Weslo Cadence S5 Treadmill User`s manual

Weslo Cadence S5 Treadmill User`s manual
ORDERING REPLACEMENT PARTS
To order replacement parts, contact the ICON Health & Fitness, Ltd. office, or write:
ICON Health & Fitness, Ltd.
Customer Service Department
Unit 4, Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
Model No. WETL13906.0
Serial No.
Serial Number
Decal
Tel:
08457 089 009
Outside the UK: (44) 0113 387 7133
Fax: (44) 0113 387 7125
To help us assist you, please be prepared to provide the following information:
• the MODEL NUMBER of the product (WETL13906.0)
QUESTIONS?
• the NAME of the product (WESLO CADENCE S5 treadmill)
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts,
please call:
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the needed part(s) (see the PART LIST and the EXPLODED
DRAWING in the centre of this manual)
08457 089 009
or write:
ICON Health & Fitness, Ltd.
Customer Service Department
Unit 4
Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
email: [email protected]
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Part No. 237158 R0306A
Printed in China © 2006 ICON IP, Inc.
USER'S MANUAL
CONDITIONING GUIDELINES
is to burn fat, adjust the speed and incline of the treadmill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: A PART IDENTIFICATION CHART, an EXPLODED DRAWING, and a PART LIST are attached in the
center of this manual.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
WORKOUT GUIDELINES
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “training zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent postexercise problems.
EXERCISE FREQUENCY
Fat Burning
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for energy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
WESLO is a registered trademark of ICON IP, Inc.
2
19
PROBLEM: The walking belt slows when walked on
IMPORTANT PRECAUTIONS
SOLUTION: a. If an extension cord is needed, use only a 3-conductor, 1mm (14-gauge) cord that is no longer
than 1.5 m (5 ft.).
2
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller bolts counterclockwise, 1/4 of a turn. When
the walking belt is properly tightened, you should be
able to lift each edge of the walking belt 5 to 7 cm (2
to 3 in.) off the walking platform. Be careful to keep
the walking belt centered. Then, plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is properly
tightened.
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
b
5–7cm
Rear Roller
Bolts
c. If the walking belt still slows when walked on, please see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt has shifted to the left, first remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller bolt
clockwise 1/2 of a turn. Be careful not to overtighten
the walking belt. If the walking belt has shifted to
the right, turn the left rear roller bolt counterclockwise
1/2 of a turn. Then, plug in the power cord, insert the
key, and run the treadmill for a few minutes. Repeat
until the walking belt is centered.
b. If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn both rear roller bolts
clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge
of the walking belt 5 to 7 cm (2 to 3 in.) off the walking
platform. Be careful to keep the walking belt centered.
Then, plug in the power cord, insert the key, and
carefully walk on the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
a
b
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
11. If an extension cord is needed, use only a 3conductor, 1mm2 (14-gauge) cord that is no
longer than 1.5 m (5 ft.).
2. Use the treadmill only as described in this
manual.
12. Keep the power cord away from heated surfaces.
3. Place the treadmill on a level surface, with at
least 2.5 m (8 ft.) of clearance behind it and
0.5 m (2 ft.) on each side. Do not place the
treadmill on a surface that blocks any air
openings. To protect the floor or carpet from
damage, place a mat under the treadmill.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See MAINTENANCE AND TROUBLESHOOTING on page
17 if the treadmill is not working properly.)
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Read, understand, and test the emergency
stop procedure before using the treadmill (see
OPERATION AND ADJUSTMENT on page 10).
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
7. The treadmill should be used only by persons
weighing 113 kg (250 lbs.) or less.
17. Never leave the treadmill unattended while it is
running. Always remove the key and unplug
the power cord when the treadmill is not in use.
8. Never allow more than one person on the
treadmill at a time.
18. The pulse sensor is not a medical device.
Various factors, including your movement, may
affect the accuracy of heart rate readings. The
pulse sensor is intended only as an exercise
aid in determining heart rate trends in general.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes; never use the treadmill with bare feet,
wearing only stockings, or in sandals.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 15.)
You must be able to safely lift 20 kg (45 lbs.) to
raise, lower, or move the treadmill.
10. When connecting the power cord (see page
10), plug the power cord into an earthed circuit. No other appliance should be on the
same circuit. When replacing the fuse, an
ASTA approved BS1362 type should be fitted
to the fuse carrier. A 13 amp fuse should be
used.
18
20. When folding or moving the treadmill, make
sure that the frame is securely held by the
lock pin.
3
21. Do not change the incline of the treadmill by
placing objects under the treadmill.
tenance and adjustment procedures described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
22. Inspect and properly tighten all parts of the
treadmill regularly.
23. Never drop or insert any object into any
opening.
24.
25. This treadmill is intended for in-home use
only. Do not use this treadmill in any commercial, rental, or institutional setting.
DANGER: Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
MAINTENANCE AND TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet (see page 10). If an extension cord is needed, use only a 3-conductor, 1 mm2 (14-gauge) cord that is no longer than 1.5 m
(5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
c. Check the circuit breaker located on the treadmill
near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
d. Check the on/off switch located on the treadmill
near the power cord. The switch must be in the “on”
position.
The decal shown at the right has been placed on the
treadmill. If the decal is missing, or if it is not legible,
call the toll-free telephone number on the front cover of
this manual and order a free replacement decal. Apply
the decal in the location shown. Note: The decal is not
shown at actual size.
c
Tripped
Reset
d
On
Position
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill near the power cord (see c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. Make sure that the on/off switch is in the “on” position (see d. above).
e. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. Remove the five indicated Screws
(20) and the two Foot Rail Screws (25). Then, carefully remove the Hood (65).
a
65
20
20
20
25
Hungarian
232971
Russian
Polish
4
Portugese
English:
Locate the Reed Switch (97) and the Magnet (113) on
the left side of the Pulley (104). Turn the Pulley until
the Magnet is aligned with the Reed Switch. Make
sure that the gap between the Magnet and the
Reed Switch is about 3 mm (1/8 in.). If necessary,
loosen the Screw (21), move the Reed Switch slightly,
and then retighten the Screw. Reattach the Hood, and
run the treadmill for a few minutes to check for a correct speed reading.
17
3 mm
21
97
Top View
104
113
HOW TO LOWER THE TREADMILL FOR USE
BEFORE YOU BEGIN
1. Hold the upper end of the treadmill with your right hand as
shown. Using your left hand, pull the latch knob to the left
and hold it. Next, lower the frame until it is past the latch
pin. Then, release the latch knob.
Latch
Pin
Latch
Knob
Catch
Thank you for selecting the new WESLO® CADENCE
S5 treadmill. The CADENCE S5 treadmill combines
advanced technology with innovative design to make
your workouts at home more effective and enjoyable.
And when you’re not exercising, the CADENCE S5
treadmill can be folded up, requiring less than half the
floor space of other treadmills.
ing this manual, please see the front cover of this manual. To help us assist you, please note the product
model number and serial number before contacting us.
The model number of the treadmill is WETL13906.0.
The serial number can be found on a decal attached to
the treadmill (see the front cover of this manual for the
location).
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Before reading further, please familiarise yourself with
the parts that are labelled in the drawing below.
2. Hold the frame firmly with both hands, and lower it to the
floor. To decrease the possibility of injury, bend your
legs and keep your back straight.
Water Bottle Holder
(Bottle is not included)
Console
Handrail
Key/Clip
Storage Latch
Hood
Walking Belt
On/Off Switch
Circuit Breaker
Foot Rail
Wheel
RIGHT SIDE
Incline Leg/Pin
Rear Roller
Adjustment Bolts
16
5
HOW TO FOLD AND MOVE THE TREADMILL
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to
the top of the walking belt or the shipping carton. This does not affect treadmill performance. If there is lubricant
on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
HOW TO FOLD THE TREADMILL FOR STORAGE
In addition to the included hex key
, assembly requires a phillips screwdriver
spanners
, and wire cutters
.
1. Hold the metal frame firmly in the location shown by
the arrow at the right. CAUTION: To decrease the possibility of injury, do not lift the frame by the plastic
foot rails. Make sure to bend your legs and keep your
back straight. As you raise the frame, make sure to lift
with your legs rather than your back. Raise the frame
about halfway to the vertical position.
, two
Note: To identify small parts used during assembly, see the PART IDENTIFICATION CHART in the center of
this manual. Some parts may be preassembled.
1. Have a second person hold the Base (52) in the position
shown.
1
52
Identify the Left Upright (53) (the Right Upright [54] has a
large hole near the lower end).
16
54
Hold the Left Upright (53) so the bend is in the position shown. Insert two Upright Bolts (2) into the
bracket on the Left Upright. Attach the Left Upright to
the Base (52) with the Upright Bolts and two Upright Nuts
(16). Do not tighten the Upright Nuts yet.
Large
Hole
16
2
Frame
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob
to the left and hold it. Raise the frame until the catch is
past the latch pin. Then, slowly release the latch knob;
make sure that the latch pin is resting against the
catch.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in temperatures above 30°C (85°F).
53
Attach the Right Upright (54) to the Base (52) in the same
way.
Unplug the power cord. CAUTION: You must be able to
safely lift 20 kg (45 lbs.) to raise, lower, or move the
treadmill.
2
Latch
Pin
Latch
Knob
Catch
Bend
HOW TO MOVE THE TREADMILL
Frame
2. Slide the two Wheel Housings (62) onto the Base (52) with
the head of the Wheel Bolts (35) on the outside as shown.
Attach each Wheel Housing with two Wheel Housing Bolts
(6), two Wheel Housing Washers (11), and two Wheel
Housing Nuts (15).
2
Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the latch
pin is fully inserted into the catch.
35
62
6
15
11
35
52
15
62
11
6
1. Hold the handrails and place one foot against one of the
wheels. Do not pull back on the frame.
Handrail
2. Tilt the treadmill back until it rolls freely on the wheels, and
carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
3. Place one foot against one of the wheels, and carefully
lower the treadmill until it is in the storage position.
6
15
Wheel
HOW TO CHANGE THE INCLINE OF THE TREADMILL
To vary the intensity of your exercise, you can change
the incline of the treadmill. There are three incline levels. Before changing the incline, remove the key
and unplug the power cord. Next, fold the treadmill
to the storage position (see page 15).
To change the incline, first remove the incline pin from
one of the incline legs. Adjust the incline leg to the desired position, and then fully reinsert the incline pin.
Adjust the other incline leg in the same way. CAUTION:
Before using the treadmill, make sure that both incline legs are at the same height and that both incline pins are fully inserted into the incline legs.
After you have adjusted the incline legs, lower the
treadmill (see page 16).
Incline
Pin
3. With the help of a second person, raise the Uprights
(53, 54) so the Base (52) is flat on the floor as shown.
Next, position the front of the treadmill Frame (51) between
the Uprights.
3
See the inset drawing. Locate the wire inside of the lower
end of the Right Upright (54). Secure the wire to the Wire
Harness (98) using the included plastic tie. Then, pull the
upper end of the wire until the end of the Wire Harness is
extending from the indicated hole in the upper end of the
Right Upright.
53
54
111
Have a second person lift and hold the front end of the
Frame (51). Hold a Frame Spacer (111) between the Right
Upright (54) and the Frame. Attach the Right Upright and
the Frame Spacer to the Frame with a Frame Bolt (1), a
Frame Washer (14), and a Frame Star Washer (9).
Incline
Leg
Incline Pin
Hole
Large
Hole
98
14
Repeat this step on the left side of the treadmill.
9
52
51
1
Wire
Tie
54
98
4. Turn the Console Assembly (91) face-down. Be careful
not to scratch the face of the Console Assembly.
4
5
Identify the Right Handrail (55), which has a large hole in
one side.
12
Attach the Right Handrail (55) to the Console Assembly
(91) with two Console Screws (4), a Crossbar Screw (5),
and a Crossbar Star Washer (12).
Large Hole
4
91
14
7
55
5. Place the Left Handrail (56) on the Console Assembly
(91). Attach the end of the ground wire from the Console
Assembly to the indicated small hole in the Left Handrail
with the Silver Ground Screw (8).
5
5
5
12
Before using the handgrip pulse sensor, remove the sheets of
clear plastic from the
metal contacts. In addition, make sure that
your hands are clean.
56
4
Attach the Left Handrail (56) to the Console Assembly
(91) with two Console Screws (4), a Crossbar Screw (5),
and a Crossbar Star Washer (12). Be careful not to
pinch the ground wire.
Ground Wire
8
Small
Hole
6
Connector
91
Insert the end of the Wire Harness (98) into the hole in
the bottom of the Right Handrail (55) and out of the large
hole in the side. Next, Insert the end of the Wire Harness
through the two looped plastic ties.
Press the end of the Wire Harness (98) into the indicated
connector on the back of the Console Assembly (91).
The end of the Wire Harness should slide easily into
the connector and snap into place. If it does not, turn
the end of the Wire Harness and try again. IF THE CONNECTOR IS NOT INSERTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS
TURNED ON.
7. Insert the slack in the Wire Harness (98) down into the
Right Upright (54). Then, tighten the two plastic ties
around the Wire Harness, and cut off the ends of the plastic ties.
Metal
Contacts
3
To measure your heart rate, stand on the foot
rails and hold the metal contacts—avoid moving
your hands. When your pulse is detected, the
small heart symbol in the lower right display will
flash, one or two dashes will appear, and then
your heart rate will be shown. For the most accurate heart rate reading, continue to hold the
contacts for about 15 seconds.
91
6. Hold the Console Assembly (91) near the Right Upright
(54). Touch the Right Handrail to discharge any static.
Each program consists of 30 one-minute periods.
One speed setting is programmed for each period.
Note: The same speed setting may be programmed for two or more consecutive periods.
The profiles on the left side of the Program Select
button show how the speed of the walking belt will
change during the programs.
Measure your heart rate if desired.
6
When either button is pressed, the treadmill will
automatically adjust to the speed setting that is
programmed for the first period of the program.
Hold the handrails and begin walking.
When the first period ends, a series of tones will
sound. If a different speed setting is programmed
for the second period, the speed setting will flash
in one of the displays to alert you, and then the
speed of the walking belt will change. The program will continue until all 30 periods are completed. The walking belt will then slow to a stop.
When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
remove the key from the console. Keep the key in a
secure place. Then, switch the on/off switch to the
“off” position and unplug the power cord.
54
If the speed setting is too high or too low during
the program, you can manually override the setting
by pressing the Speed buttons. However, when
the next period begins, the speed of the walking belt will change if a different speed setting
is programmed for the next period.
98
Plastic
Ties
HOW TO USE A SPEED PROGRAM
55
98
1
7
54
98
Plastic
Ties
Insert the key into the console.
To stop the program, press the Stop button. The
time will begin to flash in one of the displays. To
restart the program, press the Start button or the
Speed increase button. The walking belt will begin
to move at 2 km/h. When the next period begins,
the speed of the walking belt will change if a different speed setting is programmed for the next period.
See HOW TO TURN ON THE POWER on page
11.
2
Select one of the four speed programs.
To select a speed program, press the
Program Select button
repeatedly; “P-1,” “P-2,”
“P-3,” or “P-4” will appear in the priority display for a few seconds to show which program is
selected. The maximum speed setting of the selected program will also appear in one of the displays for a few seconds.
4
Follow your progress with the track and the
three displays.
See step 4 on page 12.
5
When you are finished exercising, remove the
key.
See step 6 on this page.
3906ETW1
3906WETL1
8
Press the Start button or the Speed increase
button to start the program.
13
The lower left
display—As you exercise, the lower left display can show the
elapsed time and the
distance that you have
walked or run.
HOW TO USE THE MANUAL MODE
1
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
11.
2
The lower right
display—The lower right
display can show the
speed of the walking belt
and the approximate
number of calories that
you have burned. The display also shows your
heart rate when you use the handgrip pulse sensor (see step 5).
Select the manual mode.
When the key is inserted, the manual
mode will be selected.
If you have selected a
speed program, reselect the manual mode
by pressing the Program Select button repeatedly
until only zeros appear in the displays.
3
The priority display—
The upper display is the
priority display. The priETW13906
ority display can show
WETL13906
the elapsed time, the
distance that you have
walked or run, the speed of the walking belt, or the
approximate number of calories you have burned.
Press the Priority Display button repeatedly until
the priority display shows the information that you
are most interested
ETW13906 in viewing. Note: While information is shown WETL13906in the priority display, the same
information will not be shown in the lower left or
right display.
Press the Start button or the Speed increase
button to start the walking belt.
When either button is pressed, the walking belt will
begin to move at 2 km/h. Hold the handrails and
begin walking. As you exercise, change the speed
of the walking belt as desired by pressing the
Speed buttons. Each time a button is pressed, the
speed setting will change by 0.1 km/h; if a button
is held down, the speed setting will change in increments of 0.5 km/h. Note: After the buttons are
pressed, it may take a moment for the walking belt
to reach the selected speed setting.
8
91
Slot
54
7
Insert the slack in the Wire Harness (98) down into the
Right Upright (54).
Attach the Console Back (93) to the Console Assembly
(91) with four Console Back Screws (7). Make sure that
the Wire Harness (98) is in the indicated slot in the
Console Back and that no wires are pinched.
93
98
7
10
13
3
9. Carefully lower the Handrails (55, 56) to the floor. Center
the Frame (51) between the Handrails, and tighten the
four Upright Bolts (2). Then, raise the Handrails back to
the vertical position.
See the inset drawing. Attach the Latch Assembly (108) to
the Left Upright (53) with two Latch Screws (7). Make
sure that the Latch Assembly is oriented as shown.
9
2
51
55, 56
See HOW TO CHANGE THE INCLINE OF THE TREADMILL on page 14. Adjust the incline of the treadmill as desired.
53
To reset the displays, press the Stop button, remove the key, and then reinsert the key.
To stop the walking belt, press the Stop button.
The time will begin to flash in one of the displays.
To restart the walking belt, press the Start button or
the Speed increase button.
60931EWT
Note: The console can
display speed and dis- 6390WE1T
tance in either kilome- 6390TL1WE
ters or miles. To see
which unit of measurement is selected, hold
down the Stop button, insert the key into the con906E13TW
sole, and then release the Stop button. An “M” for
906L13WET
metric kilometers or an “E” for English miles will
appear in the priority display. Press the Speed increase button to change the unit of measurement.
When the desired unit of measurement is selected,
remove the key and then reinsert it.
60931LTEW
4
8. Set the Console Assembly (91) on the Right Upright (54)
and the Left Upright (not shown). Next, start four Handrail
Bolts (3) with four Handrail Washers (13) and four
Handrail Star Washers (10) (only two of each are shown)
into the Right Upright and the Left Upright. Then, tighten
all four Handrail Bolts.
Follow your progress with the track and the
three displays.
The track—The track
represents a distance of
400 meters (1/4 mile).
As you walk or run on
the treadmill, the indicators around the track
will appear in succession until the entire track appears. The track will then disappear and the indicators will again begin to appear in succession.
The center of the track will show the number of
laps that you have completed.
12
108
7
10.Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. Keep the included hex keys in a secure place; the large hex key is used to adjust the walking belt
(see page 18). To protect the floor or carpet, place a mat under the treadmill.
9
CONSOLE DIAGRAM
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear.
UK
HOW TO PLUG IN THE POWER CORD
This product must be earthed. If it should malfunction or break
down, earthing provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped
with a power cord having an equipment-earthing conductor and an
earthing plug. Important: If the power cord is damaged, it must
be replaced with a manufacturer-recommended power cord.
1
Socket on treadmill
UK
See drawing 1. Plug the indicated end of the power cord into the
socket on the treadmill.
See drawing 2. Press the pins on the power cord into the metal clips
in the adapter as shown. Close the adapter cover over the end of the
power cord and tighten the screw in the adapter. Important: Make
sure that the adapter cover is secure and the screw has been
tightened before using the power cord.
FR/SP
2
Key
Adapter
Cover
Screw
Clip
Pins
Adapter
See drawing 3. Plug the power cord into an appropriate outlet that is
properly installed and earthed in accordance with all local codes and
ordinances. Important: The treadmill is not compatible with
GFCI-equipped outlets.
3
FR/SP
Metal
Clips
Outlet
IT
UK
GR
DANGER:
Improper connection of the equipment-earthing conductor can result in an increased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as
to whether the product is properly earthed. Do not modify the plug provided with the product—if it will
not fit the outlet, have a proper outlet installed by a qualified electrician.
IT
FEATURES OF THE CONSOLE
HOW TO TURN ON THE POWER
The treadmill console offers a selection of features
designed to make your workouts more effective.
Plug in the power cord (see
page 10). Next, locate the
on/off switch on the treadmill
frame near the right upright.
Make sure that the switch is
in the “on” position.
While the manual mode of the console is selected, the
speed of the treadmill can be changed with the touch
of a button. As you exercise, the displays will provide
continuous exercise feedback. You can even measure
your heart rate using the built-in pulse sensor.
Next, stand on the foot rails of the treadmill. Find the
clip attached to the key (see the drawing above), and
slide the clip onto the waistband of your clothes. Then,
insert the key into the console. After a moment, the
track and the three displays will light. Important: In an
emergency situation, the key can be pulled from
the console, causing the walking belt to slow to a
stop. Test the clip by carefully taking a few steps
backward; if the key is not pulled from the console,
adjust the position of the clip.
The console also offers four speed programs. Each
program automatically controls the speed of the treadmill as it guides you through an effective workout.
Note: If there is a sheet of clear plastic on the console, peel off the plastic. To prevent damage to the
walking platform, always wear clean athletic shoes
while using the treadmill. During the first few minutes that the treadmill is used, inspect the alignment of the walking belt, and center the walking
belt if necessary (see page 18).
GR
FR/SP
3906E1TW
3906L1WET
10
On
Position
11
Handrail Washer (11)–2
Latch Screw
(8)–2
Console Back
Screw (58)–4
PART LIST—Model No. WETL13906.0
Key
No. Qty.
1
2
3
4
5
6
7
Description
Key
No. Qty.
Description
2
4
4
4
2
4
6
R0306A
Key
No. Qty.
Description
Frame Pivot Bolt
42
6
Electronics Star
82
1
Tie Holder
Upright Bolt
Washer
83
1
Reed Switch Clip
Handrail Bolt
4
Incline Leg Washer
43
1
Belly Pan Grommet
84
Console Screw
44
2
Motor Tension Nut
85
1
Grommet
Crossbar Screw
45
2
Frame Pivot Nut
86
0
(Not Used)
Formed Washer (31)–4
Wheel Housing Bolt
46
5
Nut
87
1
Star Washer (33)–2 Controller
Latch Screw/
47
Hood Clip
88
1
Transformer
3” Bolt5(30)–4
Console Back Screw
48
4
Handrail Nut
89
1
Filter
8
1
Silver Ground Screw
49
3
Small Nut
90
1
Power Cord
9
2
Frame Star Washer
50
2
Isolator Fastener
91
1
Console Assembly
10
4
Handrail Star Washer
51
1
Frame
92
1
Console Crossbar
Console Screw/
11
4
Wheel Housing
52
1
Base
93
1
Console
Latch Screw
Washer
53
1
Left Upright
94(70)–7
0
(Not Used)
12
2
Crossbar StarConsole
WasherBack54
1
Right Upright
95
1
Ground Wire
Screw (58)–455
13
4
Handrail Washer
1
Right Handrail
96
1
Ground Wire
14
2
Frame Washer
56
1
Left
97
1
Reed Switch
3/8”Handrail
Star Washer
15
4
Wheel Housing Nut
57
1
Electronics
Bracket 13mm98Screw1
Wire Harness
(69)–2
(20)–6
16
4
Upright Nut
58
1
Dust Guard
99
1
Outlet Plate Assembly
17
1
16 mm Hex Key
59
1
Motor Bracket
100
1
Walking Platform
18
1
4 mm Hex Key
60
1
Left Rear
101
1
Walking Belt
19
2
Roller Bracket Screw
Roller Bracket
102
0
(Not Used)
20
5
Hood Screw
61
1
Right Rear
103
2
Belt Guide
21
18
Screw
Roller
104
1
Front Roller/Pulley
3” Bolt
(2)–4Bracket
22
1
Front
Roller
Adj.
Bolt
62
2
Wheel
Housing
105
1
Magnet
Star Washer (9)–6
63
6
Base Pad
106
1
Motor Belt
(May be an 23
internal1 StarGround
Washer)Screw
24
2
Outlet Plate Bolt
64
1
Latch Catch
107
1
Rear Roller
25
10
Foot Rail Screw
65
1
Hood
108
1
Latch Assembly
26
6
Base Pad Screw
66
1
Belly Pan
109
1
Key/Clip
Wheel 67
Nut (38)–2
27
2
Walking Platform Bolt
1
Left Foot Rail
110
2
Incline Pin
28
4
Belt Guide Screw
68
1
Right Foot Rail
111
2
Frame Spacer
29
2
Rear Roller Adj. Bolt
69
2
Incline Leg
112
1
Power Adapter
30
2
Motor Bolt
70
2
Wheel
113
1
Warning Decal
31
1
Motor Pivot Bolt
71
4
Wheel Spacer
114
1
Tie Holder Screw
32
2
Incline Leg Bolt
72
1
Motor Isolator
#
1
6” Red Wire, M/F
33
2
Isolator Screw
73
2
Motor Bushing
#
1
4” Black Wire, M/F
2
Motor Tension Bolt
34
4
Frame Endcap
74
1
4” Blue Wire, M/F
#
U-nut
(105)–4
35
2
Wheel Bolt
75
2
Upright
Endcap
#
1
8” Blue Wire, 2F
36
2
Rear Roller
76
4
Handrail Endcap
#
1
10” Blue Wire, 2F
Star Washer
77
2
Platform
#
1
6” White Wire, 2F
Front Roller
1
37
Cushion, Front
10” White Wire, 2F
1
#
Star Washer
78
2
Platform
#
1
User’s Manual
383” Bolt
2 (30)–4
Motor Star Washer
Cushion, Center
2
Outlet Plate Washer
39
79
1
Drive Motor
#These parts are not illustrated
40
1
Ground Star Washer
80
4
Wire Tie
Specifications are subject to
41
13
Tek Screw
81
4
8” Tie
change without notice.
3/8” Washer (11)–6
5/16” Washer (31)–4
4” Bolt (120)–2
PART IDENTIFICATION
CHART
Remove this chart and use it to identify small parts during assembly. Save this chart and the EXPLODED
DRAWING/PART LIST for future reference.
Wheel Housing
Washer (11)–4
Crossbar Star
Washer (12)–2
Silver Ground
Screw (8)–1
Console
Screw (4)–4
Crossbar
Screw (5)–2
Latch/Console
Back Screw
(7)–6
Wheel Housing Bolt (6)–4
Handrail
Washer (13)–4
Handrail Star
Washer (10)–4
Upright Nut
(16)–4
Upright Bolt (2)–4
Frame Washer
(14)–2
Frame Star
Washer (9)–2
Wheel Housing
Nut (15)–4
Handrail Bolt (3)–4
Frame Pivot Bolt (1)–2
EXPLODED DRAWING—Model No. WETL13906.0
R0306A
7
21
30 34
38
73
7
44
38
72
34
23
40
79
97
25
83
33
25
77
103
67
105
76
7
3
4
12
76
13
114
10
5
3
57
25
95
104
76
37
4
108
21
47
54
1
25
41
113
21
14
80
65
25
9
77
50
100
21
42
111
47
47
101
2
103
60
36
9
47
28
19
29
51
32
43
43
41
81
66
39
110 69
11
39
15 15
29
17
18
61
46
43
32
49
41
20
36
35
26
110
71
70
21
41
41
20
84
63
63
62
51
26
2
98
63
26
63
26
6
71
58
46
69
16
11
99
43
74
1
52
6
24
46
14
82
24
20
20
111
21
90
112
20
79
27
21
42
107
46
3
5
33
41
74
3
10
13
76
47
45
68
27
13
12
7
75
10
55
21
22
25
98
76
48
21
21
41
82
53
64
19
75
41
10
13
56
89
28
41
48
21
42
33
79
93
85
21
42
88
31
45
106
50
25
96
49
21 46
7
109
59
25
91
8
92
87
63
11
11
15
51
71
70
15
16
62
35
71
63
26
26
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement