Better, Safer Drinking Water PLATINUM Reverse Osmosis Ultra Filtration Under Sink Filtration Designer Faucets & Accessories 44 Aqua Flo Platinum QCRO & QCUF Drinking Water Systems Customized Drinking Water Water conditions can vary even in the same community. The Aqua Flo Platinum QCRO System can be configured to meet your specific requirements. There are ten interchangeable filters with a variety of treatment options that can be tailored to local water conditions, so your water is the best it can be. PLATINUM If you’re concerned about RO reject water or RO drain line makes installation difficult, we offer UltraFiltration (UF).* The UF does not have a drain line to run, your cost is lesser than RO and there is no waste. The innovative QC twist and lock design makes service simple. Twist off the old cartridge and twist on the new. No messy sump removal. Aqua Flo Platinum HP systems make drinking water better and life easier. * Check with water treatment specialist to recommend you an RO or UF system depending on your untreated water quality. “The innovative QC twist and lock design makes service simple. ” Drinking Water 45 Aqua Flo Platinum QCRO & QCUF Drinking Water Systems Product Specifications Sediment Filters. Screens out sediments and particles. Various micron size filters are available. Manifold Assembly. The single manifold ensures reliability. Houses four separate filter technologies in a unique space saving design. Carbon Filters. Reduces elements that cause water to taste and smell unpleasant, including chlorine taste and odor. Automatic Shutoff Valve. Shuts off the system when reservoir tank is full. Reservoir Tank. Durable, high quality, powder coated, steel tank ensures you’ll have a plentiful supply of refreshing water. Various size tanks are available. Reverse Osmosis Filters. Reduces dissolved substances. Various capacity membranes are available. Designer Faucet. Multiple styles and colors are available. (Standard faucet shown) Specialty Filters. Optimize drinking water taste and adjust to local water supply with a wide array of custom filter options. Filter Cartridge and Single Stage Standalone System Specifications Sediment Filter Carbon Block Filter Carbon Block Filter GAC Carbon Filter pH Booster Filter Cartridge UF (Hollow Fiber) Membrane Carbon Block - 1 Mic Filter Scale Reduction Purpose Sediment Removal Chlorine Taste and Odor Chlorine Taste and Odor Polishing - Taste and Odor Raise pH of water and removal of chlorine, taste and odor Ultra Fine Filtration Chlorine Taste and Odor, Particulate Reduction Scale Inhibitor Type Polypropylene Carbon Block Carbon Block Granular Activated pH Booster and Remineralizer Carbon Filter Hollow Fiber Mechanical Filtration Carbon Block Scale Reduction Micron 5 5 50 – – 0.1 1 To be changed every 12 months 750 Gallons 1500 gallons Capacity* 2000 gallons 2000 gallons 2000 gallons 2000 gallons To be changed every 6 months Minimum Flow Rate @ 60psi 0.5 gal/min 0.5 gal/min 0.5 gal/min 0.5 gal/min 0.5 gal/min 0.5 gal/min 0.5 gal/min 0.5 gal/min CBQC1/4 CB50QC1/4 GACQC1/4 PHQC1/4 UFQC1/4 CB1QC1/4 SCALEQC1/4 Single Stage SEDQC1/4 System Model #** * May vary depending on water quality **Single Stage Standalone System Port Connection Size - 1/4” Quick Connect Standard System Specifications* Model QCRO4V-50 Number of Stages Stage 1 (Pre-Filter) Stage 2 (Pre-Filter) Stage 3 (Membrane) Stage 4 (Post-Filter) Output (GPD)† 4 4 4 Sediment Filter Sediment Filter Sediment Filter Activated Carbon Filter Activated Carbon Filter Sediment Filter Thin Film Composite Membrane Thin Film Composite Membrane Thin Film Composite Membrane Activated Carbon Filter Activated Carbon Filter Activated Carbon Filter 50 75 720 Booster Pump Models 15 – 60 psi Temperature pH Range 40-100°F 3.0-11.0 Note: Pretreatment suggested if conditions exceed parameters. Must be installed on potable water. 46 Drinking Water QCUF 15.8” 14.5” 4.7” QCRO4V-50 system certified by WQA to NSF/ ANSI 58 and CSA B483.1 for the reduction of the following substances, as verified and substantiated by test data: Arsenic V, Barium, Cadmium, Chromium III and VI, Copper, Fluoride, Lead, Radium 226/228, Selenium, TDS and Turbidity 13.1” Feed Water Guidelines Maximum TDS 2000 ppm Hardness <7gpg Iron (Fe) <0.2ppm Manganese (Mn) <0.05ppm Hydrogen Sulfide 0.0ppm Turbidity <1.0NTU Feed Water Pressure 40-100psi QCRO4V-75 2.5” Aqua Flo Platinum 1240 Series Aqua Flo Platinum 1240’s advanced reverse osmosis drinking water systems are a natural and economical solution for providing your family with high quality drinking water. With a space-saving ultra slim profile, the system tucks neatly under your kitchen sink providing bottled water quality right from your very own tap. All systems are backed by a two year limited warranty. The Smartap® water quality monitor found on the Push Button designated models is backed by a five year limited warranty. All models feature: 0 At a touch of the button, the Push Button Monitor option alerts you when it is time to change your filters. 0 High quality reverse osmosis membrane 0 Choice of 25, 50 and 75 gallons per day membranes 0 Sediment pre-filtration 0 Pre & Post Carbon block filtration 0 3/8” tubing from RO to tank and faucet for higher flow 0 Chrome faucet 0 Simple snap fit cover for ease of service 0 New slim profile with integrated mounting bracket for easy, space saving installation 0 Quick connect fittings Patented SmartTap® model provides a push button monitor alerting you when it is time to replace your RO membrane 0 Color coded tubing for ease of installation 0 Metal 3.0 gal Storage Tank “A natural and economical solution for providing your family with high quality ” drinking water. Drinking Water 47 Aqua Flo Platinum 1240 Series Booster Pump (R/O feed water line booster pump) Raises the water pressure and maintains it at the ideal level for the system to operate at maximum efficiency. Recommended for use on supplies with low pressure or high concentrations of total dissolved solids (TDS). The pump is self-priming and whisper-quiet. It runs on a 24VAC transformer (included) from a standard 120VAC electrical outlet. 4VTFC-PB Push Button System includes: Flexible mounting plate, quick connect fittings and a pressure shut-off switch. 4VTFC Item #: 70030001 Model: RO Booster with Pressure Switch and Transformer for 25 to 75 Gallon per day Systems NOTE: All units 3VTFC ship with Metal storage tank. Model Description Vessels Sediment Filter Pre-Filter Membrane Post-Filter Rating GPD Monitor Dimensions H x W x D (in) 3VTFC25G 3VTFC50G 4VTFC25G 4VTFC50G 4VTFC75G 4VTFC25G-PB 4VTFC50G-PB 4VTFC75G-PB 3 3 4 4 4 4 4 4 None None String Wound Polypropylene String Wound Polypropylene String Wound Polypropylene String Wound Polypropylene String Wound Polypropylene String Wound Polypropylene Dual-Purpose Dual-Purpose Activated Carbon Activated Carbon Activated Carbon Activated Carbon Activated Carbon Activated Carbon TFC TFC TFC TFC TFC TFC TFC TFC Activated Carbon Activated Carbon Activated Carbon Activated Carbon Activated Carbon Activated Carbon Activated Carbon Activated Carbon 25 50 25 50 75 25 50 75 None None None None None Push Button Push Button Push Button 11 x 15 x 3.75 11 x 15 x 3.75 14 x 15 x 3.75 14 x 15 x 3.75 14 x 15 x 3.75 14 x 15 x 3.75 14 x 15 x 3.75 14 x 15 x 3.75 Feed Water Guidelines Maximum TDS 2000 ppm Hardness <7gpg Iron (Fe) <0.2ppm Manganese (Mn) <0.05ppm Hydrogen Sulfide 0.0ppm Turbidity <1.0NTU Feed Water Pressure 40-100psi Booster Pump Models 15 – 60 psi Temperature pH Range 40-100°F 3.0-11.0 Note: Pretreatment suggested if conditions exceed parameters. Must be installed on potable water. 48 Drinking Water Aqua Flo Reverse Osmosis System Features: 0 Four stage filtration: 5 micron sediment pre-filter, 10 micron coconut carbon pre & post filters, quick connect 75 GPD NSF Certified TFC membrane 0 Bayonet-style 1/4 turn quick connect disposable cartridges with auto water shut-off 0 Includes non air-gap faucet and 3.0 gallon NSF Certified storage tank. (Air Gap & Designer Faucets Available) 0 3/8” tubing for high product flow rate from tank to faucet Fast, Simple & Sanitary Maintenance! Quick connect disposable cartridges and membrane make for easy ‘Do-It-Yourself’ maintenance. With built in auto water shut-offs there is no need to turn off the water supply prior to maintenance. Because traditional systems require the disinfection of the permanent housing canisters and involve more direct human contact, maintenance can take as much as an hour and if not done properly can result in a contaminated system. Disposable cartridges change in seconds and reduce contamination risk! 0 Quick connect fittings, inlet saddle and drain saddle, labelled tubing for easy installation 0 Booster pump model with inlet solenoid raises water pressure to ideal level for maximum efficiency. Recommended on rural supplies with low pressure or high TDS 0 Optional 10 micron carbon block and granular activated carbon filters available. 0 Two year warranty (excluding consumable filter cartridges and RO membrane) 0 Dimensions: 13”w x 141/2”h x 41/2 d No Pump 141/4”w x 161/2”h x 61/4”d Pump Model Model Description Stages Sediment Filter Pre-Filter Membrane Post-Filter Rating GPD Dimensions H x W x D (in) Aqua Flo 475 PRO Aqua Flo 475 PRO BP 4 4 5 Micron 5 Micron 10 Micron Coconut Carbon 10 Micron Coconut Carbon TFC TFC 10 Micron Coconut Carbon 10 Micron Coconut Carbon 75 75 14.5 x 13 x 4.5 16.5 x 14.5 x 6.25 Feed Water Guidelines Maximum TDS 2000 ppm Hardness <7gpg Iron (Fe) <0.2ppm Manganese (Mn) <0.05ppm Hydrogen Sulfide 0.0ppm Turbidity <1.0NTU Feed Water Pressure 40-100psi Booster Pump Models 15 – 60 psi Temperature pH Range 40-100°F 3.0-11.0 Change filters in seconds without turning off water! No tools required! Note: Pretreatment suggested if conditions exceed parameters. Must be installed on potable water. Drinking Water 49 Aqua Flo Under Sink Filtration Systems 475QC Filters The 475 Quick Change Filter Series offers 3, 2 & Single Stage options to provide solutions for a variety of water problems including sediment, rust, bad taste & odor. Features & Benefits: 0 Low cost alternative to RO 0 No reject water (100% water used) 0 Leaves nutrients in water 0 Ultra Filtration on system removes lead, VOC (pesticides, herbicides, chemicals), THM, chlorine, taste and odor and sediment down to 0.2 microns. 0 Installation is quick and easy 0 Quick change bayonet-style disposable cartridges are more sterile and can be changed in seconds 0 Includes standard chrome faucet, inlet saddle valve, and 5ft ¼” tubing 0 No storage tank required Change filters in seconds without turning off water! No tools required! 0 Dimensions: • 3 stage - 11.8”w x 14.3”h x 4.5”d • 2 stage - 6.3”w x 13.4”h x 3.9”d • 1 stage - 2.8”w x 12.4”h x 3.2”d 475 QC Series Filter Systems Description 475QC-3 TRIPLE STAGE ULTRA FILTER Filter 1 SED Filter 2 UF 475QC-2 DOUBLE STAGE DUAL FILTER SED COC 475QC-1C SINGLE STAGE COCONUT CARBON FILTER COC 475QC-1S SINGLE STAGE SEDIMENT FILTER SED 475QC-1G SINGLE STAGE GAC FILTER GAC 475 QC Series Filters Description SEDIMENT FILTER SED-10 BLUE (475 Q SERIES) CARBON FILTER COC-10 PURPLE (475 Q SERIES) CARBON FILTER GAC-10 YELLOW (475 Q SERIES) ULTRA FILTER UF-10 BLACK (475 Q SERIES) 50 Drinking Water Filter 3 COC MICRON FLOW RATE CAPACITY (GALLONS) 5 10 0.2 1 GPM 1 GPM 0.7 GPM 0.7 GPM 900 1,500 1,500 1,500 Aqua Flo Economy Reverse Osmosis System 0 Pre-filters 10’’ five (5) micron Spun Polypropylene Sediment Cartridge and 10’’ Activated Carbon Cartridge 0 Post filter: 10’’ Activated Carbon Cartridge 0 Choose from air gap or non-air gap chrome plated faucets 0 3.0 Gallon NSF Certified plastic storage tank 0 3/8’’ outlet tubing for higher flows 0 Automatic shut-off valve 0 Exclusive serviceable check valve eliminates spring ‘chatter’ noise common in other RO’s Features: 0 Heavy duty glass filled polypropylene construction provides double the strength, toughness & durability compared to most other RO’s which are typically constructed with ABS. 0 TFC 75 GPD reverse osmosis membrane provides up to 99% Total Dissolved Solids (TDS) rejection Model Description Stages Aqua Flo Economy 75 Aqua Flo Economy 75 BP 4 4 Sediment Filter 0 Quick connect fittings for ease of installation 0 Powder coated bracket 0 Dual purpose wrench for use on membrane cap and filter housing 0 Dimensions: 0 15.0”w x 14.5”h x 6.1”d No Pump 15.0”w x 17.7”h x 6.9”d Pump Model Pre-Filter & Post Filter 5 Micron Spun Poly 10 Micron Granular Activated Carbon 5 Micron Spun Poly 10 Micron Granular Activated Carbon Membrane Rating GPD TFC TFC 75 75 Dimensions H x W x D (in) 14.5 x 15 x 6.1 17.7 x 15 x 6.9 Booster Pump Model also includes: 0 Pump mounted on RO to maintain constant water pressure 0 Raises water pressure to ideal level for maximum efficiency 0 Use on rural supplies with low pressure or highTDS 0 Exclusive Auto Flush feature extends membrane life 0 Self-priming and whisper quiet 0 24VAC transformer (included) from a standard 120VAC electrical outlet 0 Flexible mounting plate, quick connect fittings and pressure shut-off switch Feed Water Guidelines Maximum TDS 2000 ppm Hardness <7gpg Iron (Fe) <0.2ppm Manganese (Mn) <0.05ppm Hydrogen Sulfide 0.0ppm Turbidity <1.0NTU Feed Water Pressure 40-100psi Booster Pump Models 15 – 60 psi Temperature pH Range 40-100°F 3.0-11.0 JG Undersink 3/8” connection angle stop / shut off JG Undersink 1/4” connection angle stop / shut off Note: Pretreatment suggested if conditions exceed parameters. Must be installed on potable water. Drinking Water 51 Designer RO Faucets Designer RO faucets are a stylish addition to any kitchen. The NSF Certified lead-free ceramic disk faucets are available in many attractive finishes to coordinate with any decor. The faucets feature lead-free plastic water passages and lead-free brass gooseneck spouts that swivel 360 degrees for ease of use. Specifications Height Spout Reach Mounting Hole Diameter Base Diameter VS888 VS905 11.5” (292mm) 11.075” (281.32mm) 5.7” (146mm) 4.75” (120mm) 1/2” (12.5mm) 1/2” (12.5mm) 1.73” (44mm) 1.76” (44.8mm) Connection 1/4” compression nut fitting 1/4” compression nut fitting Operating Pressure 125 PSI/8.3BAR 125 PSI/8.3BAR Flow Rate 1.0 gpm/3.785lpm @35 PSI/2.32BAR 1.0 gpm/3.785lpm @35 PSI/2.32BAR Temp Rating Warranty 4°C/40°F to 70°C/158°F 4°C/40°F to 70°C/158°F 2 Years 2 Years * All mounting hardware included. A 3/8” quick connect faucet adapter fitting (#PP3212U7W) can be purchased seperately. VS888 VS905 Color Sample Display #87591 52 Drinking Water RO Booster Pumps PAB8800 Series High Flow Booster Pump Key Operational Benefits: 0 Boosts pressure 40 to 120 psi (adjustable) 0 Used with membranes 50 to 120 GDP 0 15,000+ operating hours (estimated) 0 Quiet – less than 52 DBA 0 Can run dry without damage Features: 0 Toughest, most durable pump on the market 0 More flow at extremely low inlet pressures 0 Adjustable max. outlet psi (regardless of feed pressure) 0 New motor venting system to remove moisture 0 Expels trapped air (no more air locks) 0 Can be mounted with pump head up or horizontal 0 EMI/RFI electronic noise suppression 0 100% final performance tested 0 Available in 12VDC and 24VDC Aquatec 5800 Demand Pump OPERATION: The 5800 pump can draw water from a holding tank and pressurize it, or boost the pressure from a low pressure source. They are designed to operate intermittently, but most versions can run continuously for several hour intervals. The pumps can be operated in demand mode controlled by an integral pressure switch, or in delivery mode controlled by an external power switching device. An integral bypass may be used to limit pressure. POWER: 115V PSI: 60 GPM: 0.9 MOUNTING: A steel mounting base with four hollow rubber grommets is standard and included at no extra cost. The pump may be mounted in any position. FITTINGS: The 5800 pump is offered with integral John Guest style quick connect fitting for 3/8” OD semi rigid tubing. KemFlo MD1050 Booster Pump DESCRIPTION: 110/230 VAC, 75 GPD Booster pump 1.0 L.min, suitable for applications with 24VDC transformer SPECIFICATIONS: Kemflo MD Series booster pump with 3/8” FNPT, made from NSF grade material high power flow rate and quality. Meet ROHS standard. Drinking Water 53 Reverse Osmosis Storage Tanks Flexwave is a line of RO accumulators and storage tanks for residential and light commercial applications. Flexwave tanks are made in the USA and built to comply wiith NSF/ANSI Std 61. All Flexwave tanks have a 5 year warranty. # 70031000 Quick Connect Ball Valve Assembly reduces 1’’ tank connection to John Guest Quick Connect RO ball valve 1/4’’ to 3/8’’ tubing. Larger sizes available. Please contact Customer Service for details. Tank precharge 20 PSI Maximum Pressure 125 PSI Maximum working temperature, internal & external 120F Materials of Construction Tank top and bottom domes injection molded copolymer polypropylene. Shell extruded Polypropylene. Outer shell composite construction with fiberglass coated with epoxy resin. Base is injection molded high-impact ABS. 100% butyl diaphragm connected to a copolymer polypropylene bottom water chamber which allows for complete evacuation of the water chamber. Dimensions & Capacities Model FWRO15 FWRO22 Item # Total Tank Volume 92372 92374 Gallons 15 Gal 22 Gal Litres 56.8 83.3 Height In 25.6 34.1 Cm 65 87 Diameter In 16.5 16.5 Cm 42 42 Quick Sizing Chart Model FWRO15 FWRO22 54 Item # Total Tank Volume 92372 92374 Gallons 15 Gal 22 Gal Drinking Water Litres 56.8 83.3 Total Drawdown 10/50 10/60 Gallons Litres Gallons Litres 9.3 35.2 10 37.9 13.6 51.5 14.7 55.6 Connection In 1” NPT 1” NPT Total Weight Lbs 19 25 Kilos 8.6 11.3
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021