Salamander Designs IR-3002, 440-297, 440-296, 056-007, 900-040, 400-080, 300-518, 300-565, 300-115, 440-322 Users guide

IR ALL IN ONE includes these items:
1. Mounting IR Hub
Mounting to Salamander
Furniture with Aluminum Frame
SalamanderDesigns.com
1 - Hex Key
#400-080
2 - Button Head Screws
#300-518
Use two Drop-In Nuts with two
Button Head Screws to mount Hub
on the inside or backside of cabinet
attaching to aluminum post.
Slip nut into slot and tighten the
button head screw to lock the nut
into place.
2 - Drop-in Nuts
#300-565
Note: Nut must slant from top left
to bottom right as shown below.
2 - Wood Screws
#300-115
2 - IR Emitters
#IR-3002
IR Receiver
Mounting to Wood Cabinets
36’’
Use supplied wood screws to mount
Hub to interior or exterior of cabinet.
al l i n o n e
1 - Power Supply
#056-007 (USA)
#900-040 (EU,UK)
users guide
Doc #500-160 v12.08
2. Attach IR Receiver
Attach Receiver Holster to front
of cabinet and place the IR Receiver
in holster.
4 - IR Emitter Holsters
#440-297
1 - IR Receiver Holster
#440-296
3. Attach Emitters
LED Status Indicators:
Power and IR Data
DC Power Input
Attach IR Emitter Holsters in front
of IR sensors of each component
and place the IR Emitter in holster.
6 - Wire Managers
#440-322
4 IR Emitter outputs
Note: IR Receiver should be
placed within sight.
Emitter Holster
Receiver Holster
Features
• IR remote is compatible with any A/V component that has the All-In-One Solution
by Salamander Designs.
• The plasma proof remote head IR receiver uses advances optical and electronic
filtering for interference rejection.
• LED lights provide power and IR signal status.
Emitter
Receiver
Wire Manager
DC Adapter
• A 2-piece design makes it easy to conceal and simple to install.
Specifications
Note: Be sure the Emitter is
securely attached directly over the
component’s IR receptor. To locate
the IR receptor, shine a flashlight at
the unit and look for the sensor.
Specifications:
Power Supply:
IR Freq. Range Supported:
IR Pickup Range:
IR Receiver Head Dimensions:
IR Emitter Outputs:
(Typical)
USA:
In: 110V - 120V
EU, UK: In: 120V - 240V, 50 - 60Hz
Out: 8 - 12V
30 kHz - 60 kHz
40 ft. @ 38kHz, 25 ft. @ 56kHz
0.65’’ x 0.35’’ x 0.25’’
4* (expandable to 8)
*Compatible with Channel Vision™ IR-3002
Specifications subject to change without notice.
Limited Warranty
Salamander Designs will repair or replace any defect in material or workmanship
which occurs during normal use of this product with new or rebuilt parts, free of
charge in the USA, for two years from the date of original purchase. This is a no
hassle warranty with no mail in warranty card needed. This warranty does not cover
damages in shipment, failures caused by other products not supplied by
Salamander Designs, or failures due to accident, misuse, abuse, or alteration of the
equipment. This warranty is extended only to the original purchaser, and a
purchase receipt, invoice, or other proof of original purchase date will be required
before warranty repairs are provided.
Mail in service can be obtained during the warranty period by calling toll-free (800)
535-5659. A Return Authorization number must be obtained in advance and can be
marked on the outside of the shipping carton.
This warranty gives you specific legal rights and you may have other rights (which
vary from state to state). If a problem with this product develops during or after the
warranty period, please contact Salamander Designs, your dealer or any
factory-authorized service center.