DIMENSIONS (mm) CHARACTERISTICS 150 85

DIMENSIONS (mm) CHARACTERISTICS 150 85
UG-3 Smoke detector housing for duct installation
UG-3 Smoke detector housing for duct installation
Instruction Manual
Instruction Manual
DIMENSIONS (mm)
CHARACTERISTICS
150
85
●
Patented venturi pipe and duct housing
●
One-pipe air sampling system Uniguard Superflow
●
New cross-section (shape) of the venturi pipe gives
an optimum of venturi effect
180
146
Test hole on cover
●
Simple installation
●
Sensitive flow indicator
●
Simple service and maintenance
●
Installer-friendly connection of cables
●
Foolproof installation of venturi pipe
154
TECHNICAL DATA
27
●
35
FUNCTION
Adaptor housing:
ABS
Uniguard Superflow has been developed to detect
Protection:
IP-54
smoke in ventilation ducts and consists of an
Weight:
800g
adaptor system where both venturi pipe and
Air sampling pipe:
Aluminium.
housing are specially designed for optimum
airflow through the smoke detector.
Standard length 0,6 m. Hole diameter 38 mm.
The length of the venturi pipe shall be chosen
Uniguard Superflow has 4 premounted IP67
based upon how wide the ventilation duct is. The
approved cable entries with built-in cable
venturi pipes are available in 3 lengths; 0,6, 1,5
anchorage for diameter 4-11 mm, type Klikseal.
and 2,8 m. When the ventilation duct is wider than The detector has a bayonet fitting to simplify
0,6 m (dia), the venturi pipe should penetrate the
mounting and removal.
whole duct.
4 © 2010 Nittan UK
© 2010 Nittan UK
1
UG-3 Smoke detector housing for duct installation
UG-3 Smoke detector housing for duct installation
Instruction Manual
Instruction Manual
Drill a hole
Ø 38 mm.
Drill a hole
Ø 38 mm.
Diameter of the duct bigger
than 0,6 m.
The venturi pipe should
penetrate the whole duct.
Max diameter of the duct 0,6 m.
Use the venturi pipe 0,6 m.
Shorten the pipe, if necessary.
Shorten the pipe to correct length.
For ducts with a ø of less than 0,6 m use the 0,6 m pipe.
For ducts with a ø of between 0,6 m and 1,4 m use the 1,5 m pipe.
For ducts which are larger than 1,4 m use the 2,8 m pipe.
INSTALLATION
WIRING DIAGRAM
The venturi pipe is made of aluminium and can
The numbering by the terminal blocks on the
easily be shortened to suit the diameter of the
printed circuit board in the Uniguard Superflow
duct. Hole diameter is 38 mm. For insulated or
corresponds to the connectors on the embedded
circular ducts - use the mounting bracket, hole
smoke detector base.
diameter is then 51 mm.
AIR FLOW MONITORING
Insert the end plug.
The detector is fitted with a red plastic switch
Put on the end plastic
gasket.
tongue. When the detector is correctly installed,
Put on the rubber
gasket, TET 26-35.
the tongue is bent outwards by the air flow. The
switch tongue provides a simple confirmation that
there is no leakage and that the air flow from the
NOTE!
Drill a hole
Ø 51 mm.
duct is in fact flowing through the housing.
Terminal block in
Uniguard Superlow
Connectors in
smoke detector base
6
1
2
3
4
5
6
5
1
Base
(Nittan)
2
4
3
FUNCTION TEST
The venturi pipe shall not
protrude more than 30 mm
through the duct wall.
When installation is complete, the detector should
be tested. This can be carried out with smoke or
suitable testspray, using the test hole on cover. Do
BASIC PRINCIPLES FOR
POSITIONING
ACCESSORIES
Item code
Designation
For the airflow through the adaptor to be
UG-MB
Mounting bracket (for insulated/
NB: When installing outdoors or in cold attics etc.,
circular ducts)
where there is a risk for condensation, the
representative of the airflow in the ventilation
duct, install the detector at a place where flow
meters etc. should normally be mounted.
not forget to refit the plastic plug after test.
detector should be insulated from the
UG-COVER
ORDER EXAMPLE
Waterproof housing (for
surrounding air with e.g. weatherproof housing
mounting outdoors, in cold
UG-COVER.
attics etc.)
Item code
Designation
UG-3/NIT
Uniguard Superflow
VENTURI EFFECT
VR-0.6M
Venturi pipe (length 0,6 m)
VR-1.5M
Venturi pipe (length 1,5 m)
VR-2.8M
Venturi pipe (length 2,8 m)
flow and makes the venturi pipe self-adjusting
C/W TET 26-35 Gasket
with a stable and uniform flow from the whole
housing
The new cross-section (shape) of the venturi pipe
gives an optimum of venturi effect. The slots
alongside the venturi pipe, for the inlet and the
outlet of the venturi air stream, gives maximum air
cross section of the ventilation duct.
2 © 2010 Nittan UK
© 2010 Nittan UK
3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement