Avenview SW-HDM3D-C5-8X8 Specifications

Avenview SW-HDM3D-C5-8X8 Specifications
8x8 HDMI Matrix Switch with 3D
over CAT-5 with IR Pass-Through
Model #: SW-HDM3D-C5-8X8
© 2009 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or warranties with
respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any
time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in
Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products
www.avenview.com
1
including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
Reproduction of this manual, or parts thereof, in any form, without the express written permission of Avenview Inc. is strictly prohibited.
Table of Contents
Section 1: Getting Started ...................................................................................................................... 3
1.1
Important Safeguards ............................................................................................................ 3
1.2
Safety Instructions ................................................................................................................. 3
1.3
Regulatory Notices Federal Communications Commission (FCC) ......................................... 4
1.4
Introduction ........................................................................................................................... 4
1.5
Package Contents................................................................................................................... 6
1.6
Before Installation.................................................................................................................. 6
1.7
Panel Description ................................................................................................................... 7
1.7.1 SW-HDM3D-C5-8X8 Front Panel ........................................................................................... 7
1.7.2 SW-HDM3D-C5-8X8 Rear Panel ............................................................................................ 7
1.7.3 HDM3D-C5SW-R .................................................................................................................... 8
1.7.4 Dip Switch for EDID & Audio Settings (SW1 – SW8).............................................................. 9
1.7.5 SW Main Dip Switch for Firmware Update ......................................................................... 10
1.8
IR Control Patch ................................................................................................................... 11
1.9
Installation (SW-HDM3D-C5-8X8) ........................................................................................ 12
1.10
Operation and IR Control ..................................................................................................... 13
1.10.1 Source Side ........................................................................................................................ 13
1.10.2 Display Side ....................................................................................................................... 14
1.11
RS232 Serial Port Control ..................................................................................................... 15
1.11.1RS232 Commands .............................................................................................................. 17
Section 2: Specifications....................................................................................................................... 18
www.avenview.com
2
Section 1: Getting Started
1.1
Important Safeguards
Please read all of these instructions carefully before you use the device. Save this manual for future
reference.
What the warranty does not cover


Any product, on which the serial number has been defaced, modified or removed.
Damage, deterioration or malfunction resulting from:
 Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized
product modification, or failure to follow instructions supplied with the product.
 Repair or attempted repair by anyone not authorized by us.
 Any damage of the product due to shipment.
 Removal or installation of the product.
 Causes external to the product, such as electric power fluctuation or failure.
 Use of supplies or parts not meeting our specifications.
 Normal wear and tear.
 Any other causes which does not relate to a product defect.

Removal, installation, and set-up service charges.
1.2
Safety Instructions
The Avenview SW-HDM3D-C5-8X8 HDMI Matrix Switch with 3D over CAT-5 with IR Pass-Through has been
tested for conformance to safety regulations and requirements, and has been certified for international use.
However, like all electronic equipments, the SW-HDM3D-C5-8X8 should be used with care. Read the following
safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.




Do not dismantle the housing or modify the module.
Dismantling the housing or modifying the module may result in electrical shock or burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing housing may expose you to
dangerous voltage or other hazards


Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid
falls or spills on to the housing, unplug the module immediately.
Have the module checked by a qualified service engineer before using it again.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before
cleaning.


www.avenview.com
3
1.3
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this
equipment.
1.4
Introduction
The Avenview SW-HDM3D-C5-8X8, HDMI Matrix Switch with 3D over CAT-5 with IR Pass-Through provides the
most flexible and cost effective solution in the market to route high definition video sources plus
multi-channel (up to 7.1 channel) digital audio from any of the four HDMI sources to the remote displays at
the same time. Through low cost Cat-5/5e/6 LAN cables, not only high quality video and audio can be
transmitted to the display sites, but also users can switch among four HDMI sources using the push-in button
or remote control. With single power design at the source site, each remote module is easily installed without
power supply. Furthermore, the built-in IR extension function makes users at display site access the DVD
player, PS3 or any HDMI supported devices directly.
www.avenview.com
4
www.avenview.com
5
-
1.5
Silicon Image chipset embedded for best quality, compatibility and reliability
Support HDMI Deep Color & full 3D
HDCP compliant
Allows any source to be displayed on multiple displays at the same time
Allows any HDMI display to view any HDMI source at any time
Supports 7.1 channel digital audio
Supports default HDMI EDID and learns the EDID of displays
The matrix master can switch every output channels to any HDMI inputs by push-in button, IR remote
control, or RS-232 control
Allows controlling local HDMI sources such as DVD and TiVo by attached IR extender from remote
receiver to matrix master
Allows to control matrix master through IR remote control at remote receiver’s site
Extends video signal up to 35m (115 feet) over CAT5e at 1080p and likely longer with better HDMI
source device, better grade HDMI display, and better quality solid CAT6 cable
Easy installation with rack-mounting and wall-mounting designs for master and receiver respectively
Fast response time – 2~5 seconds for channel
Package Contents
Before you start the installation of the converter, please check the package contents.
-
SW-HDM3D-C5-8X8
HDM3D-C5SW-R
IR Transmitter
IR Receiver
IR Remote Control
Rackmounting Ear
Power Adapter (+5VDC, 4A)
x1
x8
x8
x1
x1
x2
x1
-
User’s Manual
x1
1.6




Before Installation
Put the product in an even and stable location. If the product falls down or drops, it may cause an
injury or malfunction.
Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high
humidity.
Use the DC power adapter with correct specifications. If inappropriate power supply is used then it
may cause a fire.
Do not twist or pull by force ends of the optical cable. It can cause malfunction.
www.avenview.com
6
1.7
Panel Description
1.7.1 SW-HDM3D-C5-8X8 Front Panel
1.
Power: Power Control
2.
Seven Segment LED Indicators: LED display for
output ports and input channels
3.
Front Panel Push Buttons: Front panel push
buttons used to select the number of input
source and display channel
4.
IR SENSOR: IR sensor for receiving the IR
commands from the IR remote
1.7.2 SW-HDM3D-C5-8X8 Rear Panel
1.
RS232: RS-232 control port
2.
SW 1-8: DIP Switch
3.
HDMI 1 – 8: HDMI Inputs
4.
IR OUTPUT 1 – 8: 3.5mm IR blaster socket for
individual HDMI source control
5.
CAT-5 OUTPUT: RJ-45 outputs for each output
channel
6.
AC Power: 100-250V
7.
MAIN IR: 3.5mm IR blaster socket for HDMI
source control on all 8 inputs s
8.
MAIN SW: DIP switches
9.
USB: HDMI local output
www.avenview.com
7
1.7.3 HDM3D-C5SW-R
1.
IR INPUT: Plug in IR receiver.
2.
+5V DC: Spare power jack for over 60m
transmission when the RX may need external
power to work.
3.
HDMI SIGNAL: Plug in the CAT5 connected to the
respective A/V SIGNAL port on the
SW-HDM3D-C5-8X8
4.
IR SIGNAL: Plug in the CAT5 connected to the
respective CHANNEL CONTROL port on the
SW-HDM3D-C5-8X8
5.
INPUT : Display the current showing HDMI source
channel
6.
INPUT SELECT: Push button for switching input
source channel in sequential order
7.
EQ Level: Adjust the 8-level equalization control
to the received HDMI signals. The HDMI signal
level varies from 0 (strongest) to 7 (weakest) for
respective transmission length from longest
possible range to short distance. Please adjust the
signal level from 7 to 0 and stop turning the
rotary switch whenever the audio/video is playing
normally. Inappropriate signal level setting may
cause overpowering issue that would shorten the
product life significantly!
8.
HDMI OUT: Connect to HDTV with a HDMI cable
www.avenview.com
8
1.7.4 Dip Switch for EDID & Audio Settings (SW1 – SW8)
DIP Switch Position
PIN # 1
PIN # 2
Video
Audio
OFF 
OFF 
1080p
Surround
OFF 
ON 
Up to 1080p
Stereo
ON 
OFF 
Up to
720p/1080i
Stereo
ON 
ON 
Bypass
4
2
4
Bypass
Description
1
Default Mode 1 : EDID up to 1080p video & surround
sound audio output up to 7.1ch (DTS-HD Master &
Dolby TrueHD)
Default Mode 2: EDID up to 1080p video and stereo
audio for basic compatibility among HDTVs
3
Safe Mode : EDID up to 720p/1080i video and stereo
audio for basic compatibility among HDTVs
5
EDID Learning Mode : for learning EDID from the
display while playing any received HDMI audio format
1
Factory default setting of [SW1]-[SW8] is pin-1 at OFF [] & pin-2 at OFF [] for 1080p video and surround sound
audio.
2
If the HDTV shows video but without audio, please try to set audio mode to stereo.
3
If you encounter any unsolved audio/video output problem during system installation, please turn any [SW1]-[SW8]
to pin-1 at ON [] & pin-2 at OFF [] for safe mode to select the system EDID up to 720p(1080i) video and stereo
audio for system check. However, the safe mode cannot be initiated if your HDMI source is set to enforce 1080p
output. In this case, please reconfigure your HDMI source to all resolution output for troubleshooting.
4
Bypass means the matrix will maintain playing the original format of HDMI signals in video and perhaps audio. By
setting at this mode, the users may encounter compatibility issue among different kinds of HDMI sources and
displays. If you cannot get the audio and/or video output normally at the system installation, please change the
DIP switch setting to default mode or even safe mode to verify the functionality of the device.
5
To learn the EDID of HDMI display for respective HDMI source devices, please see the [EDID Learning] section in the
next page for more information
www.avenview.com
9
1.7.5 SW Main Dip Switch for Firmware Update
DIP Switch Position
Normal Operation Mode
[via RS-232 port]6
Firmware
Update Mode7
Block A [main]
Block B [remote]
Block C [HDMI]
PIN # 1
PIN # 2
PIN # 3
PIN # 4
OFF 
OFF 
OFF 
OFF 
ON 
OFF 
OFF 
OFF 
ON 
OFF 
ON 
OFF 
ON 
ON 
OFF 
OFF 
6
Factory default for SW Main is pin#1-OFF [], pin#2-OFF [], pin#3-OFF [], & pin#4-OFF []. PLEASE MAINTAIN
THIS SETTING AT ANYTIME FOR REGULAR USE VIA RS-232 CONTROL!
7
Sequence for firmware update
WARNING!
[Firmware update only can be done via RS-232 port and connection to PC set at COM1)
[1]. Power off the Matrix unit. Execute the firmware update program on your PC via COM1 port connection to the
RS-232 port of the Matrix unit.
[2]. Set the pin#1 of [SW Main] at ON [] for firmware update mode.
[3]. Set pin#2 and pin#3 at respective positions to assign which Block to be updated.
[4]. Power on the Matrix unit. The firmware update program should begin this update sequence automatically. If
not, please check the RS-232 connection status between PC and Matrix unit.
[5]. After the OK message shows up to indicate the firmware update sequence for designated Block is complete,
please turn off the Matrix unit.
[6]. Repeat step 3 ~ step6 if you want to update the firmware of the remaining Blocks.
[7]. Set the [SW Main] switch position to Normal Operation Mode.
[8]. Power on the Matrix unit.
www.avenview.com
10
1.8
IR Control Patch
IR Transmitter Cable
IR Receiver Cable
IR Main
The default location for IR emitter extension cable to transmit all IR command signals received
from any of the four remote receivers to all of the HDMI sources.
IR1
IR emitter extension cable connected here can only transmit IR command signals from the
remote receivers that are setting at the input channel 1.
IR2
IR emitter extension cable connected here can only transmit IR command signals from the
remote receivers that are setting at the input channel 2.
IR3
IR emitter extension cable connected here can only transmit IR command signals from the
remote receivers that are setting at the input channel 3.
IR4
IR emitter extension cable connected here can only transmit IR command signals from the
remote receivers that are setting at the input channel 4.
www.avenview.com
11
1.9
Installation (SW-HDM3D-C5-8X8)
To setup Avenview SW-HDM3D-C5-8X8 follow these steps for connecting to a device:
1.
2.
3.
4.
5.
6.
7.
Connect all sources to HDMI Inputs on the 8X8 HDMI over CAT5 Matrix Switch (SW-HDM3D-C5-8X8)
Connect each DDC output on the SW-HDM3D-C5-8X8 to respective DDC input on the remote receiver
HDM3D-C5SW-R
Connect each TMDS output on the SW-HDM3D-C5-8X8 to respective TMDS input on the remote
receiver HDM3D-C5SW-R
Connect IR emitter cable to the SW-HDM3D-C5-8X8 and direct the IR emitter to the build-in IR
receiver of the sources
Connect the +5V 6A DC power supply to the SW-HDM3D-C5-8X8
Power on all HDMI sources
Power on the SW-HDM3D-C5-8X8
www.avenview.com
12
1.10 Operation and IR Control
1.10.1 Source Side
1.10.1.1Method A: Push Button
1.
Use the “” or “—“ channel button on output port to select which port to be changed.
“”: change selected output port in ascending order
“—“: change selected output port in descending order
2.
Push the “” or “—“ channel button on Input channel to select the HDMI input source you want to
display on this selected output port in step 1 in sequential order. Once you reach the desired input
channel you want to display on this selected output port, leave it and the setting will be effective in a
few seconds.
1.10.1.2Method B: IR Remote Control
Firstly please push one of the INPUT buttons to choose which HDMI input source you are going to setup.
After that, you can have multiple outputs playing the same content from the selected INPUT #1-#8 by
pushing the corresponding OUTPUT buttons. The setting will be effective in a couple of seconds.
INPUT 1
HDMI input port #1
INPUT 2
HDMI input port #2
INPUT 3
HDMI input port #3
INPUT 4
HDMI input port #4
INPUT 5
HDMI input port #5
INPUT 6
HDMI input port #6
INPUT 7
HDMI input port #7
INPUT 8
HDMI input port #8
OUTPUT 1
HDMI output port #1
OUTPUT 2
HDMI output port #2
OUTPUT 3
HDMI output port #3
OUTPUT 4
HDMI output port #4
OUTPUT 5
HDMI output port #5
OUTPUT 6
HDMI output port #6
OUTPUT 7
HDMI output port #7
OUTPUT 8
HDMI output port #8
www.avenview.com
13
1.10.2 Display Side
1.10.2.1Method A: Push Button
Press the INPUT SELECT push button to switch the input source on the respective output port connected to
the matrix receiver in sequential order. The selected input source will be displayed on the LED of INPUT
CHANNEL.
1.10.2.2Method B: IR Remote Control for Switching Input Channels
Please decide which input channel to be selected by pressing Source Selection 1 to Source Selection 8. Or
you can use left
and right
button to enter IR control mode and select the input channel in
ascending and descending order respectively. The setting will be effective in a couple of seconds.
Switch input port in descending order*
Switch input port in ascending order*
SOURCE SEL. 1
SOURCE SEL. 2
SOURCE SEL. 3
SOURCE SEL. 4
SOURCE SEL. 5
SOURCE SEL. 6
SOURCE SEL. 7
SOURCE SEL. 8
Switch the display channel at the remote
site to input port 1
Switch the display channel at the remote
site to input port 2
Switch the display channel at the remote
site to input port 3
Switch the display channel at the remote
site to input port 4
Switch the display channel at the remote
site to input port 5
Switch the display channel at the remote
site to input port 6
Switch the display channel at the remote
site to input port 7
Switch the display channel at the remote
site to input port 8
Note
Right (
) button to switch input source in ascending order (1, 2, 3, 4, 5, 6, 7, 8, 1, 2, ......)
Left (
) button to switch input source in descending order (1, 8, 7, 6, 5, 4, 3, 2, 1, 2, ......)
1.10.2.3Method C: IR Remote Control for Controlling the HDMI Sources
Users can use the corresponding IR remote to control respective DVD player or any HDMI compliant devices
including SW-HDM3D-C5-8X8 itself with IR control at any display site.
www.avenview.com
14
1.11 RS232 Serial Port Control
Scan:
Press Scan button, the machine will scan the all com port and
show them.
Select the RS232 serial port connected to the machine. And set
device ID 255 is for all device.
Only the same device id or 255 can get the command you sent.
Press OK. Get the new status from the machine you select.
Setting:
Press Get button to read back device ID.
Press Set button to write device ID.
www.avenview.com
15
Linkage: Press Linkage button to read back all status
Open / Close : Press this button to Close or Open COM Port.
Mapping Button:
Select All Output:
Select “set all output”, then select the source on main menu.
You can quickly set all output to the same source.
Unselect All Output:
Release output selection.
Select Input1~8-Output:
Select Input Source. Then select the output port icon.
For example:
Select input source 1. Then select output port one and two. The
video and audio will be send to port one and two.
Fast Select Button:
Press Fast select button. Quick setting.
Input one  Output Port one
Input two Output Port two
…..
Press Fast select pull down menu.
Select Input Num-Output Num
Input source #1  Output port #1
Input source #2  Output port #2
…..
Select Input* - All Output
Send the same source to all output.
Output Port:
Pull down menu and select which source to be sent to this output port.
One by one setting
On main menu screen.
First select input source. Then select the output ports which you want to
send the video and audio from this source. When you select the input
source, the source will change to gray. When you select the output port
one by one, the selected output port will change to gray.
The linking line will change to yellow.
www.avenview.com
16
Group setting
First select output ports one by one. Then select the input source. The selected output ports change
the setting at the same time.
By using Terminal:
Baud rate:
Data length:
Parity check:
Stop bit:
9600
8bit
No
1
1.11.1RS232 Commands
COMMAND
ACTION
COMMAND
ACTION
COMMAND
ACTION
ST
System Status*
C5
Output C select Input5
F3
Output F select Input3
VR
Firmware Version
C6
Output C select Input6
F4
Output F select Input4
A1
Output A select Input1
C7
Output C select Input7
F5
Output F select Input5
A2
Output A select Input2
C8
Output C select Input8
F6
Output F select Input6
A3
Output A select Input3
D1
Output D select Input1
F7
Output F select Input7
A4
Output A select Input4
D2
Output D select Input2
F8
Output F select Input8
A5
Output A select Input5
D3
Output D select Input3
G1
Output G select Input1
A6
Output A select Input6
D4
Output D select Input4
G2
Output G select Input2
A7
Output A select Input7
D5
Output D select Input5
G3
Output G select Input3
A8
Output A select Input8
D6
Output D select Input6
G4
Output G select Input4
B1
Output B select Input1
D7
Output D select Input7
G5
Output G select Input5
B2
Output B select Input2
D8
Output D select Input8
G6
Output G select Input6
B3
Output B select Input3
E1
Output E select Input1
G7
Output G select Input7
B4
Output B select Input4
E2
Output E select Input2
G8
Output G select Input8
B5
Output B select Input5
E3
Output E select Input3
H1
Output H select Input1
B6
Output B select Input6
E4
Output E select Input4
H2
Output H select Input2
B7
Output B select Input7
E5
Output E select Input5
H3
Output H select Input3
B8
Output B select Input8
E6
Output E select Input6
H4
Output H select Input4
C1
Output C select Input1
E7
Output E select Input7
H5
Output H select Input5
C2
Output C select Input2
E8
Output E select Input8
H6
Output H select Input6
C3
Output C select Input3
F1
Output F select Input1
H7
Output H select Input7
C4
Output C select Input4
F2
Output F select Input2
H8
Output H select Input8
www.avenview.com
17
Section 2: Specifications
Item
Units
Unit Description
Description
SW-HDM3D-C5-8X8
HDM3D-C5SW-R
8x8 HDMI Matrix Switch with 3D over
CAT-5 with IR Pass-Through
HDMI Matrix Switch with 3D Receiver
HDMI Compliance
Support HDMI Deep Color & full 3D
HDCP Compliance
Yes
Video Bandwidth
Single Link 225 MHz (6.75Gbps)
Supported Resolutions
480i / 480p / 720p / 1080i / 1080p60
Full HD: (1080p) ~ 35meter (115feet) (CAT5e) / 40meter (130feet) (CAT6)
HD: (720p/1080i) ~ 50meter (165feet) (CAT5e) / 55meter (180feet) (CAT6)
Resolution and Distance
Audio Support
Surround Sound (up to 7.1 Ch) or Stereo Digital Audio
Equalization
N/A
8 Level Digital Control
Input TMDS Signal
1.2 Volts (peak-to-peak)
Input DDC Signal
ESD Protection
Input
Output
HDMI Input Selection
HDMI Source Control
5 Volts (peak-to-peak, TTL)
-
Human body model — ±19kV (air-gap discharge) & ±12kV (contact discharge)
Core chipset — ±8kV
1 x RJ45 TMDS
8 x HDMI
1 x RJ45 DDC
1 x RS232
1 x IR Socket for IR Receiver
8 x RJ45 HDMI Signal
8 x RJ45 IR Control
1 x HDMI
9 x IR Socket for IR Transmitter
Push Button / IR Remote / RS232
Push Button / IR Remote
Through IR Control Path from IR Receiver
HDMI Connector
Type A (19 pin female)
RJ45 Connector
WE/SS 8P8C with 2 LED indicators
RS232 Connector
DIP Switch
Dimensions (L x W x H)
Power Supply
Power Consumption
DE-9 (9-pin D-sub Female)
Yes
-
17” x 11.4” x 1.7”
3.3” x 3.5” x 1”
AC Power 100-250V
Most not required
60 Watt (max)
1.5 Watt (max)
provided by SW-HDM3D-C5-8X8
Environmental
Operating Temperature
32˚ ~ 104˚F (0˚ to 40˚C)
Storage Tempearture
-4˚ ~ 140˚F (-20˚ ~ 60˚C)
Relative Humidity
20~90% RH (no condensation)
www.avenview.com
18
Notice
1.
If the DVI or HDMI device requires the EDID information, please use EDID Reader/Writer to
retrieve and provide DVI/HDMI EDID information.
2.
All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz
LAN cable and ASTRODESIGN Video Signal Generator VG-859C.3
3.
The transmission length is largely affected by the type of LAN cables, the type of HDMI sources,
and the type of HDMI display. The testing result shows solid LAN cables (usually in bulk cable
300m or 1000ft form) can transmit a lot longer signals than stranded LAN cables (usually in
patch cord form). Shielded STP cables are better suit than unshielded UTP cables. A solid UTP
CAT5e cable shows longer transmission length than stranded STP CAT6 cable. For long extension
users, solid LAN cables are your only choice.
4.
EIA/TIA-568-B termination (T568B) for LAN cables is recommended for better performance.
5.
To reduce the interference among the unshielded twisted pairs of wires in LAN cable, you can use
shielded LAN cables to improve EMI problems, which is worsen in long transmission.
6.
Because the quality of the LAN cables has the major effects in how long transmission distance
will be made and how good is the received display, the actual transmission length is subject to
your LAN cables. For resolution greater than 1080i or 1280x1024, a CAT6 cable is recommended.
7.
If your HDMI display has multiple HDMI inputs, it is found that the first HDMI input [HDMI input
#1] generally can produce better transmission performance among all HDMI inputs.
www.avenview.com
19
Disclaimer
While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the
operation or use of Avenview hardware, software or other products and documentation described herein, for any act or omission of
Avenview concerning such products or this documentation, for any interruption of service, loss or interruption of business, loss of
anticipatory profits, or for punitive, incidental or consequential damages in connection with the furnishing, performance, or use of the
Avenview hardware, software, or other products and documentation provided herein.
Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability,
function or design. With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties
regarding such products, including but not limited to, the implied warranties of merchantability, fitness for a particular purpose, and
non-infringement.
www.avenview.com
20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement