Panasonic WJ-SX150 Operating Instructions

Panasonic WJ-SX150 Operating Instructions
Matrix Switcher
Operating Instructions
WJ-SX150
OPERATE
Matrix Sw
itcher WJ
-SX
150
In
te
OPERAT
E LED WIL
IF COO
LING FAN L BLINK
MALFUN
CTIONS
llig
en
tS
ec
ur
it
y&
Fi
re
Model No.
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
Fi
re
ENGLISH VERSION
y&
Caution:
Before attempting to connect or operate this product,
please read the label on the bottom.
CAUTION
tS
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
ec
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
ur
it
RISK OF ELECTRIC SHOCK
DO NOT OPEN
en
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
In
SA 1965
te
llig
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
SA 1966
Power disconnection. Unit with or without ONOFF switches has power supplied to the unit
whenever the power cord is inserted into the
power source; however, the unit is operational
only when the ON-OFF switch is in the ON
position. Unplug the power cord to disconnect
the main power for all unit.
For U.S.A
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
FCC Caution: To assure continued compliance, (example use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications
not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
The serial number of this product may be found on the bottom of the unit.
You should note the serial number of this unit in the space
provided and retain this book as a permanent record of your
purchase to aid identification in the event of theft.
Model No.
WJ-SX150
Serial No.
WARNING: To prevent fire or electric shock hazard, do not expose this appliance to rain or moisture. The apparatus shall not be exposed to
dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
2
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
Fi
re
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not use near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
ur
it
y&
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the points
where they exit from the apparatus.
ec
11) Only use attachments/accessories specified by the manufacturer.
In
S3125A
te
llig
en
tS
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-overs.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or objects fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
3
CONTENTS
In
te
llig
en
y&
tS
ec
DETAILED PRODUCT DESCRIPTION .......................... 23
MAJOR OPERATING CONTROLS
AND THEIR FUNCTIONS ............................................. 24
■ WJ-SX150 Matrix Switcher .................................... 24
■ WV-CU360C System Controller
(TERMINAL MODE) .............................................. 26
■ WV-CU360CJ System Controller
(TERMINAL MODE) .............................................. 29
INSTALLATIONS AND SYSTEM CONNECTIONS ........ 33
INSTALLATIONS ............................................................ 34
WARNING ................................................................. 34
■ Mounting into the Rack ......................................... 34
■ Installing the Multiplexer Board ............................ 34
SYSTEM CONNECTION EXAMPLES ............................ 35
■ Basic System Connection ..................................... 35
■ System Expansion Connection ............................. 35
CONNECTIONS .............................................................. 37
■ Connection with the Camera Sites ....................... 37
■ Connections for RS-485 Type Camera ................. 38
■ Connection with the Monitors ............................... 39
■ Connection with the System Controllers ............... 40
■ Connection with the Alarm Sensors ...................... 40
■ Connection with the Alarm Output ........................ 41
■ Connection with Digital Disk Recorder
WJ-HD500 Series ................................................. 41
■ Connection with Digital Disk Recorder
WJ-HD100 Series ................................................. 44
■ Connection with the Time-lapse VCR
(Panasonic Models) .............................................. 45
■ Cable Specifications ............................................. 46
■ Connection with the Time-lapse VCR
(Non-Panasonic Models) ...................................... 46
■ Connection with the PC ........................................ 47
■ Time Adjustment with an External Equipment ...... 47
ur
it
FEATURES OF THE MATRIX SWITCHER SYSTEM ...... 9
MATRIX SWITCHER SYSTEM DESCRIPTIONS ........... 10
■ Crosspoint Switches ............................................. 10
■ Monitoring Mode ................................................... 10
■ System Control ..................................................... 11
■ Example of a SYSTEM with Basic Functions ........ 12
TERMINAL MODE DESCRIPTIONS .............................. 14
■ Log-in/Log-out ...................................................... 14
■ Monitor-related Functions ..................................... 15
■ Camera-related Functions .................................... 16
■ Alarm-related Functions ....................................... 17
■ Timer Event ........................................................... 18
■ System Status Table ............................................. 19
■ Setup Procedures ................................................. 19
■ Extended Functions .............................................. 19
NOTIFICATION ABOUT
PS·DATA CONTROLLER OPERATION ....................... 22
WJ-SX150 SETUP PROCEDURES ................................ 49
SETUP PROCEDURES .................................................. 50
■ Setup Procedures ................................................. 50
■ Description of Setup Procedures ......................... 50
WJ-SX150 SETUP MENU (OSD) .................................... 52
■ Displaying SETUP MENU ..................................... 52
■ Programming SETUP MENU ................................ 52
■ TIME & DATE ........................................................ 52
■ D.S.T. (Daylight Saving Time) ............................... 55
■ SEQUENCE SETUP .............................................. 55
■ ALARM SETUP ..................................................... 56
■ CAMERA TITLE ..................................................... 59
■ RECORDER .......................................................... 60
■ SYSTEM SETUP .................................................... 60
■ OPERATOR REGISTRATION ................................ 62
■ MULTIPLEXER ...................................................... 62
■ MUX CAMERA TITLE ............................................ 63
WJ-SX150 ADMINISTRATOR CONSOLE ..................... 64
■ Description of WJ-SX150 Administrator Console . 64
■ Installation/Uninstallation ...................................... 64
■ The Main Window ................................................. 65
■ Recorder ............................................................... 66
■ Put a File to SX150 ................................................ 67
■ Get a Configuration Data from SX150 .................. 68
■ Tour Sequence ..................................................... 68
■ Group Sequence ...................................................69
■ Timer Event ............................................................70
■ Camera Cleaning ...................................................71
■ Daylight Saving Time/Summer Time ..................... 71
■ Alarm Mode .......................................................... 72
■ Alarm Event .......................................................... 74
■ Alarm Port ..............................................................74
■ Operator Registration ........................................... 75
■ Level Table ........................................................... 76
■ Monitor Selection ...................................................76
■ Auto Login/Logout (Auto Log-in/Log-out) ............. 77
■ Time & Date .......................................................... 77
■ Cable Compensation/VD2/DATA .......................... 78
■ Camera Title ......................................................... 79
■ Data Port ............................................................... 81
■ Multiplexer Mode .................................................. 82
■ Select Setup Data File .......................................... 84
■ Account Manager ..................................................85
■ Communication Port ............................................. 86
Fi
re
IIMPORTANT SAFETY INSTRUCTIONS ......................... 3
CONTENTS ....................................................................... 4
PREFACE .......................................................................... 6
FEATURES ....................................................................... 6
PRECAUTIONS ................................................................. 7
DOCUMENT CONVENTION ............................................. 7
4
OPERATING PROCEDURES (TERMINAL MODE) ....... 87
LOG-IN AND LOG-OUT ................................................ 88
■ Log-in .................................................................... 88
■ Log-out ..................................................................89
■ Auto Log-in ............................................................89
■ Auto Log-out ......................................................... 89
MONITOR SELECTION AND CAMERA SELECTION ... 90
■ Monitor Selection .................................................. 90
■ Priority Lock ...........................................................90
■ Camera Selection ................................................. 91
CAMERA CONTROL ...................................................... 92
■ Lens Control ..........................................................92
■ Pan/Tilt Control ..................................................... 92
■ Program Preset Position ....................................... 93
■ Call Preset Position ............................................... 93
Fi
re
y&
APPENDIX ......................................................................131
COMMUNICATION PROTOCOL ...................................132
■ Command Table ...................................................133
■ Error Code List .....................................................141
WORKSHEETS ..............................................................142
■ Instruction ............................................................142
■ Team Work ...........................................................142
■ Checklist ..............................................................143
SPECIFICATIONS ..........................................................151
STANDARD ACCESSORIES ........................................151
In
te
llig
en
tS
ec
OPERATING PROCEDURES (PS·DATA)......................107
WHEN USING A PS·DATA SYSTEM CONTROLLER ..108
MONITOR CONTROL ....................................................109
■ Monitor Selection .................................................109
■ Priority Lock .........................................................109
RUNNING SEQUENCE ..................................................110
■ Tour Sequence ....................................................110
■ Group Sequence .................................................110
MONITOR DISPLAY CONTROL ...................................111
ALARM CONTROL ........................................................112
■ Alarm Mode .........................................................112
■ Operation during an Alarm Mode ........................112
■ Resetting All the Alarm Inputs .............................112
■ Suspending All the Alarm Inputs .........................112
MULTIPLEXER OPERATIONS (PS · Data)....................113
■ Controlling the Unit with a PS·Data
System Controller ................................................113
TIME-LAPSE VCR CONTROL
[NON-PANASONIC MODELS] (TERMINAL MODE) ..123
■ Controlling the Time-lapse VCR ..........................123
WJ-HD500 SERIES CONTROL (PS·DATA) ..................124
■ Controlling the Recorder with a
PS·Data System Controller ..................................124
WJ-HD100 SERIES CONTROL (PS·DATA) ..................125
■ Controlling the Recorder with a
PS·Data System Controller ..................................125
TIME-LAPSE VCR CONTROL (PS·DATA) ...................126
■ Controlling the Time-lapse VCR
with a PS·Data System Controller ....................... 126
MONITOR DISPLAY WHEN A
VIDEO LOSS OCCURS .................................................127
■ Video Loss Display ..............................................127
■ Camera Switching Pulse Loss Display ................127
TROUBLESHOOTING ...................................................128
ur
it
CAMERA FUNCTION CONTROL ....................................94
■ Camera Setup ........................................................94
■ Camera Function (Shortcut Function) ....................94
■ Changing to Black and White Images ...................95
■ Patrol Learn and Play ............................................95
■ Camera Panning Function .....................................96
CAMERA SITE ACCESSORIES CONTROL ...................97
■ Receiver Control ....................................................97
RUNNING SEQUENCE ....................................................98
■ Tour Sequence ......................................................98
■ Group Sequence ...................................................98
MONITOR DISPLAY CONTROL .....................................99
■ On-screen Display (OSD) Control .........................99
■ On-screen Display (OSD) Position Control ............99
■ System Status Table ............................................100
■ Alarm History Table .............................................101
■ Video Loss History Table .....................................101
ALARM CONTROL ........................................................102
■ Alarm Mode .........................................................102
■ Operating during an Alarm Mode ........................102
■ Operation of an Alarm-related Camera (ACK) ....102
■ Resetting the Alarm Inputs ..................................103
■ Suspending the Alarm Inputs ..............................103
MULTIPLEXER OPERATIONS .....................................104
■ Monitoring the Camera Picture ............................104
EXPANDED FUNCTION .................................................115
WJ-HD500 SERIES CONTROL (TERMINAL MODE) ...116
■ Displaying WJ-HD500 Series SETUP MENU .......116
■ Controlling Digital Disk Recorder
WJ-HD500 Series ................................................116
WJ-HD100 SERIES CONTROL (TERMINAL MODE) ...120
■ Displaying WJ-HD100 Series SETUP MENU .......120
■ Controlling Digital Disk Recorder
WJ-HD100 Series ................................................120
TIME-LAPSE VCR CONTROL
[PANASONIC MODELS] (TERMINAL MODE) ............122
■ Controlling the Time-lapse VCR ..........................122
5
PREFACE
ec
ur
it
y&
Fi
re
Matrix Switcher WJ-SX150 is designed for a surveillance control system, which is composed of 16 cameras,
4 monitors and 4 system controllers.
System controllers are used to operate the surveillance control system.
In combination with Digital Disk Recorder WJ-HD500 Series, *WJ-HD100 Series or a time-lapse VCR, a surveillance system
can be established in a local area.
* To use WJ-HD100 Series or a time-lapse VCR, you need to install Multiplexer Board WJ-SXB151 inside the matrix switcher.
llig
en
Multiple sequence modes: 16 tour sequences and 4 group sequences
Control data and timing pulse (VD2) multiplexed over a coaxial cable
Cable compensation selectable depending on the cable length
Cameras (or images on the monitors) selectable with alarm (sensor)
RS-485 cameras connectable
Multiscreen display, electronic zooming, still spot (multiscreen) picture and multiscreen sequence available with
Multiplexer Board WJ-SXB151
• Disk Recorder WJ-HD500 Series controllable
• Connectable to external devices supporting PS·Data
In
te
•
•
•
•
•
•
tS
FEATURES
6
PRECAUTIONS
• Do not use strong or abrasive detergents when
cleaning the appliance body.
Use a dry cloth to clean the appliance when it is dirty.
When the dirt is hard to remove, use a mild detergent
and wipe gently.
• Refer all work related to the installation of this
product to qualified service personnel or system
installers.
• Do not block the ventilation opening or slots on the
cover.
To prevent the appliance from overheating, place it at
least 5 cm (2 inches) away from the wall.
• Do not operate the appliance beyond its specified
temperature, humidity, or power source ratings.
Use the appliance at temperatures within –10 °C +50 °C (14 °F - 122 °F) and humidity below 90 %.
The input power source for this appliance is 120 V AC
60 Hz.
• Do not drop metallic parts through slots.
This could permanently damage the appliance. Turn
the power off immediately and contact qualified service
personnel for service.
Fi
re
• We recommend that you note down your settings
and save them. Power or battery failure may erase
the settings you enter.
llig
en
tS
ec
• Do not expose the appliance to water or moisture.
Do not try to operate it in wet areas.
Take immediate action if the appliance gets wet. Turn
the power off and refer servicing to qualified service
personnel. Moisture can damage the appliance and
also cause electric shocks.
ur
it
• Handle the appliance with care.
Do not strike or shake, as this may damage the appliance.
y&
• Do not attempt to disassemble the appliance.
To prevent electric shock, do not remove screws or
covers.
There are no user-serviceable parts inside. Contact
qualified service personnel for maintenance.
te
DOCUMENT CONVENTION
In
This operating instructions use the following convention when describing the use and operation of this unit.
Unit: Panasonic Matrix Switcher WJ-SX150
System controller: Panasonic System Controller WV-CU360C or WV-CU360CJ
Recorder: Panasonic Digital Disk Recorder WJ-HD500 Series, WJ-HD100 Series* or a time-lapse VCR* (*Available only
when the multiplexer board is installed).
Receiver: Panasonic Indoor Receiver WV-RC100 or Outdoor Receiver WV-RC150
Multiplexer board: Panasonic Multiplexer Board WJ-SXB151
Notes:
• Text with this appearance is a special instruction, rule, or side comment related to the topic.
• In these operating instructions, WV-CU360C is used for the illustrations and descriptions of the system controller.
7
Fi
re
In
te
llig
en
tS
ec
ur
it
y&
FEATURES OF THE MATRIX
SWITCHER SYSTEM
9
MATRIX SWITCHER SYSTEM DESCRIPTIONS
Matrix Switcher System WJ-SX150 is a surveillance control system, which is composed of cameras, recorders, and this unit
(the matrix switcher).
This system has various functions for surveillance control.
The following are the descriptions about the functions.
■ Crosspoint Switches
SW21
SW31
SW41
SW12
SW22
SW32
SW42
SW13
SW23
SW33
SW43
SW14
SW24
SW34
SW44
ec
ur
it
y&
Fi
re
SW11
te
■ Monitoring Mode
llig
en
tS
All matrix switchers, no matter how complicated and sophisticated they may be, depend on crosspoint switches to perform the
basic operations of the switcher. The crosspoint switches from a rectangular array of rows and columns in which any row may
be connected to any column.
In the figure shown above, the rows are connected to video cameras and the columns are connected to video monitors.
By closing a certain crosspoint switch we may connect any camera to any monitor.
In the example above, by closing switch SW12 the camera 2 is displayed on the monitor 1. Likewise, by closing SW24 camera
4 is displayed on the monitor 2.
In
This system can control up to 16 cameras, 4 monitors, and 4 system controllers.
There are two surveillance ways:
One is the spot mode that associates one camera with one monitor. The other is the sequence mode that sequentially displays
the images through more than one camera.
● Spot Mode
The specified camera images are continuously displayed on a given monitor.
When another camera input is accepted, the images are replaced by new ones.
10
● Sequence Mode
Monitor 1
Dwell time: 2 sec.
Step 1
More than one camera's images are sequentially displayed for a
fixed time.
The illustration shows an example of the sequential display of
images through Camera 2, 4, and 6 on Monitor 1.
Before use, the parameters* of the sequence need to be configured and uploaded to the unit.
* Example: Camera selection, monitor selection, and dwell time
(the time to display each image).
Monitor 1
Dwell time: 2 sec.
Step 2
s
Monitor 1
Dwell time: 2 sec.
Step 3
s
s
Camera 2
Camera 4
Camera 6
■ System Control
System controllers are used to control the equipment connected to this system.
About System Controller
Fi
re
●
●
y&
This matrix switcher system has four data ports: DATA 1 to 4. The ports DATA 1 to 3 supports the terminal mode, and the
DATA 4 port supports both the terminal mode and Panasonic Security Data (PS·Data) Systems. These are the operation mode
of the matrix switcher. When using the DATA 4 port, you can employ either of them. Refer to p. 14 for details of the terminal
mode. Refer to p. 22 for notification about PS·Data System.
Camera control
en
tS
ec
ur
it
As the illustration, this unit sends the control data and VD2 timing pulse to the cameras.
On the contrary, the cameras send the video signal and state signal to the unit.
Control data is supplied via the coaxial cable from the unit, multiplexed with the camera image.
The unit is equipped with the circuit to multiplex or separate the video signal and control data with each channel.
These connections enable the control of the equipment from the system controller.
When using Panasonic RS-485 cameras, the unit can send the separated control data to them.
RS-485 cameras can be installed at longer distance from the matrix switcher than cameras that multiplex the control data.
In
te
llig
Combination camera
Coaxial cable
Video signal
Control signal
Matrix switcher
Multiplexed
data
Sync
signal
Status signal
Timing pulse (VD2)
Every channel is equipped with
multiplexed data and sync
signal.
Each signal functions as the illustrations in the next page.
VD2 provides the timing pulse of the same phase to prevent the unconformity during the switching of the image in a sequence
mode.
11
Signal type
Function
Control signal
Controls camera functions (pan/tilt, zooming, focusing, lens iris, preset position) and camera
site accessories.
Status signal
Shows camera status.
Timing pulse (VD2)
This signal is supplied to the unit to each camera.
Each figure shows the picture status with or without the timing pulse.
VD2 OFF
s
s
ur
it
y&
s
Fi
re
VD2 ON
s
■ Example of a SYSTEM with Basic Functions
tS
ec
The illustration in the next page shows the surveillance system in a parking lot as an example.
Before the connections, the matrix switcher's system configuration* and the recorder's alarm recording setting are necessary.
Example: Operations of cameras and other connected equipment during an alarm input
llig
en
1. The infrared sensor sends an alarm signal to the unit when detecting a car comes in.
2. The unit enters the sequence mode associated with Monitor 1.
At the same time, the unit controls the digital disk recorder to change its recording mode into the alarm-recording mode.
te
Monitor 1 is associated with the following sequence.
In
Displaying Camera 1's image
↓
Displaying Camera 4's image (Preset Position 1)
↓
Camera 4 moves from preset position 1 to 2 according to the sequence setting.
Displaying Camera 4's image (Preset Position 2)
↓
Controlling AUX 1 and 2 (The gate will open and the lamp will light up.)
↓
Displaying Camera 5's image
12
Monitor 2 displays Camera 6's image consistently in the spot mode.
Operators will observe the parking lot by looking at these images on a monitor in a management office.
Receiver
Camera 1
Camera 5
Camera 4
Aux 1
Preset
position 1
Preset
position 2
Sensor
Aux 2
ec
ur
it
y&
Fi
re
Camera 6
Recorder
t
t
Alarm
tS
Matrix switcher
t
Alarm 3
OPERATE
OPERATE LED WILL BLINK
IF COOLING FAN MALFUNCTIONS
Matrix Switcher WJ-SX
te
s
Monitor 1
llig
en
Sequence mode
s
s
s
In
Gate
opens.
(Aux 1)
Camera 1
Dwell time : 1 s
Camera 4/position 1
Dwell time : 3 s
Lamp
lights up.
(Aux 2)
Camera 5
Dwell time : 30 s
Camera 4/position 2
Dwell time : 2 s
Monitor 2
s
Alarm
mode
s
s
Camera 6
s
s
Alarm recording mode
* To use WJ-HD100 Series or a time-lapse VCR as a recorder, you need to install a Multiplexer board.
13
s
TERMINAL MODE DESCRIPTIONS
ation conflict.
In the terminal mode, each external device (such as a camera, monitor, system controller, or a recorder, etc.) has the
name and number (Camera 1, etc.). When you control a
device, you are to select the device number and execute the
selection. For example, before controlling Camera 1, you will
press the numeric button 1, and then press the CAM (SET)
button. Each operator has a level and priority. When you try
to control a device beyond the level and priority, the PROHIBITED or BUSY indicator will light up to inform you that you
cannot control it.
Level Setting
16 operators are classified in the level from 1 (the highest) to
3 (the lowest).
A higher-level operator can control more functions.
Password Setting
Up to 5 digit numbers can be registered as a password.
When an operator logs in, the system identifies the operator
ID and password by comparing the registered data.
If they are correct, the operator can control the system.
■ Log-in/Log-out
y&
Priority Setting
The system classifies the operators in priority from 1 to 16.
This setting includes the control coverage that is configured
by level, and the priority in case of the conflict with the samelevel operator.
ur
it
Operable Cameras and Sequences
This setting assigns each operator the cameras and
sequences operable by the level.
Notes:
• Each operator's ID, password, level and priority need to
be configured in WJ-SX150 Administrator Console.
• Log-in/log-out is configurable in SETUP MENU and WJSX150 Administrator Console.
• The level and priority are assigned to each operator.
Operators cannot control the system beyond the assignment.
Even within the level and priority, a device controlled by
a higher-level operator is not operable.
• Manual log-in/log-out or auto log-in/log-out is assignable
to data ports DATA 1 to 4.
en
tS
ec
Log-in/log-out has two ways: One is the manual log-in/log-out
and the other is auto log-in/out.
Through the auto log-in, an operator can login the system
without entering a password, after turning the power on.
Through the auto log-out, an operator can logout of the system when not operating the system for a fixed time.
The way of log-in/log-out and the time for auto log-out is configurable when setting up the system.
When configuring the auto log-in, it is necessary to assign an
operator ID to each data port.
Fi
re
Before starting the system operation, it is necessary to input
an operator ID and a password from a system controller.
The system identifies the operator ID and password by comparing the registered data. If the ID and password are correct, the system will enter the operation mode.
This identification is called log-in. On the contrary, the termination of the system operation is called log-out.
llig
● Operator Registration
In
te
When operating the system, the operator registration is necessary.
Up to 16 operators can be registered and filed by their operator IDs.
They are registered in WJ-SX150 Administrator Console.
The following are the properties, which can prevent the oper-
• Description of Operator Registration
Operator 1 Operator 2 Operator 3 Operator 4 Operator 5 Operator 6
14
Level Table
SX150 Setup
Camera Setup
Alarm History Display
•••
Video Loss History Display
Operator n (Max 16) System Status Display
Single Alarm Reset
All Alarm Reset
–
ID
150
1
100
101
102
103
Password
150
12345
100
101
102
103
–
Level
1
1
1
1
2
3
–
Priority
1
2
3
4
5
6
–
Camera Operation
1
1
1
1
1
1
–
Items operable by
the level are set to
ON.
Camera Operation Level
1: This level can select and control the camera.
2: This level can only select the camera.
3: This level can neither select nor control the camera.
■ Monitor-related Functions
STILL* (Still spot** or still multiscreen display is activated.)
* ”STILL” appears when a Multiplexer board is installed
inside the matrix switcher.
**Available only during playback
The following functions related to monitors are configurable.
Clock
08/21/2001 6:50:08 PM
Note: When pressing the associated numeric button (1 to
5) while holding down the OSD button, information is
turned on or off.
Monitor status
● The Display Position
M1
K 1 T01
C 01 c am era title
The display position of the information is adjustable with the
joystick on the system controller.
ALARM10*
Event
Camera title
● Priority Lock
● Monitor Selection
Fi
re
Priority lock is the function to prevent other operators' control of a monitor even after the system log-out.
While the priority lock is active, the monitor is operable by
the locking operator and higher-priority operators.
y&
It is necessary to select a monitor when controlling the
monitor-related functions, such as camera images or
SETUP MENU.
● Sequence Mode
● Information Displayed on the Monitors
ec
Time and Date
Time and date are displayed.
The date display is selectable from five patterns, and the
time display is selectable from 24- or 12- hour system.
Camera images are displayed for a fixed time, and they are
sequentially switched.
The change from a tour sequence into the spot mode is
also possible.
Before use, the parameters of the sequence, such as a
camera or monitor selection and dwell time need to be configured.
There are two sequences:
• Tour sequence
• Group sequence
ur
it
The following information is displayed on monitors.
llig
en
tS
The date display pattern (Example: August 21, 2001)
21/08/2001
08/21/2001
21/Aug/2001
2001/08/21
Aug/21/2001
Tour Sequence
The images through Camera 1 to 16 are displayed on a
given monitor in the desired sequence.
In
te
Camera Title
The camera number and characters (up to 20) can be configured as a camera title.
The title is displayed in one line.
Monitor Status
The following status is displayed in one line.
Mn (Monitor number)*
Kn (Controller number)*
Tnn (Monitor mode: the example shows the tour
sequence)*
* "n" is the number.
Event
The information related to system operation is displayed.
An alarm control, alarm suspension, and timer event are the
example.
ALARMnn (The alarm is operating.)
ALARMnn ACK (The alarm has been acknowledged.)
Tnn (Timer event: tour sequence number)
LOSS CHnn (the video loss channel number)
ALM SUSPENDED (The alarm is suspended.)
15
CH1
CH2
CH3
A tour sequence is consisted of 16 steps and up to 16
sequences are configurable.
Up to 30 seconds are selectable as each step's dwell time.
Each step can call the desired preset position of a camera
to be displayed.
In each step, the desired preset position of a camera can
be called and displayed.
Tour sequences are configurable in SETUP MENU and WJSX150 Administrator Console.
Focus
This setting adjusts the lens focus.
An auto-focus camera can automatically adjust the focus.
Zoom
This setting adjusts the lens zoom rate.
Group Sequence
Group sequence is a function to display up to 4 tour
sequences in a group on up to 4 monitors. More than one
sequences can be activated at one time by registering
each tour sequence in a group.
Up to 4 tour sequences can be registered in a group.
Iris
This setting adjusts the lens iris .
● Pan/Tilt Head Control
Notes:
• Up to 4 group sequences are configurable in WJ-SX150
Administrator Console. The configuration in the matrix
switcher's SETUP MENU is unavailable.
• The black picture is displayed when the following are
included in a tour or group sequence: a camera channel without image or the image restricted to the operator.
Fi
re
Pan/Tilt
Camera rotates on the pan/tilt heads.
There are two ways of control:
• Manual control by the joystick
The joystick on the system controller can control a camera's pan/tilt head.
• Preset position control
Entering preset position number can automatically
rotate the camera to the desired position.
It is necessary to register a camera's preset position
numbers.
The specified cameras support the registration during
the pan/tilt head control.
Group sequence 1
Monitor 2
Tour 7
Monitor 3
y&
Tour 2
Monitor 4
Notes:
• Depending on the system components, the specified
combination cameras are not operable.
• The speed varies depending on cameras.
• Some cameras' pan/tilt speeds cannot be controlled by
the joystick.
(Refer to the camera's operating instructions for
details.)
ec
Monitor 1
Tour 5
ur
it
Tour 1
tS
● Multiscreen Display (4, 9, and 16 Screens)
llig
■ Camera-related Functions
en
With a recorder, more than one camera images can be displayed in 4, 9, and 16 multiscreen segments.
Refer to p. 115 EXPANDED FUNCTION for details.
te
This system can operate the following camera-related functions.
In
Notes:
• When operating the motorized zoom lens, a combination camera is necessary.
• A motorized zoom lens needs to be installed on a camera. Confirm the system components.
Sequence Mode
The camera turns in the sequence of preset positions in
numerical order.
Sort Mode
The camera turns in the sequence of preset positions
counterclockwise from pan/tilt starting point.
The camera needs to be selected when controlling the
camera-related functions such as a lens zoom, pan/tilt
head, or spot image of a camera.
Patrol Learn
The combination camera can learn and reproduce a routine
of manual operation.
There are two ways of patrol learn:
• Learning during the operation
• Configuration in the camera's SETUP MENU
● Operating Zoom Lens
● Housing Control
Note: Make sure that the lens selection switch (DC/VIDEO)
is set to DC.
The wiper or defroster of the camera housing can be controlled.
● Camera Selection
16
Auto Pan
The camera automatically turns within the preset panning
range.
● External Equipment Control
Notes:
• The images cannot be displayed while cleaning the
camera. Use this function when continuous surveillance
is not necessary, such as after-hours time.
• Cameras which are operating or being in the sequence
mode are not cleaned.
• Camera selection will immediately stop the camera
cleaning.
• If noise remains in the monitor even after the camera
cleaning, there can be a malfunction. Stop using the
camera and consult qualified service personnel.
When the camera is connected via a receiver, the external
equipment connected to the receiver can be controlled.
● Controllable Camera-related Functions
The control is conducted while watching the camera
images on the monitor.
• Changing to black and white pictures
• Camera function (Shortcut function)
Note: The specified cameras can control each function.
Confirm the functions of the connected cameras and
external devices.
■ Alarm-related Functions
Changing to Black and White Pictures
Color images are changeable to black and white images.
This function is intended for surveillance in a dark place
such as an underground parking lot.
Fi
re
y&
ec
● Camera Title
Notes:
• The camera (or tour sequence) and monitor need to be
associated with the alarm number through the configuration in SETUP MENU (OSD) or WJ-SX150
Administrator Console.
• The mode is selectable and configurable in SETUP
MENU (OSD) or WJ-SX150 Administrator Console.
• Even in the alarm mode, pressing the ACK button can
control the camera's pan/tilt, zoom, focus and lens iris.
• When a recorder is connected to the matrix switcher,
the alarm-related recording of the camera images is
possible.
ur
it
Camera Function (Shortcut Function)
The frequently-used functions are registered with the camera function button.
Pressing the button can activate the registered functions.
Refer to the camera's operating instructions for details on
the registered functions.
This unit is equipped with 16 alarm input connectors. When
an alarm input signal is accepted via one of them, the
alarm-associated spot image or tour sequence image is
displayed on the monitor. With the alarm image on the monitor, the unit notifies you of the alarm information with
"ALARM nn (nn is the alarm number)."
There are two ways to display the alarm-associated image:
• Sequence mode
• Hold mode
en
tS
The titles for camera identification, which are displayed on
the monitor, can be registered.
For example, if a camera setting place is registered as a
camera title, operators can be informed where the image is
recorded.
The title is displayed in one line.
• Description about sequence mode and hold mode
In
te
llig
The available character numbers:
20 (camera number and the characters)
The available characters:
ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijkl
mnopqrstuvwxyz0123456789!"#$%&'()=+*_:;,. */?
Notes:
• Camera title is configurable in SETUP MENU and WJSX150 Administrator Console.
• User font characters can be made through WJ-SX150
Administrator Console.
Alarm
input 1
Sequence
mode
17
ALARM 01
Alarm
input 2
ALARM 05
ALARM 02
Dwell time
Automatically replaces
the alarm image
Alarm
input 1
● Camera Cleaning
When using a combination camera, noise can occur on the
monitor after the long-term use.
In this case, the camera needs to be cleaned.
Camera cleaning is configurable to be conducted at the
designated day and time.
The cleaning time is approximately 30 seconds per camera.
Camera image
Alarm
input 5
Alarm
input 5
Alarm
input 2
Hold mode
Camera image
ALARM 01
ALARM 05
Alarm reset operations
Time
● Sequence Mode
● Video Loss History Table
In the sequence mode, the unit displays the initial alarm
image on the monitor until the dwell time ends, even when
another alarm input is accepted. When the dwell time ends,
the unit automatically replaces the alarm image with the
next one.
While the unit's power is ON, the video signal loss from a
camera or a recorder can occur by cable disconnection,
etc.
In this case, video loss history will be reserved in the system, and this table will display the history.
The loss order, date, time, CAMERA IN number and event
can be identified.
Up to 100 item can be reserved, and they are overwritten
from the oldest, after more than 100 item have occurred.
● Hold Mode
In the hold mode, the unit continues to display the initial
alarm image until the alarm reset. With the alarm image on
the monitor, the unit notifies you that more than one alarm
input is accepted with "*" next to "ALARM nn (nn is the
alarm number)."
As well as the video loss history, the date of the loss and
recovery, the camera number and the loss status are displayed on the table.
● Alarm Reset
Fi
re
Notes:
• When turning off the unit, all the history will be deleted.
• Alarm history can also be identified on the PC.
y&
The built-in timer automatically resets the alarm operation
after the time specified in WJ-SX150 Administrator Console.
After the reset, the monitor displays and the sequence will
return to the state before the alarm input.
● Alarm Suspension
en
● Alarm History Table
In
te
llig
This table displays the alarms that have occurred in the
past.
The alarm order, date, time, alarm number and event can
be identified.
Up to 100 item can be reserved, and they are overwritten
from the oldest, after more than 100 item have occurred.
Notes:
• When turning off the unit, all the history will be deleted.
• Alarm history can also be identified on the PC.
ALARM HISTORY
NO
016
015
014
013
012
011
010
009
008
007
18
YYYY/MM/DD
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
VIDEO LOSS HISTORY
YYYY/MM/DD
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
HH:MM:SS
18:59:08
18:58:08
18:57:08
18:55:08
18:54:08
18:53:08
18:53:00
18:52:08
18:51:08
18:50:08
CH
03
14
09
07
08
16
09
14
06
01
1 of 2
EVENT
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
RECOVER
RECOVER
LOSS
LOSS
LOSS
LOSS
LOSS
LOSS
LOSS
RECOVER
tS
ec
Even when an alarm signal is input, the system will deactivate the alarm input and the alarm mode.
When the alarm suspension is active, "ALM SUSPENDED"
will appear on the monitor.
NO
012
011
010
009
008
007
006
005
004
003
ur
it
Note: When more than one alarm input has been accepted,
only the newest can be reset.
HH:MM:SS
18:59:08
18:58:08
18:57:08
18:55:08
18:54:08
18:53:08
18:53:00
18:52:08
18:51:08
18:50:08
ALARM
03
03
03
07
07
07
09
09
06
06
1 of 2
EVENT
ALARM
ACK
RESET
ALARM
ACK
RESET
ALARM
RESET
ALARM
ACK
■ Timer Event
The built-in timer can automatically start or end the
sequence or spot mode on the specified days, which is
configurable in WJ-SX150 Administrator Console.
The available operations:
Tour sequence and spot mode
The available timer events:
Up to 30
Note: When displaying SETUP MENU while timer event is
operating, the operation will stop.
■ System Status Table
■ Extended Functions
The current system status can be identified.
The continuous display becomes possible by the OSD setting.
If a recorder is connected to the matrix switcher, the following will be available.
● Recorder Connection
SYSTEM STATUS
MON
1
2
3
4
CAM
01
02
04
16
MODE
T01
SPOT
ALARM
CAM
KB
K1
K2
K4
PC
OPE
1
2
4
30
The time-lapse recording and playback of all the camera
images connected to the unit are possible.
Each camera's image and camera ID are recorded.
You can search and play back the desired camera's image
by the camera ID.
The time-lapse recording is conducted as following.
PRI
16
2
1
1
Camera1
MON: Monitor's unit address number
CAM: Camera No.
MODE: Operation mode
KB: Controller's unit address number
OPE: Operator number
PRI: Priority
Camera 2
Camera 3
Camera 4
Camera 5
t
y&
t
Fi
re
Start
ur
it
The operations are conducted with the buttons on the
recorder, system controller or PC.
• The setup of the recording device
• The start of the playback
• The stop of the playback
• The playback of the recorded images (the multiscreen
display, still spot picture or still multiscreen picture,
etc.)
ec
■ Setup Procedures
In
te
llig
en
tS
To use the unit, it is necessary to configure the system
through the following setup procedures:
• OSD setup with an active monitor and system controller
The basic parameters are configurable to operate the
unit.
• WJ-SX150 Administrator Console with the PC
The setup utility can configure all the functions of the
unit.
Refer to p. 52 WJ-SX150 SETUP MENU (OSD) and p. 64
WJ-SX150 ADMINISTRATOR CONSOLE for details.
19
• The search for the recorded image (the search by the
camera ID, or the recorded time and date)
• Forward or backward search
• Forward of backward field advance
• Fast-forward
• Rewind
• Index
Refer to each device's operating instructions for details.
●Multiplexer Board Function
To use WJ-HD 100 Series or a time-lapse VCR as a recorder, you need to install a multiplexer board inside the matrix switcher.
With the multiplexer board installation, the following will be available.
• Multiscreen display
More than one camera images can be displayed in 4, 9, and 16 multiscreens.
The sequence output is also available.
As the sequence output, the following are configurable in WJ-SX150 Administrator Console.
• The images are switched within 4 multiscreens. (QUAD)
• The images are displayed in 4 multiscreens, and the images of Camera 4 to 16 are displayed in the sequence mode, at the
right bottom of the monitor.
The images of Camera 1 to 3 are fixed.
(3+1→2S)
Fi
re
• The images are displayed in 9 multiscreens, and the images of Camera 9 to 16 are displayed in the sequence mode, at the
right bottom of the monitor.
The images of Camera 1 to 8 are fixed.
(8+1→2S)
CH1 to CH8 are fixed.
y&
CH1 to CH3 are fixed.
CH9 to CH16 are in a
sequence mode.
ec
ur
it
CH4 to CH16 are in a
sequence mode.
tS
Notes:
• The black image will be displayed for a camera channel which is not connected to the camera.
• Even during the multiscreen display, pressing the camera number can display the camera's image in the spot mode.
te
llig
en
• Still display
The desired image can be displayed in a still picture.
Live images can be displayed in multiscreen display.
Playback images can be displayed in spot/multiscreen display.
"STILL" will appear on the active monitor.
In
• Zoom
The desired image on the monitor can be zoomed up to two fold.
Note: This function is available only when a playback image is displayed in a spot picture.
• Alarm priority mode
When an alarm is activated and the alarm signal is input to the unit, the camera channel with the alarm input will be recordable
according to the configuration in SETUP MENU and WJ-SX150 Administrator Console.
The following are configurable as the recording mode when the alarm is activated:
• The camera channel with the alarm input is given recording priority. (ALM-PRI)
• Only the camera channel with the alarm input is recorded. (ALM-ONLY)
• Up to 4 camera channels are assigned to an alarm input to record the images by priority. (GROUP)
Notes:
• The recording mode needs to be configured in SETUP MENU and WJ-SX150 Administrator Console in advance.
• Detailed settings of GROUP is configurable only in WJ-SX150 Administrator Console.
20
• Motion Detector
When the multiplexer board detects motions in the image, the multiplexer board sends an alarm signal to the unit.
Then, the unit will send the alarm signal to the connected devices.
The areas can be divided in four segments, and the detection is conducted in each segment.
For example, this function can be applied to a time-lapse recording, which responds to the break-in at night.
Notes:
• The motion detector area needs to be configured in SETUP MENU in advance.
• The range of the motion detector is also configurable in the WJ-SX150 Administrator Console.
● Digital Disk Recorder WJ-HD100 Series/Time-lapse VCR
Fi
re
The multiplexed recording and playback of all the camera images connected to the unit are possible.
Each camera's image and camera ID are recorded.
The camera ID can search and play back the desired camera's image.
The digital disk recorder (WJ-HD100 Series) connected to the unit and time-lapse VCR have the following functions.
The operations are conducted with their buttons or the system controller or the PC.
The setup of the recording device
The start of the playback
The stop of the playback
The playback of the recorded images (the multiscreen display, still spot picture or still multiscreen picture, zoom spot picture)
• The search of the recorded image (the search by the camera ID, or the recorded time and date)
• Forward or backward search
• Forward of backward field advance
• Fast-forward
• Rewind
• Index
Refer to each device's operating instructions for details.
ec
ur
it
y&
•
•
•
•
In
te
llig
en
tS
Notes:
• When recording on the WJ-HD100 Series or time-lapse VCR, an optional Multiplexer board needs to be installed in this
unit.
• Only Panasonic time-lapse VCRs supporting RS232C are operable.
21
NOTIFICATION ABOUT PS·DATA CONTROLLER OPERATION
In the factory default setting, you can control the unit, if you connect a PS·Data system controller to the DATA 4 port. For example, if you connect a PS·Data unit supporting network connections (refer to p. 43), remote-control of the unit and the PS·Data
units will be available with a system controller or PC.
In
te
llig
en
tS
ec
ur
it
y&
Fi
re
When you use a PS·Data system controller, take notice the following:
• The administer authorization and log-in/log-out procedure differs from the unit. They are conformed to the system controller. Refer to the system controller's operating instructions.
• Use the PS·Data template supplied with the system controller, as the operating procedures differ from those of the terminal
mode. (Refer to pp. 107 to 113.)
• When connecting a recorder to the unit, you may have to configure the settings of the unit and recorder, depending on the
recorder's available functions and connections. (Refer to pp. 41 to 45.)
22
Fi
re
In
te
llig
en
tS
ec
ur
it
y&
DETAILED PRODUCT
DESCRIPTION
23
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
■ WJ-SX150 Matrix Switcher
● Front View
q
Fi
re
OPERATE
e
RESET
r
UNIT
MODE
ur
it
w
Matrix Switcher WJ-SX
y&
OPERATE LED WILL BLINK
IF COOLING FAN MALFUNCTIONS
78
ON
23
901
456
en
tS
ec
1 2 3 4
llig
q Operation indicator (OPERATE)
Lights up when the power of the unit is turned on.
In
te
Note: The indicator will blink to indicate rising temperature in the matrix switcher.
When the indicator blinks, turn the power off and
refer servicing to qualified service personnel.
r Mode selector (MODE)
Selects the unit's operation mode.
Normally, set all switches to OFF (NORMAL mode) as
shown in the figure.
w Reset button (RESET)
Resets and restarts the unit.
Note: The system configuration is not reset.
MODE SW SETUP
ON
1 2 3 4
ON
NORMAL
1 2 3 4
SX150
SOFTWARE UPLOAD
1 2 3 4
MULTIPLEXER
SOFTWARE UPLOAD
ON
e Unit number selector (UNIT)
This selector is reserved for future use.
Normally, set this switch to "1".
SX150 SOFTWARE UPLOAD:
Set the switches to this position when you update
the firmware of the unit. (Refer to the operating
instructions of the multiplexer board.)
MULTIPLEXER SOFTWARE UPLOAD:
This mode is reserved for future use.
24
● Rear View
u
o !0 !1
i
ALARM
DATA HDR DATA 4
SERIAL
DATA 3 DATA 2
DATA 1
!2 !3!4 !5 !6
LINE
2 SELECT 4
TERM
OFF
ON
PS•DATA
16
y
IN
t
OUT
15
14
13
12
11
10
EXT IN
(PLAY IN)
CAMERA
SW IN
RS485(CAMERA)
RS485(CAMERA)
9
8
7
6
5
EXT OUT
(REC OUT)
4
3
4
MONITOR OUT
3
2
!7
1
!8
SIGNAL GND
POWER
2
1
AC IN
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CAMERA
Fi
re
!9
!1 RS-485 Camera port
Connects to an RS-485 camera.
Daisy chain connection is also available.
t Camera Output connectors (CAMERA OUT 1–16)
The video signal connected to the CAMERA IN connector is supplied at these connectors.
When the power of the matrix switcher is turned off, no
signal is supplied at these connectors.
y&
ur
it
!3 Camera Switching Input connector (CAMERA SW IN)
The camera switching pulse from the time lapse VCR is
supplied to this connector.
The camera switching interval (Sequential Dwell Time)
can be synchronized with the time lapse mode set in
the associated time lapse VCR.
tS
ec
y Camera Input connectors (CAMERA IN 1-16)
Connect to cameras or camera site accessories.
These connectors accept either a composite color or
B/W video signal from a camera.
In addition, the VD2 signal to synchronize the vertical
timing of the cameras, and data to control camera site
devices are multiplexed at these connectors.
!2 Line selector (LINE SELECT 2/4)
Lets you select either full duplex (4 lines) or half duplex
(2 lines) for RS-485 cameras.
llig
en
u Termination selector (TERM ON/OFF)
When you connect a PS·Data system controller to the
DATA 4 port, this selector turns the unit's termination
switch to ON/OFF.
The factory default setting is ON.
te
Note: When you connect a terminal-mode system controller to the DATA 4 port, set this selector to ON.
!5 External Input connector (EXT IN/PLAY IN)
A playback or live images from the recorder are supplied to this connector.
!6 Monitor Output connectors (MONITOR OUT 1/2/3/4)
Connect to monitors.
The video output signals are supplied to the monitors at
these connectors.
o Data ports (DATA 1/2/3/4/DATA HDR)
• DATA 1 to 4 connect to the system controller.
DATA 1 to 3 can connect to RS-485 cameras with the
configuration in WJ-SX150 Administrator Console.
(Refer to p. 81.) DATA 4 can connect to the system
controller via the PS·Data protocol.
• DATA HDR connects to a recorder.
!7 Power switch (POWER)
Turns the power of the matrix switcher on and off.
In
i Alarm port (ALARM)
Connects to alarm sensors.
Accepts the alarm input from the associated alarm sensors.
!0 Serial port (SERIAL)
Connects to a PC for the system configuration through
WJ-SX150 Administrator Console.
25
!4 External Output connector (EXT OUT/REC OUT)
The recording signal for the recorder is provided via
this connector.
!8 AC Inlet socket (AC IN)
To use the unit, plug the power cord (supplied as a
standard accessory) into this socket and connect it to
an AC outlet.
!9 Blank panel
When the Multiplexer board installed in the unit, remove
this panel and then attach the cooling fan inside the
unit. (Refer to the Multiplexer board’s operating instructions.)
Note: Fan unit needs replacement after around 30 000
hours of operation.
■ WV-CU360C System Controller (TERMINAL MODE)
A template, on which “For Matrix Switcher (WJ-SX150)” is written, is provided with System Controller WV-CU360C. When using
the template, place it on the surface of the controller.
In these operating instructions, this template's illustrations are used for descriptions.
#8
#9
$0
@2
OPERATE
LINK
ALARM
@3 @4 @5
MONITOR
CAMERA
@6
@7
BUSY
PROHIBITED
System Controller WV-CU
360C
For Matrix Switcher (WJ-SX150)
F1
ACK
IRIS
RESET
CLOSE
CAM SETUP
SUSPEND
ALL RESET
F2
GROUP SEQ
TOUR SEQ
T&D
CAM ID
EVENT
STILL
AUX1 OFF
AUX1 ON
MON STATUS
ALL
OPEN
CALL
PRESET
$4
PREV
NEXT
STEP
RECORDER
PAUSE
STOP
FAR
Fi
re
NEAR
REW/FF
INDEX
UP
AUTO IRIS
FOCUS
PROGRAM
PRESET
AUTO FOCUS
AUTO PAN
ZOOM
L
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
WIDE
CAM FUNC
R
TELE
REC
DOWN
PLAY
PAUSE
DEF OFF
MON (ESC)
OSD
SETUP
SEQUENCE
SHIFT
CAM (SET)
MON LOCK
MULTI SCREEN SEL
#7
#6
%2 $8 %1 $7 %0
● Front View
CLEAR
LOG OUT
WIPER
#5
tS
@0 Operation indicator (OPERATE)
Lights up when the controller's power is turned on.
DEF ON
y&
STOP
ur
it
$6
$5
$9
@1
#4 #3 #2 #1 #0 @9
@8
ec
$1
$3
$2
@0
llig
en
@1 Link indicator (LINK)
Lights up when communication is established with the
matrix switcher.
te
@2 Alarm indicator (ALARM)
Lights up when an alarm condition exists.
In
@3 Monitor indicator (MONITOR)
Lights up when the monitor number appears on the
LED display.
@4 LED Display
Displays the monitor number, camera number, numeric
entry and error status, etc.
@5 Camera indicator (CAMERA)
Lights up when the camera number appears on the
LED display.
@6 Busy indicator (BUSY)
Lights up when the higher-priority operator selects the
camera or monitor you are currently operating.
Operations from the system controller are disabled until
this indicator goes off.
@7 Prohibited indicator (PROHIBITED)
Blinks when an operator attempts to control a monitor
(or camera) that is already used by a higher-priority
operator or the operator has done the prohibited operation.
@8 Joystick
Use this joystick to manually operate cameras, camera
site accessories and a recorder, or to move the cursor
in SETUP MENU on the active monitor screen.
UP:
Up
DOWN: Down
L:
Left, rewind*, backward field advance*
R:
Right, fast-forward*, forward field advance*
*Available after pressing the RECORDER button while
connecting to a recorder.
@9 Iris buttons (IRIS CLOSE/OPEN)
Close or open the lens iris of cameras equipped with
the specified lens.
Press the CLOSE and OPEN buttons simultaneously.
The lens iris is reset to the factory default setting.
26
#0 Focus buttons (FOCUS NEAR/FAR)
Adjust the lens focus of cameras equipped with the
specified lens.
Press the NEAR and FAR buttons simultaneously. The
lens focus is adjusted automatically, if the specified
auto focus camera is equipped.
• In the recorder mode, electronic zooming and multiscreen sequence, etc. are available when pressed in
combination with the SHIFT button.
#7 Monitor (Escape) button [MON (ESC)/MON LOCK]
MON: Press this button to select a monitor.
To select a monitor, press the corresponding
numeric buttons, followed by the MON (ESC) button.
ESC: Press this button to escape from the currently
highlighted selection and return to the previous
page of SETUP MENU.
MON LOCK: To prevent other operators from controlling the monitor, press this button while holding
down the SHIFT button. To release the lock, press
this button while holding down the SHIFT button
again. (Refer to p. 90.)
#1 Zoom buttons (ZOOM WIDE/TELE)
Press these buttons to zoom the lenses equipped with
the specified cameras.
Press the WIDE and TELE buttons simultaneously during the recorder mode. The recording is started.
y&
#9 Alarm Acknowledge button (ACK/SUSPEND)
ACK: Acknowledges an activated alarm.
To select the alarm monitor, press the ALARM button.
To select the desired alarm action number, press
the numeric buttons, then press this ACK button.
"ACK" will appear on the monitor.
To reset the alarm, press the RESET button after
acknowledging the alarm. "ACK" will go out.
SUSPEND: To suspend an activated alarm, press this
button while holding down the SHIFT button. "ALM
SUSPENDED" will appear on the monitor. To cancel
the suspension, press this button while holding
down the SHIFT button again.
en
tS
ec
#4 Clear button (CLEAR/LOG OUT)
Use this button to clear numeric input on the LED display, or exit from the ALARM HISTORY table (p. 101),
the VIDEO LOSS HISTORY table (p. 101), or the
SYSTEM STATUS table (p. 100).
To logout of the system, press this button while holding
down the SHIFT button.
#8 Alarm Reset button (RESET/ALL RESET)
RESET: To reset an alarm activated in the currently
active monitor, press this RESET button.
ALL RESET: To cancel all activated alarms at a time,
press this button while holding down the SHIFT button.
ur
it
#3 Auto Pan button (AUTO PAN/CAM FUNC)
Activates the auto panning function of cameras
equipped with this feature.
To execute camera functions, press this button in combination with the numeric buttons.(The specified cameras support this function.)
Fi
re
#2 Call Preset button (CALL PRESET/PROGRAM
PRESET)
To call the selected camera's preset position, press this
button in combination with the numeric buttons. (The
specified cameras support this function.)
To program a preset position, press the corresponding
numeric button(s), and then press this button while
holding down the SHIFT button.
In
te
llig
#5 Camera (Set) button [CAM (SET)/WIPER]
CAM: To select a camera, press the corresponding
numeric button, followed by this button.
SET: To enter numeric input, such as operator ID and
password, press this button in combination with the
numeric buttons.
Also use this button to execute the currently highlighted selection and go into a submenu of SETUP
MENU.
WIPER: To turn on the housing wiper of the camera,
press this button while holding down the SHIFT button.
#6 Numeric buttons
Press these buttons to enter numbers into the system
such as the camera and monitor number, sequence
number, preset position, etc.
• In combination with the OSD button, parameter
selection in OSD (On-screen Display) operation of
the monitor status or research in a history table
become available.
• In combination with the SHIFT button, AUX and
Defroster are available.
27
$0 Function 1 button (F1/CAM SETUP)
Press this button while holding down the SHIFT button
to open the camera's SETUP MENU on the active monitor.
The function as the F1 button is reserved for future use.
$1 Tour Sequence button (TOUR SEQ)
Press this button, in combination with the numeric buttons, to run a tour sequence on the active monitor.
$2 Group Sequence button (GROUP SEQ)
Press this button to select a group sequence.
To select a group, press the corresponding numeric
buttons, followed by the GROUP SEQ button.
$3 Function 2 button (F2/INDEX)
Displays date and time entry form during the recorder
mode.
%2 Setup button (SETUP)
To display the unit's SETUP MENU, press this button
while holding down the SHIFT button.
* The playback of the recorded images is possible when
a recorder is connected.
$4 Next button (NEXT)
Moves a tour sequence one step forward from the step
previously paused on the active monitor.
Also selects a camera. If the active monitor is in the
spot mode, press NEXT while holding down the CAM
(SET) button, to replace the currently selected camera
with the next higher-numbered camera.
During the recorder mode, this button moves the playback image one step forward.
Fi
re
$5 Previous button (PREV)
Moves a tour sequence one step backward from the
step previously paused on the active monitor.
Also selects a camera. If the active monitor is in spot
mode, press PREV while holding down the CAM (SET)
button, to replace the currently selected camera with
the next lower-numbered camera.
During the recorder mode, this button moves the playback image one step forward.
en
$8 Play button (PLAY)
Starts the playback of the recorded images*.
ur
it
tS
ec
$7 Pause button (PAUSE)
Pauses a tour sequence, and the playback of the
recorded images* that is being run on the active monitor.
Also restarts the sequence from the next step forward,
or the playback of the recorded images*.
y&
$6 Recorder button (RECORDER)
To enter the recorder mode, press this button. (Refer to
p. 116.)
Note: Only one operator can enter the recorder mode
at one time.
te
llig
$9 Stop button (STOP)
Ends a tour sequence, or stops the playback of the
recorded images* that is being run on the active monitor.
In
%0 Shift button (SHIFT)
To activate the alternate function of each button, press
this button, in combination with buttons associated with
special functions.
%1 On-screen Display button (OSD)
In combination with the numeric buttons, this button
toggles the currently selected display items on the
active monitor.
1: Clock display (T&D)
2: Camera title display (CAM ID)
3: Event display (EVENT)
4: Monitor status display (MON STATUS)
5: All displays (ALL)
7: ALARM HISTORY table (ALM H)
8: VIDEO LOSS STATUS table (VLD H)
9: SYSTEM STATUS table (SYS S)
28
■ WV-CU360CJ System Controller (TERMINAL MODE)
A template, on which “For Matrix Switcher (WJ-SX150)” is written, is provided with System Controller WV-CU360CJ. When
using the template, place it on the surface of the controller.
&3
&4
&5
%5
OPERATE
LINK
ALARM
%6 %7 %8
MONITOR
CAMERA
%9
^0
^1
BUSY
PROHIBITED
System Controller WV-CU
360CJ
For Matrix Switcher (WJ-SX150)
F1
ACK
IRIS
RESET
CLOSE
SUSPEND
ALL RESET
F2
GROUP SEQ
TOUR SEQ
T&D
CAM ID
EVENT
STILL
AUX1 OFF
AUX1 ON
MON STATUS
ALL
OPEN
AUTO IRIS
FOCUS
CALL
PRESET
NEAR
&9
PREV
NEXT
STEP
RECORDER
PAUSE
STOP
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
FAR
PROGRAM
PRESET
AUTO FOCUS
AUTO PAN
ZOOM
WIDE
^2
TELE
y&
REW/FF
INDEX
Fi
re
CAM SETUP
CAM FUNC
REC
STOP
PLAY
PAUSE
SEQUENCE
DEF OFF
MON (ESC)
OSD
SETUP
SHIFT
MON LOCK
MULTI SCREEN SEL
&2
&1
CLEAR
WIPER
LOG OUT
&0
^9 ^8^7 ^6 ^5 ^4
^3
en
tS
*7 *3 *6 *2 *5
DEF ON
CAM (SET)
ur
it
*1
*0
*4
%4
ec
&6
&8
&7
%3
llig
%3 Operation indicator (OPERATE)
Lights up when the controller's power is turned on.
In
te
%4 Link indicator (LINK)
Lights up when communication is established with the
matrix switcher.
%5 Alarm indicator (ALARM)
Lights up when an alarm condition exists.
%6 Monitor indicator (MONITOR)
Lights up when the monitor number appears on the
LED display.
%7 LED Display
Displays the monitor number, camera number, numeric
entry and error status, etc.
%8 Camera indicator (CAMERA)
Lights up when the camera number appears on the
LED display.
29
%9 Busy indicator (BUSY)
Lights up when the higher-priority operator selects the
camera or monitor you are currently operating.
Operations from the system controller are disabled until
this indicator goes off.
^0 Prohibited indicator (PROHIBITED)
Blinks when an operator attempts to control a monitor
(or camera) that is already used by a higher-priority
operator or the operator has done the prohibited operation.
^1 Zoom wheel controller
This control is used for zooming cameras equipped
with the specific lens. Moving the control to the right will
zoom in the image. Moving the control to the left will
zoom out the image.
&0 Camera (Set) button [CAM (SET)/WIPER]
CAM: To select a camera, press the corresponding
numeric button, followed by this button.
SET: To enter numeric input, such as operator ID and
password, press this button in combination with the
numeric buttons.
Also use this button to execute the currently highlighted selection and go into a submenu of SETUP
MENU.
WIPER: To turn on the housing wiper of the camera,
press this button while holding down the SHIFT button.
^2 Joystick
Use this joystick to manually operate cameras, camera
site accessories and a recorder, or to move the cursor
in SETUP MENU on the active monitor screen.
}:
Up
{:
Down
[:
Left, rewind*, backward field advance*
]:
Right, fast-forward*, forward field advance*
*Available after pressing the RECORDER button while
connecting to a recorder.
^3 Top button
Pressing this button will automatically set the lens focus
of a specified camera.
&1 Numeric buttons
Press these buttons to enter numbers into the system
such as the camera and monitor number, sequence
number, preset position, etc.
• In combination with the OSD button, parameter
selection in OSD (On-screen Display) operation of
the monitor status or research in a history table
become available.
• In combination with the SHIFT button, AUX and
Defroster are available.
• In combination with the SHIFT button, electronic
zooming and multiscreen sequence, etc. are available.
y&
&2 Monitor (Escape) button [MON (ESC)/MON LOCK]
MON: Press this button to select a monitor.
To select a monitor, press the corresponding
numeric buttons, followed by the MON (ESC) button.
ESC: Press this button to escape from the currently
highlighted selection and return to the previous
page of SETUP MENU.
MON LOCK: To prevent other operators from controlling the monitor, press this button while holding
down the SHIFT button. To release the lock, press
this button while holding down the SHIFT button
again.
tS
ec
^6 Zoom buttons (ZOOM WIDE/TELE)
Press these buttons to zoom the lenses equipped with
the specified cameras.
Press the WIDE and TELE buttons simultaneously during the recorder mode. The recording is started.
ur
it
^5 Focus buttons (FOCUS NEAR/FAR)
Adjust the lens focus of cameras equipped with the
specified lens.
Press the NEAR and FAR buttons simultaneously. The
lens focus is adjusted automatically, if the specified
auto focus camera is equipped.
Fi
re
^4 Iris buttons (IRIS CLOSE/OPEN)
Close or open the lens iris of cameras equipped with
the specified lens.
Press the CLOSE and OPEN buttons simultaneously.
The lens iris is reset to the factory default setting.
In
te
llig
en
^7 Call Preset button (CALL PRESET/PROGRAM
PRESET)
To call the selected camera’s preset position, press this
button in combination with the numeric buttons. (The
specified cameras support this function.)
To program a preset position, press the corresponding
numeric button(s), and then press this button while
holding down the SHIFT button.
^8 Auto Pan button (AUTO PAN/CAM FUNC)
Activates the auto panning function of cameras
equipped with this feature.
To execute camera functions, press this button in combination with the numeric buttons. (The specified cameras support this function.)
^9 Clear button (CLEAR/LOG OUT)
Use this button to clear numeric input on the LED display, or exit from the ALARM HISTORY table, the VIDEO
LOSS HISTORY table, or the SYSTEM STATUS table.
To logout of the system, press this button while holding
down the SHIFT button.
30
&3 Alarm Reset button (RESET/ALL RESET)
RESET: To reset an alarm activated in the currently
active monitor, press this RESET button.
ALL RESET: To cancel all activated alarms at a time,
press this button while holding down the SHIFT button.
&4 Alarm Acknowledge button (ACK/SUSPEND)
ACK: Acknowledges an activated alarm.
To select the alarm monitor, press the ALARM button.
To select the desired alarm action number, press
the numeric buttons, then press this ACK button.
"ACK" will appear on the monitor.
To reset the alarm, press the RESET button after
acknowledging the alarm. "ACK" will go out.
*4 Stop button (STOP)
Ends a tour sequence, or stops the playback of the
recorded images* that is being run on the active monitor.
SUSPEND: To suspend an activated alarm, press this
button while holding down the SHIFT button. "ALM
SUSPENDED" will appear on the monitor. To cancel
the suspension, press this button while holding
down the SHIFT button again.
*5 Shift button (SHIFT)
To activate the alternate function of each button, press
this button, in combination with buttons associated with
special functions.
&5 Function 1 button (F1/CAM SETUP)
Press this button while holding down the SHIFT button
to open the camera's SETUP MENU on the active monitor.
The function as the F1 button is reserved for future use.
*6 On-screen Display button (OSD)
In combination with the numeric buttons, this button
toggles the currently selected display items on the
active monitor.
1: Clock display (T&D)
2: Camera title display (CAM ID)
3: Event display (EVENT)
4: Monitor status display (MON STATUS)
5: All displays (ALL)
7: ALARM HISTORY table (ALM H)
8: VIDEO LOSS STATUS table (VLD H)
9: SYSTEM STATUS table (SYS S)
&6 Tour Sequence button (TOUR SEQ)
Press this button, in combination with the numeric buttons, to run a tour sequence on the active monitor.
Fi
re
&7 Group Sequence button (GROUP SEQ)
Press this button to select a group sequence.
To select a group, press the corresponding numeric
buttons, followed by the GROUP SEQ button.
ur
it
*7 Setup button (SETUP)
To display the unit's SETUP MENU, press this button
while holding down the SHIFT button.
* The playback of the recorded images is possible when
a recorder is connected.
en
tS
ec
&9 Next button (NEXT)
Moves a tour sequence one step forward from the step
previously paused on the active monitor.
Also selects a camera. If the active monitor is in the
spot mode, press NEXT while holding down the CAM
(SET) button, to replace the currently selected camera
with the next higher-numbered camera.
During the recorder mode, this button moves the playback image one step forward.
y&
&8 Function 2 button (F2/INDEX)
Displays date and time entry form during the recorder
mode.
In
te
llig
*0 Previous button (PREV)
Moves a tour sequence one step backward from the
step previously paused on the active monitor.
Also selects a camera. If the active monitor is in spot
mode, press PREV while holding down the CAM (SET)
button, to replace the currently selected camera with
the next lower-numbered camera.
During the recorder mode, this button moves the playback image one step forward.
*1 Recorder button (RECORDER)
To enter the recorder mode, press this button.
Note: Only one operator can enter the recorder mode
at one time.
*2 Pause button (PAUSE)
Pauses a tour sequence, and the playback of the
recorded images* that is being run on the active monitor.
Also restarts the sequence from the next step forward,
or the playback of the recorded images*.
*3 Play button (PLAY)
Starts the playback of the recorded images*.
31
● Rear View
*9
*8
78
(2
456
RISQUE DE CHOCS ELECTROUES
NE PAS OUVRIR
(1
23
901
RISK OF ELECTRIC
SHOCK. DO NOT OPEN
(0
CONTROLLER No. MODE
DATA
DC 9V IN
(3
y&
Fi
re
DC 9V IN
(1 DC 9V Input jack (DC 9V IN)
Use this jack to plug the AC adapter supplied with the
system controller.
#1
456
78
23
901
4(0Data ports (DATA)
Exchange the control data with the matrix switcher via
RS-485 cable (supplied with the system controller).
ur
it
*8 Controller Number switch (CONTROLLER No.)
Selects a number for the system controller for identification in a system. Normally, set the switch to number 1.
ec
CONTROLLER No.
llig
en
tS
*9 Mode Selection switches (MODE)
The operation mode of the system controller is selected
with these switches.
When you use a terminal-mode system controller, set
the switches to the positions shown in the figure.
OFF
2
3
4
5
te
ON
1
6
7
8
In
MODE
Note: When you use a PS·Data system controller, refer
to the system controller's operating instructions.
32
(2 Clamp
Fastens the supplied AC adapter's power cord.
(3 AC adapter
Caution: Use only the supplied AC adapter to feed 9 V
DC to the system controller.
Note: Disconnect the plug from the controller before
setting the controller number switch or mode selection switch, and reconnect it when finished. The
new settings will take effect when the power is
turned on.
Fi
re
In
te
llig
en
tS
ec
ur
it
y&
INSTALLATIONS AND SYSTEM
CONNECTIONS
33
INSTALLATIONS
Notes:
• An optional cooling fan attached inside the unit is
subject to wear. It needs to be replaced periodically.
Keep the temperature in the rack below 45 °C
(113 °F) at any time.
• If the rack is subject to vibration, secure the rear of
the appliance to the rack by using additional mounting brackets (procured locally).
WARNING
The installations described in the figures should be
made by qualified service personnel or system
installers.
■ Mounting into the Rack
The matrix switcher can be mounted into the rack as
described.
1. Remove the four rubber feet by unwinding the four
screws on the bottom of the matrix switcher.
Fi
re
■ Installing the Multiplexer Board
ur
it
y&
To use WJ-HD100 Series or a time-lapse VCR as a
recorder, you need to install a multiplexer board inside the
matrix switcher. Refer to the multiplexer board’s operating
instructions for how to install.
ec
Remove 4 rubber feet
In
te
llig
en
tS
2. Place the rack mounting brackets on both sides of the
matrix switcher and tighten with the four supplied
screws (M4 X10).
3. Install the matrix switcher in the rack with the rack
mounting brackets secured with four screws (procured
locally).
34
SYSTEM CONNECTION EXAMPLES
■ Basic System Connection
This is an example of basic system connection.
Camera
3
Camera Camera
1
2
Camera
16
CAMERA IN 1 to 16
Fi
re
WJ-SX150
Matrix Switcher
ALARM IN 1 to 16
OPERATE
OPERATE LED WILL BLINK
IF COOLING FAN MALFUNCTIONS
Matrix Switcher WJ-SX
360C
System Controller WV-CU
For Matrix Switcher (WJ-SX150)
PS·Data/Terminal-mode
360C
System Controller WV-CU
For Matrix Switcher (WJ-SX150)
360C
System Controller WV-CU
For Matrix Switcher (WJ-SX150)
NEXT
360C
For Matrix Switcher (WJ-SX150)
NEXT
NEXT
ec
Max. 4 System Controllers
ur
it
System Controller WV-CU
NEXT
MONITOR OUT 1 to 4
y&
Terminal-mode
tS
Note: Before connecting a terminal-mode system controller to the DATA 4 port, configure the system through SETUP
MENU or WJ-SX150 Administrator Console.
■ System Expansion Connection
en
● Connection with Digital Disk Recorder WJ-HD500 Series
Camera
16
In
Camera Camera
1
2
te
Camera
3
llig
When connecting the camera output connectors to Digital Disk Recorder WJ-HD500 Series, the digital disk recorder can
record all the camera channels. More than one camera images can be displayed in multiscreen segments on the desired monitor.
CAMERA IN 1 to 16
ALARM IN 1 to 16
MONITOR OUT 1 to 4
Available for live or play-backed camera images
(GENLOCK OFF)
OPERATE
OPERATE LED WILL BLINK
IF COOLING FAN MALFUNCTIONS
Matrix Switcher WJ-SX
WJ-SX150 Matrix Switcher
REMOTO
LOCK
ALARM
1
2
3
Terminal-mode
REC STOP
4
GROUP
SELECT
STOP
PLAY/ PAUSE
REC
PS·Data/Terminal-mode
FS 16
SET
TIMER
ALARM
RESET
ALARM
SUSPEND
OPERATE
HDD
FULL
SPOT
MULTISCREEN
MULTISCREEN
SELECT
SEQUENCE
5
6
7
8
9
10
11
12
13
14
15
16
REC PREVIEW
INDEX
EL-ZOOM
ALARM SEARCH
System Controller WV-CU
REV
FWD
COPY
System Controller WV-CU
360C
System Controller WV-CU
For Matrix Switcher (WJ-SX150)
NEXT
360C
Digital Disk Recorder WJ-HD500 Series
System Controller WV-CU
For Matrix Switcher (WJ-SX150)
NEXT
DISPLAY
DAYLIGHT SAVINGS
Digital Disk
Recorder
WJ-HD
35
360C
For Matrix Switcher (WJ-SX150)
NEXT
SET UP
/ESC
A
Max. 4 System Controllers
360C
For Matrix Switcher (WJ-SX150)
NEXT
Notes:
• Before connecting a terminal-mode system controller to the DATA 4 port, configure the system through SETUP MENU or
WJ-SX150 Administrator Console.
• If an optional network board is installed inside the recorder and you are to control it from LAN (local area network) or the
Internet, refer to a service manual procurable in your area.
● Connection with Digital Disk Recorder WJ-HD100 Series or Time-lapse VCR
• With the multiplexer board, the recorded images of Camera 1 to 16 can be multiplexed to Digital Disk Recorder, WJHD100 Series or a time-lapse VCR.
Camera
3
Camera Camera
1
2
Camera
16
y&
Fi
re
Max. 16
Camera Inputs
OPERATE
Matrix Switcher WJ-SX
ur
it
OPERATE LED WILL BLINK
IF COOLING FAN MALFUNCTIONS
16 Alarm Inputs
Multiplexer Board
WJ-SXB151
ec
WJ-SX150 Matrix Switcher
360C
System Controller WV-CU
For Matrix Switcher (WJ-SX150)
System Controller WV-CU
For Matrix Switcher (WJ-SX150)
360C
For Matrix Switcher (WJ-SX150)
NEXT
NEXT
en
NEXT
360C
tS
Digital Disk Recorder WJ-HD100A or Time-Lapse VCR
System Controller WV-CU
llig
Max. 4 System Controllers
System Controller WV-CU
360C
For Matrix Switcher (WJ-SX150)
NEXT
4 Monitor Outputs
Available for surveillance or playback of the camera images
In
te
To use WJ-HD100 Series or a time-lapse VCR as a recorder, you need to install a multiplexer board inside the matrix
switcher.
36
CONNECTIONS
■ Connection with the Camera Sites
Connect non-multiplex type cameras to the CAMERA IN
connectors 1 to 16. For cameras equipped with RS-485
communication facilities, connect the RS-485 cable as follows.
Connect the data-multiplex type cameras (or camera site
equipment) to the CAMERA IN connectors 1 to 16 on the
matrix switcher's rear panel.
Notes:
• Make sure that the cable length is less than 900 m
(3 000 ft) between the camera site and the unit when
using RG-59/U, BELDEN 9259 or equivalent cables.
• If you use locally procuring cables, it is important to use
only a data-grade cable, which is suitable for RS-485
communication (shielded 2-wire twisted cable).
• When the cable length is extended, cable compensation is available. (Refer to pp. 60 and 78.)
Check the camera addresses when using RS-485 cameras.
Operations from the system controller will be invalid if the
camera addresses are set improperly.
tS
ec
ur
it
y&
Fi
re
• Use addresses from 1 to 16 for individual cameras.
• Do not set the same address for more than one camera
in an RS-485 chain.
• Before connecting the RS-485 camera(s) to DATA 1, 2
and/or 3, configure the system through WJ-SX150
Administrator Console.
llig
en
AUX
Alarm
IN
In
te
DATA 3 DATA 2
16
10
16
10
DATA 1
RS485(CAMERA)
LINE
2 SELECT 4
RS485(CAMERA)
9
8
7
6
5
4
3
2
1
9
8
7
6
5
4
3
2
1
OUT
CAMERA
WJ-SX150 Matrix Switcher
37
■ Connections for RS-485 Type Camera
(A)
(B)
GND
There are two options to connect the camera with the matrix
switcher, depending on the distance between them.
One is "Home Run" wiring and the other is daisy chain
wiring. "Home Run" wiring has the transmission stability with
less transmission loss, and daisy chain wiring has connection flexibility with less data ports occupied. For data-multiplex type cameras, 900 meters (3 000 ft) is the limit to use
coaxial cable such as RG-59/U, BELDEN 9259 or equivalent.
OFF
ON
WV-CPR450 and others (For the
Termination Switch positions, refer
to the oprating instractions of the
camera.)
Set it to
position 2.
DATA HDR DATA 4
Note: If more distance is required, use cameras and
matrix switcher with RS-485 communication feature.
Remote control becomes possible.
DATA 3 DATA 2
TERM
OFF
ON
PS•DATA
DATA 1
RS485(CAMERA)
LINE
2 SELECT 4
RS485(CAMERA)
WJ-SX150
Fi
re
● "Home Run" Wiring
1. Connect with a RS-485 camera in "Home Run" wiring as
shown in the figure.
2. Set the LINE SELECT switch to 2 or 4.
y&
1. Draw up a plan for connection between the cameras
and the input channels of the matrix switcher, and the
assignment of unit addresses to cameras.
ur
it
2. Set the LINE SELECT switch to 2. Also, set the connected device's switch if required.
3. Connect one end of the cable to RS-485 (CAMERA),
and the other end to the first camera in the chain, as
shown in the figure. Repeat this procedure for all cameras.
llig
en
tS
ec
Notes:
• Before connecting RS-485 cameras to DATA1 to 3, data
port setting through WJ-SX150 Administrator Console is
necessary. (Refer to p. 81 Data Port.)
• Recommended for RS-485 communication is AWG#22
or thicker one. The cable should be shielded, two-wire,
twisted pair, and with low impedance.
• Set the LINE SELECT switch to 4 when programming
preset position of WV-CSR600/650 Series camera is
connected to the unit.
● Daisy Chain Wiring
In
te
RS-485 type camera
DATA HDR DATA 4
DATA 3 DATA 2
TERM
OFF
ON
PS•DATA
DATA 1
Set it to
position 4.
RS485(CAMERA)
LINE
2 SELECT 4
RS485(CAMERA)
WJ-SX150
RS485 Port
Matrix switcher's rear panel
RB
RA
None
TA
TB
38
GND
RB
RA
TB
TA
4. Set the termination switches of the cameras at the chain
ends to ON. Camera's termination switches must be set
to OFF except the ones at the chain ends.
Notes:
• Set the same number for the camera's unit address as
and CAMERA IN.
• Check the settings of the camera addresses when
using RS-485 cameras. Operations from the system
controller will be invalid if the camera addresses are set
improperly.
• Do not use addresses other than 1 to 16 for individual
cameras (More than 17 cameras are not allowed).
• Do not set the same address for more than one camera
in an RS-485 chain.
• Termination is the key to data transmission and reception in the chain. While the other switches are set to
OFF, only the switches at the chain ends must be set to
ON.
• The termination of this unit's RS-485 camera port is
always set to ON. Connect the unit at the end of the
daisy chain.
• The more equipment there is in the chain, the slower
the response may be.
The switch on a daisychain-connected unit
other than the
extremities must be set
to OFF.
(A)
(B)
GND
OFF
■ Connection with the Monitors
The switch on the end
unit should be set to
ON.
(A)
(B)
GND
ON
OFF
Connect the monitors to the MONITOR OUT connectors at
the unit's rear panel with the coaxial cable.
The connectors MONITOR OUT 1 to 4 are associated to
ON
Martix Switcher
3
WV-CPR450 and others
(For the termination
switch positions, refer
to the operating
instruction of the
corresponding unit.)
DATA 3 DATA 2
PS•DATA
LINE
2 SELECT 4
Set it to 2 or 4
(the same as
the connected
equipment).
RS485(CAMERA)
Monitor 3
WJ-SX150
y&
Unit address 1
ec
ur
it
Unit address 2
en
tS
Set the same
number for the
camera's unit
address as and
CAMERA IN.
DATA 1
10
16
10
9
8
7
9
8
7
4
3
2
1
te
RS485(CAMERA)
16
6
3
2
1
IN
OUT
6
5
5
In
CAMERA
llig
DATA 3 DATA 2
4
WJ-SX150 Matrix Switcher
39
Monitor 4
Monitor 2
Monitor 1
Monitor 1 to 4. When you control the monitors from a PS·
Data controller, the connectors MONITOR OUT are associated to Unit 1 to 4.
Auto termination works inside the matrix switcher.
Unit address 4 Unit address 3
2
RS485(CAMERA)
DATA 1
Fi
re
DATA HDR DATA 4
TERM
OFF
ON
4
MONITOR OUT
1
■ Connection with the System
Controllers
■ Connection with the Alarm Sensors
Connect the sensor switches to the unit's alarm port, as
shown in the example.
Connect the system controller to the DATA 1 to 4 port at the
unit's rear panel with the modular cable.
Recover
Input
Alarm
Sensor 1
13
DATA HDR DATA 4
DATA 3 DATA 2
DATA 1
LINE
2 SELECT 4
TERM
OFF
ON
PS•DATA
1
RS485(CAMERA)
ALARM
RS485(CAMERA)
25
WJ-SX150
360C
System Controller WV-CU
For Matrix Switcher (WJ-SX150)
360C
For Matrix Switcher (WJ-SX150)
NEXT
System controller
System controller
ur
it
DATA1 to DATA4 Port
Matrix switcher's rear panel
DATA 1 to 4
tS
GND
RB
RA
llig
en
TA
TB
ec
RB
RA
TB
TA
GND
In
te
Notes:
• Up to four system controllers are connectable.
• Connect them in home run.
• In the factory default setting, the DATA 4 port is a
PS·Data terminal. To connect a terminal-mode system
controller to this port, you need to change the data port
setting
through
SETUP MENU
or
WJ-SX150
Administrator Console. (Refer to pp. 60 or 81.)
40
Alarm Input 1
Alarm Input 3
Alarm Input 5
Alarm Input 7
Alarm Input 9
Alarm Input 11
Alarm Input 13
Alarm Input 15
GND
Alarm Output 1
Alarm Output 3
GND
Recover Input
y&
NEXT
1
2
3
4
5
6
7
8
9
10
11
12
13
Designation
Fi
re
Pin No.
System Controller WV-CU
14
Alarm
Sensor 2
Pin No.
14
15
16
17
18
19
20
21
22
23
24
25
Designation
Alarm Input 2
Alarm Input 4
Alarm Input 6
Alarm Input 8
Alarm Input 10
Alarm Input 12
Alarm Input 14
Alarm Input 16
GND
Alarm Output 2
Alarm Output 4
GND
Notes:
• Alarm inputs that are simultaneous or with very short
intervals will be ignored.
Allow for at least 100 ms interval from one alarm input to
the next.
• Confirm the alarm sensor type (N.O. or N.C.) and configure the system through SETUP MENU (OSD) or WJSX150 Administrator Console.
The factory setting is N.O.
N.O.: Normally Open alarm contact
N.C.: Normally Closed alarm contact
• The alarm pin assigned to the time adjust (TIME) terminal cannot be used as an alarm input terminal.
■ Connection with the Alarm Output
■ Connection with Digital Disk
Recorder WJ-HD500 Series
Pins #10, 11, 23 and 24 (open collector) turns to 0 V while
the alarm is activated. These terminals can drive external
warning devices such as a buzzer or lamp of up to 100 mA,
16 V DC. If the rating exceeds 100 mA, 16 V DC use a relay
as shown in Example 2.
Alarm signals are output from the terminals until the reset.
Note: Refer to a service manual procurable in your area, for
details on the connection with a recorder (after the network board installation) to operate via LAN or the
Internet.
Example 1: Direct drive connection
● To Confirm the Images from a Recorder
Connected to the Unit
The following is the description of the connection between a
recorder and this unit to confirm the images from the
recorder.
Fi
re
1. Set the unit address of the recorder to 1. Then, confirm
that the recorder’s CAMERA GENLOCK is set to OFF in
its SETUP MENU. (Refer to the recorder's operating
instructions.)
Buzzer
2. Connect the unit’s CAM OUT 1 to 16 connectors to the
recorder’s VIDEO IN 1 to 16 connectors with a coaxial
cable.
y&
Example 2: Connection of devices exceeding drive
NC
ur
it
3. Connect the unit’s EXT IN connector to the recorder’s
MULTI SCREEN OUT connector with a coaxial cable.
4. Connect the unit’s DATA HDR connector to the
recorder’s DATA port with a modular cable.
(The control data and alarm signal will be output from
the unit to the recorder.)
ec
NO
tS
To Buzzer
C
Relay
en
+12V
5. After the connection, set the unit’s EXT IN to GENLOCK
ON through SETUP MENU or WJ-SX150 Administrator
Console (Refer to pp. 60 or 66).
GND
Monitor
WJ-SX150 Matrix Switcher
In
te
llig
NC: Normally Closed Contact
NO: Normally Open Contact
C: Common
ALARM
SERIAL
DATA 3 DATA 2
DATA HDR DATA 4
PS•DATA
15
14
13
12
11
10
16
15
14
13
12
11
10
EXT IN
(PLAY IN)
CAMERA
SW IN
RS485(CAMERA)
DATA 1
LINE
2 SELECT 4
TERM
OFF
ON
16
MONITOR
OUT
EXT IN
RS485(CAMERA)
9
8
7
6
5
9
8
7
6
5
3
1
4
MONITOR OUT
EXT OUT
(REC OUT)
4
2
3
2
1
3
2
1
IN
OUT
4
CAMERA
DATA HDR
MULTI SCREEN
OUT
IN
EXT STORAGE
GEN-LOCK OUT
COPY
SPOT
OUT
OUT
MULTI SCREEN OUT AUDIO
CONTROL
ALARM
SIGNAL GND
REMOTE(WV-CU50)
DATA
10/100BASE-T
SERIAL
MODE
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
IN
OUT
VIDEO
WJ-HD500 Series Digital Disk Recorder
41
● To Record the Camera Images in Maximum
Recording Rate
Notes:
• You cannot record the camera images in maximum
recording rate through this connection. Refer to the next
connection example in this page.
• The recorder will not operate if its unit address is set to
other than 1.
The following is the description of the connection between a
recorder and this unit for the maximum-rate recording.
1. Set the unit address of the recorder to 1. Then, set the
recorder’s CAMERA GENLOCK to ON in its SETUP
MENU. (Refer to the recorder's operating instructions.)
2. Connect the unit’s CAM OUT 1 to 16 connectors to the
recorder’s VIDEO IN 1 to 16 connectors with a coaxial
cable.
3. Connect the unit’s EXT IN connector to the recorder’s
GENLOCK OUT connector with a coaxial cable.
Fi
re
4. Connect the unit’s DATA HDR connector to the
recorder’s DATA port with a modular cable.
(The control data and alarm signal will be output from
the unit to the recorder.)
y&
5. After the connection, set the unit’s EXT IN to GENLOCK
ON through SETUP MENU or WJ-SX150 Administrator
Console (Refer to pp. 60 or 66).
EXT IN
WJ-SX150 Matrix Switcher
te
llig
en
tS
ec
ur
it
Notes:
• You need WJ-HD500A or a newer model for the maximum-rate recording.
• The playback, multiscreen output or live images from the
recorder are not displayed on Monitor 1 to 4. To confirm
the images, you need to connect another monitor with
the recorder.
• The recorder will not operate if its unit address is set to
other than 1.
• Make sure the DATA HDR port's unit address is set to 1
through WJ-SX150 Administrator Console. (Refer to p.
66.) If another number is selected, you cannot control
the recorder.
ALARM
SERIAL
DATA 3 DATA 2
In
DATA HDR DATA 4
PS•DATA
16
15
14
13
12
11
10
16
15
14
13
12
11
10
EXT IN
(PLAY IN)
CAMERA
SW IN
RS485(CAMERA)
DATA 1
LINE
2 SELECT 4
TERM
OFF
ON
RS485(CAMERA)
9
8
7
6
5
9
8
7
6
5
3
1
4
MONITOR OUT
EXT OUT
(REC OUT)
4
2
3
2
1
3
2
1
IN
OUT
4
CAMERA
DATA HDR
DATA
MULTI
SCREEN
OUT
IN
EXT STORAGE
GEN-LOCK OUT
COPY
SPOT
OUT
CONTROL
ALARM
SIGNAL GND
REMOTE(WV-CU50)
DATA
OUT
MULTI SCREEN OUT AUDIO
10/100BASE-T
SERIAL
MODE
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
IN
OUT
VIDEO
WJ-HD500A or a newer model
Monitor
42
GENLOCK
OUT
● To Control a Recorder via the Network
Monitor
The following is the description of the connection between
a recorder and this unit to control the recorder via the network.
1. Set the recorder's unit address to a number 5 or larger .
(Refer to the recorder's operating instructions.)
WJ-SX150 Matrix Switcher
ALARM
2. Connect the unit’s CAM OUT 1 to 16 connectors to the
recorder’s VIDEO IN 1 to 16 connectors with a coaxial
cable.
SERIAL
DATA 3 DATA 2
DATA HDR DATA 4
PS•DATA
15
14
13
12
11
10
16
15
14
13
12
11
10
EXT IN
(PLAY IN)
CAMERA
SW IN
RS485(CAMERA)
DATA 1
LINE
2 SELECT 4
TERM
OFF
ON
16
MONITOR
OUT
EXT IN
RS485(CAMERA)
9
8
7
6
5
9
8
7
6
5
3
1
4
MONITOR OUT
EXT OUT
(REC OUT)
4
2
3
2
1
3
2
1
IN
OUT
4
CAMERA
3. Connect the unit’s DATA HDR and DATA4 connectors
to the recorder’s DATA port with a daisy chain connection cable kit (WV-CA48/10K).
(The control data and alarm signal will be output from
the unit to the recorder.)
MULTI SCREEN
OUT
IN
SPOT
OUT
16
15
IN
ALARM
SIGNAL GND
REMOTE(WV-CU50)
DATA
10/100BASE-T
SERIAL
10/100 BASE-T
MODE
12
11
10
9
8
7
6
5
4
3
2
1
12
11
10
9
8
7
6
5
4
3
2
1
OUT
16
15
14
13
VIDEO
ur
it
Digital Disk Recorder*
LAN cable
HUB/Router
ec
tS
en
llig
te
In
13
GEN-LOCK OUT
COPY
CONTROL
14
y&
5. Through a browser, set the unit address of an optional
network board (WJ-HDB502) to a number other than 1.
(Refer to WJ-HDB502 Operating Instructions.)
DATA
EXT STORAGE
OUT
MULTI SCREEN OUT AUDIO
43
Fi
re
Daisy Chain Connection Kit
(WV-CA48/10K)
4. Select the recorder's new unit address, which is set in
step 1, for DATA HDR in the Data Port window. (Refer to
p. 66.)
6. Refer to p. 39, p. 41 and p. 42 for MONITOR OUT connection, MULTI SCREEN OUT connection, and EXT IN
connection.
DATA4
(PS·Data)
DATA HDR
LAN**
* WJ-HD500A or Newer Models with Network Board (WJ-HDB502)
** LAN : Local Area Network
Notes:
• You will need WJ-HD500A or a newer model, in which
an optional network board (WJ-HDB502) is installed.
• Select the PS·Data protocol for the DATA 4 setting.
(Refer to p. 61 DATA 4/PSD PORT SELECT or p. 81
Data Port.) If the terminal mode is selected, you cannot
control the recorder.
• The recorder will not be operable if its unit address is
set to 1.
• If the recorder's unit address in step 1 and the DATA
HDR setting in step 4 are different, the recorder will not
be operable.
• In these connections, you cannot use a PS·Data system
controller.
43
■ Connection with Digital Disk Recorder WJ-HD100 Series
1. To record the camera images with Digital Disk Recorder WJ-HD100 Series, install an optional Multiplexer board in the
matrix switcher.
2. Connect the matrix switcher’s EXT OUT (REC OUT) to the digital disk recorder’s VIDEO IN with a coaxial cable.
3. Connect the matrix switcher’s EXT IN (PLAY IN) to the digital disk recorder’s MONITOR OUT (PLAY) with a coaxial cable.
4. Connect the matrix switcher’s DATA HDR to the digital disk recorder’s DATA with a modular cable.
5. Connect the matrix switcher’s CAMERA SW IN to the digital disk recorder’s CAMERA SW OUT with an RCA-pin cable.
6. Select “HD100” for 610 RECORDER CONTROL in SETUP MENU. (Refer to p. 60.)
7. Conform the parameter of 740 PSD PORT SPEED to the setting of the recorder.
The following parameters are fixed.
Data bit: 8 bits
Parity check: None
Stop bit: 1 bit
8 Conform the parameter of 620 RECORDER UNIT ADDRESS in SETUP MENU to the setting of the recorder. (Refer to the
recorder’s operating instructions for the unit address.)
WJ-SX150 MatrixSwitcher
ALARM
SERIAL
DATA 3 DATA 2
DATA HDR DATA 4
DATA 1
RS485(CAMERA)
LINE
2 SELECT 4
TERM
OFF
ON
EXT OUT
(REC OUT)
RS485(CAMERA)
Pin #24 (Alarm Out 4)
Pin #23 (Alarm Out 2)
AUDIO
CAMERA
SW OUT
RS-232C
DATA
MODE
4
MONITOR OUT
2
G
RECALL
OUT
RECOVER OUT
RESET IN
IN
G
ec
VIDEO MONITOR OUT
(PLAY)
G
OUT
ALARM SEARCH
STEP
REW/FF
STOP/SETUP
PLAY
REC
OUT
(EXT REC)
JOG-CLICK
JOG-LEFT
JOG-RIGHT
IN
tS
IN
1
ur
it
Pin #9 (GND)
3
y&
PS•DATA
EXT IN
(PLAY IN)
CAMERA
SW IN
OUT
IN
PLAY OUT
REC OUT
AUTO OFF OUT
DISK END OUT
OUT
IN
Pin #13
(Recover Input)
Fi
re
Pin #10 (Alarm Out 1)
Pin #11 (Alarm Out 3)
POWER
ON
SIGNAL GND
OFF
REMOTE
TIME
ADJUST
SERIES
RECORD
ALARM
llig
en
WJ-HD100 series Digital Disk Recorder
● DATA HDR Port
In
te
Note: After the connection, configure the system through SETUP MENU and WJ-SX150 Administrator Console.
DATA HDR Port
Matrix switcher's rear panel
DATA HDR
TB
TA
GND
RA
RB
44
GND
TB
TA
RB
RA
■ Connection with the Time-lapse VCR (Panasonic Models)
ec
Pin #10(Alarm out 1)
Pin #11(Alarm out 3)
ur
it
y&
Fi
re
1. Configure the parameters of the multiplexer functions in the Multiplexer Mode (refer to p. 82) window of WJ-SX150
Administrator Console.
Note: When VCR is selected in 610 RECORDER CONTROL in SETUP MENU (refer to p. 60), parameter configuration in the
Multiplexer Mode window is unavailable.
2. Select VCR for 610 RECORDER CONTROL in SETUP MENU. (Refer to p. 60.)
3. Conform the communication speed (COMM. SPEED) for 750 SERIAL PORT SPEED in SETUP MENU to that of the timelapse VCR. (Refer to p.61.)
The following parameters are fixed.
Data bit: 7 bits
Parity check: ODD
Stop bit: 1 bit
4. Connect the matrix switcher’s EXT OUT (REC OUT) to the time-lapse VCR’s VIDEO IN with the coaxial cable.
5. Connect the matrix switcher’s EXT IN (PLAY IN) to the time-lapse VCR’s VIDEO OUT with the coaxial cable.
6. Connect the matrix switcher’s SERIAL to that of the time-lapse VCR with a 9-pin D-sub cable.
7. Connect the matrix switcher’s CAMERA SW IN to the time-lapse VCR’s CAMERA SW OUT with an RCA-pin cable.
Notes:
• Only Panasonic time-lapse VCRs which support RS-232C are usable. (Refer to Cable Specifications on the next page
for details of cables.)
• Both of the time-lapse VCR and PC cannot be connected to the matrix switcher.
• When configuring the system through WJ-SX150 Administrator Console, pull out the time-lapse VCR’s cable and connect the PC’s cable to the serial port.
• To use the alarm recording function, connect the matrix switcher’s all alarm output terminals (Alarm Output 1 to 4) to
the time-lapse VCR’s ALARM IN.
• Be sure to activate auto-recovery for the VCR’s alarm reset function.
Pin #13
(Recover Input)
WJ-SX150 MatrixSwitcher
ALARM
DATA HDR DATA 4
SERIAL
DATA 3 DATA 2
DATA 1
tS
TERM
OFF
ON
PS•DATA
LINE
2 SELECT 4
EXT IN
(PLAY IN)
CAMERA
SW IN
3
4
MONITOR OUT
EXT OUT
(REC OUT)
RS485(CAMERA)
en
Pin #24(Alarm out 4)
Pin #23(Alarm out 2)
RS485(CAMERA)
Time Lapse VCR
VIDEO IN
VIDEO OUT
S-VIDEO
te
llig
Pin #9(GND)
AUDIO
CAMERA
SW OUT
In
GND
2
1
4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1
2
COM
3
ALARM
RESET IN
ALARM
RECOVER OUT
4
45
ALARM
IN
5
ALARM
OUT
9
WARNING
OUT
13
6 1 SHOT IN 10 HUMID OUT 14
7
COM
8
TAPE END
OUT
11 REC OUT
12
REC REVIEW
OUT
15
16
SERIES
REC IN
SERIES
REC OUT
TIME
ADJUST IN
TIME
ADJUST OUT
1
2
■ Cable Specifications
AG6730, AG6740
RT850
WJ-SX150
T/L VCR
WJ-SX150
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
20
22
Frame
Frame
RT850
1
2
3
4
5
6
7
8
9
Straight Cable
Fi
re
Shield
■ Connection with the Time-lapse VCR (Non-Panasonic Models)
y&
To record the camera images through a time-lapse VCR, install an optional Multiplexer board in the matrix switcher.
Select OFF for 610 RECORDER CONTROL in SETUP MENU.
Connect the matrix switcher’s EXT OUT (REC OUT) to the time-lapse VCR’s video input connector with the coaxial cable.
Connect the matrix switcher’s EXT IN (PLAY IN) to the time-lapse VCR’s video output connector with the coaxial cable.
ur
it
1.
2.
3.
4.
Pin #10(Alarm out 1)
Pin #11(Alarm out 3)
en
Pin #13
(Recover Input)
tS
ec
Notes:
• To use the alarm recording function, connect the matrix switcher’s all alarm output terminals (Alarm Output 1 to 4) to the
time-lapse VCR’s ALARM IN.
• Refer to p. 45 “Connection with the Time-lapse VCR (Panasonic Models) ” for the illustration.
• Be sure to set the VCR to automatically recover from alarm reset.
WJ-SX150 MatrixSwitcher
ALARM
DATA HDR DATA 4
SERIAL
DATA 3 DATA 2
DATA 1
llig
TERM
OFF
ON
Pin #24(Alarm out 4)
Pin #23(Alarm out 2)
PS•DATA
RS485(CAMERA)
LINE
2 SELECT 4
EXT IN
(PLAY IN)
CAMERA
SW IN
3
4
MONITOR OUT
EXT OUT
(REC OUT)
RS485(CAMERA)
In
te
Pin #9(GND)
Time Lapse VCR
VIDEO IN
VIDEO OUT
S-VIDEO
AUDIO
GND
CAMERA
SW OUT
2
1
4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1
2
COM
3
ALARM
RESET IN
ALARM
RECOVER OUT
4
46
ALARM
IN
5
ALARM
OUT
9
WARNING
OUT
13
6 1 SHOT IN 10 HUMID OUT 14
7
COM
8
TAPE END
OUT
11 REC OUT
12
REC REVIEW
OUT
15
16
SERIES
REC IN
SERIES
REC OUT
TIME
ADJUST IN
TIME
ADJUST OUT
1
2
■ Connection with the PC
■ Time Adjustment with an External
Equipment
1. Conform the communication speed (SERIAL PORT
SPEED) parameter in SETUP MENU to that of the PC.
2. Connect the matrix switcher's serial port to that of the
PC with the 9-pin D-sub cable.
D-sub9
or
D-sub25
The specified external devices can output the time adjusting signal to the matrix switcher.
This signal can adjust the time by up to ± 30 seconds every
hour.
To use this function, it is necessary to assign one of the
alarm input terminals (pin # 1 to 16) to the time adjusting
terminal.
SETUP MENU or WJ-SX150 Administrator Console can
assign the signal.
D-sub9
SERIAL
Personal Computer
● Master Clock Connection Example for Time
Adjustment
Matrix Switcher
Connect the matrix switcher's time adjusting terminal to
those of the master clock with the twisted pair cable.
The figure below shows the case in which Alarm Input 16 is
assigned as the time adjusting terminal.
WJ-SX150
1
1
2
2
3
3
4
4
5
5
llig
7
7
y&
Matrix Switcher
ALARM
Pin #22
GND
tS
en
6
6
Pin #21
12
9
3
6
8
8
Frame
Frame
In
te
Shield
47
ec
PC
Note: A master clock with N.O. (Normally Open alarm contact)-type output is connectable.
ur
it
● Cable Specifications
Fi
re
Notes:
• The following parameters are fixed.
Data bit: 8 bits
Parity check: none
Stop bit: 1 bit
• Refer to Cable Specifications in this page for details on
cables.
Master clock
Fi
re
y&
In
te
llig
en
tS
ec
ur
it
WJ-SX150 SETUP PROCEDURES
49
SETUP PROCEDURES
■ Setup Procedures
Notes:
• To use WJ-SX150 Administrator Console, you need to
prepare a PC and a 9-pin D-sub cable.(Refer to p. 47.)
• When changing the configuration of WJ-SX150
Administrator Console, configuration data getting and
putting are necessary between the unit and PC to activate your configuration.
This unit has two setting procedures.
The one is SETUP MENU, which is the unit's on-screen display (OSD).
The other is WJ-SX150 Administrator Console, which operates on the PC.
Sequence settings
• Tour sequence
• Group sequence
■ Description of Setup Procedures
Alarm settings
• Alarm mode
• Alarm event
• Alarm input/Alarm port
Fi
re
This chapter describes about configurable items.
● Sequence Settings
SETUP MENU can configure tour sequences. WJ-SX150
Administrator Console can configure both of tour
sequences and group sequences.
• Tour sequence: Up to 16 tour sequences are configurable (16 steps per tour).
• Group sequence: Tour sequences can be activated on
up to 4 monitors simultaneously (1 tour sequence per
monitor).
ec
System settings
• Clock (Time and date) *1
• Cable compensation
• Camera title
• Data port *2
ur
it
Operator settings
• Operator registration
• Level table
• Monitor select (Monitor selection)
• Auto login/logout (Auto log-in/log-out)
y&
SETUP MENU (OSD)
● Schedule Settings
tS
Multiplxer board
• Recorder
• Multiplexer *3
• Mux (Multiplxer camera title) *3
en
WJ-SX150 Administrator Console (PC)
Schedule settings
• Timer event
• Camera cleaning
• Daylight saving time
llig
Setup file operation
• Put a file to SX150
• Get a configuration data from the SX150
te
SX150 Admin Console Configuration
• File Open
• Account Manager
• Communication (Serial) port
SETUP MENU can configure daylight saving time. WJSX150 Administrator Console can configure timer event,
camera cleaning, and daylight saving time.
• Timer event: A sequence or spot mode can be activated on the regular time of every month, week or day.
Up to 30 timer events can be registered.
• Camera cleaning: Camera cleaning can be executed
on the regular time of every month, week or day.
• Daylight saving time: Daylight saving times for 20 years
are configurable.
In
• Camera manual cleaning ON/OFF
*1 WJ-SX150 Administrator Console can configure the
display pattern.
*2 WJ-SX150 Administrator Console can configure the
communication speed (baud rate) of the ports Data 1 to 4.
*3 These menus (or windows) appear only when the Multiplxer
is installed in the unit.
• SETUP MENU (OSD)
The basic functions, which are essential for the operation,
are configurable. However, some items are not configurable. The settings about group sequences, operators and
schedules, etc.
• WJ-SX150 Administrator Console (PC)
All the functions of this unit are configurable. You need a
PC to use WJ-SX150 Administrator Console.
Refer to p. 64 WJ-SX150 ADMINISTRATOR CONSOLE for
details of the platform and installation.
50
● Alarm Settings
The operation parameters when an alarm is input to the unit
are configurable.
• Alarm mode: The operation mode activated along with
an alarm input is configurable. Sequence mode or hold
mode is selectable. Alarm mode can be set to OFF
when not using it.
• Alarm event: The event activated along with an alarm
input is assignable to each alarm input terminals. The
sequence number or spot camera is selectable for the
alarm event.
• Alarm input (Alarm port): The alarm polarity (N. O. or N.
C.) is assignable to each alarm input terminal. One of
16 terminals is assignable for time adjustment.
● Multiplexer
• It is also selectable whether to activate the recording
and sequence/spot image monitoring when an alarm
signal is input to the unit. Alarm recording without the
sequence/spot image monitoring is also available.
• Recorder: The type and unit address of the recorder
are configurable.
• MULTIPLEXER: The parameters of the recorder mode
are configurable. You can set the alarm and normal
recording rate. You can also activate/deactivate
dynamic recording, dummy black, and CAM SW LOSS”
indication.
• MUX (Multiplxer) CAMERA TITLE: Camera titles which
are displayed with Multiscreen segments are configurable.
● Operator Settings
If you control this unit with a terminal-mode system controller, your operator information, controllable monitors and
auto log-in/log-out will be registrable and configurable.
• Operator registration: Up to 16 operators are available.
ID and password for operator identification are configurable. Level and priority can be assigned to each
operator. Each camera's control coverage is also configurable.
• Level table: Restriction level for each password is customizable.
• Monitor select (Monitor selection): Controllable monitor
can be assigned to each controller.
• Auto login/logout (Auto log-in/log-out): Auto log-in/logout is configurable for each controller.
y&
Fi
re
WJ-SX150 Administrator Console can send a configuration
file from the PC to this unit. The utility can also send the file
from the unit to the PC for configuration.
• Put to a file: A configuration data is sent from the PC to
the unit.
• Get from a file: A configuration data is sent from the unit
to the PC.
• Select setup data file: A configuration data is selected
when sending it from the PC to the unit (or from the unit
to the PC.)
ur
it
Note: These settings are configurable only through WJSX150 Administrator Console.
● WJ-SX150 Administrator Console
Configuration
tS
ec
Notes:
• These settings (except Operator registration) are configurable only through WJ-SX150 Administrator
Console. Operator registration is configurable through
SETUP MENU and WJ-SX150 Administrator Console.
• When you control the unit with a PS·Data system controller, the above settings will be invalid. Refer to the
system controller's operating instructions.
● Setup File Operation
● System Settings
llig
en
SETUP MENU can configure the clock (time and date),
cable compensation and camera title.
Besides these settings, WJ-SX150 Administrator Console
can select the data ports' baud rates.
In
te
• Clock (Time and date): The unit's time and date are
configurable.
• Cable compensation: Cable compensation type is
selectable depending on the distance between a camera and the unit. It is also possible to determine whether
to send the VD2 timing pulse or control data with the
camera output signals.
• Camera title: Camera title is configurable to identify the
camera images on the monitor. WJ-SX150 Administrator
Console can configure the camera title including original characters.
• Data port: Usually, the ports DATA 1 to 3 connect to the
terminal-mode system controllers. RS-485 cameras will
be connectable with the data port configurations
through WJ-SX150 Administrator Console and SETUP
MENU.
When you use the system controllers via the PS·Data
protocol, you need to configure the DATA 4 port setting
through SX150 Admin Console or SETUP MENU.
• EXT IN: External synchronization of the EXT IN connector is set to ON or OFF.
51
The PC-related settings are configurable.
• Account Manager: WJ-SX150 Administrator Console
operators are registrable and changeable.
• Communication (Serial) port: PC's usable communication port number and its baud rate (communication
speed) are configurable.
WJ-SX150 SETUP MENU (OSD)
The WJ-SX150 SETUP MENU (SETUP MENU) enables function controls that are not available by direct operation.
Note: Only one operator can enter SETUP MENU.
1. Confirm that the camera and peripherals are correctly
and securely connected and that all components are
turned on.
Joystick to L(A): Moves the cursor to the left.
Joystick to R (B): Moves the cursor to the right.
PREV button: Selects the previous mode or parameter.
NEXT button: Selects the next mode or parameter.
Numeric buttons: Enters numerals.
CLEAR button: Deletes a character when editing a
camera title.
CAM (SET) button: Executes the selections and displays a submenu for items with the (O) mark.
MON (ESC) button: Returns to SETUP MENU or the
previous menu.
This operating instructions uses the symbols to
describe the buttons.
2. To execute the selection, select one of the monitors (1
to 4) by pressing the numeric button, then press the
MON (ESC) button.
The MONITOR indicator will light up.
4. To end the setting and return to the normal view, press
the SETUP button while holding down the SHIFT button
when SETUP MENU is displayed.
The system controller's SETUP indicator will go off.
■ Displaying SETUP MENU
y&
ur
it
Note: The Multiplexer board version, “900 MULTIPLEXER”, and “1000 MUX CAMERA TITLE” is displayed
only when the Multiplexer board is installed in the
unit.
tS
ec
3. Press the SETUP button while holding down the SHIFT
button on the system controller.
WJ-SX150 SETUP MENU will appear on the active monitor as shown below, and the system controller's SETUP
indicator will light up.
The tree of SETUP MENU is shown in the next page.
Note: “x.xx” in SETUP MENU shows the firmware version.
Fi
re
To display SETUP MENU, follow the procedure below.
WJ-SX150 SETUP MENU
llig
SEQUENCEO
ALARMO
CAMERA TITLEO
RECORDERO
SYSTEMO
OPERATOR REGISTRATIONO
te
300
400
500
600
700
800
Aug/21/2002 10:55 AM
ON
en
100 TIME&DATE
200 D.S.T.
x.xx
(Without the Multiplexer board)*
SETUP
In
* This is the factory default setting.
WJ-SX150 SETUP MENU
SHIFT
100 TIME&DATE
200 D.S.T.
300
400
500
600
700
800
x.xx/x.xx
As shown in the tree, SETUP MENU has seven main submenus:
TIME & DATE, D. S. T., SEQUENCE SETUP, ALARM
SETUP, CAMERA TITLE, SYSTEM SETUP and OPERATOR
REGISTRATION.
SEQUENCE SETUP, ALARM SETUP, CAMERA TITLE, SYSTEM SETUP and OPERATOR REGISTRATION are further
divided into additional submenus.
The (O) mark indicates that the item has a submenu for
more detailed setups.
Refer to the figure in next page for the composition of
SETUP MENU.
Aug/21/2002 10:55 AM
ON
SEQUENCEO
ALARMO
CAMERA TITLEO
RECORDERO
SYSTEMO
OPERATOR REGISTRATIONO
900 MULTIPLEXERO
1000 MUX CAMERA TITLEO
(With the Multiplexer board)
The following functions and buttons are valid in SETUP
MENU:
Joystick to UP(D): Moves the cursor up or returns to
the previous page.
Joystick to DOWN(C): Moves the cursor down or displays the next page.
52
■ Programming SETUP MENU
■ TIME & DATE
WJ-SX150 SETUP MENU
100 TIME&DATE
200 D.S.T.
300
400
500
600
700
800
x.xx/x.xx
Aug/21/2002 10:55 AM
ON
SEQUENCEO
ALARMO
CAMERA TITLEO
RECORDERO
SYSTEMO
OPERATOR REGISTRATIONO
900 MULTIPLEXERO
1000 MUX CAMERA TITLEO
● How to Display
To display this menu on the monitor, move the cursor to 100
TIME & DATE in SETUP MENU by moving the joystick to D
or C.
● Parameters
You can move the cursor to each parameter by moving the
joystick to A or B.
• Month
Press the NEXT or PREV button to select the correct month.
In
te
llig
en
tS
ec
ur
it
y&
Fi
re
• Day
Press the numeric buttons to enter it directly.
53
x.xx/x.xx
WJ-SX150 SETUP MENU
100 TIME&DATE
200 D.S.T.
300
400
500
600
700
800
300 SEQUENCE
TOUR NO. =1
Aug/21/2002 10:55 AM
ON
STEP CAM
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
SEQUENCEO
ALARMO
CAMERA TITLEO
RECORDERO
SYSTEMO
OPERATOR REGISTRATIONO
900 MULTIPLEXERO
1000 MUX CAMERA TITLEO
PRE DWELL
-2S
-2S
-2S
-2S
-2S
-2S
-2S
-2S
STEP CAM
9
9
10 10
11 11
12 12
13 13
14 14
15 15
16 16
PRE DWELL
-2S
-2S
-2S
-2S
-2S
-2S
-2S
-2S
420 ALARM EVENT
Outside the U. S.:
· Aug/21/2002... 21/08/2002
· D. S. T.... SUMMER TIME
400 ALARM
410 ALARM MODE
SEQUENCE / DWELL 2sec
420 ALARM EVENTO
ALARM INPUT
430
CAMERA
OFF
440
ALARM PORT
ONO
450
SERIAL PORT
ON
460
MUX MOTION DET OFFO
500 CAMERA TITLE
2 of 2
1
2
3
4
5
6
7
8
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
OFF
1
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
700 SYSTEM
COMPENSATION/VD2/DATAO
RS485 CAMERAO
DATA4/PSD PORT SELECT PSD
PSD/HDR PORT SPEED
9600bps
SERIAL PORT SPEED
38400bps
tS
710
720
730
740
750
ec
ur
it
610 REDORDER CONTROL
620 RECORDER UNIT ADDRESS
9
10
11
12
13
14
15
16
y&
600 RECORDER
1 of 2
/ PRE01
/ PRE01
PRE-/ PRE01
PRE-/ PRE01
PRE-/ PRE01
PRE-/ PRE01
PRE-/ PRE01
PRE-/ PRE01
PRE-PRE--
440 ALARM INPUT(ALARM PORT)
1 of 2
Fi
re
500 CAMERA
TITLE
CAM
TITLE
9 C09
CAM 10
TITLE
C10
1 11 C11
2 12 C12
3 13 C13
4 14 C14
5 15 C15
6 16 C16
7
8
2 of 2
420 ALARMALM
EVENT
MON MODE
9
1 SPOT1
ALM 10MON 1MODE
SPOT1
/
1 11 1 1CAM01
SPOT1
/
2 12 1 1CAM02
SPOT1
/
3 13 1 1CAM03
SPOT1
/
4 14 1 1CAM04
SPOT1
/
5 15 1 1CAM05
SPOT1
/
6 16 1 1CAM06
SPOT1
7
1 CAM07 /
8
1 CAM08 /
GENLOCK OFF
770 CAMERA CLEANING
OFF
en
760 EXT IN
llig
ID
=150
PASSWORD=*****
PRIORITY=1
LEVEL
=1
CAM01=VIEW&CONTROL
CAM02=VIEW&CONTROL
CAM03=VIEW&CONTROL
CAM04=VIEW&CONTROL
CAM05=VIEW&CONTROL
CAM06=VIEW&CONTROL
CAM07=VIEW&CONTROL
CAM08=VIEW&CONTROL
CAM09=VIEW&CONTROL
CAM10=VIEW&CONTROL
CAM11=VIEW&CONTROL
CAM12=VIEW&CONTROL
CAM13=VIEW&CONTROL
CAM14=VIEW&CONTROL
CAM15=VIEW&CONTROL
CAM16=VIEW&CONTROL
In
te
OPERATOR NO.=01
900 MULTIPLEXER
EXT.
EXT.
OFF
OFF
ON
1000 MUX CAMERA TITLE
CAM
1
2
3
4
5
6
7
8
54
TITLE
C01
C02
C03
C04
C05
C06
C07
C08
CAM
9
10
11
12
13
14
15
16
CAM COMP VD2
1 S
ON
2 S
ON
3 S
ON
4 S
ON
5 S
ON
6 S
ON
7 S
ON
8 S
ON
DATA
ON
ON
ON
ON
ON
ON
ON
ON
CAM COMP VD2
9 S
ON
10 S
ON
11 S
ON
12 S
ON
13 S
ON
14 S
ON
15 S
ON
16 S
ON
620 RS485 CAMERA
800 OPERATOR REGISTRATION
VCR REC MODE
910
ALARM
920
NORMAL
930 DYNAMIC REC
940 DUMMY BLACK
950 CAM SW LOSS
610 COMPENSATION/VD2/DATA
TITLE
C09
C10
C11
C12
C13
C14
C15
C16
CAM
1
2
3
4
5
6
7
8
PORT
---------
CAM
9
10
11
12
13
14
15
16
PORT
---------
DATA
ON
ON
ON
ON
ON
ON
ON
ON
■ D. S. T. (Daylight Saving Time)
• Year
Press the numeric button to enter the correct year.
WJ-SX150 SETUP MENU
• TIME
Press the numeric button to enter the correct time.
100 TIME&DATE
200 D.S.T.
300
400
500
600
700
800
• MINUTE
Press the numeric button to enter the correct minute.
x.xx/x.xx
Aug/21/2002 10:55 AM
ON
SEQUENCEO
ALARMO
CAMERA TITLEO
RECORDERO
SYSTEMO
OPERATOR REGISTRATIONO
900 MULTIPLEXERO
1000 MUX CAMERA TITLEO
• AM/PM
Press the NEXT or PREV button to select the correct time.
After the configuration, press the SETUP button while holding down the SHIFT button. The configuration will be updated when closing SETUP MENU.
Notes:
• Adjust the time and date when the clock display is different from the current one.
• The clock display pattern is changeable with the setting in
WJ-SX150 Administrator Console. (Refer to p. 77.) The
factory default setting is Month/Day/Year.
• The clock is automatically adjusted to 0 second of the setting time and date when closing SETUP MENU.
• Hour system (12- hours or 24- hours) is changeable
through WJ-SX150 Administrator Console.
● How to Display
To display this menu on the monitor, move the cursor to 200
D. S. T. in SETUP MENU by moving the joystick to ▼ or ▲.
Fi
re
● Parameters
Select ON or OFF by pressing the NEXT or PREV buttons.
y&
ON: Daylight saving time is activated.
OFF: Daylight saving time is deactivated.
The factory default setting is ON.
ur
it
After the configuration, press the SETUP button while holding down the SHIFT button. The configuration will be updated when closing SETUP MENU.
In
te
llig
en
tS
ec
Note: The start/end date are configurable through WJSX150 Administrator Console. (Refer to p. 71.)
■ SEQUENCE SETUP
300 SEQUENCE
TOUR NO. =1
STEP CAM
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
PRE DWELL
-2S
-2S
-2S
-2S
-2S
-2S
-2S
-2S
STEP CAM
9
9
10 10
11 11
12 12
13 13
14 14
15 15
16 16
PRE DWELL
-2S
-2S
-2S
-2S
-2S
-2S
-2S
-2S
● How to Display
To display this menu on the monitor, move the cursor to 300
SEQUENCE in SETUP MENU by moving the joystick to ▼ or
▲.
Then, press the CAM (SET) button. The submenu appears
on the monitor.
● Parameters
Move the joystick to move the cursor.
Press the NEXT or PREV button to select the desired parameters.
Press the numeric button(s) to enter a number.
55
● Parameters
TOUR NO: Press the NEXT or PREV button to select the
tour number. Or press the numeric button(s) to
enter a number.
STEP: This stands for a tour sequence step.
CAM: This stands for a camera number. CAM 0 to 16 is
selectable. CAM 0 deactivates the sequence step.
Move the joystick to move the cursor.
Press the NEXT or PREV button to select the desired parameters.
Press the numeric button(s) to enter a number.
• ALARM MODE
You can select an operation mode when alarm input signals
are accepted by the unit.
The factory default setting is assigned to each step
in numerical order (STEP 1 = CAM 1, STEP 2 =
CAM 2, STEP 3 = CAM 3, STEP = 4, CAM 4, STEP 5
= CAM 5…)
PRE: This stands for a camera’s preset position number. 1 to 64 or "- -" is selectable. When the camera
has no preset position, select "- -". You can set "- -"
by pressing the button 0.
The factory default setting is "- -".
Notes:
• The alarm mode is activated when alarm input signals
are assigned to the same monitor through 420 ALARM
EVENT or the Alarm Event (refer to p. 74) window.
• While alarm is activated, you cannot operate the functions related to the multiplexer board.
DWELL: This stands for the dwell time. 1 second to 30
seconds are selectable. If you enter 0, the
sequence step will be skipped.
The factory default setting is 2S for each step.
Fi
re
SEQUENCE: An alarm operation is replaced by another one after the dwell time (DWELL) ends.
HOLD: An initial alarm operation is continued even after
another alarm input is accepted.
OFF: Select this when not using the alarm mode.
The factory default setting is SEQUENCE.
The factory default setting is 2 seconds.
400 ALARM
te
■ ALARM SETUP
llig
en
tS
ec
Notes:
• A preset position number is available only when a combination camera is selected for CAM.
• The available preset position numbers differ among
cameras. Refer to each camera's operating instructions.
• DWELL
This stands for the dwell time of a sequence during an
alarm mode.
1 to 30 seconds are selectable.
ur
it
After all the configurations, press the SETUP button while
holding down the SHIFT button. The configuration will be
updated when closing SETUP MENU.
y&
After the configuration, press the MON (ESC) button. The
monitor display will return to the previous menu.
420 ALARM EVENT
ALM
1
2
3
4
5
6
7
8
MON
1
1
1
1
1
1
1
1
1 of 2
MODE
CAM01
CAM02
CAM03
CAM04
CAM05
CAM06
CAM07
CAM08
/
/
/
/
/
/
/
/
PRE-PRE-PRE-PRE-PRE-PRE-PRE-PRE--
In
410 ALARM MODE
SEQUENCE / DWELL 2sec
420 ALARM EVENT
ALARM INPUT
430
CAMERA
OFF
440
ALARM PORT
ONO
450
SERIAL PORT
ON
460
MUX MOTION DET OFFO
• ALARM EVENT
This item is configurable in 420 ALARM EVENT.
Move the cursor and press the CAM (SET) button.
420 ALARM EVENT will appear on the monitor.
● How to Display
To display this menu on the monitor, move the cursor to 400
ALARM in SETUP MENU by moving the joystick to ▼ or ▲.
Then, press the CAM (SET) button. The submenu appears
on the monitor.
56
420 ALARM EVENT
ALM
9
10
11
12
13
14
15
16
MON
1
1
1
1
1
1
1
1
2 of 2
MODE
CAM09
CAM10
CAM11
CAM12
CAM13
CAM14
CAM15
CAM16
/
/
/
/
/
/
/
/
PRE-PRE-PRE-PRE-PRE-PRE-PRE-PRE--
ALM: This stands for the alarm number.
MON: This stands for the monitor number.
MODE: This stands for the display mode of an alarm
image.
• CAMnn (nn is the camera number): Activates the
spot camera when an alarm input is accepted.
• PRE: This item stands for the preset position number of a CAMnn. Enter the desired preset position
number when selecting a combination camera.
When selecting another type of camera, select --.
• TOURnn (nn is a tour sequence number): Executes
a tour sequence when an alarm input is accepted.
OFF: An alarm input is not accepted via the ALARM
port.
The factory default setting is ON.
Each alarm input's polarity is configurable in 440 ALARM
INPUT (ALARM PORT).
Set ALARM PORT to ON or REC ONLY, and press the CAM
(SET) button.
440 ALARM INPUT (ALARM PORT) will appear on the monitor.
The factory default setting is the same as the two illustrations above.
Notes:
• MODE and PRE cannot be selected by pressing the
numeric buttons. Press the NEXT or PREV button for
selection.
• PRE doesn’t appear when TOUR 1 to 16 is selected for
MODE.
• When selecting a camera without the preset position
function, select "- -" for PRE.
• When moving the joystick to ▼ at the bottom of ALARM
EVENT 1 of 2, the monitor will display 2 of 2 (the next
page).
• When moving the joystick to ▲ at the top of ALARM
EVENT 2 of 2, the monitor will display 1 of 2 (the previous page).
9
10
11
12
13
14
15
16
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
Fi
re
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
y&
To select an alarm input polarity required for the ALARM
port, press the PREV or NEXT button.
N.O.: Selects Normally Open alarm contact.
N.C.: Selects Normally Closed alarm contact.
TIME: Enables the input for time adjustment.
The factory default setting is N.O.
ec
• ALARM INPUT
1
2
3
4
5
6
7
8
ur
it
After the configuration, press the MON (ESC) button. The
monitor display returns to ALARM SETUP.
440 ALARM INPUT(ALARM PORT)
In
te
llig
en
tS
CAMERA
This stands for that an alarm input is accepted via the
CAMERA IN connectors or the RS-485 ports.
ON: The alarm-associated sequence/spot image is displayed on a monitor, and alarm recording will start
(if a recorder is connected to the unit).
REC ONLY: Only alarm recording will start and monitors will keep displaying the current sequence/spot
images.
Note: You cannot recover alarm-related operations
from system controllers when REC ONLY is
selected.
OFF: An alarm input is accepted neither via the CAMERA IN connectors nor the RS-485 ports.
The factory default setting is OFF.
ALARM PORT
This stands for that an alarm input is accepted via the
ALARM port (25-pin D-sub connector at the rear panel).
ON: The alarm-associated sequence/spot image is displayed on a monitor, and alarm recording will start
(if a recorder is connected to the unit.)
REC ONLY: Only alarm recording will start and monitors will keep displaying the current sequence/spot
images.
Note: You cannot recover alarm-related operations
from system controllers when REC ONLY is
selected.
57
Notes:
• Use N.O. type master clock.
• If TIME is selected, an alarm input terminal can adjust
the clock by ±30 seconds with an N.O. type signal
input. For example, when the clock time is between
00:59:30 and 01:00:30, it will be automatically adjusted
to 01:00:00 by the master clock.
After the configuration, press the MON (ESC) button. The
monitor display returns to 400 ALARM SETUP.
SERIAL PORT
This stands for that an alarm input is accepted via the
SERIAL port. The alarm-associated sequence/ spot
image is displayed on a monitor, and alarm recording
will start (if a recorder is connected to the unit).
ON: The alarm-associated sequence/spot image is displayed on a monitor, and alarm recording will start
(if a recorder is connected to the unit.)
REC ONLY: Only alarm recording will start and monitors will keep displaying the current sequence/spot
images.
Note: You cannot recover alarm-related operations
from system controllers when REC ONLY is
selected.
OFF: An alarm input is not accepted via the SERIAL
port.
The factory default setting is ON.
• MUX MOTION DET
This menu appears only when the Multiplexer board is
installed in the unit.
This stands for that the unit’s motion detector is activated when a camera detects the brightness-level change
and transmit an alarm signal.
ON: The alarm-associated sequence/spot image is displayed on a monitor, and alarm recording will start
(if a recorder is connected to the unit.)
REC ONLY: Only alarm recording will start and monitors will keep displaying the current sequence/spot
images.
Note: You cannot recover alarm-related operations
from system controllers when REC ONLY is
selected.
OFF: An alarm input is not accepted by the motion
detector.
+
+
Fi
re
Setting point
To configure where to activate the motion detector, set
MUX MOTION DET to ON or REC ONLY, and press the
CAM (SET) button. The live image will be displayed.
ur
it
y&
Note: Black image will be displayed on the monitor if
the currently selected channel has no camera connection.
2. Move the “+” mark to the desired area, and then press
the CAM (SET) key. Setting point 2 is determined and
the “+” mark will disappear. Then, the mark will appear
again at the center of the monitor. The square, covered
with Setting point 1 and 2, is showing the motion-detection area.
Note: White images will be displayed in the square if the
currently selected channel has no camera connection.
tS
ec
A “+” mark appears at the center of the monitor.
+
Setting point 2
Mark
+
llig
en
Setting point 1
The following is the setting procedure.
In
te
1. Move the cursor with the joystick to the desired area,
and then press the CAM (SET) key. Setting point 1 is
determined.
58
3. To configure more motion-detection area, repeat Step 1
and 2.
Up to 4 motion-detection areas are available.
■ CAMERA TITLE
Notes:
• If you repeat Step 1 after setting 4 motion-detection
areas, “NG” will blink at the center of the monitor for two
seconds.
• To reset a motion-detection area, move the “+” mark on
the desired area. Then, press the CLEAR button. The
area will be reset.
• If an area overlaps another one, the newer area will be
reset.
500 CAMERA TITLE
CAM
1
2
3
4
5
6
7
8
1 of 2
TITLE
5. To configure the motion-detector areas of another camera channel, press the NEXT or PREV button.
500 CAMERA TITLE
6. Repeat Step 1 to 4.
CAM
9
10
11
12
13
14
15
16
y&
● How to Display
To display this menu on the monitor, move the cursor to 500
CAMERA TITLE in SETUP MENUby moving the joystick to
▼ or ▲. Then, press the CAM (SET) button. The submenu
appears on the monitor.
ur
it
After the configuration, press the MON (ESC) button. The
motion-detection setting will be memorized and the monitor
display will return to the previous menu.
● How to edit
In
te
llig
en
tS
ec
After all the configurations, press the SETUP button while
holding down the SHIFT button. The configuration will be
updated when closing SETUP MENU.
TITLE
Fi
re
Notes:
• If you press the CLEAR button before determining four
motion-detection areas, all the areas of the channel will
be reset.
• Setting point 1 and 2 are determined only when the “+”
mark has moved 5 segments both vertically and horizontally.
2 of 2
A camera title is composed of up to 20 characters.
Each camera number is fixed and the subsequent 20 characters are editable.
The characters available here are the following:
ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrs
tuvwxyz0123456789!"#$%&'()*+,-./:;=?•_(space)
The factory default settings are same as the illustrations.
1. Edit the camera titles by pressing the NEXT or PREV
buttons.
The NEXT button toggles these characters in this order.
The PREV button toggles these characters in a reverse
order.
Joystick and the CLEAR button are also usable for the
edit. (Refer to p. 52 Displaying SETUP MENU for each
use.)
2. After the configuration, press the MON (ESC) button.
The monitor display will return to the previous menu.
After all the configurations, press the SETUP button while
holding down the SHIFT button. The configuration will be
updated when closing SETUP MENU.
Notes:
• When moving the joystick to ▼ at the bottom of CAMERA TITLE 1 of 2, the monitor will display 2 of 2 (the
next page).
59
• When moving the joystick to ▲ at the top of CAMERA
TITLE 2 of 2, the monitor will display 1 of 2 (the previous
page).
• Original characters
are configurable through WJSX150 Administrator Console, but they are not displayed correctly in SETUP MENU. They are displayed
as ■. (Refer to p. 80 Edit Font window.)
With the Multiplexer board
VCR: Select this when a time-lapse VCR is connected
to the unit.
HD100: Select this when a WJ-HD100 Series recorder
is connected to the unit.
OFF: Select this when no recorder is connected to the
unit.
The factory default setting is OFF.
■ RECORDER
• RECORDER UNIT ADDRESS
This stands for the recorder’s unit address.1 to 99 is
available.
600 RECORDER
610 REDORDER CONTROL
620 RECORDER UNIT ADDRESS
HD500
1
Fi
re
■ SYSTEM SETUP
700 SYSTEM
COMPENSATION/VD2/DATAO
RS485 CAMERAO
DATA4/PSD PORT SELECT PSD
PSD/HDR PORT SPEED
9600bps
SERIAL PORT SPEED
38400bps
y&
710
720
730
740
750
GENLOCK OFF
770 CAMERA CLEANING
OFF
ec
To display this menu on the monitor, move the cursor to 600
RECORDER in SETUP MENU by moving the joystick to D
or C. Then, press the CAM (SET) button. The submenu will
appear on the monitor.
760 EXT IN
ur
it
● How to Display
tS
● Parameters
llig
en
Move the joystick to move the cursor.
Press the NEXT or PREV button to select the desired parameters.
Press the numeric button(s) to enter a number.
In
te
• RECORDER CONTROL
This stands for the recorder type. The selectable parameters differ depending on the existing of the
Multiplexer board installation.
Without the Multiplxer board
HD500: Select this when a WJ-HD500 Series recorder
is connected to the unit.
OFF: Select this when no recorder is connected to the
unit.
The factory default setting is HD500.
● How to Display
To display this menu on the monitor, move the cursor to 600
SYSTEM in SETUP MENU by moving the joystick to ▼ or ▲.
Then, press the CAM (SET) button. The submenu appears
on the monitor.
● Parameters
Move the joystick to move the cursor.
Press the NEXT or PREV button to select the desired parameters.
• COMPENSATION/VD2/DATA
This menu links to the submenu.
Move the cursor and press the CAM (SET) button to go into
the menu.
710 COMPENSATION/VD2/DATA will appear on the monitor.
710 COMPENSATION/VD2/DATA
CAM COMP VD2
1 S
ON
2 S
ON
3 S
ON
4 S
ON
5 S
ON
6 S
ON
7 S
ON
8 S
ON
60
DATA
ON
ON
ON
ON
ON
ON
ON
ON
CAM COMP VD2
9 S
ON
10 S
ON
11 S
ON
12 S
ON
13 S
ON
14 S
ON
15 S
ON
16 S
ON
DATA
ON
ON
ON
ON
ON
ON
ON
ON
CAM: This stands for the camera number.
COMP: This stands for cable compensation.
• DATA4/PSD PORT SELECT
This stands for the operation mode: PS·Data or the terminal
mode.
Select the desired setting according to the cable length.
PSD: Select this when connecting a PS·Data controller
to the DATA 4 port.
DATA 4: Select this when connecting a terminal-mode
controller to the DATA 4 port.
S: Less than 400 m (1 300 ft)
M: 400 m (1 300 ft) to 700 m (2 300 ft)
L: 700 m (2 300 ft) to 900 m (3 000 ft)
The factory default setting is PSD.
Refer to p. 37 for available cables.
The factory default setting is S.
• PSD/HDR PORT SPEED
This stands for the PS·Data communication speed (or baud
rate) of the DATA 4 port.
19200, 9600 or 4800 bps is selectable.
VD2: To send the VD2 timing pulse with the camera
output signal, select ON. Not to send the VD2 timing pulse with the camera output signal, select OFF.
The factory default setting is ON.
DATA: To send the control data with the camera output
signal, select ON. Not to send the control data with
the camera output signal, select OFF. The factory
default setting is ON.
Fi
re
The factory default setting is 9600 bps.
• SERIAL PORT SPEED
Select the desired communication speed for SERIAL (the
serial port), with the NEXT or PREV button.
After the configuration, press the MON (ESC) button. The
monitor display returns to the previous menu.
PORT
---------
In
te
CAM: This stands for the camera number.
PORT: This stands for the data port to which an RS-485
type camera is connected. The following are the
parameters.
• --(DISABLE): Select this when using the camera
via coaxial communication or not using the camera.
• RS485: Select this when connecting the camera to
an RS-485 port.
• DATA1: Select this when connecting the camera
to the DATA 1 port.
• DATA 2: Select this when connecting the camera
to the DATA 2 port.
• DATA 3: Select this when connecting the camera
to the DATA 3 port.
The factory default setting is DISABLE (for CAM 1 to
16).
Note: The settings of camera inputs without camera connections are ignored.
61
y&
tS
CAM
9
10
11
12
13
14
15
16
en
PORT
---------
llig
CAM
1
2
3
4
5
6
7
8
The factory default setting is 38400 bps.
After the configuration, press the MON (ESC) button. The
monitor display will return to the previous menu.
ec
720 RS485 CAMERA
ur
it
• RS485 CAMERA SETUP
This menu links to the submenu.
Move the cursor and press the CAM (SET) button to go into
the menu. 720 RS485 CAMERA will appear on the monitor.
38400 bps: The speed is set to 38400 bps.
19200 bps: The speed is set to 19200 bps.
9600 bps: The speed is set to 9600 bps.
4800 bps: The speed is set to 4800 bps.
After all the configurations, press the SETUP button while
holding down the SHIFT button. The configuration will be
updated when closing SETUP MENU.
• EXT IN
This stands for the setting of the EXT IN connector at the
unit's rear panel.
This menu does not appear when the Multiplexer board is
installed in the unit.
GENLOCK
ON: Select this mode to gen-lock the unit with the
recorder.
OFF: Select this mode if the asynchronous unit is connected with the recorder.
The factory default setting is GENLOCK OFF.
Notes:
• If GENLOCK ON is selected, the playback images or
multiscreen display cannot be displayed on Monitor 1
to 4. Confirm the images on the monitor which are connected to the recorder.
• If GENLOCK OFF is selected, the maximum rate
recording becomes unavailable (when WJ-HD500A is
connected to the unit).
• CAMERA CLEANING
• PRIORITY
This stands for an operator's priority. 1 to 16 is available.
(Refer to p. 14 for details on Priority Lock.)
ON: Activates the manual cleaning for the cameras.
OFF: Deactivates the manual cleaning.
• LEVEL
This stands for an operator's restrict level. It is configurable
through Level Table (refer to p. 76) of WJ-SX150
Administrator Console what kind of restriction is given to the
operator. 1 to 3 is available.
When you set CAMERA CLEANING to ON and exit from the
SETUP MENU, camera cleaning will start.
The factory default setting is OFF.
• CAM 01 to 16:
These stand for an operator's camera operation coverage.
The following are the parameters.
Notes:
• When the camera cleaning is active, cleaning will begin
from CAM 1 in numerical order.
• Surveillance is impossible during the cleaning.
• The cleaning cannot be stopped after it is started.
• Refer to pp. 38 and 39 for details on RS-485 or PS·Data
connections.
• The camera address needs to be corresponding with
the camera number.
Fi
re
VIEW & CONTROL: The operator can display the
camera image on the monitor and control panning/tilting.
VIEW ONLY: The operator can display the camera
image on the monitor, but cannot control the
panning/tilting.
PROHIBITED: The operator can neither display the
camera image on the monitor nor control the
panning/tilting.
y&
■ OPERATOR REGISTRATION
The following is the factory default setting of this menu.
800 OPERATOR REGISTRATION
ur
it
CAM09=VIEW&CONTROL
CAM10=VIEW&CONTROL
CAM11=VIEW&CONTROL
CAM12=VIEW&CONTROL
CAM13=VIEW&CONTROL
CAM14=VIEW&CONTROL
CAM15=VIEW&CONTROL
CAM16=VIEW&CONTROL
en
● How to Display
te
llig
To display this menu on the monitor, move the cursor to
800 OPERATOR REGISTRATION in SETUP MENU by moving the joystick to ▼.Then, press the CAM (SET) button. The
submenu appears on the monitor.
● Parameters
In
Move the joystick to move the cursor.
Press the NEXT or PREV button to select the desired parameters.
Press the numeric button(s) to enter a number.
• OPERATOR NO.
This stands for an operator number. When you enter the
number by pressing the NEXT, PREV or numeric button(s),
this menu will display the associated operator's information.
1 to 16 is available.
• ID
This stands for an operator ID. 1 to 99999 is available.
• PASSWORD
This stands for an operator's password. 1 to 99999 is available. The password will be displayed as "*" on the monitor.
62
OPERATOR NO.
1
2
3
4
5
6
ec
CAM01=VIEW&CONTROL
CAM02=VIEW&CONTROL
CAM03=VIEW&CONTROL
CAM04=VIEW&CONTROL
CAM05=VIEW&CONTROL
CAM06=VIEW&CONTROL
CAM07=VIEW&CONTROL
CAM08=VIEW&CONTROL
ID
=150
PASSWORD=*****
PRIORITY=1
LEVEL
=1
tS
OPERATOR NO.=01
ID
150
1
100
101
102
103
PASSWORD
150
12345
100
101
102
103
LEVEL
1
1
1
1
2
3
PRIORITY
1
2
3
4
5
6
CAM 1 to 16 = VIEW & CONTROL (for OPERATOR NO. 1 to
6
Note: When you enter an invalid number, the parameter will
return to the state before your numerical entry.
■ MULTIPLEXER
900 MULTIPLEXER
VCR REC MODE
910
ALARM
920
NORMAL
930 DYNAMIC REC
940 DUMMY BLACK
950 CAM SW LOSS
EXT.
EXT.
OFF
0FF
ON
● How to Display
This menu will appear only when the Multiplexer board
is installed in the unit. To display this menu on the monitor, move the cursor to 900 MULTIPLEXER in SETUP
MENU by moving the joystick to D or C. Then, press
the CAM (SET) button. The submenu appears monitor.
■ MUX CAMERA TITLE
● Parameters
Move the joystick to move the cursor.
Press the NEXT or PREV button to select the desired parameters.
1000 MUX CAMERA TITLE
CAM
1
2
3
4
5
6
7
8
• ALARM
EXT: Select this to gen-lock the unit with the recorder
when an alarm is input to the unit.
002,004 to 128 (field): Select one of these alarm
recording rates if the asynchronous unit is connected to the unit.
The factory default setting is EXT.
CAM
9
10
11
12
13
14
15
16
TITLE
C09
C10
C11
C12
C13
C14
C15
C16
● How to Display
This menu will appear only when the Multiplexer board is
installed in the unit. To display this menu on the monitor,
move the cursor to 1000 MUX CAMERA TITLE in SETUP
MENU by moving the joystick to D or C. Then, press the
CAM (SET) button. The submenu appears monitor.
Fi
re
• NORMAL
EXT: Select this to gen-lock the unit during the normal
operation.
002,004 to 255 (field): Select one of these normal
recording rates if the asynchronous unit is connected to the unit.
● How to edit
The factory default setting is EXT.
ur
it
y&
The factory default settings are same as illustrations.
The editing procedure is the same as 500 CAMERA TITLE.
(Refer to p. 59.)
tS
ec
• DYNAMIC REC
PRI.: Select this to give recording priority to the camera
channel with the alarm input.
ONLY: Select this to record the images from the alarmassociated camera channel.
GROUP: Select this to give recording priority to a group
of up to 4 camera channels associated to the alarm
input.
OFF: Select this to deactivate the alarm priority mode.
en
The factory default setting is OFF.
In
te
llig
• DUMMY BLACK
ON: Select this to display the black picture for a camera channel that is not connected to the camera.
OFF: Select this to skip the camera channels that are
not connected to the camera in the sequence/spot
mode.
The factory default setting is ON.
• CAM SW LOSS
ON: Select this to make “SW LOSS” blinking on the
associated monitor when loss of the camera switching pulse is detected.
OFF: Select this not to make “SW LOSS” appear on the
associated monitor when loss of the camera switching pulse is detected.
The factory default setting is ON.
Note: If EXT is selected for 910 ALARM/920 NORMAL,
the playback images cannot be displayed on the
monitors which are not connected to the EXT IN
connector. Confirm the images on those which are
connected to the recorder.
63
TITLE
C01
C02
C03
C04
C05
C06
C07
C08
Notes:
• Up to 8 alphanumeric characters are available for
each multiplexer board camera title.
• When moving the joystick to D at the last text box
of CAM 8 TITLE, the cursor will move to the first text
box of CAM 9 TITLE.
• When moving the joystick to C at the first text box
of CAM 9 TITLE, the cursor will move to the last text
box of CAM 8 TITLE.
WJ-SX150 ADMINISTRATOR CONSOLE
■ Description of WJ-SX150
Administrator Console
• Intel and Pentium are trademarks of Intel Corporation.
• Microsoft® Windows® are either registered trademarks
of Microsoft Corporation in the United States and/or
other countries.
• VD2 is the original synchronization system of
Matsushita Communication Industrial Co., Ltd. and
Matsushita Electric Industrial Co., Ltd.
• Other company names and product names appearing
in the manual are registered trademarks or trademarks
of the company concerned.
WJ-SX150 Administrator Console is a utility software which
can configure the system settings and control data of this
surveillance system.
WJ-SX150 Administrator Console can configure the following settings.
● RECORDER
• Recorder (p. 66)
Platform
To install WJ-SX150 Administrator Console, the PC should
meet the following requirements.
• Hardware requirements
IBM PC or 100 % compatible, Pentium-400 MHz or
higher, 64 MB RAM, 2 MB hard drive space with additional space for configuration database (.sdt) and log.
In addition, the PC must be equipped with a serial port.
• Operating system requirements
Microsoft® Windows® 98, 98 SE, 2000, XP Professional
• Video display setting requirements
* High color (16 bit) or higher
* 800 x 600 resolution
When installing in the default system setting, the software is
installed in the following directory:
C: \Program Files\Panasonic\SX150
● MANAGEMENT
Fi
re
• Put a File to SX150 (p. 67)
• Get a Configuration Data from SX150 (p. 68)
y&
● SETUP
ur
it
Sequence Settings
• Tour Sequence (p. 68)
• Group Sequence (p. 69)
tS
ec
Schedule Settings
• Timer Event (p. 70)
• Camera Cleaning (p. 71)
• Daylight Saving Time/Summer Time (p. 71)
en
Alarm Settings
• Alarm Mode (p. 72)
• Alarm Event (p. 74)
• Alarm Port (p. 74)
In
te
llig
Operator Settings
• Operator Registration (p. 75)
• Level Table (p. 76)
• Monitor Selection (p. 76)
• Auto Login/Logout (Auto Log-in/Log-out) (p. 77)
System Settings
• Time & Date (p. 77)
• Cable Compensation/VD2/DATA (p. 78)
• Camera Title (p. 79)
• Data Port (p. 81)
Multiplexer Settings
• Multiplexer Mode (p. 82)
WJ-SX150 Administrator Console
• Select Setup Data File (p. 84)
• Account Manager (p. 85)
• Communication Port (p. 86)
Trademarks
• IBM is a trademark of International Business Machines
Corporation.
64
■ Installation/Uninstallation
● Installation
Insert the CD-ROM program disk into the CD-ROM drive on
the PC. Double-click "Setup.exe" to begin the installation.
Respond to the dialog boxes by following the directions
given.
● Uninstallation
1. Select "Start" – "Settings" – "Control Panel".
2. Click on the "Add/Remove Hardware" button.
3. Select WJ-SX150 Administrator Console and click on
"Add/Remove".
4. Operate according to the direction in the window.
● Before Using WJ-SX150 Administrator
Console
1. Select "Start" – "Program" – "Panasonic" – "WJ-SX150
Administrator Console x.xx*" or double-click the "WJSX150 Administrator Console x.x" icon on the desktop.
2. When you launch WJ-SX150 Administrator Console for
the first time, the following window will appear on the
PC screen.
Select “Yes”.
EXIT button
Minimizing button
→The selection will be memorized to WJ-SX150
Administrator Console while launching it.
Note: To change the selection you have done in the
"Startup Menu" window, restart the WJ-SX150
Administrator Console while holding down the SHIFT
key on the PC keyboard.
● Startup/Termination
Fi
re
1. Select "Start" – "Program" – "Panasonic" – "WJ-SX150
Administrator Console x.xx*" or double-click the "WJSX150 Administrator Console x.x" icon on the desktop.
* x.x: Software version
y&
3. When terminating the software, click on the EXIT button
or press the ESC button on the PC keyboard. The main
window will close and WJ-SX150 Administrator Console
will be terminated.
ur
it
ec
→The UserID and Password Required window will
appear on the PC screen.
Note: The operator name and password are changeable.
Operator addition is also available. The configuration of
each operator name, password and level are necessary. (Refer to p. 85 Account Manager.)
te
llig
en
tS
2. Enter "admin" and "sx150" in the boxes "Name" and
"Password" respectively.
Then, click on the OK button.
In
→WJ-SX150 Administrator Console starts up and the
main window will appear on the PC screen.
65
■ The Main Window
This window appears when starting up WJ-SX150
Administrator Console.
Clicking on each button in the window will display the associated configuration window.
Refer to the description of each window for details.
In addition, the main window has the following buttons.
RECORDER
(File Open):
Select Setup Data File window (p. 84)
(Recorder Control):
Recorder window (p. 66)
(Account Manager):
Account Manager window (p. 85)
MANAGEMENT
(Put to SX150):
Put a File to SX150 window (p. 67)
(Get from SX150):
Get a Configuration Data from SX150 window
(p. 68)
(Communication Port):
Communication Port window (p. 86)
(Panasonic):
Opens the version information window of WJSX150 Administrator Console. Clicking on "OK"
button will close the window.
SEQUENCE
(Tour Sequence): Tour Sequence window
(p. 68)
(Group Sequence): Group Sequence window
(p. 69)
Notes:
• To reflect each configuration to the system, save the file
by pressing the SAVE button before closing the window. After that, be sure to put the file from the PC to
the unit.
• When “No” is selected for Built in Multiplexer board in
the Recorder (refer to p. 66) window, you can open neither the Multiplexer Mode nor the Multiplexer Title window. Instead, a message window will appear and ask
you to select “Yes”. When the Multiplexer board is
installed in the unit, select “Yes”.
Fi
re
SCHEDULE
y&
(Timer Event):
Timer Event window (p. 70)
(Camera Cleaning):
Camera Cleaning window (p. 71)
(Daylight Saving Time/Summer Time):
Daylight Saving Time/Summer Time window
(p. 71)
ur
it
■ Recorder
ALARM
This window configures the recorder setting parameters:
whether the multiplexer board is installed in the unit, what is
the type of the recorder, what is the recorder unit address,
and whether the gen-lock is activated.
en
tS
ec
(Alarm Mode):
Alarm Mode window (p. 72)
(Alarm Event):
Alarm Event window (p. 74)
(Alarm Port):
Alarm Port window (p. 74)
OPERATOR
In
te
llig
(Operator Registration):
Operator Registration window (p. 75)
(Level Table):
Level Table window (p. 76)
(Monitor Selection):
Monitor Selection window (p. 76)
(Auto Login/Logout):
Auto Login/Logout window (p. 77)
SYSTEM
(Time & Date):
Time & Date window (p. 77)
(Cable Compensation/VD2/DATA):
Cable Compensation/VD2/DATA window (p. 78)
(Camera Title):
Camera Title window (p. 79)
(Data Port):
Data Port window (p. 81)
MULTIPLEXER
(Multiplexer Mode):
Multiplexer Mode window (p. 82)
(Multiplexer Title):
Multiplexer Title window (p. 84)
66
● How to Display
To display this window, click on the
button in the main window (p. 65).
(Recorder Mode)
● Parameters
Built in multiplexer board: Click on the desired radio button.
Yes: Select this when the multiplexer board is installed in
the unit. If you select this, you can configure the
Multiplexer Mode window. (Refer to p. 82.)
No: Select this when the multiplexer board is not installed in
the unit.
The factory default setting is “No”.
■ Put a File to SX150
Recorder Control: Click on the desired radio button to
determine the recorder type.
OFF: Select this when no recorder is connected to the
unit.
HD100: Select this when a WJ-HD100 Series recorder
is connected to the unit.
HD500: Select this when a WJ-HD500 Series recorder
is connected to the unit.
Pressing this button will start the putting of the configuration
data from the PC to the unit.
The factory default setting is HD500.
• Unit Address
This parameter is configurable only when HD100,
HD200 or HD500 is selected in the Recorder window.
When OFF is selected there, this parameter is displayed in gray and not configurable. 1 to 99 is selectable. The factory default setting is 1.
● How to Display
To display this window, click on the
SX150) button in the main window (p. 65).
Fi
re
● Parameters
Note: If you use a time-lapse VCR for the recorder, do the
recorder setting in SETUP MENU. (Refer to RECORDER
in p. 60.)
The file name of the configuration data appears.
y&
(OK) button
To put the configuration file from the PC to the unit, click on
this button.
ur
it
(Cancel Exit) button
To cancel the putting of the configuration data from the PC
to the unit, click on this button.
Notes:
• The setup file has been configured at the factory, and
the file names appear on the main window's title bar.
• Put the file from the PC to the unit when the time with no
necessary to the continuous system operation, such as
after-hours. After the file putting, the system will automatically restart. Then, the system controllers will temporarily log out.
• To change a file, select a file again. (Refer to p. 84
Select Setup Data File.)
• The configuration file cannot be put to the unit while
opening SETUP MENU.
• It takes a few seconds to put a file to SX150, and you
might assume the PC has been freezing.
Wait until the message “Completed!” appears on the
screen. If the message “Connection error” appears, the
PC is incorrectly connected to the unit. Confirm the settings of WJ-SX150 Administrator Console and retry the
file putting.
(Refer to p. 61 SERIAL PORT SPEED and p. 86
Communication Port.)
ec
• EXT IN: This stands for the setting of the EXT IN connector at the unit's rear panel.
GEN LOCK ON: Select this mode to gen-lock the unit
with the recorder.
GEN LOCK OFF: Select this mode if the asynchronous
unit is connected to the recorder.
In
te
llig
en
tS
Notes:
• If GENLOCK ON is selected, the playback images cannot be displayed on the monitors which are connected
to the connectors MONITOR OUT 1 to 4. Confirm the
images on those which are connected to the recorder.
• If GENLOCK OFF is selected, the maximum rate
recording becomes unavailable for WJ-HD500 Series.
• When a Multiplexer board is installed in the unit, you
can select either HD100 (Recorder window) or VCR
(610 RECORDER CONTROL in SETUP MENU). (Refer
to p. 60 for SETUP MENU.)
• When you select HD100 or VCR, make sure EXT IN is
set to GENLOCK OFF.
67
(Put to
■ Get a Configuration Data from SX150
■ Tour Sequence
Pressing this button will start the getting of the configuration
data from the unit to the PC.
This window configures the parameters of tour sequences:
the operating camera, dwell time*, preset position** in each
step.
Each sequence has up to 16 steps, and up to 16
sequences are configurable.
The configuration of a tour sequence can be copied to
another one.
* the display time of a camera image
** the panning/tilting position which has been preset in
advance
Notes:
• Enter the parameters from Step 1 in a sequential order.
If you skip a step, it will result in an error.
• After selecting a camera number, be sure to select the
dwell time, too. If you skip either of them, the message
requesting the parameter entry will appear.
● How to Display
To display this window, click on the
SX150) button in the main window (p. 65).
(Get from
Fi
re
● Parameters
The file name of the configuration data appears.
In
te
llig
en
tS
ec
Notes:
• The configuration data getting is also possible during
the surveillance, for it will not interfere with the system
operation.
• The past data will be overwritten when getting a new
configuration data.
• To change the getting directory, select it. (Refer to p. 84
Select Setup Data File.)
• When the file getting has been successfully executed,
“Completed!” will appear. If “Connection Error”
appears, confirm the connection and the serial port setting of the PC and the unit. (Refer to p. 47 and p. 72.) If
“Failed!” appear, retry the file getting.
ur
it
(Cancel Exit) button
To cancel the getting of the configuration data from the unit
to the PC, click on this button.
y&
(OK) button
To get the configuration data from the unit to the PC, click
on this button.
● How to Display
To display this window, click on the
(Tour Sequence)
button in the main window (p. 65). Or click on the
(Tour Sequence) button in the Group Sequence window.
● Parameters
Cam
Selects the operating camera in each step.
The camera is selectable from Camera 1 to 16. After selecting Camera 1 to 16 for Cam, select the time for Dwell. To
invalidate a step, select "--" for both of Cam and Dwell.
Preset
Selects the preset position of the operating camera.
The preset position is selectable from Preset 1 to 64.
Note: Refer to p. 93 Program Preset Position for details of
how to program preset positions.
Dwell
Selects the dwell time of the operating camera.
The dwell time is selectable from 1 to 30 seconds (by a
second). Set "--" for Dwell when you have selected "--" for
Cam.
68
■ Group Sequence
(DELETE) button
Deletes the configuration of all the steps of the selected
tour sequence.
This window configures the parameters of group
sequences.
Each group sequence has up to 4 tour sequences which
are assigned to the monitors.
(COPY) button
Copies the configuration of all the steps of the selected tour
sequence to the another tour.
(PASTE) button
Pastes the cut or copied configuration to another tour
sequence.
(Save Exit) button
Saves the configuration and closes the Tour Sequence window.
Fi
re
(Cancel Exit) button
Cancels the configuration and closes the Tour Sequence
window.
y&
● How to Display
(Group
ur
it
To display this window, click on the
Sequence) button in the main window (p. 65).
● Parameters
In
te
llig
en
tS
ec
Mon 1 - Mon 4
Selects the tour sequence displayed on each monitor.
69
(Tour Sequence) button
Displays the Tour Sequence window for the tour sequence
configuration.
(Save Exit) button
Saves the configuration and closes the Group Sequence
window.
(Cancel Exit) button
Cancels the configuration and closes the Group Sequence
window.
Note: The tour sequences with different total step number
and dwell time are not configurable in a group
sequence.
■ Timer Event
Spot Camera: Executes the spot mode according to
the schedule in the Scheduled Mode group. When
you have selected Spot Camera, select the number
of monitor (Mon 1 to 4), camera (Cam 1 to 16) and
preset position (Pre 1 to 64).
This window configures the parameters of timer events: the
schedule (daily, weekly or monthly) and action.
Up to 30 events are configurable.
tour sequence or spot mode is selectable.
(Save Exit) button
Saves the configuration and closes the Timer Event window.
(Cancel Exit) button
Cancels the configuration and closes the Timer Event window.
y&
Fi
re
Note: In order to stop a scheduled event on a monitor, you
need to program another event or manually select
another activity. (For example, you need to select a
camera or run a tour.)
● How to Display
(Timer Event) but-
ur
it
To display this window, click on the
ton in the main window (p. 65).
tS
• Enable
Checking on the box will enable the configuration.
ec
● Parameters
en
• Schedule Mode Group
Check on the desired box for the timer event configuration.
In
te
llig
Daily: To execute the event at a desired time every
day, check on this boxes.
To determine the time, click on the Hour and Minute
boxes.
Weekly: To execute the event at a desired time and
day(s) of the week, check on this box.
To determine the time, click on the Hour and Minute
boxes.
Multiple selection is available for days of the week.
Monthly: To execute the event at a desired time and
day(s) of the month, check on this box.
To determine the time, click on the Hour and Minute
boxes.
• Action Group
Check on the desired action to execute.
Tour Sequence: Configures and executes the tour
sequence according to the schedule in the
Scheduled Mode group. When you have selected
Tour Sequence, select the number of monitor (Mon
1 to 4) and tour (Tour 1 to 16).
70
■ Camera Cleaning
Notes:
• When the camera cleaning is active, cleaning will begin
from CAM 1 in numerical order.
• Surveillance is impossible during the cleaning.
• The cleaning cannot be stopped after it is started.
This window configures the parameters of camera cleaning
function: the schedule (daily, weekly or monthly) and cameras to be cleaned.
■ Daylight Saving Time/Summer Time
Fi
re
This window configures the parameters of daylight saving
time (summer time).
● How to Display
(Camera
y&
To display this window, click on the
Cleaning) button in the main window (p. 65).
ur
it
● Parameters
ec
• Camera Auto Cleaning
Checking on the box will enable the configuration.
tS
• Schedule Mode Group
Check on the desired box for the auto cleaning configuration.
In
te
llig
en
Daily: To execute the cleaning at a desired time every
day, check on this box.
To determine the time, click on the Hour and Minute
boxes.
Weekly: To execute the cleaning at a desired time and
day(s) of the week, check on this box.
To determine the time, click on the Hour and Minute
boxes.
Multiple selection is available for days of the week.
Monthly: To execute the cleaning at a desired time and
day of the month, check on this box.
To determine the time, click on the Hour and Minute
boxes.
• Auto Cleaning Camera
Check on the desired camera to execute the cleaning.
(Save Exit) button
Saves the configuration and closes the Camera Cleaning
window.
(Cancel Exit) button
Cancels the configuration and closes the Camera Cleaning
window.
71
● How to Display
To display this window, click on the
Time) button in the main window (p. 65).
(Daylight Saving
● Parameters
• Enable
Checking on the box will enable the configuration.
• Date Group
1. Select the start date of the daylight saving time in the
Start drop-down menu.
2. Select the end date of the daylight saving time in the
End drop-down menu. Select a later date than the Start
date. When selecting an earlier date, a message will
appear.
Note: When clicking on the C button beside a drop-down
menu, a calendar will pop up. To determine the start
and end dates, click on the desired date on the calendar. To go to the next or previous month, click on the
[A] or [B] button and select the dates when the daylight saving time starts and ends.
■ Alarm Mode
This window configures the operation parameters when an
alarm signal is input: an alarm mode, auto reset time and
alarm input.
(Save Exit) button:
Saves the configuration and closes the Daylight Saving
Time window.
Fi
re
(Cancel Exit) button:
Cancels the configuration and closes the Daylight Saving
Time window.
● How to Display
(Alarm Mode) but-
y&
To display this window, click on the
ton in the main window (p. 65).
● Parameters
In
te
llig
en
tS
ec
ur
it
• Alarm Mode
Checking on the box of the desired alarm mode.
OFF: The system operation does not change into any
other mode.
Sequence Mode: Camera images are displayed on the
monitor in either the spot mode or tour sequence.
When more than one alarm are input, the image
associated to each alarm is displayed in the
sequence mode.
Note: Click on the Dwell drop-down menu to select
the dwell time.
Hold Mode: Camera images are displayed on the monitor in either the spot mode or tour sequence. Even
more than one alarm are input, the image associated to the initial alarm is continuously displayed.
Notes:
• The alarm mode is activated when alarm input signals
are assigned to the same monitor through 420 ALARM
EVENT or the Alarm Event (refer to p. 56 or p. 74) window.
• While alarm is activated, you cannot operate the functions related to the multiplexer board.
• Alarm Input Group
Select the alarm input to be accepted. Multiple Selection is
available.
Camera
This stands for that an alarm input is accepted via the
CAMERA IN connectors or the RS-485 ports.
72
ON: The alarm-associated sequence/spot image is displayed on a monitor, and alarm recording will start
(if a recorder is connected to the unit).
ON: The alarm-associated sequence/spot image is displayed on a monitor, and alarm recording will start
(if a recorder is connected to the unit.)
REC ONLY: Only an alarm recording will start and
monitors will keep displaying the current
sequence/spot images.
Note: You cannot recover alarm-related operations
from system controllers when REC ONLY is
selected.
REC ONLY: Only an alarm recording will start and
monitors will keep displaying the current
sequence/spot images.
Note: You cannot recover alarm-related operations
from system controllers when REC ONLY is
selected.
OFF: An alarm input is accepted neither via the CAMERA IN connectors nor the RS-485 ports.
The factory default setting is OFF.
OFF: An alarm input is not accepted by the motion
detector.
Alarm Port
This stands for that an alarm input is accepted via the
ALARM port (25-pin D-sub connector) at the rear panel.
The factory default setting is OFF.
Note: MUX MOTION DET is configurable only when Yes
is selected in the Recorder (refer to p. 66) window.
Fi
re
ON: The alarm-associated sequence/spot image is displayed on a monitor, and alarm recording will start
(if a recorder is connected to the unit).
Sensitivity: When you click this button, the Sensitivity window will appear.
REC ONLY: Only an alarm recording will start and
monitors will keep displaying the current
sequence/spot images.
Note: You cannot recover alarm-related operations
from system controllers when REC ONLY is
selected.
y&
ur
it
ec
OFF: An alarm input is not accepted via the ALARM
port.
Sensitivity
When you press this button, the Sensitivity window will
appear. In this window, you can configure the sensitivity
level of the multiplexer motion detector on each camera
channel.
tS
The factory default setting is ON.
en
Serial Port
This stands for that an alarm input is accepted via the
SERIAL port.
llig
ON: The alarm-associated sequence/spot image is displayed on a monitor, and alarm recording will start
(if a recorder is connected to the unit).
In
te
REC ONLY: Only an alarm recording will start and
monitors will keep displaying the current
sequence/spot images.
Note: You cannot recover alarm-related operations
from system controllers when REC ONLY is
selected.
OFF: An alarm input is not accepted via the SERIAL
port.
The factory default setting is ON.
MUX MOTION DET ON: This stands for that the unit’s
motion detector is activated. When a camera
detects the brightness-level change and transmit an
alarm signal, the alarm-associated sequence/spot
image is displayed on a monitor, and alarm recording will start (if a recorder is connected to the unit).
73
OFF: The motion detector is not activated on the camera channel.
LOW: The sensitivity level is low.
MID: The sensitivity level is medium.
HIGH: The sensitivity level is high.
The factory default setting of all the channels is LOW.
• Alarm Reset Time
Select the time to reset the alarm input.
The selectable time: OFF (not resetting the alarm), 10, 20,
30, 40, 50, 60, 120 or 180 (seconds)
The factory default setting is 30 sec.
(Save Exit) button
Saves the configuration and closes the Alarm Mode window.
Notes:
• If having selected a tour sequence for a monitor, another tour number or spot camera will not be available
when selecting the monitor for another alarm event.
That will result in an error.
• In the factory default setting, Tour 1 to 4 is selectable.
To select Tour 5 to 16, you need to configure the tour
sequences in the Tour Sequence window. (Refer to p.
68.)
(Cancel Exit) button
Cancels the configuration and closes the Alarm Mode window.
(Save Exit) button
Saves the configuration and closes the Alarm Event window.
(Cancel Exit) button
Cancels the configuration and closes the Alarm Event window.
Fi
re
■ Alarm Event
This window configures the details of operation parameters
when an alarm signal is input: the monitor and mode to display the alarm image, and the preset position of the camera. Up to 16 alarm inputs are configurable.
■ Alarm Port
● How to Display
(Alarm Event) but-
● Parameters
In
te
To display this window, click on the
ton in the main window (p. 65).
llig
en
tS
ec
ur
it
y&
This window configures the parameters of alarm inputs.
Mon (Monitor)
Select the monitor to display the alarm image.
Spot/Tour
Select the spot camera number or the tour sequence number.
Cam 1 to 16: To display a spot picture, select a camera
number.
Tour 1 to 16: To execute a tour sequence, select a tour
number.
Pre (Preset Position Number)
Select the preset position of the camera when selecting the
spot camera number in Spot/Tour. Position 1 to 64 is selectable for Pre. When the camera is not equipped with the
preset position function, select "--".
74
● How to Display
To display this window, click on the
ton in the main window (p. 65).
(Alarm Port) but-
● Parameters
• Alarm Port Group
Select the desired alarm input parameter in each alarm
port's drop-down menu.
N.O. : Normally Open
N.C. : Normally Close
• Time Adjust Box
Select the alarm port to assign to the time adjustment.
When not assign any port to time adjustment, select None.
(Save Exit) button
Saves the configuration and closes the Alarm Input window.
(Cancel Exit) button
Cancels the configuration and closes the Alarm Input window.
■ Operator Registration
• Camera Access Group
This group configures the camera operation coverage of
each operator.
Click on each camera's checkboxes and determine the
available operation.
1 (View & Control): The operator can display the camera image on the monitor and control panning/tilting.
2 (View Only): The operator can display the camera
image on the monitor, but cannot control the panning/tilting.
3 (Prohibited): The operator can neither display the
camera image on the monitor nor control the panning/tilting.
This window configures the parameters of each operator:
the ID, password, level, priority and camera access.
Note: Before configuring this window, check on the
restrict level of each operation in the Level Table
window.
Fi
re
(Add) button
Adds a new operator to WJ-SX150 Administrator Console.
(Edit) button
The registered parameters become editable by clicking on
this button after selecting the operator number.
● How to Display
(Operator
tS
● Parameters
In
te
llig
en
• Operator Number
This box displays a list of registered operators.
1-6: These are operator numbers who are registered as
the factory default setting. Operator Number 1 cannot be deleted.
Timer: This operator is used for the priority change of a
timer event. When the timer event's priority is higher
than that of an operator, the event is valid. When an
operator's priority is higher than that of a timer
event, the event is invalid. This operator cannot be
deleted.
• Add Operator Number
This drop-down menu is used for the new operator number
selection.
• Operator Group
This group configures each operator's password, level and
priority.
ID: Enter an operator's ID. From 1 to 99999 are available.
Password: Enter a password. From 1 to 99999 are
available.
Level: Select 1, 2 or 3.
Priority: Select the operator's priority from 1 (highest)
to 16 (lowest).
75
(OK) button
Saves the configuration
Registration window.
ec
To display this window, click on the
Registration) button in the main window (p. 65).
ur
it
y&
(Delete) button
Deletes an operator from WJ-SX150 Administrator Console
after you select the operator.
and
closes
the
Operator
■ Level Table
■ Monitor Selection
This window configures the restrict level of each operation.
The restrict level is classified in Level 1, 2, and 3.
This window determines whether a system controller or PC
can select a monitor.
Fi
re
● How to Display
To display this window, click on the
Selection) button in the main window (p. 65).
● How to Display
● Parameters
(Level Table) but-
y&
To display this window, click on the
ton in the main window (p. 65).
(Monitor
● Parameters
(Save Exit) button
Saves the configuration and closes the Monitor Select window.
ec
• Permission
Click on each checkbox to classify the following operations
by three levels.
ur
it
Select OK to permit each controller and the PC to control
Monitor 1 to 4.
Select NG to restrict each controller and the PC to control
Monitor 1 to 4.
In
te
llig
en
tS
SX150 Setup: Setting up this matrix switcher system
Camera Setup: Setting up the cameras
Alarm History Display: Displaying the alarm history
Video Loss History Display: Displaying the video loss
history
System Status Display: Displaying the system status
Single Alarm Reset: Resetting an alarm
All Alarm Reset: Resetting all the alarms
Alarm Suspend: Suspending an alarm
Camera View: Selecting a camera
Call Sequence: Activating a tour or group sequence
Program Preset Position: Registering a camera's preset position
OSD Control: Displaying SETUP MENU
Camera Control: Controlling a camera
Recorder Control: Controlling the recorder
Recorder Setup: Displaying the recorder's setup menu
(Save Exit) button:
Saves the configuration and closes the Level Table window.
(EXIT) button
Cancels the configuration and closes the Level Table window.
76
(Cancel Exit) button
Cancels the configuration and closes the Monitor Select
window.
■ Auto Login/Logout (Auto Log-in/Logout)
■ Time & Date
This window configures the unit's clock display pattern. The
unit's clock time is also adjustable.
This window configures the auto log-in/log-out parameter of
each data port.
An operator is selectable for auto log-in function.
This picture is the example for U. S. model.
Out of the U. S., the display pattern is Date/Month/Year.
Fi
re
● How to Display
The log-out time is selectable for auto log-out function.
To display this window, click on the
the main window (p. 65).
● How to Display
● Parameters
● Parameters
• Display Format
The current date & time is displayed.
Click on the drop-down menu and select the display pattern format.
The date display is selectable from 5 patterns.
The time display is selectable from 2 patterns (12H or 24H).
The following are the display patterns:
DD/MM/YYYY…21/08/2001
MM/DD/YYYY…08/21/2001
DD/Mmm/YYYY…21/Aug/2001
YYYY/MM/DD…2001/08/21
Mmm/DD/YYYY…Aug/21/2001
The factory default setting is Mmm/DD/YYYY pattern.
(Out of the U. S., the factory default setting is
DD/MM/YYY.)
tS
ec
• Auto Login Box
Click on the checkboxes DATA 1 to 4 to select an operator
for auto log-in. Then, select an operator ID. It will be the
log-in ID of the system controller connected to the data
port.
y&
(Auto
ur
it
To display this window, click on the
Login/Logout) button in the main window (p. 65).
(Clock) button in
llig
en
• Auto Logout Box
Click on the checkbox of the data port connecting the system controller for auto log-out. Then, select the elapsed
time for auto log-out.
In
te
(Save Exit) button
Saves the configuration and closes the Auto Login/Logout
window.
(Cancel Exit) button
Cancels the configuration
Login/Logout window.
and
closes
the
Auto
Notes:
• Both of auto log-in and auto log-out cannot be assigned
to the same data port.
Either of them is selectable.
• Data ports are usable for RS-485 camera connections.
(Refer to p. 38.) However, when an RS-485 camera is
connected to a data port, its port number is displayed
in gray and auto log-in/log-out is not assignable. (Refer
to p. 81 for details on data port setting.)
• When PSD is set for DATA 4 in the Data Port (refer to p.
81) window, its port number is displayed in gray and
auto log-in/log-out is not assignable. (The factory
default setting of the DATA 4 is PSD.)
77
(Clock) button
Displays the Clock window.
(Save Exit) button
Saves the configuration and closes the Time & Date, window.
(Cancel Exit) button
Cancels the configuration and closes the Clock Disp window.
Note: The display pattern will be updated when the setting
file has been put from the PC to the unit.
● Clock
■ Cable Compensation/VD2/DATA
This window configures the unit's clock.
The pattern of the Time & Date box depends on the setting
through the Time & Date window.
This window configures the following parameters of each
camera: the cable length for transmission loss compensation and whether to send the VD2 timing pulse or control
data with the camera output signals.
This picture is the example for U. S. model.
• How to display
To display this window, click on the
the Time & Date window.
Fi
re
(Clock) button in
• Parameters
Time & Date Box: To adjust the clock, click on the ▼ or
▲ buttons of Year, Month, Day, Hour and/or Minute
y&
● Parameters
ec
(Cancel Exit) button: Cancels the configuration
and closes the Clock window.
To display this window, click on the
(Cable
Compensation/VD2) button in the main window (p. 65).
ur
it
(Put to SX150) button: Changes the unit's
clock time into the one which has been configured
in this window.
● How to Display
In
te
llig
en
tS
Note: The clock display pattern is not updated by clicking the
(Put to SX150) button in this window. The setup file update will be necessary. (Refer
to p. 67 Put a File to SX150.)
78
Cable Comp: Select the cable length for each camera.
S: Less than 400 m (1 300 ft)
M: 400 m (1 300 ft) to 700 m (2 300 ft)
L: 700 m (2 300 ft) to 900 m (3 000 ft)
VD2: To send the VD2 timing pulse with the camera
output signal, select ON.
Not send the VD2 timing pulse with the camera output signal, select OFF.
DATA: To send the control data with the camera output
signal, select ON.
Not send the control data with the camera output
signal, select OFF.
■ Camera Title
● Edit Camera Title
1. Click on the tab of the desired camera to edit its camera title. The cursor blinks at the first block in the text
box.
Note: When the desired camera's tab does not appear,
click on the buttons A or B beside the tabs.
This window configures the title for each camera.
Up to 20 characters (camera title + alphanumeric characters) are available for the title.
WJ-SX150 Administrator Console has the following built-in
characters:
ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrs
tuvwxyz0123456789!"#$%&'()*+,–./:;
,=/?•_ÄÜÖÆÑÂØäüöæñâøÁÇÉÌÒÙßàáâçèéêëìíîïòóôùúû
2. Click on the <– or –> button to move the cursor to the
desired position.
3. Click on the desired character button in the Fixed Font
or User Font box. The character will be entered in the
text box.
In addition, symbols, special characters and original characters are editable in the bitmap font.
4. Repeat steps 2 and 3 to enter the camera title.
5. After the entry, click on the
The camera title will be saved.
(Save Exit) button.
Fi
re
Camera title
input area
y&
To Enter a Space in the Text Box
1. Click on the <– or –> button to move the cursor to the
desired position.
2. Click on the SPACE button.
ur
it
ec
● How to Display
en
● Parameters
(Camera Title)
tS
To display this window, click on the
button in the main window (p. 65).
te
llig
• Fixed Font Box
The fixed-font characters are displayed here.
SPACE: To make a space in the text-box area, click on
this button.
In
• User Font Box
The character displayed here is editable by users.
Edit Font: To display the Edit Font window, click on this
button.
• Insert / Revise Radio button
To insert a character in the text-box area, click on the Insert
button. To revise the character there, click on the Revise
button.
(Save Exit) button
Saves the configuration and closes the Camera Title window.
Note: Be sure to click on this button after editing user font
characters. Otherwise, the edited characters will be
canceled.
(Cancel Exit) button
Cancels the configuration and closes the Camera Title window.
79
To Delete a Character in the Text Box
1. Click on the Revise button.
2. Click on the <– or –> button and move the cursor to the
character for deletion.
3. Click on the DEL button.
The character will be deleted from the text box.
To Revise a Character in the Text Box
1. Click on the Revise button.
2. Click on the <– or –> button and move the cursor to the
character for revision.
3. Click on the desired character.
The character will be entered in the text box.
To Insert a Character in the Text Box
1. Click on the Insert button.
2. Click on the <– or –> button and move the cursor to the
block to enter a character.
3. Click on the SPACE button to enter a space.
4. Click on the Revise button.
5. Click on the desired character in the text box.
The character will be inserted in the text box.
To Cancel the Entry
Click on the
(Cancel Exit) button.
The entry will be canceled and the Camera Title window will
close.
● Edit Font Window
Note: The new character has not been saved in the
configuration data at this point. After closing the
Edit Font window, be sure to return to the Camera
Title window and click on the
(Save Exit) button.
The Window Soon after Opening
• To Copy a Character
1. Click on the desired character in the User Font box.
2. Click on the Copy button.
3. Click on the blank in the User Font box to copy the
character.
4. Click the Paste button.
• To Delete a Character
1. Click on the desired character in the User Font box.
2. Click on the Delete button.
3. Click on the Save –> button.
ec
• How to Display
To display this window, click on the Edit Font button in the
Camera title window.
ur
it
y&
Fi
re
The Window during the Edit
In
te
llig
en
tS
• Parameters
User Font Box: The registered user font characters are
displayed here. Up to 320 characters (20 for each
camera x 16) are registerable.
Edit Font Box: The selected user font characters are
displayed here in 12 x 13 dots.
(Delete) button: Deletes an user font character.
1. Click on the desired character in the User Font
box.
2. Click on the Delete button.
(Copy) button /
(Past) button: A user font
character can be copied by clicking these buttons.
Save –> button: The edited or deleted character is registered in the User Font box.
(OK) button: Closes the Edit Font window.
• To Edit a User Font Character
1. Click on the desired characters in the User Font box.
When making a new character, click on a blank.
The selected user font character are displayed here in
12 x 13 dots.
2. Click on
or
to make a character.
and
will appear alternately by clicking.
will change into black after the character is registered in the User Font box.
3. When finishing the edit, click on the Save –> button.
The edited character will be registered in the User Font
box.
80
■ Data Port
Alarm Data: Select the desired time to accept an
alarm input signal. OFF, 0, 1 or 5 sec is available.
The factory default setting is 1 sec.
Wait Time: Select the desired wait time to transmit
an alarm output signal. OFF, 100msec, 200m
sec, 400m sec or 1 sec is available.
The factory default setting is OFF.
Group Address: This parameter is only for confirmation. Leave as it is.
This window configures the parameters of each data port
(RS485, DATA 1 to 4 and DATA HDR port): the protocol, the
baud rate (communication speed), and the connected
cameras.
• Fixed Common Parameter Group
The data bit (8 bit), parity (none), and stop bit (1 bit) are
displayed. These parameters are fixed.
Fi
re
(Save Exit) button
Saves the configuration and closes the Data Port window.
(Cancel Exit) button
Cancels the configuration and closes the Data Port window.
(Data Port) button
● Parameters
In
te
llig
en
tS
ec
• RS-485 Port Group
Protocol: Select RS485 when an RS-485 camera is
connected to the data port.
Select CU360C when the system controller is connected to the data port.
Select PSD when the system controller is connected
to the DATA 4 port via the PS·Data protocol.
PS·Data mode will appear in the window.
Note: The baud rate of DATA HDR is the same as
that of PSD. When you select PSD for DATA 4,
DATA HDR and its baud rate are displayed in
gray and not configurable. When you select
CU360C for DATA 4, DATA HDR and its baud
rate are configurable.
Baud Rate: Select the desired baud rate (communication speed). 4800, 9600 or 19200 bps is selectable.
RS485 Camera Daisy (RS-485 Camera Daisy): Select
the number(s) of the camera(s) connected to the
RS-485 daisy chain.
Data 1 to 3 are connectable to either of cameras
and system controllers.
When connecting cameras to these ports, select the
connected camera number(s).
PS·Data mode: This stands for the PS·Data parameters
of the DATA 4 port.
Logout Time: Select the desired operable time
before logout. OFF,10, 20, 30, 60, 90 or 120 sec
is available.
The factory default setting is 30 sec.
ur
it
To display this window, click on the
in the main window (p. 65).
y&
● How to Display
81
■ Multiplexer Mode
ON: The drop-down menu becomes also active so that
you can select the desired monitor among MON 1
to 4. For example, when you select MON 1, other
operators, whose priority is lower than you, cannot
view the monitor (secret view).
OFF: Secret view function is unavailable.
The factory default setting is OFF.
Sequence Mode: Select the sequence type by clicking
on the radio button.
Quad: Multiplexer sequence is activated. The monitor
display will be changed as 4A → 4B → 4C → 4D.
3+1: Images are displayed in 4 multiscreens, and the
images of Camera 4 to 16 are displayed in the
sequence mode, at the right bottom of the monitor.
The images of Camera 1 to 3 are fixed. (Refer to the
left-side illustration in p. 19.)
8+1: Images are displayed in 9 multiscreens, and the
images of Camera 9 to 16 are displayed in the
sequence mode, at the right bottom of the monitor.
The images of Camera 1 to 8 are fixed. (Refer to the
right-side illustration in p. 19.)
● How to Display
Fi
re
Note: This window can be displayed only when “Yes” is
selected in the Recorder window. (Refer to p. 66.)
● Parameters
tS
The factory default setting is ON.
In
te
llig
en
Border Color: Select the desired setting by clicking on
the drop-down menu. This setting will determine the
color of the border which separates each multiscreen segment.
WHITE: The border will be displayed in white.
GRAY: The border will be displayed in gray.
BLACK: The border will be displayed in black.
OFF: No border will be displayed.
The factory default setting is WHITE.
Quad Shift: Select the desired setting by clicking on
the drop-down menu.
ON: Camera images are displayed in 4 multiscreen
segments (quad) and switched as follows:
4A = Page 1 of the quad (Camera 1, 2, 3 and 4)
4B = Page 2 of the quad (Camera 5, 6, 7 and 8)
4C = Page 3 of the quad (Camera 9, 10, 11 and
12)
4D = Page 4 of the quad (Camera 13, 14, 15 and
16)
OFF: Quad is unavailable.
The factory default setting is OFF.
Secret View: Select the desired setting by clicking on
the drop-down menu.
82
The factory default setting is Quad.
Dwell: The dwell time of the selected sequence mode
is selectable. 2S to 30S is available.
The factory default setting is 2S.
ec
• Multi Monitor Out Group
Still Display: Select the desired setting by clicking on
the drop-down menu.
ON: Still picture is available during the multiscreen display.
OFF: Still picture is not available during the multiscreen
display.
y&
(Multiplexer
ur
it
To display this window, click on the
Mode) button in the main window (p. 65.)
• REC OUT Group
Title Display: Select the desired setting by clicking on
the drop-down menu.
ON: The camera title is displayed on the recorded
image.
OFF: The camera title is not displayed on the recorded
image.
The factory default setting is ON.
Clock Display: Select the desired setting by clicking on
the drop-down menu.
ON: The date and time are displayed on the recorded
image.
OFF: The date and time are not displayed on the
recorded image.
The factory default setting is ON.
Normal Group
REC Mode: Select the desired setting by clicking on
the radio button.
EXT: Select this to gen-lock the unit during the normal
recording.
INT: Select this if the asynchronous unit is connected to
the unit. When it is activated, the drop-down menu
becomes also active so that you can select the
desired normal recording rate. 002, 004 to 255
(field) are selectable.
The factory default setting is EXT.
Alarm Group
REC Mode: Select the desired setting by clicking on
the radio button.
EXT: Select this to gen-lock the unit during the alarm
recording.
INT: Select this if the asynchronous unit is connected to
the unit. When it is activated, the drop-down menu
becomes also active so that you can select the
desired normal recording rate. 002, 004 to 128
(field) are selectable.
(Save Exit) button
Saves the configuration and closes the Multiplexer Mode
window.
(Cancel Exit) button
Cancels the configuration and closes the Multiplexer Mode
window.
● Mux Alarm Group
y&
ec
The factory default setting is OFF.
This is a submenu of the Multiplexer window. In this window, up to 4 cameras are given recording priority for each
alarm input.
• Click a drop-down menu to assign the camera numbers
(1 to 16) to each alarm input (ALM 1 to 16). The factory
default setting is same as the illustration.
• To configure ALM 9 to 16, click on the ALM 9 – 16 tab.
ur
it
DYNAMIC REC: Select the desired setting by clicking
on the drop-down menu.
ALM-PRI: Select this to give recording priority to the
camera channel with the alarm input.
ALM-ONLY: Select this to record the images from the
alarm-associated camera channel.
GROUP: Select this to give recording priority to a group
of up to 4 camera channels associated to the alarm
input. When you select this, the Group Setting button becomes active. By pressing the button, the
Mux Alarm Group window will be displayed so that
you can configure the ALM 1 to 16 parameters.
(Refer to Mux Alarm Group.)
OFF: Select this to deactivate the alarm priority mode.
Fi
re
The factory default setting is EXT.
The factory default setting is ON.
llig
en
tS
• System Group
Camera SW Loss: Select the desired setting by clicking on the drop-down menu.
ON: “CAM SW LOSS” will blink on the associated monitor when loss of the camera switching pulse is
detected.
OFF: “CAM SW LOSS will not appear on the monitor.
In
te
Dummy Black: Select the desired setting by clicking
on the drop-down menu.
ON: The black image will be displayed for a camera
channel that is not connected to the camera.
OFF: The camera channel will be skipped in the
sequence/spot mode.
The factory default setting is ON.
83
(Save Exit) button
Saves the configuration and closes the FS Board Alarm
Group window.
(Cancel Exit) button
Cancels the configuration and closes the FS Board Alarm
Group window.
■ Select Setup Data File
● Multiplexer Title
The setup file is selectable by pressing this button.
For example, this function will be used when making a new
setup file with the factory default setting or configuring an
existing setup file.
Refer to the operating instructions of Windows® for details
of how to copy a data.
● How to Display
To display this window, click on the
in the main window (p. 65).
(File Open) button
● Parameters
● How to Display
(Multiplexer Title)
Fi
re
To display this window, click on the
button in the main window (p. 65.)
The location, name and type of the setup file appear in this
window.
File Name Input Area: Displays the selected file's
name. A new file (a setup file with the factory default
setting) will be made when entering a new name.
Open button: Opens the selected file.
Cancel button: Cancels the operation and closes the
Select Setup Data File dialog box.
● How to Display
y&
Note: This window can be displayed only when "Yes" is
selected in the Recorder window. (Refer to p. 66.)
tS
ec
The factory default settings are same as the illustration.
(The text box covered with the cursor is “C”.)
To edit the desired camera’s title, click on the associated
button (Cam 1 to Cam 16).
The subsequent editing procedure is the same as Camera
Title. (Refer to p.79.)
ur
it
● Parameters
llig
en
Notes:
The characters available here are the following:
ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrs
t u v w x y z 0 1 2 3 4 5 6 7 8 9 ! " # $ % & ' ( ) * + , ./:;¨=Æ?oÄÜÖÆÑÃØäüöæñãø
In
te
• Up to 8 alphanumeric characters are available for the
multiplexer board camera title.
• You cannot edit a user font character.
(Save Exit) button
Saves the configuration and closes the Multiplexer Board
Camera Title window.
(Cancel Exit) button
Cancels the configuration and closes the Multiplexer Board
Camera Title window.
84
■ Account Manager
(Add Account) button
To register a new operator, click on this button. The
Registration window will appear.
This window configures the parameters of the operators
who can control WJ-SX150 Administrator Console: the registration, edit and deletion of an operator.
(EDIT) button: To configure the operator information,
click on this button.
The window soon after opening
(DELETE) button
To delete the operator selected in the Accounts group,
click on this button.
(Save Exit) button
Saves the configuration and closes the Account Manager
window.
Fi
re
(Cancel Exit) button
Cancels the configuration and closes the Account Manager
window.
The window during the edit
● Edit Account Manager
tS
ec
ur
it
y&
Add a Registration Operator
1. Click on the
button.
2. Enter the name in the Name box and the password in
the Password box.
Name: Up to 20 alphanumeric characters
Password: Up to 20 alphanumeric characters
3. Click on the ▼ button to select the level.
4. Click on the
(Save exit) button.
The configuration will be saved and the Registration
window will close.
To cancel the configuration, click on the
(Cancel
exit) button.
Note: You can register up to 16 accounts (operators).
en
● How to Display
(Account
llig
To display this window, click on the
Manager) button in the main window (p. 65).
● Parameters
In
te
Note: Register at least one operator with level 1. If there is
no level 1 operator, the configuration of WJ-SX150
Administrator Console will become impossible.
• Accounts Group
The registered operator names appears. To display the
operator information in the Account Record group, click on
the name.
You can configure up to 16 account records.
• Account Record Group
Name: The operator name is displayed.
Password: The password is displayed as "*****". The
entered password is displayed here during the edit.
Level: Select the operator level.
(OK) button
Closes the Account Manager window.
85
Edit a Registration Operator
1. Click on the registration operator's name in the
Accounts group.
2. Click on the
(EDIT) button.
3. Edit the desired parameters.
4. Click on the
(Save exit) button.
The configuration will be saved and the Registration
window will close.
To cancel the configuration, click on the
(Cancel
exit) button.
Delete a Registration Operator
1. Click on the registration operator's name in the
Accounts group.
2. Click on the
(Delete) button.
3. Click on the
(Save exit) button.
Note: If deleting all level 1 operators, the configuration of
WJ-SX150 Administrator Console will become impossible.
■ Communication Port
This window configures the PC's usable communication
port number and its baud rate (communication speed).
● How to Display
(Communication
Fi
re
To display this window, click on the
port) button in the main window (p. 65).
ec
The factory default setting is 38400 bps.
ur
it
• Parameter Group
Com: Select the PC's communication port for the connection to the unit.
Baud Rate: Select the desired baud rate (communication speed). 4800, 9600, 19200 or 38400 bps is
selectable.
y&
● Parameters
en
tS
• Fixed Parameter Group
The data bit (8 bit), parity (none), and stop bit (1 bit) are
displayed.
Note: These parameters are fixed.
llig
(Save Exit) button
Saves the configuration and closes the Communication Port
window.
In
te
(Cancel Exit) button
Cancels the configuration and closes the Communication
Port window.
86
Fi
re
In
te
llig
en
tS
ec
ur
it
y&
OPERATING PROCEDURES
(TERMINAL MODE)
87
LOG-IN AND LOG-OUT
Before starting the following procedures, all system components must be turned on.
The following procedures are applicable when the system
controller is connected to the unit.
■ Log-in
Note: If an operator ID or password error occurs, the
PROHIBITED indicator on the controller will blink
and "NO ACC" will blink on the LED display for
about 3 seconds. Then "NO USER" appears on the
LED display. Return to step 3 and select your operator ID.
This operation is skipped when the auto log-in is set to ON.
(Refer to p. 89.)
y&
ur
it
Note: If the auto log-in is set to ON, any operator can login
automatically. After the controller is turned on, "AUTO"
appears on the LED display for approximately 2 seconds, then "READY" automatically appears.
CAM ID
EVENT
AUX1 ON
llig
T&D
en
tS
ec
3. To select your registered operator ID number (1 to 16,
up to 2 digits), press the numeric buttons, then press
the CAM (SET) button.
The underline appears on the LED display of the controller.
The factory default setting is 150.
Fi
re
1. Turn on the power switches of all system components.
The OPERATE indicator will light up.
2. To turn on the power of the system controller, connect
the AC adapter to the AC outlet.
The LINK indicator lights up and "NO USER" appears
on the LED display of the system controller.
AUX1 OFF
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
In
te
STILL
MON STATUS
SEQUENCE
DEF OFF
MON (ESC)
MON LOCK
DEF ON
CAM (SET)
MULTI SCREEN SEL
WIPER
4. To select your registered password (up to 5 digits),
press the numeric buttons, then press the CAM (SET)
button.
The factory default setting is 150.
If the operator ID and password are correct, "READY"
will appear on the LED display.
88
■ Log-out
■ Auto Log-in
This operation is skipped when the auto log-out is set to
ON.
This function is used when an operator leaves the controller
or no longer requires access to the system.
If the auto log-in is set to ON, any operator can login automatically. After the controller is turned on, "AUTO" appears
on the LED display for approximately 2 seconds, then
"READY" automatically appears.
Auto log-in is configurable through WJ-SX150 Administrator
Console. (Refer to p. 77 Auto Login/Logout.)
1. To logout from the system press the CLEAR button
while holding down the SHIFT button.
"NO USER" appears on the LED display of the controller.
■ Auto Log-out
NEXT
T&D
CAM ID
EVENT
STILL
AUX1 OFF
AUX1 ON
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
DEF ON
If the auto log-out is set to ON and no operation takes place
for a specific time, any operator can logout automatically.
"NO USER" automatically appears on the LED display.
Fi
re
TOUR SEQ
CALL
PRESET
PROGRAM
PRESET
AUTO PAN
MON (ESC)
SHIFT
MON LOCK
MULTI SCREEN SEL
CAM (SET)
CLEAR
WIPER
LOG OUT
y&
PAUSE
CAM FUNC
In
te
llig
en
tS
ec
Notes:
• If you want to save the power consumption, disconnect the PC plug from the controller, and remove
the AC adapter from the AC outlet.
• If the auto log-out is set to ON, any operator can
logout automatically if no operation takes place for
a specific time. "NO USER" automatically appears
on the LED display.
• The time to logout is configurable through WJSX150 Administrator Console. (Refer to p. 77 Auto
Login/Logout.)
Auto log-out and the time to logout are configurable
through WJ-SX150 Administrator Console. (Refer to p. 77
Auto Login/ Logout.)
ur
it
PAUSE
89
MONITOR SELECTION AND CAMERA SELECTION
■ Priority Lock
After the log-in procedure, the following operations are
available to control the system.
The operation begins with selecting a monitor, then the
selected camera appears the active monitor.
● Applying Priority Lock
1. Select the desired monitor. (Refer to Monitor Selection).
■ Monitor Selection
2. Press the MON (ESC) button while holding down the
SHIFT button to toggle the priority lock mode on and off
on the active monitor.
If the priority lock mode is selected, the monitor number
will inversely appear on the active monitor as shown in
the figure.
1. To select the desired monitor number (1 to 4), press the
numeric button.
2. Press the MON (ESC) button to execute the selection.
The MONITOR indicator on the controller will light up
and the selected monitor number will appear on the
LED display of the controller.
CAM ID
EVENT
STILL
AUX1 OFF
AUX1 ON
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
DEF OFF
MON (ESC)
CAM (SET)
MULTI SCREEN SEL
WIPER
tS
MON LOCK
DEF ON
ec
SEQUENCE
ur
it
T&D
y&
Fi
re
Note: This function will prevent operators with lower priority
from gaining control of a monitor.
However, higher or equal priority operators may still
gain control of the monitor.
llig
en
3. If the selected monitor number is not valid, the PROHIBITED indicator lights up and the number on the LED display will blink for approximately 3 seconds.
Return to step 1 and select a new monitor number.
In
te
Note: The PROHIBITED indicator will blink if an operator with higher priority is controlling the
monitor.Control of the same monitor is denied to an
operator with lower priority.
90
TOUR SEQ
T&D
CAM ID
EVENT
STILL
AUX1 OFF
AUX1 ON
NEXT
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
DEF ON
PAUSE
PAUSE
MON (ESC)
SHIFT
MON LOCK
M04
CAM (SET)
MULTI SCREEN SEL
WIPER
● Releasing Priority Lock
1. Select the desired monitor. (Refer to Monitor Selection.)
2. Press the MON (ESC) button while holding down the
SHIFT button to release the priority lock mode.
The monitor number returns to the normal display on
the active monitor.
■ Camera Selection
1. Select the desired monitor. (Refer to p. 90 Monitor
Selection.)
2. Press the numeric buttons to select the desired camera
number (1 to 16).
3. Press the CAM (SET) button.
The selected camera's image will appear on the active
monitor. The CAMERA indicator will light up and the
selected camera number will appear on the LED display on the controller.
ACK
RESET
SUSPEND
ALL RESET
F2
GROUP SEQ
TOUR SEQ
REW/FF
INDEX
PREV
PAUSE
In
PLAY
te
PAUSE
STOP
STOP
NEXT
STEP
RECORDER
llig
CAM SETUP
en
F1
y&
ur
it
tS
ec
4. If the selected camera number is not valid, the PROHIBITED indicator and the number on the LED display
will blink for about 3 seconds.
Return to step 2 and select a new camera number.
5. To replace the currently selected camera with the next
higher-numbered camera , press the NEXT button.
6. To replace the currently selected camera with the next
lower-numbered camera, press the PREV button.
Fi
re
Note: If you select a wrong number, press the CLEAR
button to clear the input.
OSD
SETUP
SHIFT
Note: The PROHIBITED indicator will light up, if the
camera is selected by an operator with higher priority. Control of the same camera is denied to an
operator with lower priority.
91
CAMERA CONTROL
Moving the zoom wheel controller of WV-CU360CJ can
also adjust the lens zoom.
Buttons and control for cameras or camera site accessories
are located on the right side of the front panel of the system
controller.
Included are zoom control, focus control, iris control, preset
and pan/tilt controls.
Normally, combination cameras equipped with the specific
feature or a WV-RC100 or WV-RC150 Receiver are required
to utilize these functions.
Note: Refer to the cameras' operating instructions whether
to confirm that each function is available.
WIDE
TELE
Zoom wheel controller
4. Press the IRIS CLOSE/OPEN buttons to close/open the
lens iris. The lens iris is adjusted by these buttons to
obtain the proper image exposure.
Fi
re
■ Lens Control
This function is available when specified lens, with motorized zoom/ focus functions, is mounted on the camera, and
the lens selection (DC/VIDEO) on the camera is set to DC.
IRIS
CLOSE
ur
it
■ Pan/Tilt Control
● Manual Operation
tS
FOCUS
FAR
NEAR
To reset to the factory default setting, press these buttons simultaneously.
ec
2. Press the FOCUS NEAR/FAR buttons while watching
the monitor. The lens focus is adjusted to obtain a
sharply focused image.
To set the lens focus automatically, press these buttons
simultaneously.
AUTO IRIS
y&
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
OPEN
en
AUTO FOCUS
2. Move the joystick to move the pan/tilt head towards the
desired direction.
UP
L
In
te
llig
Pressing the top button of WV-CU360CJ can also set
the lens focus automatically.
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
R
DOWN
Top button
3. Press the ZOOM WIDE/TELE buttons while watching the
monitor. The lens iris is adjusted to obtain the desired
image.
Press the TELE button to bring an object optically closer. Press the WIDE button to widen the scene optically.
ZOOM
WIDE
● Auto Panning
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. To activate the auto panning function of the selected
camera, press the AUTO PAN button.
AUTO PAN
TELE
REC
CAM FUNC
3. To cancel the auto panning function, move the joystick.
92
■ Program Preset Position
■ Call Preset Position
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. To move the camera to the position to be preset, move
the joystick and press the lens control buttons.
2. To select the desired preset position number, press the
numeric buttons.
3. To select the desired preset position number, press the
numeric buttons.
4. When you have selected a wrong number, press the
CLEAR button to clear the numeric input.
4. When you have selected a wrong number, press the
CLEAR button to clear the numeric input.
3. Press the CALL PRESET button to move to the preset
position of the selected camera on the active monitor.
NEXT
T&D
CAM ID
STILL
AUX1 OFF
MON STATUS
ALL
EVENT
AUX1 ON
CALL
PRESET
PROGRAM
PRESET
ur
it
TOUR SEQ
y&
Fi
re
4. Press the CALL PRESET button while holding down the
SHIFT button to save a preset position of the selected
camera.
AUTO PAN
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
MON (ESC)
MON LOCK
MULTI SCREEN SEL
DEF ON
CAM (SET)
CLEAR
WIPER
LOG OUT
en
SHIFT
CAM FUNC
ec
PAUSE
AUX2 OFF
tS
PAUSE
EL-ZOOM
In
te
llig
Notes:
• If the entered position number has stored the previous preset position, it will be overwritten by the new
one.
• SETUP MENU
and
WJ-SX150
Administrator
Console can configure each operator's pan/tilt control. (Refer to p. 62 OPERATOR REGISTRATION or
p. 75 Operator Registration.)
93
T&D
CAM ID
EVENT
AUX1 ON
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
CALL
PRESET
PROGRAM
PRESET
AUTO PAN
MON (ESC)
MON LOCK
MULTI SCREEN SEL
CAM FUNC
DEF ON
CAM (SET)
CLEAR
WIPER
LOG OUT
Note: To use the above function, you must set the preset position number for the camera.
CAMERA FUNCTION CONTROL
■ Camera Function (Shortcut Function)
■ Camera Setup
The following function is available only when specified cameras with the camera function feature are used.
This function enables executing camera functions via a
shortcut.
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. Press the F1 button while holding down the SHIFT button.
The CAM SETUP indicator on the controller will light up
and the camera's SETUP MENU will appear on the
active monitor.
ACK
RESET
CAM SETUP
SUSPEND
ALL RESET
F2
GROUP SEQ
TOUR SEQ
REW/FF
INDEX
2. Press the AUTO PAN button while holding down the
SHIFT button.
"F_ _ _ _" will appear on the LED display of the controller as shown in the figure.
PREV
NEXT
T&D
CAM ID
EVENT
AUX1 ON
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
Fi
re
F1
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
CALL
PRESET
PROGRAM
PRESET
STOP
PLAY
PAUSE
MON (ESC)
OSD
CAM FUNC
F1
DEF ON
CAM (SET)
CAM SETUP
CLEAR
ur
it
PAUSE
STOP
y&
AUTO PAN
STEP
RECORDER
F2
SETUP
SHIFT
MON LOCK
MULTI SCREEN SEL
WIPER
LOG OUT
ACK
SUSPEND
ALL RESET
GROUP SEQ
TOUR SEQ
REW/FF
ec
INDEX
In
te
llig
en
tS
3. To select the desired item in the menu, move the joystick to ▼ or ▲. To select the desired parameter (or
mode) in the menu, move the joystick to t or s.
4. To execute the currently highlighted selection and to
enter a submenu of SETUP MENU, press the CAM
(SET) button.
5. To leave from the currently selected menu and to return
to the previous page of the menu, press the MON (ESC)
button.
6. Move the cursor to SPECIAL on the camera’s setup
menu, and press numeric buttons 4 and 6 simultaneously for 2 seconds or more to display the special
menu.
7. Move the cursor to CAMERA RESET on the camera’s
setup menu, and press buttons 4, 5 and 6 simultaneously to reset all the functions to the defaults.
Notes:
• Refer to the operating instructions of the selected
camera for details.
• Move the joystick while holding down the SHIFT
button to move the camera smoothly for presetting
the positions in the camera's SETUP MENU.
8. To close the camera's SETUP MENU, press the F1 button while holding down the SHIFT button.
The CAM SETUP indicator goes off.
94
RESET
PREV
NEXT
T&D
CAM ID
EVENT
AUX1 ON
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
CALL
PRESET
PROGRAM
PRESET
AUTO PAN
STEP
RECORDER
PAUSE
STOP
STOP
PLAY
PAUSE
MON (ESC)
OSD
SETUP
SHIFT
MON LOCK
MULTI SCREEN SEL
CAM FUNC
DEF ON
CAM (SET)
CLEAR
WIPER
LOG OUT
3. Press the numeric buttons to select an assigned function number, then press the CAM (SET) button.
For example, enter 175 for AGC ON.
The selected function will be executed on the active
monitor.
Notes:
• When you select a wrong number, press the CLEAR
button to clear the numeric input.
• Refer to the cameras' operating instructions for
details on available shortcuts.
4. To exit from the mode, press the MON (ESC) button
then press the AUTO PAN button while pressing the
SHIFT button.
■ Patrol Learn and Play
This function gets the clear camera images on the monitor
while shooting the objects under low light conditions.
A routine of manual operations can be stored for a specific
time and later reproduced repetitively.
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. Press the AUTO PAN button two times while holding
down the SHIFT button.
"BLACK (black)" will appear on the LED display of the
controller as shown in the figure.
2. Press the AUTO PAN button three times while holding
down the SHIFT button.
"LEARN" will appear on the LED display of the controller
as shown in the figure.
RESET
CAM SETUP
SUSPEND
ALL RESET
F2
GROUP SEQ
TOUR SEQ
REW/FF
INDEX
PREV
NEXT
T&D
CAM ID
EVENT
AUX1 ON
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
DEF ON
y&
ACK
CALL
PRESET
F1
PROGRAM
PRESET
AUTO PAN
STOP
PLAY
PAUSE
MON (ESC)
OSD
SETUP
SHIFT
MON LOCK
MULTI SCREEN SEL
CAM FUNC
CAM (SET)
CLEAR
WIPER
LOG OUT
te
llig
en
3. Press the button 1 to change the image from the color
mode to the black and white mode on the active monitor.
"BL ON (BLACK ON)" appears on the LED display to
indicate the selected mode.
In
4. Press the button 2 to change the black and white image
to the color image on the active monitor.
"BL OF (BLACK OFF)" appears on the LED display to
indicate the selected mode.
RESET
SUSPEND
ALL RESET
F2
GROUP SEQ
TOUR SEQ
REW/FF
INDEX
ec
PAUSE
STOP
tS
STEP
RECORDER
ACK
CAM SETUP
ur
it
F1
Fi
re
■ Changing to Black and White Images
PREV
PAUSE
STOP
PLAY
PAUSE
EVENT
AUX1 ON
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
MON (ESC)
OSD
SETUP
CAM ID
CALL
PRESET
PROGRAM
PRESET
AUTO PAN
STEP
RECORDER
STOP
NEXT
T&D
SHIFT
MON LOCK
MULTI SCREEN SEL
CAM FUNC
DEF ON
CAM (SET)
CLEAR
WIPER
LOG OUT
3. To save the patrol sequence, follow the procedure
below.
q Press the button 2, then press the CAM (SET) button.
"LE R" appears on the LED display.
w Operate the camera manually.
e Press the button 3.
The operation data is saved and "LE S" appears on
the LED display.
5. Press the MON (ESC) button to exit from the mode.
Note: When the black and white parameter is set to
AUTO in the camera's SETUP MENU, this function
is disabled.
4. To reproduce the operation data, follow the procedure
below.
q Press the button 1.
"LE P" appears on the LED display.
w Press the button 3.
The reproduction is ended.
5. To exit from the mode, press the MON (ESC) button.
95
■ Camera Panning Function
4. To exit from the mode, press the MON (ESC) button,
then press the AUTO PAN button while holding down
the SHIFT button.
There are three panning modes available as follows: auto
pan, sort mode and sequence mode. Refer to p. 16
Camera-related Functions for details on each mode.
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
RESET
CAM SETUP
SUSPEND
ALL RESET
F2
GROUP SEQ
TOUR SEQ
REW/FF
INDEX
PREV
NEXT
T&D
CAM ID
EVENT
AUX1 ON
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
CALL
PRESET
PROGRAM
PRESET
ec
ACK
tS
F1
ur
it
y&
Fi
re
2. Press the AUTO PAN button four times while holding
down the SHIFT button.
"PAN" will appear on the LED display of the controller as
shown in the figure.
AUTO PAN
PAUSE
STOP
PLAY
PAUSE
MON (ESC)
OSD
SHIFT
MON LOCK
DEF ON
CAM (SET)
CLEAR
MULTI SCREEN SEL
WIPER
LOG OUT
In
te
SETUP
CAM FUNC
llig
STOP
en
STEP
RECORDER
3. Press the assigned numeric button shown below to activate the panning function of the selected camera.
The LED display indicates the selected mode as follows.
1: Activates AUTO PAN "PA PA".
2: Activates SORT PAN "PA SO".
3: Activates SEQUENCE PAN "PA SE".
Note: The AUTO MODE parameter previously set in the
camera's SETUP MENU will be automatically
replaced to the activated function parameter.
96
CAMERA SITE ACCESSORIES CONTROL
■ Receiver Control
● Auxiliary Control
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
The following functions are available only when the
receivers are included in the system and the specified
camera housing is installed.
2. Press the button 3 while holding down the SHIFT button
to turn on the user's auxiliary switch 1 of the receiver.
Press the button 2 while holding down the SHIFT button to turn off the user's auxiliary switch 1 of the receiver.
● Camera Housing Control
Wiper Control
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
3. Press the button 6 while holding down the SHIFT button
to turn on the user's auxiliary switch 2 of the receiver.
Press the button 5 while holding down the SHIFT button
to turn off the user's auxiliary switch 2 of the receiver.
PAUSE
PAUSE
CAM ID
EVENT
AUX1 ON
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
DEF ON
MON (ESC)
MON LOCK
CAM (SET)
MULTI SCREEN SEL
WIPER
en
tS
Defroster Control
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
llig
2. Press the button 9 while holding down the SHIFT button
to turn on the housing defroster of the camera.
te
3. To turn off the defroster, press the button 8 while holding down the SHIFT button.
TOUR SEQ
T&D
NEXT
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
PAUSE
PAUSE
EVENT
AUX1 OFF
AUX1 ON
In
STILL
CAM ID
MON (ESC)
SHIFT
97
MON LOCK
DEF ON
CAM (SET)
MULTI SCREEN SEL
WIPER
NEXT
PAUSE
ec
SHIFT
TOUR SEQ
y&
NEXT
T&D
ur
it
TOUR SEQ
Fi
re
2. Press the CAM (SET) button while holding down the
SHIFT button to turn on the housing wiper of the camera
until buttons are released.
PAUSE
T&D
CAM ID
EVENT
AUX1 ON
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
MON (ESC)
SHIFT
MON LOCK
DEF ON
CAM (SET)
MULTI SCREEN SEL
WIPER
RUNNING SEQUENCE
■ Tour Sequence
8. Press the PREV button to move the sequence one
frame to the previous step from the step that was previously paused by pressing the PAUSE button.
9. Press the STOP button to stop a tour sequence on the
active monitor and return to spot monitoring.
The following functions are available if a tour sequence has
been previously configured through SETUP MENU or WJSX150 Administrator Console. Any tour sequence can be
assigned to any monitors.
■ Group Sequence
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
The following function is available only if a group sequence
has been previously established in WJ-SX150 Administrator
Console.
As described earlier, a group sequence determines the
assignment of monitors and cameras. Therefore, monitor
selection is not required.
2. To select the desired tour sequence number, press the
numeric buttons.
Fi
re
3. When you have selected a wrong number, press the
CLEAR button to clear the numeric input.
1. Press the numeric buttons to select a desired group
sequence number.
4. Press the TOUR SEQ button to run the tour sequence in
the forward direction on the active monitor.
y&
2. When you have selected a wrong number, press the
CLEAR button to clear the numeric input.
RESET
CAM SETUP
SUSPEND
ALL RESET
F2
GROUP SEQ
TOUR SEQ
REW/FF
INDEX
PREV
NEXT
T&D
CAM ID
EVENT
STILL
AUX1 OFF
AUX1 ON
MON STATUS
ALL
tS
ACK
CALL
PRESET
PROGRAM
PRESET
en
F1
ec
ur
it
3. Press the GROUP SEQ button to run a group sequence
forward on the assigned monitors.
F1
ACK
RESET
AUTO PAN
PAUSE
STOP
PLAY
PAUSE
AUX2 OFF
ALM H
VLD H
SEQUENCE
DEF OFF
MON (ESC)
OSD
SHIFT
AUX2 ON
SYS S
MON LOCK
DEF ON
CAM (SET)
MULTI SCREEN SEL
CAM FUNC
WIPER
LOG OUT
5. Press the PAUSE button to pause a tour sequence on
the active monitor.
The "P" sign (indicating the pause status) is displayed
at the tour sequence number on the active monitor, and
a camera number currently selected appears on the
LED display.
6. Press the PAUSE button to restart a tour sequence forward from the next step that was previously paused by
pressing the PAUSE button.
7. Press the NEXT button to move the sequence one
frame to the next step from the step that was previously
paused by pressing the PAUSE button.
98
CAM SETUP
SUSPEND
ALL RESET
F2
GROUP SEQ
TOUR SEQ
REW/FF
INDEX
CLEAR
In
SETUP
EL-ZOOM
te
STOP
llig
STEP
RECORDER
PREV
NEXT
T&D
CAM ID
EVENT
AUX1 ON
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
CALL
PRESET
PROGRAM
PRESET
AUTO PAN
STEP
RECORDER
PAUSE
STOP
STOP
PLAY
PAUSE
MON (ESC)
OSD
SETUP
SHIFT
MON LOCK
MULTI SCREEN SEL
CAM FUNC
DEF ON
CAM (SET)
CLEAR
WIPER
LOG OUT
4. Press the PAUSE, NEXT or PREV button to operate the
group sequence. Refer to steps 5 to 8 of Tour
Sequence in this page for how to use these buttons.
5. To stop the sequence, select one of the monitors that
are being run on the selected group sequence, then
press the STOP button.
MONITOR DISPLAY CONTROL
■ On-screen Display (OSD) Control
■ On-screen Display (OSD) Position
Control
The procedure described below lets you determine the display parameters, such as camera title, clock and status, on
and off on the active monitor screen.
Before controlling each item, monitor selection is necessary. (Refer to p. 90 Monitor Selection.)
The procedure described below lets you determine the display positions, such as camera title, clock and status, on
the active monitor screen.
Clock
(1)
08/21/2002 12:50:28 PM
Fi
re
08/21/2002 12:50:59 PM
(4)
TOUR SEQ
REW/FF
INDEX
PREV
STEP
RECORDER
PAUSE
STOP
STOP
NEXT
PLAY
PAUSE
CAM ID
EVENT
STILL
AUX1 OFF
AUX1 ON
MON STATUS
ALL
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
MON LOCK
DEF ON
CAM (SET)
MULTI SCREEN SEL
WIPER
tS
SHIFT
M1
K1 T01
C01 camera title
en
● Displaying the Clock
ALARM10*
Camera title
EL-ZOOM
MON (ESC)
OSD
SET UP
T&D
y&
GROUP SEQ
ur
it
F2
(3)
ALARM10*
ec
(2)
M1
K1 T01
C0 1 ca mera title
F2
GROUP SEQ
TOUR SEQ
REW/FF
INDEX
PREV
NEXT
STEP
RECORDER
PAUSE
STOP
STOP
PLAY
PAUSE
SET UP
T&D
CAM ID
EVENT
AUX1 ON
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
MON (ESC)
OSD
SHIFT
llig
Toggle the button 1 while holding down the OSD button.
(1) will appear/disappear on/from the active monitor.
Event
Monitor status
MON LOCK
DEF ON
CAM (SET)
MULTI SCREEN SEL
WIPER
UP
te
● Displaying the Camera Title
L
R
In
Toggle the button 2 while holding down the OSD button.
(2) will appear/disappear on/from the active monitor.
● Displaying the Event
Toggle the button 3 while holding down the OSD button.
(3) will appear/disappear on/from the active monitor.
● Displaying the Monitor Status*
Toggle the button 4 while holding down the OSD button.
(4)* will appear/disappear on/from the active monitor.
* Monitor number, controller number and monitor mode
● Displaying All the Items
Toggle the button 5 while holding down the OSD button.
(1), (2), (3) and (4) will appear/disappear on/from the active
monitor.
99
DOWN
● Moving the Clock Display
Move the joystick while holding down the OSD, SHIFT and
1 buttons. (1) will move to the desired direction.
● Moving the Camera Title Display
Move the joystick while holding down the OSD, SHIFT and
2 buttons. (2) will move to the desired direction.
● Moving the Event Display
MODE:
Lists the display mode on the monitors.
SPOT: Spot mode
Tnn:
Tour Sequence mode (nn is the tour
sequence number.)
SET:
WJ-SX150 Setup mode
ALARM: Alarm Active mode
ACK:
Alarm ACK mode
VLD H: VLD History Table
ALM H: Alarm History Table
SYS S: System Status Table
KB:
Lists the system controller number or
PC.
OPE:
Lists the operator number
PRI:
Lists the priority number
Move the joystick while holding down the OSD, SHIFT and
3 buttons. (3) will move to the desired direction.
● Moving the Monitor Status*
Move the joystick while holding down the OSD, SHIFT and
4 buttons. (4) will move to the desired direction.
* Monitor number, controller number and monitor mode
● Moving All the Items
Move the joystick while holding down the OSD, SHIFT and
5 buttons. (1), (2), (3), and (4) will move to the desired
direction.
Fi
re
3. To exit from the mode, press the CLEAR button.
■ System Status Table
y&
The table shows the current system status.
SYSTEM STATUS
F1
ACK
MODE
T01
SPOT
ALARM
CAM
KB
K1
K2
K4
PC
OPE
1
2
4
30
PRI
30
2
1
1
en
CAM
01
02
04
16
CAM SETUP
SUSPEND
ALL RESET
te
llig
MON
1
2
3
4
tS
ec
2. Press the button 9 while holding down the OSD button.
"OSD" will appear on the LED display, and the SYSTEM
STATUS table will appear on the active monitor as
shown in the figure.
ur
it
1. Select the desired monitor. (Refer to p. 90 Monitor
Selection.)
F2
GROUP SEQ
TOUR SEQ
T&D
CAM ID
EVENT
AUX1 ON
In
RESET
REW/FF
INDEX
PREV
NEXT
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
DEF ON
CALL
PRESET
PROGRAM
PRESET
AUTO PAN
STEP
RECORDER
PAUSE
STOP
STOP
PLAY
PAUSE
MON (ESC)
OSD
SETUP
SHIFT
MON LOCK
MULTI SCREEN SEL
CAM FUNC
CAM (SET)
CLEAR
WIPER
LOG OUT
The columns in the table indicate the states as shown in the
figure.
MON:
Monitor number
CAM:
Camera number
No number indicates no camera is
selected.
100
■ Alarm History Table
■ Video Loss History Table
There are 100 alarm records stored in chronological order
in 10 pages of tables.
There are 100 video loss detection records stored in
chronological order in 10 pages of table.
1. Select the desired monitor. (Refer to p. 90 Monitor
Selection.)
1. Select the desired monitor. (Refer to p. 90 Monitor
Selection.)
2. Press the button 7 while holding down the OSD button.
"OSD" will appear on the LED display, and the ALARM
HISTORY table will appear on the active monitor as
shown in the figure.
2. Press the button 8 while holding down the OSD button.
"OSD" will appear on the LED display, and the VIDEO
LOSS HISTORY table will appear on the active monitor
as shown in the figure below.
ACK
VIDEO LOSS HISTORY
EVENT
ALARM
ACK
RESET
ALARM
ACK
RESET
ALARM
RESET
ALARM
ACK
NO
012
011
010
009
008
007
006
005
004
003
RESET
CAM SETUP
SUSPEND
ALL RESET
F2
GROUP SEQ
TOUR SEQ
REW/FF
INDEX
ALARM
03
03
03
07
07
07
09
09
06
06
PREV
NEXT
F1
T&D
CAM ID
EVENT
AUX1 ON
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
DEF ON
CALL
PRESET
PROGRAM
PRESET
STOP
PLAY
PAUSE
OSD
SHIFT
MON (ESC)
CAM (SET)
CLEAR
MON LOCK
WIPER
LOG OUT
MULTI SCREEN SEL
llig
SETUP
CAM FUNC
en
PAUSE
STOP
tS
AUTO PAN
STEP
RECORDER
YYYY/MM/DD
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
ur
it
F1
HH:MM:SS
18:59:08
18:58:08
18:57:08
18:55:08
18:54:08
18:53:08
18:53:00
18:52:08
18:51:08
18:50:08
HH:MM:SS
18:59:08
18:58:08
18:57:08
18:55:08
18:54:08
18:53:08
18:53:00
18:52:08
18:51:08
18:50:08
CH
03
14
09
07
08
16
09
14
06
01
1 of 2
EVENT
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
RECOVER
RECOVER
LOSS
LOSS
LOSS
LOSS
LOSS
LOSS
LOSS
RECOVER
y&
YYYY/MM/DD
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
2001/08/21
ec
NO
016
015
014
013
012
011
010
009
008
007
1 of 2
Fi
re
ALARM HISTORY
ACK
RESET
CAM SETUP
SUSPEND
ALL RESET
F2
GROUP SEQ
TOUR SEQ
REW/FF
INDEX
PREV
NEXT
T&D
CAM ID
EVENT
AUX1 ON
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
DEF ON
CALL
PRESET
PROGRAM
PRESET
AUTO PAN
STEP
RECORDER
PAUSE
STOP
STOP
PLAY
PAUSE
MON (ESC)
OSD
SETUP
SHIFT
MON LOCK
MULTI SCREEN SEL
CAM FUNC
CAM (SET)
CLEAR
WIPER
LOG OUT
The columns in the table indicate the states as follows:
DATE:
te
The columns in the table indicate the states as follows:
In
Lists the date and time when the alarm state
changes.
ALARM: Lists the alarm number (01 - 16).
EVENT: Lists the event when the alarm state changes.
3. Press the NEXT button to select the next page of the
history, and press the PREV button to back up to the
previous page.
4. To exit from the mode, press the CLEAR button.
101
DATE:
Lists the date and time when the video loss
state changes.
CH:
Lists logical camera number that is connected
to the system.
EVENT: Lists the event when the video loss state
changes.
ALARM CONTROL
■ Alarm Mode
■ Operating during an Alarm Mode
When alarm (sensor) is accepted, the matrix switcher's
operation mode changes to the alarm mode. Then, the system operates as follows:
• The camera image (alarm image) appears on the monitor.
In the factory default setting, the alarm inputs 1 to 16
are associated with the same-numbered camera input
connectors. All the video output signals are sent to
Monitor 1. For example, when the alarm (sensor) connected to the alarm input 1 becomes active, the camera
input connector 1’s image appears on Monitor 1.
• "ALARMnn" appears on the monitor.
The display indicates the image is input through the
alarm nn (nn is the alarm number).
When more than one alarm signal input has been
accepted, "ALARMnn*" appears on the monitor.
While an alarm mode is active, the following are available
from the system controller:
• Operating the camera with the alarm input (ACK)
• Resetting the alarm (RESET/ALL RESET)
• Suspending the alarm (ALM SUSPENDED)
■ Operation of an Alarm-related
Camera (ACK)
ACK
Fi
re
You can operate the camera with the alarm input as follows:
RESET
SUSPEND
ALL RESET
TOUR SEQ
y&
GROUP SEQ
REW/FF
ALARM01
PREV
NEXT
PLAY
tS
en
llig
te
In
There are two operation mode when more than one
alarm signal has been accepted by the unit that is
assigned to the same monitor.
• Sequence mode: An alarm operation is replaced by
another one after the dwell time ends.
• Hold mode: An initial alarm operation is continued
even after another alarm input is accepted.
Notes:
• The association of the alarm inputs with cameras and
monitors are changeable in SETUP MENU or WJ-SX150
Administrator Console. (Refer to p. 56 or p. 74.)
• Alarm input will be automatically reset in 30 seconds.
The auto-recovery time is configurable through SETUP
MENU or WJ-SX150 Administrator Console.
102
PAUSE
PAUSE
CAM ID
EVENT
AUX1 ON
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
MON (ESC)
OSD
ec
• Alarm output signals are supplied from Alarm Output 1
to 4 (#10, 11, 23 and 24) of the ALARM port (25-pin Dsub connector) at the rear panel. Alarm Output 1 to 4 is
associated with MONITOR OUT 1 to 4. For example,
when an alarm input signal is activated on MONITOR
OUT 1, the unit supplies Alarm Output 1 to Monitor 1.
• The monitor and alarm number will appear on the LED
display. At the same time, the alarm indicator will blink,
the monitor indicator will light up, and the camera indicator will go out.
ur
it
STEP
T&D
SHIFT
MON LOCK
ACK
DEF ON
CAM (SET)
MULTI SCREEN SEL
WIPER
1. Select a monitor which displays "ALARM".
2. Press the ACK button.
"ACK" will appear on the monitor with an alarm input.
The camera with an alarm input will become operable.
3. Operate camera with the system controller.
Pan/Tilt, zoom, focus, and iris are available.
When selecting another monitor, "ACK" will disappear
from the display. The matrix switcher system will return
to the alarm mode.
■ Resetting the Alarm Inputs
● Alarm All Reset
RESET
There are two alarm reset functions:
• Alarm reset (resetting the alarm inputs according to the
input order)
• Alarm all reset (resetting all the alarm inputs)
ALL RESET
TOUR SEQ
T&D
CAM ID
EVENT
STILL
AUX1 OFF
AUX1 ON
NEXT
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
RESET
PAUSE
ALL RESET
TOUR SEQ
T&D
CAM ID
EVENT
STILL
AUX1 OFF
AUX1 ON
PAUSE
MON (ESC)
MON LOCK
SHIFT
DEF ON
CAM (SET)
MULTI SCREEN SEL
WIPER
● Alarm Reset
Fi
re
ec
Use this function when you do not want to be disturbed by
an alarm input, for example, during the setup procedures.
Time
ACK
RESET
SUSPEND
ALL RESET
GROUP SEQ
TOUR SEQ
REW/FF
PREV
In
te
Matrix switcher
en
tS
Alarm
input 2
llig
Alarm
input 1
y&
■ Suspending the Alarm Inputs
• Description about alarm reset
Alarm
input 5
1. Press the RESET button while holding down the SHIFT
button.
2. The monitor, the LED display and the indicator will
change as follows:
"ALARMnn" will disappear from the monitor.
The LED display will return to the state before the
alarm input.
The alarm indicator will go out.
The CAM indicator will return to the state before the
alarm input.
ur
it
1. Select a monitor which displays "ALARM".
2. When more than one alarm signal has been input, the
second earliest alarm image appears on the monitor,
after the current alarm image is reset.
3. To reset all the alarms, repeat steps 1 and 2. The monitor, the LED display and the indicator will change as follows:
"ALARMnn" will disappear from the monitor.
The LED display will return to the state before the
alarm input.
The alarm indicator will go out.
The CAM indicator will return to the state before the
alarm input.
ALARM01*
Monitor 1
RESET
NEXT
STEP
PAUSE
PLAY
PAUSE
T&D
CAM
STILL
AUX1 O
MON STATUS
ALM SUSPENDED
ALL
EL-ZOOM
AUX2 O
ALM H
VLD
SEQUENCE
DEF O
MON (ESC)
OSD
SHIFT
MON LOCK
MULTI SCRE
ALL RESET
ALARM05*
RESET
ALL RESET
ALARM02
Monitor 1
Note: When more than one alarm is input and they are
associated with the same monitor, they will be reset one
by one.
103
1. Press the ACK/SUSPEND button while holding down
the SHIFT button.
"ALM SUSPENDED" will appear on the monitor.
2. To cancel alarm suspension, press the ACK/SUSPEND
button while holding down the SHIFT button again.
"ALM SUSPENDED" will disappear from the monitor.
Notes:
• An alarm continues to operate even after it is suspended.
• If you suspend an alarm while an alarm image is displayed, "ALM SUSPENDED" will not appear on the monitor. Reset the alarm, and then suspend it again.
MULTIPLEXER OPERATIONS
● Still Playback Spot Picture
Multiplexer board WJ-SXB151 is an optional board.
It enables multiscreen display, electronic zooming, still picture and multiscreen sequence.
It also enables the operation of Digital Disk Recorder WJHD100 Series or time-lapse VCR, when connected to them.
Note: Before the use, it is necessary to install the
Multiplexer board in the matrix switcher and configure the system through SETUP MENU and WJSX150 Administrator Console. [Refer to p. 34
Installing the Multiplexer Board, p.52 WJ-SX150
SETUP MENU (OSD), and p. 64 WJ-SX150 ADMINISTRATOR CONSOLE.]
The spot picture is changed into the still picture.
1. Select the desired monitor and camera number. (Refer
to p. 90 Monitor Selection and Camera Selection.)
The monitor number and camera number will appear on
the LED display.
2. Press the RECORDER button. (Refer to p. 116 Recorder
Mode.) The system will enter the recording mode.
3. Press the PLAY button. (Refer to p. 117 Normal
Playback.) The system will enter the playback mode.
Fi
re
4. Select a camera channel by pressing a numeric button
and then pressing the CAM (SET) button. The selected
camera image will be displayed in a spot picture.
■ Monitoring the Camera Picture
y&
5. Press the button 1 while holding the SHIFT button. The
selected camera image will change into the still picture.
● Multiscreen Segment Switching
● Multiscreen Sequence
llig
en
tS
ec
Camera images are switched automatically in a sequence
mode.
The sequence mode (QUAD, 3+1, 8+1) is configurable
through WJ-SX150 Administrator Console.
(Refer to p. 82 Sequence Mode of Multiplexer Mode for
details.)
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
The monitor number and camera number will appear on
the LED display.
6. To cancel the still picture, press the button 1 while holding down the SHIFT button again.
Note: Still picture is not available while zooming is activated.
ur
it
Refer to p. 117 Multiscreen Segment Switching for details.
In
te
2. Press the RECORDER button. (Refer to p. 116 Recorder
Mode.) The system will enter the recorder mode.
3. Press the button 7 while holding down the SHIFT button.
A sequence of multiscreen pictures is displayed
according to the WJ-SX150 Administrator Console's
configuration.
4. To cancel the sequence, press the button 0 while holding down the SHIFT button.
Note: The sequence mode can also be cancelled by pressing a numeric button (corresponding one to the monitor
number), then the CAM (SET) button.
104
● Still Multiscreen Picture
Still pictures can also be displayed in a multiscreen.
1. Select the desired monitor and camera number. (Refer
to p. 90 Monitor Selection and Camera Selection.)
The monitor number and camera number will appear on
the LED display.
2. Press the RECORDER button. (Refer to p. 116 Recorder
Mode.) The system will enter the recorder mode.
3. Press the numeric button corresponding to the camera
number.
4. Press the button 1 while holding down the SHIFT button.
The selected camera image will change into the still
picture.
"STILL" and the camera title alternately blinks on the
monitor.
5. To cancel the still picture, press the button 1 while holding down the SHIFT button again.
Notes:
• “STILL” does not appear when the still display is set to
OFF.
• When you skip Step 3 and do Step 4, all the channels
displayed in the multiscreen segments will be changed
into the still pictures.
● Electronic Zooming (EL-ZOOM)
Playback spot pictures can be electrically zoomed.
1. Select the desired monitor. (Refer to p. 90 Monitor
Selection and p. 91 Camera Selection.)
2. Press the RECORDER button. (Refer to p. 116 Recorder
Mode.) The system will enter the recorder mode.
3. Press the PLAY button. (Refer to p. 117 Normal
Playback.) The system will enter the playback mode.
4. Select a camera channel by pressing a numeric button
and then pressing the CAM (SET) button. The selected
camera image will be displayed in a playback spot picture.
Fi
re
5. Press the button 4 while holding down the SHIFT button.
“+” sings will appear on the image.
ec
8. To move the zoom area, move the joystick.
ur
it
7. Press the button 4 while holding down the SHIFT button. The area surrounded by the “+” signs will be
zoomed up.
y&
6. To move the “+” signs within the picture, move the joystick.
In
te
llig
en
tS
9. To cancel the zooming, press the button 4 while holding
down the SHIFT button again.
Note: Still picture is not available while zooming is activated.
105
Fi
re
In
te
llig
en
tS
ec
ur
it
y&
OPERATING PROCEDURES
(PS·DATA)
107
WHEN USING A PS·DATA SYSTEM CONTROLLER
This manual describes the operating procedures which are specifically related to WJ-SX150.
For the basic operating procedures such as log-in/log-out, camera selection, and camera control, etc., refer to the system controller's operating instructions.
The following are different from the terminal mode when you use the system controller via the PS·Data protocol.
Fi
re
• Camera selection, camera control, camera site accessories control are in accordance with the PS·Data System operating
procedures. Refer to the system controller's operating instructions.
• You cannot reset an alarm one by one per monitor. However, you can reset all the alarms at a time (ALL RESET).
• You cannot acknowledge an alarm.
• You cannot use the auto log-in function of the unit. To use this function, use a terminal-mode system controller.
• You cannot use the auto log-out function of the unit.
• You cannot move the clock, camera title, event, and/or monitor status display with a PS·Data controller. Use a terminalmode system controller.
• Operators using the PS·Data system controller have the highest priority to all those using the terminal-mode system controllers.
• PS·Data doesn’t support user-management, and you cannot configure the PS·Data operator registration neither through
SETUP MENU nor WJ-SX150 Administrator Console.
In
te
llig
en
tS
ec
ur
it
y&
Notes:
• When you select a monitor with a PS·Data system controller, you might enter its number as you do in the terminal mode.
However, the matrix switcher regards a monitor as a unit, you need to select it by the unit number. (Refer to p. 109.)
• This unit is counted as 4 PS·Data units. Confirm the total number of the PS·Data units in your system.
(Up to 16 PS·Data units are available.)
108
MONITOR CONTROL
■ Priority Lock
Refer to the system controller’s operating instructions
before you login the system. After the log-in procedure, the
following operations are available to control the system.
The operation begins with selecting a monitor, then the
selected camera appears the active monitor.
You can apply or release priority lock by entering the function code. Monitor display is the same as those of terminal
mode. (Refer to p. xx for the illustrations.)
1. Select the desired monitor. (Refer to Monitor Selection).
2. Press the SHIFT button, and enter 101 by pressing the
numeric buttons.
■ Monitor Selection
Unit addresses are given to each monitor.
Mon 1
1
Mon 2
2
Mon 3
3
3. Press the FUNCTION button. The function will be executed.
If the priority lock mode is selected, the monitor number
will inversely appear on the active monitor.
Mon 4
4
Fi
re
Rotary SW
1
The following is how to select a monitor.
1. Press the numeric button(s) to select the desired monitor's unit address.
2. Press the UNIT button.
The selected monitor will be activated.
4. To release the priority lock, do steps 2 and 3 again.
In
te
llig
en
tS
ec
ur
it
y&
Note: This function will prevent operators in the terminal
mode from gaining control of a monitor. However, operators via the PS·Data protocol can still gain control.
109
RUNNING SEQUENCE
■ Group Sequence
The following functions are available if a tour sequence has
been previously configured through SETUP MENU or WJSX150 Administrator Console. Any tour sequence can be
assigned to any monitors.
1. Select the desired monitor. (Refer to p. 109 Monitor
Selection.)
The following function is available only if a group sequence
has been previously established in WJ-SX150 Administrator
Console. The group sequence has ID numbers. Group 1 is
17, Group 2 is 18, Group 3 is 19, and Group 4 is 20.
As described earlier, a group sequence determines the
assignment of monitors and cameras. Therefore, monitor
selection is not required.
2. To select the desired tour sequence number, press the
numeric buttons.
1. Press the numeric buttons to select a desired group
sequence ID number, then press the SEQ button.
3. Press the SEQ button to run the tour sequence in the
forward direction on the active monitor.
2. Press the SEQ button to run a group sequence forward
on the assigned monitors.
4. Press the SEQ PAUSE button to pause a tour sequence
on the active monitor.
A series of camera picture appear in pause on the monitor screen for the specified dwell time.
5. Press the SEQ PAUSE button again to restart a tour
sequence forward from the next step that was previously paused by pressing the SEQ PAUSE button.
In
te
llig
en
y&
tS
ec
6. Press the SHIFT button, and then press the + button to
move the sequence one frame to the next step from the
step that was previously paused by pressing the
PAUSE button.
Press the SHIFT button, and then press the - button to
move the sequence one frame to the previous step from
the step that was previously paused by pressing the
PAUSE button.
7. Select a camera (refer to the system controller's operating instructions) to stop the sequence. The monitor will
return to the spot mode.
6. Press the SHIFT button, and then press the + button to
move the sequence one frame to the next step from the
step that was previously paused by pressing the
PAUSE button.
Press the SHIFT button, and then press the - button to
move the sequence one frame to the previous step from
the step that was previously paused by pressing the
PAUSE button.
ur
it
5. Press the SEQ PAUSE button again to restart a tour
sequence forward from the next step that was previously paused by pressing the SEQ PAUSE button.
Fi
re
■ Tour Sequence
110
7. Select a camera (refer to the system controller's operating instructions) to stop the sequence. The monitor will
return to the spot mode.
MONITOR DISPLAY CONTROL
The procedure described below lets you determine on-screen display (OSD) items, such as camera title, clock and status, on
and off on the active monitor screen.
Before controlling each item, monitor selection is necessary. (Refer to p. 109 Monitor Selection.)
1. Press the SHIFT button, and then press the numeric buttons corresponding to the function code.
(Refer to the table.)
2. Press the FUNCTION button. The function will be executed.
Controller Status
Note
Code
Displaying the clock
104
Pressing again will hide the display.
Displaying the camera title
105
Pressing again will hide the display.
Displaying the event
106
Pressing again will hide the display.
Displaying the monitor status
107
Pressing again will hide the display.
Displaying all the items
19
Pressing again will hide the display.
Displaying System Status
102
"OSD" appears on the LED.
Pressing again will return to the normal display.
Displaying Video Loss History
103
"OSD" appears on the LED.
Pressing again will return to the normal display.
ur
it
y&
Fi
re
Function
In
te
llig
en
tS
ec
Notes:
• Alarm History Table doesn't have a function code. When displaying the table, press the ALM RECALL button instead of
the steps 1 and 2 above. "OSD" will appear on the LED display, and the ALARM HISTORY table will appear on the
active monitor.
• You cannot control OSD display position.
111
ALARM CONTROL
■ Alarm Mode
■ Resetting All the Alarm Inputs
When alarm (sensor) is accepted, the matrix switcher's
operation mode changes into the alarm mode. Then, the
system operates as follows:
• The camera image (alarm image) appears on the monitor.
In the factory default setting, the alarm inputs 1 to 16
are associated with the same-numbered camera input
connectors. All the video output signals are sent to
Monitor 1. For example, when the alarm (sensor) connected to the alarm input 1 becomes active, the camera
input connector 1’s image appears on Monitor 1.
• "ALARMnn" appears on the monitor.
The display indicates the image is input through the
alarm nn (nn is the alarm number).
When more than one alarm signal input has been
accepted, "ALARMnn*" appears on the monitor.
You can reset all the alarm input signals at a time.
2. Press the SHIFT button, and then press the ALL RESET
button.
All the alarms will be reset.
Then, the LED display and indicators will return to the
state before the alarm input.
Fi
re
Note: You cannot reset the alarm input signals one by one.
y&
■ Suspending All the Alarm Inputs
Use this function when you do not want to be disturbed by
an alarm input, for example, during the setup procedures.
ur
it
1. To suspend all the alarm input signals, press the SHIFT
button., and then press the SUSPEND button.
The indicator beside the button will light up and "ALM
SUSPENDED" will appear on the monitor.
(Refer to the figure on p. 103.)
en
tS
ec
• The alarm indicator will blink.
• Alarm output signals are supplied from Alarm Output 1
to 4 (#10, 11, 23 and 24) of the ALARM port (25-pin Dsub connector) at the rear panel. Alarm Output 1 to 4 is
associated with MONITOR OUT 1 to 4. For example,
when an alarm input signal is activated on MONITOR
OUT 1, the unit supplies Alarm Output 1 to Monitor 1.
• The monitor and alarm number will appear on the LED
display. At the same time, the alarm indicator will blink,
the monitor indicator will light up, and the camera indicator will go out.
1. Select a monitor which displays "ALARM".
(Refer to the figure on p. 102.)
In
te
llig
Notes:
• The association of the alarm inputs with cameras and
monitors are changeable in SETUP MENU or WJ-SX150
Administrator Console. (Refer to p. 56 or p. 74.)
• Alarm input will be automatically reset in 30 seconds.
The auto-recovery time is configurable through SETUP
MENU or WJ-SX150 Administrator Console.
■ Operation during an Alarm Mode
While an alarm mode is active, you can do the following:
• Resetting all the alarm inputs (ALL RESET)
• Suspending all the alarm inputs (ALM SUSPENDED)
112
2. To cancel alarm suspension, do Step 1 again.
Notes:
• The alarm suspension is applied to all system units,
not to a selected one.
• An alarm which was input before the suspension
will continue to operate.
MULTIPLEXER OPERATIONS (PS · Data)
This section will describe what you should take notice when
using a PS·Data system controller. The same descriptions
as the system controller’s operating instructions are not
mentioned here. Refer to them.
■ Controlling the Unit with a PS·Data
System Controller
In
te
llig
en
tS
ec
ur
it
y&
Fi
re
1. Before operating the recorder, it is necessary to enter
the recorder mode. (Refer to p. 124 or p. 125.)
2. Enter the desired function code (refer to the diagram)
and press the FUNCTION button.
113
tS
en
llig
te
In
ec
y&
ur
it
EXPANDED FUNCTION
115
Fi
re
WJ-HD500 SERIES CONTROL (TERMINAL MODE)
Matrix switcher can control Digital Disk Recorder WJHD500 Series. The following is the procedure of WJ-HD500
Series SETUP MENU.
NEXT button: Increments a parameter.
PREV button: Decrements a parameter.
MON (ESC) button: Returns to SETUP MENU or the
previous menu.
Notes:
• The following operating procedures are for the terminal
mode. If you are using a PS·Data system controller,
refer to p. 124.
• When a Multiplexer board is installed in the unit, you
can neither connect nor control a WJ-HD500 Series
recorder. You need to remove the board from the unit.
UP
L
R
DOWN
CAM SETUP
F2
To display WJ-HD500 Series SETUP MENU, follow the procedure below.
INDEX
RESET
SUSPEND
ALL RESET
GROUP SEQ
TOUR SEQ
REW/FF
y&
PREV
RECORDER
1. Confirm that WJ-HD500 Series is correctly and securely
connected.
ur
it
STOP
STOP
SETUP
PLAY
NEXT
T&D
CAM ID
EVENT
AUX1 ON
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
DEF ON
CALL
PRESET
PROGRAM
PRESET
AUTO PAN
STEP
PAUSE
PAUSE
MON (ESC)
OSD
SHIFT
MON LOCK
MULTI SCREEN SEL
CAM FUNC
CAM (SET)
CLEAR
WIPER
LOG OUT
tS
ec
2. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
The monitor number and camera number will appear on
the LED display.
ACK
Fi
re
F1
■ Displaying WJ-HD500 Series SETUP
MENU
te
llig
en
3. Press the RECORDER button.
The system will enter the recorder mode and the selected monitor will change into multiscreen display. Then,
the selected monitor number and "-H00" will appear on
the LED display
In
4. Press the SETUP button while holding down the SHIFT
button on the system controller.
WJ-HD500 Series SETUP MENU will appear on the
active monitor and the system controller's SETUP indicator will light up.
The following functions and buttons are valid in SETUP
MENU.
Joystick to UP (▲): Moves the cursor up.
Joystick to DOWN (▼): Moves the cursor down.
Joystick to L (t): Moves the cursor to the left.
Joystick to R (s): Moves the cursor to the right.
CAM (SET) button: Executes the selections and displays a submenu.
116
5. To end the setting and return to the normal view, press
the SETUP button while holding down the SHIFT button
when SETUP MENU is displayed. The system controller's SETUP indicator will go out.
■ Controlling Digital Disk Recorder WJHD500 Series
The following are the operating procedures of WJ-HD500
Series via system controller.
Note: Refer to the operating instructions of Digital Disk
Recorder WJ-HD500 Series for details.
● Recorder Mode
Before operating the recorder, it is necessary to enter the
recorder mode.
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
The monitor number and camera number will appear on
the LED display.
2. Press the RECORDER button to enter the recorder
mode.
● Normal Playback
• The indicator beside the RECORDER button will
light up, and the images from the recorder are displayed on the active monitor in multiscreen segments.
• The CAMERA indicator will go out and the monitor
number with "-H00" will appear on the LED display.
1. Enter the recorder mode (Refer to p. 116 Recorder
Mode.)
2. To start the playback, press the PLAY button. The system will enter the playback mode. Then, the most
recent recorded image will be played back.
UP
RECORDER
L
R
00: Multiscreen display
01 to 16: Spot display (camera number)
DOWN
TOUR SEQ
REW/FF
INDEX
PREV
PAUSE
y&
STOP
STOP
PLAY
PAUSE
T&D
CAM ID
EVENT
AUX1 ON
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
MON (ESC)
OSD
SHIFT
MON LOCK
DEF ON
CAM (SET)
MULTI SCREEN SEL
WIPER
ur
it
SETUP
NEXT
STEP
RECORDER
You can also exit from the recorder mode by pressing
the RECORDER button during the recorder mode.
Note: Only one operator can enter the recorder mode.
ec
● Multiscreen Segment Switching
GROUP SEQ
Fi
re
F2
3. To exit from the recorder mode, select the camera.
(Refer to p. 91 Camera Selection.) The indicator beside
the button will go out. The monitor number and camera
number will appear on the LED display again.
tS
Multiscreen segment patterns are configurable through WJHD500 SETUP.
(Refer to the recorder’s operating instructions.)
In
te
llig
en
1. Enter the recorder mode (Refer to p. 116 Recorder.)
2. Press the RECORDER button again. Every time you
press the button, the multiscreen segment patterns are
switched. (The following is the factory default setting.)
4A (Page 1 of the quad → Camera 1, 2, 3, and 4) → 4B
(Page 2 - Camera 5, 6, 7 and 8) → 4C (Page 3 Camera 9, 10, 11 and 12) → 4D (Page 4 – Camera 13,
14, 15 and 16) → 7 (segments) → 9 →10 → 13 → 16 →
4A
3. To return to the spot display, exit from the recorder
mode.
Note: Multiscreen segment patterns are not configurable
through WJ-SX150 Administrator Console.
•
•
•
•
To pause the playback, press the PAUSE button.
To stop the playback, press the STOP button.
To resume the playback, press the PLAY button.
To move forward/backward search during the playback, move the joystick rightward/leftward, or press
REW/FF button.
Joystick to R (B)/FF ( ): Search forward
Joystick to L (A)/REW ( ): Search backward
• To move forward/backward field advance during
the pause, move the joystick rightward/leftward, or
press REW/FF button.
Joystick to R (B)/STEP ( ): Forward field
advance
Joystick to L (A)/STEP ( ): Backward field
advance
• To display the spot picture, press the numeric button corresponding to the desired camera number,
then press the CAM (SET) button. Then, the active
monitor number with "-H** (** is the camera number)" will appear on the LED display.
• To resume the multiscreen display, press the button
0 while holding down the SHIFT button.
• To change the number of multiscreen segments,
press the button 0 while holding down the SHIFT
button again during the multiscreen display.
117
3. To stop the playback, press the STOP button. The monitor display will return to the multiscreen display.
● Manual Recording
● Electronic Zooming (EL-ZOOM)
1. Enter the recorder mode (Refer to p. 116 Recorder
Mode.)
Playback images can be electrically zoomed besides a
camera's optical zooming.
2. To start recording, press the WIDE and TELE buttons
simultaneously.
The digital disk recorder will start recording.
1. Enter the recorder mode (Refer to p. 116 Recorder
Mode.)
2. Press the PLAY button.
3. To stop the recording, press the STOP button while
holding down the SHIFT button.
3. Press the numeric button corresponding on the desired
camera number to display the spot picture.
ZOOM
WIDE
4. Press the CAM (SET) button.
The selected camera’s picture is displayed in the spot
mode.
TELE
REC
Fi
re
Note: Refer to WJ-HD500 Series Operating Instructions
for details and other recording modes.
● Search Playback
y&
ur
it
UP
L
R
ec
You can search playback images using the Record List or
Thumbnail Display. Every time you press the INDEX button,
the display will change as follows.
Live image → Record List → Thumbnail Display -→ Live
image
You can operate the Record List or Thumbnail Display by
referring to the recorder’s operating instructions. In addition, the following operations from the system controllers
are also available.
5. Each time the button 4 and the SHIFT button are
pressed, the zooming range are changeable as follows:
2x → 4x → 8x → 1x → 2x
DOWN
F2
GROUP SEQ
REW/FF
INDEX
PREV
NEXT
STEP
RECORDER
PAUSE
STOP
STOP
TOUR SEQ
PLAY
PAUSE
CAM ID
EVENT
AUX1 ON
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
MON (ESC)
OSD
SETUP
T&D
SHIFT
MON LOCK
DEF ON
CAM (SET)
MULTI SCREEN SEL
WIPER
In
te
llig
en
tS
Joystick to UP (D): Moves the cursor up.
Joystick to DOWN (C): Moves the cursor down.
Joystick to L (A): Moves the cursor to the left.
Joystick to R (B): Moves the cursor to the right.
CAM(SET) button: Displays the search editing area./Starts
the search after you enter the search condition.
MON(ESC)button: Cancels the search editing area and
returns to the Record List or Thumbnail Display.
NEXT button: Increments a parameter.
PREV button: Decrements a parameter.
PLAY button: Starts the playback of a record pointed by
the cursor.
Note: The PLAY button is deactivated in the search editing
area.
6. To return the zooming range to x 1, press the button 4
while holding down the SHIFT button again.
7. To return to the multiscreen display, press the button 0
while holding down the SHIFT button.
Notes:
• You can move the zoomed area on the monitor with
the joystick after Step 4.
• You can also display the still picture after step 4.
118
● Multiscreen Sequence
Digital disk recorder starts a sequence according to the
setting of WJ-HD500 Series.
1. Enter the recorder mode (Refer to p. 116 Recorder
Mode.)
2. Press the button 7 while holding down the SHIFT button.
TOUR SEQ
REW/FF
PREV
NEXT
STEP
PAUSE
PLAY
PAUSE
T&D
CAM ID
EVENT
AUX1 ON
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
MON (ESC)
OSD
SHIFT
MON LOCK
DEF ON
CAM (SET)
MULTI SCREEN SEL
Fi
re
GROUP SEQ
WIPER
In
te
llig
en
tS
ec
SHIFT + ZOOM WIDE buttons: Selects a group to be
SHIFT + ZOOM TELE buttons: Changes the display mode
of the Record List between the alarm search ON and
OFF.
ON: Displays only the Alarm and Emergency Record
List of the selected group.
OFF: Displays all the record lists for the selected
group.
ur
it
● Other Operations
y&
3. To cancel the sequence, press the button 0 while holding down the SHIFT button.
The display will change into the multiscreen display.
119
WJ-HD100 SERIES CONTROL (TERMINAL MODE)
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
The monitor number and camera number will appear on
the LED display.
Digital Disk Recorder WJ-HD100 Series are operable with
the system controller, while connecting to the matrix switcher.
Note: Before the use, it is necessary to install the multiplexer board in the matrix switcher, connect the
matrix switcher to the digital disk recorder, and configure the system through WJ-SX150 Administrator
Console, OSD SETUP MENU, and WJ-HD100 Series
SETUP MENU. [Refer to p. 34 Installing the
Multiplexer Board, p.44 Connection with Digital Disk
Recorder WJ-HD100 Series, p. 52 WJ-SX150
SETUP MENU (OSD), p. 64 WJ-SX150 ADMINISTRATOR CONSOLE, and Displaying WJ-HD100
Series SETUP MENU in this page.]
2. Press the RECORDER button on the system controller.
The system will enter the recorder mode and the
RECORDER indicator beside the button will light up.
2. To start the playback, press the PLAY button.
3. To pause the playback, press the PAUSE button.
Fi
re
4. To resume the playback, press the PLAY button.
5. To stop the playback, press the STOP button.
The following is the procedure of WJ-HD100 Series SETUP
MENU.
The following functions and buttons are valid in SETUP
MENU.
Joystick to R (B): Decrements a parameter
Joystick to L (A): Increments a parameter
y&
ur
it
● Forward or Backward Search
The recorded images can be searched at variable speeds.
This function is available during the playback or playback
pause. (Refer to Normal Playback in the previous page.)
Move the joystick rightward or leftward to search images.
ec
■ Displaying WJ-HD100 Series SETUP
MENU
Note: Refer to WJ-HD100 Series Operating Instructions
for details and other playback modes.
en
tS
The operations are the same as WJ-HD500 Series.
Refer to p.116 Displaying WJ-HD500 Series SETUP MENU.
llig
■ Controlling Digital Disk Recorder WJHD100 Series
te
The following are the operating procedures of WJ-HD100
Series via the system controller.
In
● Multiscreen Segment Switching
The operating procedure is the same as WJ-HD500 Series.
(Refer to p118)
Note: 7-, 10-, or 13-segment multiscreen display is
unavailable.
● Manual Recording
The operations are the same as WJ-HD500 Series.
Refer to p. xx.
Joystick to R(B): Search forward
Joystick to L(A): Search backward
The joystick inclination can control the forward/backward
search speed.
● Forward or Backward Field Advance
The recorded images can be searched field by field.
During the pause, move the joystick rightward or leftward to
advance an image field by field.
Joystick to R(B): Forward field advance
Joystick to L(A): Backward field advance
● Search Playback
You can search playback images using the ALARM
RECALL table or the SEARCH table.
Every time you press the INDEX button, the display will
change as follows.
Live image → ALARM RECALL table → Date-and-time
entry form → Live image
● Normal Playback
Monitor display can be divided into 4, 9, or 16 multiscreen
segments to display camera images.
120
The operations are the same as WJ-HD500 Series.
Refer to p. 118 Search Playback.
• ALARM RECALL table
The recorder’s alarm history will be displayed on the
ALARM RECALL table.
Move the cursor with the joystick to the desired alarm
number, and then press the PLAY button. The associated image will be played back.
ALARM RECALL 1 OF
DATE
TIME
JUN 9.00 00:00:00
JUN 1.00 02:34:56
JUN 1.00 01:10:01
MAY31.00 23:34:45
MAY30.00 02:00:20
MAY14.00 05:30:31
MAY 7.00 23:00:59
MAY 6.00 22:05:50
APR14.00 23:00:59
APR14.00 16:06:34
10
ALM
* T
T
* V
V
* T
* T
T
V
* T
* V
Fi
re
NO
99
98
97
96
95
94
93
92
91
90
• Date-and-time entry form
y&
F2
ur
it
INDEX
en
tS
ec
SEARCH
YYYY/MM/DD HH:MM
2002/05/07 19:32
llig
Note: To cancel the entry form, press the CLEAR button.
In
te
1. Press the numeric buttons to enter the date and time
written down in step 2. The cursor can be adjusted by
moving the joystick rightward or leftward.
UP
L
R
DOWN
2. Press the PLAY button. After the search through the
date and time, the recorded image will be played.
3. To return to the multiscreen display, press the STOP
button.
121
TIME-LAPSE VCR CONTROL [PANASONIC MODELS] (TERMINAL MODE)
● Rewind
A time-lapse VCR (Panasonic Models) is operable with the
system controller, while connecting to the matrix switcher.
1. During the stop, press the REW button to rewind the
tape.
2. Press the STOP button to stop rewinding.
Note: Pressing the PLAY button during rewind will start
playback.
Note: Before the use, it is necessary to install the
Multiplexer board in the matrix switcher, connect
the matrix switcher to the time-lapse VCR, and configure the system through WJ-SX150 Administrator
Console, OSD SETUP MENU, and time-lapse VCR's
SETUP MENU. [Refer to p. 34 Installing the
Multiplexer Board, p. 45 Connection with the Timelapse VCR (Panasonic Models), p. 52 WJ-SX150
SETUP MENU (OSD), and p. 64 WJ-SX150 ADMINISTRATOR CONSOLE.]
● Forward or Backward Search
Fi
re
The recorded images can be searched at variable speeds.
This function is available during the playback or playback
pause. (Refer to p. 117 Normal Playback.)
Move the joystick rightward or leftward to search images.
Joystick to R (B)/FF ( ): Search forward
Joystick to L (A)/REW ( ): Search backward
The following is the procedure of a Panasonic model timelapse VCR.
y&
The joystick inclination can control the forward/backward
search speed.
During the search noise may appear on the image.
■ Controlling the Time-lapse VCR
tS
The operations are the same as WJ-HD500 Series.
Refer to p.xx Multiscreen Display.
en
● Manual Recording
te
llig
The operations are the same as WJ-HD500 Series.
Refer to p.xx Manual Recording.
● Normal Playback
In
The operations are the same as WJ-HD500 Series.
Refer to p.xx Normal Playback.
● Fast-forward
1. Press the FF button to fast-forward the tape during the
stop.
2. To stop fast-forwarding, press the STOP button.
Note: Pressing the FF button during fast-forward will
start playback.
122
ur
it
● To Operate Multiscreen Display
● Forward or Backward Field Advance
The recorded images can be searched field by field.
During the pause, move the joystick rightward or leftward to
advance an image field by field.
Joystick to R (B)/STEP ( ): Forward field
advance
Joystick to L (A)/STEP ( ): Backward field
advance
ec
The following are the operating procedures of the timelapse VCR via System Controller WV-CU360C/CJ.
Note: Index is unvaibable for time-lapse VCR.
TIME-LAPSE VCR CONTROL [NON-PANASONIC MODELS] (TERMINAL MODE)
● Fast-forward
A time-lapse VCR is operable with the system controller,
while connecting to the matrix switcher.
Refer to the time-lapse VCR’s operating instructions for how
to operate.
Notes:
• Before the use, it is necessary to install the
Multiplexer board in the matrix switcher, connect
the matrix switcher to the digital disk recorder, and
configure
the
system
through
WJ-SX150
Administrator Console, OSD SETUP MENU, and
time-lapse VCR's SETUP MENU. [Refer to p. 34
Installing the Multiplexer Board, p. 46 Connection
with the Time-lapse VCR (Non-Panasonic Models),
p. 52 WJ-SX150 SETUP MENU (OSD), and p. 64
WJ-SX150 ADMINISTRATOR CONSOLE.]
• You cannot display the setup menu of a time-lapse
VCR.
• You cannot control non-Panasonic time-lapse VCRs
from PS·Data system controllers.
● Rewind
y&
Fi
re
1. During the stop, press the REW button to rewind the
tape.
2. Press the STOP button to stop rewinding.
Note: Pressing the PLAY button during rewind will start
playback.
ur
it
The following is the procedure of a non-Panasonic model
time-lapse VCR.
● To Operate the Multiscreen Display
en
tS
The operations are the same as WJ-HD500 Series.
Refer to p. 117 Multiscreen Segment Switching.
ec
■ Controlling the Time-lapse VCR
● Manual Recording
● Normal Playback
te
llig
Refer to the time-lapse VCR’s operating instructions for how
to operate.
In
1. Enter the recorder mode. (Refer to p. 116 Recorder
Mode.)
2. Do the playback procedure using the buttons on the
front panel. (Refer to the time-lapse VCR’s operating
instructions for how to operate.)
3. Press the PLAY button. The playback image will appear
on the monitor.
4. To display the spot picture, press the numeric buttons
corresponding to the desired camera number, then
press the CAM [SET] button. Then, the active monitor
number with “-H**” (** is the camera number)” will
appear on the LED display. (Refer to p. 117 Normal
Playback for the illustration.)
123
WJ-HD500 SERIES CONTROL (PS·DATA)
This section will describe what you should take notice when using a PS·Data system controller.
The same descriptions as the system controller's operating instructions are not mentioned here. Refer to them.
Refer the descriptions of terminal mode for illustrations.
■ Controlling the Recorder with a PS·Data System Controller
● Recorder Mode
Before operating the recorder, it is necessary to enter the recorder mode.
Code
Forward field advance
1
Backward field advance
2
6
Stop recording and playback
8
Stop playback
9
Stop recording
10
Search forward
11
Search backward
12
Equal to the REC button of the recorder
Exclusive use to stop playback
19
Exclusive use to stop recording
Pressing again will hide the display.
llig
Displaying a recorder's OSD
ur
it
Recording
ec
5
tS
4
Playback
en
Pause
Note
y&
Function
Fi
re
1. Select the desired monitor. (Refer to p. 109 Monitor Selection.)
2. Enter "111" by pressing the numeric button.
"111" will appear on the LED display.
3. Press the CAM button.
The recorder image will be displayed on the selected monitor, and you will enter the recorder mode.
4. Enter the desired function code, and then press the FUNCTION button. (Refer to the diagram.)
te
5. To select a camera channel, press the numeric button(s), then CAM button. The system will exit from the recorder mode,
and the selected camera image will be displayed on the monitor.
In
Notes:
• Only one operator can enter the recording mode.
• The images from the recorder, which are displayed on the monitor, is conformed to the recorder setting.
124
WJ-HD100 SERIES CONTROL (PS·DATA)
This section will describe what you should take notice when using a PS·Data system controller.
The same descriptions as the system controller's operating instructions are not mentioned here. Refer to them.
Refer the descriptions of terminal mode for illustrations.
■ Controlling the Recorder with a PS·Data System Controller
● Recorder Mode
Before operating the recorder, it is necessary to enter the recorder mode.
Code
Forward field advance
1
Backward field advance
2
To the last field
3
Recording
6
To the first field
7
Stop recording and playback
8
Stop playback
9
Equal to the REC button of the recorder
10
en
Stop recording
ur
it
5
ec
4
Playback
tS
Pause
Note
y&
Function
Exclusive use to stop playback
Exclusive use to stop recording
11
Search backward
12
llig
Search forward
Fi
re
1. Select the desired monitor. (Refer to p. 109 Monitor Selection.)
2. Enter "111" by pressing the numeric button.
"111" will appear on the LED display.
3. Press the CAM button.
The recorder image will be displayed on the selected monitor, and you will enter the recorder mode.
4. Enter the desired function code, and then press the FUNCTION button. (Refer to the diagram.)
te
5. To select a camera channel, press the numeric button(s), then CAM button. The system will exit from the recorder mode,
and the selected camera image will be displayed on the monitor.
In
Notes:
• Only one operator can enter the recording mode.
• The images from the recorder, which are displayed on the monitor, is conformed to the recorder setting.
125
TIME-LAPSE VCR CONTROL (PS·DATA)
This section will describe what you should take notice when using a PS·Data system controller.
The same descriptions as those of digital disk recorders are not mentioned here. Refer to p.xx for details.
Notes:
• Before the use, it is necessary to install the Multiplexer board in the matrix switcher, connect the matrix switcher to the
time-lapse VCR, and configure the system through WJ-SX150 Administrator Console, OSD SETUP MENU, and time-lapse
VCR's SETUP MENU. [Refer to p. 34 Installing the Multiplexer Board, p. 45 Connection with the Time-lapse VCR
(Panasonic Models), p. 52 WJ-SX150 SETUP MENU (OSD), and p. 64 WJ-SX150 ADMINISTRATOR CONSOLE.]
• The time-lapse VCR's SETUP MENU cannot be displayed from a system controller.
Code
Forward field advance
1
2
Pause
4
Playback
5
Recording
6
Stop recording/playback
8
In
te
llig
en
tS
ec
ur
it
Backward field advance
y&
Function
Fi
re
■ Controlling the Time-lapse VCR with a PS·Data System Controller
126
MONITOR DISPLAY WHEN A VIDEO LOSS OCCURS
■ Video Loss Display
• When video loss of CAMERA IN nn (nn is a number) is
detected, " LOSS CH nn" will blink on the monitor.
• When more than one LOSS CH have occurred, "LOSS
CH nn*" will appear on the monitor.
LOSS CH01
LOSS CH01*
y&
ALL RESET
TOUR SEQ
REW/FF
PREV
NEXT
STEP
PAUSE
PLAY
PAUSE
T&D
CAM ID
EVENT
AUX1 ON
STILL
AUX1 OFF
MON STATUS
ALL
EL-ZOOM
AUX2 OFF
AUX2 ON
ALM H
VLD H
SYS S
SEQUENCE
DEF OFF
MON (ESC)
OSD
MON LOCK
DEF ON
CAM (SET)
MULTI SCREEN SEL
WIPER
llig
en
SHIFT
ec
SUSPEND
GROUP SEQ
ur
it
RESET
tS
ACK
te
■ Camera Switching Pulse Loss
Display
In
• When loss of the camera switching pulse is detected,
“SW LOSS” will blink on the monitor.
SW LOSS
• When the camera switching pulse is recovered, “SW
LOSS” will disappear from the monitor.
127
Fi
re
• When the input loss is recovered, "LOSS CH nn" will disappear from the monitor.
• When you press the RESET button while pressing the
"OSD"button, "LOSS CH nn" will disappear from the
monitor.
TROUBLESHOOTING
Check to see the following before request for repair.
If a trouble cannot be removed even after checking and trying remedy, contact your dealer.
Problem
Check item
Remedy
The power cord may be disconnected
either from the unit's power socket or
the AC outlet.
Connect the power cord between the
unit's power socket and the AC outlet.
System controller(s) do (does) not log
in.
The unit’s power cord may be disconnected from the AC outlet.
Connect the power cord to the AC outlet.
The cable connection(s) may be wrong
between the unit and the system controller(s).
Confirm the cable connections. (Refer
to p. 40.)
The mode selection switch setting of
the system controller may be wrong.
Confirm the mode selection switch setting. (Refer to p. 24.)
y&
Fi
re
Matrix switcher does not power up.
ec
ur
it
Data port setting may be wrong.
tS
Your ID, user number or password may
be wrong.
The monitor selection setting may be
wrong.
llig
en
Monitor is not selectable.
In
te
Camera image is not displayed even
after selecting the camera.
128
Open the Data Port window of WJSX150 Administrator Console (refer to
p. 81.) to select CU360 for the data
port. If 485 CAM is selected for the port,
the log-in will be invalid.
Refer to your Operator Registration
worksheet. Or open the Operator Registration window (refer to p. 75) and
reconfigure your ID, user number and
password.
Open the Monitor Selection window
(refer to p. 76) and confirm the setting.
If NG is assigned to your controller for
the monitor, the selection will be invalid.
The camera’s power cord connection
may be wrong.
Confirm the power cord connection.
(Refer to the camera’s operating
instructions.)
The cable connections may be wrong
between the unit and the camera.
Confirm the connections (pp. 37 to 39).
If the connections and camera type are
not correspondent, the camera image
will not appear.
The lens cover may not have been
removed from the camera.
Remove the lens cover from the camera.
The monitor's brightness or contrast
setting may not be proper.
Adjust the setting. (Refer to the monitor's operating instructions.)
Problem
Check item
The camera image is dim.
Dust may be sticking on the camera
lens.
Remove the dust from the camera lens.
The camera’s lens focus may not be
proper.
Press the FOCUS NEAR/ FAR buttons
to adjust the lens focus. If the camera
supports auto focus, press these buttons simultaneously. The lens focus can
be adjusted automatically.
The camera’s cable compensation setting may not be proper.
Open 710 COMPENSATION/VD2/DATA
(refer to p. 60) or the Cable Compensation/VD2 window (refer to p. 78) to confirm the setting.
The camera may not have been selected.
Select the camera again. (Refer to p.
91.)
The camera may not support the function you try to execute.
Confirm whether the camera supports
the function. (Refer to the camera's
operating instructions.)
The camera's cable setting may wrong.
Open 710 COMPENSATION/VD2/DATA
(refer to p. 60) or the Cable
Compensation/VD2/DATA (refer to p.
78) window to confirm the setting. If the
camera’s DATA is set to OFF, the RS485 cameras will not be operable.
ur
it
y&
Fi
re
The camera is not operable.
Remedy
ec
The data port setting may wrong.
• Select another camera.
• Wait until a higher-priority operator finishes controlling the camera.
While the PROHIBITED indicator is
lighting on the system controller, you
are prohibited to control the camera.
Open the Operator Registration window
(refer to p. 75) and reconfigure the setting.
en
tS
When the BUSY indicator is lighting on
the system controller, a higher-priority
operator has selected the camera.
In
te
llig
OSD items (Clock, Camera title, Monitor
status, Event) overlap one another.
Tour/group sequence is not activated.
129
Open the Data Port window (refer to p.
81) and confirm the setting.
• Turn off an overlapping item. (Refer to
p. 99.)
• Move OSD items. (Refer to p. 99.)
• Change the area title display position
through the camera’s setup menu.
(Refer to the camera’s operating
instructions.)
The tour/group sequence setting may
be wrong.
Open 300 SEQUENCE (refer to p. 55),
the Tour Sequence (refer to p. 68) or
Group Sequence (p. 69) window and
reconfigure the setting.
The setting has not been put from the
PC to the unit.
Put the configuration data to the unit
again after the configuration. (Refer to
p. 67 Put a File to SX150.)
When the PROHIBITED indicator is
lighting on the system controller, you
are prohibited to control the camera.
Open 800 OPERATOR REGISTRATION
(refer to p. 62) or the Operator
Registration window (refer to p. 75) and
reconfigure the setting.
Problem
Check item
The alarm mode is not activated.
Remedy
The alarm mode is set to OFF.
Set the alarm mode to SEQUENCE or
HOLD in SETUP MENU or WJ-SX150
Administrator Console.
SETUP MENU: Refer to p. 52.
Adminstrator Console: Refer to p. 64.
The port for an alarm input is set to
OFF.
Set the alarm port to ON in SETUP
MENU or WJ-SX150 Administrator
Console.
SETUP MENU: Refer to p. 52
Administrator Console: Refer to p. 64.
Press the ACK/SUSPEND button while
holding down the SHIFT button to cancel the alarm suspension.
SETUP MENU may be open.
Press the SETUP button while holding
down the SHIFT button to close SETUP
MENU.
Fi
re
When "ALM SUSPENDED" is displayed
on the monitor, the alarm is suspended.
You may not have selected the alarmrelated monitor.
y&
ACK or RESET is not activated.
ur
it
The system controller is not authorized
to select the monitor.
ec
You are not authorized to reset an
alarm.
en
tS
While the PROHIBITED indicator is
lighting on the system controller, you
are prohibited to control the monitor.
Timer event is not activated.
llig
In
te
SETUP MENU does not open.
A higher-priority operator may have
selected the event-related monitor.
The system does not enter the recording mode.
130
When the PROHIBITED indicator is lighting on the system controller, you are prohibited to open SETUP MENU.
Select the monitor again. (Refer to p.
90.)
Confirm the Monitor Selection window in
WJ-SX150 Administrator Console and
reconfigure the setting if necessary.
(Refer to p. 76.)
Confirm the Level Table window in WJSX150 Administrator Console and
reconfigure the setting if necessary.
(Refer to p. 76.)
Open the Level Table (refer to p. 76) or
Monitor Selection window (refer to p.
76) and reconfigure the setting if necessary.
Select another monitor.
Open the Level Table window (refer to
p. 76) and reconfigure the setting.
The recorder connection may be
wrong.
Connect the recommended recorder to
the unit.
The connected recorder may not conform to the unit.
Confirm the recorder connection (refer
to pp. 41 to 46.)
You are not authorized to operate the
recorder.
Open the Level Table window (refer to
p. 76) and reconfigure the setting.
131
tS
en
llig
te
In
ec
y&
ur
it
APPENDIX
Fi
re
COMMUNICATION PROTOCOL
The following pages detail the elements for communication between the unit and the PC.
When operating the PC, make sure to conform the serial port's communication speed to that of the unit.
The unit's communication speed is configurable by changing COM. SPEED in SETUP MENU. Data, parity and stop bits have
been set as follows:
Parameter
Data length
8bit(fixed)
Parity bit
NONE(fixed)
Stop bit
1bit(fixed)
Hardware flow control (ER/DR/RS/CS)
Not supported yet
Software flow control (Xon/Xoff)
Not supported yet
Wait Time
Not supported yet
Fi
re
Item
1. Transmission Command
Code
[STX] [Transmission Command] : [p1] : [p2] : : [pn] [ETX]
(02H) (
)–––––––––––––––––(
) (03H)
ur
it
ASCII
y&
The PC sends messages to the recorder in the following format. Also refer to the command table.
ec
[p] stands for parameter. Parameters are omitted when the command does not need to specify them.
2. Response Command
Code
[STX] [Response Command] : [p1] : [p2] : : [pn] [ETX]
(02H) (
)–––––––––––––––(
) (03H)
llig
ASCII
en
tS
The unit returns messages to the PC with the following formats.
(1) Reception Command
When the reception was completed successfully, the unit sends back the "ACK code 06H" to the PC, and then the
response command.
te
Parameters are omitted when the command format includes neither data nor status to send back.
In
(2) Reception Error
The unit sends back "NAK code 15H", followed by the parameters. The unit then resets the reception buffer and enters the
waiting mode for the next message. Parameter "e" identifies the error status.
Code
[NAK] [e]
ASCII
(15H)
1: Parity error (31H)
4: Overrun error (34H)
2: Overflow error (32H)
5: Timeout error (35H)
3: Framing error (33H)
(3) Parameter Error
The unit returns "ACK code 06H", if the transmission code was not processed properly, followed by an error code.
Code
[STX] [Response Command] : [E] [R] [n1] [n2] [n3] [ETX]
ASCII
(02H)
( )– – – – – – – – – – – – – (45H)
(52H) 03H
[n] stands for an error code number. (Refer to p. 141.)
Note: The unit returns [ACK] or [NAK] to the PC within 20 ms after the reception of [ETX] in a transmission.
132
■ Command Table
Basic Operation
Item
Transmission Command
(ASCII)
Log-in
Response (ASCII)
Parameter (ASCII)
CMD:Wnnnnn-ppppp
ANS:WOK (When OK)
ANS:WNG (When NG)
nnnnn= Operator number
ppppp= Password
Log-out
CMD:H00LG
ANS:H00LG
Monitor Selection
CMD:HmmMS
ANS:HmmMS
mm=Monitor No.
Camera Selection
CMD:HmmCScc
CMD:HmmCS+1
CMD:HmmCS-1
ANS:HmmCScc
ANS:HmmCS+1
ANS:HmmCS-1
mm=Monitor No.
cc=Camera No.
+1=To the next camera (Next)
-1=To the previous camera (Prev)
CMD:HmmSTnn
Starting group sequence
CMD:HmmSGn
ANS:HmmSGn
Pausing sequence
(PAUSE)
CMD:HmmSP
ANS:HmmSPn
Stopping sequence
(STOP)
CMD:HmmSO
ANS:HmmSO
Sequence increment
(NEXT)
CMD:HmmSI
ANS:HmmSI
Sequence decrement
(PREV)
CMD:HmmSD
Priority lock
CMD:HmmPR
OSD display ON / OFF
or
Moving OSD display position
CMD:Hmmss(o)
ur
it
y&
Starting tour sequence
133
mm=Monitor No.
mm=Monitor No.
Available only during sequence pause
Transmission command toggles priority lock
ON or OFF.
mm=Monitor No.
n=0 (OFF)
n=1 (ON)
ANS:HmmALn
Transmission command toggles OSD display
ON or OFF.
Use (o) parameter when moving OSD display position.
mm=Monitor No.
ec
ANS:HmmPRn
tS
en
llig
mm=Monitor No.
n=0 (SEQUENCE), 1 (PAUSE)
mm=Monitor No.
Available only during sequence pause
te
CMD: Hmmss
mm=Monitor No.
n=Group sequence No.
ANS:HmmSD
In
History or status display
ON/OFF
mm=Monitor No.
nn=Tour sequence No.
nn=00 Recorder sequence ON when the
recorder is selected.
Fi
re
ANS:HmmSTnn
ANS: Hmmssn
ss=AL
ss=TM
ss=TL
ss=TE
ss=TO
All OSD items ON/OFF
Time & date ON/OFF
Camera title ON/OFF
Event ON/OFF
Monitor status ON/OFF
o=U
o=D
o=L
o=R
Moving upward
Moving downward
Moving leftward
Moving rightward
n=0
n=1
Displayed
Not displayed
mm=Monitor No.
ss=DA Alarm history ON/OFF
ss=DV Video loss history ON/OFF
ss=DS System status ON/OFF
n=0
n=1
Displayed
Not displayed
Alarm Control
Item
Transmission Command
(ASCII)
Response (ASCII)
Parameter (ASCII)
Alarm input
OAIcc
No response
cc=Alarm No.
Alarm ACK
(Each monitor)
CMD:HmmAK
ANS:HmmAK
Alarm reset
(Each monitor)
CMD:HmmAR
ANS:HmmAR
Alarm all reset
CMD:H00AR
ANS:H00AR
Alarm suspension
MAD
MADn
Item
Transmission Command
(ASCII)
Response (ASCII)
Parameter (ASCII)
Display SETUP MENU
CMD:HmmSS
ANS:HmmSS
mm=Monitor No.
Return to normal view*
CMD:HmmSE
ANS:HmmSE
mm=Monitor No.
*Available only in SETUP MENU
Move the cursor leftward
CMD:AmmJL
—
mm=Monitor No.
Move the cursor rightward
CMD:AmmJR
—
Move the cursor upward
CMD:AmmJU
Move the cursor downward
CMD:AmmJD
Enter "0"
CMD:AmmT0
Enter "1"
CMD:AmmT1
Enter "2"
CMD:AmmT2
Enter "3"
mm=Monitor No.
Fi
re
Transmission command toggles alarm suspension ON or OFF.
n=0 OFF
n=1 ON
ec
ur
it
y&
Setup Control
—
mm=Monitor No.
mm=Monitor No.
mm=Monitor No.
—
mm=Monitor No.
—
mm=Monitor No.
—
mm=Monitor No.
CMD:AmmT3
—
mm=Monitor No.
Enter "4"
CMD:AmmT4
—
mm=Monitor No.
Enter "5"
CMD:AmmT5
—
mm=Monitor No.
Enter "6"
CMD:AmmT6
—
mm=Monitor No.
CMD:AmmT7
—
mm=Monitor No.
Enter "8"
CMD:AmmT8
—
mm=Monitor No.
Enter "9"
CMD:AmmT9
—
mm=Monitor No.
SET
CMD:AmmST
—
mm=Monitor No.
ESC
CMD:AmmES
—
mm=Monitor No.
INC
CMD:AmmIN
—
mm=Monitor No.
DEC
CMD:AmmDE
—
mm=Monitor No.
NEXT
CMD:AmmNX
—
mm=Monitor No.
Available in SETUP MENU, Alarm History
and Video Loss History
PRE
CMD:AmmPR
—
mm=Monitor No.
Available in SETUP MENU, Alarm History
and Video Loss History
In
te
llig
en
tS
—
Enter "7"
134
mm=Monitor No.
Camera Control
Transmission Command
(ASCII)
Response (ASCII)
Parameter (ASCII)
PAN/TILT
CMD:CmmPTccxxyy
—
mm=Monitor No.
cc=Camera No.
• Panning speed
xx=00 STOP
xx=01 to 40(HEX) + direction panning
(Max is 40 and min is 01)
xx=81 to C0(HEX) - direction panning
(Max is C0 and min is 81)
• Tilting speed
yy=00 STOP
yy=01 to 40(HEX) + direction tilting
(Max is 40 and min is 01)
yy=81 to C0(HEX) - direction tilting
(Max is C0 and min is 81)
Zoom
CMD:CmmZMccn
—
Focus
CMD:CmmFCccn
—
Iris
CMD:CmmIRccn
ec
ur
it
y&
Fi
re
Item
In
te
llig
en
tS
—
135
mm=Monitor No.
cc=Camera No.
n=0 STOP
n=1 TELE
n=2 WIDE
mm=Monitor No.
cc=Camera No.
n=0 STOP
1 NEAR
2 FAR
3 AUTO FOCUS
mm=Monitor No.
cc=Camera No.
n=0 STOP
n=1 OPEN
n=2 CLOSE
n=3 AUTO IRIS
Item
Transmission Command
(ASCII)
Response (ASCII)
Parameter (ASCII)
Camera's SETUP MENU
CMD:CmmCMccn
—
mm=Monitor No.
cc=Camera No.
n=0 OFF
n=1 ON
Program Preset Position
CMD:CmmPSccnn
—
Color/BW
CMD:CmmBWccn
—
Patrol
CMD:CmmPAccn
Camera Function
CMD:CmmCFccnnn
Auto Panning
CMD:CmmAPccn
mm=Monitor No.
cc=Camera No.
nn=01 to 64 Preset position No.
nn=00 Home position
y&
—
ur
it
CMD:CmmPMccnn
ec
Call Preset Position
Fi
re
The following commands are available in
SETUP MENU:
CMD:AmmJL (Move the cursor leftward)
CMD:AmmJR (Move the cursor rightward)
CMD:AmmJU (Move the cursor upward)
CMD:AmmJD (Move the cursor downward)
CMD:AmmST (SET)
CMD:AmmES (ESC)
CMD:AmmIN (RESET)
CMD:AmmDE (ALL RESET)
en
tS
—
mm=Monitor No.
cc=Camera No.
n=0 OFF (Color)
n=1 ON (BW)
mm=Monitor No.
cc=Camera No.
n=0 STOP
n=1 PLAY
n=2 LEARN
mm=Monitor No.
cc=Camera No.
nnn=Camera function No. (001 to 256)
—
mm=Monitor No.
cc=Camera No.
n=0 AUTO PAN
n=1 AUTO SORT
n=2 AUTO SEQ
CMD:CmmWPccn
—
mm=Monitor No.
cc=Camera No.
n=0 OFF
n=1 ON
Defroster
CMD:CmmDFccn
—
mm=Monitor No.
cc=Camera No.
n=0 OFF
n=1 ON
AUX1
CMD:CmmA1ccn
—
mm=Monitor No.
cc=Camera No.
n=0 OFF
n=1 ON
AUX2
CMD:CmmA2ccn
—
mm=Monitor No.
cc=Camera No.
n=0 OFF
n=1 ON
In
te
llig
—
Wiper
136
mm=Monitor No.
cc=Camera No.
nn=01 to 64 Preset position No.
Recorder Control
Item
Transmission Command
(ASCII)
Response (ASCII)
Parameter (ASCII)
Recorder button
CMD:HmmRS
ANS:HmmRS
Playback images of HD500 Series appear on
the monitor. (Recorder mode)
To cancel the recorder mode, enter the STOP
command, then Camera Selection command.
(Refer to p. 107).
Multiscreen segment switching
CMD:RmmML
ANS:RmmML
mm=Monitor No.
Electronic Zoom
CMD:RmmZM
ANS:RmmZMn
Transmission command toggles zoom.
Fi
re
mm=Monitor No.
n=0 Zoom OFF
n=1 + mark display ON
n=2 Two-fold zoom
n=4 x4Live image/Playback image
n=8 x8Live image/Playback image
ANS:RmmVSn
y&
CMD:RmmVS
ec
ur
it
Live/Playback image
Pause
CMD:RmmPA
Stop
CMD:RmmSPn
Transmission command changes the monitor
display between live and playback image.
n=0 Live image
n=1 Playback image
ANS:RmmPL
mm=Monitor No.
ANS:RmmPA
mm=Monitor No.
tS
CMD:RmmPL
ANS:RmmSPn
mm=Monitor No.
n=0 Stop playback
n=1 Stop recording
In
te
llig
en
Play
Necessary when using a non-Panasonic
recorder with the Multiplexer board.
137
137
Item
Transmission Command
(ASCII)
Response (ASCII)
Parameter (ASCII)
Still display
CMD:RmmSTcc
ANS:RmmSTccn
Available only with the Multiplexer
Transmission command toggles still display
ON or OFF.
mm=Monitor No.
cc=Camera No.
(cc=00 when toggling multiscreen still ON or
OFF)
n=0 OFF
n=1 ON
CMD:RmmFF
ANS:RmmFF
mm=Monitor No.
REW
CMD:RmmRW
ANS:RmmRW
mm=Monitor No.
Forward field advance
CMD:RmmFA
ANS:RmmFA
mm=Monitor No.
Backward field advance
CMD:RmmRA
ANS:RmmRA
mm=Monitor No.
Record
CMD:RmmRC
ANS:RmmRC
Index
CMD:RmmSC
ANS:RmmSC
CMD:RmmTMn
ANS:RmmTMn
llig
CMD:RmmTG
ANS:RmmTG
In
Alarm search
CMD:RmmAS
mm=Monitor No.
mm=Monitor No.
Transmission command changes the monitor
display between index and live image.
Setup control commands (refer to p. 134) are
available while the index is displayed.
Available only for Record List and
Thumbnail Display of WJ-HD500 Series
Transmission command toggles search editing area ON/OFF, or starts search.
mm=Monitor No.
n=0 OFF
n=1 ON
n=2 Search start
Available only for Record List and
Thumbnail Display of WJ-HD500 Series
Transmission command selects group to be
displayed.
mm=Monitor No.
te
Group select
en
tS
ec
Search editing area
ur
it
y&
Fi
re
FF
ANS:RmmAS
Available only for Record List and
Thumbnail Display of WJ-HD500 Series
Transmission command toggles alarm search
ON or OFF.
mm=Monitor No.
n=0 OFF
n=1 ON
138
Inquiry
Item
Transmission Command
(ASCII)
Response (ASCII)
Parameter (ASCII)
Model No
QID
qid:WJ-SX150
Matrix switcher's model No.
Software version
QRV
qrv:*.**
qrv:*.**/*.**
*.**=Matrix switcher's software version
*.**/*.**: Matrix switcher’s software version/Multiplexer board’s version
Alarm history
QAD
qad:nnn:YYYYMMDD
hhmmss:cc:ee:s
nnn=alarm-event total number
(000 to 100)
*=Event of alarm n (n is a number).
Display pattern:
YYYYMMDDhhmmss:cc:ee:s
qvd:nnn: YYYYMMDD
hhmmss:cc:ee:s
QVD
In
te
llig
en
Video loss history
tS
ec
ur
it
y&
Fi
re
YYYY=Year
MM=Month
DD=Day
hh=Hour
mm= Month
ss=Second
cc=Alarm number (associated with the camera number: 00 when the alarm is suspended)
ee= Event
00=ALARM
01=ACK
02=RESET
s=Daylight saving time (summer time)
0=OFF
1=ON
139
nnn=video-loss total number
(000 to 100)
*=Event of video loss n (n is a number).
Display pattern:
YYYYMMDDhhmmss:cc:ee:s
YYYY=Year
MM=Month
DD=Day
hh=Hour
mm= Month
ss=Second
cc=Video loss number (associated with the
camera number: 00 in case of camera
switching pulse loss/recovery)
ee= Event
00=Video loss
01=Video loss recovery
02=Camera switching loss
03=Camera switching recovery
s=Daylight saving time (summer time)
0=OFF
1=ON
Miscellaneous Control
Item
Transmission Command
(ASCII)
Alarm display
–
Response (ASCII)
Parameter (ASCII)
In
te
llig
en
tS
ec
ur
it
y&
Fi
re
ALM:cc:a:yyyymmdd:hhmm a=Event
ss:b
0=ALARM
1=ACK
2=RESET
yyyy=Year
mm=Month
dd=Day
hh=Hour
ss=Second
b=Daylight saving time (summer time)
0=OFF
1=ON
140
■ Error Code List
● Matrix switcher and external devices
Error code(ASCII)
Error type
Meaning
ER000
No error
There is no error.
ER001
No associated command
There is no associated command.
ER002
Parameter invalid
The parameter's number, digit and range are invalid.
ER003
Receiver buffer's overflow
The receiver buffer has reached overflow capacity.
● Matrix switcher and external devices
Error type
Meaning
ER301
Command invalid
Invalid operation mode caused the command error.
ER302
Parameter invalid
The parameter's number, digit and range are valid, but the operation mode
Fi
re
Error code(ASCII)
is invalid.
ER303
Gateway reception overflow
Reception buffer overflow has occurred on the other device during the
y&
gateway communication.
Gateway timeout error
Timeout error has occurred during the gateway communication.
ER309
Internal error
The internal processing error has happened.
ur
it
ER305
In
te
llig
en
tS
ec
Example: The command is valid but it cannot be executed.
(1) The unit receives the zoom command while selecting a camera without electronic zoom function.
Transmission Command (ASCII)
[STX] CMD:R01ZM [ETX]
Transmission Command (ASCII)
[STX] ANS:R01ZM:ER301 [ETX]
141
WORKSHEETS
Gathering information for the initial configuration and recording on the following worksheets are recommended. Then, if settings need to be modified or updated later because of a change in surveillance needs or changes made in the system's components, those worksheets can be used to track revisions to your system.
You should keep all revised worksheets. Be sure to date them, in preparation for new entry or troubleshooting. Regardless of
the system size, the worksheets can track past, current, and future configurations.
■ Instruction
y&
Fi
re
Each worksheet's title is the same as that of WJ-SX150 Administrator Console.
For example, the "Operator Registration" worksheet supports the "Operator Registration" window.
The worksheets' rows, columns, and fields are arranged to match WJ-SX150 Administrator Console configuration requirements.
1. Reproduce the worksheets. You may need dozens of copies.
2. Reproduce instructions for the configuration windows . You can attach the portions of instructions to the worksheets.
To keep record of the initial configuration of the system, date the "Data Completed" line on the top left of each sheet.
■ Team Work
In
te
llig
en
tS
ec
ur
it
Worksheets are arranged alphabetically on the following pages, to make them easy to find.
For a team approach to information collection, decide how to distribute worksheets/tasks among several individuals.
142
■ Checklist
It is recommended that the worksheets be completed in the following sequence:
Date completed: ___/ ___/ ___
● Recorder
Built in multiplexer board
Recorder Control
Unit Address
EXT IN
Yes/No
OFF/HD100/HD200/HD500/VCR
Genlock off/on
143
Camera
Preset position
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Camera
Preset position
Dwell time
Tour __ / 16
Remark
In
te
llig
en
tS
ec
ur
it
y&
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Fi
re
● Tour Sequence
Dwell time
Tour __ / 16
Remark
Preset position
Dwell time
Monitor 2
Monitor 3
Fi
re
Camera
y&
Step
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ec
tS
In
te
llig
en
Monitor 1
ur
it
● Group Sequence
Group
1
2
3
4
144
Tour __ / 16
Remark
Monitor 4
● Timer Event
Schdule
Mode
Daily
Weekly
Action
Monthly
Tour Sequence
Spot Camera
Every
Every
Hour
Sunday
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Every Day#
Monitor#
Camera#
Minute
Fi
re
Tour#
Preset Position#
Daily
Weekly
Every
Every
Hour
Sunday
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Day#
Minute
Every
Cam #5
Cam #6
Cam #7
Cam #8
Cam #9
Cam #10
Cam #11
Cam #12
Start
145
In
● Daylight Saving Time
te
llig
en
tS
Monthly
Auto Cleaning Cam #1
Camera
Cam #2
Cam #3
Cam #4
ec
ur
it
Schdule
Mode
y&
● Camera Auto Cleaning
End
Start
End
Cam #13
Cam #14
Cam #15
Cam #16
● Alarm Mode
Alarm Mode
OFF
Sequence Mode
Hold Mode
Dwell
Alarm Input
Camera Site Alarm
Alarm Port
Serial Port
Mux Motion Det
sec.
Auto Reset Time
OFF / ON / REC only
OFF / ON / REC only
OFF / ON / REC only
OFF / ON / REC only
sec.
● Alarm Event
Monitor#
Camera# / Tour sequence#
Preset position#
Fi
re
ALM#
1
2
3
4
tS
ec
ur
it
y&
5
6
7
8
9
10
11
12
13
14
15
146
te
Alarm #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Alarm Port
N.O./N.C./Time
N.O./N.C./Time
N.O./N.C./Time
N.O./N.C./Time
N.O./N.C./Time
N.O./N.C./Time
N.O./N.C./Time
N.O./N.C./Time
N.O./N.C./Time
N.O./N.C./Time
N.O./N.C./Time
N.O./N.C./Time
N.O./N.C./Time
N.O./N.C./Time
N.O./N.C./Time
N.O./N.C./Time
In
● Alarm Port
llig
en
16
● Operator Registration
—
Password
Level
Priority
—
—
1
1
Camera Access
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
— — — — — — — — — — — — — — — —
Fi
re
Timer
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ID
y&
Operator#
ur
it
Camera Access
1: View & Control 2: View Only 3: Prohibited
Level 2
Level 3
te
llig
en
tS
Level 1
In
Control
SX150 Setup
Camera Setup
Alarm History Display
Video Loss History Display
System Status Display
Single Alarm Reset
All Alarm Reset
Alarm Suspend
Camera View
Call Sequence
Program Preset Position
OSD Control
Camera Control
Recorder Control
Recorder Setup
ec
● Level Table
● Monitor Selection
Controller 1(KB1)
Controller 2(KB2)
Controller 3(KB3)
Controller 4(KB4)
PC
147
Monitor 1
OK / NG
OK / NG
OK / NG
OK / NG
OK / NG
Monitor 2
OK / NG
OK / NG
OK / NG
OK / NG
OK / NG
Monitor 3
OK / NG
OK / NG
OK / NG
OK / NG
OK / NG
Monitor 4
OK / NG
OK / NG
OK / NG
OK / NG
OK / NG
● Auto Log-in/Log-out
Auto Log-in
Auto Log-out
DATA 1
DATA 2
DATA 3
DATA 4
DATA 1
DATA 2
DATA 3
DATA 4
Minute(s)
● Cable Compensation/VD2
tS
en
● Camera Title
148
In
te
llig
Camera ID (Up to 20 characters)
Cam 1
Cam 2
Cam 3
Cam 4
Cam 5
Cam 6
Cam 7
Cam 8
Cam 9
Cam 10
Cam 11
Cam 12
Cam 13
Cam 14
Cam 15
Cam 16
Fi
re
DATA
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
y&
VD2
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ur
it
Cable Compensation
S/M/L
S/M/L
S/M/L
S/M/L
S/M/L
S/M/L
S/M/L
S/M/L
S/M/L
S/M/L
S/M/L
S/M/L
S/M/L
S/M/L
S/M/L
S/M/L
ec
Camera #
Cam 1
Cam 2
Cam 3
Cam 4
Cam 5
Cam 6
Cam 7
Cam 8
Cam 9
Cam 10
Cam 11
Cam 12
Cam 13
Cam 14
Cam 15
Cam 16
● Data Port
RS485 Port
RS485
DATA 1
DATA 2
DATA 3
DATA 4
Protocol
485 CAM
485 CAM/CU360C
485 CAM/CU360C
485 CAM/CU360C
CU360C/PS•Data
Baud Rate
bps
bps
bps
bps
bps
RS485
Camera
Daisy
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16
Fi
re
PS•Data mode (for DATA 4)
sec.
Logout Time
sec.
Alarm Data
Wait Time
Group Address
REC Out (Normal)
REC MODE
EXT
INT
In
te
llig
149
ur
it
en
Title Display
Clock Display
s
ec
Quad / 3+1 / 8+1
tS
Multi Monitor Out
Still Display
Border Color
Quad Shift
Secret View
Sequence Mode
y&
● Multiplexer
Fields
REC Out (Alarm)
REC MODE
EXT
INT
OFF / ALM-PRI / ALM-ONLY / GROUP
Dynamic REC
GROUP
Cam
Cam
Cam
Fields
Cam
ur
it
y&
Fi
re
ALM 1
ALM 2
ALM 3
ALM 4
ALM 5
ALM 6
ALM 7
ALM 8
ALM 9
ALM 10
ALM 11
ALM 12
ALM 13
ALM 14
ALM 15
ALM 16
In
te
llig
Multiplexer Board Camera Title
Cam1
Cam2
Cam3
Cam4
Cam5
Cam6
Cam7
Cam8
Cam9
Cam10
Cam11
Cam12
Cam13
Cam14
Cam15
Cam16
en
tS
ec
System
Camera SW Loss
Dummy Black
150
SPECIFICATIONS
Power Source:
Power Consumption:
Camera Input (1 to 16):
120 V AC, 60 Hz
60 W
1.0 V[p-p]/75 Ω composite video signal
0.5 V[p-p]/75 Ω data signal and 2.5 V[p-p]/75 Ω vertical timing pulse multiplexed
1.0 V[p-p]/75 Ω composite video signal
1.0 V[p-p]/75 Ω composite video signal
1.0 V[p-p]/75 Ω composite video signal
1.0 V[p-p]/75 Ω composite video signal
RS-485 6-conductor modular jack
RS-485 6-conductor modular jack
25-pin D-sub connector
9-pin D-sub connector
RCA pin jack
–10 °C to +50 °C (14 °F to 122 °F)
Less than 90 %
420 mm (W) X 88 mm (H) X 350 mm (D)
[16-9/16" (W) X 3-7/16" (H) X 13-3/4" (D)]
6 kg (13.2 lbs.)
Fi
re
Camera Output (1 to 16):
Monitor Output (1 to 4):
External Input:
External Output:
RS-485 (Camera) Port:
Data Port:
Alarm Port:
Serial Port:
Camera Switching Input:
Ambient Operating Temperature:
Ambient Operating Humidity:
Dimensions:
In
te
llig
en
tS
ec
ur
it
y&
Weight:
STANDARD ACCESSORIES
Rack Mounting Bracket ................................... 2 pcs.
Screws (M4 x 10) ............................................ 4 pcs.
Power Cable .................................................... 1 pc.
CD-ROM .......................................................... 1 pc.
151
Fi
re
y&
ur
it
ec
tS
en
llig
te
In
Panasonic Digital Communications & Security Company
Unit Company of Matsushita Electric Corporation of America
Security Systems
www.panasonic.com/cctv
Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094
Zone Office
Eastern: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303
Central: 1707 N.Randal Road, Elgin, IL 60123 (847) 468-5205
Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840
2002
© Matsushita Communication Industrial Co., Ltd. All rights reserved.
PANASONIC CANADA INC.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada (905)624-5010
PANASONIC SALES COMPANY
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC.
San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina,
P.R. 00985 (809)750-4300
NM0102-4112
V8QB5945EN
Printed in Japan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement