Diamond E-60 User manual

Diamond E-60 User manual
FORM NO. 1-667R7
October 2005
Price: $5.00
QUIK-LIFT®
power unit
service manual
MODELS
E-60, E-60H
Meyer Products
18513 Euclid Ave. • Cleveland, OH 44112-1084
Phone (216) 486-1313
email•[email protected]
© 2005 Printed in the U.S.A.
Diamond Equipment
6 Angell Lane• Damariscotta, ME 04543-9720
Phone (207) 563-2227
www.diamondplow.com • email [email protected]
FOREWARD
This Service Manual includes complete information for servicing the following Quik-Lift® E - 60, E - 60H Units:
The information is grouped according to the type of work being performed, such as diagnosis and testing, disassembly
and reassembly. Special tools and specifications are also included in this manual.
All information, illustrations and product descriptions contained in this manual are correct at publication time. We do,
however, reserve the right to make changes at any time without prior notice.
MEYER PRODUCTS
IMPORTANT: Maintenance and repairs must be performed with the moldboard on the ground.
SECTION INDEX
Section Number
Section Title .....................................................
0
GENERAL INFORMATION AND
MAINTENANCE ........................................................
GENERAL DESCRIPTION AND
THEORY OF OPERATION ........................................
DIAGNOSIS .............................................................
REPAIR PROCEDURE ..............................................
SPECIFICATIONS .....................................................
1
2
3
4
E-60
Page
1
4
18
25
53
E-60H
Meyer Products reserves the right, under its continuing product improvement program, to change construction or design
details, specifications and prices without notice or without incurring any obligation.
SECTION 0
- GENERAL INFORMATION AND MAINTENANCE
CONTENTS
GENERAL INFORMATION ..................................................
2
•
MODEL IDENTIFICATION ....................................................
2
•
MODEL IDENTIFICATION AND
SERIAL NUMBER LOCATION ..............................................
2
•
MOTOR IDENTIFICATION ...................................................
2
MAINTENANCE ...................................................................
2
•
GENERAL MAINTENANCE ...................................................
2
•
CLEANLINESS .................................................................
2
•
VEHICLE ELECTRICAL SYSTEM ...........................................
3
•
CHECK REGULARLY .........................................................
3
POST-SEASON MAINTENANCE .......................................
3
•
MEYER HYDRAULIC FLUID M-1 .........................................
3
•
REPLACEMENT OF HYDRAULIC FLUID ...................................
3
•
FILTERS ........................................................................
3
PROTECTION AGAINST RUST
CORROSION ............................................................
3
•
AND
-1-
GENERAL INFORMATION
Motor Identification
Model Identification
The Quik Lift® unit is an electrically powered hydraulic
mechanism specifically designed for use with the Meyer
Snow Plow and is available in four models as follows:
E-60
Raises, lowers and angles plow
hydraulically (7-way) and is used with
TM, ST and C series Snow Plows.
E-60H
Raises, lowers and angles plow
hydraulically (7-way) and is used with
the MDII, HM and Diamond Series (Trip
Edge) Snow Plows.
Two different brand motors are used on the
Quik-Lift® units, Fenner (single terminal) and Iskra.
The Iskra motors used in prduction could be either a
single terminal or a two terminal motor. Proper
identification of the brand and supplier part number is
necessary when seeking local parts and service
sources. Note: Brush Kits are the only replacement
part available thru Meyer Products.
The motor with which a specific Quik-Lift® unit is
equipped can be identified by the distinctive
characteristics shown in figure 0-2.
Model Identification and Serial Number Location
Inclusion of the model number and serial number is
extremely important when writing up warranty claim
forms and product report forms for proper evaluation
and follow up.
FENNER
4-1/2" Dia.
The basic model number is located on the name plate
located as shown in Figure 0-1. To determine whether
it is the standard or “H” model, measure the dimension
shown in Figure 0-1. The serial number is located on
the bottom of the base or on the name plate.
ISKRA
Label 15829
AMJ4739 12V 1,6kw
E-60H = 8-7/8"
E-60 = 6-3/4"
NAME PLATE
4-1/2" Dia.
SINGLE and TWO TERMINAL
FIGURE 0-2
MAINTENANCE
The following maintenance information is intended as
a basic guide for providing the Quik-Lift® unit with the
proper service and care. Sustained heavy duty
operation or operating under adverse conditions may
necessitate more frequent servicing.
SERIAL NO.
General Maintenance
Cleanliness
The greatest enemy to any hydraulic system is dirt or
contamination. Therefore, cleanliness must be stressed
at the time of installation, servicing and repairing.
FIGURE 0-1
-2-
Vehicle Electrical System
Maximum performance and efficiency of the Quick-Lift®
unit requires that the vehicle’s electrical system be
properly maintained and consist of:
Battery ----------Alternator ------
FILLER PLUG
FILTER
70 Amp. Hr. Minimum or
550 Cold Cranking Amps.
60 Amp. Minimum
GROUND
Check Regularly
DRAIN
PLUG
1. Battery Terminals - Must be clean and free of
corrosion.
2. Electrical Connections - Must be free of corrosion
and tight.
3. Battery - Must be in first-class condition.
4. Alternator (or Generator) and Regulator - Must be
functioning to specifications.
5. Hydraulic Fluid Reservoir Level - A significant drop
in hydraulic fluid level indicates a leak which must
be located and corrected. Insufficient hydraulic fluid
may result in severe damage.
FILTER
LOWER
ADJUSTMENT
SCREW
FIGURE 0-3
POST-SEASON MAINTENANCE
Meyer Hydraulic Fluid M-1.
Meyer Hydraulic Fluid M-1 is a specially formulated
mineral oil which maintains an almost constant
viscosity from normal to sub-zero temperatures.
Because it remains free flowing at extremely low
temperatures, the performance and efficiency are not
affected.
Refill Quick-Lift® unit with M-1 Fluid by fully retracting
lift rod (Ram) and filling reservoir to 1-1/2 “ below the
filler hole. Fill and bleed hoses and Power Angling
cylinders by loosening hydraulic fittings at cylinders
until they leak. Power angle plow repeatedly from one
side to the other until fluid flows steadily from the
leaking fittings while maintaining a constant check on
the reservoir fluid level.
Meyer Hydraulic Fluid M-1 also contains an additive
which neutralizes moisture accumulating in the fluid
due to condensation. It is effective for a maximum of
one year’s use.
Raise and lower the plow several times and with lift
rod fully retracted, give a final check to the fluid level
and replace filler plug.
Meyer Products will not be liable for damages
resulting from the use of inferior or other fluids or
oils.
Filters
Replacement of Hydraulic Fluid
Clean the two filters located in base of unit with mineral
spirits or equivalent and blow out with compressed
air. See Figure 0-3 for filter locations.
After a season’s use, completely drain the hydraulic
fluid (including hydraulic fluid in hoses and cylinders
on Power Angling models). Drain fluid through filler
hole shown in Figure 0-3 or drain hole in base by
completely retracting lift rod and unbolting unit to pour
fluid out or using a suction pump. Disconnect the
fittings at the Angling cylinders, completely retract the
cylinder rods and purge cylinders and hoses of all
hydraulic fluid. Flush the complete system including
unit, hoses and Power Angling rams with a non wax
(Napthenic) cleaner. If kerosene (Parrafinic) is used to
flush the system, the system must be flushed again to
remove any kerosene with a (Napthenic) based cleaner
that is wax free .
Protection Against Rust and Corrosion
When the Quik-Lift® unit is not used for extended
periods, protect the chromed lift rod (Ram) by fully
extending it and coating it with chassis lubricant. Full
extension of the lift rod (Ram) fills the cylinder with
hydraulic fluid. Coat the exposed portions of the Power
Angling cylinder rods (Rams) with chassis lubricant to
protect them against rust and corrosion.
-3-
SECTION 1
- GENERAL DESCRIPTION AND THEORY OF OPERATION
CONTENTS
GENERAL DESCRIPTION .................................................................................................
5
THEORY OF OPERATION .................................................................................................
5
FUNCTIONS ..................................................................................................................
5
•• Model E-60 ........................................................................................................
5
•• Model E-60H ......................................................................................................
5
•
•
ELECTRICAL AND FLOW CHARTS ...................................................................................... 6-13
QUIK-LIFT® UNIT COMPONENTS ..................................................................................
•
14
MOTORS ......................................................................................................................
14
•• Fenner ................................................................................................................
14
•• Iskra ....................................................................................................................
14
•
HYDRAULIC PUMP ..........................................................................................................
14
•
PRESSURE RELIEF VALVE ................................................................................................
14
•
SOLENOID VALVES .........................................................................................................
15
•• Cartridge ............................................................................................................
15
•• Coil ......................................................................................................................
15
“A” Solenoid Valve .............................................................................................
15
“B” Solenoid Valve ............................................................................................
15
“C” Solenoid Valve ...........................................................................................
15
•
CHECK VALVES ..............................................................................................................
16
•
PILOT CHECK VALVE ......................................................................................................
16
•
CROSSOVER RELIEF VALVES ............................................................................................
16
•
SWITCHES ....................................................................................................................
17
•• ELECTRO-TOUCH PAD .............................................................................................
17
•• SOLENOID SWITCH ..................................................................................................
17
FILTERS .......................................................................................................................
17
•
-4-
GENERAL DESCRIPTION
THEORY OF OPERATION
Quik-Lift® unit is an electrically powered and electrically
controlled hydraulic mechanism specifically designed
for use with Meyer Snow Plows. In addition to raising
and lowering the plow hydraulically, the model E-60,
E-60H angles the plow hydraulically, left and right, via
remote hydraulic cylinders.
FUNCTIONS
The Quik-Lift® models perform basic functions.
Models E-60 and E-60H
The four basic functions performed are:
•
•
•
•
The Quik-Lift® unit consists of a specially designed
high torque 12-volt DC motor which is directly coupled
to a gear-type hydraulic pump. The pump obtains its
supply of hydraulic fluid from an integral reservoir which
totally surrounds the integral hydraulic cylinder which
raises and lowers the plow.
Raise snow plow
Lower snow plow
Angle snow plow to right
Angle snow plow to left
Refer to pages 6 thru 13 for electrical and hydraulic
flow chart for each function. Each figure explains which
component is actuated and related in each function.
Included in all models is an electrically controlled and
powered solenoid valve cartridge “A” which is
energized to allow the plow to lower by gravity.
RAISE
The models E-60 & E-60H include an integral valve
body which contains two additional electrically
controlled solenoid valve cartridges. Solenoid valve
cartridge “B” is energized to route the pressurized
hydraulic fluid to the integral hydraulic cylinder to raise
the plow. Solenoid valve cartridge “C” is energized to
route the pressurized hydraulic fluid to the left remote
hydraulic cylinder to angle the plow to the right. Angling
the plow to the left only requires energizing the electric
motor since the normal route for the pressurized
hydraulic fluid is to the right remote hydraulic cylinder.
LEFT
RIGHT
LOWER
Additional components which control and supply
electrical current to the Quik-Lift® unit are an operator
controlled touch pad; a solenoid switch to supply high
amperage current to the unit’s motor; a wiring harness
to distribute low amperage current between the toggle
switch or switches, motor solenoid and the solenoid
valve cartridge(s); and short heavy gauge cables to
distribute high amperage current directly from the
positive terminal of the vehicle’s battery and ground
the unit directly to the negative terminal of the vehicle’s
battery.
Float Light
Over Load Light
The current 22154 Electro-Touch Control has been
redesigned. The Touch Pad now has raised buttons
and its circuitry has been changed from analog to
digital, functions have not changed. For
troubleshooting for power at the solenoids do not
disconnect wires. To check for power, prick the wire
through the insulation for testing.
This Electro-Touch Control knows when a short or an
open connection occurs and will go into overload
mode for the function being activated. To reset the
Touch Pad turn the switch on and off. The
Electro-Touch Control will not operate if not wired
properly as per the installation instructions Forms
1-690 or 1-759.
-5-
-6-
PO
S
Y
ER
TT
BA
G
NE
FUSE
PANEL
GROUND
SWITCH GROUND
ORANGE WIRE
WHITE
WIRE
10A
POWER TO SWITCH
BLUE WIRE
ON / OFF
SWITCH
RED
IMPORTANT:
The power lead (blue wire with fuse) should be connected to a
terminal on fuse panel that is HOT ONLY when the ignition switch is
in the “ON” position.
CAUTION:
When the snow plow is not in operation, the Electo-Touch® control
switch should be in the “OFF” position.
When the Electro-Touch® control switch is powered up, yellow lights
illuminate the location of the individual arrows for the function of the
snow plow: Up, Left, Right and Down.
RAISE E-60 and E-60H
B
1
4
3 6
2 5
GROUND
(ORANGE WIRE)
POWER TO SWITCH
(BLUE WIRE)
TO MOTOR SOLENOID
(WHITE WIRE)
POWER
E-60 AND E-60H
RAISE
END OF TOUCH PAD HARNESS
TO "A" SOLENOID
(BLACK WIRE)
TO "C" SOLENOID
(GREEN WIRE)
TO "B" SOLENOID
(RED WIRE)
“B” SOLENOID
Electrical power is sent to this solenoid by the “RED” wire. This solenoid,
when energized, directs hydraulic fluid to the lift cylinder.
NOTE: See illustration below for proper location of “B” Solenoid on the lift
unit.
MOTOR SOLENOID
Electric power is sent to this solenoid by the WHITE wire. This wire connects
to the small terminal on the motor solenoid. This wire activates the solenoid
switch, allowing electrical power from the vehicle battery to pass through the
solenoid to the lift motor via cables.
NOTE: Motor Solenoid must have a good ground to operate properly.
When the Up arrow is activated, electric power is sent to both the MOTOR &
“B” Solenoid via wiring harness.
-7-
FILTER
PUMP OPERATING
PRESSURE
RELIEF VALVE
2500 P.S.I.
LIFT
CYLINDER
RESERVOIR
PUMP
CHECK
VALVE
E-60 AND E-60H
RAISE FLOW CHART
B
C
LOWER ADJUSTMENT
PILOT
CHECK
VALVE
"B" SOLENOID
ENERGIZED
P.A. VALVE BLOCK
A
CROSS-OVER
RELIEF VALVE
3800 P.S.I.
+/- 400 P.S.I.
RETURN
PRESSURE
-8-
PO
S
G
TT
BA
NE
FUSE
PANEL
ER
Y
GROUND
SWITCH GROUND
ORANGE WIRE
WHITE
WIRE
10A
POWER TO SWITCH
BLUE WIRE
BLACK
ON / OFF
SWITCH
IMPORTANT:
The power lead (blue wire with fuse) should be connected to a
terminal on fuse panel that is HOT ONLY when the ignition switch is
in the “ON” position.
CAUTION:
When the snow plow is not in operation, the Electo-Touch® control
switch should be in the “OFF” position.
When the Electro-Touch® control switch is powered up, yellow lights
illuminate the location of the individual arrows for the function of the
snow plow: Up, Left, Right and Down.
LOWER / FLOAT E-60 and E-60H
A
1
4
3 6
2 5
GROUND
(ORANGE WIRE)
POWER TO SWITCH
(BLUE WIRE)
TO MOTOR SOLENOID
(WHITE WIRE)
POWER
E-60 AND E-60H
LOWER / FLOAT
END OF TOUCH PAD HARNESS
TO "A" SOLENOID
(BLACK WIRE)
TO "C" SOLENOID
(GREEN WIRE)
TO "B" SOLENOID
(RED WIRE)
Note: The rate (speed) at which the snow plow is lowered is adjustable.
Turning the Lower Adjustment Screw in (clockwise) will decrease the speed
at which the plow is lowered by gravity, and turning the screw out (counterclockwise) will increase the rate.
When the DOWN arrow is activated, electric power is sent only to the “A”
Solenoid via wiring harness. Electrical power is sent to this solenoid by the
BLACK wire. This wire connects to the BLACK wire on the “A” Solenoid.
Lowering of the snow plow an inch at a time is possible by tapping the down
arrow in short intervals. Holding down the down arrow will activate the float
light located on the upper left of the Electo-Touch® control switch. This light
indicates the snow plow is now in the Lower / Float position. In this position
the snow plow will be able to follow the contour of the road and the snow
plow can also be angled left or right. Touching the Up arrow on the touch
pad automatically cancels the Lower / Float position. Turning off the ignition
switch or the touch pad will reset the switch.
-9-
FILTER
PUMP OPERATING
PRESSURE
RELIEF VALVE
2500 P.S.I.
LIFT
CYLINDER
RESERVOIR
PUMP
CHECK
VALVE
E-60 AND E-60H
LOWER / FLOAT
FLOW CHART
B
LOWER ADJUSTMENT
"A" SOLENOID
IS ENERGIZED
PILOT
CHECK
VALVE
C
P.A. VALVE BLOCK
A
CROSS-OVER
RELIEF VALVE
3800 P.S.I.
+/- 400 P.S.I.
RETURN
PRESSURE
-10-
PO
S
G
TT
BA
NE
FUSE
PANEL
ER
Y
GROUND
SWITCH GROUND
ORANGE WIRE
WHITE
WIRE
10A
POWER TO SWITCH
BLUE WIRE
PRESSURE
ON / OFF
SWITCH
IMPORTANT:
The power lead (blue wire with fuse) should be connected to a
terminal on fuse panel that is HOT ONLY when the ignition switch is
in the “ON” position.
CAUTION:
When the snow plow is not in operation, the Electo-Touch® control
switch should be in the “OFF” position.
When the Electro-Touch® control switch is powered up, yellow lights
illuminate the location of the individual arrows for the function of the
snow plow: Up, Left, Right and Down.
ANGLE LEFT E-60 and E-60H
1
4
3 6
2 5
GROUND
(ORANGE WIRE)
POWER TO SWITCH
(BLUE WIRE)
TO MOTOR SOLENOID
(WHITE WIRE)
RETURN
POWER
E-60 AND E-60H
ANGLE LEFT
END OF TOUCH PAD HARNESS
TO "A" SOLENOID
(BLACK WIRE)
TO "C" SOLENOID
(GREEN WIRE)
TO "B" SOLENOID
(RED WIRE)
“B” and “C” SOLENOIDS
Electrical power is not sent to either of these solenoid. The “C” Solenoid,
when NOT energized, directs the pressurized hydraulic fluid out of the hose
to the right (passenger-side) power angle cylinder.
MOTOR SOLENOID
Electric power is sent to this solenoid by the WHITE wire. This wire connects
to the small terminal on the motor solenoid. This wire activates the solenoid
switch, allowing electrical power from the vehicle battery to pass through the
solenoid to the lift motor via cables.
NOTE: Motor Solenoid must have a good ground to operate properly.
When the Left arrow is activated, electric power is sent only to the MOTOR
Solenoid via wiring harness.
-11-
FILTER
PUMP OPERATING
PRESSURE
RELIEF VALVE
2500 P.S.I.
LIFT
CYLINDER
RESERVOIR
PUMP
CHECK
VALVE
E-60 AND E-60H
ANGLE LEFT
FLOW CHART
B
LOWER ADJUSTMENT
PILOT
CHECK
VALVE
C
P.A. VALVE BLOCK
A
CROSS-OVER
RELIEF VALVE
3800 P.S.I.
+/- 400 P.S.I.
RETURN
PRESSURE
-12-
PO
S
G
TT
BA
NE
FUSE
PANEL
ER
Y
GROUND
SWITCH GROUND
ORANGE WIRE
WHITE
WIRE
10A
POWER TO SWITCH
BLUE WIRE
ON / OFF
SWITCH
RETURN
GREEN
IMPORTANT:
The power lead (blue wire with fuse) should be connected to a
terminal on fuse panel that is HOT ONLY when the ignition switch is
in the “ON” position.
CAUTION:
When the snow plow is not in operation, the Electo-Touch® control
switch should be in the “OFF” position.
When the Electro-Touch® control switch is powered up, yellow lights
illuminate the location of the individual arrows for the function of the
snow plow: Up, Left, Right and Down.
ANGLE RIGHT E-60 and E-60H
C
1
4
3 6
2 5
GROUND
(ORANGE WIRE)
POWER TO SWITCH
(BLUE WIRE)
TO MOTOR SOLENOID
(WHITE WIRE)
PRESSURE
POWER
E-60 AND E-60H
ANGLE RIGHT
END OF TOUCH PAD HARNESS
TO "A" SOLENOID
(BLACK WIRE)
TO "C" SOLENOID
(GREEN WIRE)
TO "B" SOLENOID
(RED WIRE)
“C” SOLENOID
Electrical power is sent to this solenoid by the “GREEN” wire. The “C” Solenoid, when energized, directs the pressurized hydraulic fluid out of the coupler to the left (driver-side) power angle cylinder.
Note: See illustration below for proper location of “C” Solenoid on the
lift unit.
MOTOR SOLENOID
Electric power is sent to this solenoid by the WHITE wire. This wire connects
to the small terminal on the motor solenoid. This wire activates the solenoid
switch, allowing electrical power from the vehicle battery to pass through the
solenoid to the lift motor via cables.
NOTE: Motor Solenoid must have a good ground to operate properly.
When the Right arrow is activated, electric power is sent to the MOTOR &
“C” Solenoid via wiring harness.
-13-
FILTER
PUMP OPERATING
PRESSURE
RELIEF VALVE
2500 P.S.I.
LIFT
CYLINDER
RESERVOIR
PUMP
CHECK
VALVE
E-60 AND E-60H
ANGLE RIGHT
FLOW CHART
B
C
LOWER ADJUSTMENT
PILOT
CHECK
VALVE
"C" SOLENOID
ENERGIZED
P.A. VALVE BLOCK
A
CROSS-OVER
RELIEF VALVE
3800 P.S.I.
+/- 400 P.S.I.
RETURN
PRESSURE
QUIK-LIFT® UNIT COMPONENTS
MOTORS ( 4-1/2”) E-60, E-60H
The basic operating principles of the hydraulic pump
used in the Quik-Lift® units are quite simple. Figure
1-1 illustrates the basic components of a positive
displacement gear type pump and their functions. The
pumping action takes place within the pump chamber
which is connected to the reservoir by the intake line.
The pump chamber has an outlet line in which the liquid
under motion and pressure leaves the pump to perform
work.
The 12-volt DC high torque motor used on the
Quik- Lift® units are interchangeable among all three
models. Its function in all three applications is to drive
the hydraulic pump. The motor is only energized and
operating when pressurized hydraulic fluid is required.
Two different brand motors were used. While they are
interchangeable and have nearly identical performance
characteristics, they have distinctive design differences.
PRESSURE RELIEF VALVE
Fenner
A basic pressure relief valve is shown in
Figure 1-2. It consists of a poppet valve and a valve
spring. Both are located in a passage which connects
the inlet passage to the outlet passage. The poppet
valve is normally held closed by the valve spring,
sealing the connecting passage from the pressurized
outlet passage. The poppet valve, being a ball, is
exposed to the pressurized hydraulic fluid in the outlet
passage. Whenever the hydraulic pressure against the
poppet valve becomes greater than the pressure being
exerted on the poppet valve from the opposite
direction by the valve spring, the poppet valve will
open. This allows some of the pressurized hydraulic
fluid to flow through the connecting passage to the
non pressurized inlet passage. The effect is to lower
the pressure in the outlet passage which will allow the
valve spring to close the poppet valve again. Under a
condition, such as when a hydraulic cylinder is
extended to the end of its stroke, eliminating additional
space for the pressurized hydraulic oil to be pumped
into, the alternate opening and closing of the poppet
valve controls the pump’s pressure output and provides
an escape for the pressurized hydraulic fluid.
The Fenner motor is a four pole electro magnet motor
which consists primarily of a 4-1/2” diameter solid steel
frame (coated to resist corrosion), armature, brushes,
field coils and pole pieces. This motor can be used on
vehicles with either the common negative ground
electrical system or the positive ground electrical
system.
Iskra - Single and Two terminal
The Iskra motor is a four pole, electromagnet motor
which consists primarily of a 4-1/2" diameter solid steel
frame, armature, brushes, field coils and pole pieces.
This motor can be used on vehicles with either the
common negative ground electrical system or the
positive ground electrical system.
HYDRAULIC PUMP
The pump in a hydraulic system employs an external
source of power to apply a force to a liquid. A pump
develops no power of its own. It simply transfers power
from an external source (the electric motor on the
Quik-Lift® unit) to the liquid in the hydraulic system.
The pressure relief valve used in the Quik Lift® pump,
while more sophisticated than the one described,
functions in the same manner. The pump pressure relief
valve may be set by adjusting the set screw after
installing a suitable pressure gauge of 3000 P.S.I. in
the circuit. See Specifications on page 53.
E-60 with
1-1/4" Lift Ram
OPENS AT
2500 + 50 P.S.I.
RESERVOIR
Lift Cylinder
Full Stroke
E-60 with
1-3/4" Lift Ram
OPENS AT
2000 + 50 P.S.I.
ELECTRIC
MOTOR
W
O
FL
INTAKE LINE
DRIVEN GEAR
W
O
FL
PUMP CHAMBER
DRIVE GEAR
Reservoir
Pressure from
the Pump
OUTLET LINE
PUMP HOUSING
SUMP BASE
FIGURE 1-2
FIGURE 1-1
-14-
QUIK-LIFT® UNIT COMPONENTS CONT.
SOLENOID VALVES
“A” Solenoid Valve
Hydraulic valves are simple in concept and all have
the same basic function: Control the direction of oil
flow. Three types of Solenoid Valve is used on the
models E-60, E-60H.
The “A” Solenoid Valve is used in the E-60 and E-60H.
These Cartridges contains a poppet valve whose static
or de-energized position is closed. Its energized
position is open.
Each Solenoid Valve consists of two components: the
Cartridge and the Coil.
On both models, the “A” Solenoid Valve retains
hydraulic fluid in the lift cylinder. It is energized
(opened) to allow the hydraulic fluid to flow from the
lift cylinder back to the reservoir, enabling the plow to
lower by gravity.
Cartridge
The Cartridge consists of the hydraulic valve
mechanism and an armature which enables the
valve mechanism to be operated and controlled
electrically. The Cartridge is designed to screw in
and out of the Quik-Lift® units much like the typical
“spark plug”.
The “A” Solenoid Valve is designed to remain energized
(open) while the plow is lowered, plowing snow. This
is the “float” feature which insures that the plow
maintains contact with the ground contour.
“B” Solenoid Valve
Coil
The “B” Solenoid Valve is used on the Quik-Lift® models
E-60 and E-60H. The “B” Cartridge contains a spool
valve whose static (de-energized) position allows the
pressurized hydraulic fluid to flow to the
“C” Solenoid Valve. In the energized position, the
pressurized hydraulic fluid is diverted to the lift cylinder,
raising the plow.
The Coil is the electrical component which operates
the Cartridge’s valve mechanism by producing
magnetism which pulls the Cartridge’s armature
toward it. Since the armature is connected to the
valve mechanism’s only moving part, it is pulled
by the armature.
Figure 1-3 illustrates the typical Coil. Whenever
electrical current flows to the Coil, it flows through
the winding, which consists of numerous turns of
copper wire. The flow of current through the
winding produces a magnetic field which pulls the
soft iron armature further into the Coil.
“C” Solenoid Valve
The “C” Solenoid valve is used on the Quik-Lift® models
E-60 and E-60H. The “C” Cartridge contains a spool
valve whose static (de-energized) position allows the
pressurized hydraulic fluid to flow to the right power
angling cylinder which angles the plow to the left. At
the same time, it allows the hydraulic fluid being forced
from the retracting left power angling cylinder to flow
through the “C” Cartridge back to the reservoir.
The armature pulls the valve spool or poppet valve
into its alternate (energized) position. Not illustrated
is an integral coil spring, which is compressed
when the armature is pulled by the magnetism.
In the energized position, the pressurized hydraulic
fluid is diverted to the left power angling cylinder,
angling the plow to the right. Also, the hydraulic fluid
being forced from the retracting right power angling
cylinder flows through the “C” Cartridge back to the
reservoir.
When the current flow ceases, the magnetic field
disappears and the compressed coil spring pushes
the armature back to its original (de-energized)
position.
WINDING
COIL
VALVE SPOOL
ARMATURE
FIGURE 1-3
-15-
QUIK-LIFT® UNIT COMPONENTS CONT.
CHECK VALVES
CROSSOVER RELIEF VALVE
Check valves are very simple devices that have two
basic functions: They prevent fluid from passing through
them in one direction, but they allow fluid to pass
through them in the opposite direction.
When plowing snow, a snow plow can be exposed to
damaging forces caused by impact with hidden
obstructions, ends of curbs, etc. With power angling,
these damaging forces can damage not only the snow
plow but also the vehicle. The crossover relief valve
has the function of protecting the snow plow system
against these damaging forces under normal snow
plowing conditions. The crossover relief valve, cannot
protect the system from damaging forces that are too
great due to abusive snow plowing conditions.
In both models a pump check valve is used to prevent
hydraulic fluid from leaking back through the pump to
the reservoir.
The E-60 and E-60H models incorporate two additional
check valves, necessary because the “B” and “C”
Solenoid Valves, being spool valves, have some
leakage.
Basically, the crossover relief valve functions exactly
like the previously described pump relief valve. It’s
designed to open at a specific pressure. In this instance,
the pressure is not produced by the pump but rather
by the damaging force. As an example, assume that
the right corner of the plow runs into the end of a curb.
The impact will attempt to collapse the right power
angling cylinder. As a result, very high hydraulic
pressure is produced within the cylinder. When the
produced pressure is high enough, it opens the
crossover relief valve, allowing the highly pressurized
hydraulic fluid to flow directly to the left power angling
cylinder.
One check valve is located between the “B” Solenoid
Valve and the lift cylinder. It prevents the hydraulic fluid
in the lift cylinder from leaking back through the “B”
Solenoid Valve which could cause the weight of the
plow to angle the plow to the left by forcing hydraulic
fluid through the “C” Solenoid Valve into the right power
angling cylinder.
The other check valve is located between the “B” and
“C” Solenoid Valves. It prevents the hydraulic fluid in
either power angling cylinder from being forced
through the “B” Solenoid Valve to the left cylinder.
When the crossover relief valve functions in this manner,
the excessive pressure is released, the excessive energy
produced by the impact is absorbed, and the result is
only a change in angled position of the plow.
PILOT CHECK VALVE
The pilot check valve used only on the E-60 and
E-60H is more sophisticated in that it incorporates a
piston in addition to the ball, seat and spring. It is
located between the “C” Solenoid Valve and reservoir.
It has two functions: The first is to prevent the hydraulic
fluid in either power angling cylinder from leaking back
to the reservoir. The second is to allow the hydraulic
fluid from the retracting power angling cylinder during
the angling cycle to return to the reservoir. This is
accomplished by the pressurized hydraulic fluid
moving the piston which forces the check ball off its
seat.
The crossover relief valve may be adjusted to the
specified pressure of 3800 P.S.I. ± 400 by turning the
3/8” hex cap screw after installing a suitable pressure
gauge of 5000 P.S.I. in the circuit. TIGHTEN (TURN IN)
ADJUSTMENT SCREW TO INCREASE PRESSURE.
See Disassembly Figure 3-49 thru 3-56. Reassembly
figures 3-57 thru 3-69.
-16-
QUIK-LIFT® UNIT COMPONENTS CONT.
SWITCHES
SOLENOID SWITCH
Electro-Touch® Control Pad (E-60 and E-60H)
The Quik-Lift® motor requires more current or amperage
to operate than the vehicle wiring, vehicle ignition
switch or Touch Pad have the capacity to handle. The
solenoid switch is essentially a heavy duty switch with
the capacity to handle the heavy current required by
the motor. It is closed electrically by the solenoid to
convey the heavy current directly from the vehicle
battery via heavy gauge electrical cable. The solenoid,
which functions essentially the same as the previously
described solenoid valves, receives its low amperage
current at the proper times via the wiring harness. This
solenoid must be grounded to operate properly.
IMPORTANT:
The power lead to the switch should be connected to
a terminal on the fuse panel that is HOT ONLY when
the ignition switch is in the “ON” position.
When the control switch is powered up, yellow lights
illuminate the arrows of the individual functions. The
up arrow for raise, the left arrow for angle left, the right
arrow for angle right and the down arrow for lower or
float.
Holding the down arrow for a full second will activate
a light located in the upper left corner of the
Electro-Touch® switch. This light indicates the snow
plow is now in the float position. In this position the
snow plow will be able to follow the contour of the
road and the snow plow can also be angled to the left
or right. Touching the up arrow will automatically cancel
the float position.
FILTERS
This switch is short circuit, open circuit and temperature
protected. If any of these conditions exists, the
overload light will illuminate. The overload light is
located just below the float light in the upper left corner
of the Touch Pad. Reset is accomplished by cycling
the power to the Touch Pad via the on/off switch located
to the left of the cord as it enters the Touch Pad.
1. A high pressure filter on the pressure side of the
pump.
Cleanliness is perhaps the single most important
ingredient in assuring a hydraulic system’s reliability.
Should the hydraulic fluid become contaminated,
malfunction and permanent damage to the hydraulic
system may occur. For this reason, all the Quik-Lift®
units are equipped with a filter system consisting of:
2. A filter screen between the lift cylinder and “A”
Solenoid Valve
With this system, the hydraulic fluid is filtered as it
leaves the pump. Because clean hydraulic fluid is most
important to insure “A” Solenoid Valve reliability, the
hydraulic fluid leaving the lift cylinder is filtered before
passing through the “A” Solenoid Valve. The filter screen
and high pressure filter are easily removed for periodic
cleaning or replacement.
CAUTION:
When the snow plow is not in operation, the
Electro-Touch® Control Switch should be in the “OFF”
position.
NOTE: Additional filter screens are added to the
“A”, “B” and “C” Cartridge Valves.
IMPORTANT:
Should the hydraulic fluid become contaminated, it
will be necessary to replace all the hydraulic oil in the
system. The complete system (hydraulic unit, power
angling cylinders and hoses) should be flushed. Flush
the system with a non wax (Napthenic) cleaner. If
kerosene (Parrafinic) is used to flush the system, the
system must be flushed again to remove any kerosene
with a (Napthenic) based cleaner that is wax free. Refill
hydraulic system with Meyer M-1 oil.
-17-
SECTION 2
- DIAGNOSIS
CONTENTS
E-60 and E-60H
GENERAL INFORMATION ..............................................................................
19
TESTING TIPS .................................................................................................
19
“RAISE” Troubleshooting ...............................................................................
20
“LEAK DOWN” Troubleshooting ...................................................................
21
“LOWER” Troubleshooting ............................................................................
21
“ANGLE LEFT” Troubleshooting ....................................................................
22
“ANGLE RIGHT” Troubleshooting .................................................................
23
“WILL NOT HOLD ANGLE” Troubleshooting ..............................................
24
“CROSSOVER RELIEF VALVE” Flow Chart .................................................
24
-18-
DIAGNOSTIC FLOW CHART FOR
E-60, E-60H QUIK-LIFT® UNITS
These charts are intended to be used as an aid in diagnosing problems on the Quik-Lift® units. They are not a substitute for factory
training and experience. Be certain to read the General Information and Testing Tips sections before attempting any troubleshooting.
IMPORTANT: Maintenance and repairs must be performed with the moldboard on the ground.
General Information
Before any troubleshooting is started, make certain the following conditions are met.
1. The moldboard is pointing straight ahead. This can often be done by coupling the left cylinder into the right cylinder and
pushing the moldboard by hand.
2. The power angling cylinders must be installed correctly on to the A- frame. The left cylinder (Driver’s side) has a hose attached
with a male half of a coupler at the end; the right cylinder (Passenger side) has a hose attached with a female half of a coupler at
the end.
3. The solenoid coils must be on their proper valve. (See drawing below).
TESTING TIPS
Many tests do not require removing the Quik-Lift® unit from the vehicle. However, more thorough testing can be performed using the
Meyer Test Stand which allows direct pressure and amperage readings.
1.
Using a screwdriver or other small tool to check for magnetism of the solenoid coils “A”, “B” and “C”. Place the tool on the nut
securing the coil and have an assistant operate the switch. You should feel strong magnetic attraction.
Use a test light or volt meter to determine whether there is power at the harness or switch.
When determining AMP draw of the motor, always obtain the highest value possible, i.e, at maximum raise or maximum angle with
motor running.
Proper rotation for the 4-1/2” motor (Fenner/Iskra) is clockwise by looking at the motor shaft from the bottom of the motor.
The pump shaft of a good pump can be turned smoothly using two fingers. If it can’t be turn easily, the pump is too tight and
must be replaced.
Pump pressure can be measured at an angle hose (note pressure at full angle) or in the pressure filter port (an adaptor is
necessary for the filter port).
Flush the complete system including unit, hoses and power angling rams with a non wax (Napthenic) oil / cleaner. If kerosene
(Parrafinic) is used to flush the system, the system must be flushed again to remove any kerosene with a (Napthenic) based
oil / cleaner that is wax free.
2.
3.
4.
5.
6.
7.
FUSE
PANEL
The current 22154 Electro-Touch Control has been redesigned.
The Touch Pad now has raised buttons and its circuitry has been changed
from analog to digital, functions have not changed. For troubleshooting for
power at the solenoids do not disconnect wires. To check for power, prick
the wire through the insulation for testing. The Electro-Touch Control knows
when a short or an open connection occurs and will go into overload mode
for the function being activated. To reset the Touch Pad turn the switch on
and off. The Electro-Touch Control will not operate if not wired properly as
per the installation instructions (1-690 & 1-759).
POWER TO SWITCH
BLUE WIRE
ON / OFF
SWITCH
10A
TO "A" SOLENOID
(BLACK WIRE)
TO "C" SOLENOID
(GREEN WIRE)
TO "B" SOLENOID
(RED WIRE)
WHITE
WIRE
SWITCH GROUND
ORANGE WIRE
NE
PO
3 6
2 5
1
4
GROUND
(ORANGE WIRE)
POWER TO SWITCH
(BLUE WIRE)
TO MOTOR SOLENOID
(WHITE WIRE)
END OF TOUCH PAD HARNESS
G
S
TT
BA
Y
ER
POWER
GROUND
RED
A
GREEN
B
C
BLACK
-19-
E-60 & E-60H
E-60 AND E-60H
SNOW PLOW WILL NOT RAISE
NO
Does the Motor
Operate?
Is there power
going to
the motor?
YES
Charge Battery Clean and tighten
all electrical
Connections.
YES
NO
Remove motor.
Does motor run when
12 volts is applied?
Inspect Motor Armature, Brushes
Repair or Replace
Motor as necessary
NO
YES
YES
NO
Are all electrical
connections clean
and tight?
Is Battery Charged?
NO
Can the pump
shaft turn by
hand?
NO
YES
Is Ground Cable
attached to the
Negative (-)
Battery Terminal?
Is there power
leaving the
switch?
Check switch
for Continuity
NO
Is there power
going to the
motor solenoid,
at White Wire?
Check Wires at
Molded connector.
YES
YES
Replace the
Wiring
Harness.
Replace the
Motor
Solenoid.
YES
NO
YES
Replace pump.
NO
Is the fluid level
1-1/2" below
filler hole?
NO
Is the Fuse
OK?
Replace Fuse.
Check for short
in Harness,
"B" Coil, Switch
Connections,
Motor Solenoid,
Electric Motor.
Replace the
Touch
Pad
ADD M-1
Fluid
YES
Does the snow plow
angle to the left
instead of raising?
NO
Does the snow plow
angle when the
Angle Switch
is activated?
NO
Is there pressure
(or flow) at the
Filter port?
NO
Are the
Filters
Clogged?
NO
NO
Is the motor turning
the proper direction?
Check Brushes for
proper installation or
replace motor.
YES
YES
YES
Is the "A" Valve
stuck in the
open position?
YES
Clean
or
Replace
Filters.
NO
Replace
the
Pump.
YES
Clean or Replace
"A" Valve.
-Retest Does snow plow
raise?
NO
Disassemble unit Inspect O-rings,
Cylinder,Piston
assembly.
Look for blockage
in Sump Casting
passages.
NO
Can pump relief
pressure be adjusted
to 2000 P.S.I.
Is the pump
shaft turning
tightly?
NO
Does the motor
armature turn
tightly?
YES
YES
Replace
the
Pump.
Is there power to
the "B" Coil?
(Red Wire)
at Harness
NO
Does the "B" Coil
(Red Wire) have
magnetism?
NO
YES
YES
YES
Are the "B" Valve
O-Rings in good
Condition?
NO
Replace
O-Rings.
Replace
the wiring
harness.
Replace
"B" Coil.
YES
Clean or
Replace the
"B" Valve
and retest.
NO
Replace P.A. Block
with E-46 plate and
retest. - Does snow
plow Raise now?
NO
Is there power
leaving the switch
at the red wire?
Replace
Sump Base.
YES
Replace
P.A. Block
-20-
NO
Repair or Replace
the motor.
Are wires in
molded connector
making contact
with the switch?
YES
Replace
Touch Pad
E-60 AND E-60H
SNOW PLOW LEAKS DOWN
Does the
snow plow drop
straight down?
NO
Does the snow plow
drop and angle
to the left?
YES
YES
Replace
"B" Check Valve
Does it now hold?
Are "A" Valve O-rings
in good condition?
Does "A" Valve stem
move freely?
YES
NO
NO
Dissasemble unit
Inspect O-Rings,Cylinder,
Piston Assembly.
Does it hold now?
NO
Replace
"B" Valve
Does it now hold?
NO
Replace
Sump Base
Replace O-Rings
Replace "A" Valve
Dissasemble unit
Inspect O-Rings,Cylinder,
Piston Assembly.
Does it hold now?
NO
Replace
Sump Base
NO
Replace
Sump Base
SNOW PLOW WILL NOT LOWER
Does "A" Coil
(Black Wire) have
magnetism?
NO
Is there power to the
"A" Coil (Black Wire)
at harness?
NO
YES
YES
YES
Is there power leaving
the switch at the
Black Wire?
Replace
"A" Coil
Replace
Harness
NO
Is the Touchpad
plugged in completely?
YES
Is Fuse
OK?
YES
Replace "A" Valve
Does it now lower?
NO
Check for a clogged
filter or a blocked
passageway.
(Lower Adj. Screw)
NO
Check for Bent or
Siezed Ram
Assembly.
-21-
Replace
Touch Pad
NO
Replace the fuse Check for short in
harness, "A" Coil,
Plug connections.
E-60 AND E-60H
SNOW PLOW WILL NOT ANGLE LEFT
NO
Can the snow plow
Raise?
See the Raise
Flow Chart
Section
YES
Does the motor run
when angle switch
is pushed?
NO
Is there power to
the motor solenoid?
(White Wire)
NO
NO
Is there power
leaving the switch?
Is the Touchpad
plugged in completely
YES
YES
YES
Does the snow plow
raise instead of
angling left?
YES
Clean or replace the
"B" Valve.
Retest
Replace
Touch Pad
Replace Harness
NO
Does the snow plow
angle to the right
the angle left
switch is pushed?
NO
YES
Clean or replace the
"C" Valve.
Retest
Is the ampere draw
less than 100 amps
while trying to angle
snow plow?
NO
YES
NO
NO
Replace
Piston
YES
Will the snow plow angle
right & left if not allowed
to travel to extreme
angled position?
NO
Does pressure remain
in angle hose
when the motor
is not running?
YES
NO
Replace
O-Rings
YES
YES
Clean or replace
the Crossover Relief.
Does the snow plow
now angle?
Relieve the interference
between the
Sector and A-Frame.
YES
Is the Pilot piston in
good condition?
(worn/sloppy or missing)
Are "C" Valve
O-Rings in good
condition?
NO
Can the snow plow be
angled by hand when the
P.A. Rams are disconnected
from A-Frame?
NO
Replace the
P.A. Block
If both hoses are stiff If one hose is stiff
inspect the Pilot Check inspect the the "C"
Piston and "C" Valve
valve for binding.
for binding.
Replace Coupler sets.
Temporarily put 1/2" blocks
between the Sector and
A-Frame to limit the degree
of angle. Will the snow plow
now angle?
YES
Weld
1-1/2" x 1-1/2" x 1/2"
spacers to the A-Frame
stops.
-22-
NO
Replace both the
Coupler sets and/or
clean or replace the
"C" Valve.
E-60 AND E-60H
SNOW PLOW WILL NOT ANGLE RIGHT
Can the snow plow
Raise?
NO
See the Raise
Flow Chart
Section
YES
Does the motor run
when angle switch
is pushed?
NO
Is there power to
the motor solenoid?
(White Wire)
NO
Is there power
leaving the switch?
NO
YES
YES
YES
Replace
Touch Pad
Replace Harness
Does the snow plow
raise instead of
angling left?
YES
Clean or replace the
"B" Valve.
Retest
Are the wires in
molded connector
making contact with
the switch?
NO
Can the snow plow
angle to the Left?
YES
Does the "C" Coil
have magnetism?
(Green Wire)
NO
Is there power to
the "C" Coil?
(Green wire at harness)
NO
YES
YES
Are "C" Valve
O-Rings in good
condition?
YES
Replace the
"C" Coil.
Retest
NO
Is there power
leaving the switch?
Replace Harness
Replace
O-Rings
YES
Clean or replace
the Crossover Relief.
Does the snow plow
now angle?
Replace both the
Coupler sets and/or
clean or replace the
"C" Valve.
-23-
NO
Replace the
P.A. Block
NO
Are the wires in
molded connector
making contact with
the switch?
YES
Replace
Touch Pad
E-60 AND E-60H
SNOW PLOW WILL NOT HOLD ANGLE
Are the Rams mushy?
Can you push the moldboard
6" to 8" by hand?
NO
Does the moldboard
hold left angle & release
from right angle?
NO
YES
Bleed air from the system
and snug up gland nuts.
Check couplers and fittings
for leaks.
Are the "C" Valve
O-Rings in poor
condition?
NO
NO
Set Crossover Relief to
3800 + 400 P.S.I.
Replace Crossover O-Rings
or complete Crossover.
Replace the
P.A. Block
Replace O-Rings
Inspect "C" Valve O-rings
Change if necessary. Does
snow plow now angle?
NO
YES
YES
YES
Is Crossover Relief set
at 3800 + 400 P.S.I.?
Are Crossover O-Rings
in good condition?
Change Pilot Check
Ball and Seat.
does snowplow
now hold?
NO
Inspect Crossover Relief.
(Rebuild or Replace)
Does snow plow now
hold angle?
NO
Replace the
P.A. Block
Crossover Relief Valve
"C"
SOLENOID
"B"
SOLENOID
Pressure
CHECK
VALVE
POWER ANGLING
CYLINDERS
PILOT
CHECK
CROSSOVER
RELIEF
3800 + 400 P.S.I
-24-
SECTION 3 -
REPAIR PROCEDURES
CONTENTS
QIUK-LIFT ®
Parts List ...........................................................................................
26
Exploded View ................................................................................
27
GENERAL INFORMATION
28
UNIT DISASSEMBLY AND REASSEMBLY ......................................
28
Disassembly ....................................................................................
28
Photos .............................................................................................. 29-38
Reassembly .....................................................................................
39
• Additional Reassembly Points ...................................................
28
Photos .............................................................................................. 39-40
PUMP .................................................................................................
28
Shaft Seal Replacement ................................................................
28
Pump Disassembly ......................................................................... 30-31
Pump Reassembly .......................................................................... 47-48
CROSSOVER RELIEF VALVE
Disassembly .................................................................................... 41-42
Reassembly ..................................................................................... 43-46
VALVE CARTRIDGE INFORMATION “A”, “B” & “C” ...................
50
“A” Cartridge ....................................................................................
50
“B” & “C” Cartridges ......................................................................
50
BRUSH REPLACEMENT ....................................................................
51
Iskra Brush Replacement ..............................................................
51
Fenner Brush Replacement ..........................................................
51
SPECIAL TOOLS .................................................................................
52
SPECIFICATIONS ............................................................................
53
-25-
PARTS & INSTALLATION INSTRUCTIONS
E-60 & E-60H QUIK LIFT®
PARTS LIST
STANDARD- LONG STROKEUP THROUGH
MDII
C-9
HM-9 & HM-10
STANDARD- LONG STROKEUP THROUGH
MDII
C-9
HM-9 & HM-10
ITEM 1-1/8" x 6" Stroke
E-60
1
2
2
3
4
5
6*
7*
8
9
10
11*
12*
13
14
15
16
17
18
19*
20*
21a*
21b*
22
23
24*
25
26
27
28
29
30
31
32
33
34*
35
36
37
38*
39
40
41*
42
43
44
45
46*
47a*
47b*
48
49a
49b
50
51
52*
53
54
55
*
15726
15706
15335
15208
15158
15219
15162
15125
20316
15738
05119
15131
15737
08473
21805
21806
15696
15953
15209
15198
15131
15693
20697
15708
21929
22129
15641
15619
21999
15695
15729
15688
15713
15574
15124
15354
15603
15604
15700
15702
15699
15701
22118
15703
22119
21083
15122
15123
15124
15841
15730
15831
22120
15686
15687
15661
15659
15660
15431
1-1/8" x 8" Stroke
QTY.
ITEM 1-1/8" x 6" Stroke
E-60
DESCRIPTION
E-60H
15726
15336
15206
15158
15219
15162
15125
15760
20316
15738
05119
15131
15737
08473
21805
21806
15704
15205
15209
15198
15131
15163
20697
15709
21929
22129
15641
15619
21999
15729
15688
15713
15574
15124
15354
15603
15604
15700
15702
15699
15701
22118
15703
22119
21083
15122
15123
15124
15841
15730
15831
22120
15686
15687
15661
15659
15660
15431
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
3
5
1
2
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
1
1
2
1
1
1
1
1
1
Base & Tank Assembly
• Sump Base
• Ram Assy. SEE ILLUSTRATION
• Ram Assembly 1-3/4”
•• Ram
•• Piston
•• Piston Follower
•• Packing Cup
•• O-ring 7/16" I.D.
•• Spacer
•• Locknut 1/2-13
• Cover & Seal Assembly
•• Wiper
•• O-ring 3-1/2" I.D.
•• Sleeve
• Pressure Relief Valve Kit
•• Reducer Bushing 1/4-1/8
•• Pressure Relief Valve
• Cylinder Tank
• Cylinder
• Washer
• O-ring 1-1/8 I.D.
• O-ring 3-1/2 I.D.
• O-ring 1-1/2 I.D.
• O-ring 1-15/16 I.D.
• Locknut 5/16-24
• Stud
• Washer, Nyltite 5/16
• Plug w/O-ring 9/16"
• Filter Kit 9/16"
•• Filter
•• Plug w/O-ring 9/16"
• Spacer Ring
• Pump
• Dowel Pins
• Locator
• Pump Check Valve
•• O-ring 3/8 I.D.
•• Seat
•• Ball 9/32
•• Spring
• O-ring 3/8 I.D.
• Ball Seat
• Relief Valve
• O-ring "Special"
• Socket Set Screw
• Pump Mounting Plate
• Bolt 3/8-16 x 3-1/4" Gr. 5
• Star Washer 3/8
• O-ring 1/4 I.D.
• O-ring 5/16 I.D.
• O-ring 3/8 I.D.
• Motor - Two Terminal
• Cover/Motor Mount
• Cover/Motor Mount w/tabs
• Cap Screw 5/16 x 3-1/4"
• Pump Shaft Seal
• O-ring 4-3/4 I.D.
• "A" Solenoid Assembly
•• "A" Coil, Black Wire
•• "A" Cartridge Valve
•• Seal Kit, "A" Valve
53a
54a
55a
56
*
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
*
76
77
78
79
80
81
82*
83
84
85
*
86
87
88
*
89
90
91
92
1-1/8" x 8" Stroke
QTY.
DESCRIPTION
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
• "A" Solenoid Assembly
•• "A" Coil, Black Wire
•• "A" Cartridge Valve
•• "A" Coil Nut
•• Seal Kit, "A" Valve
• VALVE ASSY w/COUP.
•• Forged 90 Degree Elbow
•• Coupler, Male Half Low Spill
•• Coupler, Female Half Low Spill
• Kit-Crossover Valve
•• O-ring
•• O-ring
•• Cage
•• O-ring w/Glyd. Ring
•• Poppet
•• Washer
•• Guide
•• Spring
•• Spacer
•• Disc
•• Plug
•• Adj. Screw
•• O-ring
•• Acorn Nut 9/16-18
•• Seal Kit-Crossover Valve
(includes items 62,63,65,74)
• Kit-Pilot Check Valve
•• Ball, Steel
•• Spring
•• Plug
• Piston
• Plug Valve Block
•• O-ring 9/16 I.D.
• "B" Solenoid Assembly
•• "B" Coil, Red Wire
•• "B" Cartridge Valve
••• Seal Kit-"B" Cartridge
• "C" Solenoid Assembly
•• "C" Coil, Green Wire
•• "C"-Cartridge Valve
••• Seal Kit-"C" Cartridge
• Kit-"B" Solenoid Check Valve
•• Ball, 7/16
•• Spring
• Scr., Soc. Head 5/16-18 x 1-1/2"
E-60H
15972
15905
15660
22435
15431
15758
22295
22293
22294
15606
15972
15905
15660
22435
15431
15758
22295
22293
22294
15606
15610
15610
15639
15639
15609
15359
15126
15697
15382
15698
15432
15358
15430
15381
15433
15576
15609
15359
15126
15697
15382
15698
15432
15358
15430
15381
15433
15576
21826
21826
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
NOTES:
Parts indented are included in assembly under which they are indented.
-26-
1. * Parts included in Master Seal Kit Part No. 15705.
2. Basic Seal Kit Part No. 15707.
3. Set Crossover Relief Valve @ 3800 ± 400 P.S.I. @ 2-1/2 G.P.M.
E-60 with (1-1/4” Lift Ram Assembly)
Set Pump Relief Valve @ 2500 ± 50 P.S.I. full flow @ 1.85 G.P.M.
E-60 & E-60H with (1-3/4” Lift Ram Assembly)
Set Pump Relief Valve @ 2000 ± 50 P.S.I. full flow @ 1.85 G.P.M.
QUIK-LIFT® E-60 and E-60H
Exploded View
NOTE: E-60 - ITEM #2
1-1/4" RAM ASSEMBLY 15706 IS STILL AVAILABLE.
ITEM
A
B
C
D
PART NO.
15690
15691
15692
15694
NOTE: E-60 - ITEM #2
RAM ASSEMBLY HAS CHANGED and IS NOW 1-3/4"
LIFT RAM ASSEMBLY IS PART NO.15335
DESCRIPTION
PISTON
PACKING CUP
WASHER
CYLINDER
15
14
TO UPDATE 1-1/4" LIFT RAM ASSEMBLY TO 1-3/4"
ORDER UPDATE KIT NUMBER 08839.
22
24
E-60H
10
3
87
12
86
83
A
B
88
C
9
90
91
17
D
39
49
31
30
26
35
37
57
67
66
65
64
63
51
32
27
59
52
41
60
28
68
"H"
UNITS ONLY
23
38
77
78
79
50
24
8
9
20
80
44
45
43
58
82
60
5
16
40
76
6
21
89
81
92
7
4
29
1-1/4" ASSEMBLY
2
85
2
18
7
48
3
13
19
GROOVES
DOWN
E-60 & E-60H
84
E-60
11
34
36
33
15972
15661
46
62
25
47
75
74
73
72
71
70
69
54
1
42
61
55
28
27
26
Figure 1A
-27-
28
53
54A
53A
55A
GENERAL INFORMATION
ADDITONAL REASSEMBLY POINTS
Using the proper guidelines and precautions, the
Quik-Lift® unit is easy to disassemble and reassemble.
See Page 27-28 for an exploded view which applies to
the E-60 and E-60H models. It should be used as the
primary reference for proper reassembly. Where
necessary, this section includes additional information,
photographs and illustrations to assure proper and
efficient repairs.
O-Rings-
Coat liberally with hydraulic fluid and
position carefully to minimize possibility
of damage during assembly.
Fasteners- Torque all fasteners which are specified to
insure proper reliability and prevent
damage due to over-tightening.
UNIT DISASSEMBLY AND REASSEMBLY
PUMP
Model E-60, E-60H units with the exception of the
Power Angling Valve Assembly, the parts and
disassembly / reassembly procedures are common to
all models.
Shaft Seal Replacement
1.
Remove motor as shown in Figures 3-3 through
3-6 (pages 29-30).
Many repair procedures, including removal and
replacement of all Solenoid Valves, can be
accomplished without removing the unit from the
vehicle. While Figures 3-2 through 3-85 show the unit
clamped in a vise, make all possible repairs on the
vehicle when possible.
2.
Remove motor mounting plate as shown in Figures
3-7 and 3-8 (page 30).
3.
Using a 1/2” deep well socket punch out the
original shaft seal, being careful not to damage
the motor mounting plate.
NOTE: Pump Assembly should not be disassembled
since it cannot be serviced.
4.
Liberally coat the replacement seal I.D. with
hydraulic fluid.
Motor should be taken to the appropriate Fenner/Iskra
authorized service station in your area for all parts and
service with the exception of brush replacement.
Procedure for Fenner/Iskra motor brush replacement
is covered separately in this section.
5.
Carefully place the replacement seal spring side
up into the motor mounting plate until it is squarely
against the casting.
6.
Square a block of wood over the seal and use it
and a plastic or leather mallet to squarely drive
the seal into the motor mounting plate.
7.
Replace the motor as shown in Figures 3-80
through 3-82 (page 49).
Disassembly
See Figures 3-2 through 3-41 (pages 29-38) for
important disassembly points on both models.
See Figures 3-49 through 3-56 (Pages 41-42) for
Crossover Relief disassembly.
Reassembly
See Figures 3-42 through 3-48 (pages 39-40), and
Figures 3-70 through 3-84 (pages 46-50) for important
reassembly points both models.
See Figures 3-57 through 3-69 (Pages 43-46) for
Crossover Relief reassembly.
See Figures 3-85 (Pages 50) for Crossover Relief
Settings.
See Figures 3-83 (Pages 49) for Drain Plug assembly.
-28-
DISASSEMBLY -ALL MODELS
FIGURE 3-2
FIGURE 3-3
To drain oil from the unit, remove the drain plug using a
1/4” Allen wrench also remove pressure relief valve.
To remove motor, first remove the two phillip head
screws from the motor end cover. For brush
replacement see Figures 3-87 and 3-88 (page 52).
FIGURE 3-4
FIGURE 3-5
To replace the motor remove the two cap screws, use a
3/8” hex socket on the Fenner motor.
To replace the motor remove the two cap screws, use a
10mm hex socket on the Iskra motor. For brush
replacement see Figures 3-86 (page 52).
-29-
DISASSEMBLY - ALL MODELS
FIGURE 3-6
FIGURE 3-7
Hold the motor parts together while removing it from the
pump.
Remove the two 5/16 x 3-1/4” Cap screws and Nylite
washers using a 1/4” Allen wrench.
FIGURE 3-8
FIGURE 3-9
Remove Motor Mounting Plate from Sump Base using a
large screwdriver and mallet, tapping lightly around the
cover.
Using a 9/16” hex socket, remove the two 3/8 x 3-1/4”
bolts and Starwashers that hold the pump in place.
-30-
DISASSEMBLY - ALL MODELS
FIGURE 3-10
FIGURE 3-11
Remove Pump Mounting Plate.
Remove Pump Mounting Plate Locator Pin.
FIGURE 3-12
FIGURE 3-13
Remove Pump Check Valve.
There are two filters located within the E-60 and E-60H
units. Remove Lower Filter Cap Nut using a 11/16” hex
socket.
-31-
DISASSEMBLY - ALL MODELS
FIGURE 3-14
FIGURE 3-15
Remove Lower Filter and clean before reassembly.
Remove the Lower Adjusting Screw Cap Nut using a
11/16” hex socket.
FIGURE 3-16
FIGURE 3-17
Directly beneath the Cap Nut is the location of the Lower
Adjustment Screw. Remove the Lower Adjustment Screw
from the Sump Base using a 3/16” Allen wrench.
Remove Pressure Port Filter Cap Nut.
-32-
DISASSEMBLY - ALL MODELS
FIGURE 3-18
FIGURE 3-19
Remove Pressure Port Filter and clean before
reassembly.
Use a 1/2” Hex Socket remove retaining nut and then
remove “A” Coil from “A” Cartridge.
FIGURE 3-20
Remove “A” Cartridge using a 7/8” hex head deep
well socket.
FIGURE 3-21
Remove “A” Cartridge from Sump Base.
-33-
DISASSEMBLY - ALL MODELS
FIGURE 3-22
FIGURE 3-23
Remove Pressure Relief Cap Nut using a 1” hex socket.
Remove Pressure Relief Adjusting Screw, Pressure
Spring, Ball and Ball Seat from Sump Base. To Remove
Ball Seat from Sump Base use a 3/16” Allen wrench.
FIGURE 3-24
FIGURE 3-25
Remove “B” Cartridge using a 1-1/4”” hex head deep
well socket.
Use a 7/16” Hex Socket remove retaining nuts and
then remove “B” and “C” Coils from their Cartridges.
-34-
DISASSEMBLY - ALL MODELS
FIGURE 3-27
FIGURE 3-26
A magnetic probe is useful for removal of small parts.
Remove the 7/16” Ball located directly beneath the “B”
Cartridge
Remove “B” Cartridge from Sump Base.
FIGURE 3-28
FIGURE 3-29
Remove “C” Cartridge using a 1-1/4”” hex head deep
well socket.
Remove “B” Check Valve Spring from Valve Body.
-35-
DISASSEMBLY - ALL MODELS
FIGURE 3-31
FIGURE 3-30
Use a 13/16” hex socket to remove Pilot Valve Plug.
Remove “C” Cartridge from Sump Base.
FIGURE 3-32
FIGURE 3-33
Pilot Check Piston being removed. Handle Piston with
care. If Piston is scratched or damaged, it must be
replaced.
The Valve Body can be removed from Sump Base using
a 1/4” Allen wrench.
-36-
DISASSEMBLY - ALL MODELS
FIGURE 3-34
FIGURE 3-35
Use a 1/4” Allen wrench to remove Pilot Valve Plug.
Pilot Check Spring being removed from Valve Body.
FIGURE 3-36
Pilot Check Ball being removed. This is a 3/8”
diameter steel ball.
Before removing Ram and Piston Assembly, extend rod
fully. This drains out remaining oil in Cylinder.
FIGURE 3-37
-37-
DISASSEMBLY - ALL MODELS
FIGURE 3-38
FIGURE 3-39
To remove the Top Cap Assembly, use a 1/2” hex socket
to remove locknuts. The Studs usually unscrew from the
Sump Base with the locknuts.
Top Cap cover is removed from Reservoir using a large
screwdriver and mallet as shown, tapping lightly around
the Top Cap.
FIGURE 3-40
FIGURE 3-41
Remove Ram and Cylinder Assembly from Reservoir,
then pull Ram out of Cylinder. Worn Packing Cup on
Piston should be replaced.
Remove Cylinder Tank from Sump Base.
-38-
REASSEMBLY ALL MODELS
FIGURE 3-43
FIGURE 3-42
Remove Locknuts and Nylite washers from Studs. Screw
Studs (coarse thread) into Sump Base
Remove Lift Cylinder O-ring located in bottom of Sump
Base. Note E-60 uses a 1-1/2” diameter O-ring and the
E-60H, uses a 1-15/16” O-ring.
FIGURE 3-44
FIGURE 3-45
Clean all paint from Ram. Then slide Cylinder over the
Ram Piston Assembly using a rubber or leather mallet.
Install O-ring in bottom of Sump Base. Install Lift Cylinder
Assembly making sure it seats squarely on the O-ring.
-39-
REASSEMBLY - ALL MODELS
FIGURE 3-47
FIGURE 3-46
Reinstall Reservoir using a mallet to seat Reservoir
squarely.
Install Washer, with the notches facing downward, and
install Top Cap Seal.
FIGURE 3-48
Install Top Cap Assembly using mallet to seat Top Cap,
making certain that the Pressure Relief Valve Assembly
is properly located.
-40-
CROSSOVER RELIEF VALVE DISASSEMBLY - ALL MODELS
FIGURE 3-49
FIGURE 3-50
Remove Acorn Nut and O-ring using a 15/16” open end
wrench.
Remove Plug and Adjusting Screw using a 3/8” open
end wrench.
FIGURE 3-51
FIGURE 3-52
Remove Plug, Adjusting Screw and Disc.
Remove Pressure Spring.
-41-
CROSSOVER RELIEF VALVE DISASSEMBLY - ALL MODELS
FIGURE 3-53
FIGURE 3-54
Remove Poppet, Guide, Washer and Spacer.
Remove Cage and O-ring using Special Tool.
FIGURE 3-56
FIGURE 3-55
Correct order when reassembling Crossover Relief Valve.
Note: All parts should be dipped in oil prior to their
assembly.
Remove Bottom O-ring using Special Tool.
-42-
CROSSOVER RELIEF VALVE REASSEMBLY - ALL MODELS
FIGURE 3-57
FIGURE 3-58
Reinstall O-ring making certain it is seated to the bottom
of the cavity.
Install small O-ring into top of Cage.
FIGURE 3-59
FIGURE 3-60
Install small Bushing onto Poppet.
Assemble Poppet with Bushing into Cage as shown.
-43-
CROSSOVER RELIEF VALVE REASSEMBLY - ALL MODELS
FIGURE 3-61
FIGURE 3-62
To install Bushing, assemble Washer onto the Poppet
as shown. Press Washer down on Cage, this will put
equal pressure on the Bushing. Hold Washer in place
then remove Poppet from Cage.
Slide O-ring over bottom of Cage. Do Not push O-ring
completely over shoulder of cage. Drop Cage Assembly
into block cavity.
FIGURE 3-63
Seat Cage Assembly to the bottom of the Block
Cavity using a drift pin of approximately the same
diameter. Tap drift pin lightly until Cage Assembly
bottoms out and seals against O-rings.
FIGURE 3-64
Reassemble Poppet into Cage.
-44-
CROSSOVER RELIEF VALVE REASSEMBLY - ALL MODELS
FIGURE 3-65
Reassemble Washer smooth side up.
FIGURE 3-66
Assemble Spacer.
FIGURE 3-67
Reassemble Spring Guide smooth side down.
FIGURE 3-68
Reassemble Spring.
-45-
CROSSOVER RELIEF VALVE REASSEMBLY - ALL MODELS
FIGURE 3-69
Reassemble Plug with Adjusting Screw and Disc.
To properly adjust the Crossover Relief Valve refer to
page 21. Push leading edge of the Moldboard against
an immovable object until Crossover Relief Valve opens.
(3800 P.S.I. + 400). Reassemble Acorn Nut (61) and
O-ring (60).
REASSEMBLY - ALL MODELS
FIGURE 3-70
Install three new O-rings in Sump Base.
FIGURE 3-71
Install P.A. Block Assembly using 5/16-18 x 1-1/2”
soc. head screws. Torque to 96-120 in. lbs.
-46-
REASSEMBLY - ALL MODELS
FIGURE 3-72
Install Pressure Relief Valve in the order shown.
Note: Torque Seat to 125 in. lbs.
FIGURE 3-73
Install Lower Adjustment Screw, new Filters and
Torque Plugs to 75-85 in. lbs. with a 11/16” hex
socket.
FIGURE 3-74
Install Locator Pin and Pump Check Valve in the
following order as shown.
FIGURE 3-75
Install Pump Mounting Plate making certain that the
small hole in plate is directly over the Pump Check
Valve.
-47-
REASSEMBLY - ALL MODELS
FIGURE 3-76
Hold Pump Check Valve in place with Special Tool.
Install Pump Mounting Plate.
FIGURE 3-77
Install Pump making certain that the dowel pins on
the bottom of Pump are aligned with holes located
in the Pump Mounting Plate. Torque Pump mounting
bolts evenly to ensure proper shaft alignment with
the Pump Shaft Seal. Torque bolts to 185 + 5 in.
lbs.
FIGURE 3-78
Install Motor Mounting Cover using new Nylite
washers and 5/16-18 x 3-1/4” cap screws. Note:
motor replacement (Two Terminal) requires new
Mounting Plate Part No. 15831. See Fig.3-79
FIGURE 3-79
Torque Cap Screws to 100-125 in. lbs.
-48-
REASSEMBLY - ALL MODELS
FIGURE 3-80
Install two terminal motor with power terminals facing
up as shown. Torque bolts to 60-72 in. lbs.
FIGURE 3-81
Install single terminal motor with power terminal
facing to the rear as shown. Torque bolts to 60-72
in. lbs.
FIGURE 3-82
Install Fenner Motor Cover making certain that the
drain holes in the cover are facing downward.
FIGURE 3-83
Install Drain Plug.
-49-
REASSEMBLY - ALL MODELS
FIGURE 3-84
Refill unit with Meyer M-1 Fluid 1” to 1-1/2” from Top
Cap with Ram all the way down.
FIGURE 3-85
To adjust operating pressure of the hydraulic unit,
turn the adjusting screw clockwise to raise the
pressure and counter clockwise to lower the pressure.
E-60 (1-1/4” Ram) Set pressure to 2500 ± 50 P.S.I.
E-60 & E-60H
Set pressure to 2000 ± 50 P.S.I.
VALVE CARTRIDGE INFORMATION
VALVE CARTRIDGES “B” and “C”
IMPORTANT: The valve cartridges can be damaged
beyond repair by bending or denting the tube, the
portion of the cartridge surrounded by the coil.
Therefore, do not grip the cartridge tube with pliers or
clamp it in a vise.
Use only 1-1/4" hex deep socket to remove Cartridges.
NOTE: Cartridges without a hex nut must use special
tool No. 21891 to remove and reinstall the “B” and “C”
Cartridges. See Figure 3-89 (page 54).
“A” CARTRIDGE
When jamming of the spool occurs, attempt to
eliminate it using the method described under “A”
Cartridge before disassembling it.
NOTE: Use only a 7/8" or a 1-1/8" hex deep socket to
remove and reinstall the “A” Cartridge.
The “A” Cartridge cannot be disassembled. When
operating normally, the poppet can be pushed in
approximately .030".
The “B” and “C” Cartridges can be disassembled by
removing the internal retaining ring. When operating
normally, the spool can be pushed in approximately
.070". However, it is generally a better use of one’s
time to replace the cartridge. In the event jamming or
some other malfunction cannot be eliminated, replace
the cartridge since individual parts for it are not
available.
Jamming of the poppet due to metal chips or other
contamination can usually be eliminated by immersing
the entire cartridge in clean kerosene and pushing the
poppet in and out with a probe until it moves freely.
Dry with compressed air and reinstall.
In the event jamming cannot be eliminated, replace
the cartridge.
-50-
BRUSH REPLACEMENT OF ISKRA MOTOR
FIGURE 3-86
Remove motor from hydraulic unit. Remove top cap from motor housing. To replace brushes (part # 15854) start by
pushing each brush assembly towards the commutator. Remove old assembly from the insulated mounting plate,
removing retaining screws. Replace with a new brush assembly by reversing the above procedure. It is recommended
that each brush be changed in turn to avoid confusion, make sure that each brush assembly is replaced with the correct
part that has the brush cable on the the same side. Service Kits consist of 2 matching pairs of brush assemblies.
BRUSH REPLACEMENT OF FENNER MOTOR
FIGURE 3-87
To remove brushes, first remove screws from brush
leads using a phillip head screwdriver.
FIGURE 3-88
To remove brushes from motor housing, insert a flat
head screwdriver underneath the tension springs. Pry
upward and remove brush. Reinstall new brushes in
reverse order.
-51-
SPECIAL TOOLS
Crossover Relief Valve
Inner Harden Steel Wire from a Throttle/Choke cable
7.00"
0.13"
FIGURE 3-89
“B” and “C” Cartridge Tool, #21891.
FIGURE 3-90
6.00"
0.06"
0.63"
0.75"
FIGURE 3-91
Pump Check Valve Tool
-52-
SECTION 4 -
SPECIFICATIONS
SOLENOID SWITCH
Applied Voltage
12 Volts DC
Max. Current Draw
5 Amperes
Nominal resistance (ohm meter lead connected to coil
lead, other meter lead connected to metal foot)
2.65 to 4.5 ohms.
ELECTRICAL SPECIFICATIONS
MOTOR
FENNER
No load (motor not attached to pump)
NOTE: Do not operate motor continuously for
more than 30 seconds.
Applied Voltage
Max. Current Draw
12 Volts DC
150 Amperes
Speed (Min.)
3,200 RPM
HYDRAULIC SPECIFICATIONS
PUMP - Pressure Output
E-60 (1-1/4” Lift Ram)
E-60 & E-60H (1-3/4” Lift Ram)
CROSSOVER RELIEF VALVE
Opening Pressure
Under load (pump operating in relief)
NOTE: Do not operate motor continuously for
more than 5 seconds.
Applied Voltage
Max. Current Draw
12 Volts DC
230 Amperes
Model E-60
Unit
Hoses & 1-1/2 x 10 Cylinders
Total
Model E-60
Unit
Hoses & 1-1/2 x 12 Cylinders
Total
3,200 RPM
Model E-60H
Unit
Hoses & 2 x 12 Cylinders
Total
Under load (pump operating in relief)
NOTE: Do not operate motor continuously for
more than 5 seconds.
Applied Voltage
Max. Current Draw
3800 P.S.I. + 400
HYDRAULIC FLUID CAPACITY
NOTE :1 Quart = 32 Fluid Ounces
ISKRA AMJ4739 12V.
No load (motor not attached to pump)
NOTE: Do not operate motor continuously for
more than 30 seconds.
Applied Voltage
12 Volts DC
Max. Current Draw
150 Amperes
Speed (Min.)
2500 ± 50 P.S.I.
2000 ± 50 P.S.I.
Model E-60H (MDII)
Unit
Hoses & 1-1/2 x 10 Cylinders
Total
12 Volts DC
230 Amperes
SOLENOID VALVES :
44 oz.
16 oz.
1 qt., 28 oz.
(60 oz.)
44 oz.
19 oz.
1 qt., 31 oz.
(63 oz.)
48 oz.
28 oz.
2 qt., 12 oz.
(76 oz.)
48 oz.
16 oz.
2 qt.
(64 oz.)
“A”, Coil
Applied Voltage
Current Draw
12 Volts DC
1.2 Amperes
TORQUE SPECIFICATIONS
Thread
Torque
Size
(In. Lbs.)
Nominal resistance (ohm meter lead connected
to coil lead, other meter lead connected to metal
coil cover) 9.6 ohms ± 10% Plastic cover Coil
10.0 ohms ± 10%
Reservoir Cover
Retaining Nuts
Pump Assembly
Retaining Cap Screws
End Plate or Valve Block
Retaining Cap Screws
Motor to Pump Retaining
Cap Screws
Motor Mounting Plate
Drain and Filter Plugs
“A” Coil Retainer Nut
”B” and “C” Coils
Applied Voltage
Current Draw
12 Volts DC
1.24 Amperes
Nominal resistance (ohm meter lead connected
to coil lead, other meter lead connected to metal
coil cover) 3.73 ohms + 3%.
-53-
5/16-24
100-125
5/16-24
185 + 5
5/16-18
96-120
1/4-20
5/16-18
9/16-18
45-55
100-125
75-85
40 + 2
QUIK-LIFT®
power unit
service manual
MODELS
E-60, E-60H
Meyer Products
18513 Euclid Ave. • Cleveland, OH 44112-1084
Phone (216) 486-1313
email•[email protected]
© 2005 Printed in the U.S.A.
Diamond Equipment
6 Angell Lane• Damariscotta, ME 04543-9720
Phone (207) 563-2227
www.diamondplow.com • email [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement