Netgear CMD31T-100NAS Installation guide

CMD31T Cable Modem

Serial number:

MAC address:

Part 1: Unpack the Shipping Carton

Verify all items are present.

CMD31T Cable Modem

Installation Guide

Ethernet cable

Part 2: Install the Cable Modem

1. Complete the connections as shown in the connections diagram below.

a.

b.

c.

a. Connect the coaxial cable to the NETGEAR CMD31T Cable Modem.

b. Use the Ethernet cable to connect your Laptop/PC to the NETGEAR

CMD31T Cable Modem.

c. Connect the power adapter.

2. Power on your computer.

Note: It will take at least 15 minutes for your NETGEAR CMD31T Cable Modem to come online on the network.

3. Wait until the cable modem status shows online. After the modem registers with your Cable Internet Service Provider, the following LEDs should be lit:

• Power LED: solid green

• Online LED: solid green

If the Power LED is not solid green, check your power adaptor connections.

Part 3: Contact Your Cable Operator

1. Call your cable operator and tell the customer service person that you are installing a new cable modem you have bought from a retail store.

Cable Service Provider Contact Information

Cablevision: http://www.cablevision.com/

Charter: 1-888-438-2427

Comcast: 1-800-COMCAST (1-800-266-2278)

Cox: 1-877-794 2324

Time-Warner Cable: http://www.timewarnercable.com/

2. When asked, provide the cable modem ’s Serial Number and MAC Address listed on the front page of this installation guide.

3. Wait for the customer service operator to confirm that your device is active.

• If you do not have internet connection with the new Netgear cable modem , then you should ask the customer service agent to verify whether he or she can see your cable modem online.

• If not, then the customer service agent should help you with instructions to verify why the cable modem will not take connect your High Speed Internet

Service.

• If the customer service agent can confirm that your cable modem is visible as online to the agent, then you should try and reboot your PC/Laptop or Home

Gateway that is connected to cable modem and try checking your online status again.

4. You are now able to enjoy your Internet service with the NETGEAR CMD31T

Cable Modem.

Power adapter

LEDs

Power

• Solid green: Power is on.

• Off: Power is off.

Online

(Cable Link)

• Green blinking: The cable modem is on-line and processing traffic.

• Off: The cable modem is off-line

US (Upstream)

DS (Downstream)

• 1/2 solid amber: Upstream channel 1 is in use.

• 1/2 solid green; Upstream channel 1 and 2 are in use.

• 3/4 solid amber: Upstream channel 1, 2, and 3 are in use.

• 3/4 solid green: Upstream channel 1, 2, 3, and 4 are in use.

• Off: No upstream channels are in use.

• 1/2 solid amber: Downstream channel 1 is in use.

• 1/2 solid green: Downstream channel 1 and 2 are in use.

• 3/4 solid amber: Downstream channel 1, 2, and 3 are in use.

• 3/4 solid green: Downstream channel 1, 2, 3, and 4 are in use.

• Off: No downstream channels are in use.

Ethernet

• Solid green: A device is connected and detected on the 1-Gbps

Ethernet port.

• Green blink: There is data traffic on the 1-Gbps Ethernet port.

• Off: No devices are detected on the Ethernet port.

March 2011

Troubleshooting

No LEDs are lit on the cable modem

Online LED does not light up

Ethernet LED does not light up even though a device is attached

You cannot connect to the

Internet

The cable modem has no power. Make sure that:

• The power adapter is properly connected to the cable modem.

• The power adapter is properly connected to a functioning power outlet. If it is in a power strip, make sure the power strip is turned on.

• You are using the correct power adapter.

There is a hardware connection problem or you do not have cable service. Do the following:

• Make sure the cable connector is securely plugged in at the cable modem.

• Turn the power off and on to the cable modem.

• You may not have active cable service yet. Contact your provider to verify activation.

There is a hardware connection problem. Do the following:

• Make sure the cable connector is securely plugged in to the cable modem and the computer.

• If you are not using the cable included with the cable modem, check that the Ethernet cable is a straight-through patch cable.

It may take up to 15 minutes to establish a connection the first time you power on your cable modem. Always leave your cable modem plugged in to AC power and connected to the cable system. Do the following:

• Check you cable connections. Connectors should be finger tight.

• Make sure that you have powered up in the following sequence:

- Turn on you cable modem first and wait until the LEDs stop flashing.

- If your computer is connected to the cable modem, turn on the computer.

• If you have a home network, check the TCP/IP configuration.

- For Windows, the network properties should be set to

“Obtain an IP address automatically.”

- For Macintosh computers, the TCP/IP (or Network) control panel should be set to “Using DHCP Server.”

Technical Support

Thank you for selecting NETGEAR products.

After installing your device, locate the serial number on the label of your product and use it to register your product at http://www.NETGEAR.com/register. Registration is required before you can use the telephone support service. Registration via our website is strongly recommended.

Go to http://support.netgear.com

for product updates and Web support .

NETGEAR Technical Support: 1-888-638-4327, for US and Canada only.

For complete DoC please visit the NETGEAR EU Declarations of Conformity website at: http://support.netgear.com/app/answers/detail/a_id/11621/

For GNU General Public License (GPL) related information, please visit http:// support.netgear.com/kb_web_files/open_src.asp

WARNING!!

DO NOT stack equipment, or place equipment in tight spaces, or in drawers. Be sure your equipment is surrounded by at least 2” of air space.

This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste

Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union, this product should be treated and recycled in accordance with the laws of your jurisdiction implementing the WEEE Directive.

©2011 by NETGEAR, Inc. All rights reserved. NETGEAR and the NETGEAR logo are registered trademarks of

NETGEAR, Inc. in the United States and/or other countries. Other brand and product names are trademarks or registered trademarks of their respective holders. Information is subject to change without notice.