”. In addition, we also equipped with USB line, you can also connect the computer and video processor with it to control PC software. Please refer to “How to control processor with console software by USB?” for more detailed information. Note RS 232 COM line can upgrade 100M program, while USB can’t. Ethernet ，user can fill any number less than1023 in local port，the remote port must be 192.168.0.100 and the remote port must be 1000。After VSP 5162 User’s Guide 60 5. Communication Software Guideline Run Software setting above, click the icon to connect with the net work。If successful connect, the icon becomes showing ，status on the left button 。 Mode control Interface as following: Preview Left part is preview window, input signal information will be shown on the top left conner , such as signal types and its resolution, the button part’s button Corresponds with preview channel, color green tell button is selected. Preview image can be swathed by button, in order to preview the six channels. Programme Right part is programmed window, input signal information will be shown VSP 5162 User’s Guide 61 5. Communication Software Guideline Run Software on the top left corner , such as signal types and its resolution, the button part button corresponds with programmed channel , and programmed output image can be swathed by button ,also can drag and drop the image to adjust the size and position of the programmed output signal. Output resolution toolbar User can choose three output resolution by selecting from scrolling down list: Note Same with OUT function. Current config mode Mode 1 refers to single picture，Mode 2 refers to dual picture .（picture mode only works for program output，while preview output always keeps as single output）. Call saving modes VSP 5162 User’s Guide 62 5. Communication Software Guideline Run Software Click the buttons as followings to apply. FS Switch between the FULL screen mode and scaled screen mode; CUT Seamless cut button，will switch preview image to program output; Note Same with OUT function. Take Seamless transition effects button, will switch preview image to program output with special effects; Note Same with Take function. Effects Toolbar VSP 5162 User’s Guide 63 5. Communication Software Guideline Run Software The device not only provides the most common fade effects(in default), but also other fourteen seamless transition effects: wipe right ,wipe left ,wipe up, wipe down, wipe center out, wipe curtain out ,wipe square out etc. Note Same with WIPE function. Fade in and fade out toolbar Set the value for duration (0-30s) from progress toolbar. Note Same with FADE function. Fade duration Set the grades (0-16 grades) for switch speed. Width of transparent toolbar Set the pixels (0-255 pixels) for transparent; VSP 5162 User’s Guide 64 5. Communication Software Guideline Run Software Configuration Input setting Configure input information, can configure for input1, input2 separately： Input source choice Support CV, YPbPr, VGA, DVI，SDI, USB input sources. Select any single you need. Input resolution toolbar Shows the resolution of current input source. Display Offers 2 different display modes, when selected “live video “, video will be played normally, when selected “freeze” the display only shows the last frame. Ratio Choose 4:3 or16:9 from scrolling down list. VSP 5162 User’s Guide 65 5. Communication Software Guideline Run Software Output timer polar Set output timer polar, it is usually set if some unconventional sending card can not recognize output. Image Quality Setting Set the brightness, color temperature, contrast and saturation, sharpen of the image. Note Same with Picture function. Mode configuration VSP 5162 User’s Guide 66 5. Communication Software Guideline Run Software Image input toolbar VSP 5162 is a two-layer processor, the data of each layer can be set from this toolbar, and data can be input at any combination of two channels. That is what calls “matrix function”. Scale, Zoom, Crop can be realized by entering the value or rolling down the list, or drag and drop the picture. Operational mode selection Interface Single image mode VSP 5162 User’s Guide 67 5. Communication Software Guideline Run Software PTP (Pixel to Pixel)： Pixel-to-pixel mode requirements input interface DVI3 or DVI4 signal access, and pixel-to-pixel function only woks for DVI3 and DVI4 channel. PIP mode：Dual image mode VSP 5162 User’s Guide 68 5. Communication Software Guideline Run Software Test Pattern Signal： Used when users need to do effect testing for screen. Screen Parameters Before using the FS function so as to realize to switch between full screen mode and scaled image mode, please configure the screen parameters. VSP 5162 User’s Guide 69 5. Communication Software Guideline Run Software Set Click 【set】button each time to confirm the setting. Save Click 【save】to save all the revised parameters, the scrolling list indicated the location to be saved to, if successfully user can call it anytime in the future. Update reset Click this button to recall the factory setting. VSP 5162 User’s Guide 70 5. Communication Software Guideline Run Software Control Cascade control Used for multi devices stacking up to splice a large screen, please refer to the detail manual. Setting for Multi devices –VSP 5162 Cascade.ppt Setting for Multi devices –VSP 5162 Cascade.pps Or refer to Cascade of 6.0 System Setting and Operation in this guide. Input setting interface Set the input resolution and input source, as well as the display area for input. VSP 5162 User’s Guide 71 5. Communication Software Guideline Run Software Cascade function is effected only for DVI3 or DVI4. Output Settings interface To set output resolution and timing synchronization. When the Input/output resolution keeps the same, should select “Input Signal” as Sync Source. When different, should “select Internal”. VSP 5162 User’s Guide 72 5. Communication Software Guideline Run Software Splicing setting Save setting VSP 5162 User’s Guide 73 5. Communication Software Guideline Run Software Delay time Set delay the time for output; is usually used when at the same time multi-devices are powering up at the same time and the processor works as the rear end equipment, delay the time solve the problem of not recognizing the input input signal and LED screen appearing messy code or splash. This operation is similar to the advance on LCD, where users can find “Call Save Delay”. Note Same with MENU Advance Others Call Save Delay function. DVI DE DELAY Set the output timer polar, is usually effected when some unconventional sending card that does not recognize the output, Users need to set the positive and negative polarity of output timer. Set the output HS line and VS field polarity, is usually effected when some unconventional sending card does not recognize the output, user needs to set the positive and negative polarity of HS line and VS field. VSP 5162 User’s Guide 74 5. Communication Software Guideline Run Software Note Same with MENU Advance Others Polarity Select function. VGA input adjustment IP setting With the feature, the user can set the device’s IP himself, the function is generally used when the user wants to use the same computer to do simultaneous manipulation or remote control, if IP is changed through serial port, IP changes would take effect immediately, if IP is changed VSP 5162 User’s Guide 75 5. Communication Software Guideline Run Software through Ethernet port, user should close the control software and reopen it use the new IP to do the communication. Factory reset Click “factory setup”, previously saved user-mode will be cleared. Option Language Language choices: English and Chinese. Administration Advance option, for administrator control VSP 5162 User’s Guide 76 5. Communication Software Guideline Run Software Note “Advance” for engineer specially, please contact with our customer service engineer to get the code if it is necessary; Help Version notice Display the software version and what is new; About Display the software version and company information; Information toolbar The button line of the interface of control software shows the software version, main chip version, hardware version and SN. VSP 5162 User’s Guide 77 5. Communication Software Guideline How to control processor through RS232? How to control processor through RS232? Firstly，install the control software in your PC; Take out the RS 232 cable as following（RS-232, with 9-pin on one end， RJ 11 on the other side.） Connect one side of the RJ11 download line to the RS232 on the video processor VSP5162, and the other side to be connected to the serial port on the PC. If there is no any Serial port on your PC, you will need another Serial to USB adapter. Connect one end of the RJ11 download line to the RS232 on the video processor. Connect the end of USB-side to the PC, Ensure the cable connection is good. Turn on the Video Processor VSP 5162. Right click the【My Computer】on the home screen of control PC. Enter 【Attribute】, Find【Hardware】Option，as following. VSP 5162 User’s Guide 78 5. Communication Software Guideline How to control processor through RS232? Click【Device Manager】“+” on the left，check the COM number，as following， COM1 is offered. Remember the COM you are using and then run the control software, find 【Communication】 option. In default，first time user have to click button，as following: VSP 5162 User’s Guide 79 5. Communication Software Guideline How to control processor through RS232? Check and tap【Serial】，Serial Port , for example, is COM6 which is checked from device manager. Set VSP 5162 Boud Rate to be :115200， Click【Confirm】after setting. Click 【 open serial】，check if【COM】icon on the bottom right corner， when there is the prompt green showing on the software, it means the communication is ok , and you can use the software to control the device now. Note If power off during communication, should close the port , by first, and plug in out of the USB and do communication. VSP 5162 User’s Guide 80 5. Communication Software Control Guide How to control processor with console software by USB? How to control processor with console software by USB? Install the driver Connect the USB cable to the PC and the video processor .turn on the VSP 5162, for the first time to use USB, the PC will remind finding the new hardware and ask to install the driver for this new driver: Install from the list or specified location, press “NEXT”: Press “browser” to find the driver, and press “NEXT”: VSP 5162 User’s Guide 81 5. Communication Software Control Guide How to control processor with console software by USB? When the installation finish, can go to check the installed COM port inside the device management, as following picture shows: VSP 5162 User’s Guide 82 5. Communication Software Control Guide How to control processor with console software by USB? Install the console software, and run after install, shows the interface of the console as following: Select the COM as installed just now, and set the VSP 5162 Boud Rate to be: 115200. VSP 5162 User’s Guide 83 5. Communication Software Control Guide How to control processor with console software by USB? Press to start communication，when there is green point in the right down corner showing on the software, it means the communication is ok, and you can use the software to control the device now；the software operation is the same as VSP 5162. VSP 5162 User’s Guide 84 6. System Setup and Operations In This Chapter This chapter provides comprehensive instructions for system setup and operations. The following topics are discussed: Interface and Input Signal Option Single Picture Signal Switch PIP Setting USB Input Setting Csacade Setting VSP 5162 User’s Guide 85 6. System Setup and Operations Interface and Input Signal Option Interface and Input Single Option NO. INTERFACE NO. INTERFACE 1~4 CVBS input 11.12.22.23 Gigabit copper port 5.16.17.18 DVI input 13.24 Power Supply Port of Sending Card 6.19 VGA input 14.25 USB Control Port of Sending Card 7 Dial switch 15.26 DVI input 8 10/100M interface 20.21 DVI output 9 USB interface 27 Power and switch 10 RS232 interface Among them, 20. Program is priority screen output, mainly connect large screen sending card, and at present, VSP5162 support VESA：1024×768×60Hz， 1280×768×60Hz，1280×1024×60Hz， 1440×900×60Hz，1680×1050×60Hz，1600×1200×60Hz， 1920×1080×60Hz； Press 【OUT】 and scroll 【UP】 or 【DOWN】 to find corresponding output and press【SEL】 to confirm. 21. Preview is preview output interface, mainly preview the signal and image through the display preview that to output signal, the output signal is DVI video signal and VGA video signal that can connect with display with DVI interface or VGA interface, and other display device, through DVI-I interface output signal (Preview adopts standard DVI interface, VSP 5162 User’s Guide 86 6. System Setup and Operations Interface and Input Signal Option compatible VGA output, connect VGA output through the terminal.). Support the resolution: VESA：1024×768×60Hz； In addition to CONT, sending card and power interface, the other interfaces are video signal input interface, this interface can input including DVI、HDMI、VGA、YPbPr、YCbCr、CV、SDI signal. Key Operation of Signal Format Selection If channel 【1】 needs to choose VGA signal, first, choose Preview 【1】， then press 【PRG】to signal formats to select menu, scroll 【UP】 or 【DOWN】 to choose corresponding input formats. If need to select VGA, press 【SEL】 to confirm. Channel 【2】, if input composite signal, press 【2】 under Preview, then select CV via 【PRG】, and press【SEL】 to confirm. VSP 5162 User’s Guide 87 6. System Setup and Operations Single Picture Single Switch Single Picture Single Switch If it is just simple seamless effects switch between stage pictures, the settings above are basic completed, just save the existing information and master switch skills in practice, as follows: Button Save User Mode Operations Press 【SAVE】, can save the current parameters to user mode 1 or user mode 2, after reboot, device default user mode 1. Single Image Switch VSP5162 can realize seamless effects switch between two channels, only choose the channel that need to switch to big screen, such as [1] light under Program flash, means large screen output is channel 1 signal. Press [2] under Preview if need to switch the second channel signal to large screen, then through 【 CUT 】 seamless switch or 【 TAKE 】 seamless effects switching. 【 TAKE 】 general default for 3 seconds as fade effects duration, if need to adjust the time, press 【 FADE 】 then scroll 【UP】 or 【DOWN】 or 【LEFT】 or 【RIGHT】 to modify the corresponding time, press 【 SEL 】 to confirm. Press 【 TAKE 】again, can switch the adjusted fade duration in the second channel to large screen. If need to switch to other channels signal, just press the corresponding channel under Preview, then press 【 CUT 】 or 【 TAKE 】 to switch. VSP 5162 User’s Guide 88 6. System Setup and Operations Single Picture Single Switch Blackburst Switch VSP5162 design a shortcut key to black output, press Program 【 BLK 】, and swith blackburst through 【 CUT 】 or 【 TAKE 】 slowly turning black, screen turn to blackburst, again press 【 CUT 】 or 【 TAKE 】, image restore display. Scale Maybe the image’s size and position that need to output are not quite the same for different channel, VSP5162 can realize the adjustment for the image’s size and position of different channel separately. By pressing corresponding signal button under Preview and choose corresponding signal, such as choose 【2】, then press 【SCALE】 to the zoom function, there are four parameters, respectively for screen Width, screen Height, level starting position Pos X, vertical starting position Pos Y. Please scroll 【UP】 or 【DOWN】or 【LEFT】 or 【RIGHT】 to choose corresponding parameters and modify parameter according to screen demand, then press 【 SEL 】to confirm, and achieve different picture size and position settings. VSP 5162 User’s Guide 89 6. System Setup and Operations PIP Setting PIP Setting VSP5162 【PIP】button can realize seamless switch of dual image mode and single image mode. VSP5162 can at most output any position and any size of signal from 2 channels to the screen. Program column signal key under dual pictures control the signal choice of first layer. Preview control the second layer signal options, so the screen can show the most two exactly same picture, specific operation as follows: Each Image Width, Heigh and Position Setting Press 【PIP】is mutil images switch, in which, the program outputs the main image，preview monitor shows the sub-image. Press Program buttons to switch to targeted main image. Press Preview buttons to switch to targeted sub-image. Set the size and position of the PIP image: To set the size of sub-image， firstly, Press the targeted button in Preview area. Secondly, Press SCALE button. Thirdly, according to the message that LCD shows, Press LEFT/RIGHT, select and adjust the size and position. There are four parameters, respectively for picture Width, Height, level starting position Pos X, vertical starting position Pos Y, please choose corresponding parameters VSP 5162 through 【 LEFT 】 and 【 RIGHT 】 User’s Guide 90 6. System Setup and Operations PIP Setting according to the pictures show and modify parameter through 【 UP 】 or 【 DOWN 】, and then press 【 SEL 】 to confirm. Set and save. The same operation can be applied to Main Image adjustment. If need to switch back to single image mode, please press 【PIP】again, the button turns off LED. Console Software Setting Each Image's Width, Heigh and Position Firstly: Click configuration page, click “Config”, Click “ PIP”. Secondly: Set the size and position of layer1 and layer2. Thirdly, click “mode”，and switch it back to smaller image’s channel, click Preview Screen and switch back to bigger image’ channel, Click Program Screen to finish. VSP 5162 User’s Guide 91 6. System Setup and Operations USB Input Setting USB Input Setting Keyboard operation Make sure USB source is connected: Firstly，Press button 1 or button2 in the preview lines, take button 1 as example; Secondly, press【PRG】; Thirdly, the LCD will give the message as following; Program source >DVI1 1： Press UP/DOWN to select USB1，press 【SEL】，the device will read USB file as well as playing list automatically. Program source >USB1 1： Note: Some USB file can not be identified, maybe it is likely due to the problem USB itself, or due to the file that can not be support ed (check the file format: Image format should be :JPGE, BMP,PGN; video format: MPEG1, MPEG2, MP4, RMVB, MJPG.) or because of loose connection (USB disk needs to be inserted again). Press LEFT/RIGHT，to pause the USB video play. Press UP/DOWN, to select USB video source. VSP 5162 User’s Guide 92 6. System Setup and Operations USB Input Setting Console software operation Firstly, make sure USB source is connected; Secondly, Click ”Config”, and select the USB1 as shown above; Thirdly, Click the USB window on the right side where users can select the USB image or video source, as well as to set the playing duration, playing progress. VSP 5162 User’s Guide 93 6. System Setup and Operations Cascade Setting Cascade Setting Not only can VSP5162 processor single machine realize at most 17 signals six channel seamless switch, meet the stage acting effect your demand; Its multi device cascade synchronization seamless switching solutions, is super large stage acting perfect. Press 【 PIP 】 can realize the seamless switch of dual pictures and single picture. Basic Working Principle VSP5162 multi signal seamless processor can realize at most six channel enlarge or minification separately, any channel seamless switching, which made the processor meet the super screen cascade each card display part play function, this is prerequisites for super screen cascade. On this basis, VSP5162 also realize external timing synchronization, that is when VSP5162 multi device cascade, can adopt the front end advice timing, so ensure the image’s timing synchronization and color consistency. The working principle of VSP5162 multi device cascade is assigned the front signal to corresponding VSP5162 processor, again synchronous external timing through processor, and whole enlarge picture and intercept corresponding display area according to the corresponding control area to achieve the function of integral display a complete picture, through the central control, or computer, it can realize the synchronous broadcasting and at the same time switch seamlessly. For central control, we will provide the common functions of ASCII command set of VSP5162 in attachment. VSP 5162 User’s Guide 94 6. System Setup and Operations Cascade Setting Simple Structure Connect Guide Take each simple processor of their individual show a picture and all the processor combined to show a complete DVI picture and realize the synchronous switch for example. As above, can assign one way DVI single to DVI matrix or distributor, of course, if large screen overall picture would switch by a few ways signal, DVI matrix or distributor front can also increase a VSP5162 for the whole signal switch; DVI distributor will assign signal to the corresponding video processor area that VSP5162 input DVI3 (or DVI4). If hope to achieve multiple areas show the same picture, you assign the single through the corresponding distribution, and received the corresponding processor. Finally assign the signal to the corresponding to sending card by processor. Set display Parameters for Each Processor Each Input and Save In the project, the processor is just as part to show the corresponding part of the picture, similar to every case of the LED screen, we have two settings ways to achieve processor refresh connections: one is the same VSP 5162 User’s Guide 95 6. System Setup and Operations Cascade Setting with sending card set display connection mode, it incorporate all the processor into a LAN and through the control software to realize the whole set; The other is setting each processor parameters individually and save. This section mainly introduces each VSP5162 parameter setting and calculation when multi processors display a whole picture, we suggest users try to use computer control software to set: Step 1: Open and connected PC software through USB or COM connect processor. Step 2: Set output resolution under the control mode, as follows: Picture1 Step 3: Select corresponding signal input, such as if need to install DVI3, make sure choose DVI3 for the main output and monitor output for DVI3 choice, as follows: Step 4: Set the narrowing of the corresponding channel, switch tab to "configuration". Then set corresponding narrow and cut out according to the processor area and display size. VSP 5162 User’s Guide 96 6. System Setup and Operations Cascade Setting Assume large scree is 3536*768, through 3 or so VSP5162 processor control the screen of 1000 * 768, central control 1536 * 768, then setting calculation for each device scale and cutting parameter is as follows: First set scale, for around two processors, each card’s starting position is (0, 0), each screen is 1000 * 768, so scale setting of the two processors are: This is based on the screen of sending tapes, the second screen is bigger, up to 1536 * 768, so first set output higher than 1680 * 1050 resolution, and then down to (0,0,1536,768). Then all sending tape screens are alone full-screen display the same signal picture, as follows: For screen cascade between different space, it also can cascade by adjusting picture narrow "height"of different processor. The adjust each processor DVI3 cut out, you can see from the above picture that need to amplified the whole picture to the whole screen and cut the corresponding area to corresponding sending card. The default VSP 5162 User’s Guide 97 6. System Setup and Operations Cascade Setting cutting parameters indicate the input signal resolution is 1280 * 720, that turn the width of 1280 to full whole 3536, then left 1000 indicate 1280’s 362 points（=1000/3536 *1280） The same algorithm, middle 1536 shows 1280 from 362 points to 556 points（=1536/3536 *1280） The third device shows 362 points back of 1280. All above operations need to press "Settings" to change, and save after modify, as follows: VSP 5162 User’s Guide 98 6. System Setup and Operations Cascade Setting Central Control Setting Guide All the processors have a control serial port, it can realize the real time control via control computer, control table or central. The introduction of central control, through its own multi serial ports, can achieve one-button control all processor to realize synchronization seamless switch. For all synchronous switch, the simple solution is adding a TAKE command for each serial to realize fade duration (or CUT directly switch), key variables of central control correspond to all these serial variables. VSP 5162 User’s Guide 99 6. System Setup and Operations Cascade Setting As shown, the left is central control key variables, and right is variables of two corresponding serial port and corresponding ASCII command, all TAKE and CUT command of VSP5162 are two codes. After TAKE command of the central control, central control will also perform all the serial port TAKE orders, so is CUT, so you can add different command according to your need. If to achieve single device control, just add different variables for central control, and set corresponding serial variables and ASCII code separately, as follows, single device control can be realized. VSP 5162 User’s Guide 100 6. System Setup and Operations Cascade Setting VSP5162 Common Serial Command Set (Serial Protocol) Baud rate 115200bps；1bit start bit；1bit stop bit；No parity. Note: TAKE following is fade duration switch commands, including two commands, and includes the brackets "< >" for start-stop, also CUT command can instead of realize switch directly < T0002903e000000d0 > 1. Select SDI as input 1 and take to the program output <T010472000700007e>（select SDI） <T00029036010000c9>（preview and take to input 1） <T0005903e000000d3> <T0002902a000000bc>（take to the program output via TAKE） Select single as input 1 <T0100720001000074>（select CV1） <T010572000200007a>（select CV2） <T010172000600007a>（select DVI1） <T010272000500007a>（select VGA1） 2. Select CV3 as input 2 and take to home screen. <T0203720001000078>（select CV3） <T00049036010100cc>（Preview and take to input 2） <T0005903e000000d3> <T0002902a000000bc>（take to the program output via TAKE） Select single as input 1 <T0200720002000076>（select CV4） <T020572000600007f>（select DVI2） <T0200720005000079>（select VGA2） 3. Select DVI3 as input 3 and take to home screen. <T00019036010200ca>（Preview select DVI3） <T0005903e000000d3> <T0002902a000000bc>（take to the program VSP 5162 User’s Guide 101 6. System Setup and Operations Cascade Setting output via TAKE） 4. Select DVI4 as input 4 and take to home screen. <T00039036010300cd>（Preview select DVI4） <T0005903e000000d3> <T0002902a000000bc>（take to the program output via TAKE） 5. Select VGA3 as input 5 and take to home screen. <T00049036010400cf>（Preview select VGA3） <T0005903e000000d3> <T0002902a000000bc>（take to the program output via TAKE） 6. Select VGA4 as input 6 and take to home screen. <T00059036010500d1>（Preview select VGA4） <T0005903e000000d3> <T0002902a000000bc>（take to the program output via TAKE） 7. Large screen takes to blackburst <T00009036010600cd>（Preview select VGA3） 8. Save on call <T0002680901000074>，user mode 1 <T0003680902000076>，user mode 2 <T0004680903000078>，user mode 3 <T000568090400007a>，user mode 4 VSP 5162 User’s Guide 102 7. Common Questions and Solution In This Chapter This chapter provides the common questions and solution for the video processor. The following topics are provided: No Output in Large Screen Large Screen Output Flash Point Large Screen only Display Part of the Image No Display in the Second Half Part of Large Screen Large Screen Shaking Left of the Screen Appears Two Black Sides All Key Lights Light Simultaneously VSP 5162 User’s Guide 103 No Output in Large Screen Confirm if there are any input singles Press 【MENU】to find "Device information" , check if the INPUT signal is normal via 【 SEL 】, if suggest "NO INPUT", means no signal. Check the front-end signal line, please note do double show or expand for computer. Can enter other formats signal to do the same operation. Confirm if single output Find a belt VGA input (best for DVI) display, connect to the corresponding output port of processor, check whether the signal is correct on the monitor. If not display properly, please check whether there is input signal, or if input wire interface is taken tight, output wire interface is picked up tightly. If display normally, check if sending card is normally working or need to replace sending card test. Large Screen Output Flash Point Confirm if monitor output is normal Find a belt VGA input (best for DVI) display, connect to the corresponding outpur port of processor, check whether the signal is correct on the monitor. If display normally shows and no flash point, please check whether DVI outlets put tight or replace to DVI line of sending card. If display flash point, please judge if input signal, wire, and interface is normal. VSP 5162 User’s Guide 104 Large Screen only Display Part of the Image Signal need to scale Press 【SCALE】, adjust the size of screen size via left button, including "Width", "Height", and "Starting position", etc. Press【SEL】to confirm. No Display in the Second Half Part of Large Screen Resolution is inadequate Confirm the wide and high points on the screen, and select more adequater resolution than screen width. Press 【SEL】 to confirm. Sending card can't take lower part TS 802 can control the max horizontal resolution 2048, and vertical resolution 640. Each CAT5 output is 320 pixels. Large Screen Shaking Sending card input recognition is not correct It usually occurs in DBStar sending card. Use it’s normal before, but screen sway after change output resolution. It will be normal if re-open the sending card. VSP 5162 User’s Guide 105 Left of the Screen Appears Two Black Sides Adjust DE deviation This needs to adjust processor DVI output DE migration, find "Output" and find corresponding output name through the 【MENU】, such as "Output DVI1" and so on. Find "XY_POS" and adjust for corresponding horizontal and vertical DE. Please remember to save in the corresponding channel after set up, it is default save to SAVE1. Adjust each output offset value Cascade, and adjust each output’s offset value, find corresponding output position parameter setting, modify VSP330 in "Location". Press 【HDMI1】 -【HDMI4】 to find "XY position" and add 4. All Key Lights Light Simultaneously Check if dial switches are normal Shut the power, check if two red dial switches near CV are upward. Reboot if they face down, and reboot. The function of the red dial switched is mainly upgrade. VSP 5162 User’s Guide 106 A. Specification CVBS Input Number of Inputs 4 Connector Standard BNC Socket Supported Standard PAL/NTSC Signal 1Vpp±3db Supported Resolution 480i,576i (0.7V Video+0.3v Sync ) 75 ohm VGA Input Number of Inputs 4 Connector Standard DB9 Socket X2+ Standard DVI-I Socket X2 Standards VGA-UXGA Signal Level R、G、B、Hsync、Vsync:0 to1Vpp±3dB ohm black level：300mV Sync-tip：0V Supported Resolution VGA-UXGA (800*[email protected], 1024*[email protected], 1280*[email protected], 1440*[email protected],1600*[email protected]) (0.7V Video+0.3v Sync ) 75 DVI input Number of Inputs 4 Connector Standard DVI-I socket Supported Standard SMPTE：625/25/50 PAL, 525/29.97/59.94 NTSC, 1080P50,1080P59.94/60,1080i50,1080i59.94/60, 720p50,720p59.94/60 VESA：800×600×60Hz，1024×768×60Hz，1280×768×60Hz， 1280×1024×60Hz，1600×1200×60Hz，1920×1080×60Hz Signal Level TMDS pwl,single pixel input,165MHz bandwidth Standards HDMI 1.3 Signal level TMDS pwl , 165MHz bandwidth USB Input Number of Inputs 2 Connector Standard USB socket Standards Picture format: JPGE,BMP,PGN Video format: MP4, MPEG1, MPEG2, RMVB, MJPG. SDI Input(3G module) Number of Inputs 1 Connector Standard BNC Socket Transmission speed 19.4Mbps~3Gbps Supported ITU-R BT.656,ITU-R BT.601,SMPTE 259M, SMPTE 292, SMPTE VSP 5162 User’s Guide 107 Standard 297 Balance Belden 1694A 100m self-adaptive 1.485G,350m self-adaptive 270Mbps Signal Level TMDS pwl , 165MHz bandwidth 3G,200m self-adaptive YPbPr Input Number of Inputs 2 Connector Standard DVI-I socket Format Standard HD analog input Signal Level Y:1Vpp±3dB 75 ohm Supported Resolution 480i,576i,480p,576p,720p50,720p60,1080i50,1080p50 1080i60,1080p60 (0.7V Video+0.3v Sync ) 75 ohm Pb/Pr:0.7Vpp±3dB VGA Output Number of Inputs 1 Connector Standard DVI-I socket Supported Resolution VESA： 1024×768×60Hz，1280×768×60Hz， 1440×900×60Hz， 1680×1050×60Hz，1600×1200×60Hz，1920×1080×60Hz Signal Level R、G、B、Hsync、Vsync:0 to1Vpp±3dB ohm black level：300mV Sync-tip：0V (0.7V Video+0.3v Sync ) 75 DVI Output Number of Inputs 2 Connector Standard DVI-I socket Signal Level TMDS pwl, single pixel input, 165MHz bandwidth Supported Resolution VESA： 1024×768×60Hz，1280×768×60Hz， 1440×900×60Hz， 1680×1050×60Hz，1600×1200×60Hz，1920×1080×60Hz Function Input channel configuration support each input channel signal programming configuration PIP Support PIP、PBP for any two inputs Transition effects Fade in and fade out switching between any two inputs Extras Communication RS232 Power Supply 85-264V 2.1A IEC-3 Work Environment 0°C~45°C Stored Environment 10% to 90% Product Warranty 1 year VSP 5162 USB TCP/IP User’s Guide 108 B. Contact Information Warranty: RGBlink Science & Technology Co., Ltd policy is 1 year warranty and 3-year labor warranty since delivery day for the main components (basic motherboard, internal power supply, keyboard, LCD module, SDI input module, HDMI input module, audio input module, cascade output module, sending card, HDMI output module, SDI output module, analog video output module, audio output module, etc.). Within the guaranteed maintenance period, customers can send back the products if malfunction, and freight users from themselves. Users have the obligation to record the failure reasons if products malfunction. It does not belong to the warranty scope for any following circumstances, but can charge maintenance: 1) No 3 packets of proves and valid invoice. 2) The warranty vouchers have altered, the serial number of warranty and products of in-kind goods or altered identification inconsistent, or replacement. 3) The damage caused by user's use, operation, maintenance, keep improper. 4) The damage caused by non-our-company authorized service personnel or assigned service provider overhaul, or open without authorization. 5) The damage caused by force majeure (such as lightning, voltage instability). 6) Premium services that RGBlink set. Headquarter: S603~604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C. VSP 5162 User’s Guide 109 C. Upgrading Software How to upgrade VSP 5162 firmware? 1. First, connect the device with PC by network cable; 2. Input VSP 5162 network address in address toolbar: 192.168.0.100, enter the user name admin and password rgblink123 in the dialog box. 3. Thirdly, click on FPGA Upgrade; VSP 5162 User’s Guide 110 4. Fourthly, click on【browse】to select upgrade, file name must be Preamp_FPGA.bin or Bakamp_FPGA.bin； 5. Click 【Send】to send and wait for upgrade; 6. Upgrade Bakamp FPGA Success. VSP 5162 User’s Guide 111 Download the IP software Turn off the power, take the two coding switch to “ON” state as below: Connect one side of the RJ11 download line to the RS232 on the video processor, and the other side being connected to the serial port on the PC. Double click to run flash magic, setting as below: Firstly, users can choose the right serial port, set the Boud rate to 9600, choose LPC2368, and to load the aim document (hex file) for IP board upgrading; Secondly, confirm the two option box by check. Finally, click the “start” button. VSP 5162 User’s Guide 112 After download, exit the program, turn off the power, tack the two coding switch back, as below restart the equipment power, check if the equipment work normally. Note Flash Magic download website: http://www.flashmagictool.com/download.html&d =FlashMagic.exe VSP 5162 User’s Guide 113
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021