COMPACT COMPONENT SYSTEM SISTEMAS DE COMPONENTES COMPACTOS SYSTEME DE COMPOSANTS COMPACT FS-V5 REMOTE CONTROL RM-RXFSV5 DIMMER SLEEP DISPLAY FM MODE AHB PRO AUTO PRESET PROGRAM RANDOM BASS TREBLE POWER MD/AUX CD REPEAT CANCEL UP SET DOWN TAPE TUNER BAND CD VOLUME INSTRUCTIONS MANUAL DE INSTRUCCIONES MANUEL D’INSTRUCTIONS For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Model No. Serial No. LVT0214-001A [J] Downloaded From DvDPlayer-Manual.com JVC Manuals Warnings, Cautions and Others / Mises en garde, précautions et indications diverses (For U.S.A) CAUTION RISK OF ELECTRIC SHOCK CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: G-1From DvDPlayer-Manual.com JVC Manuals Downloaded – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. For Canada/pour le Canada For Canada/pour le Canada CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. PRECAUTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND. THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,” ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS. CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS NUMERIQUES DE CLASSE B PRESCRITES DANS LA NORME SUR LE MATERIEL BROUILLEUR: “APPAREILS NUMERIQUES”, NMB-003 EDICTEE PAR LE MINISTRE DES COMMUNICATIONS. 1. CLASS 1 LASER PRODUCT 2. DANGER: Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam. 3. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualitied service personnel. 1. PRODUIT LASER CLASSE 1 2. ATTENTION: Radiation laser invisible quand l’appareil est ouvert ou que le verrouillage est en panne ou désactivé. Eviter une exposition directe au rayon. 3. ATTENTION: Ne pas ouvrir le couvercle du dessus. Iln’y a aucune pièce utilisable à l’intérier. Laisser à un personnel qualifié le soin de réparer votre appareil. CAUTION ATTENTION To reduce the risk of electrical shocks, fire, etc.: 1. Do not remove screws, covers or cabinet. 2. Do not expose this appliance to rain or moisture. Afin d’èviter tout risque d’électrocution, d’lncendie. etc.: 1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l’appareil. 2. Ne pas exposer l’appareil à la pluie ni à l’humidité. Caution — POWER switch! Disconnect the mains plug to shut the power off completely. The POWER switch in any position does not disconnect the mains line. The power can be remote controlled. Downloaded From DvDPlayer-Manual.com JVC Manuals Attention — Commutateur POWER! Déconnecter la fiche de secteur poru couper complètement le courant. Le commutateur POWER ne coupe jamais complètement la ligne de secteur, quelle que soit sa position. Le courant peut être télécommandé. G-2 English Thank you for purchasing the JVC Compact Component System. We hope it will be a valued addition to your home, giving you years of enjoyment. Be sure to read this instruction manual carefully before operating your new stereo system. In it you will find all the information you need to set up and use the system. If you have a query that is not answered by the manual, please contact your dealer. Features Here are some of the things that make your System both powerful and simple to use. ■ The controls and operations have been redesigned to make them very easy to use, freeing you to just enjoy the music. • With JVC’s COMPU PLAY you can turn on the System and automatically start the Radio, Cassette deck or CD Player with a single touch. ■ The System incorporates Active Hyper Bass PRO circuitry to faithfully reproduce low frequency sounds. ■ A 45-station preset capability (30 FM and 15 AM) in addition to auto-seek and manual tuning. ■ Versatile CD options include repeat, random and program play. ■ Timer functions; Daily Timer and Sleep Timer. ■ Auto-reverse tape function. ■ You can connect various external units, such as an MD recorder. How This Manual Is Organized • Basic information that is the same for many different functions - e.g. setting the volume - is given in the section ‘Common Operations’, and not repeated under each function. • The names of buttons/controls and display messages are written in all capital letters: e.g. TUNER BAND, “NO DISC”. • System functions are written with an initial capital letter only: e.g. Normal Play. Use the table of contents to look up specific information you require. We’ve enjoyed making this manual for you, and hope it serves you in enjoying the many features built into your System. IMPORTANT CAUTIONS 1. Installation of the System ■ • • • Select a place which is level, dry and neither too hot nor too cold. (Between 5°C and 35°C or 41°F and 95°F.) Leave sufficient distance between the System and a TV. Do not use the System in a place subject to vibrations. 2. Power cord ■ • • • Do not handle the power cord with wet hands! Some power is always consumed as long as the power cord is connected to the wall outlet. When unplugging the System from the wall outlet, always pull the plug, not the power cord. 3. Malfunctions, etc. ■ • • There are no user serviceable parts inside. In case of system failure, unplug the power cord and consult your dealer. Do not insert any metallic object into the System. ■ ■ Table of Contents Features ............................................................................... 1 How This Manual Is Organized .......................................... 1 IMPORTANT CAUTIONS ................................................ 1 Using the Timers ................................................... 16 Getting Started .........................................................2 Troubleshooting .................................................... 19 Common Operations ................................................6 Specifications ........................................................ 20 Using the Tuner ........................................................8 Using the CD Player ...............................................10 Using the Cassette Deck (Listening to a Tape) ....12 Using the Cassette Deck (Recording) ..................13 Using External Equipments ...................................15 1 From DvDPlayer-Manual.com JVC Manuals Downloaded Care And Maintenance ......................................... 18 English ■ ■ Getting Started Accessories Make sure that you have all of the following items, which are supplied with the System. Power Cord (1) AM Loop Antenna (1) Remote Control (1) Batteries (2) FM Wire Antenna (1) If any of these items are missing, contact your dealer immediately. How To Put Batteries In the Remote Control Match the polarity (+ and –) on the batteries with the + and – markings in the battery compartment. R6P(SUM-3)/AA(15F) CAUTION: Handle batteries properly. To avoid battery leakage or explosion: • Remove batteries when the Remote Control will not be used for a long time. • When you need to replace the batteries, replace both batteries at the same time with new ones. • Don’t use an old battery with a new one. • Don’t use different types of batteries together. Using the Remote Control The Remote Control makes it easy to use many of the functions of the System from a distance of up to 7m (23 feet) away. You need to point the Remote Control at the remote sensor on the System’s front panel. Remote sensor Downloaded From DvDPlayer-Manual.com JVC Manuals 2 English CAUTION: Make all connections before plugging the System into an AC power outlet. Connecting the FM Antenna Using the Supplied Wire Antenna FM wire antenna (supplied) OPTICAL DIGITAL OUT Using the Coaxial Type Connector (Not Supplied) A 75-ohm antenna with coaxial type connector should be connected to the FM 75-ohm COAXIAL terminal. L R L R If reception is poor, connect the outdoor antenna. FM outdoor antenna (Not supplied) Coaxial cable Note: Before attaching a 75 ohm coaxial lead (the kind with a round wire going to an outdoor antenna), disconnect the supplied FM Wire Antenna. Connecting the AM Antenna AM loop antenna (Supplied) OPTICAL DIGITAL OUT L Attach the AM loop to its base by snapping the tabs on the loop into the slot in the base. R R L ANTENNA FM (75Ω) COAXIAL AM EXT AM LOOP CAUTION: To avoid noise, keep antennas away from the System, the connecting cord and the AC power cord. 3 From DvDPlayer-Manual.com JVC Manuals Downloaded Turn the loop until you have the best reception. English CAUTION: Make all connections before plugging the System into an AC power outlet. Connecting the Speakers For each speaker, connect one end of the speaker wire to the speaker terminals on the back of the System. 1. Open each of the terminals and insert the speaker wires firmly, then close the terminals. 2. Connect the red (+) and black (–) wires of the right side speaker to the red (+) and black (–) terminals marked R on the System. Connect the red (+) and black (–) wires of the left side speaker to the red (+) and black (–) terminals marked L on the System. Right speaker (rear side) Left speaker (rear side) Black L R SPEAKERS IMPEDANCE MIN 4Ω CAUTION: A TV may display irregular colors if located near the speakers. If this happens, set the speakers away from the TV. Connecting External Equipment Connect signal cords (not supplied) between the System’s LINE IN (AUX)/LINE OUT terminals and the output/input terminals of the external MD recorder, tape deck, etc. You can then listen to the external source through the System, or record the System’s CD player, cassette tape, or tuner to the external unit. Signal cord (not supplied) Pin-plug x 2 MD recorder or tape deck (not supplied) Pin-plug x 2 LINE OUT R L LINE IN (AUX) Signal cord (not supplied) Pin-plug x 2 Pin-plug x 2 Connecting an MD Recorder, etc (Digital Output) Unplug the cap and connect an optical digital cord (not supplied) between the System’s OPTICAL DIGITAL OUT terminal and the input terminal of the MD recorder, etc. You can record the digital output signal from the System’s CD Player to the MD recorder, etc. Cap MD recorder, etc. (not supplied) OPTICAL DIGITAL OUT Downloaded From DvDPlayer-Manual.com JVC Manuals Optical digital cord (not supplied) 4 English Connecting the AC Power Cord Firmly insert the supplied AC power cord into the AC inlet on the back of the Unit. AC IN Power cord CAUTIONS: • • ONLY USE THE JVC POWER CORD PROVIDED WITH THIS SYSTEM TO AVOID MALFUNCTION OR DAMAGE TO THE SYSTEM. BE SURE TO UNPLUG THE POWER CORD FROM THE OUTLET WHEN GOING OUT OR WHEN THE SYSTEM IS NOT IN USE FOR AN EXTENDED PERIOD OF TIME. Now you can plug the AC power cord into the wall outlet, and your System is at your command! COMPU PLAY JVC’s COMPU PLAY feature lets you control the most frequently used System functions with a single touch. With One Touch Operation you can play a CD, a tape, turn on the radio, or listen to an external equipment with a single press of the play button for that function. One Touch Operation turns the power on for you, then starts the function you have specified. If the System is not ready (no CD in place), the System still powers on so you can insert a CD. How One Touch Operation works in each case is explained in the section dealing with that function. The COMPU PLAY buttons are: On the Unit CD #¥8 button TUNER BAND button TAPE @ # button MD/AUX button On the Remote Control CD #8 button TUNER BAND button TAPE @ # button MD/AUX button AUTOMATIC POWER ON The System automatically turns on with the following operation. • When you press the CD 0 button, the System automatically turns on and the CD cover opens to allow CD insertion. However, this operation does not change the function to CD. When you press the POWER button to turn off the System, the CD cover will automatically closed if it is opened. 5 From DvDPlayer-Manual.com JVC Manuals Downloaded English ■ ■ Common Operations REMOTE CONTROL RM-RXFSV5 DIMMER SLEEP POWER DISPLAY FM MODE MD/AUX AHB PRO AUTO PRESET DIMMER DISPLAY AHB PRO POWER PROGRAM RANDOM BASS TREBLE BASS TREBLE AUTO REVERSE CD AUTO TAPE SELECTOR REPEAT ON/STANDBY indicator POWER CANCEL POWER MD/AUX DOWN UP REC SET DOWN TAPE VOLUME+,– ON/STANDBY TUNER BAND AHB PRO AHB PRO REV.MODE SLEEP VOLUME CLOCK TAPE BAND TUNER MULTI CONTROL CD OPEN/CLOSE CD UP CLOCK TIMER/ SNOOZE PHONES PHONES OPTICAL DIGITAL OUTPUT VOLUME+,– CD VOLUME Turning the Power On and Off Turning the System On —————— Adjusting the Volume Press the VOLUME + button to increase the volume or press the VOLUME – button to decrease it. Press the POWER button. The display comes on and “HELLO” is displayed once. The ON/ STANDBY indicator lights in green. The System comes on ready to continue in the mode it was in when the power was last turned off. ■ For example, if the last thing you were doing was listening to a CD, you are now ready to listen to a CD again. If you wish, you can change to another source. ■ If you were listening to the Tuner last, the Tuner comes on playing the station it was last set to. Turning the System Off —————— Press the POWER button again. “GOOD BYE” is displayed and the display goes out, except for the clock display. The ON/STANDBY indicator lights in red. ■ Some power is always consumed even though power is turned off (called Standby Mode). ■ To switch off the System completely, unplug the AC power cord from the wall outlet. When you unplug the AC power cord, the clock will be reset to AM 12:00 after about 20 minutes. You can adjust the volume level between 0 and 50. CAUTION: DO NOT turn on the System and/or start playing any source without first setting the VOLUME control to minimum, as a sudden blast of sound could damage your hearing, speakers and/ or headphones. For private listening Connect a pair of headphones to the PHONES jack. No sound comes out of the speakers. Be sure to turn down the volume before connecting or putting on headphones. Adjusting the Brightness (DIMMER) You can adjust the brightness of the backlighting for the display. When the System is Turned On —— To make the brightness of the backlighting darker, press the DIMMER button on the Remote Control. To make the brightness brighter, press the DIMMER button on the Remote Control again. When the System is Turned Off (STANDBY MODE) ————————— To turn on the backlighting, press the DIMMER button on the Remote Control. The brightness is the same as for darker one mentioned above. To turn off the backlighting, press the DIMMER button on the Remote Control again. Downloaded From DvDPlayer-Manual.com JVC Manuals 6 English Reinforcing the Bass Sound (AHB PRO) Showing the Time (DISPLAY) You can reinforce the bass sound to maintain rich, full bass at low volume (you can use this effect only for playback): To get the effect, press the AHB (Active Hyper Bass) PRO button. The “BASS” indicator lights up on the display. To cancel the effect, press the button again. The “BASS” indicator goes out. Tone Control (BASS/TREBLE) You can control the tone by changing the bass and treble. The analog clock acts to display the bass and treble settings. By pressing either the BASS or TREBLE button on the Remote Control, you can visually see the current tone control settings. In Standby mode, the digital clock and analog clock appear on the display at the same time. Meanwhile, only the analog clock is displayed when a music source is selected. Namely, you can see the analog clock at all times. When the System is turned on, you can display the digital clock at any time. To display the digital clock, press the CLOCK button on the Unit or DISPLAY button on the Remote Control. To return to the previous mode, press the same button again. Minute Hand Second Hand Hour Hand Examples: FLAT ( ) Fully boosted ( BASS Control ( ) ) ( ) ——————————— You can adjust the bass level (low frequency range level) between –6 and +6. (0: Flat) 1. Press the BASS button on the Remote Con■ trol. 2. Press the UP or DOWN button on the ■ Remote Control to adjust the bass level. BASS UP DOWN TREBLE Control —————————— You can adjust the treble level (high frequency range level) between –6 and +6. (0: Flat) 1. Press the TREBLE button on the Remote ■ Control. 2. Press the UP or DOWN button on the ■ Remote Control to adjust the treble level. TREBLE DOWN UP 7 From DvDPlayer-Manual.com JVC Manuals Downloaded Note: To let the clock work, you need to set the clock beforehand. (See “Setting the Clock” on page 16.) English ■ ■ Using the Tuner REMOTE CONTROL RM-RXFSV5 DIMMER SLEEP POWER DISPLAY FM MODE MD/AUX AHB PRO AUTO PRESET PROGRAM RANDOM BASS TREBLE FM MODE ON/STANDBY POWER MD/AUX CD AUTO PRESET DOWN TAPE BAND TUNER MULTI CONTROL CD OPEN/CLOSE CD TUNER BAND UP ¢ 4 REPEAT CANCEL PHONES OPTICAL DIGITAL OUTPUT SET UP > UP < SET Band display, Frequency display, Preset channel DOWN DOWN TAPE TUNER BAND CD TUNER BAND 4 ¢ FM mode indicators VOLUME When the System is in use, the display shows other items as well. For simplicity, we show here only the items described in this section. You can listen to FM and AM stations. Stations can be tuned in manually, automatically, or from preset memory storage. ■ Before listening to the radio: • Make sure that both the FM and AM antennas are correctly connected. (See page 3). One Touch Radio ————————— Just press the TUNER BAND button to turn on the System and start playing the station you were last tuned to. ■ You can switch from any other sound source to the radio by pressing the TUNER BAND button. The Band and Frequency you were last tuned to appear on the display. (If the last station was selected using the preset number, the preset number appears first.) Each time you press the button, the band alternates between FM and AM. FM AM UP DOWN or (After 1 second) You can preset up to 30 FM stations and up to 15 AM stations using the Remote Control. 1. Press the TUNER BAND button. ■ AM Preset Tuning using the Remote Control (Possible only after presetting stations) Select the desired preset number using the Up, Down, > and < button on the Remote Control. After 1 second the display will show the preset number’s band and frequency. Example: Press the UP button until the preset number 12 “P12” appears. Presetting Stations Tuning In a Station TUNER BAND ■ BAND TUNER Note: Preset numbers may have been set to factory test frequencies prior to shipment. This is not a malfunction. You can preset the stations you want into memory by following one of the presetting methods below. Manual Presetting FM SET TUNER BAND (on the Remote Control) methods. ■ SET STORED UP Manual Tuning Press the 4 or ¢ button on the Unit or the Remote Control repeatedly to move from frequency to frequency until you find the station you want. OR Auto Tuning If you press and hold the 4 or ¢ button on the Unit or the Remote Control for one second or more, the frequency changes down, or up, automatically until a station is found. OR Downloaded From DvDPlayer-Manual.com JVC Manuals DOWN SET or (on the Unit) 2. Select a station using one of the following ■ ■ ————————— (Within 5 seconds) When changing the Band FM = 30,AM = 15 1. Select a band by pressing the TUNER ■ BAND button. 2. Press the 4 or ¢ button to tune in a sta■ tion. 3. Press the SET button. ■ “SET” will blink for 5 seconds. Within 5 seconds, proceed to the next step. When the display returns to the one set in STEP 2 after 5 seconds, press the SET button again. 8 English 4. Press the UP, DOWN, >, or < button within 5 ■ seconds to select the preset number. UP or > button: Increases the preset number by 1. DOWN or < button: Decreases the preset number by 1. • When the > or < button is kept pressing, the preset number changes rapidly. 5. Press the SET button within 5 seconds. ■ “STORED” appears and after 2 seconds, the display returns to the broadcast frequency display. 6. Repeat above steps 1 to 5 for each station ■ you want to store in memory with a preset number. To change the preset stations, repeat the same steps as above. Auto Presetting In each band, you can automatically preset FM-30, AM-15 stations. Preset numbers will be allocated as stations are found, starting from the lowest frequency and moving up the frequency. AUTO PRESET TUNER BAND (for 2 seconds) 1. Select a band by pressing the TUNER ■ BAND button. 2. Press the AUTO PRESET button on the ■ Remote Control for more than two seconds. 3. Repeat steps 1-2 for the other band. ■ ■ If you want to change the preset stations, carry out the Manual Presetting for the desired preset numbers. CAUTION: Even if the system is unplugged or if the power failure occurs, the preset stations will be stored for about 24 hours. However, in case the preset stations are erased, you will need to preset the stations again. To Change the FM Reception Mode When you are tuned into an FM stereo broadcast, the “STEREO” indicator lights up and you can hear stereo effects. If an FM stereo broadcast is hard to receive or noisy, you can select Monaural mode. Reception improves, but you lose stereo effect. Press the FM MODE button on the Remote Control so that the “MONO” indicator lights up on the display. FM MODE STEREO MONO To restore the stereo effect, press the FM MODE button on the Remote Control so that the “MONO” indicator goes off. 9 From DvDPlayer-Manual.com JVC Manuals Downloaded English ■ ■ Using the CD Player REMOTE CONTROL RM-RXFSV5 PROGRAM DIMMER SLEEP POWER DISPLAY FM MODE MD/AUX AHB PRO AUTO PRESET PROGRAM RANDOM BASS TREBLE CD REPEAT CANCEL SET CD Cover CD 0 REPEAT RANDOM ON/STANDBY POWER MD/AUX TAPE DOWN PHONES < UP UP SET > BAND TUNER MULTI CONTROL CD OPEN/CLOSE CD UP CD OPEN/CLOSE 0 CD #¥8 ¢ 7 OPTICAL DIGITAL OUTPUT Track number, Playing time, Preset number 4 DOWN TAPE TUNER BAND CD 4 DOWN CD #8 Repeat indicator ¢ 7 Play mode indicator Music calendar VOLUME When the System is in use, the display shows other items as well. For simplicity, we show here only the items described in this section. You can use Normal, Random, Program or Repeat Play. Repeat Play can repeat all the tracks or just one of the tracks on the CD. Here are the basic things you need to know to play a CD and locate the different tracks on it. The Quickest Way To Start a CD Is With the One Touch Operation ■ • • Press the CD #¥8 button on the Unit or the Remote Control. The power is automatically turned on. If a CD is already inserted, it will start playing from the first track. If no CD is inserted, “NO DISC” appears on the display and the CD Player remains in Stop mode. • Track number exceeding 15 is not displayed. When you place or take out a CD, do not let it fall. Also, be careful not to scratch your fingers with a CD cover. To Unload a CD Take out the CD as shown below. To Insert a CD 1. Press the CD OPEN/CLOSE 0 button on the ■ Unit (or the CD 0 button on the Remote Control.) ■ To unload an 8 cm (3") CD, use the concavity to make removal easier. The CD cover opens. 2. Place a CD, with its label side out as ■ shown below. Press down on the CD’s center until you hear a click. Basics of Using the CD Player-Normal Play 3. Press the CD OPEN/CLOSE 0 button (or CD ■ 0 button) again to close the CD cover. • ■ ■ ■ To close the CD cover and play the CD, you can just press the CD #¥8 button. You can place an 8 cm (3'') CD without an adaptor. If the CD cannot be read correctly (because it is scratched, for example), “ 0 0:00” appears on the display. You can insert a CD while listening to the other source. CAUTIONS: • DO NOT try to open or close the CD cover by hands as it will be damaged. Downloaded From DvDPlayer-Manual.com JVC Manuals To Play a CD————————————— 1. Insert a CD. ■ 2. Press the CD #¥8 button. ■ The first track of the CD begins playing. Track number • • Playback time The track number that has already played disappears from the music calendar. The CD Player automatically stops when the last track of the CD has finished playing. 10 English To stop playing the CD, press the 7 button. The following information for the CD is displayed. Total track number Total playback time To stop playing and remove the CD, press the CD OPEN/ CLOSE 0 button on the Unit or CD 0 button on the Remote Control to open the CD cover. To pause, press the CD #¥8 button. The playback time blinks on the display. To cancel pause, press the same button again. Play continues from the point where it was paused. To Select a Track or Passage within a Track —————————————— During playback, press the 4 or ¢ (< or >) button to select the track you want. The selected track starts playing. • Press the ¢ or > button once to skip to the beginning of the next track. • Press the 4 or <button to skip to the beginning of the track being played. Press twice quickly to skip to the beginning of the previous track. • When the > or < button on the Remote Control is kept pressing, the track continuously skips. Search Play ———————————— Holding down the 4 or ¢ button, during playback, will fast forward/backwards the CD so you can quickly find a particular passage in the track you are listening to. Programming the Playing Order of the Tracks You can see the total playback time of programmed tracks on the display. Also, you can see the programmed tracks on the music calendar. 8. Press the CD #8 button. ■ The System plays the tracks in the order you have programmed them. ■ You can skip to a particular program track by pressing the 4 or ¢ button during Program Play. ■ To stop playing, press the 7 button once. To confirm the programmed tracks while the CD player is stopped, each time press the 4 or ¢ button; the tracks making up the program will successively be displayed in the programmed order. To delete all the tracks in the program, in stop mode, press the 7 button. Pressing the CD 0 button to open the CD cover will also clear the programmed tracks. To exit the program mode once, while the CD Player is stopped, press the PROGRAM button to light off the “CD PROGRAM” indicator. Notes: • If the total playback time of the programmed tracks exceeds 99 minutes 59 seconds, the total playback time will go out on the display. • If you try to program the 21th track, “MEMORY FULL” appears on the display for about 2 seconds. To Modify the Program ——————— Modify the contents of the program while the CD Player is stopped. Each time you press the CANCEL button, the last track in the program is deleted. To add new tracks to the end of the program, repeat above steps 5 to 7. Random Play You can program the playing order of the tracks using the Remote Control. ■ You can program up to 20 tracks in any desired order including the same tracks. ■ You can only make a program when the CD Player is stopped. The tracks will play in no special order when you use this mode. 1. Insert a CD. ■ 2. Press the CD #8 button. ■ 3. Press the 7 button to stop the CD. ■ 4. Press the PROGRAM button. ■ 2. Press the CD #8 button. ■ The System enters the programming mode and the “CD PROGRAM” indicator lights up. PROGRAM 5. Press the UP, DOWN, >, or < button to ■ select the track to program. UP or > button: Increases the track number by 1. DOWN or < button: Decreases the track number by 1. • When the > or < button is kept pressing, the track number changes rapidly. 6. Press the SET button. ■ Program order number UP SET (After 2 seconds) DOWN Total playback time of the programmed tracks 7. Repeat steps 5 and 6 to select the other ■ tracks for the program. 11From DvDPlayer-Manual.com JVC Manuals Downloaded 1. Press the RANDOM button on the Remote ■ Control. The “CD RANDOM” indicator lights up on the display. The tracks are played in random order. To skip a track during playback, press the ¢ button to jump to the next track in the random sequence. Press the 4 button to jump back to the start of a track being played. To exit Random Play mode, while the CD Player is stopped, press the RANDOM button to light off the “CD RANDOM” indicator and carry out Normal Play, or press the CD 0 button to open the CD cover. Repeating Tracks You can set the program or individual track playing to repeat as many times as you like. Press the REPEAT button on the Remote Control. The Repeat indicator changes with each press of the button, as shown below. = ALL =blank display = (back to the beginning) : Repeats one track. ALL : In Normal Play mode, repeats all the tracks. In Program Play mode, repeats all the tracks in the program. In Random Play mode, repeats all the tracks in random order. To exit Repeat mode, press the REPEAT button until the Repeat indicator on the display goes out. ■ In Random Play, as a matter of course, cannot be selected. ■ Repeat mode remains in effect even when you change the play mode. English the Cassette Deck ■ ■ Using ■ ■ (Listening to a Tape) Cassette holder AUTO REVERSE AUTO TAPE SELECTOR REMOTE CONTROL RM-RXFSV5 DIMMER SLEEP POWER ) (EJECT) ON/STANDBY POWER DISPLAY FM MODE MD/AUX MD/AUX DOWN AHB PRO AUTO PRESET BASS TREBLE BAND TUNER MULTI CONTROL CD OPEN/CLOSE TAPE @ # CD UP ¢ 7 4 CD PHONES PROGRAM RANDOM TAPE REPEAT OPTICAL DIGITAL OUTPUT CANCEL REC REV. MODE REV.MODE AHB PRO VOLUME SLEEP CLOCK TIMER/ SNOOZE VOLUME+,– UP SET Tape Direction indicator DOWN TAPE @ # TAPE TUNER BAND CD ¢ 7 4 Reverse Mode indicator VOLUME When the System is in use, the display shows other items as well. For simplicity, we show here only the items described in this section. The Cassette Deck allows you to play and record audio tapes. ■ With Automatic Tape Detection, you can listen to type I, II or IV tapes without having to change any settings. The use of tapes longer than 120 minutes is not recommended, since characteristic deterioration may occur and these tapes easily jam in the pinch-rollers and the capstans. One Touch Play —————————— By pressing the TAPE @ # button on the Unit or the Remote Control, the Unit will come on, “TAPE” appears in the display, and if a tape is in the deck, it will start to play. If no tape is loaded, “NO TAPE” appears on the display, the Unit will come on and wait for you to insert a tape, or select another function. Regular Play When the power is already on, you can use this basic procedure: 1. Press the ) (EJECT) button. ■ 2. When the cassette holder opens, put the ■ cassette in, with the side you want to listen facing up. • If the cassette holder does not open, turn the Unit off, then back on and press the ) (EJECT) button again. 5. If you need to change the playback direc■ tion, press the TAPE @ # again. The opposite side Tape Direction indicator lights up and the tape playback direction changes. To stop playing, press the ebutton. To remove the tape, stop the tape, and press the ) (EJECT) button. To Fast-Wind A Tape ———————— ■ Press the ¢ or 4 button on the Unit or the Remote Control to fast-wind the tape. ¡ or 1 indicator of the tape fast-wind direction appears on the display. • The Cassette Deck automatically stops when the tape reaches its end. Reverse Mode You can set a tape to play just one side, both sides in succession, or both sides continuously. Press the REV. MODE button on the Unit. The indicator changes with each press of the button as shown. = = = (back to the beginning) : The Cassette Deck automatically stops after playing one side of the tape. : The Cassette Deck automatically stops after playing both sides of the tape. (Stops when playback in the 2 direction is finished.) : The Cassette Deck continues to play both sides of the tape until the e button is pressed. 3. Close the holder gently until it clicks. ■ 4. Press the TAPE @ # button. ■ The tape is played in the direction shown by the Tape Direction indicator. Downloaded From DvDPlayer-Manual.com JVC Manuals 12 English the Cassette Deck ■ ■ Using ■ ■ (Recording) AUTO TAPE SELECTOR REMOTE CONTROL RM-RXFSV5 DIMMER SLEEP POWER DISPLAY FM MODE MD/AUX AHB PRO AUTO PRESET REC AUTO PRESET PROGRAM RANDOM BASS TREBLE REC AHB PRO REV.MODE SLEEP VOLUME CLOCK TIMER/ SNOOZE REV. MODE CD REPEAT CANCEL Tape Direction indicator UP SET DOWN TAPE @ # TAPE TUNER BAND CD TAPE REC indicator Reverse Mode indicator 7 When the System is in use, the display shows other items as well. For simplicity, we show here only the items described in this section. VOLUME Recording onto a tape from any of the sound sources is simple. Just place a tape in the Cassette Deck, have the source ready, make one or two settings, and you’re ready to record. For each source the procedure is a little bit different so we explain each separately. But first, here are a few things to make your recordings better. Things To Know Before You Start Recording ————————————— ■ It should be noted that it may be unlawful to re-record ■ ■ ■ pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or artistic work embodied therein. When you want to record onto both sides of a tape, you can set Reverse mode to do so. Recording automatically stops after recording in the 2 direction. Therefore, make sure that the tape direction is 3 when recording with Reverse mode on. The recording level, which is the volume at which the new tape is being made, is automatically set correctly, so it is not affected by the VOLUME control on the System. Nor is it affected by adjusting the sound effects. Thus, during recording you can adjust the sound you are actually listening to without affecting the recording level. Two small tabs on the back of the cassette tape, one for side A and one for side B, can be removed to prevent accidental erasure or recording. Type II detection slot Adhesive tape ■ ■ CAUTION: If a recording you make has excessive noise or static, the Unit may have been too close to a TV which was on during the recording. Either turn off the TV or increase the distance between the TV and the System. Standard Recording You can record any sound source to tape as follows: 1. Insert a blank or erasable tape into the ■ Cassette Deck and wind past the tape leader. 2. Press the REV. MODE button on the Unit if ■ you want to record on both sides of the tape. Press the button until the indicator is lit. • When using Reverse mode, insert the tape so that it will be recorded in the forwards 3 direction. 3. Check the recording direction for the ■ tape. Make sure that the Tape Direction indicator is the same as that for the tape in the Cassette Deck. If the directions are different, press the TAPE @ # button to correct the tape direction and then press the e button to stop the tape. 4. Prepare the source, by, for example, tuning ■ in a radio station or turning on connected auxiliary equipment. Note: For CD recording, refer to “CD Direct Recording” mentioned below. To record on a cassette with the tabs removed, you must cover the holes with adhesive tape first. However, when a type II tape is used, only cover part of the hole as shown, since the other part of the hole (Type II detection slot) is used to detect the tape type. Type I and Type II tapes can be used for recording. Note: At the start and end of cassette tapes, there is leader tape which cannot be recorded onto. Thus, when recording CDs or radio broadcasts, wind on the leader tape first to ensure getting the beginning of the recording. 13From DvDPlayer-Manual.com JVC Manuals Downloaded 5. Press the REC button on the Unit. ■ The “TAPE REC” indicator lights up and the System begins recording. • If the tab of the cassette tape is removed to prevent erasure or recording, “NO REC” will appear on the display. • When recording in Reverse mode, the System automatically stops when it reaches the end of the reverse 2 direction. To record on both sides of a tape, make sure that the recording direction for the tape inserted is forwards 3, and that the Tape Direction indicator is also forwards 3, before you start recording. To Stop at Any Time During the Recording Process • If you make a recording with Reverse mode on, the Unit will record the last song at the end of the first side onto the next side from its beginning when the song has been recorded more than 12 seconds on the first side. If the last song has been recorded less than 12 seconds, then the previous song will again be recorded on the next side as it will not be completely recorded on the first side because of leader tape. After the CD player has played the entire CD, or all the programmed tracks, the tape automatically stops. Press the e button. Recording an AM station to tape When recording an AM broadcast, beats may be produced which are not heard when listening to the broadcast. If this happens, press the AUTO PRESET button on the Remote Control to eliminate the beats. 1. Set to AM station and start recording. 2. Press the AUTO PRESET button to eliminate the beats. Each time you press the button, the display changes as shown below: CUT-1= CUT-2 = CUT-3 = (back to the beginning) To stop at any time during the recording process, press the e button. The tape stops after four seconds. Note: When making SLEEP timer settings while doing CD Direct recording, set enough time to allow for the CD to finish playing, otherwise the power will go off before recording is completed. One Track Recording ———————— 1. Insert a cassette into the Cassette Deck ■ and wind past the tape leader. CD Direct Recording Everything on the CD goes onto the tape in the order it is on the CD, or according to the order you have set in a program. 1. Insert a cassette into the Cassette Deck ■ and wind past the tape leader. 2. Play the track on the CD you wish to ■ record. 3. Press the REC button on the Unit. ■ The CD player returns to the beginning of that track and the track is recorded on the tape. After recording, the CD player and Cassette Deck automatically stop. 2. Insert a CD. ■ 3. Press the CD #¥8 button on the Unit or on ■ the Remote Control. 4. Press the e button. ■ • If you want to record specific tracks only, program the tracks beforehand. You can check their total playback time on the display during programming. (See page 11.) 5. If you want to record on both sides of a ■ tape, press the REV. MODE button on the Unit until the “ ” indicator is lit. Make sure that the recording direction for the tape and the Tape Direction indicator is correct. (See “Notes for using Reverse mode for recording”.) 6. Choose whether to have pauses between ■ recorded selections. • If nothing is done, a non-recorded pause of about four seconds will be automatically left between selections. • If you do not want pauses between selections, do the following before proceeding to the next step. Press the CD #¥8 button on the Unit or the Remote Control twice. The CD player enters Pause mode. 7. Press the REC button on the Unit. ■ The “TAPE REC” indicator lights up and the System begins recording. Downloaded From DvDPlayer-Manual.com JVC Manuals 14 English Notes for using Reverse mode for recording English ■ ■ Using External Equipments REMOTE CONTROL RM-RXFSV5 DIMMER SLEEP POWER DISPLAY FM MODE MD/AUX AHB PRO AUTO PRESET PROGRAM RANDOM MD/AUX CD REPEAT ON/STANDBY POWER BASS TREBLE CANCEL MD/AUX DOWN TAPE BAND TUNER MULTI CONTROL CD MD/AUX OPEN/CLOSE CD UP UP PHONES SET OPTICAL DIGITAL OUTPUT DOWN TAPE TUNER BAND CD VOLUME Listening to External Equipment You can listen to external equipment such as MD recorder, turntable or other auxiliary. ■ First make sure that the external equipment is properly connected to the System. (See page 4). 1. Set the VOLUME control to the minimum ■ position. 2. Press the MD/AUX button. ■ “AUX” appears on the display. 3. Start playing the external equipment. ■ 4. Adjust the VOLUME control to the desired ■ listening level. 5. Apply sound effects, if you wish. ■ ■ ■ Press the AHB PRO button to reinforce the bass sound. Press the BASS/TREBLE button on the Remote Control to control the tone. (See “Tone Control” on page 7.) To exit MD/AUX mode, you will automatically switch out of MD/AUX mode when you select another source. Note: For operation of the external equipment, refer to its Instructions. 15From DvDPlayer-Manual.com JVC Manuals Downloaded Recording the System’s source to External Equipment You can record the System’s source to external equipment which is connected to the LINE OUT or OPTICAL DIGITAL OUT terminals of the System, such as cassette deck or MD recorder, etc. ■ First make sure that the external equipment is properly connected to the System. (See page 4). 1. Play the System’s CD Player, Cassette ■ Deck, or tune into a station. ■ The recording level is not affected by the VOLUME level set by the System. Also it is not affected by the sound effects. Note: For operation of the external equipment, refer to its Instructions. English ■ ■ Using the Timers AUTO TAPE SELECTOR REMOTE CONTROL RM-RXFSV5 DIMMER SLEEP ON/STANDBY POWER POWER MD/AUX SLEEP DISPLAY FM MODE AHB PRO AUTO PRESET PROGRAM RANDOM BASS TREBLE DOWN TAPE BAND TUNER MULTI CONTROL CD OPEN/CLOSE CD UP ¢ 4 MD/AUX REC CD SLEEP AHB PRO REV.MODE VOLUME SLEEP CLOCK CLOCK TIMER/ SNOOZE TIMER/ SNOOZE REPEAT PHONES OPTICAL DIGITAL OUTPUT CANCEL ON time, OFF time UP SET DOWN Timer indicator TAPE TUNER BAND CD REC indicator SLEEP indicator SNOOZE indicator When the System is in use, the display shows other items as well. For simplicity, we show here only the items described in this section. VOLUME The timers let you control listening and recording functions automatically. 1. Press the POWER button to turn on the Sys■ tem. 2. Setting the ON time (Example: PM 12:15). ■ Setting the Clock • When you plug the AC power cord into the wall outlet, the time indication blinks on the display. You can set the clock whether the System is on or off. In addition to the digital clock, the analog clock also shows the time. • Notes: • The clock must be correctly set for the timers to work. • The procedure must be completed within two minutes. Otherwise, the setting is cleared and must be repeated from the beginning. CLOCK DOWN MULTI CONTROL UP 1. Press the TIMER/SNOOZE button on the Unit. The Timer indicator lights up and the current ON time blinks on the display. When the clock is not set, the “CLOCK” indicator and the “ADJUST” indicator appear alternately on the display. Set the clock at first. 2. Press the ¢ or 4 button on the Unit to set the time you want the Unit to come on. Pressing the ¢ button moves the time forwards and pressing the 4 button moves it backwards. Hold down the button to move the time rapidly. CLOCK (for 2 seconds) 1. Press the CLOCK button on the Unit for ■ more than two seconds. The time indication rapidly blinks on the display. 3. Setting the OFF time (Example: PM 1:15). ■ 1. Press the TIMER/SNOOZE button on the Unit. The current OFF time blinks on the display. 2. Press the ¢ or 4 button on the Unit to set ■ the time. Pressing the ¢ button moves the time forwards and pressing the 4 button moves it backwards. Hold down the button to move the time rapidly. 2. Press the ¢ or 4 button on the Unit to set the time you want the Unit to be turned off. Pressing the ¢ button moves the time forwards and pressing the 4 button moves it backwards. Hold down the button to move the time rapidly. 3. Press the CLOCK button. ■ The selected time is set and the seconds start counting from 0. CAUTION: If there is a power failure, the clock loses its setting after about 20 minutes. “AM 12:00” blinks on the display and the clock must be reset. Note: The clock may gain or lose one to two minutes per month. 4. Selecting the music source. ■ Setting the Daily Timer Once you have set the Daily Timer, the timer will be activated at the same time every day. It can be cancelled and re-activate whenever you wish. The Timer indicator on the display shows when the Daily Timer you have set is in effect. Note: Perform each setting within 30 seconds. Otherwise, setting is cleared and the procedure must be repeated from the beginning. Downloaded From DvDPlayer-Manual.com JVC Manuals • 1. Press the TIMER/SNOOZE button on the Unit. The “TUNER” blinks on the display. 2. Press the ¢ or 4 button to select the music source you want to listen to. The display changes as shown below. TUNERÔTUNER RECÔCDÔTAPEÔ(back to the beginning) When you select the “TUNER REC”, the “REC” indicator appears on the display. 16 English 5. Setting the volume level. ■ 1. Press the TIMER/SNOOZE button on the Unit. The current volume setting blinks on the display. 2. Press the ¢ or 4 button to select the volume level. -: The current volume level will be used. 0 to 50: When the timer is turned on, the Volume will be automatically set to the selected level. Setting the SLEEP Timer Use the Sleep Timer to turn the System off after a certain number of minutes when it is playing. By setting the Sleep Timer, you can fall asleep to music and know that your System will turn off by itself rather than play all night. ■ You can only set the Sleep Timer when the System is on and a source is playing. 1. Play a CD, a cassette tape, or tune in to the ■ desired station. 6. Press the TIMER/SNOOZE button on the ■ Unit. The timer setting is completed and the display returns to the display before you set the timer. The timer indicator remains lit. 7. Before turning off the System, prepare the ■ music source selected in step 4. TUNER: Tune in to the desired station. TUNER REC: Tune in to the desired station and insert a cassette tape for recording the station. CD: Insert a CD. TAPE: Insert a tape. 8. Press the POWER button to turn off the ■ System. To cancel the timer, press the TIMER/SNOOZE button. The Timer indicator goes out on the display. To re-activate the cancelled timer, press the TIMER/ SNOOZE button to light the Timer indicator. Then, press the TIMER/SNOOZE button until the display returns to the original display. The Timer indicator should remain lit. To confirm the timer settings, cancel the timer once by pressing the TIMER/SNOOZE button. Then, press the TIMER/ SNOOZE button repeatedly, to see the current timer settings (ON time, OFF time, source, and volume). To change the timer setting, repeat the setting procedure from the beginning. • When the timer turns on, the Timer indicator starts blinking. CAUTION: If the System is unplugged, or a power failure occurs, the timer setting will be lost. You will need to reset the clock first, then the timer. 5-Minute Snoozing ————————— When the timer turns on the music source you can, if you wish, activate the 5-minute snoozing function to temporarily stop playback. Press the TIMER/SNOOZE button on the Unit. The “SNOOZE” indicator lights up on the display and the power is turned off for five minutes for snoozing. 17From DvDPlayer-Manual.com JVC Manuals Downloaded 2. Press the SLEEP button. ■ ■ The “SLEEP” indicator lights up. When the clock is not set, the “CLOCK” indicator and the “ADJUST” indicator appear alternately on the display. Set the clock at first. 3. Set the length of time you want the source ■ to play before shutting off. • Each time you press the SLEEP button, it changes the number of minutes shown on the display in this sequence: 10 = 20 = 30 = 60 = 90 = 120 = Cancelled = (back to the beginning) After setting the number of minutes for the Sleep Timer, the display will stop blinking and return to the display as before setting the Sleep Timer. (The display is dimmed.) The System is now set to turn off after the number of minutes you set. To Confirm the Sleep Time When the SLEEP button is pressed, the remaining sleep time is displayed. Wait until the display returns to the original display. To Cancel the SLEEP Timer Setting Press the SLEEP button until the “SLEEP” indicator goes out on the display. Turning off the System also cancels the SLEEP Timer. ■ If you are setting the Daily Timer, the System will be turned on at the set time to wake you up. Handle your CDs carefully, and they will last a long time. • Compact Discs • Only CDs bearing this mark can be used with this System. However, continued use of irregular shape CDs (heart-shape, octagonal, etc.) can damage the System. • Remove the CD from its case by holding it at the edges while pressing the case’s center hole lightly. Do not touch the shiny surface of the CD, or bend the CD. English ■ ■ Care And Maintenance If there are fingerprints, etc. on the lens, gently wipe clean with a cotton swab. Moisture Condensation • • • • Put the CD back in its case after use to prevent warping. Be careful not to scratch the surface of the CD when placing it back in the case. Avoid exposure to direct sunlight, temperature extremes, and moisture. Moisture may condense on the lens inside the System in the following cases: • After turning on heating in the room. • In a damp room. • If the System is brought directly from a cold to a warm place. Should this occur, the System may malfunction. In this case, leave the System turned on for a few hours until the moisture evaporates, unplug the AC power cord, and then plug it in again. Cassette Tapes A dirty CD may not play correctly. If a CD does become dirty, wipe it with a soft cloth in a straight line from center to edge. • If the tape is loose, it may get stretched, cut, or caught in the cassette. Take up the slack by inserting a pencil in one of the reels and rotating. CAUTION: Do not use any solvent (for example, conventional record cleaner, spray thinner, benzine, etc.) to clean a CD. • Do not touch the tape surface. General Notes • Do not store the tape: - In dusty places - In direct sunlight or heat - In moist areas - On a TV or speaker - Near a magnet • In general, you will have the best performance by keeping your CDs and the mechanism clean. • Store CDs in their cases, and keep them in cabinets or on shelves. • Keep the system’s CD cover closed when not in use. Cleaning the lens Cassette Deck If the lens in the CD pickup is dirty, dropout, etc., could degrade sound. Open the CD cover and clean the lens as shown. • Use a blower (available from a camera store) to blow dust off the lens. • • Blower If the heads, capstans, or pinch-rollers of the Cassette Deck become dirty, the following may occur: - Loss of sound quality - Discontinuous sound - Fading - Incomplete erasure - Difficulty recording Clean the heads, capstans, and pinch-rollers using a cotton swab moistened with alcohol. Capstans Pinch-rollers Erase head Lens Record/play head • • Downloaded From DvDPlayer-Manual.com JVC Manuals If the heads become magnetized, the Unit will produce noise or lose high frequency notes. To demagnetize the heads, turn off the Unit, and use a head demagnetizer (available at electronics and record shops). 18 English ■ ■ Troubleshooting • • If you are having a problem with your System, check this list for a possible solution before calling for service. If you cannot solve the problem from the hints given here, or the System has been physically damaged, call a qualified person, such as your dealer, for service. Symptom No sound is heard. Possible Cause Action • Connections are incorrect, or loose. • • Headphones are connected. • Check all connections and make corrections. (See pages 4- 5.) Disconnect the headphones. Unable to record. Cassette record protect tabs are removed. Cover the holes on the back edge of the cassette with tape. Poor radio reception • • • • • The antenna is disconnected. The AM Loop Antenna is too close to the System. The FM Wire Antenna is not properly extended and positioned. • Reconnect the antenna securely. Change the position and direction of the AM Loop Antenna. Extend FM Wire Antenna to the best reception position. The CD skips. The CD is dirty or scratched. Clean or replace the CD. The CD does not play. The CD is upside down. Put the CD in with the label side up. Unable to operate the Remote Control. • • Remove the obstruction. • Replace the batteries. • The path between the Remote Control and the sensor on the Unit is blocked. The batteries have lost their charge. Operations are disabled. The built-in microprocessor has malfunctioned due to external electrical interference. Unplug the System then plug it back in. The cassette holder cannot be opened. During tape playing, the power cord was unplugged. Plug in the power cord, press the POWER button, and then press the 0 button. 19From DvDPlayer-Manual.com JVC Manuals Downloaded English ■ ■ Specifications Amplifier Output Power 16 watts per channel, min. RMS, at 4 ohms from 80 Hz to 15 kHz, with no more than 10% total harmonic distortion (for U.S.A.) 34 W (17 W + 17 W) at 4 ohms (Max.) (for Canada) Input Sensitivity/Impedance (1 kHz) LINE IN (AUX) Output Sensitivity/Impedance (1 kHz) LINE OUT Optical out Speaker terminals Phones 500 mV/65 kohms 500 mV/4.3 kohms –21 dBm - –15 dBm 4 - 16 ohms 16 ohms - 1 kohm 0 - 15 mW/ch output into 32 ohms Cassette Deck Frequency Response TypeII (CrO2) 50 Hz - 15 kHz Wow and Flutter 0.15 % (WRMS) CD Player Signal-To-Noise Ratio 90 dB Wow And Flutter Unmeasurable Tuner FM Tuner Tuning Range 87.5 - 108.0 MHz AM Tuner Tuning Range 530 - 1,710 kHz Speaker Specifications (each unit) Speakers 8 cm cone Impedance 4 ohms Dimensions 140 ✕ 230 ✕ 217 mm (W/H/D) (5 - 9/16" ✕ 9 - 1/16" ✕ 8 - 9/16") Mass Approx. 1.8 kg (4.0 lbs) General Dimensions 438 ✕ 232 ✕ 310.5 mm (W/H/D) (17 - 1/4" ✕ 9 - 3/16" ✕ 12 - 1/4") Mass Approx. 7.2 kg (15.9 lbs) Accessories Power Cord (1) AM Loop Antenna (1) Remote Control (1) Batteries R6P (SUM-3)/AA (15F) (2) FM Wire Antenna (1) Power Specifications Power Requirements AC 120 V ~ , 60 Hz Power Consumption 37 watts (power on mode) 3 watts (in Standby mode) Design and specifications are subject to change without notice. Downloaded From DvDPlayer-Manual.com JVC Manuals 20 VICTOR COMPANY OF JAPAN, LIMITED EN, SP, FR Downloaded From DvDPlayer-Manual.com JVC Manuals 0499MNMCREJSC
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021