Sony DVP-NS38 User Guide Manual Operating Instruction Pdf

Sony DVP-NS38 User Guide Manual Operating Instruction Pdf
3-283-146-11(2)
CD/DVD
Player
Operating Instructions
DVP-NS38
DVP-NS39
© 2008 Sony
Corporation
Downloaded From DvDPlayer-Manual.com Sherwood
Manuals
In case of products that for safety,
performance or data integrity
reasons require a permanent
connection with an incorporated
battery, this battery should be
replaced by qualified service staff
only.
To ensure that the battery will be
treated properly, hand over the
product at end-of-life to the
applicable collection point for the
recycling of electrical and
electronic equipment.
WARNING
To reduce the risk of fire or
electric shock, do not expose
this apparatus to rain or
moisture.
To avoid electrical shock, do
not open the cabinet. Refer
servicing to qualified
personnel only.
The mains lead must only be
changed at a qualified
service shop.
Batteries or batteries
installed apparatus shall not
be exposed to excessive heat
such as sunshine, fire or the
like.
This appliance is classified as a
CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT
MARKING is located on the rear
exterior.
CAUTION
The use of optical instruments with
this product will increase eye
hazard. As the laser beam used in
this CD/DVD player is harmful to
eyes, do not attempt to disassemble
the cabinet.
Refer servicing to qualified
personnel only.
Notice for customers in the
United Kingdom and
Republic of Ireland
A moulded plug complying with
BS1363 is fitted to this equipment
for your safety and convenience.
Should the fuse in the plug
supplied need to be replaced, a
5AMP fuse approved by ASTA or
BSI to BS1362, (i.e., marked with
or
mark) must be used.
If the plug supplied with this
equipment has a detachable fuse
cover, be sure to attach the fuse
cover after you change the fuse.
Never use the plug without the fuse
cover. If you should lose the fuse
cover, please contact your nearest
Sony service station.
Disposal of Old Electrical &
Electronic Equipment (Applicable
in the European Union and other
European countries with separate
collection systems)
This symbol on the product or on
its packaging indicates that this
product shall not be treated as
household waste. Instead it shall be
handed over to the applicable
collection point for the recycling of
electrical and electronic
equipment. By ensuring this
product is disposed of correctly,
you will help prevent potential
negative consequences for the
environment and human health,
which could otherwise be caused
by inappropriate waste handling of
this product. The recycling of
materials will help to conserve
natural resources. For more
detailed information about
recycling of this product, please
contact your local Civic Office,
your household waste disposal
service or the shop where you
purchased the product.
Disposal of waste batteries
(applicable in the European Union
and other European countries with
separate collection systems)
This symbol on the battery or on
the packaging indicates that the
battery provided with this product
shall not be treated as household
waste. By ensuring these batteries
are disposed of correctly, you will
help prevent potentially negative
consequences for the environment
and human health which could
otherwise be caused by
inappropriate waste handling of the
battery. The recycling of the
materials will help to conserve
natural resources.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
2
For all other batteries, please view
the section on how to remove the
battery from the product safely.
Hand the battery over to the
applicable collection point for the
recycling of waste batteries.
For more detailed information
about recycling of this product or
battery, please contact your local
Civic Office, your household
waste disposal service or the shop
where you purchased the product.
The manufacturer of this product is
Sony Corporation, 1-7-1 Konan
Minato-ku Tokyo, 108-0075
Japan. The Authorized
Representative for EMC and
product safety is Sony
Deutschland GmbH, Hedelfinger
Strasse 61, 70327 Stuttgart,
Germany. For any service or
guarantee matters please refer to
the addresses given in separate
service or guarantee documents.
Precautions
Safety
• This unit operates on 220 – 240
V AC, 50/60 Hz. Check that the
unit’s operating voltage is
identical with your local power
supply.
• To prevent fire or shock hazard,
do not place objects filled with
liquids, such as vases, on the
apparatus.
Installing
• Do not install the unit in an
inclined position. It is designed
to be operated in a horizontal
position only.
• Keep the unit and discs away
from equipment with strong
magnets, such as microwave
ovens, or large loudspeakers.
• Do not place heavy objects on
the unit.
On adjusting volume
Notes About the
Discs
• To keep the disc clean, handle
the disc by its edge. Do not touch
the surface. Dust, fingerprints, or
scratches on the disc may cause
it to malfunction.
Precautions
On safety
Should any solid object or liquid
fall into the cabinet, unplug the
player and have it checked by
qualified personnel before
operating it any further.
On power sources
• The player is not disconnected
from the AC power source
(mains) as long as it is connected
to the wall outlet, even if the
player itself has been turned off.
• If you are not going to use the
player for a long time, be sure to
disconnect the player from the
wall outlet. To disconnect the
AC power cord (mains lead),
grasp the plug itself; never pull
the cord.
• Do not expose the disc to direct
sunlight or heat sources such as
hot air ducts, or leave it in a car
parked in direct sunlight as the
temperature may rise
considerably inside the car.
• After playing, store the disc in its
case.
• Clean the disc with a cleaning
cloth. Wipe the disc from the
centre out.
• Do not use solvents such as
benzine, thinner, commercially
available cleaners, or anti-static
spray intended for vinyl LPs.
• If you have printed the disc’s
label, dry the label before
playing.
Do not turn up the volume while
listening to a section with very low
level inputs or no audio signals. If
you do, the speakers may be
damaged when a peak level section
is played.
On cleaning
Clean the cabinet, panel, and
controls with a soft cloth slightly
moistened with a mild detergent
solution. Do not use any type of
abrasive pad, scouring powder or
solvent such as alcohol or benzine.
On cleaning discs, disc/lens
cleaners
Do not use cleaning discs or
disc/lens cleaners (including
wet or spray types). These
may cause the apparatus to
malfunction.
On placement
On replacement of parts
• Place the player in a location
with adequate ventilation to
prevent heat build-up in the
player.
• Do not place the player on a soft
surface such as a rug.
• Do not place the player in a
location near heat sources, or in a
place subject to direct sunlight,
excessive dust, or mechanical
shock.
• Do not install this player in a
confined space, such as a
bookshelf or similar unit.
• Install the player so that the AC
power cord (mains lead) can be
unplugged from the wall socket
immediately in the event of
trouble.
In the event that this unit is
repaired, repaired parts may be
collected for reuse or recycling
purposes.
On operation
If you have any questions or
problems concerning your player,
please consult your nearest Sony
dealer.
• If the player is brought directly
from a cold to a warm location,
or is placed in a very damp room,
moisture may condense on the
lenses inside the player. Should
this occur, the player may not
operate properly. In this case,
remove the disc and leave the
player turned on for about half an
hour until the moisture
evaporates.
• When you move the player, take
out any discs. If you don’t, the
disc may be damaged.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
IMPORTANT NOTICE
Caution: This player is capable of
holding a still video image or onscreen display image on your
television screen indefinitely. If
you leave the still video image or
on-screen display image
displayed on your TV for an
extended period of time you risk
permanent damage to your
television screen. Plasma display
panel televisions and projection
televisions are susceptible to this.
3
Table of Contents
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Notes About the Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
This Player Can Play the Following Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Guide to Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Guide to the Control Menu Display (Magic Pad) . . . . . . . . . . . . . . . . . . . . . . 11
Hookups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Hooking Up the Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 1: Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 2: Connecting to your TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 3: Connecting to an Audio Component . . . . . . . . . . . . . . . . . . . . . . . . .
Step 4: Connecting the Mains Lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 5: Preparing the Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controlling Your TV With the Supplied Remote . . . . . . . . . . . . . . . . . . .
Step 6: Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
13
14
15
16
16
17
18
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Playing Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Various Play Mode Functions (Programme Play, Shuffle Play, Repeat Play,
A-B Repeat Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Playback Picture (CUSTOM PICTURE MODE) . . . . . . . . . . .
Sharpening the Picture (SHARPNESS) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Locking Discs (CUSTOM PARENTAL CONTROL,
PARENTAL CONTROL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
26
29
31
31
Searching for a Scene . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Searching for a Particular Point on a Disc (Scan, Slow-motion Play,
Freeze Frame) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Searching for a Title/Chapter/Track/Scene, etc. . . . . . . . . . . . . . . . . . . . . . . 35
Searching by Scene (PICTURE NAVIGATION) . . . . . . . . . . . . . . . . . . . . . . 37
Sound Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Changing the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
TV Virtual Surround Settings (TVS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Enjoying MP3 Audio and JPEG Images . . . . . . . . . . . . . . . . . . . . . 41
About MP3 Audio Tracks and JPEG Image Files . . . . . . . . . . . . . . . . . . . . . 41
Playing MP3 Audio Tracks or JPEG Image Files . . . . . . . . . . . . . . . . . . . . . 42
Enjoying JPEG Images as a Slide Show . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Enjoying DivX® Videos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
About DivX Video Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Playing DivX Video Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
4
Settings and Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Using the Setup Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Display or Sound Track Language (LANGUAGE SETUP) . . . . .
Settings for the Display (SCREEN SETUP) . . . . . . . . . . . . . . . . . . . . . . . . .
Custom Settings (CUSTOM SETUP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Settings for the Sound (AUDIO SETUP) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
49
50
51
52
53
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Self-diagnosis Function (When letters/numbers appear in the display) . . . .
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Language Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parental Control Area Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55
58
59
60
60
61
About This Manual
• Instructions in this manual describe the controls on the remote. You can also use the controls
on the player if they have the same or similar names as those on the remote.
• “DVD” may be used as a general term for commercial DVDs, DVD+RWs/DVD+Rs/DVD+Rs
DL (+VR mode) and DVD-RWs/DVD-Rs/DVD-Rs DL (VR mode, video mode).
• The meaning of the icons used in this manual is described below:
Icons
Meaning
Functions available for commercial DVDs and DVD+RWs/DVD+Rs/
DVD+Rs DL in +VR mode or DVD-RWs/DVD-Rs/DVD-Rs DL in video
mode
Functions available for DVD-RWs/DVD-Rs/DVD-Rs DL in VR (Video
Recording) mode
Functions available for VIDEO CDs (including Super VCDs or CD-Rs/
CD-RWs in video CD format or Super VCD format)
Functions available for music CDs or CD-Rs/CD-RWs in music CD format
Functions available for DATA CDs (CD-ROMs/CD-Rs/CD-RWs
containing MP3*1 audio tracks, JPEG image files, and DivX*2*3 video
files)
Functions available for DATA DVDs (DVD-ROMs/DVD+RWs/
DVD+Rs/DVD+Rs DL/DVD-RWs/DVD-Rs/DVD-Rs DL containing
MP3*1 audio tracks, JPEG image files, and DivX*2*3 video files)
*1 MP3 (MPEG-1 Audio Layer III) is a standard format defined by ISO (International Organization for
Standardization)/IEC (International Electrotechnical Commission) MPEG which compresses audio data.
*2 DivX® is a video file compression technology, developed by DivX, Inc.
*3 DivX, DivX Certified, and associated logos are trademarks of DivX, Inc. and are used under license.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
5
This Player Can Play the
Following Discs
Format of discs
Commercial DVD
DVD-RW/-R
DVD+RW/+R/
+R DL
VIDEO CD/
Music CD
CD-RW/-R
“DVD+RW,” “DVD-RW,” “DVD+R,”
“DVD+R DL,” “DVD-R,” “DVD VIDEO,”
and “CD” logos are trademarks.
Note about CDs/DVDs
The player can play CD-ROMs/CD-Rs/CDRWs recorded in the following formats:
– music CD format
– video CD format
– MP3 audio tracks, JPEG image files, and
DivX video files of format conforming to
ISO 9660* Level 1/Level 2, or its extended
format, Joliet
– KODAK Picture CD format
* A logical format of files and folders on CDROMs, defined by ISO (International
Organization for Standardization).
The player can play DVD-ROMs/
DVD+RWs/DVD+Rs/DVD+Rs DL/
DVD-RWs/DVD-Rs/DVD-Rs DL recorded
in the following formats:
– MP3 audio tracks, JPEG image files, and
DivX video files of format conforming to
UDF (Universal Disk Format).
Example of discs that the player
cannot play
The player cannot play the following discs:
• CD-ROMs/CD-Rs/CD-RWs other than
those recorded in the formats listed on this
page.
• CD-ROMs recorded in PHOTO CD format.
• Data part of CD-Extras.
• DVD Audio discs.
• HD layer on Super Audio CDs.
• DATA DVDs that do not contain MP3
audio tracks, JPEG image files, or DivX
video files.
• BDs.
• HD DVDs.
• Discs recorded with an AVCHDcompatible DVD video camera.
Also, the player cannot play the following
discs:
• A commercial DVD with a different region
code.
• A disc that has a non-standard shape (e.g.,
card, heart).
• A disc with paper or stickers on it.
• A disc that has the adhesive of cellophane
tape or a sticker still left on it.
Region code
Your player has a region code printed on the
back of the unit and only will play
commercial DVDs (playback only) labelled
with identical region codes. This system is
used to protect copyrights.
Commercial DVDs labelled
play on this player.
will also
If you try to play any other commercial DVD,
the message “Playback prohibited by area
limitations.” will appear on the TV screen.
Depending on the commercial DVD, there
may be no region code indication, even
though playing the commercial DVD is
prohibited by area restrictions.
DVP–XXXX
X
00V 00Hz
NO.
00W
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
6
ALL
0-000-000-00
Region code
Notes
• Notes about DVD+RWs/DVD+Rs/
DVD+Rs DL, DVD-RWs/DVD-Rs/
DVD-Rs DL, or CD-Rs/CD-RWs
Some DVD+RWs/DVD+Rs/DVD+Rs DL,
DVD-RWs/DVD-Rs/DVD-Rs DL, or CD-Rs/
CD-RWs cannot be played on this player due to
the recording quality or physical condition of the
disc, or the characteristics of the recording device
and authoring software.
The disc will not play if it has not been correctly
finalized. For more information, refer to the
operating instructions for the recording device.
Note that some playback functions may not work
with some DVD+RWs/DVD+Rs/DVD+Rs DL,
even if they have been correctly finalized. In this
case, view the disc by normal playback. Also
some DATA CDs/DATA DVDs created in Packet
Write format cannot be played.
• Music discs encoded with copyright protection
technologies
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
• For player that cannot play images that
contain a copy protection only
Images in DVD-VR mode with CPRM*
protection may not be played if they contain a
copy protection signal, “Copyright lock” appears
on the screen.
* CPRM (Content Protection for Recordable
Media) is a coding technology that protects the
copyright of images.
• Note on DualDiscs
A DualDisc is a two sided disc product which
mates DVD recorded material on one side with
digital audio material on the other side.
However, since the audio material side does not
conform to the Compact Disc (CD) standard,
playback on this product is not guaranteed.
Copyrights
This product incorporates copyright
protection technology that is protected by
U.S. patents and other intellectual property
rights. Use of this copyright protection
technology must be authorized by
Macrovision, and is intended for home and
other limited viewing uses only unless
otherwise authorized by Macrovision.
Reverse engineering or disassembly is
prohibited.
Note on playback operations of
DVDs and VIDEO CDs
Some playback operations of DVDs and
VIDEO CDs may be intentionally set by
software producers. Since this player plays
DVDs and VIDEO CDs according to the disc
contents the software producers designed,
some playback features may not be available.
Also, refer to the instructions supplied with
the DVDs or VIDEO CDs.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
7
Guide to Parts and Controls
For more information, see the pages indicated in parentheses.
Front panel
A [/1 (on/standby) button (20)
E A (open/close) button (20)
B Disc tray (20)
F H (play) button (20)
C Front panel display (9)
G x (stop) button (21)
D
(remote sensor) (16)
Rear panel
L
CENTER
A DIGITAL OUT (COAXIAL) jack (15)
B LINE (RGB) - TV jack (14)
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
8
Front panel display
When playing back a DVD
Playing status
Lights up during
Repeat Play (28)
Current title/chapter or playing
time (23)
Lights up when you can change the angle (21)
When playing back a VIDEO CD with Playback Control (PBC) (23)
Playing status
Current scene or playing time (23)
Lights up during A-B Repeat Play (28)
When playing back a CD, DATA CD (MP3 audio/DivX video), DATA DVD (MP3 audio/DivX
video), or VIDEO CD (without PBC)
Playing status
Current track* (23)
Lights up during
Repeat Play (28)
Playing time (23)
* When playing DivX video files, the current track is not displayed.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
9
Remote
J
m/M
(34)
(scan/slow) buttons
K ZOOM button (21, 44)
L SLOW PLAY/FAST PLAY buttons
(21)
M
N
(audio) button (38)
(subtitle) button (21, 44)
O [/1 (on/standby) button (20)
P 2 (volume) +/– buttons (17)
The + button has a tactile dot.*
Q t (TV/video) button (17)
R PICTURE NAVI (picture navigation)
button (37, 43)
S TIME/TEXT button (23)
T MENU button (23)
U ENTER button (18)
V DISPLAY button (11)
W H (play) button (20)
The H button has a tactile dot.*
X x (stop) button (21)
Y X (pause) button (21)
Z SUR (surround) button (40)
wj
(angle) button (21)
* Use the tactile dot as a reference when operating
the player.
A TV [/1 (on/standby) button (17)
B Z (open/close) button (21)
C Number buttons (17)
The number 5 button has a tactile dot.*
D CLEAR button (27)
E TOP MENU button (23)
F C/X/x/c buttons (21)
G O RETURN (return) button (21)
H
/
(replay/step/advance/
step) buttons (21, 34)
I ./> (previous/next) buttons (21)
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
10
Guide to the Control Menu Display (Magic Pad)
Use the Control Menu to select a function and to view related information. Press DISPLAY
repeatedly to turn on or change the Control Menu display as follows:
, Control Menu display 1
m
Control Menu display 2 (Only for DATA CDs/DATA DVDs without DivX video files)
m
Control Menu display off
Control Menu display
The Control Menu display 1 and 2 will show different items depending on the disc type.
Example: Control Menu display 1 when playing a DVD VIDEO.
Currently playing chapter number*2
Currently playing title number*1
Total number of titles*1
Total number of chapters*2
Control Menu items
Selected item
Function name of
selected Control
Menu item
Operation message
12(27)
18(34)
T
1:32:55
OFF
OFF
SET
ON
PLAY
DVD VIDEO
Playback status
(N Playback,
X Pause,
x Stop, etc.)
Type of disc
being played*3
Playing time*4
Current setting
Options
PROGRAM
ENTER
Quit: DISPLAY
*1 Displays the scene number for VIDEO CDs
(PBC is on), track number for VIDEO CDs/CDs,
album number for DATA CDs/DATA DVDs.
*2 Displays the index number for VIDEO CDs,
MP3 audio track number, or JPEG image file
number for DATA CDs/DATA DVDs. DivX
video file number for DATA CDs/DATA
DVDs.
*3 Displays Super VCD as “SVCD.”
*4 Displays the date for JPEG files.
To turn off the display
Press DISPLAY.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
11
List of Control Menu items
Item
SETUP
QUICK Setup
Use Quick Setup to choose the
desired language of the on-screen
display, the aspect ratio of the TV,
and the audio output signal.
CUSTOM Setup
In addition to the Quick Setup
setting, you can adjust various other
settings.
RESET
Returns the settings in “SETUP” to
the default setting.
Item Name, Function
TITLE/SCENE/TRACK
Selects the title, scene, or track to be
played.
CHAPTER/INDEX
Selects the chapter or index to be
played.
TRACK
Selects the track to be played.
TIME/TEXT
Checks the elapsed time and the
remaining playback time.
Input the time code for picture and
music searching.
Displays the DVD/CD text or the
DATA CD/DATA DVD track/file
name.
ALBUM
Selects the album that contains the
MP3 audio tracks and JPEG image
files to be played.
FILE
Selects the JPEG image file to be
played.
ORIGINAL/PLAY LIST
Selects the type of titles (DVD-VR
mode) to be played, the ORIGINAL
one, or an edited PLAY LIST.
ALBUM
Selects the album that contains DivX
video file to be played.
FILE
Selects the DivX video file to be
played.
PROGRAM
Selects the title, chapter, or track to
play in the order you want.
DATE
Displays the date the picture was
taken by a digital camera.
SHUFFLE
Plays the title, chapter, or track in
random order.
INTERVAL
Specifies the duration for which the
slides are displayed on the screen.
REPEAT
Plays the entire disc (all titles/all
tracks/all albums) repeatedly or one
title/chapter/track/album/file
repeatedly.
EFFECT
Selects the effects to be used for
changing slides during a slide show.
A-B REPEAT
Specifies the parts you want to play
repeatedly.
CUSTOM PICTURE MODE
Adjusts the video signal from the
player. You can select the picture
quality that best suits the programme
you are watching.
SHARPNESS
Exaggerates the outline of the image
to produce a sharper picture.
PARENTAL CONTROL
Set to prohibit playback on this
player.
MODE (MP3, JPEG)
Selects the data type; MP3 audio
track (AUDIO), JPEG image file
(IMAGE), or both (AUTO) to be
played when playing a DATA CD/
DATA DVD.
z Hint
The Control Menu icon indicator lights up in green
when you select any item
t
except “OFF.” (“PROGRAM,” “SHUFFLE,”
“REPEAT,” “A-B REPEAT,” “SHARPNESS”
only). The “ORIGINAL/PLAY LIST” indicator
lights up in green when you select “PLAY LIST”
(default setting). The “CUSTOM PICTURE
MODE” indicator lights up in green when any
setting other than “STANDARD” is selected.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
12
Hookups
Hooking Up the Player
Hookups
Follow steps 1 to 6 to hook up and adjust the settings of the player.
Notes
•
•
•
•
Plug cords securely to prevent unwanted noise.
Refer to the instructions supplied with the components to be connected.
You cannot connect this player to a TV that does not have a SCART input jack.
Be sure to disconnect the mains lead of each component before connecting.
Step 1: Unpacking
Check that you have the following items:
• Remote commander (remote) (1)
• R6 (size AA) batteries (2)
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
13
Step 2: Connecting to your TV
Connect this player to your TV monitor, or projector using an audio/video (SCART) cord. This
connection will use your TV speakers for sound.
INPUT
TV
SCART cord
(not supplied)
to LINE (RGB)-TV
L
CENTER
CD/DVD player
l : Signal flow
SCART input jack
VCR, you may not receive a clear image on the
TV screen.
Be sure to make the connections firmly to
avoid hum and noise.
When using this connection, check that the
TV conforms to S video or RGB signals.
Refer to the operating instructions supplied
with the TV to be connected. Also, when you
set “LINE” to “S VIDEO” or “RGB” under
“SCREEN SETUP” in the Setup Display
(page 51), use a SCART cord that conforms
to each signal.
When connecting to a standard 4:3 screen
TV
Depending on the disc, the image may not fit
your TV screen. To change the aspect ratio,
see page 51.
Notes
• Do not connect a VCR, etc., between your TV and
the player. If you pass the player signals via the
VCR
CD/DVD player
• When you connect the player to your TV via the
SCART jacks, the TV’s input source is set to the
player automatically when you start playback. In
this case, press t (TV/video) on the remote to
return the input to the TV.
When you play a disc recorded in the NTSC
colour system, the player outputs the video
signal or the Setup Display etc. in the NTSC
colour system and the picture may not
appear on the PAL colour system
televisions. In this case, open the tray and
remove the disc.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
14
TV
Connect
directly
Step 3: Connecting to an Audio Component
L
CENTER
Hookups
If your audio component such as an AV amplifier (receiver) has a Dolby*1 Digital, DTS*2, or
MPEG audio decoder and a digital input jack, use this connection. You can enjoy Dolby Digital
(5.1 ch), DTS (5.1 ch) and MPEG audio (5.1 ch) surround effects.
CD/DVD player
to DIGITAL OUT (COAXIAL)
COAXIAL
DIGITAL OUT
Coaxial digital cord
(not supplied)
to coaxial
digital input
[Speakers]
Rear (L)
Rear (R)
Front (L)
Centre
[Speakers]
Front (R)
Audio component with
a decoder
Subwoofer
: Signal flow
z Hint
For correct speaker location, see the operating
instructions supplied with the connected
components.
*1 Manufactured under license from Dolby
Laboratories.
Dolby, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
*2 Manufactured under license under U.S. Patent
#: 5,451,942 & other U.S. and worldwide
patents issued & pending. DTS and DTS Digital
Out are registered trademarks and the DTS
logos and Symbol are trademarks of DTS, Inc.
© 1996-2007 DTS, Inc. All Rights Reserved.
Notes
• After you have completed the connection, make
the appropriate settings in Quick Setup (page 18).
If your audio component has an MPEG audio
decoder function, set “MPEG” to “MPEG” in
AUDIO SETUP (page 54). Otherwise, no sound
or a loud noise will come from your speakers.
• The TVS effects of this player cannot be used
with this connection.
• In order to listen to DTS sound tracks, you must
use this connection. DTS sound tracks are not
output through the LINE (RGB)-TV (SCART)
jack, even if you set “DTS” to “ON” in Quick
Setup (page 18).
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
15
Step 4: Connecting the Mains Lead
Plug the player and TV mains lead (power cord) into a mains.
Step 5: Preparing the Remote
You can control the player using the supplied remote. Insert two R6 (size AA) batteries by
matching the 3 and # ends on the batteries to the markings inside the compartment. When
using the remote, point it at the remote sensor
on the player.
Notes
• Do not leave the remote in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from the sun or a lighting apparatus. Doing so may cause a
malfunction.
• If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage
from battery leakage and corrosion.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
16
Controlling other TVs with the
remote
You can control the sound level, input source,
and power switch of your Sony TV with the
supplied remote.
You can control the sound level, input source,
and power switch of non-Sony TVs as well.
If your TV is listed in the table below, set the
appropriate manufacturer’s code.
TV
Number
buttons
1
While holding down TV [/1, press the
number buttons to select your TV’s
manufacturer’s code (see the table
below).
2
Release TV [/1.
2 +/–
t
Hookups
Controlling Your TV With the
Supplied Remote
Code numbers of controllable TVs
You can control your TV using the buttons
below.
If more than one code number is listed, try
entering them one at a time until you find the
one that works with your TV.
By pressing
You can
Manufacturer
TV [/1
Turn the TV on or off
Code number
Sony
01 (default)
2 (volume) +/– Adjust the volume of the TV
Aiwa
01 (default)
t (TV/video)
Grundig
11
Hitachi
24
Switch the TV’s input source
between the TV and other
input sources
Note
Depending on the connected unit, you may not be
able to control your TV using all or some of the
buttons on the supplied remote.
JVC
33
LG
06
Loewe
06
Panasonic
17, 49
Philips
06, 08
Samsung
06, 71
Sanyo
25
Sharp
29
Thomson
43
Toshiba
38
Notes
• When you replace the batteries of the remote, the
code number you have set may be reset to the
default setting. Set the appropriate code number
again.
• Depending on the connected unit, you may not be
able to control your TV using all or some of the
buttons on the supplied remote.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
17
Step 6: Quick Setup
Follow the steps below to make the minimum number of basic adjustments for using the player.
To skip an adjustment, press >. To return to the previous adjustment, press ..
ENTER
1 Turn on the TV.
2 Press [/1.
3 Switch the input selector on your
5 Press X/x to select a language.
TV so that the signal from the
player appears on the TV screen.
The Setup Display for selecting the
aspect ratio of the TV to be connected
appears.
“Press [ENTER] to run QUICK SETUP”
appears at the bottom of the screen. If this
message does not appear, select
“QUICK” under “SETUP” in the Control
Menu to run Quick Setup (page 50).
The player displays the menu and
subtitles in the selected language.
6 Press ENTER.
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
LINE:
16:9
16:9
4:3 LETTER BOX
4:3 PAN SCAN
4 Press ENTER without inserting a
disc.
The Setup Display for selecting the
language used in the on-screen display
appears.
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
ENGLISH
ENGLISH
FRANÇAIS
DEUTSCH
ITALIANO
ESPAÑOL
NEDERLANDS
DANSK
SVENSKA
7 Press X/x to select the setting that
matches your TV type.
◆ If you have a wide-screen TV or a 4:3
standard TV with a wide-screen mode
• 16:9 (page 51)
◆ If you have a 4:3 standard TV
• 4:3 LETTER BOX or 4:3 PAN SCAN
(page 51)
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
18
8 Press ENTER.
12Press X/x to select the type of
The Setup Display for selecting the type
of video signal output from the LINE
(RGB)-TV jack appears.
16:9
ON
JACKET PICTURE
VIDEO
VIDEO
S VIDEO
RGB
9 Press X/x to select the type of
signal you want to output from the
LINE (RGB)-TV jack.
◆ Video signals
• VIDEO (page 51)
◆ S video signals
• S VIDEO (page 51)
◆ RGB signals
• RGB (page 51)
10Press ENTER.
The Setup Display for selecting the type
of jack used to connect your audio
component such as an amplifier
(receiver) appears.
Is this player connected to an amplifier
(receiver) ?
YES
DIGITAL OUTPUT
NO
11Press X/x to select the type of
jack (if any) you are using to
connect to an audio component,
then press ENTER.
If your audio component has a Dolby
Digital decoder, select “DOLBY
DIGITAL.” Otherwise, select “D-PCM.”
AUDIO SETUP
STANDARD
AUDIO DRC:
DOWNMIX:
DOLBY SURROUND
DIGITAL OUT:
ON
D-PCM
DOLBY DIGITAL:
MPEG:
D-PCM
DTS:
DOLBY DIGITAL
48kHz/96kHz PCM:
48kHz/16bit
Hookups
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
LINE:
Dolby Digital signal you wish to
send to your audio component.
13Press ENTER.
“DTS” is selected.
AUDIO SETUP
AUDIO DRC:
STANDARD
DOWNMIX:
DOLBY SURROUND
DIGITAL OUT:
ON
D-PCM
DOLBY DIGITAL:
MPEG:
PCM
DTS:
OFF
48kHz/96kHz PCM:
OFF
ON
14Press X/x to select whether or
not you wish to send a DTS signal
to your audio component.
If your audio component has a DTS
decoder, select “ON.” Otherwise, select
“OFF.”
15Press ENTER.
Quick Setup is finished. All connections
and setup operations are complete.
If your audio component has an MPEG
audio decoder, set “MPEG” to “MPEG”
(page 54).
If you did not connect an audio
component, select “NO,” then go to step
15.
If you connected an audio component
using coaxial digital cord, select “YES:
DIGITAL OUTPUT.”
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
19
4 Press A on the player, and place a
disc on the disc tray.
Playback
Playing Discs
Depending on the DVD or VIDEO CD, some
operations may be different or restricted.
Refer to the operating instructions supplied
with your disc.
RETURN
(replay)
ZOOM
SLOW PLAY
5 Press H.
The disc tray closes. The player starts
playback (continuous play). Adjust the
volume on the TV or the audio
component.
Depending on the disc, a menu may
appear on the TV screen. For DVD
VIDEOs, see page 23. For VIDEO CDs,
see page 23.
Number
buttons
CLEAR
TOP MENU
Playback side facing down
TIME/TEXT
MENU
ENTER
DISPLAY
(advance)
FAST PLAY
To turn off the player
Press [/1. The player enters standby mode.
z Hint
You can have the player turn off automatically
whenever you leave it in stop mode for more than
30 minutes. To turn this function on or off, set
“AUTO POWER OFF” in “CUSTOM SETUP” to
“ON” or “OFF” (page 52).
Note
1 Turn on your TV.
2 Press [/1.
The player turns on.
3 Switch the input selector on your
TV so that the signal from the
player appears on the TV screen.
◆ When using an audio component
Turn on the audio component and select
the appropriate channel so that you can
hear sound from the player.
Discs created on DVD recorders must be correctly
finalized before they can be played. For more
information about finalizing, refer to the operating
instructions supplied with the DVD recorder.
Notes on playing DTS sound tracks on a
DVD VIDEO
• DTS audio signals are output only through the
DIGITAL OUT (COAXIAL) jack.
• When you play a DVD VIDEO with DTS sound
tracks, set “DTS” to “ON” in “AUDIO SETUP”
(page 54).
• If you connect the player to audio equipment
without a DTS decoder, do not set “DTS” to “ON”
in “AUDIO SETUP” (page 54). A loud noise may
come out from the speakers, affecting your ears or
causing the speakers to be damaged.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
20
Additional operations
To check the position of the buttons below,
see the illustration on page 20.
To
Operation
Press x
Pause
Press X
Resume play after
pause
Press X or H
Go to the next chapter, Press >
track, or scene in
continuous play mode
Press .
Go back to the
previous chapter,
track, or scene in
continuous play mode
Stop play and remove Press Z
the disc
Change the angle
Press
(angle)
during playback.
Press
(angle)
repeatedly to select an
angle number.
Display the subtitle
Press
(subtitle)
during playback.
Press
(subtitle)
repeatedly to select a
subtitle language.
Replay the previous
scene*1
Press
(replay)
during playback
Briefly fast forward
the current scene*2
Press
(advance) during
playback
Magnify the image*3
Press ZOOM
repeatedly. Press
CLEAR to cancel.
*1 All DVDs except for DVD+RWs/DVD+Rs/
DVD+Rs DL and DivX video files.
*2 DVDs and DivX video files only.
*3 Video and JPEG pictures only (except
BACKGROUND pictures). You can move the
enlarged picture using C/X/x/c. Depending
upon the contents of the disc, the zoom function
may be cancelled automatically when the
picture is moved.
Playback quickly or slowly with
sound
You can listen to dialogue or sound while
playing the current scene quickly or slowly.
During playback, press FAST PLAY or
SLOW PLAY.
Playback
Stop
Note
You may not be able to use the Replay or Advance
function with some scenes.
The speed changes when you press either
FAST PLAY or SLOW PLAY.
To return to normal playback
Press H.
Notes
• You can only use this function with DVDs,
VIDEO CDs, or Super VCDs only.
• “Operation not possible” will appear when
maximum or minimum speed is reached.
• During Fast Play and Slow Play mode, you cannot
change angle (page 21), subtitle (page 21), and
the sound (page 38). The sound can only be
changed for VIDEO CDs/Super VCDs.
• Fast Play and Slow Play functions do not work
when playing DTS sound tracks.
• You cannot use Fast Play or Slow Play function
when playing a still picture in DVD-VR mode.
Locking the disc tray (Child Lock)
You can lock the disc tray to prevent children
from opening it.
When the player is in standby mode, press
O RETURN, ENTER, and then [/1 on the
remote.
The player turns on and “LOCKED” appears
on the front panel display. The A and Z
buttons on the player or the remote do not
work while the Child Lock is set.
To unlock the disc tray
When the player is in standby mode, press
O RETURN, ENTER, and then [/1 again.
Note
Even if you select “RESET” under “SETUP” in the
Control Menu (page 50), the disc tray remains
locked.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
21
Resuming Playback from the
Point Where You Stopped the
Disc (Resume Play/Multi-disc
Resume)
The player remembers the point where you
stopped the disc.
z Hint
To play from the beginning of the disc, press x
twice, then press H.
Note
• The resume playback point for the current disc is
cleared when:
– you change the play mode.
– you change the settings on the Setup Display.
– you disconnect the mains lead.
Notes
• For DVD-VR mode, CDs, DATA CDs, and
DATA DVDs the player remembers the resume
playback point for the current disc.
The resume point is cleared when:
– you opened the disc tray.
– you disconnect the mains lead.
– the player enters standby mode (DATA CD/
DATA DVD containing MP3 audio tracks/JPEG
image files only).
• Resume Play does not work during Shuffle Play
and Programme Play.
• This function may not work with some discs.
Storing the point where you
stopped the disc (Multi-disc
Resume) (DVP-NS39 only)
Resuming playback for the
current disc (Resume Play)
z Hints
• To play from the beginning of the disc, press x
twice, then press H.
• To turn off the Multi-disc Resume function, set
“MULTI-DISC RESUME” in “CUSTOM
SETUP” to “OFF” (page 52). Playback restarts at
the resume point only for the current disc in the
player.
The player remembers the point where you
stopped the disc even if the player enters
standby mode by pressing [/1.
1 While playing a disc, press x to
stop playback.
“RESUME” appears on the front panel
display.
2 Press H.
The player starts playback from the point
where you stopped the disc in step 1.
The player stores the point where you stopped
the disc for up to 6 discs and resumes
playback the next time you insert the same
disc. When you store a resume playback point
for the seventh disc, the resume playback
point for the first disc is deleted.
Notes
• “MULTI-DISC RESUME” in “CUSTOM
SETUP” must be set to “ON” (default) for this
function to work (page 52).
• The point where you stopped playing is cleared
when:
– you change the play mode.
– you change the settings on the Setup Display.
• If “MULTI-DISC RESUME” in “CUSTOM
SETUP” is set to “ON” and you playback a
recorded disc such as DVD-RW, the player may
playback other recorded discs from the same
resume point.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
22
Using the DVD’s Menu
Selecting “ORIGINAL” or “PLAY
LIST” in DVD-VR mode
Some DVD-VR (Video Recording) mode
have two types of titles for playback:
originally recorded titles (ORIGINAL) and
titles that can be created on recordable DVD
players for editing (PLAY LIST). You can
select the type of title to be played.
1 Press DISPLAY when the player is
in stop mode.
The Control Menu appears.
2 Press X/x to select
(ORIGINAL/PLAY LIST), then press
ENTER.
The options for “ORIGINAL/PLAY
LIST” appear.
12(27)
18(34)
T
1:32:55
PLAY LIST
PLAY LIST
ORIGINAL
PBC (Playback Control) allows you to play
VIDEO CDs interactively by following the
menu on the TV screen.
When you start playing a VIDEO CD with
PBC functions, the menu for your selection
appears.
Select an item using the number buttons, and
press ENTER. Then, follow the instructions
in the menu for interactive operations (Press
H when “Press SELECT” appears).
Refer to the instructions supplied with the
disc, as the operating procedure may differ
depending on the VIDEO CD.
Playback
A DVD VIDEO is divided into long sections
of a picture or a music feature called “titles.”
Press TOP MENU to select a title you want
when you play a DVD VIDEO which
contains several titles. Press MENU to select
items such as language for the sound and
subtitles when you play a DVD VIDEO that
allows you to do so.
Playing VIDEO CDs With PBC
Functions (PBC Playback)
To return to the menu
Press O RETURN.
z Hint
To play without using PBC, press ./> or the
number buttons while the player is stopped to select
a track, then press H or ENTER.
“Play without PBC” appears on the TV screen and
the player starts continuous play. You cannot play
still pictures such as a menu.
To return to PBC playback, press x twice then
press H.
Checking the Playing Time and
Remaining Time
DVD-VR
3 Press X/x to select a setting.
• PLAY LIST: plays the titles created
from “ORIGINAL” for editing.
• ORIGINAL: plays the titles originally
recorded.
You can check the playing time and
remaining time of the current title, chapter, or
track. Also, you can check the DVD/CD text,
track name, ID3 tag information (MP3
audio), or file name (DivX video) recorded on
the disc.
1 Press TIME/TEXT during playback.
The following display appears.
T 1:01:57
4 Press ENTER.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
Time
information
,continued
23
2 Press TIME/TEXT repeatedly to
Bit rate*
change the time information.
T
The available time information depends
upon the type of disc you are playing.
17:30
128k
Checking the play information of
the disc
To check the DVD/CD text
Press TIME/TEXT repeatedly to display text
recorded on the DVD/CD.
The DVD/CD text appears only when text is
recorded in the disc. You cannot change the
text. If the disc does not contain text, “NO
TEXT” appears.
To check DATA CD/DATA DVD album
name, etc.
By pressing TIME/TEXT while playing MP3
audio tracks on a DATA CD/DATA DVD or
DivX video files on a DATA CD/DATA
DVD, you can display the name of the album/
track/file and the audio bit rate (the amount of
data per second of the current audio track) on
your TV screen.
Bit rate*
T
17:30
JAZZ CONCERT 2008
RIVER SIDE SPOT OF THE WORLD
ID3 album name
* Appears when:
– playing an MP3 audio track on a DATA CD/
DATA DVD.
– playing a DivX video file that contains MP3
audio on a DATA CD/DATA DVD.
Checking the information on the
front panel display
You can view the time information and text
displayed on the TV screen also on the front
panel display. The information on the front
panel display changes as follows when you
change the time information on your TV
screen.
128k
JAZZ
RIVER SIDE
Album name
Track/file name
If an MP3 audio track has an ID3 tag, the
player will display the album name/track title
from the ID3 tag information.
ID3 tag information for MP3 audio track is
displayed when the tracks have ID3 version 1
or ID3 version 2. If there are ID3 version 1
and version 2 tags, ID3 version 2 tag
information has priority.
Note that this player supports ID3 versions
1.0/1.1 and 2.2/2.3.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
24
ID3 track title
When playing a DVD
Playing time of the current
title
When playing a VIDEO CD (without PBC
functions) or CD
Playing time and number of the
current track
,
Remaining time of the current track
,
Remaining time of the
current title
Playing time of the disc
Remaining time of the
current chapter
Text
,
Playing time of the current
chapter
Playback
,
Remaining time of the disc
Text
z Hints
• When playing VIDEO CDs without PBC
functions, the track number, and the index number
are displayed after the text.
• When playing VIDEO CDs with PBC functions,
the scene number, or the playing time are
displayed.
• Long text that does not fit in a single line will
scroll across the front panel display.
• You can also check the time information and text
using the Control Menu (page 11).
Notes
Current title and chapter
number
(returns to top automatically)
When playing a DATA CD (MP3 audio) or
DATA DVD (MP3 audio)
Playing time and number of the
current track
,
• Depending on the type of disc being played, the
DVD/CD text or track name may not be
displayed.
• The player can only display the first level of the
DVD/CD text, such as the disc name or title.
• Playing time of MP3 audio tracks and DivX video
files may not be displayed correctly.
• If you play a disc containing JPEG image files
only, “NO AUDIO DATA” appears when
“MODE (MP3, JPEG)” is set to “AUTO,”
“JPEG” appears when “MODE (MP3, JPEG)” is
set to “IMAGE (JPEG)” in the front panel display.
Track name or ID3 track title
,
Current album and track number
(returns to top automatically)
When playing a DATA CD (DivX video) or
DATA DVD (DivX video)
Playing time of the current file
,
The current file name
,
The current album and file number
(returns to top automatically)
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
25
Various Play Mode
Functions (Programme Play,
3
“TRACK” is displayed when you play
a VIDEO CD or CD.
Shuffle Play, Repeat Play, A-B Repeat
PROGRAM
ALL CLEAR
1. TITLE
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
Play)
You can set the following play modes:
• Programme Play (page 26)
• Shuffle Play (page 27)
• Repeat Play (page 28)
• A-B Repeat Play (page 28)
The play mode is cancelled when:
– you eject the disc.
– the player enters standby mode by pressing [/1.
PROGRAM
ALL CLEAR
1. TITLE – –
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
You can play the contents of a disc in the
order you want by arranging the order of the
titles, chapters, or tracks on the disc to create
your own programme. You can programme
up to 99 titles, chapters, and tracks.
Press DISPLAY.
The Control Menu appears.
2
Press X/x to select
(PROGRAM), then press ENTER.
The options for “PROGRAM” appear.
12(27)
18(34)
T
1:32:55
OFF
OFF
SET
ON
PLAY
DVD VIDEO
Press c.
The cursor moves to the title or track row
“T” (in this case, “01”).
Creating your own programme
(Programme Play)
1
T
––
01
02
03
04
05
Titles or tracks
recorded on a disc
4
Note
Press X/x to select “SET t,” then
press ENTER.
T
C
––
01
02
03
04
05
ALL
01
02
03
04
05
06
Chapters recorded on a disc
5
Select the title, chapter, or track you
want to programme.
◆ When playing a DVD VIDEO
For example, select chapter “03” of title
“02.”
Press X/x to select “02” under “T,” then
press ENTER.
PROGRAM
ALL CLEAR
1. TITLE – –
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
T
C
––
01
02
03
04
05
ALL
01
02
03
04
05
06
Next, press X/x to select “03” under “C,”
then press ENTER.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
26
3
PROGRAM
ALL CLEAR
1. TITLE 0 2 – 0 3
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
––
01
02
03
04
05
◆ When playing a VIDEO CD or CD
For example, select track “02.”
Press X/x to select “02” under “T,” then
press ENTER.
Selected track
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
0:15:30
T
02
––
––
––
––
––
––
––
01
02
03
04
05
Total time of the programmed tracks
6
To programme other titles, chapters,
or tracks, repeat steps 4 to 5.
The programmed titles, chapters, and
tracks are displayed in the selected order.
7
Press H to start Programme Play.
Programme Play begins.
When the programme ends, you can
restart the same programme again by
pressing H.
To cancel all of the titles, chapters, or
tracks in the programmed order
1
Follow steps 1 to 3 of “Creating your own
programme (Programme Play).”
2
3
Press X and select “ALL CLEAR.”
Press ENTER.
Playback
Selected title and chapter
PROGRAM
Follow step 5 for new programming. To
cancel a programme, select “--” under
“T,” then press ENTER.
T
z Hint
You can perform Repeat Play or Shuffle Play of
programmed titles, chapters, or tracks. During
Programme Play, follow the steps of Repeat Play
(page 28) or Shuffle Play (page 27).
Notes
• When you programme tracks on a Super VCD, the
total playing time is not displayed.
• You cannot use this function with VIDEO CDs or
Super VCDs with PBC playback.
Playing in random order (Shuffle
Play)
You can have the player “shuffle” titles,
chapters, or tracks. Subsequent “shuffling”
may produce a different playing order.
1
Press DISPLAY during playback.
The Control Menu appears.
2
Press X/x to select
(SHUFFLE), then press ENTER.
The options for “SHUFFLE” appear.
12(27)
18(34)
T
1:32:55
To return to normal play
Press CLEAR, or select “OFF” in step 3. To
play the same programme again, select “ON”
in step 3 and press ENTER.
PLAY
DVD VIDEO
OFF
OFF
TITLE
CHAPTER
To change or cancel a programme
1
Follow steps 1 to 3 of “Creating your
own programme (Programme Play).”
2
Select the programme number of the title,
chapter, or track you want to change or
cancel using X/x and press c. If you
want to delete the title, chapter, or track
from the programme, press CLEAR.
3
Press X/x to select the item to be
shuffled.
◆ When playing a DVD VIDEO
• TITLE
• CHAPTER
◆ When playing a VIDEO CD or CD
• TRACK
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
27
◆ When Programme Play is activated
• ON: shuffles titles, chapters, or tracks
selected in Programme Play.
4
◆ When playing in DVD-VR mode
• DISC: repeats all the titles of the
selected type.
• TITLE: repeats the current title on a
disc.
• CHAPTER: repeats the current chapter.
Press ENTER.
Shuffle Play starts.
◆ When playing a VIDEO CD or CD
• DISC: repeats all of the tracks.
• TRACK: repeats the current track.
To return to normal play
Press CLEAR, or select “OFF” in step 3.
◆ When playing a DATA CD/DATA DVD
• DISC: repeats all of the albums.
• ALBUM: repeats the current album.
• TRACK (MP3 audio tracks only):
repeats the current track.
• FILE (DivX video files only): repeats
the current file.
z Hints
• You can set Shuffle Play while the player is
stopped. After selecting the “SHUFFLE” option,
press H. Shuffle Play starts.
• Up to 200 chapters in a disc can be played in
random order when “CHAPTER” is selected.
◆ When Programme Play or Shuffle Play
is activated
• ON: repeats Programme Play or Shuffle
Play.
Note
You cannot use this function with VIDEO CDs or
Super VCDs with PBC playback.
Playing repeatedly (Repeat Play)
4
Press ENTER.
Repeat Play starts.
You can play all of the titles or tracks on a
disc, or a single title, chapter, or track
repeatedly.
You can use a combination of Shuffle or
Programme Play modes.
1
Press DISPLAY during playback.
The Control Menu appears.
2
Press X/x to select
(REPEAT), then press ENTER.
The options for “REPEAT” appear.
12(27)
18(34)
T
1:32:55
PLAY
DVD VIDEO
OFF
OFF
DISC
TITLE
CHAPTER
3
Press X/x to select the item to be
repeated.
◆ When playing a DVD VIDEO
• DISC: repeats all of the titles.
• TITLE: repeats the current title on a
disc.
• CHAPTER: repeats the current chapter.
To return to normal play
Press CLEAR, or select “OFF” in step 3.
z Hint
You can set Repeat Play while the player is stopped.
After selecting the “REPEAT” option, press H.
Repeat Play starts.
Notes
• You cannot use this function with VIDEO CDs or
Super VCDs with PBC playback.
• When repeating a DATA CD/DATA DVD which
contains MP3 audio tracks and JPEG image files,
and their playing times are not the same, the sound
will not match the image.
• When “MODE (MP3, JPEG)” is set to “IMAGE
(JPEG)” (page 45), you cannot select “TRACK.”
Repeating a specific portion
(A-B Repeat Play)
You can play a specific portion of a title,
chapter or track repeatedly. (This function is
useful when you want to memorize lyrics,
etc.)
1
Press DISPLAY during playback.
The Control Menu appears.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
28
2
Press X/x to select
(A-B
REPEAT), then press ENTER.
The options for “A-B REPEAT” appear.
12(27)
18(34)
T
1:32:55
PLAY
DVD VIDEO
3
Press X/x to select “SET t,” then
press ENTER.
The “A-B REPEAT” setting bar appears.
A 18 - 1:32:30
B
You can adjust the video signal of the DVD,
VIDEO CD, DATA CD/DATA DVD in
JPEG format, or DATA CD/DATA DVD
containing DivX video files from the player
to obtain the picture quality you want. Choose
the setting that best suits the programme you
are watching. When you select “MEMORY,”
you can make further adjustments to each
element of the picture (colour, brightness,
etc.).
Playback
OFF
SET
OFF
Adjusting the Playback
Picture (CUSTOM PICTURE MODE)
1 Press DISPLAY during playback
4
During playback, when you find the
starting point (point A) of the portion to
be played repeatedly, press ENTER.
The starting point (point A) is set.
A 18 - 1:32:30
B 18 - 1:33:05
(When playing a DATA CD or DATA
DVD with JPEG image files, press
twice).
The Control Menu appears.
2 Press X/x to select
(CUSTOM PICTURE MODE), then
press ENTER.
5
When you reach the ending point
(point B), press ENTER again.
The set points are displayed and the
player starts repeating this specific
portion.
The options for “CUSTOM PICTURE
MODE” appear.
12(27)
18(34)
T
1:32:55
DVD VIDEO
STANDARD
To return to normal play
Press CLEAR, or select “OFF” in step 3.
Notes
• When you set A-B Repeat Play, the settings for
Shuffle Play, Repeat Play, and Programme Play
are cancelled.
• A-B Repeat Play does not work across multiple
titles.
• You may not set A-B Repeat Play for contents in
DVD-VR mode that contains still pictures.
STANDARD
DYNAMIC 1
3 Press X/x to select the setting you
want.
The default setting is underlined.
• STANDARD: displays a standard
picture.
• DYNAMIC 1: produces a bold
dynamic picture by increasing the
picture contrast and the colour
intensity.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
29
• DYNAMIC 2: produces a more
dynamic picture than DYNAMIC 1 by
further increasing the picture contrast
and colour intensity.
• CINEMA 1: enhances details in dark
areas by increasing the black level.
• CINEMA 2: white colours become
brighter and black colours become
richer, and the colour contrast is
increased.
• MEMORY: adjusts the picture in
greater detail.
3
Press ENTER.
The adjustment is saved, and
“BRIGHTNESS” adjustment bar
appears.
4
Repeat step 2 and 3 to adjust
“BRIGHTNESS,” “COLOR,” and
“HUE.”
To turn off the display
Press O RETURN or DISPLAY.
4 Press ENTER.
The selected setting takes effect.
z Hint
When you watch a movie, “CINEMA 1” or
“CINEMA 2” is recommended.
Adjusting the picture items in
“MEMORY”
You can adjust each element of the picture
individually.
• PICTURE: changes the contrast
• BRIGHTNESS: changes the overall
brightness
• COLOR: makes the colours deeper or
lighter
• HUE: changes the colour balance
1
In step 3 of “Adjusting the Playback
Picture,” select “MEMORY” and press
ENTER.
The “PICTURE”
adjustment bar appears.
(
)
C
01:32:55
PICTURE
2
0
ENTER
RETURN
Press C/c to adjust the picture
contrast.
To go to the next or previous picture item
without saving the current setting, press
X/x.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
30
Sharpening the Picture
Locking Discs (CUSTOM
(SHARPNESS)
PARENTAL CONTROL, PARENTAL
CONTROL)
1 Press DISPLAY during playback
(When playing a DATA CD or DATA
DVD with JPEG image files, press
twice).
The Control Menu appears.
2 Press X/x to select
(SHARPNESS), then press ENTER.
Playback
You can enhance the outlines of images to
produce a sharper picture.
You can set two kinds of playback restrictions
for a disc.
• Custom Parental Control
You can set playback restrictions so that the
player will not play inappropriate discs.
• Parental Control
Playback of some DVD VIDEOs can be
limited according to a predetermined level
such as the age of the users. Scenes may be
blocked or replaced with different scenes.
The same password is used for both Parental
Control and Custom Parental Control.
Custom Parental Control
The options for “SHARPNESS” appear.
12(27)
18(34)
T
1:32:55
DVD VIDEO
OFF
1
2
OFF
You can set the same Custom Parental
Control password for up to 40 discs. When
you set the 41st-disc, the first disc is
cancelled.
1
If the disc is playing, press x to stop
playback.
2
3 Press X/x to select a level.
• 1: enhances the outline.
• 2: enhances the outline more than 1.
Insert the disc you want to lock.
Press DISPLAY while the player is in
stop mode.
The Control Menu appears.
3
4 Press ENTER.
Press X/x to select
(PARENTAL CONTROL), then press
ENTER.
The options for “PARENTAL
CONTROL” appear.
The selected setting takes effect.
12(27)
18(34)
T
1:32:55
To cancel the “SHARPNESS” setting
STOP
DVD VIDEO
Select “OFF” in step 3.
ON
PLAYER
PASSWORD
OFF
4
Press X/x to select “ON t,” then
press ENTER.
◆ If you have not entered a password
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
31
The display for registering a new
password appears.
PARENTAL CONTROL
Enter a new 4-digit password,
then press ENTER .
Enter a 4-digit password using the
number buttons, then press ENTER.
The display for confirming the password
appears.
◆ When you have already registered a
password
The display for entering the password
appears.
5
Enter or re-enter your 4-digit password
using the number buttons, then press
ENTER.
“Custom parental control is set.” appears
and then the screen returns to the Control
Menu.
2
z Hint
If you forget your password, enter the 6-digit
number “199703” using the number buttons when
the “CUSTOM PARENTAL CONTROL” display
asks you for your password, then press ENTER.
The display will ask you to enter a new 4-digit
password.
Parental Control (limited
playback)
Playback of some DVD VIDEOs can be
limited according to a predetermined level
such as the age of the users. The
“PARENTAL CONTROL” function allows
you to set a playback limitation level.
1
Follow steps 1 to 3 of “Custom Parental
Control.”
2
Press X/x to select “OFF t,” then press
ENTER.
3
Enter your 4-digit password using the
number buttons, then press ENTER.
To play a disc for which Custom Parental
Control is set
1
Insert the disc for which Custom Parental
Control is set.
The “CUSTOM PARENTAL
CONTROL” display appears.
CUSTOM PARENTAL CONTROL
Custom parental control is already
set. To play, enter your password
and press ENTER .
Press DISPLAY while the player is in
stop mode.
The Control Menu appears.
2
Press X/x to select
(PARENTAL CONTROL), then press
ENTER.
The options for “PARENTAL
CONTROL” appear.
To turn off the Custom Parental Control
function
1
Enter your 4-digit password using the
number buttons, then press ENTER.
The player is ready for playback.
12(27)
18(34)
T
1:32:55
ON
PLAYER
PASSWORD
OFF
3
Press X/x to select “PLAYER t,”
then press ENTER.
◆ If you have not entered a password
The display for registering a new
password appears.
Enter a 4-digit password using the
number buttons, then press ENTER.
The display for confirming the password
appears.
◆ When you have already registered a
password
The display for entering the password
appears.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
32
STOP
DVD VIDEO
4
Enter or re-enter your 4-digit password
using the number buttons, then press
ENTER.
The display for setting the playback
limitation level appears.
5
Press X/x to select “STANDARD,”
then press ENTER.
6
Press X/x to select a geographic area
as the playback limitation level, then
press ENTER.
The area is selected.
When you select “OTHERS t,” select
and enter a standard code in the table on
page 60 using the number buttons.
7
1
2
3
To play a disc for which Parental Control is
set
1
2
Insert the disc and press H.
The display for entering your password
appears.
Enter your 4-digit password using the
number buttons, then press ENTER.
The player starts playback.
Press X/x to select “PASSWORD
t,” then press ENTER.
The display for entering the password
appears.
4
Enter your 4-digit password using the
number buttons, then press ENTER.
5
Enter a new 4-digit password using the
number buttons, then press ENTER.
6
To confirm your password, re-enter it
using the number buttons, then press
ENTER.
To turn off the Parental Control function
Set “LEVEL” to “OFF” in step 8.
Press X/x to select
(PARENTAL CONTROL), then press
ENTER.
The options for “PARENTAL
CONTROL” appear.
Select the level you want using X/x,
then press ENTER.
Parental Control setting is complete.
The lower the value, the stricter the
limitation.
Press DISPLAY while the player is in
stop mode.
The Control Menu appears.
Press X/x to select “LEVEL,” then
press ENTER.
The selection items for “LEVEL” are
displayed.
8
Changing the password
Playback
The selection items for “STANDARD”
are displayed.
Notes
• When you play discs which do not have the
Parental Control function, playback cannot be
limited on this player.
• Depending on the disc, you may be asked to
change the parental control level while playing
the disc. In this case, enter your password, then
change the level. If the Resume Play mode is
cancelled, the level returns to the previous level.
If you make a mistake entering your
password
Press C before you press ENTER and input
the correct number.
z Hint
If you forget your password, remove the disc and
repeat steps 1 to 3 of “Parental Control (limited
playback).” When you are asked to enter your
password, enter “199703” using the number
buttons, then press ENTER. The display will ask
you to enter a new 4-digit password. After you enter
a new 4-digit password, replace the disc in the
player and press H. When the display for entering
your password appears, enter your new password.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
33
Opposite direction
×2b t 1m t 2m t 3m
Searching for a Scene
Searching for a
Particular Point on a
Disc (Scan, Slow-motion Play,
Freeze Frame)
You can quickly locate a particular point on a
disc by monitoring the picture or playing back
slowly.
(step)
(step)
Notes
• Depending on the disc, you may not be able to do
some of the operations described.
• For DATA CDs/DATA DVDs, you can search for
a particular point only on an MP3 audio track or
DivX video file.
Locating a point quickly by
playing a disc in fast forward or
fast reverse (Scan)
Press
m or M
while playing a
disc. When you find the point you want, press
H to return to normal speed. Each time you
press
m or M
during scan, the
scan speed changes. With each press the
indication changes as shown below. Actual
speeds may differ between discs.
Playback direction
×2B t 1M t 2M t 3M
3M (DVD/VIDEO CD/DATA CD*/DATA DVD*
only)
×2B (DVD VIDEO/CD only)
3m (DVD/VIDEO CD/DATA CD*/DATA
DVD* only)
×2b (DVD VIDEO only)
* DivX video only
The “×2B”/ “×2b” playback speed is about
twice the normal speed.
The “3M”/“3m” playback speed is faster
than “2M”/“2m” and the “2M”/“2m”
playback speed is faster than “1M”/
“1m.”
Watching frame by frame
(Slow-motion Play)
Press
m or M
when the player is
in pause mode. To return to normal speed,
press H.
Each time you press
m or M
during Slow-motion Play, the playback speed
changes. Two speeds are available. With each
press the indication changes as follows:
Playback direction
2
y1
Opposite direction (DVD only)
2
y1
The “2 y”/“2
than “1 y”/“1
Note
For DATA CDs/DATA DVDs, this function works
only for DivX video files.
Playing one frame at a time
(Freeze Frame)
When the player is in the pause mode, press
(step) to go to the next frame. Press
(step) to go to the preceding frame
(DVD only). To return to normal playback,
press H.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
34
” playback speed is slower
.”
Notes
• You cannot search for a still picture in DVD-VR
mode.
• For DATA CDs/DATA DVDs, this function
works only for DivX video files.
Searching for a Title/
Chapter/Track/Scene,
etc.
Number
buttons
Searching for a Scene
You can search a DVD by title or chapter, and
you can search a VIDEO CD/CD/DATA CD/
DATA DVD by track, index, file, or scene.
As titles and tracks are assigned unique
numbers on the disc, you can select the
desired one by entering its number. You can
also search for a scene using the time code.
CLEAR
ENTER
DISPLAY
1 Press DISPLAY (When playing a
DATA CD/DATA DVD with JPEG
image files, press twice).
The Control Menu appears.
2 Press X/x to select the search
method.
◆ When playing a DVD
TITLE
CHAPTER
TIME/TEXT
Select “TIME/TEXT” to search for a
starting point by inputting the time code.
◆ When playing a VIDEO CD or Super
VCD without PBC Playback
TRACK
INDEX
◆ When playing a VIDEO CD or Super
VCD with PBC Playback
SCENE
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
35
5 Press ENTER.
◆ When playing a CD
TRACK
The player starts playback from the
selected number.
◆ When playing a DATA CD/DATA DVD
ALBUM
TRACK (MP3 audio tracks
To search for a scene using the time code
(DVD and DivX video files only)
FILE (JPEG image files only)
1
In step 2, select
TIME/TEXT.
Playing time of the current title or file is
selected.
Then, press ENTER.
2
Input the time code using the number
buttons, then press ENTER.
For example, to find the scene at 2 hours,
10 minutes, and 20 seconds after the
beginning, just enter “2:10:20.”
only)
◆ When playing a DATA CD (DivX video
files)/DATA DVD (DivX video files)
ALBUM
FILE
TIME/TEXT
Example: when you select
CHAPTER
“** (**)” is selected (** refers to a
number).
The number in parentheses indicates the
total number of titles, chapters, tracks,
indexes, scenes, albums, or files.
12(27)
18(34)
T
1:32:55
PLAY
DVD VIDEO
Selected row
Notes
3 Press ENTER.
“** (**)” changes to “-- (**).”
12(27)
(34)
T
1:32:55
z Hints
• When the Control Menu display is turned off, you
can search for a chapter (DVD), track (CD/DATA
CD/DATA DVD), or file (DATA CD (DivX
video)/DATA DVD (DivX video)) by pressing
the number buttons and ENTER.
• You can display the first scene of titles, chapters,
or tracks recorded on the disc on a screen divided
into 9 sections. You can start playback directly by
selecting one of the scenes. For details, see
“Searching by Scene (PICTURE
NAVIGATION)” (page 37).
• The title, chapter, or track number displayed is the
same number recorded on the disc.
• You cannot search for a scene on a DVD+RW/
DVD+R/DVD+R DL using the time code.
PLAY
DVD VIDEO
4 Press the number buttons to select
the title, chapter, track, index,
scene, etc. number you want to
search.
◆ If you make a mistake
Cancel the number by pressing CLEAR,
then select another number.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
36
Searching by Scene
(PICTURE NAVIGATION)
You can divide the screen into 9 subscreens
and find the desired scene quickly.
1
2
3
4
5
6
7
8
9
4 Press C/X/x/c to select a chapter,
PICTURE
NAVI
ENTER
RETURN
DISPLAY
1 Press PICTURE NAVI during
playback.
The following display appears.
CHAPTER VIEWER
ENTER
Playback starts from the selected scene.
To return to normal play during setting
Press O RETURN or DISPLAY.
z Hint
If there are more than 9 chapters, titles, or tracks, V
is displayed at the bottom right of the screen.
To display the additional chapters, titles, or tracks,
select the bottom scenes and press x. To return to
the previous scene, select the top scenes and press
X.
Searching for a Scene
title, or track, and press ENTER.
Note
Depending on the disc, you may not be able to select
some items.
2 Press PICTURE NAVI repeatedly to
select an item.
• CHAPTER VIEWER (DVD VIDEO
only): displays the first scene of each
chapter.
• TITLE VIEWER (DVD VIDEO only):
displays the first scene of each title.
• TRACK VIEWER (VIDEO CD/
Super VCD only): displays the first
scene of each track.
3 Press ENTER.
The first scene of each chapter, title, or
track appears as follows.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
37
Sound Adjustments
Changing the Sound
When playing a DVD VIDEO or DATA CD
(DivX video files)/DATA DVD (DivX video
files) recorded in multiple audio formats
(PCM, Dolby Digital, MPEG audio, or DTS),
you can change the audio format. If the DVD
VIDEO is recorded with multilingual tracks,
you can also change the language.
With CDs, DATA CDs, DATA DVDs or
VIDEO CDs, you can select the sound from
either the right or left channel and listen to the
sound of the selected channel through both
the right and left speakers. For example, when
playing a disc containing a song with the
vocals on the right channel and the
instruments on the left channel, you can hear
the instruments from both speakers by
selecting the left channel.
◆ When playing a DVD VIDEO
Depending on the DVD VIDEO, the
choice of language varies.
When 4 digits are displayed, they
indicate a language code. See “Language
Code List” on page 60 to see which
language the code represents. When the
same language is displayed two or more
times, the DVD VIDEO is recorded in
multiple audio formats.
◆ When playing in DVD-VR mode
The types of sound tracks recorded on a
disc are displayed. The default setting is
underlined.
Example:
• 1: MAIN (main sound)
• 1: SUB (sub sound)
• 1: MAIN+SUB (main and sub sound)
◆ When playing a VIDEO CD, CD, DATA
CD (MP3 audio), or DATA DVD (MP3
audio)
The default setting is underlined.
• STEREO: the standard stereo sound
• 1/L: the sound of the left channel
(monaural)
• 2/R: the sound of the right channel
(monaural)
◆ When playing a DATA CD (DivX video)
or DATA DVD (DivX video)
Select one of the displayed audio signal
formats. If “No audio data” appears, the
player does not support the audio signal
format contained in the disc.
1 Press
(audio) during playback.
The following display appears.
1:ENGLISH DOLBY DIGITAL 3/2.1
2 Press
(audio) repeatedly to
select the desired audio signal.
◆ When playing a Super VCD
The default setting is underlined.
• 1:STEREO: the stereo sound of the
audio track 1
• 1:1/L: the sound of the left channel of
the audio track 1 (monaural)
• 1:2/R: the sound of the right channel of
the audio track 1 (monaural)
• 2:STEREO: the stereo sound of the
audio track 2
• 2:1/L: the sound of the left channel of
the audio track 2 (monaural)
• 2:2/R: the sound of the right channel of
the audio track 2 (monaural)
Notes
• While playing a Super VCD on which the audio
track 2 is not recorded, no sound will come out
when you select “2:STEREO,” “2:1/L,” or “2:2/
R.”
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
38
• When playing in DVD-VR mode: If you connect
to an audio component using the DIGITAL OUT
(COAXIAL) jack and want to switch between the
sound tracks, set “DOLBY DIGITAL” to “DPCM” in “AUDIO SETUP” (page 54).
Checking the audio signal
format
You can check the audio signal format by
pressing
(audio) repeatedly during
playback. The format of the current audio
signal (Dolby Digital, DTS, PCM, etc.)
appears as shown below.
Notes
• If “DTS” in “AUDIO SETUP” is set to “OFF,”
the DTS track selection option will not appear on
the screen even if the disc contains DTS tracks
(page 54).
• MPEG audio signals with more than two channels
will appear as shown above (3/2.1, 2/1), but only
the Front (L) and Front (R) signals will be output
from your two front speakers.
Example:
Dolby Digital 5.1 ch
Rear (L/R)
Sound Adjustments
◆ When playing a DVD VIDEO
1:ENGLISH DOLBY DIGITAL 3 / 2 .1
Front (L/R)
+ Centre
LFE (Low Frequency
Effect)
◆ When playing a DivX video file on a DATA
CD or a DATA DVD
Example:
MP3 audio
1: MP3 128k
Bit rate
About audio signals
Audio signals recorded in a disc contain the
sound elements (channels) shown below.
Each channel is output from a separate
speaker.
• Front (L)
• Front (R)
• Centre
• Rear (L)
• Rear (R)
• Rear (Monaural): This signal can be either
the Dolby Surround Sound processed
signals or the Dolby Digital sound’s
monaural rear audio signals.
• LFE (Low Frequency Effect) signal
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
39
To cancel the setting
TV Virtual Surround
Settings (TVS)
When you connect a stereo TV or 2 front
speakers, TVS (TV Virtual Surround) lets
you enjoy surround sound effects by using
sound imaging to create virtual rear speakers
from the sound of the front speakers (L: left,
R: right) without using actual rear speakers.
TVS was developed by Sony to produce
surround sound for home use using just a
stereo TV.
If the player is set up to output the signal from
the DIGITAL OUT (COAXIAL) jack, the
surround effect will only be heard when
“DOLBY DIGITAL” is set to “D-PCM” and
“MPEG” is set to “PCM” in “AUDIO
SETUP” (page 54).
SUR
Select “OFF” in step 2.
◆ TVS DYNAMIC THEATER, TVS DYNAMIC,
TVS WIDE
This mode is effective when the distance
between the front L and R speakers is short,
such as with built-in speakers on a stereo TV.
◆ TVS NIGHT
This feature is useful when you want to hear
the dialogue and enjoy the surround sound
effects of “TVS WIDE” at low volume.
◆ TVS STANDARD
Use this setting when you want to use TVS
with 2 separate speakers.
Notes
• When the playing signal does not contain a signal
for the rear speakers, you cannot hear the
surround effects.
• When you select one of the TVS modes, turn off
the surround setting of the connected TV or audio
component.
• Make sure that your listening position is between
and at an equal distance from your speakers, and
that the speakers are located in similar
surroundings.
• Not all discs will respond to the “TVS NIGHT”
function in the same way.
• The TVS effects do not work when using the Fast
Play or Slow Play functions, even though you can
change the TVS modes.
1 Press SUR during playback.
The following display appears.
TVS DYNAMIC THEATER
2 Press SUR repeatedly to select
one of the TVS sounds.
See the explanations given for each item
in the following section.
• TVS DYNAMIC THEATER
• TVS DYNAMIC
• TVS WIDE
• TVS NIGHT
• TVS STANDARD
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
40
Enjoying MP3 Audio and JPEG
Images
About MP3 Audio Tracks
and JPEG Image Files
MP3 is audio compression technology that
satisfies the ISO/IEC MPEG regulations.
JPEG is image compression technology.
You can play DATA CDs/DATA DVDs that
contain MP3 audio tracks or JPEG image
files.
About playback order of albums,
tracks, and files
Albums play in the following order:
◆Structure of disc contents
Tree 1
You can play back DATA CDs or DATA
DVDs recorded in MP3 (MPEG-1 Audio
Layer III) and JPEG format.
However, this player only plays DATA CDs
whose logical format is ISO 9660 Level 1/
Level 2 or Joliet, and DATA DVDs of
Universal Disk Format (UDF).
Refer to the instructions supplied with the
disc drives and the recording software (not
supplied) for details on the recording format.
Tree 2
Tree 3
Tree 4
Tree 5
ROOT
Note
Enjoying MP3 Audio and JPEG Images
DATA CDs/DATA DVDs that the
player can play
Notes
• The player will play any data with the extension
“.MP3,” “.JPG,” or “.JPEG,” even if they are not
in MP3 or JPEG format. Playing these data may
generate a loud noise which could damage your
speaker system.
• The player does not conform to audio tracks in
mp3PRO format.
• Some JPEG files cannot be played.
• You cannot play MP3 audio tracks/JPEG image
files in DATA CDs/DATA DVDs that contain
DivX video files.
The player may not be able to play some DATA
CDs/DATA DVDs created in the Packet Write
format.
MP3 audio track or JPEG image
file that the player can play
The player can play the following tracks and
files:
– MP3 audio tracks with the extension
“.MP3.”
– JPEG image files with the extension
“.JPEG” or “.JPG.”
– JPEG image files that conform to the DCF*
image file format.
Album
Track or file
* “Design rule for Camera File system”: Image
standards for digital cameras regulated by JEITA
(Japan Electronics and Information Technology
Industries Association).
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
41
When you insert a DATA CD/DATA DVD
and press H, the numbered tracks (or files)
are played sequentially, from 1 through 7.
Any sub-albums/tracks (or files) contained
within a currently selected album take
priority over the next album in the same tree.
(Example: C contains D so 4 is played
before 5.)
When you press MENU and the list of album
names appears (page 43), the album names
are arranged in the following order:
A t B t C t D t F t G. Albums
that do not contain tracks (or files) (such as
album E) do not appear in the list.
z Hints
• If you add numbers (01, 02, 03, etc.) to the front
of the track/file names when you store the tracks
(or files) in a disc, the tracks and files will be
played in that order.
• Since a disc with many trees takes longer to start
playback, it is recommended that you create
albums with no more than two trees.
Playing MP3 Audio
Tracks or JPEG Image
Files
You can play MP3 audio tracks and JPEG
image files on DATA CDs or DATA DVDs.
CLEAR
RETURN
PICTURE
NAVI
MENU
ENTER
DISPLAY
ZOOM
Notes
• Depending on the software you use to create the
DATA CD/DATA DVD, the playback order may
differ from the above illustration.
• The playback order above may not be applicable
if there are more than 200 albums and 300 tracks/
files in each album.
• The player can recognize up to 200 albums (the
player will count just albums, including albums
that do not contain MP3 audio tracks and JPEG
image files). The player will not play any albums
beyond the 200th album.
• Proceeding to the next or another album may take
some time.
z Hint
You can view the disc information while playing
MP3 audio tracks (page 23).
Notes
• DATA CDs recorded in KODAK Picture CD
format automatically start playing when inserted.
• If no MP3 audio track or JPEG image file is
recorded on the DATA CD/DATA DVD, “No
audio data” or “No image data” appears on the
screen.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
42
Selecting an album
1
Press MENU.
The list of albums on the disc appears.
When an album is being played, its title is
shaded.
2
Press X/x to select the album you
want to play.
3
Press H.
Playback starts from the selected album.
To select MP3 audio tracks, see
“Selecting an MP3 audio track”
(page 43).
To select JPEG image files, see
“Selecting a JPEG image file” (page 43).
To go to the next or previous MP3 audio
track
Press > or . during playback. You can
select the first track of the next album by
pressing > during playback of the last
track of the current album.
Note that you cannot return to the previous
album by using ., and that you need to
select the previous album from the album list.
Selecting a JPEG image file
1
After step 2 of “Selecting an album,”
press PICTURE NAVI.
To stop playback
1
2
3
4
5
6
7
8
Press c or C.
9
10
11
12
To turn on or off the display
13
14
15
16
Press x.
To go to the next or previous page
Press MENU repeatedly.
z Hint
Of the selected album, you can select to play only
the MP3 audio tracks, JPEG image files, or both, by
setting “MODE (MP3, JPEG)” (page 45).
Selecting an MP3 audio track
To display additional images, select a
bottom image and press x. To return to a
previous image, select a top image and
press X.
2
Enjoying MP3 Audio and JPEG Images
The image files in the album appear in 16
subscreens. A scroll box is displayed on
the right.
Press C/X/x/c to select the image you
want to view, and press ENTER.
The selected image appears.
1
After step 2 of “Selecting an album,”
press ENTER.
The list of tracks in the album appears.
2
Press X/x to select a track, and press
ENTER.
Playback starts from the selected track.
To stop playback
Press x.
To go to the next or previous JPEG image
file
Press C or c during playback. You can select
the first file of the next album by pressing c
during playback of the last file of the current
album.
Note that you cannot return to the previous
album by using C, and that you need to select
the previous album from the album list.
To rotate a JPEG image
To go to the next or previous page
Press c or C.
To return to the previous display
Press O RETURN.
Press X/x while viewing the image. Each
time you press X, the image rotates
counterclockwise by 90 degrees.
To return to normal view, press CLEAR.
Note that the view also returns to normal if
you press C/c to go to the next or previous
image.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
43
To magnify a JPEG image (ZOOM)
Press ZOOM while viewing the image. You
can enlarge the image up to four times the
original size, and scroll using C/X/x/c.
To return to normal view, press CLEAR.
◆When pressed once (x2)
The image enlarges twice the original size.
◆When pressed twice (x4)
The image enlarges four times the original
size.
To display JPEG image information
Press
(subtitle) while viewing JPEG
image files.
The file name, camera maker/model, date,
time, picture resolution, file size, camera
setting information (ISO speed rating,
Exposure time, F Number, Exposure bias, or
Focal length) of the picture are displayed on
the screen.
is displayed when the picture was taken
using flash.
is displayed when the image is
automatically rotated.
To hide the information, press
(subtitle).
Note that the above information may not
appear depending on the digital camera.
To stop viewing the JPEG image
Press x.
Enjoying JPEG Images as
a Slide Show
You can play JPEG image files on a DATA
CD or DATA DVD successively as a slide
show.
1 Press MENU.
The list of albums on the DATA CD/
DATA DVD appears.
2 Press X/x to select an album.
3 Press H.
The JPEG images in the selected album
start playing as a slide show.
To stop playback
Press x.
Notes
• The slide show stops when X/x or ZOOM is
pressed. To resume the slide show, press H.
• This function does not work if “MODE (MP3,
JPEG)” is set to “AUDIO (MP3)” (page 45).
z Hints
• While viewing JPEG image files, you can set
options such as “INTERVAL” (page 46),
“EFFECT” (page 46), and “SHARPNESS”
(page 31).
• You can view JPEG images files without MP3
audio by setting “MODE (MP3, JPEG)” to
“IMAGE (JPEG)” (page 45).
• The date the picture was taken is displayed beside
“DATE” in the Control Menu (page 11). Note that
no date may appear depending on the digital
camera.
Note
PICTURE NAVI does not work if “AUDIO (MP3)”
is selected in “MODE (MP3, JPEG)” (page 45).
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
44
Viewing a slide show with sound
(MODE (MP3, JPEG))
When JPEG image files and MP3 audio
tracks are placed in the same album, you can
enjoy a slide show with sound.
1
Press DISPLAY during stop mode.
The Control Menu appears.
2
Press X/x to select
(MODE
(MP3, JPEG)), and press ENTER.
The options for “MODE (MP3, JPEG)”
appear.
3
Notes
• This function does not work if the MP3 audio
tracks and JPEG image files are not placed in the
same album.
• If playing time of JPEG image or MP3 audio is
longer than the other, the longer one continues
without sound or image.
• If you play large MP3 track data and JPEG image
data at the same time, the sound may skip. It is
recommended that you set the MP3 bit rate to 128
kbps or lower when creating the file. If the sound
still skips, then reduce the size of the JPEG file.
DATA CD MP3
Enjoying MP3 Audio and JPEG Images
12(27)
18(34)
T
32:55
AUTO
AUTO
AUDIO (MP3)
IMAGE (JPEG)
selected, 600 MP3 audio tracks when “AUDIO
(MP3)” is selected, 600 JPEG image files when
“IMAGE (JPEG)” is selected.
Press X/x to select “AUTO” (default),
and press ENTER.
• AUTO: plays both the JPEG image files
and MP3 audio tracks in the same
album as a slide show.
• AUDIO (MP3): plays only MP3 audio
tracks continuously.
• IMAGE (JPEG): plays only JPEG
image files continuously.
4
Press MENU.
The list of albums on the DATA CD/
DATA DVD appears.
5
Press X/x to select the album that
contains both the MP3 audio tracks
and JPEG images you want to play.
6
Press H.
A slide show starts with sound.
z Hints
• To repeat both MP3 audio tracks and JPEG image
files in a single album, repeat the same MP3 audio
track or album when “MODE (MP3, JPEG)” is set
to “AUTO.” See “Playing repeatedly (Repeat
Play)” (page 28) to repeat the track or album.
• The player recognizes a maximum of 200 albums
regardless of the selected mode. Of each album,
the player recognizes up to 300 MP3 audio tracks
and 300 JPEG image files when “AUTO” is
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
45
Setting the pace for a slide show
(INTERVAL)
Selecting the slides’ appearance
(EFFECT)
You can set the time the slides are displayed
on the screen.
You can select the way the slides are
displayed during a slide show.
1
1
Press DISPLAY twice while viewing a
JPEG image or when the player is in
stop mode.
2
Press X/x to select
then press ENTER.
Press DISPLAY twice while viewing a
JPEG image or when the player is in
stop mode.
The Control Menu appears.
2
Press X/x to select
(INTERVAL), then press ENTER.
(EFFECT),
The options for “EFFECT” appear.
The options for “INTERVAL” appear.
3 ( 12)
4)
1(
29/10/2008
NORMAL
NORMAL
FAST
SLOW 1
SLOW 2
3
3 ( 12)
4)
1(
23/10/2008
DATA CD JPEG
Press X/x to select a setting.
MODE 1
MODE 1
MODE 2
MODE 3
MODE 4
MODE 5
OFF
3
Press ENTER.
Note
Some JPEG files, especially progressive JPEG files
or JPEG files of 3,000,000 pixels or more, may take
longer to display than others, which may make the
duration seem longer than the setting you selected.
Press X/x to select a setting.
The default setting is underlined.
• MODE 1: the images randomly cycle
through the effects.
• MODE 2: the next image slides over the
previous image.
• MODE 3: the image sweeps in from top
to bottom.
• MODE 4: the image sweeps in from left
to right.
• MODE 5: the image stretches out from
the centre of the screen.
• OFF: turns off this function.
The default setting is underlined.
• NORMAL: sets to standard duration.
• FAST: sets a duration shorter than
NORMAL.
• SLOW 1: sets a duration longer than
NORMAL.
• SLOW 2: sets a duration longer than
SLOW 1.
4
4
Press ENTER.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
46
DATA CD JPEG
Enjoying DivX® Videos
About DivX Video Files
DivX® is a video file compression
technology, developed by DivX, Inc. This
product is an official DivX® Certified
product.
You can play DATA CDs and DATA DVDs
that contain DivX video files.
DATA CDs and DATA DVDs that
the player can play
The player can play data that is recorded in
DivX format, and which has the extension
“.AVI” or “.DIVX.” The player will not play
files with the extension “.AVI” or “.DIVX” if
they do not contain a DivX video.
z Hint
For details about playable MP3 audio tracks or
JPEG image files on DATA CDs/DATA DVDs, see
“DATA CDs/DATA DVDs that the player can
play” (page 41).
Notes
• The player may not play a DivX video file when
the file has been combined from two or more
DivX video files.
• The player cannot play a DivX video file of size
more than 720 (width) × 576 (height)/2 GB.
• Depending on the DivX video file, the picture
may be unclear or the sound may skip.
• The player cannot play some DivX video files that
are longer than 3 hours.
Enjoying DivX® Videos
Playback of DATA CDs and DATA DVDs
on this player is subject to certain conditions:
– With DATA CDs/DATA DVDs that
contain DivX video files in addition to MP3
audio tracks or JPEG image files, the player
plays only the DivX video files.
However, this player only plays DATA CDs
whose logical format is ISO 9660 Level 1/
Level 2 or Joliet, and DATA DVDs of
Universal Disk Format (UDF).
Refer to the instructions supplied with the
disc drives and the recording software (not
supplied) for details on the recording format.
DivX video files that the player
can play
About playback order of data on DATA CDs
or DATA DVDs
See “About playback order of albums, tracks,
and files” (page 41). Note that the playback
order may not be applicable, depending on
the software used for creating the DivX video
file, or if there are more than 200 albums and
600 DivX video files in each album.
Note
The player may not be able to play some DATA
CDs/DATA DVDs created in the Packet Write
format.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
47
Playing DivX Video Files
To stop playback
Press x.
To go to the next or previous page
You can play DivX video files on DATA CDs
and DATA DVDs.
MENU
ENTER
RETURN
Press C or c.
To turn the display on or off
Press MENU repeatedly.
Selecting a DivX video file
1
After step 2 of “Selecting an album,”
press ENTER.
The list of files in the album appears.
2
z Hint
You can view the disc information while playing a
DivX video file (page 23).
Notes
• If there are no DivX video files recorded on the
DATA CD/DATA DVD, a message appears to
indicate that the disc is not playable.
• Depending on the DivX video file, the picture
may pause or be unclear. In which case, it is
recommended that you create the file at a lower
bit rate. If the sound is still noisy, MP3 is the
recommended audio format. Note, however, this
player does not conform to WMA (Windows
Media Audio) format.
• Because of the compression technology used for
DivX video files, it may take some time after you
press H (play) for the picture to appear.
• Depending on the DivX video file, the sound may
not match the pictures on the screen.
Selecting an album
1
Press MENU.
A list of albums on the disc appears. Only
albums that contain DivX video files are
listed.
2
Press X/x to select the album you
want to play.
3
Press H.
Playback starts from the selected album.
To select DivX video files, see “Selecting
a DivX video file” (page 48).
Press X/x to select a file, and press
ENTER.
The selected file starts playing.
To stop playback
Press x.
To go to the next or previous page
Press C or c.
To return to the previous display
Press O RETURN.
To go to the next or previous DivX video
file without turning on the above file list
You can select the next or previous DivX
video file in the same album by pressing >
or ..
You can also select the first file of the next
album by pressing > during playback of
the last file of the current album. Note that
you cannot return to the previous album by
using .. To return to the previous album,
select it from the album list.
z Hint
If the number of viewing times is preset, you can
play the DivX video files as many times as the
preset number. The following occurrences are
counted:
– when the mains lead is disconnected
– when the disc tray is opened.
– when another file is played.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
48
3 Press X/x to select “CUSTOM,”
Settings and Adjustments
Using the Setup Display
By using the Setup Display, you can make
various adjustments to items such as picture
and sound. You can also set a language for the
subtitles and the Setup Display, among other
things.
For details on each Setup Display item, see
pages from 50 to 54.
Note
Playback settings stored in the disc take priority
over the Setup Display settings and not all of the
functions described may work.
ENTER
DISPLAY
The Setup Display appears.
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
ENGLISH
ENGLISH
ORIGINAL
ENGLISH
4 Press X/x to select the setup item
from the displayed list:
“LANGUAGE SETUP,” “SCREEN
SETUP,” “CUSTOM SETUP,” or
“AUDIO SETUP.” Then press
ENTER.
The Setup item is selected.
Example: “SCREEN SETUP”
Selected item
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
LINE:
16:9
ON
JACKET PICTURE
VIDEO
Settings and Adjustments
Number
buttons
then press ENTER.
Setup items
1 Press DISPLAY when the player is 5 Press X/x to select an item, then
in stop mode.
press ENTER.
The Control Menu appears.
The options for the selected item appear.
Example: “TV TYPE”
2 Press X/x to select
(SETUP), then press ENTER.
The options for “SETUP” appear.
( 47 )
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
LINE:
16:9
16:9
4:3 LETTER BOX
4:3 PAN SCAN
STOP
DVD VIDEO
Options
QUICK
CUSTOM
RESET
QUICK
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
49
6 Press X/x to select a setting, then
press ENTER.
The setting is selected and setup is
complete.
Example: “4:3 PAN SCAN”
Setting the Display or
Sound Track Language
(LANGUAGE SETUP)
Selected setting
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
LINE:
4:3 PAN SCAN
ON
JACKET PICTURE
VIDEO
“LANGUAGE SETUP” allows you to set
various languages for the on-screen display or
sound track.
Select “LANGUAGE SETUP” in the Setup
Display. To use the display, see “Using the
Setup Display” (page 49).
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
To enter the Quick Setup mode
ENGLISH
ENGLISH
ORIGINAL
ENGLISH
Select “QUICK” in step 3. Follow from step
5 of the Quick Setup explanation to make
basic adjustments (page 18).
To reset all of the “SETUP” settings
◆ OSD (On-Screen Display)
1
Select “RESET” in step 3 and press
ENTER.
Switches the display language on the screen.
2
Select “YES” using X/x.
You can also quit the process and return
to the Control Menu by selecting “NO”
here.
3
Press ENTER.
All the settings explained on pages 50 to
54 return to the default settings. Do not
press [/1 while resetting the player,
which takes a few seconds to complete.
◆ MENU (DVD VIDEO only)
You can select the desired language for the
disc’s menu.
◆ AUDIO (DVD VIDEO only)
Switches the language of the sound track.
When you select “ORIGINAL,” the language
given priority in the disc is selected.
◆ SUBTITLE (DVD VIDEO only)
Switches the language of the subtitle recorded
on the DVD VIDEO.
When you select “AUDIO FOLLOW,” the
language for the subtitles changes according
to the language you selected for the sound
track.
z Hint
If you select “OTHERS t” in “MENU,”
“SUBTITLE,” or “AUDIO,” select and enter a
language code from “Language Code List” on
page 60 using the number buttons.
Note
If you select a language in “MENU,”
“SUBTITLE,” or “AUDIO” that is not recorded on
a DVD VIDEO, one of the recorded languages will
be automatically selected.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
50
Settings for the Display
(SCREEN SETUP)
Choose settings according to the TV to be
connected.
Select “SCREEN SETUP” in the Setup
Display. To use the display, see “Using the
Setup Display” (page 49).
The default settings are underlined.
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
LINE:
16:9
ON
JACKET PICTURE
VIDEO
Note
Depending on the DVD, “4:3 LETTER BOX” may
be selected automatically instead of “4:3 PAN
SCAN” or vice versa.
◆ SCREEN SAVER
The screen saver image appears when you
leave the player in pause or stop mode for 15
minutes, or when you play a CD or DATA
CD (MP3 audio)/DATA DVD (MP3 audio)
for more than 15 minutes. The screen saver
will help prevent your display device from
becoming damaged (ghosting). Press H to
turn off the screen saver.
ON
Turns on the screen saver.
OFF
Turns off the screen saver.
◆ BACKGROUND
◆ TV TYPE
16:9
Select this when you connect a
wide-screen TV or a TV with a
wide mode function.
4:3
LETTER
BOX
Select this when you connect a
4:3 screen TV. Displays a wide
picture with bands on the upper
and lower portions of the
screen.
4:3
Select this when you connect a
PAN SCAN 4:3 screen TV. Automatically
displays the wide picture on the
entire screen and cuts off the
portions that do not fit.
16:9
4:3 LETTER BOX
JACKET
PICTURE
The jacket picture (still picture)
appears, but only when the
jacket picture is already
recorded on the disc (CDEXTRA, etc.). If the disc does
not contain a jacket picture, the
“GRAPHICS” picture appears.
GRAPHICS A preset picture stored in the
player appears.
BLUE
The background colour is blue.
BLACK
The background colour is
black.
Settings and Adjustments
Selects the aspect ratio of the connected TV
(4:3 standard or wide).
Selects the background colour or picture on
the TV screen when the player is in stop mode
or while playing a CD or DATA CD (MP3
audio)/DATA DVD (MP3 audio).
◆ LINE
Selects video signals output from the LINE
(RGB)-TV jack on the rear panel of the
player.
VIDEO
Outputs video signals.
S VIDEO
Outputs S video signals.
RGB
Outputs RGB signals.
Notes
4:3 PAN SCAN
• If your TV does not accept S video or the RGB
signals, no picture will appear on the TV screen,
even if you select “S VIDEO” or “RGB.” Refer to
the instructions supplied with your TV.
• If your TV has only one SCART (EURO AV)
jack, do not select “S VIDEO.”
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
51
◆ PAUSE MODE (DVDs only)
Custom Settings (CUSTOM
Selects the picture in pause mode.
SETUP)
AUTO
The picture, including subjects
that move dynamically, is
output with no jitter. Normally
select this position.
FRAME
The picture, including subjects
that do not move dynamically,
is output in high resolution.
Use this to set up playback related and other
settings.
Select “CUSTOM SETUP” in the Setup
Display. To use the display, see “Using the
Setup Display” (page 49).
The default settings are underlined.
CUSTOM SETUP
AUTO POWER OFF:
ON
AUTO PLAY:
OFF
DIMMER:
BRIGHT
AUTO
PAUSE MODE:
TRACK SELECTION:
OFF
ON
MULTI-DISC RESUME:
Registration Code
DivX:
◆ TRACK SELECTION (DVD VIDEO only)
Gives the sound track which contains the
highest number of channels priority when you
play a DVD VIDEO on which multiple audio
formats (PCM, MPEG audio, DTS, or Dolby
Digital format) are recorded.
OFF
No priority given.
AUTO
Priority given.
Notes
◆ AUTO POWER OFF
Switches the Auto Power Off setting on or
off.
ON
The player enters standby mode
when left in stop mode for more
than 30 minutes.
OFF
Switches this function off.
◆ AUTO PLAY
Switches the Auto Play setting on or off. This
function is useful when the player is
connected to a timer (not supplied).
OFF
Switches this function off.
ON
Automatically starts playback
when the player is turned on by
a timer (not supplied).
• When you set the item to “AUTO,” the language
may change. The “TRACK SELECTION” setting
has higher priority than the “AUDIO” settings in
“LANGUAGE SETUP” (page 50).
• If you set “DTS” to “OFF” (page 54), the DTS
sound track is not played even if you set “TRACK
SELECTION” to “AUTO.”
• If PCM, DTS, MPEG audio, and Dolby Digital
sound tracks have the same number of channels,
the player selects PCM, DTS, MPEG, and Dolby
Digital audio sound tracks in this order.
◆ MULTI-DISC RESUME (DVD VIDEO/
VIDEO CD only) (DVP-NS39 only)
Switches the Multi-disc Resume setting on or
off. Resume playback can be stored in
memory for up to 6 different DVD VIDEOs/
VIDEO CDs (page 22).
ON
Stores the resume setting in
memory for up to 6 discs.
OFF
Does not store the resume
setting in memory. Playback
restarts at the resume point only
for the current disc in the player.
◆ DIMMER
Adjusts the lighting of the front panel display.
BRIGHT
Makes the lighting bright.
DARK
Makes the lighting dark.
Note
If you run Quick Setup, Multi-disc Resume setting
stored in memory may return to the default setting.
◆ DivX
Displays the registration code for this player.
For more information, go to
http://www.divx.com/vod
on the Internet.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
52
◆ DOWNMIX (DVDs only)
Settings for the Sound
(AUDIO SETUP)
“AUDIO SETUP” allows you to set the sound
according to the playback and connection
conditions.
Select “AUDIO SETUP” in the Setup
Display. To use the display, see “Using the
Setup Display” (page 49).
The default settings are underlined.
AUDIO SETUP
AUDIO DRC:
STANDARD
DOWNMIX:
DOLBY SURROUND
DIGITAL OUT:
ON
D-PCM
DOLBY DIGITAL:
MPEG:
PCM
DTS:
OFF
48kHz/96kHz PCM:
48kHz/16bit
◆ AUDIO DRC (Dynamic Range Control)
(DVDs only)
DOLBY
SURROUND
Normally, select this position.
Multi-channel audio signals are
output to 2 channels for enjoying
surround sounds.
NORMAL
Multi-channel audio signals are
downmixed to 2 channels for use
with your stereo.
◆ DIGITAL OUT
Selects if audio signals are output via the
DIGITAL OUT (COAXIAL) jack.
ON
Normally, select this position. When
you select “ON,” see “Setting the
digital output signal” for further
settings (page 54).
OFF
The influence of the digital circuit
upon the analogue circuit is minimal.
Settings and Adjustments
Makes the sound clear when the volume is
turned down when playing a DVD that
conforms to “AUDIO DRC.”
This function affects the output from the
following jacks:
– LINE (RGB)-TV jack
– DIGITAL OUT (COAXIAL) jack only
when “DOLBY DIGITAL” is set to “DPCM” (page 54).
Switches the method for mixing down to 2
channels when you play a DVD which has
rear sound elements (channels) or is recorded
in Dolby Digital format. For details on the
rear signal components, see “Checking the
audio signal format” (page 39). This function
affects the output of the following jacks:
– LINE (RGB)-TV jack
– DIGITAL OUT (COAXIAL) jack when
“DOLBY DIGITAL” is set to “D-PCM”
(page 54).
STANDARD Normally, select this position.
TV MODE
Makes low sounds clear even if
you turn the volume down.
WIDE
RANGE
Gives you the feeling of being
at a live performance.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
53
Setting the digital output signal
Switches the method of outputting audio
signals when you connect a component such
as an audio component or MD deck with a
digital input jack.
For connection details, see page 15.
Select “DOLBY DIGITAL,” “MPEG,”
“DTS,” and “48kHz/96kHz PCM” after
setting “DIGITAL OUT” to “ON.”
If you connect a component that is
incompatible with the selected audio signal, a
loud noise (or no sound) may be heard from
the speakers, risking damage to your ears or
speakers.
◆ DOLBY DIGITAL (DVDs only)
Selects the type of Dolby Digital signal.
◆ DTS
Selects whether or not to output DTS signals.
OFF
Select this when the player is
connected to an audio
component without a built-in
DTS decoder.
ON
Select this when the player is
connected to an audio
component with a built-in DTS
decoder.
◆ 48kHz/96kHz PCM (DVD VIDEO only)
Selects the sampling frequency of the audio
signal.
48kHz/16bit The audio signals of DVD
VIDEOs are always converted
to 48kHz/16bit.
D-PCM
Select this when the player is
connected to an audio
component without a built-in
Dolby Digital decoder. You can
select whether the signals
conform to Dolby Surround
(Pro Logic) or not by making
adjustments to the
“DOWNMIX” item in
“AUDIO SETUP” (page 53).
96kHz/24bit All types of signals including
96kHz/24bit are output in their
original format. However, if the
signal is encrypted for
copyright protection purposes,
the signal is only output as
48kHz/16bit.
DOLBY
DIGITAL
Select this when the player is
connected to an audio
component with a built-in
Dolby Digital decoder.
The analogue audio signals from the LINE RGBTV (SCART) jacks are not affected by this setting
and keep their original sampling frequency level.
Note
◆ MPEG (DVDs only)
Selects the type of MPEG audio signal.
PCM
Select this when the player is
connected to an audio
component without a built-in
MPEG decoder. If you play
multi-channel MPEG audio
sound tracks, only the Front (L)
and Front (R) signals will be
output from your two front
speakers.
MPEG
Select this when the player is
connected to an audio
component with a built-in
MPEG decoder.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
54
, When you are using a SCART cord, be sure
to use one that is fully wired (21-pins).
Additional Information
Troubleshooting
If you experience any of the following
difficulties while using the player, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should
any problem persist, consult your nearest
Sony dealer.
Power
The power is not turned on.
, Check that the mains lead is connected
securely.
Picture
There is no picture/picture noise appears.
The picture does not fill the screen, even
though the aspect ratio is set in “TV TYPE”
under “SCREEN SETUP.”
, The aspect ratio of the disc is fixed on your
DVD.
The picture is black and white.
, Set “LINE” in “SCREEN SETUP” to an
item appropriate for your TV (page 51).
, Depending on the TV, the picture on the
screen becomes black and white when you
play a disc recorded in the NTSC colour
system.
There is no sound.
, Re-connect the connecting cord securely.
, The connecting cord is damaged.
, The player is connected to the wrong input
jack on the audio component (page 15).
, The audio component input is not correctly
set.
, The player is in pause mode or in Slowmotion Play mode.
, The player is in fast forward or fast reverse
mode.
, If the audio signal does not come through
the DIGITAL OUT (COAXIAL) jack,
check the audio settings (page 53).
, While playing a Super VCD on which the
audio track 2 is not recorded, no sound will
come out when you select “2:STEREO,”
“2:1/L,” or “2:2/R.”
, When playing multichannel MPEG audio
soundtracks, only the Front (L) and Front
(R) signal will be output from your two
front speakers.
The sound volume is low.
, The sound volume is low on some DVDs.
The sound volume may improve if you set
“AUDIO DRC” in “AUDIO SETUP” to
“TV MODE” (page 53).
Operation
Additional Information
, Re-connect the connecting cord securely.
, The connecting cords are damaged.
, Check the connection to your TV (page 14)
and switch the input selector on your TV so
that the signal from the player appears on
the TV screen.
, Set “LINE” in “SCREEN SETUP” to an
item appropriate for your system (page 51).
, The disc is dirty or flawed.
, If the picture output from your player goes
through your VCR to get to your TV or if
you are connected to a combination TV/
VIDEO player, the copy-protection signal
applied to some DVD programmes could
affect picture quality.
, The disc is recorded in a colour system that
is different from your TV.
Sound
The remote does not function.
, The batteries in the remote are weak.
, There are obstacles between the remote and
the player.
, The distance between the remote and the
player is too far.
, The remote is not pointed at the remote
sensor on the player.
The disc does not play.
, The disc is turned over.
Insert the disc with the playback side facing
down.
, The disc is skewed.
, The player cannot play certain discs
(page 6).
, The region code on the DVD does not match
the player.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
55
, Moisture has condensed inside the player
(page 3).
, The player cannot play a recorded disc that
is not correctly finalized (page 6).
The MP3 audio track cannot be played
(page 42).
, The DATA CD is not recorded in MP3
format that conforms to ISO 9660 Level 1/
Level 2 or Joliet.
, The DATA DVD is not recorded in MP3
format that conforms to UDF (Universal
Disk Format).
, The MP3 audio track does not have the
extension “.MP3.”
, The data is not formatted in MP3 even
though it has the extension “.MP3.”
, The data is not MPEG-1 Audio Layer III
data.
, The player cannot play audio tracks in
mp3PRO format.
, “MODE (MP3, JPEG)” is set to “IMAGE
(JPEG)” (page 45).
, The DATA CD/DATA DVD contains a
DivX video file.
The JPEG image file cannot be played
(page 42).
, The DATA CD is not recorded in JPEG
format that conforms to ISO 9660 Level 1/
Level 2 or Joliet.
, The DATA DVD is not recorded in JPEG
format that conforms to UDF (Universal
Disk Format).
, The file has an extension other than
“.JPEG” or “.JPG.”
, The image is larger than 3072 (width) ×
2048 (height) in normal mode, or more than
3,300,000 pixels in progressive JPEG.
(Some progressive JPEG files cannot be
displayed even if the file size is within this
specified capacity.)
, The image does not fit the screen (the image
is reduced).
, “MODE (MP3, JPEG)” is set to “AUDIO
(MP3)” (page 45).
, The DATA CD/DATA DVD contains a
DivX video file.
The DivX video file cannot be played.
, The file is not created in DivX format.
, The file has an extension other than “.AVI”
or “.DIVX.”
, The DATA CD (DivX video)/DATA DVD
(DivX video) is not created in a DivX
format that conforms to ISO 9660 Level 1/
Level 2 or Joliet/UDF.
, The DivX video file is larger than 720
(width) × 576 (height).
The album/track/file names are not
displayed correctly.
, The player can only display numbers and
alphabet. Other characters are displayed as
“*”.
The disc does not start playing from the
beginning.
, Programme Play, Shuffle Play, Repeat Play,
or A-B Repeat Play is selected (page 26).
, Resume play has taken effect (page 22).
The player starts playing the disc
automatically.
, The disc features an auto playback function.
, “AUTO PLAY” in “CUSTOM SETUP” is
set to “ON” (page 52).
“Copyright lock” appears and the screen
turns blue when playing in DVD-VR mode.
, Images taken from digital broadcasts, etc.,
may contain copy protection signals, such
as complete copy protection signals, single
copy signals, and restriction-free signals.
When images that contain copy protection
signals are played, a blue screen may appear
instead of the images. It may take a while
when looking for playable images. (For
player that cannot play images that contain
a copy protection only)
Playback stops automatically.
, While playing discs with an auto pause
signal, the player stops playback at the auto
pause signal.
The MP3 audio tracks and JPEG image
files start playing simultaneously.
, “MODE (MP3, JPEG)” is set to “AUTO”
(page 45).
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
56
Some functions such as Stop, Fast Play,
Slow Play, Slow-motion Play, Repeat
Play, Shuffle Play, or Programme Play
cannot be performed.
The disc tray does not open and “LOCKED”
appears on the front panel display.
, Depending on the disc, you may not be able
to do some of the operations above. Refer to
the operating manual that comes with the
disc.
The disc tray does not open and “TRAY
LOCKED” appears on the front panel
display.
The language for the sound track cannot
be changed.
, Try using the DVD’s menu instead of the
direct selection button on the remote
(page 23).
, Multilingual tracks are not recorded on the
DVD being played.
, The DVD prohibits the changing of the
language for the sound track.
The subtitle language cannot be changed
or turned off.
, Contact your Sony dealer or local
authorized Sony service facility.
“Data error” appears on the TV screen
when playing a DATA CD or DATA DVD.
, The MP3 audio track/JPEG image file/
DivX video file you want to play is broken.
, The data is not MPEG-1 Audio Layer III
data.
, The JPEG image file format does not
conform to DCF (page 41).
, The JPEG image file has the extension
“.JPG” or “.JPEG,” but is not in JPEG
format.
, The file you want to play has the extension
“.AVI” or “.DIVX,” but is not in DivX
format, or is in DivX format but does not
conform to a DivX Certified profile.
The angles cannot be changed.
, Try using the DVD’s menu instead of the
direct selection button on the remote
(page 23).
, Multi-angles are not recorded on the DVD
being played.
, The angle can only be changed when the
“
” indicator lights up on the front panel
display (page 9).
, The DVD prohibits changing of the angles.
Additional Information
, Try using the DVD’s menu instead of the
direct selection button on the remote
(page 23).
, Multilingual subtitles are not recorded on
the DVD being played.
, The DVD prohibits the changing of
subtitles.
, Child Lock is set (page 21).
The player does not operate properly.
, When static electricity, etc., causes the
player to operate abnormally, unplug the
player.
5 numbers or letters are displayed on the
screen and on the front panel display.
, The self-diagnosis function was activated.
(See the table on page 58.)
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
57
Self-diagnosis Function
(When letters/numbers appear in the
display)
When the self-diagnosis function is activated
to prevent the player from malfunctioning, a
five-character service number (e.g., C 13 50)
with a combination of a letter and four digits
appears on the screen and the front panel
display. In this case, check the following
table.
C:13:50
First three
characters of
the service
number
Cause and/or corrective
action
C 13
The disc is dirty or recorded
in a format that this player
cannot play (page 6).
, Clean the disc with a
cleaning cloth or check its
format.
C 31
The disc is not inserted
correctly.
, Re-insert the disc
correctly.
E XX
To prevent a malfunction, the
(xx is a number) player has performed the
self-diagnosis function.
, Contact your nearest
Sony dealer or local
authorized Sony service
facility and give the 5character service number.
Example: E 61 10
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
58
Specifications
System
General
Laser: Semiconductor laser
Power requirements:
220 – 240 V AC, 50/60 Hz
Power consumption: 8 W
Dimensions (approx.):
430 × 43 × 206.5 mm
(width/height/depth) incl. projecting
parts
Mass (approx.): 1.70 kg
Operating temperature: 5 °C to 35 °C
Operating humidity: 25 % to 80 %
Outputs
(Jack name: Jack type/Output level/Load
impedance)
DIGITAL OUT (COAXIAL):
Phono jack/0.5 Vp-p/75 ohms
LINE (RGB)-TV:
(AUDIO): SCART jack/2 Vrms/10 kilohms
(VIDEO): SCART jack/1.0 Vp-p/75 ohms
(S VIDEO): SCART jack/Y: 1.0 Vp-p,
C: 0.3 Vp-p (PAL), 0.286 Vp-p (NTSC)/
75 ohms
(RGB): SCART jack/0.7 Vp-p/75 ohms
Supplied accessories
See page 13.
Specifications and design are subject to
change without notice.
Additional Information
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
59
Language Code List
For details, see pages 38, 50.
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
Code Language
Code Language
Code Language
1027
1028
1032
1039
1044
1045
1051
1052
1053
1057
1059
1060
1061
1066
1183
1186
1194
1196
1203
1209
1217
1226
1229
1233
1235
1239
1245
1248
1253
1254
1257
1261
1269
1283
1287
1297
1298
1299
1300
1301
1305
1307
1311
1313
1326
1327
1332
1334
1347
1349
1350
1352
1353
1356
1357
1358
1363
1365
1369
1376
1379
1393
1403
1408
1417
1428
1435
1507
1508
1509
1511
1512
1513
1514
1515
1516
1517
1521
1525
1527
1528
1529
1531
1532
1534
1535
1538
1539
1540
1543
1557
1564
1572
1581
1587
1613
1632
1665
1684
1697
1067
1070
1079
1093
1097
1103
1105
1109
1130
1142
1144
1145
1149
1150
1151
1157
1165
1166
1171
1174
1181
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali;
Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
German
Bhutani
Greek
English
Esperanto
Spanish
Estonian
Basque
Persian
Finnish
Fiji
Faroese
French
Frisian
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Italian
Hebrew
Japanese
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Latvian;
Lettish
1345 Malagasy
1436
1463
1481
1482
1483
1489
1491
1495
1498
1501
1502
1503
1505
1506
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay
Maltese
Burmese
Nauru
Nepali
Dutch
Norwegian
Occitan
(Afan)Oromo
Oriya
Punjabi
Polish
Pashto;
Pushto
Portuguese
Quechua
RhaetoRomance
Kirundi
Romanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sangho
SerboCroatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Wolof
Xhosa
Yoruba
Chinese
Zulu
1703 Not specified
Parental Control Area Code List
For details, see page 32.
Code Area
Code Area
Code Area
Code Area
2044
2047
2046
2057
2070
2079
2090
2092
2115
2165
2174
2109
2248
2238
2254
2276
2304
2363
2362
2376
2390
2379
2427
2424
2436
2489
2501
2149
2499
2086
2528
2184
Argentina
Australia
Austria
Belgium
Brazil
Canada
Chile
China
Denmark
Finland
France
Germany
India
Indonesia
Italy
Japan
Korea
Malaysia
Mexico
Netherlands
New Zealand
Norway
Pakistan
Philippines
Portugal
Russia
Singapore
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
60
Spain
Sweden
Switzerland
Thailand
United
Kingdom
Index
Numerics
16:9 51
4:3 LETTER BOX 51
4:3 PAN SCAN 51
48kHz/96kHz PCM 54
5.1 Channel Surround 15
A
A-B REPEAT 28
Advance 21
ALBUM 36
Album 41
Angle 21
AUDIO 38, 50
AUDIO DRC 53
AUDIO SETUP 53
AUTO PLAY 52
AUTO POWER OFF 52
B
BACKGROUND 51
Batteries 16
C
DVD’s menu 23
DVD-RW 5
E
QUICK 50
Quick Setup 18, 50
EFFECT 46
R
F
Fast forward 34
FAST PLAY 21
Fast reverse 34
FILE 36
Freeze Frame 34
Front panel display 9
Remote 10, 16, 17
REPEAT 28
Repeat Play 28
Replay 21
RESET 50
Resume Play 22
S
LANGUAGE SETUP 50
LINE 51
Locating
a specific point by watching
the TV screen 34
Scan 34
SCENE 35
SCREEN SAVER 51
SCREEN SETUP 51
Searching 34
SETUP 49
Setup Display 49
SHARPNESS 31
SHUFFLE 27
Shuffle Play 27
Slide Show 44
SLOW PLAY 21
Slow-motion Play 34
Speakers
Hooking up 15
SUBTITLE 21, 44, 50
Surround 40
M
T
H
Handling discs 3
Hooking up 13
I
ID3 tag 23
INDEX 35
INTERVAL 46
J
JPEG 5, 41
CD 6, 20
CHAPTER 35
CHAPTER VIEWER 37
Child Lock 21
Connecting 14
Continuous play
CD/VIDEO CD 20
DVD 20
Control Menu 11
CUSTOM 49
CUSTOM PARENTAL
CONTROL 31
CUSTOM PICTURE MODE
29
CUSTOM SETUP 52
MEMORY 30
MENU 50
MODE (MP3, JPEG) 45
MP3 5, 41
MPEG 38, 54
MULTI-DISC RESUME 22,
52
D
O
DATA CD 5, 41, 47
DATA DVD 5, 41, 47
DATE 44
DIGITAL OUT 53
Digital output 54
DIMMER 52
Display
Control Menu Display 11
Front panel display 9
Setup Display 49
DivX® 47, 52
DOLBY DIGITAL 38, 54
DOWNMIX 53
DTS 38, 54
DVD 5, 20
DVD+RW 5, 21
Q
L
On-screen display
Control Menu Display 11
Setup Display 49
ORIGINAL 23
ORIGINAL/PLAY LIST 23
OSD 50
P
PARENTAL CONTROL 31
PAUSE MODE 52
PBC Playback 23
PICTURE NAVIGATION
37, 43
PLAY LIST 23
PROGRAM 26
Programme Play 26
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
TIME/TEXT 23, 35
TITLE 35
TITLE VIEWER 37
TRACK 35
TRACK SELECTION 52
TRACK VIEWER 37
Troubleshooting 55
TV TYPE 51
TVS (TV Virtual Surround)
40
U
Usable discs 6
V
VIDEO CD 5, 20
Z
ZOOM 21, 44
61
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
z To find out useful hints, tips and information about Sony products and services
please visit: www.sony-europe.com/myproduct
Printed on 70% or more recycled paper.
Sony Corporation
Printed in HungarySherwood Manuals
Downloaded
From DvDPlayer-Manual.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement