- No category
advertisement
Installation Instructions
DOMINATOR D4 DUAL-STEP
Part # D44046
2001-2006
2011-2013
Chevrolet Silverado & GMC Sierra
Chevrolet Silverado & GMC Sierra
1500, 2500HD, 3500 Crew Cab
2500HD, 3500HD Crew Cab (Diesel Only)
Parts List
Item Qty. Part # Description
1 1 Pr 391014AA Front Mounting Bracket
11
12
13
14
8
9
10
15
16
17
18
19
2
3
4
5
6
7
6
6
6
6
18
18
18
6
1
6
6
1
1 Pr 391014DA Middle Mounting Bracket
1 Pr 391014BA Rear Mounting Bracket
2 Pr 391014FA Front & Middle Auxiliary Bracket
1 pr 391014EA Rear Auxiliary Bracket
6 3713312 5/16” Bolt Plate
12 - 5/16” Square Head Bolt
-
-
-
-
-
-
-
-
-
-
5/16” Flat Washer
5/16” Lock Washer
5/16” Hex Nut
3/8” 1” Carriage Bolt
3/8” Flat Washer
3/8” Lock Washer
3/8” Hex Nut
M12 x 12mm Hex Bolt
½” Lock Washer
½” Flat Washer
D44046D Driver Side Step
D44046P Passenger Side Step
Torque
-
-
-
-
-
-
11Ft. Lbs.
-
-
11Ft. Lbs.
30 Ft. Lbs.
-
-
30 Ft. Lbs.
70 Ft. Lbs.
-
-
-
-
Tool Required:
½”, 9/16”, 18mm, 19mm & 21mm Socket
17mm (12 point) Socket
15mm, 1/2” & 9/16” Wrench
Ratchet & Ratchet Extension
Approximate Installation Time: 45 min
Read the installation instructions completely and verify that all of the parts listed are accounted for. If you have defective, missing or damaged parts or need assistance, please contact Go Rhino Products for fast, friendly customer service at: 1-888-427-4466 or email: [email protected]
WARNING! GM uses thread-locking compound on all factory body mount bolts. Removal using an air assisted impact or ratchet will damage the body mount bolt threads and the internal nut assembly.
We only recommend using hand tools to slowly remove and reinstall body mount bolts on all GM vehicles.
IMPORTANT! If during the body mount bolt removal process, it becomes increasingly difficult to unscrew the bolt with hand tools, tighten the bolt several rotations to clear the thread-locking compound from the threads, then reverse the direction and continue to unscrew the bolt until it is out. Repeat this process as necessary on all of the body mount bolts. Use of an appropriate anti-seize compound is highly recommended for re-installation. Tighten the body mount bolts to factory torque specifications for your particular model year.
NOTE: The parts kit may include additional fastener that will not be used for this application.
1
Installation
Step-1 Begin the installation by removing the passenger side front body mount bolt. Picture #1
Keep all existing washers and bushing in place, and attach the front bracket to the vehicle using the factory body mount bolt or one of the supplied 12mm hex bolts depending on the model year of you vehicle. Leave the bolt loose for final adjustment.
Illustration #1
NOTE: For model year 2006 and up, use the factory body mounting bolts.
Step-2 Locate the obround hole in the underside of the body and install one of the 5/16” bolt plates. Picture #1
Attach the passenger side front auxiliary bracket to the body using the bolt plate, (1) 5/16” flat washer, (1) 5/16” lock washer and (1) 5/16” hex nut. Attach the opposite end of the auxiliary bracket to the side of the front bracket using (1) 3/8” x 1” carriage bolt, (1) 3/8” flat washer, (1) 3/8” lock washer and (1) 3/8” hex nut. Leave the nuts and bolts loose for final adjustment.
Illustration #1
Illustration #1
Passenger
Side Front
Front Body Mount Bolt, Passenger Side
Picture #1
Passenger
Side Front
Install 5/16” Bolt Plate
Step-3 Remove the passenger side middle body mount bolt. Picture #2
Keep all existing washers and bushing in place, and attach the front bracket to the vehicle using the factory body mount bolt or one of the supplied 12mm hex bolts depending on the model year of you vehicle. Leave the bolt loose for final adjustment.
Illustration #2
Step-4 Locate the obround hole in the underside of the body and install one of the 5/16” bolt plates. Picture #2
Attach the passenger side middle auxiliary bracket to the body using the bolt plate, (1) 5/16” flat washer, (1) 5/16” lock washer and (1) 5/16” hex nut. Attach the opposite end of the auxiliary bracket to the side of the middle bracket using (1) 3/8” x 1” carriage bolt, (1) 3/8” flat washer, (1) 3/8” lock washer and (1) 3/8” hex nut. Leave the nuts and bolts loose for final adjustment.
Illustration #2
Install 5/16” Bolt Plate
Picture #2
Passenger
Side Middle
Middle Body Mount Bolt, Passenger Side
Illustration #2
Passenger
Side Middle
2
Step-5 Remove the passenger side rear body mount bolt. Picture #3
Keep all existing washers and bushing in place, and attach the front bracket to the vehicle using the factory body mount bolt or one of the supplied 12mm hex bolts depending on the model year of you vehicle. Leave the bolt loose for final adjustment.
Illustration #3
Step-6 Locate and remove the plastic plug in the body rocker panel to expose the round hole, and install one of the 5/16” bolt plates.
Picture #3
Attach the passenger side rear auxiliary bracket to the body rocker panel using the bolt plate, (1) 5/16” flat washer, (1) 5/16” lock washer and (1) 5/16” hex nut. Attach the opposite end of the auxiliary bracket to the side of the rear bracket using (1)
3/8” x 1” carriage bolt, (1) 3/8” flat washer, (1) 3/8” lock washer and (1) 3/8” hex nut. Leave the nuts and bolts loose for final adjustment.
Illustration #3
Install 5/16” Bolt Plate
Picture #3
Passenger
Side Rear
Illustration #3
Passenger
Side Rear
Rear Body Mount Bolt, Passenger Side
Step-7 Attach the passenger side step to each of the brackets using (2) 5/16” x 1” square head bolts, (2) 5/16” flat washers and (2) 5/16” lock washers as shown. Illustration #4 & #5
Step-8 Align the side step with the vehicle and tighten all side step and mounting bracket nuts and bolts. Repeat the installation steps to install the driver side brackets and side step. Remember to check and retighten all nuts and bolts periodically.
Illustration #5
Illustration #4
Passenger
Side Front
3
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project