User manual | 48p9760

xSeries 440
򔻐򗗠򙳰
Option Installation Guide
SC48-P976-00
Note: Before using this information and the product it supports, be sure to read the general information in “Notices” on page 57.
First Edition (April 2002)
© Copyright International Business Machines Corporation 2002. All rights reserved.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.
Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Chapter 1. Introduction . . . . . . . . . . .
Major components of the xSeries 440 . . . . . .
Center plane connectors and LEDs . . . . . .
SMP Expansion Module connectors and lights . .
PCI-X planar internal connectors and LEDs . . .
I/O board internal connectors . . . . . . . .
Remote Supervisor Adapter component locations.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1
2
3
4
6
7
7
Chapter 2. Installing options. . . . . . . . . .
Before you begin . . . . . . . . . . . . . .
Working inside a server with power on. . . . . . .
Handling static-sensitive devices . . . . . . . .
System reliability considerations . . . . . . . .
Safety Information. . . . . . . . . . . . . .
Opening the cover . . . . . . . . . . . . .
Removing and replacing the bezel . . . . . . .
Removing and replacing a hot-swap power supply . .
PCI and PCI-X adapters . . . . . . . . . . .
PCI and PCI-X adapter considerations . . . . .
Installing adapters. . . . . . . . . . . . .
Cabling a ServeRAID adapter . . . . . . . .
Installing or replacing a drive . . . . . . . . . .
Hot-swap hard disk drive . . . . . . . . . .
Diskette drive . . . . . . . . . . . . . .
CD-ROM or DVD-ROM drive . . . . . . . . .
SMP Expansion Module . . . . . . . . . . .
Removing an SMP Expansion Module and cover .
DIMMs . . . . . . . . . . . . . . . . .
Installing and replacing a microprocessor . . . .
Reinstalling an SMP Expansion Module and cover .
Replacing and troubleshooting fans . . . . . . .
Replacing fans 1 and 2 . . . . . . . . . . .
Replacing fans 3 and 4 . . . . . . . . . . .
Replacing the battery . . . . . . . . . . . .
Closing the cover . . . . . . . . . . . . . .
Cabling the server. . . . . . . . . . . . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . 9
. . 9
. . 9
. . 10
. . 10
. . 14
. . 16
. . 16
. . 17
. . 19
. . 20
. . 20
. . 22
. . 24
. . 24
. . 25
. . 26
. . 27
. . 28
. . 31
. . 36
. . 41
. . 44
. . 44
. . 45
. . 47
. . 49
. . 50
Chapter 3. I/O connectors and indicators .
I/O connectors and indicators on your server .
Universal Serial Bus ports . . . . . . .
Keyboard connector . . . . . . . . .
Video connector . . . . . . . . . .
Auxiliary-device (pointing device) connector
RXE Expansion Port . . . . . . . . .
SMP Expansion Port . . . . . . . . .
Remote Supervisor Adapter communication
Gigabit Ethernet port . . . . . . . . .
Configuring the Gigabit Ethernet controller .
High-performance Ethernet modes. . . .
Ethernet port connector. . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
© Copyright IBM Corp. 2002
. .
. .
. .
. .
. .
. .
. .
. .
ports
. .
. .
. .
. .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
51
51
52
52
52
53
53
53
53
54
55
56
56
iii
Appendix. Notices
Edition notice . .
Trademarks . . .
Important notes. .
Power cords . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
57
57
58
58
59
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
iv
xSeries 440: Option Installation Guide
Safety
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d’installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto, leia as Informações sobre Segurança.
© Copyright IBM Corp. 2002
v
Antes de instalar este producto lea la información de seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten.
Statement 1:
DANGER
Electrical current from power, telephone, and communication cables is
hazardous. To avoid a shock hazard:
v Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical
storm.
v Connect all power cords to a properly wired and grounded electrical
outlet.
v Connect to properly wired outlets any equipment that will be attached to
this product.
v When possible, use one hand only to connect or disconnect signal
cables.
v Never turn on any equipment when there is evidence of fire, water, or
structural damage.
v Disconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
v Connect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached
devices.
To connect:
To disconnect:
1. Turn everything OFF.
1. Turn everything OFF.
2. First, attach all cables to devices.
2. First, remove power cords from outlet.
3. Attach signal cables to connectors.
3. Remove signal cables from connectors.
4. Attach power cords to outlet.
4. Remove all cables from devices.
5. Turn device ON.
vi
xSeries 440: Option Installation Guide
Statement 2:
CAUTION:
When replacing the lithium battery, use only IBM Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system has
a module containing a lithium battery, replace it only with the same module
type made by the same manufacturer. The battery contains lithium and can
explode if not properly used, handled, or disposed of.
Do not:
v Throw or immerse into water.
v Heat to more than 100° C (212° F)
v Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
Statement 3:
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
v Do not remove the covers. Removing the covers of the laser product could
result in exposure to hazardous laser radiation. There are no serviceable
parts inside the device.
v Use of controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.
Class 1 Laser Product
Laser Klasse 1
Laser Klass 1
Luokan 1 Laserlaite
Appareil A` Laser de Classe 1
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser
diode. Note the following.
Laser radiation when open. Do not stare into the beam, do not view directly
with optical instruments, and avoid direct exposure to the beam.
Safety
vii
Statement 4:
≥18 kg (39.7 lbs)
≥32 kg (70.5 lbs)
≥55 kg (121.2 lbs)
CAUTION:
Use safe practices when lifting.
Statement 5:
CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current
from the device, ensure that all power cords are disconnected from the power
source.
2
1
viii
xSeries 440: Option Installation Guide
Statement 8:
CAUTION:
Never remove the cover on a power supply or any part that has the following
label attached.
Hazardous voltage, current, and energy levels are present inside any
component that has this label attached. There are no serviceable parts inside
these components. If you suspect a problem with one of these parts, contact
a service technician.
Safety
ix
x
xSeries 440: Option Installation Guide
Chapter 1. Introduction
There are many optional devices supported by your server. This Option Installation
Guide provides the information needed to install, remove, and connect optional
devices supported by your server.
In addition to this Option Installation Guide, the following xSeries 440
documentation is provided with your server:
v Installation Guide
This printed publication contains setup and installation instructions. This
publication is also provided in Portable Document Format (PDF) format on the
IBM® xSeries Documentation CD.
v Rack Installation Instructions
This printed publication contains the instructions needed to install your server in
a rack. This publication is also provided in PDF format on the IBM xSeries
Documentation CD.
v Safety Book
This multilingual publication is provided in PDF format on the IBM xSeries
Documentation CD. It contains translated versions of the caution and danger
statements that appear in the documentation for your server. Each caution and
danger statement has an assigned number, which you can use to locate the
corresponding statement in your native language.
v User’s Guide
This publication is provided in PDF format on the IBM xSeries Documentation
CD. It contains general information about your server.
v Troubleshooting Guide
This publication is provided in PDF format on the IBM xSeries Documentation
CD. It contains the information needed to help you solve problems yourself, or
provide helpful information to a service technician.
Depending on your server model, additional publications might be included on the
IBM xSeries Documentation CD.
© Copyright IBM Corp. 2002
1
Major components of the xSeries 440
The following illustration shows the locations of major components in your server.
Note: The illustrations in this document might differ slightly from your hardware.
Shipping bracket
DIMM
access
doors
SMP baffle
Fan 4
Heat-sink
Fan 3
Cover
Microprocessor
SMP
Expansion
Module
DIMM
Fan 2
Fan 1
:
E
T
O
N
R
O
F
R
E
P
O
R
P
LO
F
IR
A
,
W
E
C
LA
P
E
R
N
FA
LO
F
IR
A
S
E
T
U
IN
M
X
O
B
2
F
O
R
E
P
O
R
P
IN
H
IT
W
R
O
F
T
N
O
R
F
:
E
T
O
N
,
W
E
C
LA
P
E
R
N
FA
S
E
T
U
IN
M
X
O
B
2
F
O
IN
H
IT
W
T
N
O
R
F
VRM
Center
plane
EMC Shield
(For single SMP Module)
Thumbscrews
Shipping thumbscrews
Hard disk
drive
Bezel
Hot-swap
power supply
CD-ROM
drive
2
xSeries 440: Option Installation Guide
Center plane connectors and LEDs
The following illustrations identify the connectors and LEDs on the center plane.
This center plane is used to connect the power and signal paths for the SMP
Expansion Module, I/O board, and the Remote Supervisor Adapter.
Media power
VRM
SCSI
power
Power
Power
Power
Thumbscrews
Chapter 1. Introduction
3
SMP Expansion Module connectors and lights
The following illustrations identify the connectors, switches, and lights on the SMP
Expansion Module.
4
xSeries 440: Option Installation Guide
SMP Expansion Module
board error LED
VRM error LED
Light path capacitor
switch LED
DIMM error
LED (16X)
Memory port 2
power LED
Hot-plug enabled
memory LED
Memory port 1
power LED
VRM error LED
Microprocessor 1
VRM error LED
Microprocessor 1
error LED
Microprocessor 3
error LED
Microprocessor 3
VRM error LED
Microprocessor 4
VRM error LED
Microprocessor 4
error LED
Microprocessor 2
error LED
Microprocessor 2
VRM error LED
Chapter 1. Introduction
5
PCI-X planar internal connectors and LEDs
The following illustration identifies the internal connectors and LEDs on the PCI-X
planar. This planar enables you to install adapters in the server.
6
xSeries 440: Option Installation Guide
I/O board internal connectors
The following illustration identifies the internal connectors on the I/O board. This
board supports the input and output ports located on the server.
Riser card
connector
SCSI B
connector
I/O VRM
Fan 4
connector
Fan 3
connector
Fans 1 and 2
connectors
Power/Reset
connector
USB cable
connector
Media bays
connector
SCSI A
connector
Remote Supervisor Adapter component locations
The following illustration identifies the connectors and lights on the Remote
Supervisor Adapter.
Lithium
battery
Ethernet speed
LED (green)
External power
supply connector
Error LED
(amber)
System board
connector
(J5)
Ethernet link
LED (green)
P- P
Power LED
(green)
Serial port Ethernet port
(RJ-45)
(COM)
ASM Interconnect port
(RJ-14)
Chapter 1. Introduction
7
8
xSeries 440: Option Installation Guide
Chapter 2. Installing options
This chapter provides instructions to help you install options in your server. Some
option-removal instructions are provided in case you need to remove one option to
install another. For a list of supported options for your server, see the
ServerProven® list at http://www.ibm.com/pc/compat/.
Before you begin
Before you begin to install options in your server, read the following information:
v Become familiar with the information in “Handling static-sensitive devices” on
page 10 and the safety guidelines provided in the “Safety Information” on
page 11. These guidelines will help you work safely with your server or options.
v Make sure that you have an adequate number of properly grounded electrical
outlets for your server, monitor, and any other options that you intend to install.
v Back up all important data before you make changes to the hard disk drives.
Working inside a server with power on
Your server supports hot-swap devices and is designed to operate safely while
turned on with the cover removed. Follow these guidelines when you work inside a
server that is turned on:
v Avoid loose-fitting clothing on your forearms. Button long-sleeved shirts before
working inside the server; do not wear cuff links while you are working inside the
server.
v Do not allow your necktie or scarf to hang inside the server.
v Remove jewelry, such as bracelets, rings, necklaces, and loose-fitting wrist
watches.
v Remove items from your shirt pocket (such as pens or pencils) that could fall into
the server as you lean over it.
v Take care to avoid dropping any metallic objects, such as paper clips, hair pins,
or screws, into the server.
© Copyright IBM Corp. 2002
9
Handling static-sensitive devices
Attention: Static electricity can damage electronic devices and your system. To
avoid damage, keep static-sensitive devices in their static-protective package until
you are ready to install them.
To reduce the possibility of electrostatic discharge, observe the following
precautions:
v Limit your movement. Movement can cause static electricity to build up around
you.
v Handle the device carefully, holding it by its edges or its frame.
v Do not touch solder joints, pins, or exposed printed circuitry.
v Do not leave the device where others can handle and possibly damage the
device.
v While the device is still in its anti-static package, touch it to an unpainted metal
part of the system unit for at least 2 seconds. (This drains static electricity from
the package and from your body.)
v Remove the device from its package and install it directly into your system unit
without setting it down. If it is necessary to set the device down, place it in its
static-protective package. Do not place the device on your system unit cover or
on a metal table.
v Take additional care when handling devices during cold weather because heating
reduces indoor humidity and increases static electricity.
System reliability considerations
To help ensure proper cooling and system reliability, make sure that:
v Each of the drive bays has either a drive or a filler panel installed.
v There is space around the server to allow the cooling system to work properly.
v Cables for optional adapters are routed according to the instructions that are
provided with the adapters.
v All microprocessors are the same size and clock speed.
v When two SMP Expansion modules are installed, they are connected together
through the SMP Expansion Ports.
v An SMP baffle is installed on top of the lower SMP Expansion module when only
one module is installed.
v For proper cooling, do not leave the cover open for more than 30 minutes.
v A failed fan is replaced within 48 hours.
v The top cover is closed during normal operation.
v Do not remove a defective power supply until a replacement is available.
10
xSeries 440: Option Installation Guide
Safety Information
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d’installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto, leia as Informações sobre Segurança.
Antes de instalar este producto lea la información de seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten.
Chapter 2. Installing options
11
Statement 1:
DANGER
Electrical current from power, telephone, and communication cables is
hazardous. To avoid a shock hazard:
v Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical
storm.
v Connect all power cords to a properly wired and grounded electrical
outlet.
v Connect to properly wired outlets any equipment that will be attached to
this product.
v When possible, use one hand only to connect or disconnect signal
cables.
v Never turn on any equipment when there is evidence of fire, water, or
structural damage.
v Disconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
v Connect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached
devices.
To connect:
To disconnect:
1. Turn everything OFF.
1. Turn everything OFF.
2. First, attach all cables to devices.
2. First, remove power cords from outlet.
3. Attach signal cables to connectors.
3. Remove signal cables from connectors.
4. Attach power cords to outlet.
4. Remove all cables from devices.
5. Turn device ON.
12
xSeries 440: Option Installation Guide
Statement 2:
CAUTION:
When replacing the lithium battery, use only IBM Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system has
a module containing a lithium battery, replace it only with the same module
type made by the same manufacturer. The battery contains lithium and can
explode if not properly used, handled, or disposed of.
Do not:
v Throw or immerse into water.
v Heat to more than 100° C (212° F)
v Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
Statement 3:
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
v Do not remove the covers. Removing the covers of the laser product could
result in exposure to hazardous laser radiation. There are no serviceable
parts inside the device.
v Use of controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.
Class 1 Laser Product
Laser Klasse 1
Laser Klass 1
Luokan 1 Laserlaite
Appareil A` Laser de Classe 1
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser
diode. Note the following.
Laser radiation when open. Do not stare into the beam, do not view directly
with optical instruments, and avoid direct exposure to the beam.
Chapter 2. Installing options
13
Statement 4:
≥18 kg (39.7 lbs)
≥32 kg (70.5 lbs)
≥55 kg (121.2 lbs)
CAUTION:
Use safe practices when lifting.
Statement 5:
CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current
from the device, ensure that all power cords are disconnected from the power
source.
2
1
14
xSeries 440: Option Installation Guide
Statement 8:
CAUTION:
Never remove the cover on a power supply or any part that has the following
label attached.
Hazardous voltage, current, and energy levels are present inside any
component that has this label attached. There are no serviceable parts inside
these components. If you suspect a problem with one of these parts, contact
a service technician.
Chapter 2. Installing options
15
Opening the cover
Complete the following steps to open the server cover:
1. Review the information in ″Working inside a server with power on″ and “Before
you begin” on page 9.
2. Slide the server out from the rack.
Latch
N
T
O
E
:
F
R
O
P
O
R
E
P
R
A
IR
F
L
,
W
O
R
E
P
L
T
O
E
C
A
N
N
W
H
IN
,
W
O
S
L
E
F
T
IR
U
IN
A
X
O
M
B
R
E
2
P
F
O
O
R
T
P
N
IT
R
O
R
O
F
F
FA
:
E
R
E
P
L
C
A
E
FA
W
O
R
N
F
IT
N
O
IN
H
T
IN
X
O
M
B
2
F
U
T
E
S
3. Pull the release latch on the left half of the top cover to the right.
4. Using the finger hole in the release latch, open the left half of the cover; then,
open the right half of the cover.
Attention: For proper cooling and airflow, close the cover before turning on
the server. Operating the server for extended periods of time (over 30 minutes)
with the cover open might damage server components.
Removing and replacing the bezel
Complete the following steps to remove and replace the server bezel:
1. Remove the bezel.
a. Press on the two tabs at the top edge of the bezel, and pull the top of the
bezel slightly away from the server.
b. Press on the two tabs at the bottom edge of the bezel, and pull the bezel off
the server. Store the bezel in a safe place.
2. Replace the bezel.
a. Align the four tabs with the slots in the server chassis.
b. Press firmly against the front of the bezel until it snaps into place.
16
xSeries 440: Option Installation Guide
Removing and replacing a hot-swap power supply
Your server comes with two hot-swap power supplies, which can be removed and
replaced without turning off the server. This section provides the information to
properly remove and replace these power supplies.
Power light
Power supply 1
Power supply 2
Power-on light
Power button
Reset button
Power supply
latch
Handle
Before you continue with the power supply-installation procedure, review the
following.
Note: During normal operation, both power supplies must be installed for proper
operation and cooling.
If you install or remove a power supply, observe the following precautions.
Statement 8
CAUTION:
Never remove the cover on a power supply or any part that has the following label
attached.
Hazardous voltage, current, and energy levels are present inside any component that
has this label attached. There are no serviceable parts inside these components. If you
suspect a problem with one of these parts, contact a service technician.
Complete the following steps to remove and replace a power supply.
1. Review the information in “Before you begin” on page 9 through
“Safety Information” on page 11.
2. Remove the front bezel (see “Removing and replacing the bezel” on page 16 for
instructions on removing the front bezel).
3. To remove the power supply from the server, press the release latch; then, lift
the handle on the power supply to the open position and pull the power supply
Chapter 2. Installing options
17
out from the server.
4. To install the new power supply:
a. Place the handle on the power supply in the open position.
b. Slide the power supply into the chassis and press the handle to the closed
position.
5. Verify that the dc power light and the ac power light on the power supply are lit,
indicating that the power supply is operating properly.
6. Replace the front bezel on the server (see “Removing and replacing the bezel”
on page 16 for instructions).
18
xSeries 440: Option Installation Guide
PCI and PCI-X adapters
This section provides information about the expansion slots on the system board
and peripheral component interconnect (PCI or PCI-X) adapters.
The following illustration shows the location of the PCI-X expansion slots on the
PCI-X board.
Note: The illustrations in this document might differ slightly from your hardware.
PCI and PCI-X adapter considerations
Before you install adapters, review the following:
v Locate the documentation that comes with the adapter and follow those
instructions in addition to the instructions in this chapter.
v If you need to change the switch settings or jumper settings on your adapter,
follow the instructions that come with the adapter.
v Video adapters are not supported.
v Some long adapters have extension handles or brackets installed. Before
installing the adapter, you must remove the extension handle or bracket.
v You can install PCI or PCI-X adapters, but they cannot occupy the same bus. For
example, if you install a PCI adapter in slot 1 and a PCI-X adapter in slot 2,
neither adapter will operate properly or might not operate at all.
v You can not install a PCI or PCI-X adapter with a speed faster than the label on
the particular PCI-X slot. For example, if you install a 133 MHz adapter in slot 3,
which is labeled as a 100 MHz slot, the adapters installed in slots 3 and 4 will
not operate properly.
Chapter 2. Installing options
19
v You can install PCI or PCI-X adapters with speeds slower than the label for a
particular PCI-X slot. For example, you can install a 33 MHz adapter in any of
the slots, although the bus for that pair of slots will run at 33 MHz.
v Your server supports six hot-plug 64-bit adapters in the expansion slots located
on the PCI-X board.
Note: You can add up to 12 additional PCI-X slots to your server by connecting
your server to a remote expansion enclosure. For more information about
the expansion enclosure and how to connect your server to it, refer to the
documentation that comes with your expansion enclosure.
Bus
Slot
Supported adapter speed (MHz)
A
1
66
A
2
66
B
3
100
B
4
100
C
5
133
D
6
133
v Your server supports 3.3 V adapters; it does not support 5.0 V adapters.
v Your server uses a rotational interrupt technique to configure PCI-X adapters.
You can use this technique to install PCI-X adapters that currently do not support
sharing of PCI-X interrupts.
v The system scans PCI-X slots to assign system resources. The system attempts
to start the first device found. The search order is: CD-ROM, disk drives,
integrated SCSI devices, PCI-X slots (1, 2, 6, 5, 3, 4), and the integrated
Ethernet controller.
Note: You can use the Configuration/Setup Utility program to change the boot
precedence for your server. Select Start Options from the
Configuration/Setup Utility program main menu.
Installing adapters
Complete the following steps to install an adapter:
Attention: When you handle static-sensitive devices, take precautions to avoid
damage from static electricity. For details on handling these devices, see “Handling
static-sensitive devices” on page 10.
1. Review the information in “Working inside a server with power on” on page 9,
“Before you begin” on page 9, and “Safety Information” on page 11.
2. You must disable the Active PCI-X slots in your server using the operating
system before you insert or remove a hot-plug PCI or PCI-X adapter.
Note: Some operating systems do not support the enabling and disabling of a
PCI-X slot. If your operating system does not support this function, then
turn off your server, and disconnect all external cables and power cords
before proceeding.
3. Pull out on the quick release latches on each side of the server; then, pull the
server out of its rack enclosure until it stops.
4. Open the top cover.
20
xSeries 440: Option Installation Guide
Note: Inside your server there are six PCI-X slots: two 66 MHz, two 100 MHz,
and two 133 MHz. Before attempting to install a new adapter, be sure
there is an available slot for it. If you need additional PCI-X slots, you
can purchase a Remote Expansion Enclosure either from your dealer or
through IBM at http://www.ibm.com/.
Tab
Adapter guide
Adapter
retention
latch
PCI-X
divider
Attention
LED
Power
LED
N
T
O
E
:
F
O
R
P
O
R
P
E
R
A
IR
F
L
,
W
O
R
E
P
L
:
FA
E
E
T
O
C
A
N
N
W
H
IN
O
O
R
T
P
N
IT
R
O
R
O
F
F
M
U
IR
IN
A
X
O
R
B
E
2
F
P
T
,
W
O
S
L
E
F
R
E
P
L
C
A
E
FA
W
O
R
N
F
IT
N
H
T
IN
O
IN
X
O
M
B
2
F
U
T
E
S
5. Set any jumpers or switches as described by the adapter manufacturer.
6. Install the adapter:
a. Open the blue adapter guide by lifting the front edge, as shown in the
illustration.
b. Remove the PCI-X divider from the PCI-X slot by grasping the divider
along the top edge and lifting it from the server.
c. Push the orange adapter retention latch toward the rear of the server and
open the tab.
d. Remove the expansion-slot cover.
e. Carefully grasp the adapter by its top edge or upper corners and align it
with the connector on the PCI-X board.
Note: Some long adapters have extension handles or brackets installed.
Before installing a long adapter, you must remove the extension
handle or bracket.
f. Press the adapter firmly into the adapter connector.
Attention: When you install an I/O adapter, be sure the adapter is
correctly seated in the connector slot. Improperly seated adapters might
cause damage to the board, the riser card, or the adapter.
Chapter 2. Installing options
21
7.
8.
9.
10.
g. Reinstall the PCI-X dividers between the Active PCI adapter slots.
h. Push down on the blue adapter guide to keep the adapter steady.
i. Close the tab. The orange adapter retention latch will click into place,
securing the adapter.
Connect the internal cables to the adapter. If you are installing a ServeRAID™
adapter, refer to “Cabling a ServeRAID adapter” for instructions.
If you have other options to install or remove, do so now.
Close the cover on the server.
Enable the slot or turn on the server, depending on your operating system.
Cabling a ServeRAID adapter
You can install an optional IBM ServeRAID adapter in your server to control the
internal hot-swap hard disk drives and external hard disk drives. Refer to your
ServeRAID adapter option documentation for complete instructions on installing a
ServeRAID adapter in your server and for additional information on ServeRAID
adapters.
As shipped, your server comes with two SCSI cables:
v One end of the first SCSI cable is attached to the connector on the SCSI
backplane, and the other end is attached to the integrated SCSI controller behind
fans 3 and 4.
v The second SCSI cable is preinstalled along the inside of the server chassis and
both ends are loose inside the server. When you install a ServRAID adapter, you
must connect this cable to the adapter and to the SCSI backplane.
The following procedure describes the internal cabling needed to install a
ServeRAID adapter.
Complete the following steps to cable the ServeRAID adapter.
1. Review the information in “Before you begin” on page 9 through “Safety
Information” on page 11.
2. Turn off the server and disconnect all power cords and external cables; then,
open the server cover (see “Opening the cover” on page 16).
3. Remove fans 3 and 4, which are located just behind the PCI-X slots.
4. Disconnect the short SCSI cable from the SCSI backplane and the integrated
SCSI controller; then, store this short cable in a safe place for future use.
5. Install the ServeRAID adapter in the PCI-X slot (see“Installing adapters” on
page 20).
22
xSeries 440: Option Installation Guide
6. Locate one end of the preinstalled SCSI cable and connect it to the
ServeRAID adapter.
Preinstalled
SCSI cable
Connect to
ServeRAID adapter
Connect to
SCSI backplane
7. Locate the other end of the preinstalled SCSI cable and connect it to the SCSI
backplane.
Front of server
SCSI backplane
connector
8. Reinstall fans 3 and 4.
9. If you have other options to install or remove, do so now.
10. Close the cover on the server; then, reinstall the server in the rack and
connect all external cables.
11. Turn on the server.
Chapter 2. Installing options
23
Installing or replacing a drive
In this section, you will find the instructions needed to install or replace a hot-swap
hard disk drive, diskette drive, CD-ROM drive, and DVD-ROM drive.
Hot-swap hard disk drive
Complete the following steps to install or replace a hot-swap hard disk drive:
Attention: When you handle static-sensitive devices, take precautions to avoid
damage from static electricity. For details on handling these devices, see “Handling
static-sensitive devices” on page 10.
1. Inspect the drive for any signs of damage.
2. Review the information in “Before you begin” on page 9 and “Safety Information”
on page 11.
3. Check the instructions that come with the drive for more information about
installing your drive.
4. Remove the filler panel or defective hard disk drive from the hard disk drive bay.
5. Install the new hard disk drive in the drive bay:
a. Ensure that the handle on the hard disk drive tray is in the open position.
b. Slide the drive into the bay until it stops.
c. Push the handle on the front of the hard disk drive closed.
Flashing green
light indicates
drive activity
Filler panel
Solid amber
light indicates
failed drive
Flashing amber
light indicates
drive rebuild.
6. If you have other options to install or remove, do so now.
24
xSeries 440: Option Installation Guide
Diskette drive
Drive considerations:
v Your xSeries 440 server supports the installation of up to two diskette drives.
v The diskette drive must be installed in the left drive bay.
Complete the following steps to remove and install a diskette drive in your server:
1. Review the information in “Before you begin” on page 9 and “Safety Information”
on page 11.
Attention: The IDE drives installed in your server are not hot-swappable.
2. Turn off the server and disconnect the power cord from the back of the server.
3. Push the diskette drive eject button to the right.
4. Using the tab, pull the diskette drive partially out of the server; then, grasp the
drive and remove it from the server.
5. Install the new diskette drive:
a. Inspect the drive for any signs of damage.
b. Slide the drive into the left drive bay until it stops.
Note: In the unlikely event that no other IDE drives are installed, the
diskette drive must be installed in the right external removable media
bay.
6. If you have other options to install or remove, do so now. Otherwise, connect
the power cords and turn on the server.
Chapter 2. Installing options
25
CD-ROM or DVD-ROM drive
Drive considerations:
v Your xSeries 440 server supports the installation of up to two CD-ROM drives, or
two DVD-ROM drives.
v If no other IDE drives are installed, the diskette drive must be installed in the
right external removable media bay. CD-ROM or DVD-ROM drives can be
installed in either external removable media bay.
Complete the following steps to remove and install a CD-ROM or DVD-ROM drive
in your server:
1. Review the information in “Before you begin” on page 9 and “Safety Information”
on page 11.
Attention: The IDE drives installed in your server are not hot-swappable.
2. Turn off the server and disconnect the power cords from the back of the server.
3. Push the CD-ROM or DVD-ROM eject button to the right.
4. Using the tab, pull the CD-ROM or DVD-ROM drive partially out of the server;
then, grasp the drive and remove it from the server.
5. Install the new CD-ROM or DVD-ROM drive:
a. Inspect the drive for any signs of damage.
b. Slide the CD-ROM or DVD-ROM drive into the drive bay until it stops.
6. If you have other options to install or remove, do so now. Otherwise, connect
the power cords and turn on the server.
26
xSeries 440: Option Installation Guide
SMP Expansion Module
The SMP Expansion Module contains the XceL4™ system cache, DIMMs,
microprocessors, and voltage regulator modules (VRMs) needed to run your server.
This section contains the information needed to install and remove the SMP
Expansion Module, microprocessors, VRMs, and DIMMs.
SMP Expansion Module considerations:
v For your server to operate properly, there must be a minimum of one SMP
Expansion Module and one SMP baffle installed.
v An SMP Expansion Module must contain at least one microprocessor and four
DIMMs.
v If it becomes necessary to remove or install DIMMs, do so through the DIMM
access doors on the SMP Expansion Module. Refer to the “Removing and
replacing DIMMs” on page 34 for the location of the DIMM access doors.
v Before removing or installing SMP Expansion Modules, you must remove the
electromagnetic compatibility (EMC) shield and SMP Expansion cables from the
rear of the server.
v You must run the Configuration/Setup Utility whenever you remove or replace an
SMP Expansion Module or one of its associated options.
Note: The illustrations in this document might differ slightly from your hardware.
Locking levers
CAM opening
Chapter 2. Installing options
27
Removing an SMP Expansion Module and cover
While installing options, you might need to remove one or both of the SMP
Expansion Modules. This section provides instructions on removing an SMP
Expansion Module from the server and removing the cover from the module.
Complete the following steps to remove an SMP Expansion Module from the server:
1. Review the information in “Before you begin” on page 9, “Handling
static-sensitive devices” on page 10, and “Safety Information” on page 11.
2. Turn off the server and peripheral devices, disconnect the power cords and all
external cables from the SMP Expansion Module; then, open the cover (see
“Opening the cover” on page 16 for details).
3. If necessary, remove the SMP baffle and shipping bracket from the server.
a. Remove the shipping thumbscrews from the right side of the server.
Shipping bracket
removal handles
Shipping bracket
SMP Expansion
Module
N
T
O
E
:
F
O
R
P
O
R
P
E
R
A
IR
F
L
,
W
O
R
E
P
L
:
FA
E
E
T
O
C
A
N
N
W
H
IN
O
O
R
T
P
N
IT
R
O
R
O
F
F
M
U
IR
IN
A
X
O
R
B
E
2
F
P
T
S
,
W
O
L
E
F
R
E
P
L
C
A
E
FA
W
O
R
N
F
IT
N
H
T
IN
O
IN
X
O
M
B
2
F
U
T
E
S
Shipping thumbscrews
b. Open the cover.
c. Grasp the shipping bracket by the removal handles and lift it up and out of
the server.
Note: If there is one SMP Module installed, you will need to remove the
SMP baffle from the server; then, remove the shipping bracket from
the lower SMP Module as described in steps 3a through 3c.
4. To remove the EMC shield from the rear of the server:
a. Remove the blue thumbscrews holding the EMC shield to the server.
EMC shields
Thumbscrews
For use with one
SMP Module
28
xSeries 440: Option Installation Guide
For use with two
SMP Modules
b. Remove the EMC shield from the rear of the server.
Note: The illustrations in this document might differ slightly from your hardware.
Scalability
Cables
EMC Shield
N
T
O
E
:
F
O
R
P
O
R
P
E
R
A
IR
F
L
,
W
O
R
E
P
L
:
FA
E
E
T
O
C
A
N
N
W
H
IN
O
O
R
T
P
N
IT
R
O
R
O
F
F
M
U
IR
IN
A
X
O
R
B
E
2
F
P
T
,
W
O
S
L
E
F
R
E
P
L
C
A
E
FA
W
O
R
N
F
IT
N
H
T
IN
O
IN
X
O
M
B
2
F
U
T
E
S
SMP baffle
5. Grasp each of the locking levers and lift them up slightly.
6. Working from the right side of the server, rotate the two locking levers toward
you until they are fully extended, as shown.
Latch
Locking
levers
Finger relief
N
T
O
E
:
F
O
R
P
O
R
P
E
R
A
IR
F
L
,
W
O
R
E
P
L
C
A
T
O
N
E
:
FA
E
N
W
H
IN
O
O
R
T
P
N
IT
R
O
R
O
F
F
M
U
IR
IN
A
X
O
R
B
E
2
F
P
T
,
W
O
S
L
E
F
R
E
P
L
C
A
E
FA
W
O
R
N
F
IT
N
H
T
IN
O
IN
X
O
M
B
2
F
U
T
E
S
Handle
Attention: When removing the SMP Module from the server, lift it out
carefully, taking care not to damage the components on the center plane.
7. Use the handle and the finger relief on the SMP Expansion Module cover to
carefully lift the SMP Expansion Module out of the server.
Chapter 2. Installing options
29
Note: The illustrations in this document might differ slightly from your hardware.
8. Remove the SMP Expansion Module cover:
a. Place the SMP Expansion Module on a flat, level surface.
b. Rotate the two locking levers just beyond the edge of the SMP Expansion
Module cover until they stop; then, using the locking levers, lift the cover off
the circuit board.
30
xSeries 440: Option Installation Guide
DIMMs
This section contains instructions on how to install, add, and remove DIMMS. It
includes information about Active Memory and Memory Mirroring. Before preforming
any of the procedures in this section, read the “Safety Information” on page 11,
“Handling static-sensitive devices” on page 10, and the DIMM considerations on
page 32.
Your xSeries 440 server supports up to sixteen 3.3 V, 168 pin, 133 MHZ ECC
SDRAM DIMMs in each SMP Expansion Module. With both SMP Expansion
Modules installed, the server can support a maximum of 32 SDRAM DIMMS for a
total of 32 GB of memory in your server.
Notes:
1. DIMMs can be removed and replaced through the access doors on the top of
the SMP Expansion Module.
2. The illustrations in this document might differ slightly from your hardware.
DIMM
bank 2
Chapter 2. Installing options
31
DIMM considerations:
v Your xSeries 440 server supports 512 MB and 1 GB DIMMs, for a maximum of
32 GB of system memory depending on your configuration. See the
ServerProven list at http://www.ibm.com/pc/compat/ for a list of memory modules
you can use with your server.
v Your server comes with four 512 MB DIMMs installed in slots 1, 3, 5, and 7 in the
SMP Expansion Module. When installing additional memory modules, you must
install four DIMMS at a time and in the order described to maintain performance.
(See the following figure for memory connector locations.)
v When installing or removing DIMMs, it must be done in banks of four and in the
following order:
1. Bank 1 = DIMM connectors 1, 3, 5, 7
2. Bank 2 = DIMM connectors 9, 11, 13, 15
3. Bank 3 = DIMM connectors 2, 4, 6, 8
4. Bank 4 = DIMM connectors 10, 12, 14, 16
Note: The illustrations in this document might differ slightly from your hardware.
Bank 1 (standard)
Bank 3
Bank 2
Bank 4
DIMM error
indicators are
built into
each handle.
v Each DIMM in an individual bank must be of the same size and clock speed to
ensure the server will operate properly. For example, in bank 1 your server came
with four 512 MB DIMMs installed. In bank 2, you can install four 512 MB or four
1 GB DIMMs.
v When using Memory Mirroring, all of the DIMMs in each memory port must be
the same size and clock speed.
v Memory ports:
– Memory Port one
- Bank 1 = DIMM connectors 1, 3, 5, 7
- Bank 3 = DIMM connectors 2, 4, 6, 8
– Memory Port two
- Bank 2 = DIMM connectors 9, 11, 13, 15
- Bank 4 = DIMM connectors 10, 12, 14, 16
32
xSeries 440: Option Installation Guide
v When you install or remove DIMMs, the server configuration information
changes. Therefore, you must change and save the new configuration
information by using the Configuration/Setup Utility program. When you restart
the server, the system displays a message indicating that the memory
configuration has changed. Start the Configuration/Setup Utility program and
select Save Settings. If you need instructions, see Chapter 2. Configuring your
server in the User’s Guide on the IBM Documentation CD.
Active Memory
Active Memory is an IBM feature that improves the reliability of the DIMMs through
Memory Mirroring, Memory Scrubbing and Memory ProteXion™ .
v Memory Mirroring allows you to improve the memory reliability of your server by
creating a mirror of the data in memory port one and storing it in memory port
two.
Note: For Memory Mirroring to work, you must have the same amount of
memory in both memory ports. For more information about the memory
ports, refer to the DIMM considerations on page 32.
Complete the following steps to enable Memory Mirroring.
1. Check your operating system documentation to be sure that it supports
Memory Mirroring.
2. Install DIMMs of the same size and clock speed in the two memory ports.
3. Enable Memory Mirroring in the Configuration/Setup Utility:
a. Turn on the server and watch the monitor screen.
b. When the message Press F1 for Configuration/Setup appears, press
F1.
c. From the Configuration/Setup Utility main menu, select Advance
Features.
d. Select and enable Memory Mirroring.
e. Save and exit the Configuration/Setup Utility program.
How does Memory Mirroring work?
When Memory Mirroring is enabled, the data that is written to memory is stored
in two locations. One copy is kept in the memory port one DIMMs, while a
second copy is kept in the memory port two DIMMs. During the execution of the
read command, the data is read from the DIMM with the least amount of reported
memory errors through Memory Scrubbing, which is enabled with Memory
Mirroring.
If Memory Scrubbing determines the DIMM is damaged beyond use, read and
write operations are redirected to the remaining good DIMM. Memory Scrubbing
then reports the damaged DIMM and the Light Path Diagnostics display the error.
After the damaged DIMM is replaced, Memory Mirroring then copies the mirrored
data back into the new DIMM.
v Memory Scrubbing is an automatic daily test of all the system memory that
detects and reports memory errors that might be developing before they cause a
server outage.
Note: Memory Scrubbing and Memory ProteXion work in conjunction with each
other and do not require Memory Mirroring to be enabled to work properly.
How does Memory Scrubbing work?
Chapter 2. Installing options
33
When an error is detected, Memory Scrubbing determines if the error is
recoverable or not. If it is recoverable, Memory ProteXion is enabled and the
data that was stored in the damaged locations is rewritten to a new location. The
error is then reported so that preventative maintenance can be performed. As
long as there are enough good locations to allow the proper operation of the
server, no further action is taken other than recording the error in the error logs.
If the error is not recoverable, then Memory Scrubbing sends an error message
to the Light Path Diagnostics, which then turns on the proper lights and LEDs to
guide you to the damaged DIMM. If Memory Mirroring is enabled, then the
mirrored copy of the data in the damaged DIMM is used to refresh the new
DIMM once it is installed.
v Memory ProteXion reassigns memory bits to new locations within memory when
recoverable errors have been detected.
How does Memory ProteXion work?
Once a recoverable error is found by Memory Scrubbing, Memory ProteXion
writes the data that was to be stored in the damaged memory locations to spare
memory locations within the same DIMM.
Removing and replacing DIMMs
If you need to replace or upgrade the DIMMs in your server, you must remove the
old DIMMs before you insert new ones. This section includes the instructions
needed to properly remove and replace DIMMs from the SMP Expansion Module in
your server.
Attention: When working with DIMMs or other options, you might need to
remove one or both of the SMP Expansion Modules. Before removing an SMP
Expansion Module, be sure to turn off the server and peripheral devices; then,
disconnect all external cables and power cords.
Complete the following steps to remove a DIMM from your server SMP Expansion
Module:
1. Review the information in “Before you begin” on page 9, “Handling
static-sensitive devices” on page 10, and “Safety Information” on page 11.
2. Turn off the server and peripheral devices, disconnect the power cords, and all
external cables from the SMP Expansion Module; then, open the cover (see
“Opening the cover” on page 16 for details).
3. If necessary, remove the top SMP Expansion Module from the server. Refer to
“Removing an SMP Expansion Module and cover” on page 28 for instructions.
4. Open the DIMM access door that covers the DIMM you will be removing.
34
xSeries 440: Option Installation Guide
Note: The illustrations in this document might differ slightly from your hardware.
DIMM access
door
5. Open the retaining clip on each end of the DIMM connector.
6. Lift the DIMM straight up and out of the SMP Expansion Module.
7. Install a new DIMM:
a. Touch the static-protective package containing the DIMM to any unpainted
metal surface on the server. Then, remove the DIMM from the package.
Attention: To avoid breaking the retaining clips or damaging the DIMM
connectors, open and close the clips gently.
b. Insert the DIMM into the connector by aligning the DIMM edges with the
slots at each end of the DIMM connector. Firmly press the DIMM straight
down into the connector by applying pressure on both ends of the DIMM
simultaneously. Be sure that the retaining clips snap into the locked position
when the DIMM is firmly seated in the connector.
DIMM
Retaining
clip
c. If a gap exists between the DIMM and the retaining clips, the DIMM has not
been properly installed. In this case, open the retaining clips and remove the
DIMM; then, reinsert the DIMM.
8. If you have other options to install or remove, do so now.
Note: When you install or remove DIMMs, the server configuration information
changes. Therefore, you must change and save the new configuration
information by using the Configuration/Setup Utility program. Refer to the
User’s Guide on the Documentation CD.
Chapter 2. Installing options
35
Installing and replacing a microprocessor
Your xSeries 440 server comes with a minimum of two microprocessors in the basic
SMP Expansion Module. You can add a second SMP Expansion Module, which
also comes with a minimum of two microprocessors. Each SMP Expansion Module
can support a maximum of four microprocessors so that a fully populated server
contains eight microprocessors. With more than one microprocessor, the server can
operate as a symmetric multiprocessing (SMP) server. With SMP, certain operating
systems and application programs can distribute the processing load among the
microprocessors.
Before you begin:
v Read the documentation that comes with the microprocessor to determine if you
need to update the server basic input/output system (BIOS) code. For the most
current level of BIOS code for the server, go to http://www.ibm.com/pc/support/
on the World Wide Web.
v Obtain an SMP-capable operating system (optional). For a list of supported
operating systems, go to http://www.ibm.com/pc/us/compat/ on the World Wide
Web.
Attention: To avoid damage and ensure proper server operation after you install
a replacement or an additional microprocessor, use a microprocessor that has the
same cache size and type, clock speed, and internal and external clock frequencies
as the microprocessors already installed in the individual SMP Expansion Module.
For a list of microprocessors supported by your server, see the ServerProven list at
http://www.ibm.com/pc/us/compat/ on the World Wide Web.
Notes:
1. To order additional microprocessor options, contact your IBM reseller or IBM
marketing representative.
2. The microprocessor in socket 1 of the basic SMP Expansion Module is the
startup (boot) microprocessor.
3. If you are adding additional microprocessors to an SMP Expansion Module,
populate the empty microprocessor sockets in numeric order, starting with
socket 3. If you install the microprocessors in the wrong order, the server will
not power on.
The following illustration shows the locations of the basic microprocessor and its
VRM on the system board. It also shows the microprocessor baffles and the VRM
slots for the other microprocessor sockets.
36
xSeries 440: Option Installation Guide
Note: The illustrations in this document might differ slightly from your hardware.
Microprocessor 4
VRM connector
Microprocessor 4
baffle
Microprocessor 1 VRM
Microprocessor 1
Microprocessor 2
VRM
Microprocessor 3
VRM connector
Microprocessor 3 socket
Microprocessor 2
Complete the following steps to install a microprocessor:
1. Read the “Handling static-sensitive devices” on page 10 and “Safety
Information” on page 11.
2. Turn off the server and peripheral devices, disconnect the power cords, and all
external cables from the SMP Expansion Module; then, open the cover (see
“Opening the cover” on page 16 for details).
3. Remove the SMP Expansion Module in which you plan to install the
microprocessor; then, remove the module cover and determine the socket
where the microprocessor is to be installed. For details, see “Removing an
SMP Expansion Module and cover” on page 28.
Note: If your server contains only one SMP Expansion Module, remove the
SMP baffle above it to gain access to the module. If your server
contains two SMP Expansion Modules, remove the top module to gain
access to the bottom or lower SMP module.
Attention: When you handle static-sensitive devices, take precautions to avoid
damage from static electricity. For details on handling these devices, see “Handling
static-sensitive devices” on page 10.
4. If you are installing a new microprocessor, go to step 5; otherwise, continue:
a. Verify that you have selected the correct microprocessor to be replaced.
The LED next to the failing microprocessor will be on.
Chapter 2. Installing options
37
Attention: Before attempting to remove the heat sink from the
microprocessor, note that the heat-conducting grease between the heat
sink and the microprocessor might have formed a strong bond. Do not
force the components apart; doing so can damage the microprocessor
pins. If the heat sink does not separate from the microprocessor easily,
loosen one heat sink captive mounting screw first. This allows one corner
of the heat sink to be lifted off of the microprocessor; then, you can loosen
the other captive mounting screw and remove the heat sink.
Captive screws
VRM 3
Heat sink 3
Microprocessor 3
Microprocessor
locking lever
b. Using a screwdriver, loosen the two captive mounting screws on the heat
sink, alternating between screws until they release from the SMP board;
then, remove the heat sink.
c. Lift the microprocessor locking lever to the open position and remove the
microprocessor.
5. Install the VRM in the slot adjacent to the microprocessor socket.
Note: If you are installing an additional microprocessor, note that the new
microprocessor comes in a kit with a VRM.
a. If you are replacing a failed VRM:
1) Verify that you have selected the correct VRM to be replaced. The LED
next to the failing VRM will be on.
2) Grasp the VRM at both upper corners and lift it out of the slot.
38
xSeries 440: Option Installation Guide
b. Holding the new VRM by the upper corners, plug it firmly into the slot.
6. If necessary, remove the microprocessor baffle from the microprocessor
socket. Keep the microprocessor baffle for possible future use.
7. Touch the static-protective package containing the new microprocessor to any
unpainted metal surface on the server; then, remove the microprocessor from
the package.
8. Install the microprocessor:
a. Ensure that the microprocessor locking lever is in the open position to
permit plugging in the microprocessor.
b. Remove the protective tape from the microprocessor socket.
c. Align the triangle icon on the microprocessor with the triangle icon on the
socket and press the microprocessor gently into the socket.
Attention: Make sure that the microprocessor is aligned correctly before
you proceed. To avoid bending the pins on the microprocessor, do not use
excessive force when pressing it into the socket.
d. Close the locking lever to secure the microprocessor.
9. If you have installed an additional microprocessor:
a. Remove the heat sink from its package and detach the protective cover
from the bottom of the heat sink
Chapter 2. Installing options
39
Attention: Do not disturb or contaminate the heat-conducting grease on
the bottom of the new heat sink. Doing so damages its heat-conducting
capability and exposes the new microprocessor to overheating.
Captive screws
Heat sink
Protective cover
b. Align the heat sink over the microprocessor; then, carefully set it down, on
top of the microprocessor.
10.
11.
12.
13.
c. Using a screwdriver, secure the heat sink to the microprocessor socket on
the SMP board using the two captive mounting screws. Press firmly on the
screws and tighten them, alternating between them. Do not overtighten the
screws.
Close the SMP Expansion Module top cover; then, install the module in the
server. For details, see“Reinstalling an SMP Expansion Module and cover” on
page 41.
If you have other options to install or remove, do so now.
Close the cover on the server; then, reinstall the server in the rack and
connect all external cables. For details, see “Closing the cover” on page 49.
Turn on the server.
Note: When you install or remove microprocessors, the server configuration
information changes. Therefore, you must change and save the new
configuration information by using the Configuration/Setup Utility
program. Refer to the User’s Guide on the Documentation CD.
40
xSeries 440: Option Installation Guide
Reinstalling an SMP Expansion Module and cover
After installing options in the SMP Expansion Module, you will need to reinstall the
SMP Expansion Module cover and reinstall the SMP Expansion Module in the
server.
Complete the following steps to reinstall the SMP Expansion Module cover:
1. Install the cover on the SMP Expansion Module:
a. Set the cover on top of the expansion module.
b. Extend the locking levers as shown in the illustration; then, let the cam on
the front of the cover fall into the cam opening on the SMP Expansion
Module circuit board.
Locking levers
CAM opening
c. Release the locking levers and align the rear of the cover with the rear edge
of the circuit board.
d. Press down on the cover until it snaps into place.
Chapter 2. Installing options
41
e. Lift slightly on the locking levers and rotate them back until they stop.
Note: The illustrations in this document might differ slightly from your
hardware.
Locking
levers
Handle
2. Install the SMP Expansion Module into the server.
Locking
levers
Center plane
N
T
O
E
:
F
O
R
P
O
R
P
E
R
A
IR
F
L
,
W
O
R
E
P
L
:
FA
E
E
T
O
C
A
N
N
W
H
IN
O
O
R
T
P
N
IT
R
O
R
O
F
F
IN
M
A
X
O
R
B
E
2
F
P
U
IR
T
,
W
O
S
L
E
F
R
E
P
L
C
A
E
FA
W
O
R
N
F
IT
N
H
T
IN
O
IN
X
O
M
B
2
F
U
T
E
S
Handle
a. Lift the SMP Expansion Module by its handle and use the finger relief to
hold the SMP module steady.
b. Being careful not to damage the components on the center plane, place the
SMP Expansion Module into the server.
c. Release the handle and slide the SMP Expansion Module toward the center
plane until it stops.
42
xSeries 440: Option Installation Guide
d. Rotate the SMP Expansion Module locking levers forward until the SMP
Expansion Module is securely fastened in place. Refer to the following
illustration.
Note: The illustrations in this document might differ slightly from your
hardware.
Center plane
Locking
levers
Cover
Handle
3. If you have other options to install or remove, do so now.
4. Close the cover on the server; then, reinstall the server in the rack and connect
all external cables. For details, see “Closing the cover” on page 49.
5. Turn on the server.
Note: When you install or remove SMP Expansion Modules, the server
configuration information changes. Therefore, you must change and save
the new configuration information by using the Configuration/Setup Utility
program. Refer to the User’s Guide on the Documentation CD.
Chapter 2. Installing options
43
Replacing and troubleshooting fans
Your xSeries 440 server has four hot-swap fan assemblies, two 150 mm x 38 mm,
and two 150 mm x 51 mm fans. The two 150 mm x 38 mm fans (fan 3 and fan 4)
are located just behind the PCI-X planar and are used to cool the power supplies,
PCI-X slots, and the I/O board. The two 150 mm x 51 mm fans (fan 1 and fan 2)
are located toward the front of the server and are used to cool the SMP Expansion
Modules. Refer to the following illustration.
Note: The illustrations in this document might differ slightly from your hardware.
Fan 4
Latch release
N
T
O
E
:
F
O
R
P
O
R
P
E
Fan 2
R
A
IR
F
L
,
W
O
R
E
P
L
C
A
E
FA
W
O
R
N
F
IT
N
H
T
IN
O
IN
X
O
M
B
2
F
U
T
E
S
Fan 3
N
T
O
E
:
F
O
R
P
O
R
P
E
R
A
IR
F
L
,
W
O
R
E
P
L
C
A
E
FA
W
O
R
N
F
IT
N
H
T
IN
O
IN
X
O
M
B
2
F
U
T
E
S
Fan 1
Each fan has a light located on the top left side. When the fan is operating
correctly, this light is on. If a fan stops working, the Light Path Diagnostics feature
will light a system-error light on the front of the server, indicating that there is a
problem and guide you to the defective fan. When this occurs, first identify the
defective fan; then, using the appropriate procedure, remove and replace the fan.
Replacing fans 1 and 2
As shown in the following illustration, fans 1 and 2 are located on the right side of
the server, and cool the SMP Expansion Modules. These fans are redundant,
meaning that if one fails, the remaining fan will temporarily speed up to properly
cool the SMP Expansion Modules. In the event of a failure, replace the
malfunctioning fan within 48 hours.
Complete the following steps to replace fans 1 and 2:
1. Review the information in “Working inside a server with power on” on page 9
and “Before you begin” on page 9.
Attention: All fans must be replaced within 48 hours of failing.
2. Remove the fan from the server:
44
xSeries 440: Option Installation Guide
a. Place your fingers into the two finger holes on the top of the fan and
squeeze them together.
Note: The illustrations in this document might differ slightly from your
hardware.
Fan 4
Latch release
N
T
O
E
:
F
O
R
P
O
R
P
E
Fan 2
R
A
IR
F
L
,
W
O
R
E
P
L
C
A
E
FA
W
O
R
N
F
IT
N
H
T
IN
O
IN
X
O
M
B
2
F
U
T
E
S
Fan 3
N
T
O
E
:
F
O
R
P
O
R
P
E
R
A
IR
F
L
,
W
O
R
E
P
L
C
A
E
FA
W
O
R
N
F
IT
N
H
T
IN
O
IN
X
O
M
B
2
F
U
T
E
S
Fan 1
b. Lift the fan out of the server.
3. Orient the new fan so that the light on the top of the fan is to the right side of
the server.
4. Push the replacement fan assembly into the server until it clicks into place.
5. If you have other options to install or remove, do so now.
6. Close the cover. See “Closing the cover” on page 49.
Replacing fans 3 and 4
As shown in the illustration, these two fans (fan 3 and fan 4) are located in front of
the I/O board and the PCI-X slots. They are used to cool the hard disk drives, I/O
board, and PCI-X slots.These fans are redundant, meaning that if one fails, the
remaining fan will temporarily speed up to properly cool the I/O components in the
server. In the event of a failure, you must replace the malfunctioning fan within 48
hours.
Complete the following steps to replace fans 3 and 4:
1. Review the information in “Working inside a server with power on” on page 9
and “Before you begin” on page 9.
Attention: All fans must be replaced within 48 hours of failing.
2. Remove the fan from the server:
a. Press the latch release to the right and let the handle come up.
Chapter 2. Installing options
45
Note: The illustrations in this document might differ slightly from your
hardware.
Fan 4
Latch release
N
T
O
E
:
F
O
R
P
O
R
P
E
Fan 2
R
A
IR
F
L
,
W
O
R
E
P
L
C
A
E
FA
W
O
R
N
F
IT
N
H
T
IN
O
IN
X
O
M
B
2
F
U
T
E
S
Fan 3
N
T
O
E
:
F
O
R
P
O
R
P
E
R
A
IR
F
L
,
W
O
R
E
P
L
C
A
E
FA
W
O
R
N
F
IT
N
H
T
IN
O
IN
X
O
M
B
2
F
U
T
E
S
Fan 1
b. Grasp the handle and lift the fan out of the server.
3. Orient the new fan so that the latch release on the top of the fan is to the right
side of the server.
4. With the handle raised, push the replacement fan assembly into the server until
it clicks into place.
5. Push the handle down until it clicks into place under the latch release.
6. If you have other options to install or remove, do so now.
7. Close the cover. See “Closing the cover” on page 49.
46
xSeries 440: Option Installation Guide
Replacing the battery
When replacing the battery you must replace it with a lithium battery of the same
type, from the same manufacturer. To avoid possible danger, read and follow the
safety statement below.
To order replacement batteries, call 1-800-772-2227 within the United States, and
1-800-465-7999 or 1-800-465-6666 within Canada. Outside the U.S. and Canada,
call your IBM reseller or IBM marketing representative.
Note: After you replace the battery, you must reconfigure your server and reset the
system date and time.
CAUTION:
When replacing the lithium battery, use only IBM Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system has
a module containing a lithium battery, replace it only with the same module
type made by the same manufacturer. The battery contains lithium and can
explode if not properly used, handled, or disposed of.
Do not:
v Throw or immerse into water.
v Heat to more than 100°C (212°F)
v Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
Complete the following steps to replace the battery:
1. Read “Safety” on page v, and follow any special handling and installation
instructions supplied with the replacement battery.
2. Turn off the server and peripheral devices, disconnect the power cords, and all
external cables from the server; then, open the cover (see “Opening the cover”
on page 16 for details).
3. Remove fans 3 and 4 from the server (see “Replacing fans 3 and 4” on page 45
for details).
Chapter 2. Installing options
47
4. Remove the battery:
a. Use one finger to lift the battery clip over the battery.
b. Use one finger to slightly slide the battery out from its socket. The spring
mechanism will push the battery out toward you as you slide it from the
socket.
c. Use your thumb and index finger to pull the battery from under the battery
clip.
d. Ensure that the battery clip is touching the base of the battery socket by
pressing gently on the clip.
5. Insert the new battery:
a. Tilt the battery so that you can insert it into the socket, under the battery
clip.
b. As you slide it under the battery clip, press the battery down into the socket.
6. Install fans 3 and 4 in the server (see “Replacing fans 3 and 4” on page 45 for
details).
7. Reinstall the server cover, and connect the cables.
8. Turn on the server.
9. Start the Configuration/Setup Utility program and set configuration parameters.
v Set the system date and time.
v Set the power-on password.
v Reconfigure your server.
48
xSeries 440: Option Installation Guide
Closing the cover
Complete the following steps to install the server cover:
1. Close the cover by first closing the right side; then, close the left side and press
down to latch the two halves of the cover in place.
N
T
O
E
:
F
O
R
P
O
R
P
E
R
A
IR
F
L
,
W
O
R
E
P
L
:
FA
E
E
T
O
C
A
N
N
W
H
IN
O
O
R
T
P
N
IT
R
O
R
O
F
F
M
U
IR
IN
A
X
O
R
B
E
2
F
P
T
,
W
O
S
L
E
F
R
E
P
L
C
A
E
FA
W
O
R
N
F
IT
N
H
T
IN
O
IN
X
O
M
B
2
F
U
T
E
S
2. Reconnect all external cables and power cords to the server; then, plug the
power cords into properly grounded electrical outlets. Refer to “I/O connectors
and indicators on your server” on page 51 for connector locations.
3. Turn on your server.
Chapter 2. Installing options
49
Cabling the server
See “I/O connectors and indicators on your server” on page 51 for a description of
the I/O connectors on the rear of the server.
The following illustration shows the cable routing for a typical server configuration.
Detailed cabling instructions, including the use of the cable management arm
(shipped with the server) are in the Rack Installation Instructions provided with the
server.
Notes:
1. The illustrations in this document might differ slightly from your hardware.
2. See the documentation that comes with the options for additional cabling
instructions. It might be easier for you to route any cables before you install
certain options.
3. If you have just plugged the power cords of the server into an electrical outlet,
you must wait 30 seconds before pressing the power-control button.
Cable straps
50
xSeries 440: Option Installation Guide
Chapter 3. I/O connectors and indicators
You can use the information in this chapter to cable the server.
I/O connectors and indicators on your server
Your server has the following I/O connectors:
v Universal Serial Bus (USB) connectors
v Keyboard connector
v Video connector
v
v
v
v
v
v
Auxiliary-device (pointing device) connector
System management ports
RXE Expansion Ports
SCSI port
SMP Expansion Ports
Remote Supervisor Adapter ports
– One ASM interconnect (peer-to-peer) port (RJ-14)
– One Ethernet port (remote server management using network, RJ-45)
– One serial port (remote server management using modem)
– One external power connector
v Ethernet connectors
© Copyright IBM Corp. 2002
51
Universal Serial Bus ports
Your server has three Universal Serial Bus (USB) ports, which are configured
automatically. USB is a serial interface standard for telephony and multimedia
devices. It uses Plug and Play technology to determine the type of device attached
to the connector.
USB cables and hubs
You need a 4-pin cable to connect devices to USB 1, USB 2, and USB 3. If you
plan to attach more than three USB devices, you must use a hub to connect the
devices. The hub provides multiple connectors for attaching additional external USB
devices.
USB technology provides up to 12 (MBps) speed with a maximum of 127 external
devices and a maximum signal distance of 5 meters (16 ft) per segment.
USB-port connectors
There are two USB-port connectors on the rear of the server and one USB-port
connector on the front. These USB-port connectors are used to attach USB
compatible devices to the server.
The following illustration shows the pin-number assignments for the USB-port
connectors on your server.
1
4
Keyboard connector
There is one keyboard connector on the rear of the server.
Note: If you attach a standard keyboard to the keyboard connector, the USB ports
and devices will be disabled during the power-on self-test (POST).
The following illustration shows the pin-number assignments for the keyboard
connector on the end of the cable.
6
5
4
3
2
1
Video connector
The following illustration shows the pin-number assignments for the 15-pin analog
video connector on the rear of the server.
52
xSeries 440: Option Installation Guide
5
1
15
11
Auxiliary-device (pointing device) connector
There is one auxiliary-device connector that supports a mouse or other pointing
device located on the rear of the server just under the keyboard connector.
The following illustration shows the pin-number assignments for the auxiliary-device
connector on the end of the cable.
6
5
4
3
1
2
RXE Expansion Port
There are two RXE Expansion Ports that are used to connect your server to a
remote I/O enclosure.
The following illustration shows the pin-number assignments for the RXE Expansion
Port on the end of the cable.
48
2
47
1
SMP Expansion Port
There are up to six SMP Expansion Ports that are used to interconnect the SMP
Modules in your server.
The following illustration shows the pin-number assignments for the SMP Expansion
Port on the end of the cable.
48
2
47
1
Remote Supervisor Adapter communication ports
The server has four communication ports that are used by the Remote Supervisor
Adapter. Three of the ports are located on the adapter and one is located at the
lower left corner of the rear panel (as viewed from the rear).
If you want to use the Remote Supervisor Adapter to manage the server remotely
or to connect the server to another server, connect the appropriate cables to the
Remote Supervisor Adapter ports.
To enable remote server management through a network, use the Remote
Supervisor Adapter Ethernet port (RJ-45). To enable remote server management
using a modem, use the Remote Supervisor Adapter serial port. To connect the
Chapter 3. I/O connectors and indicators
53
server with another server, use the ASM interconnect port (RJ-14). See the Remote
Supervisor Adapter documentation on the IBM Documentation CD for more
information.
The following illustration shows the communication ports on the Remote Supervisor
Adapter.
Error LED
(amber)
ASM interconnect
port
Ethernet link LED
(green)
External power
connector
Ethernet activity LED
(green)
Power LED
(green)
Management port
10/100
Ethernet port
External power connector
This connector provides power to the Remote Supervisor Adapter,
independent of the server power supply.
Note: This connector is not supported on this server.
Error LED
The amber Error LED indicates an error on the Remote Supervisor Adapter.
Advanced System Management (ASM) interconnect port
Attach an ASM Interconnect module (which comes with the server) to this
port to connect the Remote Supervisor Adapter to the other devices on the
ASM Interconnect network.
Ethernet link LED
This green light, located on the right of the Ethernet port, lights when there
is an active link connection on the Ethernet controller for the Ethernet port.
Ethernet activity LED
This green light, located on the left of the Ethernet port, lights when there is
activity on the Ethernet LAN connected to the Ethernet port.
10/100 Ethernet port
Connect a category 3 or category 5 Ethernet cable to this port to enable a
LAN connection or TELNET session. The Ethernet port LEDs on the
Remote Supervisor Adapter indicate the link is good and activity is taking
place on the network.
Management port
Connect a serial cable to this port to enable system management through a
modem, or connect a null modem cable to enable system management
through a workstation or laptop computer.
Power LEDs
The green power LED indicates the status of the power connection.
Gigabit Ethernet port
Your server comes with an integrated Gigabit Ethernet controller. This controller
provides an interface for connecting to 10-Mbps, 100-Mbps, or 1000-Mbps networks
54
xSeries 440: Option Installation Guide
and provides full-duplex (FDX) capability, which enables simultaneous transmission
and reception of data on the Ethernet local area network (LAN).
To access the Ethernet port, connect a Category 3, 4, or 5 unshielded twisted-pair
(UTP) cable to the RJ-45 connector on the rear of your server.
Note: The 100BASE-TX/1000BASE-T Fast Ethernet standard requires that the
cabling in the network be Category 5 or higher.
The Ethernet (RJ-45) connector has two lights. The Ethernet-link status light is on
the left. When this green light is on, there is an active connection on the Ethernet
port. The Ethernet transmit/receive activity light is on the right. When this amber
light is on, there is activity between the server and the network. These lights have
the same functions as the Ethernet-link status light and the Ethernet
transmit/receive activity light on the rear of the server (refer to the User’s Guide on
the IBM Documentation CD).
Configuring the Gigabit Ethernet controller
The Ethernet controller is a PCI Plug and Play device. You do not need to set any
jumpers or configure the controller for your operating system before you use the
Ethernet controller. However, you must install a device driver to enable your
operating system to address the Ethernet controller. The device drivers are provided
on the ServerGuide CD.
When you connect your server to the network, the Ethernet controller automatically
detects the data-transfer rate (10 Mbps, 100 Mbps, or 1000 Mbps) on the network
and then sets the controller to operate at the appropriate rate. In addition, if the
Ethernet ports that your server is connected to support auto-negotiation, the Gigabit
Ethernet controller will set the appropriate duplex state. That is, the Ethernet
controller will adjust to the network data rate, whether the data rate is standard
Ethernet (10BASE-T), Fast Ethernet (100BASE-TX/1000BASE-T), half duplex
(HDX), or full duplex (FDX). The controller supports half-duplex (HDX) and
full-duplex (FDX) modes at both speeds.
Chapter 3. I/O connectors and indicators
55
High-performance Ethernet modes
Your Ethernet controller supports optional modes, such as teaming, load balancing,
fault tolerance, and virtual LANs, which provide higher performance, security, and
throughput for your server. These modes apply to the integrated Ethernet controller
and to the controllers on supported Ethernet adapters, such as the IBM
10/100/1000 Ethernet Adapter or the IBM 10/100/1000 EtherJet™ PCI family of
adapters.
Teaming mode
Your Ethernet controller provides options, called teaming options, that apply to
supported Ethernet controllers. A team can consist of two or more Ethernet
controllers, two Ethernet adapters, or a mix of integrated Ethernet controllers and
Ethernet adapters. These options increase throughput and fault tolerance when
running with Windows 2000, Windows NT 4.0, Linux, or NetWare 4.1x or later.
v Adapter fault tolerance (AFT) provides automatic redundancy for your Ethernet
controllers. You can configure either the integrated Ethernet controller or an
Ethernet adapter as the primary Ethernet controller. If the primary link fails, the
secondary controller takes over. When the primary link is restored to an
operational state, the Ethernet traffic switches back to the primary Ethernet
controller. Adapter fault tolerance supports from two to four controllers per team.
v Adaptive load balancing (ALB) enables you to balance the transmission data
flow among two to four controllers. ALB also includes the AFT option. You can
use ALB with any 100BASE-TX/1000BASE-T switch.
v Cisco Fast EtherChannel (FEC) creates a team of two to four controllers to
increase transmission and reception throughput. FEC also includes the AFT
option. You can use FEC only with a switch that has FEC capability.
If you use supported Ethernet adapters in your server, refer to the documentation
that comes with the adapters for more information about the teaming modes.
Ethernet port connector
The following illustration shows the pin-number assignments for the RJ-45
connector. These assignments apply to both 10BASE-T and 100/1000BASE-TX
devices.
Link LED
(green)
Activity LED
(green)
1
56
xSeries 440: Option Installation Guide
8
Appendix. Notices
This publication was developed for products and services offered in the U.S.A.
IBM may not offer the products, services, or features discussed in this document in
other countries. Consult your local IBM representative for information on the
products and services currently available in your area. Any reference to an IBM
product, program, or service is not intended to state or imply that only that IBM
product, program, or service may be used. Any functionally equivalent product,
program, or service that does not infringe any IBM intellectual property right may be
used instead. However, it is the user’s responsibility to evaluate and verify the
operation of any non-IBM product, program, or service.
IBM may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you any
license to these patents. You can send license inquiries, in writing, to:
IBM Director of Licensing
IBM Corporation
North Castle Drive
Armonk, NY 10504-1785
U.S.A.
INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS
PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. Some states do not allow disclaimer of express or
implied warranties in certain transactions, therefore, this statement may not apply to
you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. IBM may make improvements and/or
changes in the product(s) and/or the program(s) described in this publication at any
time without notice.
Any references in this publication to non-IBM Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those
Web sites. The materials at those Web sites are not part of the materials for this
IBM product, and use of those Web sites is at your own risk.
IBM may use or distribute any of the information you supply in any way it believes
appropriate without incurring any obligation to you.
Edition notice
© COPYRIGHT INTERNATIONAL BUSINESS MACHINES CORPORATION, 2002.
All rights reserved.
Note to U.S. Government Users — Documentation related to restricted rights —
Use, duplication or disclosure is subject to restrictions set forth in GSA ADP
Schedule Contract with IBM Corp.
© Copyright IBM Corp. 2002
57
Trademarks
The following terms are trademarks of International Business Machines Corporation
in the United States, other countries, or both:
Alert on LAN
Active PCI-X
Active PCI
Active Memory
Chipkill
EtherJet
e-business logo
HelpCenter
HelpWare
IBM
Light Path Diagnostics
Memory ProteXion
NetBAY
OS/2 WARP
Predictive Failure Analysis
ServeRAID
ServerGuide
ServerProven
TechConnect
Tivoli
Tivoli Enterprise
Update Connector
Wake on LAN
X-Architecture
XA-32
XceL4
XpandOnDemand
xSeries
Lotus and Domino are trademarks of Lotus Development Corporation and/or IBM
Corporation in the United States, other countries, or both.
Intel, Celeron, MMX, LANDesk, Pentium, Pentium II Xeon, and Pentium III Xeon are
trademarks of Intel Corporation in the United States, other countries, or both.
Microsoft, Windows, and Windows NT are trademarks of Microsoft Corporation in
the United States, other countries, or both.
UNIX is a registered trademark of The Open Group in the United States and other
countries.
Java and all Java-based trademarks and logos are trademarks or registered
trademarks of Sun Microsystems, Inc. in the United States, other countries, or both.
Linux is a registered trademark of Linus Torvalds.
Other company, product, or service names may be the trademarks or service marks
of others.
Important notes
Processor speeds indicate the internal clock speed of the microprocessor; other
factors also affect application performance.
CD-ROM drive speeds list the variable read rate. Actual speeds vary and are often
less than the maximum possible.
When referring to processor storage, real and virtual storage, or channel volume,
KB stands for approximately 1000 bytes, MB stands for approximately 1000000
bytes, and GB stands for approximately 1000000000 bytes.
58
xSeries 440: Option Installation Guide
When referring to hard disk drive capacity or communications volume, MB stands
for 1 000 000 bytes, and GB stands for 1 000 000 000 bytes. Total user-accessible
capacity may vary depending on operating environments.
Maximum internal hard disk drive capacities assume the replacement of any
standard hard disk drives and population of all hard disk drive bays with the largest
currently supported drives available from IBM.
Maximum memory may require replacement of the standard memory with an
optional memory module.
IBM makes no representation or warranties regarding non-IBM products and
services that are ServerProven«, including but not limited to the implied warranties
of merchantability and fitness for a particular purpose. These products are offered
and warranted solely by third parties.
Unless otherwise stated, IBM makes no representations or warranties with respect
to non-IBM products. Support (if any) for the non-IBM products is provided by the
third party, not IBM.
Some software may differ from its retail version (if available), and may not include
user manuals or all program functionality.
Power cords
For your safety, IBM provides a power cord with a grounded attachment plug to use
with this IBM product. To avoid electrical shock, always use the power cord and
plug with a properly grounded outlet.
IBM power cords used in the United States and Canada are listed by Underwriter’s
Laboratories (UL) and certified by the Canadian Standards Association (CSA).
For units intended to be operated at 115 volts: Use a UL-listed and CSA-certified
cord set consisting of a minimum 18 AWG, Type SVT or SJT, three-conductor cord,
a maximum of 15 feet in length and a parallel blade, grounding-type attachment
plug rated 15 amperes, 125 volts.
For units intended to be operated at 230 volts (U.S. use): Use a UL-listed and
CSA-certified cord set consisting of a minimum 18 AWG, Type SVT or SJT,
three-conductor cord, a maximum of 15 feet in length and a tandem blade,
grounding-type attachment plug rated 15 amperes, 250 volts.
For units intended to be operated at 230 volts (outside the U.S.): Use a cord set
with a grounding-type attachment plug. The cord set should have the appropriate
safety approvals for the country in which the equipment will be installed.
IBM power cords for a specific country or region are usually available only in that
country or region.
IBM power cord part
number
Used in these countries and regions
13F9940
Argentina, Australia, China (PRC), New Zealand, Papua New
Guinea, Paraguay, Uruguay, Western Samoa
Appendix. Notices
59
60
IBM power cord part
number
Used in these countries and regions
13F9979
Afghanistan, Algeria, Andorra, Angola, Austria, Belgium, Benin,
Bulgaria, Burkina Faso, Burundi, Cameroon, Central African Rep.,
Chad, China (Macau S.A.R.), Czech Republic, Egypt, Finland,
France, French Guiana, Germany, Greece, Guinea, Hungary,
Iceland, Indonesia, Iran, Ivory Coast, Jordan, Lebanon,
Luxembourg, Malagasy, Mali, Martinique, Mauritania, Mauritius,
Monaco, Morocco, Mozambique, Netherlands, New Caledonia,
Niger, Norway, Poland, Portugal, Romania, Senegal, Slovakia,
Spain, Sudan, Sweden, Syria, Togo, Tunisia, Turkey, former
USSR, Vietnam, former Yugoslavia, Zaire, Zimbabwe
13F9997
Denmark
14F0015
Bangladesh, Burma, Pakistan, South Africa, Sri Lanka
14F0033
Antigua, Bahrain, Brunei, Channel Islands, China (Hong Kong
S.A.R.), Cyprus, Dubai, Fiji, Ghana, India, Iraq, Ireland, Kenya,
Kuwait, Malawi, Malaysia, Malta, Nepal, Nigeria, Polynesia, Qatar,
Sierra Leone, Singapore, Tanzania, Uganda, United Kingdom,
Yemen, Zambia
14F0051
Liechtenstein, Switzerland
14F0069
Chile, Ethiopia, Italy, Libya, Somalia
14F0087
Israel
1838574
Thailand
6952301
Bahamas, Barbados, Bermuda, Bolivia, Brazil, Canada, Cayman
Islands, Colombia, Costa Rica, Dominican Republic, Ecuador, El
Salvador, Guatemala, Guyana, Haiti, Honduras, Jamaica, Japan,
Korea (South), Liberia, Mexico, Netherlands Antilles, Nicaragua,
Panama, Peru, Philippines, Saudi Arabia, Suriname, Taiwan,
Trinidad (West Indies), United States of America, Venezuela
xSeries 440: Option Installation Guide
Index
A
Active memory 33
adapter
fault tolerance 56
installing 19, 20
PCI bus 20
ServeRAID 22
working with 19
adaptive load balancing
Ethernet port 55
expansion slots
location 19
type 19
external
cabling 50
F
56
failover for redundant Ethernet 56
fan
assemblies 44
fans
replacing and troubleshooting 44
replacing SMP Expansion Module 44
replacing the PCI-X 45
Fast EtherChannel 56
Fast Ethernet 55
filler panel
power-supply bay 17
B
battery replacement
47
C
cabling
external 50
ServeRAID adapter 22
components
location of 2
Remote Supervisor Adapter 7
configuration
hardware, cabling for 50
connector and port locations 51
connectors
Ethernet 56
controller
Ethernet 56
cooling 10
cover
close 49
removing 16
H
handling static-sensitive devices
hard disk drive
IDE 24
installing 24
hardware, major 2
hot-swap and hot-plug devices
power supplies 17
hot-swap power supply
installing 17
10
I
D
DIMMs 31
considerations 32
order of installation 32
removing 34
E
Ethernet
adapter fault tolerance 56
adaptive load balancing 56
Cisco Fast EtherChannel 56
connector pin-number assignments
controller 56
failover support 56
high performance modes 56
modes 56
port 56
teaming 56
Ethernet controller
configuring 55
© Copyright IBM Corp. 2002
56
I/O board
internal connectors 7
I/O connectors 51
installation
order, microprocessors 36
installing
adapters 19
battery 47
hot-swap power supply 17
options 9
internal connectors
I/O board 7
PCI-X 6
SMP Expansion Module 4
K
keyboard
connector
52
61
L
load balancing
reliability, system 10
Remote Supervisor Adapter 53
component locations 7
port 53
replacing
PCI-X fans 45
SMP Expansion Module fans 44
RXE Expansion Port
connector 53
56
M
memory
configuration changes 33
Memory mirroring 33
microprocessor 36
order of installation 36
modes, Ethernet 56
mouse
connector 53
S
N
notes, important
58
O
option
installing 9
order of installation, microprocessors
36
P
PCI
expansion slots 19
PCI-X
internal connectors 6
pin-number assignments
Ethernet 56
pointing device
connector 53
port
Ethernet 55, 56
Remote Supervisor Adapter 53
USB 52
USB connector 52
power supply
installing 17
operating requirements 17
Safety 11
ServeRAID adapter
cabling 22
slots See expansion slots 19
SMP
Expansion Module 27
internal connectors 4
removing 28
removing the cover 28
Expansion Port
connector 53
fans 44
SMP Expansion Module
reinstalling the cover 41
reinstalling the SMP Expansion Module
system
reliability 10
T
teaming options
trademarks 58
56
U
USB
cables and hubs 52
connector 52
port connectors 52
W
R
reinstalling
the SMP Expansion Module
62
41
xSeries 440: Option Installation Guide
Web site
compatible options 32, 36
working inside server with power on
9
41

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project