advertisement
Clear Spot 4G+ Personal Hotspot
User Guide
2131352
Rev 1.0
Important
Notice
Safety and
Hazards
Limitation of
Liability
Preface
Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or receive such data.
Do not operate the Sierra Wireless modem in areas where blasting is in progress, where explosive atmospheres may be present, near medical equipment, near life support equipment, or any equipment which may be susceptible to any form of radio interference. In such areas, the Sierra Wireless modem MUST BE
POWERED OFF . The Sierra Wireless modem can transmit signals that could interfere with this equipment.
Do not operate the Sierra Wireless modem in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, the Sierra Wireless modem MUST BE
POWERED OFF . When operating, the Sierra Wireless modem can transmit signals that could interfere with various onboard systems.
Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. Sierra Wireless modems may be used at this time.
The driver or operator of any vehicle should not operate the Sierra Wireless modem while in control of a vehicle. Doing so will detract from the driver or operator's control and operation of that vehicle. In some states and provinces, operating such communications devices while in control of a vehicle is an offence.
The information in this manual is subject to change without notice and does not represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND
ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL
DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL,
PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO,
LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE
ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS
PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE
FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY.
Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its affiliates aggregate liability arising under or in connection with the Sierra Wireless product, regardless of the number of events, occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the Sierra Wireless product.
Rev 1.0 Apr.10
3
Clear Spot 4G+ User Guide
Patents
Licenses
4
Portions of this product may be covered by some or all of the following US patents:
5,515,013
6,169,884
6,561,851
6,876,697
7,106,569
D599,256
5,629,960
6,191,741
6,643,501
6,879,585
7,145,267
D560,911
5,845,216
6,199,168
6,653,979
6,886,049
7,200,512
5,847,553
6,339,405
6,697,030
6,968,171
7,295,171
5,878,234
6,359,591
6,785,830
6,985,757
5,890,057
6,400,336
6,845,249
7,023,878
7, 287,162 D442,170
5,929,815
6,516,204
6,847,830
7,053,843
D459,303 and other patents pending.
This product includes technology licensed from QUALCOMM
®
3G
Manufactured or sold by Sierra Wireless or its licensees under one or more patents licensed from InterDigital Group.
A large amount of the source code to this product is available under licenses which are both free and open source. Most is available under the GNU General
Public License.
The remainder of the open source software which is not under the GPL is available under one of a variety of more permissive licenses. Those that require reproduction of the license text in the distribution are listed in the sections that follow (starting on
GNU General Public License
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc. 51 Franklin St, Fifth
Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the
Free Software Foundation's software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our
General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.
2131352
Rev 1.0 Apr.10
Preface
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND
MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this
General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered by this
License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices
5
Clear Spot 4G+ User Guide
6 stating that you changed the files and the date of any change. b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License. c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the
Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the
Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this
License.
3. You may copy and distribute the Program (or a work based on it, under Section
2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
2131352
Rev 1.0 Apr.10
Preface
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it.
However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this
License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you
(whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this
License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/ donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
7
Clear Spot 4G+ User Guide
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the
General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this.
Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS
NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE
COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM
“AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM
IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME
THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO
IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED
ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF
THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT
LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE
PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH
HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
END OF TERMS AND CONDITIONS
8 2131352
Rev 1.0 Apr.10
Preface
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found.
<one line to give the program's name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General
Public License as published by the Free Software
Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A
PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General
Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin St,
Fifth Floor, Boston, MA 02110-1301 USA
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type 'show w'.
This is free software, and you are welcome to redistribute it under certain conditions; type 'show c' for details.
The hypothetical commands ‘show w’ and ‘show c’ should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than ‘show w’ and ‘show c’; they could even be mouseclicks or menu items--whatever suits your program.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the program, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program ‘Gnomovision’ (which makes passes at compilers) written by James Hacker.
9
Clear Spot 4G+ User Guide
10
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Library General Public License instead of this
License.
iPerf License
Copyright (c) 1999-2007, The Board of Trustees of the University of Illinois
All Rights Reserved.
Iperf performance test
Mark Gates
Ajay Tirumala
Jim Ferguson
Jon Dugan
Feng Qin
Kevin Gibbs
John Estabrook
National Laboratory for Applied Network Research
National Center for Supercomputing Applications
University of Illinois at Urbana-Champaign http://www.ncsa.uiuc.edu
Permission is hereby granted, free of charge, to any person obtaining a copy of this software (Iperf) and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the
Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimers.
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimers in the documentation and/or other materials provided with the distribution.
Neither the names of the University of Illinois, NCSA, nor the names of its contributors may be used to endorse or promote products derived from this
Software without specific prior written permission. THE SOFTWARE IS
PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
2131352
Rev 1.0 Apr.10
Preface
NONINFRINGEMENT. IN NO EVENT SHALL THE CONTIBUTORS OR
COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR
THE USE OR OTHER DEALINGS IN THE SOFTWARE.
miniupnpd License
Copyright (c) 2006-2008, Thomas BERNARD
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
• Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
• Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
• The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
OpenSSL License
Copyright (c) 1998-2007 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1.
Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2.
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3.
All advertising materials mentioning features or use of this software must display the following acknowledgment:
4.
“This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)”
5.
The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this software without prior written
11
Clear Spot 4G+ User Guide permission. For written permission, please contact [email protected].
6.
Products derived from this software may not be called “OpenSSL” nor may
“OpenSSL” appear in their names without prior written permission of the
OpenSSL Project.
7.
Redistributions of any form whatsoever must retain the following acknowledgment:
“This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND
ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
This product includes cryptographic software written by Eric Young
([email protected]). This product includes software written by Tim Hudson
Original SSLeay License
Copyright (C) 1995-1998 Eric Young ([email protected])
All rights reserved.
This package is an SSL implementation written by Eric Young
The implementation was written so as to conform with Netscapes SSL.
This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the
SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson
Copyright remains Eric Young's, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
12 2131352
Rev 1.0 Apr.10
Preface
1.
Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.
2.
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3.
All advertising materials mentioning features or use of this software must display the following acknowledgement:
“This product includes cryptographic software written by Eric Young
The word ‘cryptographic’ can be left out if the rouines from the library being used are not cryptographic related :-).
4.
If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement:
“This product includes software written by Tim Hudson ([email protected])”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.]
PPPD License
Copyright (c) 1984-2000 Carnegie Mellon University. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1.
Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2.
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3.
The name “Carnegie Mellon University” must not be used to endorse or promote products derived from this software without prior written permission.
For permission or any legal details, please contact
Office of Technology Transfer
Carnegie Mellon University
5000 Forbes Avenue
13
Clear Spot 4G+ User Guide
14
Pittsburgh, PA 15213-3890
(412) 268-4387, fax: (412) 268-7395 [email protected]
4.
Redistributions of any form whatsoever must retain the following acknowledgment:
“This product includes software developed by Computing Services at Carnegie Mellon University (http://www.cmu.edu/computing/).”
CARNEGIE MELLON UNIVERSITY DISCLAIMS ALL WARRANTIES WITH
REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL CARNEGIE
MELLON UNIVERSITY BE LIABLE FOR ANY SPECIAL, INDIRECT OR
CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER
RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION,
ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
OF THIS SOFTWARE.
Copyright (c) 1999-2004 Paul Mackerras. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1.
Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2.
The name(s) of the authors of this software must not be used to endorse or promote products derived from this software without prior written permission.
3.
Redistributions of any form whatsoever must retain the following acknowledgment:
“This product includes software developed by Paul Mackerras
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL WARRANTIES WITH
REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL THE AUTHORS BE
LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR
ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR
PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR
OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH
THE USE OR PERFORMANCE OF THIS SOFTWARE.
PPPStats License
Copyright (c) 1989 Regents of the University of California.
All rights reserved.
Redistribution and use in source and binary forms are permitted provided that the above copyright notice and this paragraph are duplicated in all such forms and that any documentation, advertising materials, and other materials related to such distribution and use acknowledge that the software was developed by the
University of California, Berkeley. The name of the University may not be used to endorse or promote products derived from this software without specific prior written permission.
2131352
Rev 1.0 Apr.10
Preface
THIS SOFTWARE IS PROVIDED “AS IS” AND WITHOUT ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR
PURPOSE.
PPPDump License
Copyright (c) 1999 Paul Mackerras. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1.
Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2.
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3.
The name(s) of the authors of this software must not be used to endorse or promote products derived from this software without prior written permission.
4.
Redistributions of any form whatsoever must retain the following acknowledgment:
“This product includes software developed by Paul Mackerras
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL WARRANTIES WITH
REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL THE AUTHORS BE
LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR
ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR
PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR
OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH
THE USE OR PERFORMANCE OF THIS SOFTWARE.
SSH2 License
Copyright (c) 2004-2007 Sara Golemon <[email protected]>
Copyright (C) 2006-2007 The Written Word, Inc.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Neither the name of the copyright holder nor the names of any other contributors may be used to endorse or promote products derived from this software without specific prior written permission.
15
Clear Spot 4G+ User Guide
16
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
UUID License
Copyright (c) 2004-2008 Ralf S. Engelschall <[email protected]>
Copyright (c) 2004-2008 The OSSP Project <http://www.ossp.org/>
This file is part of OSSP uuid, a library for the generation of UUIDs which can found at http://www.ossp.org/pkg/lib/uuid/
Permission to use, copy, modify, and distribute this software for any purpose with or without fee is hereby granted, provided that the above copyright notice and this permission notice appear in all copies.
THIS SOFTWARE IS PROVIDED “AS IS” AND ANY EXPRESSED OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE AUTHORS AND COPYRIGHT HOLDERS AND
THEIR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
Zlib License
Copyright (C) 1995-2010 Jean-loup Gailly and Mark Adler
This software is provided ‘as-is’, without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software.
Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:
1.
The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an
2131352
Preface
Copyright
Trademarks
acknowledgment in the product documentation would be appreciated but is not required.
2.
Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
3.
This notice may not be removed or altered from any source distribution.
Jean-loup Gailly
Mark Adler
© 2010 Sierra Wireless. All rights reserved.
AirCard and “Heart of the Wireless Machine” are registered trademarks of Sierra
Wireless. AirPrime, AirLink, AirVantage, Sierra Wireless, the Sierra Wireless logo,
TRU-Install, and the red wave design are trademarks of Sierra Wireless.
Windows
®
and Windows Vista
®
are registered trademarks of Microsoft
Corporation.
Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries.
QUALCOMM
®
is a registered trademark of QUALCOMM Incorporated. Used under license.
Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.
Wi-Fi, WPA, and WPA2 are registered marks of the Wi-Fi Alliance.
QUALCOMM® is a registered trademark of QUALCOMM Incorporated.
Other trademarks are the property of their respective owners.
Contact
Information
Sales Desk:
Post:
Fax:
Web:
Phone:
Hours:
E-mail:
1-604-232-1488
8:00 AM to 5:00 PM Pacific Time [email protected]
Sierra Wireless
13811 Wireless Way
Richmond, BC
Canada V6V 3A4
1-604-231-1109 www.sierrawireless.com
Additional
Information and
Updates
For up-to-date product descriptions, documentation, application notes, firmware upgrades, troubleshooting tips, and press releases, visit www.sierrawireless.com
.
Rev 1.0 Apr.10
17
Clear Spot 4G+ User Guide
Revision
History
Revision number
Release date
Changes
1.0
Apr 10 Initial release
18 2131352
Contents
Components of your device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Getting Started With Your Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Using the AC Charger with USB Port . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Charging Through a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Turning Your Device On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Turning Your Device Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Using the Power Button to Determine the Device State . . . . . . . . . . . . . 34
Controlling the Device Using the Power Button . . . . . . . . . . . . . . . . . . . . 34
Connecting to the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Changing the Password and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Rev 1.0 Apr.10
19
Clear Spot 4G+ User Guide
20
Activating and Using Your Network Service . . . . . . . . . . . . . . . . . . . . . . 40
Requirements for a USB Tethered Connection . . . . . . . . . . . . . . . . . . . . 43
Making a Tethered Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Browser Interface Home Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Displaying the Home Page of the Device . . . . . . . . . . . . . . . . . . . . . . . . 46
Logging On as an Administrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Turning Your Device Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
3G Network Update Available . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Software Update Available . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Launching Your Network Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Sharing Your Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Ending Your Network Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Mobile Broadband Information and Settings . . . . . . . . . . . . . . . . . . . . . . 53
Wi-Fi Users Information and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Battery Information and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Sounds Information and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Buttons Along the Top of the Home Page . . . . . . . . . . . . . . . . . . . . . . . . 59
2131352
Contents
Buttons Below the Virtual Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Before Using the microSD Card Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Removing a microSD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Accessing the microSD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Automatically Checking for Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Manually Checking for Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Upgrade Firmware From a File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Battery and USB Power Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Turning the LCD On or Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Setting the LCD Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Setting the LCD Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Enabling and Disabling the LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Enabling and Disabling Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Enabling and Disabling Sounds for Specific Events . . . . . . . . . . . . . . . . 73
Changing the Administrator Password . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Automatic Login ("Remember Me") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Accessing the Advanced Settings Window . . . . . . . . . . . . . . . . . . . . . . . 76
Rev 1.0 Apr.10
21
Clear Spot 4G+ User Guide
22
SSID (Wi-Fi Network Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Host Name (Device Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Setting the Maximum Number of Wi-Fi Users . . . . . . . . . . . . . . . . . . . . . 90
Disabling Wi-Fi When Connected Through USB . . . . . . . . . . . . . . . . . . . 91
Viewing 3G Activation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Resetting the 3G/4G Configuration to Default Settings . . . . . . . . . . . . . . 92
Resetting the Software to Default Settings . . . . . . . . . . . . . . . . . . . . . . 103
Exporting and Importing Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Setting the Method Used for Time Acquisition . . . . . . . . . . . . . . . . . . . 107
Welcome to Your Device Window - Select an Option . . . . . . . . . . . . . . 108
2131352
Rev 1.0 Apr.10
Contents
Visiting the CLEAR Website . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Contacting Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
How Can I Tell I'm Connected to 3G/4G? . . . . . . . . . . . . . . . . . . . . . . . 110
How Do I Connect to Wi-Fi? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
What Do I Do if I Forgot the Wi-Fi Password? . . . . . . . . . . . . . . . . . . . . 110
What Do I Do if I Forgot the Administrator Password? . . . . . . . . . . . . . 111
How Do I Access My Corporate Network Through a VPN? . . . . . . . . . . 111
Are Terminal Sessions Supported? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Improving Signal Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Improving 3G Network Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Improving Wi-Fi Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Finding the MAC Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Insufficient Signal Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Messages Displayed on the Device LCD . . . . . . . . . . . . . . . . . . . . . . . . 117
Cannot Connect to Wi-Fi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Cannot Display the Home Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Cannot Connect to the 3G/4G Network . . . . . . . . . . . . . . . . . . . . . . . . . 120
Cannot Check for Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Sounds are Enabled, but the Device Doesn't Generate Any Sounds . . 120
23
Clear Spot 4G+ User Guide
Technical Specifications, Safety Information, and
Radio Frequency and Electrical Specifications . . . . . . . . . . . . . . . . . . . 121
Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Mechanical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
24 2131352
1: Device Basics
Your Clear Spot 4G+ personal hotspot allows you to easily connect to the Internet and to share your 3G/4G connection with others.
This user guide describes how to set up your device and use the browser interface to:
• View the status of your device.
• View and change the settings of your device and the browser interface.
It also describes your device (its various connectors and buttons).
1
Your Device
The Clear Spot 4G+ personal hotspot provides a simple way to use your 3G/4G Internet connection with any Wi-Fi-enabled device, and to share your Internet connection with friends and family.
Rev 1.0 Apr.10
25
Clear Spot 4G+ User Guide
Components of your device
Your device consists of these main components:
• Wi-Fi access point
The Wi-Fi access point connects your computers and other Wi-Fi-enabled devices to your device.
• 3G modem
The 3G modem connects your device to the Internet via the 3G (CDMA 1X/
EVDO) network (more widely available, compared to 4G).
• 4G modem
The 4G modem connects your device to the Internet via the 4G (WiMAX) network (newer technology and faster speeds, compared to 3G).
• Routing hardware
The routing hardware handles traffic between the 3G/4G modems, the Wi-Fi access point, and the Wi-Fi network.
3G and 4G Networks
These wireless networks connect you to the Internet. Depending on your coverage area, you may have:
• Both 3G and 4G coverage
• Only 3G coverage
• Only 4G coverage.
Your device automatically connects to the fastest network that is available to you.
If you have both 3G and 4G coverage and your connection happens to get disrupted, your device can automatically switch to the other network. For more information, see
"Configuring the 3G/4G Connection Preferences" on page 54
.
Download speeds
Actual speeds depend on several factors, including network conditions.
Wireless mode
3G (EV-DO Rev 0)
3G (EV-DO Rev A)
4G
Maximum downlink speeds
2.4 Mbps
3 Mbps
10 Mbps
Typical downlink speeds
400-700 kbps
0.6-1.4 Mbps
3-6 Mbps
26 2131352
Rev 1.0 Apr.10
Device Basics
Package Contents
Your package includes:
• Clear Spot 4G+ personal hotspot by Sierra Wireless
• Battery compartment cover
• Rechargeable battery
• Power adapter
• USB cable
• Quick Start guide
Care and Maintenance
As with any electronic device, you should handle this device with care to ensure reliable operation. Follow these guidelines in using and storing the device:
• Protect the device from liquids, dust, and excessive heat.
• Do not handle or operate the device while driving or operating a vehicle.
Doing so may distract you from properly operating the vehicle. In some jurisdictions, operating communication devices while in control of a vehicle is a criminal offense.
• Do not apply adhesive labels to the device. They may cause the device to overheat and may alter the antenna's performance.
About This Guide
This user guide provides you with all the information you'll need to install and use your Clear Spot 4G+ personal hotspot.
The printed Quick Start guide that comes with the Clear Spot 4G+ personal hotspot should be sufficient for most installations.
• Chapter 1 (which you are reading) gives you an overview of the device.
• Chapter 2 describes the buttons, connectors, and other components of the
device. (See "Your Device" on page 29 ).
• Chapter 3 provides step-by-step instructions for setting up the device. (See
"Installing and Setting Up the Device" on page 37).
• Chapter 4 describes common tasks for your device. (See
"Using Your Device" on page 43
).
• Chapter 5 describes advanced configuration of the device and the browser
interface. (See "Settings" on page 71
).
• Chapter 6 contains frequently asked questions, troubleshooting tips, and
resources for getting help. (See "Resources" on page 109
).
• Chapter 7 lists the electrical, radio frequency, and other parameters of the device for those who require technical information, as well as safety information and regulatory information. (See
"Technical Specifications, Safety
Information, and Regulatory Information" on page 121).
27
Clear Spot 4G+ User Guide
Getting Started With Your Device
System Requirements
• One or more computers that support Wi-Fi (802.11b/g)
• Web browser (required if you'll be using the browser interface to view status and to configure settings). The following browsers are supported:
· Internet Explorer (version 6.0 or higher)
· Mozilla Firefox (version 2.0 or higher)
· Google Chrome (version 2.0.172.28 or higher)
· Apple Safari (version 2.0 or higher)
· Opera version 9.64
• If you'll be connecting the device through USB:
· Computer running Windows 7, Windows Vista, Windows XP, or Mac (OS X
10.4.x or higher)
· USB 2.0 slot
28 2131352
2: Your Device
Battery
The battery compartment is on the back of the device. The battery is replaceable.
If you need a new battery, visit the Sierra Wireless online store at https://www.sierrawireless.com/eStore/ .
Installing the Battery
1.
Remove the battery compartment cover.
2
Rev 1.0 Apr.10
29
Clear Spot 4G+ User Guide
2.
Align the battery contact points with those inside the battery compartment, and insert the battery into the device.
3.
Replace the battery compartment cover.
Connecting Through USB
30
Note: If you’ll be using USB for data transfer (and not just for charging the device), you must install the device driver. See
"Making a Tethered Connection" on page 43 .
2131352
Rev 1.0 Apr.10
Your Device
Use the USB cable to connect the device to your computer when:
• You want to charge the device, but you don't want to use the power adapter, or the power adapter is not available.
• Your computer does not have Wi-Fi.
• You want to block others from using the device. (See
Connected Through USB" on page 91
.)
To connect the device to your computer:
1.
Insert the larger (USB) end of the USB cable into the computer.
2.
Insert the other (Micro B) end of the USB cable into the USB connector on the side of the device.
Charging the Device
You need to recharge your device's battery periodically. You can continue using your device while it is charging.
To charge the battery, you have two options, as shown in the drawing that follows
— you can connect the device to an AC charger (faster way to charge). See
"Using the AC Charger with USB Port" on page 32
. Alternatively, you can connect the device to a computer (slower way to charge). See
.
31
Clear Spot 4G+ User Guide
Using the AC Charger with USB Port
1.
Insert the smaller (Micro B) end of the USB cable into the USB connector on the side of the device.
2.
Insert the other (USB) end of the USB cable into the power adapter.
3.
Insert the power adapter into an electrical outlet.
When charging, the LCD shows
"Charging... xx% complete".
and, if the device is off, displays a message
When the device is charged, the LCD shows:
•
•
(if the device is on)
and the message "Fully charged" (if the device is off).
Charging Through a Computer
32
Note: Charging through a computer usually takes longer than charging through the power adapter.
Note: If you’ll be using USB for data transfer (and not just for charging the device), you must install the device driver. See
"Making a Tethered Connection" on page 43 .
2131352
Rev 1.0 Apr.10
Your Device
Note: If you’re using Mac OS X 10.4.x, after you connect the device you may see a warning message that your computer is running on UPS backup battery and that you should perform a computer shutdown. You can continue with your work. To prevent this message from being displayed, install the device driver. See
.
1.
Ensure the computer is turned on.
2.
Insert the larger (USB) end of the USB cable into the computer.
3.
Insert the other (Micro B) end of the USB cable into the USB connector on the side of the device.
When charging, the LCD shows .
When the device is charged, the LCD shows .
Power Button
Turning Your Device On
1.
Ensure that:
· The device has a charged battery inserted.
— or —
· The device is connected to the power adapter or a computer (through the
USB cable), as shown in the drawing on
2.
If the device LCD is blank, press and hold the power button for two seconds.
Turning Your Device Off
• Press and hold the power button for 2 seconds.
33
Clear Spot 4G+ User Guide
Using the Power Button to Determine the Device State
The power button on the device also indicates the device's status, as shown in the following table.
Description Your action
Power button
Not lit • The device is turned off, and may or may not be charging.
• The device is turned on, but you have turned off the LED.
• To turn the device on, press and hold the power button for two seconds.
• [OPTIONAL]: Turn on the LED. See
"Enabling and Disabling the LED" on page 72 .
No action required.
Lit, flashing
(approximately every
4 seconds)
Lit, flashing
(approximately every
30 seconds)
The device is turned on, and the LED is enabled.
The device is in standby (low power) mode.
The following are off: LCD, Wi-Fi radio, 3G/
4G radios.
For more information, see
To exit standby mode:
Connect the device to the power adapter or computer, through the USB cable.
— or —
Press the power button .
Controlling the Device Using the Power Button
Type of press
Quick press
Quick double-press
Long press (press and hold for two seconds)
Result
• The device leaves standby (low power) mode.
• The LCD wakes up (turns on) if it was enabled but dormant. (The LCD turns dark, after a configurable time of inactivity.)
• A displayed message is confirmed or acknowledged.
• Display of the Wi-Fi network name (SSID) and password is turned off.
• The LCD wakes up (turns on) if it was enabled but dormant. (The LCD turns dark, after a configurable time of inactivity.)
• The Wi-Fi network name (SSID) and password are briefly displayed. See
Password Reminder" on page 88 .
The device turns on or off.
34 2131352
Rev 1.0 Apr.10
Your Device
LCD
If the LCD is not lit, see "Turning Your Device On" on page 33 .
Interpreting the LCD
The LCD shows icons and text that reflect the status of the device and your connection.
A B C D E
F
G
F
G
D
E
A
B
C
Signal strength
3G/4G status
Alerts
Number of Wi-Fi users
Battery status
Device name. Message area.
Amount of data transferred; connection duration. Message area.
Tip:
Most of the LCD icons and messages are also shown on the Virtual Device (page 47)
and Mini Window (page 47). See also "Messages Displayed on the Device LCD" on page 117 .
35
Clear Spot 4G+ User Guide
Mute Switch
The mute switch is used to turn on or off sounds from the device. The mute switch is located on the side of the device:
Tip:
microSD Card Slot
Your device supports a microSD™ card (sold separately) for file sharing and transfer or storage. The microSD slot is located on the same side of the device as the USB connector. Your computer recognizes the microSD card as a removable storage device. The device supports microSD cards up to 16 GB.
Note: Using microSD cards larger than 16 GB can cause data loss and damage your device.
36 2131352
3: Installing and Setting Up the Device
Setting Up the Device
1.
Install the battery, as described in
"Installing the Battery" on page 29.
2.
Connect the device to the AC charger, as described in
AC Charger with USB Port" on page 32.
3.
Plug the AC charger into an electrical outlet.
4.
Important: Charge the device until the battery icon is full ( ).
Connecting to the Network
1.
Ensure you are in the CLEAR 3G or 4G coverage area.
2.
If you have a LAN connection, disconnect it.
3.
Ensure your computer's Wi-Fi is turned on.
4.
If the device LCD displays "Charging", "Charged", or "Powered off", press and hold the power button for two seconds.
3
Rev 1.0 Apr.10
5.
Wait until the device LCD displays "Connect your computer to
Wi-Fi network," followed by the network name (SSID) and password. This may take several seconds.
6.
On your computer, connect to the Wi-Fi network listed on the device LCD. If you don't know how to do this, see
I Connect to Wi-Fi?" on page 110
. After you’ve connected to the
Wi-Fi network, the device LCD displays "Open any web page to continue setup."
7.
Open your Web browser. The "Welcome to your Clear Spot 4G+" window opens.
Note: This window displays the administrator password and the address of the device home page. Please remember this information or write it down in a safe place.
37
Clear Spot 4G+ User Guide
This window provides several options.
• To keep the default settings of the device, click one of the following:
· The Internet (to start surfing)
· My Clear Spot 4G+'s home page (to view the device status, customize
settings). Proceed to "Using Your Device" on page 43 .
• To change security settings, click Set up my Clear Spot 4G+ .
Changing the Password and Settings
During the device setup, you can select Set up my Clear Spot 4G+ to change the settings for the:
• Administrator password
This password is used to log in to the home page, where you can view and customize your device settings. The default password is " admin ".
Choose something easy-to-remember (yet not easily guessed by others). If you forget this password, you’ll need to reset the device to its default settings and go through
the device setup (as described in "Setting Up the Device" on page 37).
Your administrator password must be 1–20 characters long.
• Wi-Fi network name (SSID)
This name is visible to other Wi-Fi-enabled devices, and is used to identify your Wi-Fi network. The length of the Wi-Fi network name (SSID) depends on other settings of the browser interface. (See the Help bubble that's displayed when you move the cursor to the SSID input field.)
• Wi-Fi security
The default setting is WEP 64 Bit Open. To select another option, click More options . See
"Wi-Fi Security Options" on page 39.
• Wi-Fi password
The maximum length of this field is determined by the Wi-Fi security option
(the previous item). (See the Help bubble that's displayed when you move the cursor to the Wi-Fi password field.)
If you'll be sharing your Internet connection with others, you'll have to give the
Wi-Fi password to others; don't use your banking or other important passwords. Also, don't use a password that's easily guessed by others.
From this window you can also enable the Password Reminder feature, which is useful if you forget the Wi-Fi password. See
"Wi-Fi Password Reminder" on page 88
.
Tip: Help information on each field appears (in a bubble) when you move the cursor into the field.
You can display this window any time, by clicking Admin Setup ( interface.
) in the browser
After you change the settings and click Submit , the device restarts and displays updated information on its LCD. Follow the instructions on the LCD, and proceed to
"Your Device is Now Restarting" on page 40.
38 2131352
Rev 1.0 Apr.10
Installing and Setting Up the Device
Wi-Fi Security Options
If you click More options (after having clicked Set up my Clear Spot 4G+ , during the device setup), a window with four Wi-Fi security options opens.
Note: All the devices used with the Clear Spot 4G+ personal hotspot must support the selected security type.
Going from no security to stronger security, the options are:
• None
No security (no password is required to access the Wi-Fi network); not recommended. Anyone may access your device and use your Internet connection
(you are responsible for payment for data usage).
• WEP-64 Bit
Lower security. Works with older and newer Wi-Fi devices. Recommended only if any of your devices don't support WPA or WPA2.
• WPA-Personal
A strong security standard, supported by most Wi-Fi devices.
• WPA2-Personal
A stronger, newer security standard. Limited to newer Wi-Fi devices.
If the above options don't meet your requirements, click I don't see what I want...
.
Expanded Wi-Fi Security Options
If you display the Security panel of the Wi-Fi tab of the Advanced Settings window or if you click I don't see what I want...
(from the Wi-Fi Security Options window during the device setup), a window with an expanded list of Wi-Fi security options opens.
Note: All the devices used with the Clear Spot 4G+ personal hotspot must support the selected security type.
The options are:
• None
No security (no password is required to access the Wi-Fi network); not recommended. Anyone may access your device and use your Internet connection
(you are responsible for payment for data usage).
• WEP-64 Bit - Shared
Lower security. Works with older and newer Wi-Fi devices. Recommended only if any of your devices don't support WPA or WPA2.
Shared WEP uses the same key for encryption and authentication; some consider shared WEP to be less secure than open WEP.
• WEP-128 Bit - Shared
Lower security. Works with older and newer Wi-Fi devices. Recommended only if any of your devices don't support WPA or WPA2.
Shared WEP uses the same key for encryption and authentication; some consider shared WEP to be less secure than open WEP.
• WEP-64 Bit - Open
39
Clear Spot 4G+ User Guide
Lower security. Works with older and newer Wi-Fi devices. Recommended only if any of your devices don't support WPA or WPA2.
Open WEP uses the key for encryption, but not for authentication.
• WEP-128 Bit - Open
Lower security. Works with older and newer Wi-Fi devices. Recommended only if any of your devices don't support WPA or WPA2.
Open WEP uses the key for encryption, but not for authentication.
• WPA-Personal - TKIP
A strong security standard, supported by most Wi-Fi devices.
• WPA-Personal - TKIP/AES
A strong security standard, supported by most Wi-Fi devices.
• WPA2-Personal - AES
A stronger, newer security standard. Limited to newer Wi-Fi devices.
• WPA2-Personal - TKIP/AES
A stronger, newer security standard. Limited to newer Wi-Fi devices.
• WPA/WPA2 Personal (recommended setting)
Wi-Fi devices that use either WPA or WPA2 can connect to the device. Supported by most Wi-Fi devices.
Your Device is Now Restarting
The "Your device is now restarting" window opens if you've clicked the Set up my
Clear Spot 4G+ option and then clicked Submit .
The changes take effect after the device restarts automatically.
It's recommended you write down the following information that's displayed in the window:
• Wi-Fi network name
• Wi-Fi password
As described in the window,
1.
Wait until the device LCD displays "Connect your computer to Wi-Fi Network".
2.
Connect your computer to the Wi-Fi network, using the information you've written down. (If you don't know how to do this, see
).
3.
After the Wi-Fi connection was successfully established, click the Click here text in the window.
Activating and Using Your Network Service
Note: If you're able to connect to 3G, you are already set up to use CLEAR service on the
3G network; no further action is needed. Proceed to "Using Your Device" on page 43 .
Before using your device, you must have a CLEAR wireless network account set up. The process of setting up an account is called activation . When the device starts up, it will detect whether the device has been configured with an account
("preactivated"). If it has not, the activation process starts automatically.
40 2131352
Rev 1.0 Apr.10
Installing and Setting Up the Device
In most cases, the activation process will be seamless, not requiring any action from your part; in some cases, you won't even see any activation-related messages displayed on the device LCD.
Initiating Activation of Your Device for 3G
In rare cases, the device LCD and the home page may indicate that activation is required:
• The LCD displays "3G Activation failed".
• The home page displays the alert "3G Activation Required".
Note: You will still be able to connect to the Internet, when you have 4G coverage.
To activate your device for 3G:
1.
In the Admin Login section (in the upper left area of the home page), enter the administrator password (1–20 characters/numbers). (The default password is
"admin".)
2.
Click OK .
3.
Click the alerts icon to display the alert window.
4.
If more than one alert is available, use the and buttons (at the top of the alert window) to browse to the "3G Activation Required" alert.
5.
In the alert, click Activate now .
If the activation fails, contact CLEAR. See
"Contacting Customer Service" on page 109 .
41
Clear Spot 4G+ User Guide
42 2131352
4: Using Your Device
Connecting Through USB
TRU-Install
TRU-Install™ is a Sierra Wireless feature that installs the necessary drivers the first time you connect the device to your Windows or Mac computer through the USB cable. (For details, see
Tethered Connection" below.) An installation CD is not required.
By default, TRU-Install is enabled.
To change the setting:
1.
Ensure you're logged in to the home page.
2.
Click Advanced settings > Device > Basic .
3.
Select a value for TRU-Install .
Requirements for a USB Tethered Connection
Your device supports a direct connection through a USB cable to a
Windows or Mac computer. (This is commonly referred to as a
"tethered" connection.)
Making a Tethered Connection
4
Rev 1.0 Apr.10
Note: If you’ll be using USB for data transfer (and not just for charging the device), you must install the device driver (see below). No installation CD is required — the device supports the Sierra Wireless TRU-Install feature.
43
Clear Spot 4G+ User Guide
Note: If you’re using Mac OS X 10.4.x, after you connect the device you may see a warning message that your computer is running on UPS backup battery and that you should perform a computer shutdown. You can continue with your work. To prevent this
message from being displayed, install the device driver (see "Mac" , below).
Windows
1.
Ensure the device is turned on.
2.
Connect the device to your computer through the USB cable.
3.
If the TRU-Install window is not displayed, in Windows Explorer browse to the
entry (under My Computer), then browse to the Win folder and run Setup.exe
.
— or —
If you’re running Windows Vista and the AutoPlay window opens, click Run setup.exe
.
4.
In the TRU-Install window, click OK .
5.
Go through the installation of the Sierra Wireless USB driver. (Follow the instructions on the screen.)
Mac
1.
Ensure the device is turned on.
2.
Connect the device to your computer through the USB cable.
3.
In the window that appears, double-click the .pkg
file.
4.
Go through the installation of the Sierra Wireless USB driver. (Follow the instructions on the screen.)
5.
When prompted for your password, enter your Mac password.
Connecting the Device to Your Computer
1.
Insert the larger (USB) end of the USB cable into your computer.
2.
Insert the other (Micro B) end of the USB cable into the USB connector on the side of the device.
Browser Interface Home Page
The home page is the entry page of the browser interface that lets you:
• Display status information for your device and your data connection.
• Launch and end a network connection
• Change the settings for your device and your data connections (if you're logged in).
44 2131352
Using Your Device
A
• Access additional resources (the user guide and the Important Information document).
B C
Rev 1.0 Apr.10
D
E
A
B
C
D
E
F
F
When you click an icon or the text next to it, a window opens to the right (see the screenshot on
page 52 ). The window contains additional status information and,
if you're logged in, commonly-used configurable settings.
See "Vertical Row (of Icons and Text)" on page 52
.
Use this area to enter the administrator password and log in. When you're logged in, you can change settings.
See "Logging On as an Administrator" on page 46 .
Clicking one of these buttons displays a window or a menu. See
"Buttons Along the Top of the Home Page" on page 59 .
This is the Virtual Device; it reflects the status of your Clear Spot 4G+ personal hotspot. If you click the image, a movable Mini Window is opened.
See "Virtual Device" on page 47 and "Mini Window" on page 47
.
A handy way to turn the device off, especially if, for example, you're in an airplane before takeoff, and the device is in your overhead bag.
Available only if you're logged in.
Disconnects a connection, or connects (if currently there's no connection).
Available only if you're logged in.
45
Clear Spot 4G+ User Guide
Displaying the Home Page of the Device
Note: You can display the home page only when your device is turned on and you have established a connection to it (through Wi-Fi or through the USB cable).
To display the home page, type one of the following in the address bar of your
Web browser:
• http://clearspot
• SSID value (field in Advanced settings > Wi-Fi > Network and also in Advanced settings > Router > LAN ).
Note: If you're using the Google Chrome Web browser, after typing in the address bar, press the Down Arrow key and then the Enter key. (If you press only the Enter key, a
Google search is started, using the information you typed in.)
If your Web browser displays an error message, see "Cannot Display the Home
.
Logging On as an Administrator
You don't need to log in to access and use the home page. However, when you're logged in:
• Additional information appears in the window that appears when you click an item on the left side of the home page. See
"Vertical Row (of Icons and Text)" on page 52 .
• You can access the Advanced Settings window, where you can modify additional settings.
• You can rerun the device setup, if required ( Admin Setup [ ]).
• You can install updates.
To log in:
1.
Ensure that nobody else is already logged in — other people can use the home page at the same time, but only one user can be logged in.
2.
In the Admin Login section (in the upper left area of the home page), enter the administrator password (1–20 characters/numbers). (The default password is
"admin". It's recommended you change the password, if you haven't already.)
3.
Click OK .
After a certain time, you will be automatically logged off (timeout security feature), unless you select Remember me (below the password field). For more information,
see "Automatic Login ("Remember Me")" on page 75
.
46 2131352
Using Your Device
Virtual Device
The right half of the home page contains an image of your device.
This is a "virtual device" — it reflects most of the icons and text displayed on the real device.
Mini Window
If you click the virtual device on the home page, the Mini Window opens — an image of the device in a separate Web browser window.
Rev 1.0 Apr.10
Similar to the virtual device, the Mini Window reflects most of the icons and text displayed on the real device.
47
Clear Spot 4G+ User Guide
To save space on your monitor, you can close the home page and move the Mini
Window to the side of your monitor. Then you can use the window to keep an eye on the status of your device and connection. (To reopen the home page, click the
Home link.)
If you're logged in, the window has a Connect or Disconnect button, and a Power Off button.
Turning Your Device Off
From the Home page:
1.
Ensure you're logged in to the home page.
2.
Click Power Off (below the Virtual Device).
From the Mini Window:
1.
Ensure you're logged in to the home page.
2.
Click Power Off .
From the device:
1.
Press and hold the power button for 2 seconds.
Note: You can turn the device on only by using the device power button.
48
Alerts
Displaying Alerts
The alerts icon indicates whether there are any alerts (messages that require your attention).
The icon is on the left side of the home page.
Click the icon to display the Alert window. If more than one alert is available:
• The higher priority alert opens.
• When you close an alert, the next alert opens.
• You can use the and buttons (at the top of the alert window) to view other alerts.
The options and instructions shown in the alert window depend on the alert event.
Please read the instructions carefully. They may state, for example, that you have to reconnect to Wi-Fi after an update is installed.
3G Activation Required
If only 3G coverage is available, you won't be able to connect to the Internet until
3G activation has been completed.
To activate 3G on your device:
1.
Ensure you have 3G coverage.
2131352
Rev 1.0 Apr.10
Using Your Device
2.
In the Admin Login section (in the upper left area of the home page), enter the administrator password (1–20 characters/numbers). (The default password is
"admin".)
3.
Click OK .
4.
Click the alerts icon to display the alert window.
5.
If more than one alert is available, use the and buttons (at the top of the alert window) to browse to the "3G Activation Required" alert.
6.
In the 3G Activation Required alert window, click Activate now . (Activation is then performed over the network; no user interaction is required.)
• If activation is successful, "Activation complete!" is displayed. You can now connect to the 3G network. If the connection is not established automatically, click Connect on the home page or Mini Window.
• If activation was not successful, "Activation failed" is displayed. Retry the activation. If it is not successful, prepare the following, and contact CLEAR:
· Your billing information.
· ESN of the device (displayed on the packaging, on the device [under the battery], and at Advanced settings > Device > About ).
3G Network Update Available
The 3G Network Update Available alert appears if a PRL update or 3G profile update is available for your device. The update may improve your 3G network service.
Note: During installation of the update:
• DO NOT turn off or unplug the device.
• Your 3G connection won’t be available. (Your 4G connection won't be affected.)
To install the update:
1.
Ensure you have 3G coverage.
2.
In the Admin Login section (in the upper left area of the home page), enter the administrator password (1–20 characters/numbers). (The default password is
"admin".)
3.
Click OK .
4.
Click the alerts icon to display the alert window.
5.
If more than one alert is available, use the and buttons (at the top of the alert window) to browse to the "3G Activation Required" alert.
6.
In the 3G Network Update Available alert window, click Update now .
SD Card Error
If you're having problems reading from the microSD card, or if the SD Card Error alert window opens or the device LCD displays "SD Card error", try the following:
1.
Remove and reinsert the microSD card.
2.
If the card is still not working, try it in the microSD slot of another computer.
49
Clear Spot 4G+ User Guide
If it works in the other device, the card slot on your Clear Spot 4G+ personal hotspot may have a problem.
If the card doesn’t work in the other computer, try one of the following:
· Use a different microSD card.
· Reformat your card.
Note: The formatting procedure erases all the data on the microSD card, after which the files CANNOT be retrieved. To prevent the loss of important data, please check the contents before you format the microSD card.
Software Update Available
The update may improve performance and add or modify features.
Note: During installation of the update, your Internet and Wi-Fi connections won’t be available.
When the installation is complete, you will need to reconnect to Wi-Fi.
To install the update:
1.
Ensure your device is connected to the power adapter or computer, through the USB cable.
Note: If you’ll be using USB for data transfer (and not just for charging the device), you must install the device driver. See
"Making a Tethered Connection" on page 43 .
2.
In the Admin Login section (in the upper left area of the home page), enter the administrator password (1–20 characters/numbers). (The default password is
"admin".)
3.
Click OK .
4.
Click the alerts icon to display the alert window.
5.
If more than one alert is available, use the and buttons (at the top of the alert window) to browse to the "3G Activation Required" alert.
6.
In the Software Update Available alert window, click Update Options .
7.
Read the information in the Software Installation Options window.
8.
To install the updates, click Download and install now .
— or —
If you are not in a strong signal area, make a note of the URL displayed in the window and click I’ll get the update later . At a later time, access the URL to
download the update to your computer, and then "Upgrade Firmware From a
9.
When the installation is complete, reconnect to Wi-Fi. See
"How Do I Connect to Wi-Fi?" on page 110 .
50 2131352
Rev 1.0 Apr.10
Using Your Device
Your Network Connection
Launching Your Network Connection
After the device powers on and boots up, a connection to the 3G/4G network is launched automatically, unless you've disabled Connect Automatically .
You will need to manually launch a connection if:
• The connection was not successful.
• You’ve disabled auto-connect.
• You’ve manually ended a connection (by clicking Disconnect ).
To launch a connection:
• Click Connect on the Virtual Device on the home page (you must be logged in).
— or —
Click Connect in the Mini Window (you must be logged in).
— or —
If the device LCD displays "Disconnected from 3G/4G network. Connect now?", press the power button on the device.
Sharing Your Connection
For others to share your network connection:
1.
Provide the Wi-Fi network name and password to them.
2.
On their computer, users must connect to the Wi-Fi network of the Clear Spot
4G+ personal hotspot. See
"How Do I Connect to Wi-Fi?" on page 110 .
Ending Your Network Connection
1.
Ensure you're logged in to the home page.
2.
Click Disconnect on the Virtual Device or in the Mini Window. See
Device" on page 47 and "Mini Window" on page 47 .
Note: The Wi-Fi connection is still available, so users can, for example, share files by using a microSD card.
51
Clear Spot 4G+ User Guide
Vertical Row (of Icons and Text)
The left part of the home page has a vertical row of icons and text, starting with the signal strength indicator .
Most of these icons are also shown on the physical device and Virtual Device
(
). Hover the mouse over an icon; the corresponding icon on the Virtual
Device is highlighted.
If you click an icon or the text, a window opens with additional information, as shown in the following screenshot.
52
If you're logged in, the window may also display configurable settings.
2131352
Rev 1.0 Apr.10
Using Your Device
Tip: A more complete set of configurable settings is available in the Advanced Settings
window. See "Advanced Settings" on page 59 .
Signal Information
Icon
...
Description
No signal
Very weak signal
The number of bars reflects the signal strength: the more bars, the stronger the signal.
Excellent signal
Click the icon to display the Signal Quality window. The window displays:
• The active network: the network that is currently being used for your data connection. For example: "3G (EVDO Rev A)".
• 3G or 4G status:
· Connection status. For example: "Connected".
· Brief description of the signal strength. For example: "Good signal (60%)".
· Tables that show the coverage type, RSSI, and Ec/Io (for 3G) or CINR (for
4G).
RSSI reflects the signal strength of the network.
Ec/Io is a dimensionless ratio of the average power of a channel, typically the pilot channel, to the total signal power.
CINR stands for Carrier to Interference-plus-Noise Ratio, and is a measurement of signal effectiveness.
The first table also shows the type(s) of 3G service you have: 1X, 1xEV-DO, or both. (To determine whether you have EV-DO Rev. 0 or Rev. A service, use
the text near the 3G icon; see "Mobile Broadband Information and Settings" on page 53
.)
See also "Improving Signal Strength" on page 112 .
Mobile Broadband Information and Settings
The 3G or 4G icon indicates the service and connection state. Note that only one icon is shown (the active network).
Icon
or
or
or
Description
You have no service. Try the suggestions in "Cannot Connect to the 3G/4G Network" on page 120
.
You have service but are not connected.
You have service and are connected.
53
Clear Spot 4G+ User Guide
The text next to the icon displays the connection status, for example: "No service", or "3G (EVDO Rev A)".
Click the icon or text to display the Mobile Broadband Information window. The window displays:
• The active network: the network that is currently being used for your data connection. For example: "4G" or "3G (EVDO Rev A)".
• 3G and 4G status:
· Connection status. For example: "Connected".
· Brief description of the signal strength. For example: "Good signal (60%)".
• Connection Preferences (if you're logged in).
Configuring the 3G/4G Connection Preferences
The value determines which network(s) to connect to, and in what order:
• 4G Preferred — Connection can be established to either 3G or 4G; if both are available, 4G is used. This setting is recommended if your service provider has no data limit for 4G, but does for 3G, or you want to take advantage of the faster data transfer speeds of 4G.
• 4G Only — Connection can be established only to 4G.
• 3G Only — Connection can be established only to 3G.
If you don’t have 4G coverage, you can save power by selecting "3G Only".
To automatically connect to the network upon loss of connection or when the device powers on, select Connect Automatically .
Alert Information
The alerts icon indicates whether there are any alerts (situations that require your attention).
Note: To view alert information, you must be logged in. New alerts are checked upon device power-up. That is, if an event occurs, you won't be notified until the device is restarted.
Icon Description
No alerts are available.
One or more alert is available.
The text next to the icon indicates the number of alerts.
Click the icon or text to display the Alert window.
For more information, see "Alerts" on page 48
.
54 2131352
Rev 1.0 Apr.10
Using Your Device
Wi-Fi Users Information and Settings
The Wi-Fi users icon shows how many Wi-Fi users are connected to the device.
Icon Description
No Wi-Fi users are connected. (One user is connected via USB).
One user is connected via Wi-Fi.
The number indicates how many Wi-Fi users are connected.
Click the icon to display the Connected Users window.
Connected User Information
When you're logged in, the Connected Users window shows a table with information on computers currently connected to the device.
A row may optionally show one or both of these icons:
• — The user of this computer is logged in as administrator.
• — This computer is connected to the device through the USB cable.
MAC Address — Each wireless device has a unique MAC address (assigned by its manufacturer). On a Windows PC, the MAC address is called the "physical address"; on a Mac, it is called the "Ethernet ID". See
"Finding the MAC Address" on page 114
.
Block — Used to block the computer's access to the device. You might want to do this if:
• You don't recognize a listed computer.
• You have lots of data to transfer (you want to be the sole user of the bandwidth).
• You're approaching the data limit on your account.
Note: You cannot block the administrator. (The row for the administrator has the icon).
Max Wi-Fi users — Limits the number of Wi-Fi users that can connect to the device. A smaller number improves performance and security.
Disable Wi-Fi when connected via USB — Turns off the Wi-Fi of the device when connected to a computer through the USB cable. Only this computer will be able to use the device.
Battery Information and Settings
The battery icon indicates the state of the battery of the device.
The text next to the icon displays additional information, for example, the charging status (% remaining or % complete).
55
Clear Spot 4G+ User Guide
Tip: You can also check the battery icon from the Home page, Mini Window, and Device
LCD.
Icon
...
Description
Battery level is critical. Charge the device immediately. See
No battery; connected to an electrical outlet (through the power adapter).
Connected to USB. Battery is either charging, or is not inserted.
Charging through the power adapter.
Battery is low. Charge the device. See "Charging the Device" on page 31.
The more bars are shown, the more the battery is charged.
Battery is charged.
Click the icon to display the Battery Information and Settings window.
When you're logged in, you can set the behavior for when the device is:
• Battery or USB powered . Choose one of the following:
· Better battery life — At the cost of shorter Wi-Fi range.
· Longer Wi-Fi range — At the cost of shorter battery life.
• AC powered . Choose one of the following:
· Longer Wi-Fi range
· Shorter Wi-Fi range — You have a designated wireless area and you need to minimize the effect of your network on other networks in the vicinity.
Standby (Low Power) Mode
When the device is in standby (low power) mode, the 3G/4G modem radios, the
Wi-Fi radio, and the LCD are off, and the power button is flashing.
When you're logged in, you can set how soon the device goes into standby mode when no Wi-Fi users are connected to it ( Standby Timer ).
You can specify settings for battery power and AC power.
Note: This setting has no effect when the device is connected to a computer through the
USB cable.
To exit standby mode:
• Connect the device to the power adapter or computer, through the USB cable.
— or —
Press the power button .
56 2131352
Rev 1.0 Apr.10
Using Your Device
Internet Connection Information
Note: Data usage amounts are approximate and should not be used for billing purposes.
For accurate data usage amounts, check with CLEAR.
Click the data icon
The window displays:
to display the Internet Connection Information window.
• Data statistics for the current connection session:
· Data sent
· Data received
· Total transferred
· Session duration
• The WWAN IP address of the device — the external IP address of the modem (3G or 4G) — that is, the IP address of the modem as seen from the
Internet.
Viewing and Configuring Detailed Internet Connection Information
When you're logged in, the Internet Connection Information window displays a table showing data use:
• In the currently billing cycle. These numbers get automatically reset to 0 on the day selected in the Starts on day list.
• Over the lifetime of the device.
• By network (3G/4G), and by sent/received/total.
From this window you can:
• Reset the data usage figures for the current billing cycle. (Click Reset .)
• Change the start day of the billing cycle (in the Starts on day list).
microSD Card Information and Settings
The text next to the icon indicates whether the card is:
• Enabled
• Detected
• Accessible by all ("shared") or only the administrator
• Accessible with or without a password (security)
Click the icon to display the SD Card Information and Settings window. The window displays:
• The card status (see the above list)
• Storage capacity of the card, and space available
When you're logged in, you can:
• Enable or disable the microSD card slot. See
.
•
Set up access to the card. See "Setting Up Access to the microSD Card" on page 61
.
57
Clear Spot 4G+ User Guide
Sounds Information and Settings
The sounds icon ( ) shows whether the device speaker is on.
Icon Description
The device speaker is on.
The device speaker is off.
Click the icon to display the Sounds window. The window displays:
• Status of the device speaker (on or off).
• If you're logged in: check boxes to enable or disable sounds for the following events:
· Internet connected
· Internet disconnected
· Low battery — Useful as a reminder to charge the device.
· System alerts — When you hear the device beep, you can then use the device LCD or the Alerts window to get information about the alert. See
"Alert Information" on page 54 .
Note: System alerts include several types of events, for example:
• Critical battery
• Critical temperature
• Software update available
• Network update available
• Routing hardware settings reset
• Device startup failure
· Wi-Fi user has joined — Useful, for example, to detect an unwelcome Wi-Fi user if you're the only one using the device.
· Wi-Fi user has left
· Last user has left — When you hear the device beep, you can turn off the device, if nobody will be using it for awhile.
Tip:
You can also disable all sounds through the mute switch on the device. See "Mute
If you've enabled the sounds through the home page, but there are no sounds when an event occurs, check the position of the Mute switch.
58 2131352
Rev 1.0 Apr.10
Using Your Device
Home Page Buttons
Buttons Along the Top of the Home Page
The top horizontal part of the home page has the following areas and buttons:
• Admin Login
. See "Logging On as an Administrator" on page 46 .
• Admin Setup — Rerun the device setup, for example, after you've reset the software to default settings. See
"Welcome to Your Device Window - Select an Option" on page 108 .
• Advanced settings
. See "Advanced Settings" on page 59 .
• Support
. See "Support Button" on page 59 .
• Feedback
— Send your comments on the device. See "Feedback" on page 60 .
• Help — Open the Help system, display the important information booklet, or download the user guide.
Admin Setup Button
This button displays a window where you can change the administrator password,
Wi-Fi network name (SSID), Wi-Fi security type, and Wi-Fi password.
For more information, see "Welcome to Your Device Window - Select an Option" on page 108
.
Advanced Settings
From the Advanced Settings window you can configure all the settings of the device and the browser interface.
The Advanced Settings window has the following tabs; each tab has several panels.
• Device tab. See
.
• WAN tab. See
.
• Wi-Fi tab. See
• Router tab. See
"Configuring the Router Tab" on page 93 .
For help on a tab, click Help ( ). For most fields and buttons, contextual (fieldlevel) Help appears to the right of the window, when you move the cursor over the item. For more information, see
"Contextual Help in the Advanced Settings
Accessing the Advanced Settings Window
1.
Ensure you're logged in to the home page.
2.
Click Advanced settings ( ).
Support Button
The Support button opens, in a new Web browser window (or tab), the online support site for your device.
Note: This button is available only when you're connected to the Internet.
59
Clear Spot 4G+ User Guide
Feedback
The Feedback button opens, in a new Web browser window (or tab), the online feedback site for your device.
Note: This button is available only when you're connected to the Internet.
Help Button
This button displays a menu with options to:
• Display the online Help.
• Download the user guide.
• View the important information booklet. This booklet contains warranty and other information.
Buttons Below the Virtual Device
Note: The buttons appear only when you're logged in.
Connect/Disconnect Button
This button disconnects a connection, or connects (if currently there's no connection).
Power Off Button
This button turns the device off.
Note: You can turn the device on by using the device power button.
Using the microSD Card
Before Using the microSD Card Slot
1.
Enable the slot. See
"Enabling the microSD Card Slot" on page 61
.
2.
Set up access to the slot. See
"Setting Up Access to the microSD Card" on page 61
.
3.
[OPTIONAL]: Rename the microSD Shared Folder Name
4.
Inform others how they can access the card. See
.
60 2131352
Rev 1.0 Apr.10
Using Your Device
Enabling the microSD Card Slot
Before computers can recognize the microSD card, you must enable the microSD slot on the device.
1.
Ensure you're logged in to the home page.
2.
In the SD Card Information and Settings window, select Enable SD Card . (See
"microSD Card Information and Settings" on page 57 .)
— or —
From Advanced settings > Device > microSD card , in the SD-Card Slot section select Enable .
Setting Up Access to the microSD Card
If you've enabled access to the microSD card, you must also specify whether a username and password are required to access the card.
1.
Ensure you're logged in to the home page.
2.
In the SD Card Information and Settings window or from Advanced settings
> Device > microSD card , under Username and Password Security , select one of the values:
· To have no security, select None .
Anyone can use the card; no username or password is required.
· To allow only the administrator to use the card, select Administrator Only .
When prompted for the username (when you try to use the card), enter
"admin". For the password, enter the home page login password.
· To allow non-administrators to use the card, select Administrator + Guest .
3.
If you've selected Administrator + Guest : a.
[OPTIONAL]: Change the Set Guest Username and Set Guest Password fields (up to 20 characters each; spaces are allowed).
b. Give the guest username and password to people whom you want to allow access to the card.
microSD Shared Folder Name
You can optionally change the name of the folder that the microSD card shows up as (in the file browser program); the default folder name is "shared".
1.
Ensure you're logged in to the home page.
2.
Click Advanced settings > Device > MicroSD card .
3.
In the MicroSD Shared Folder Name field, type the new name.
You can use up to 32 letters, numbers, and spaces in any combination.
For information on how this folder name is used, see "Accessing the microSD
61
Clear Spot 4G+ User Guide
Inserting a microSD Card
To insert the microSD card:
1.
Gently flip open the tab labelled "microSD" on the side of the device.
62
2.
Gently insert the microSD card (label facing up) into the slot on the side of the device, until the microSD card clicks into place.
Note: If your microSD card has not been formatted, or is in a format that your computer does not recognize, you may be prompted to format the microSD card. The formatting procedure erases all the data on the microSD card, after which the files CANNOT be retrieved. To prevent the loss of important data, please check the contents before you format the microSD card.
3.
Check the status of the microSD card. See "microSD Card Information and
Removing a microSD Card
1.
Ensure you and other users have completed any file transfers.
2.
Gently flip open the tab labelled "microSD" on the side of the device.
3.
Using your fingernail or a thin blunt object, gently press the microSD card in and then release; it should partially pop out of its slot, as shown in the drawing above.
4.
Remove the microSD card and store it in a safe place.
5.
Close the tab over the microSD slot of the device.
2131352
Rev 1.0 Apr.10
Using Your Device
Accessing the microSD Card
If the microSD slot is enabled, an inserted card appears in your file browser as a shared network drive.
The way to access the card varies, depending on your operating system.
Note: In the information that follows,
<Hostname>
is the value of the
Hostname
field (in
Advanced settings > Wi-Fi > Network
and also in
Advanced settings > Router > LAN
).
Windows
1.
In Windows Explorer or Internet Explorer, type one of the following:
· \\clearspot\
· \\<Router IP address>\ (field in Advanced settings > Router > LAN )
For example: \\192.168.0.1\
· \\<Hostname>\
For example: \\MyDeviceName\
— or —
From the Windows start menu, click start > Run , and then type one of the following:
· \\clearspot\
· \\<Hostname>\
2.
Double-click the shared folder.
Mac
1.
In Finder, select Go > Connect to Server .
2.
Type one of the following:
· smb://clearspot/
· smb://<Router IP address>/
· smb://<Hostname>/
3.
When prompted, select the shared drive as the folder to mount.
Linux
1.
Open the run menu (Alt+F2) or a file browser, and type one of the following:
· smb://clearspot/
· smb://<Router IP address>/
· smb://<Hostname>/
2.
Double-click the shared folder.
Other operating systems
Please see the user documentation for your operating system or computer.
If security has been enabled for the microSD card, you will be prompted to enter
63
Clear Spot 4G+ User Guide
Updates
Note: If a software update, 3G network update, or 3G profile update is available, the device LCD displays a message, and an alert is available from the home page. See
"Software Update Available" on page 50
and "3G Network Update Available" on page 49
.
The update may improve performance and add or modify features. The updates may include the following:
• Device firmware
• 3G network update
• The browser interface
• Help files
• Other files
You can:
• Manually check for updates. See
"Manually Checking for Updates" on page 65
.
• Set the browser interface to automatically check for updates. See the next section.
Automatically Checking for Updates
To specify how often the browser interface checks for updates:
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Basic .
).
4.
In the Check for Updates list, click an option.
Note: If
Check for Updates
is not available, your device supports the Guaranteed Update feature, which automatically checks for updates, at a pre-determined frequency. This feature requires 4G coverage.
Tip: When updates are available, an alert is shown in the browser interface. See
.
64 2131352
Rev 1.0 Apr.10
Using Your Device
Manually Checking for Updates
Note: During installation of the update:
• DO NOT turn off or unplug the device.
• Your Wi-Fi and Internet connections won’t be available.
When the installation is complete, you will need to reconnect to Wi-Fi. (See "How Do
I Connect to Wi-Fi?" on page 110
).
Checking for updates
1.
Log in to the home page.
2.
Ensure you're connected to 3G/4G.
3.
Click Advanced settings (
4.
Click Device > Basic .
).
5.
Click Check for updates now . (The message next to the button indicates whether updates are available.)
Installing the updates
If updates are available, after you've manually checked for updates:
1.
Ensure your device is connected to the power adapter or computer, through the USB cable.
Note: If you’ll be using USB for data transfer (and not just for charging the device), you must install the device driver. See
"Making a Tethered Connection" on page 43 .
2.
Click Update options .
3.
Read the information in the Software Installation Options window.
4.
To install the updates, click Download and install now .
— or —
If you are not in a strong signal area, make a note of the URL displayed in the window and click I’ll get the update later . At a later time, access the URL to
download the update to your computer, and then follow the steps in "Upgrade
Firmware From a File" on page 65
.
5.
When the installation is complete, reconnect to Wi-Fi. See
"How Do I Connect to Wi-Fi?" on page 110 .
Upgrade Firmware From a File
Use this option when you have an updated firmware file that you've, for example, downloaded from the CLEAR or Sierra Wireless website.
Note: During installation of the update:
• DO NOT turn off or unplug the device.
• Your Wi-Fi and Internet connections won’t be available.
When the installation is complete, you will need to reconnect to Wi-Fi. (See "How Do
I Connect to Wi-Fi?" on page 110
).
65
Clear Spot 4G+ User Guide
To upgrade the device firmware from a file:
1.
Log in to the home page.
2.
Ensure Disable Wi-Fi when connected via USB
is selected. See "Disabling Wi-Fi
When Connected Through USB" on page 91
.
3.
Ensure your device is connected to the power adapter or computer, through the USB cable.
4.
Click Advanced settings ( ).
5.
If you want to later confirm that the upgrade was successful, write down the current version information (shown in Device > About ):
· Software version
· Firmware version (in the 3G section)
· Firmware version (in the 4G section)
6.
Click Device > Basic .
7.
[OPTIONAL]: Save the current configuration (recommended).
a.
Click Export .
b. Save the file. Note the filename and path.
8.
Click Browse next to the Update Firmware From File field, and click the firmware file to upload to the device.
9.
Click Update .
Please wait while the upgrade occurs; this may take several minutes. The device LCD shows the upgrade status. The device will restart (possibly several times).
Once the upgrade is complete, the LCD device shows the usual icons and text
(for example, the device name).
10. Compare the current version information (in Device > About ) to the values you wrote down in step 5 to confirm that the upgrade was successful.
11. If you've saved the current configuration, reload it.
a.
Click Browse next to the Import Router Settings field, and click the file you've saved.
b. Click Import .
12. Reconnect to Wi-Fi. See
"How Do I Connect to Wi-Fi?" on page 110
.
Viewing Device Information
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > About .
).
Note: 4G information is not available if
WAN mode
is "3G only". (
WAN mode
is in
Advanced settings > WAN > Setup
.)
66 2131352
Rev 1.0 Apr.10
Using Your Device
The following information is displayed:
• Model Number
• Manufacturer
• Software Version .
Firmware version for the routing hardware component of the device.
• Activation Status .
3G activated, or not activated.
• Activation Date .
Date that the 3G modem was first activated.
• Network Operator .
The carrier that your device was activated for.
• Wi-Fi Firmware Version
• Router PRI Version .
PRI version for the routing hardware component of the device. The PRI (Product Release Instructions) is a file that contains the settings used to configure wireless products for a particular service provider, customer, or purpose.
• ESN or MEID (3G).
The ESN (Electronic Serial Number) is the unique first-generation serial number assigned to the 3G component of the device.
The MEID (Mobile Equipment Identifier) is the unique second-generation serial number assigned to the 3G component of the device.
• PRI Version .
PRI version of the 3G component of the device. The PRI (Product Release
Instructions) is a file that contains the settings used to configure wireless products for a particular service provider, customer, or purpose.
• MSID (Mobile Station ID)
The MSID is also known as IMSI (International Mobile Station Identity) — an identifier of a device on the 3G network.
• PRL Version .
The PRL (Preferred Roaming List) is an account configuration item set by your service provider. It controls the radio channels and network carrier used by the 3G modem. An updated PRL may improve your 3G network service.
• Firmware Version .
Firmware version of the 3G component of the device.
• MAC Address .
MAC address of the 4G module. Each wireless device has a unique MAC address (assigned by its manufacturer).
• Firmware Version .
Firmware version of the 4G component of the device.
The window also has buttons to:
• Save the information to a text file.
• Reset the 3G/4G configuration of the device to default settings. See
"Resetting the 3G/4G Configuration to Default Settings" on page 92 .
67
Clear Spot 4G+ User Guide
Reset Button
The reset button is inside the hole located below and to the right of the battery compartment as shown below.
Reset button
For information on using this button, see
"Restarting the Device" on page 68
and
"Resetting the Software to Default Settings (Through the Reset Button)" on page 103 .
Restarting the Device
Tip: Alternatively, you may be able to restart the device by pressing and holding the power button on the device for three to four seconds.
If the device or the home page seems to stop responding, you can reset (restart) the device:
1.
Remove the battery compartment cover.
68 2131352
Using Your Device
2.
Find the small hole below and to the right of the battery compartment. The reset button is inside this hole.
Reset button
3.
Insert a thin object (for example, the end of a paper clip) into the hole, and lightly press on the bottom of the hole for about a second).
4.
Replace the battery compartment cover.
Rev 1.0 Apr.10
69
Clear Spot 4G+ User Guide
70 2131352
5: Settings
Power Settings
Battery and USB Power Settings
You can specify the settings for battery and USB power:
• Better battery life — At the cost of a shorter Wi-Fi range.
• Longer Wi-Fi range — At the cost of a shorter battery life.
To choose an option:
1.
Ensure you're logged in to the home page.
2.
Click the battery icon
Settings window opens.
. The Battery Information and
— or —
Click Advanced settings > Wi-Fi > Network .
3.
Select an option in the Battery or USB Powered section.
AC Power Settings
You can specify the settings for AC power:
• Longer Wi-Fi range
• Shorter Wi-Fi range
To choose an option:
1.
Ensure you're logged in to the home page.
2.
Click the battery icon
Settings window opens.
. The Battery Information and
— or —
Click Advanced settings > Wi-Fi > Network .
3.
Select an option in the AC Powered section.
Configuring the LCD
Turning the LCD On or Off
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Display .
).
5
Rev 1.0 Apr.10
71
Clear Spot 4G+ User Guide
4.
Set the LCD Backlight field to On or Off . ( Off helps prolong the battery life, but you can't check the LCD for status icons and messages.)
Setting the LCD Timeout
Tip: Alternatively, you can permanently turn off the LCD, in which case it will never become lit and will not display text and icons. See
"Turning the LCD On or Off" on page 71
.
To set the amount of time, after which the LCD of the device temporarily turns off:
1.
Ensure you're logged in to the home page.
2.
Click Advanced settings > Device > Display .
3.
Ensure LCD Backlight is set to On .
4.
In the Turn Off Backlight list, click a value. (A smaller value helps prolong the battery life.)
Note: The LCD turns on if an important system event occurs.
Setting the LCD Brightness
1.
Ensure you're logged in to the home page.
2.
Click Advanced settings > Device > Display .
3.
Ensure LCD Backlight is set to On .
4.
Select a value for On Battery/USB Power . (A lower brightness prolongs the battery life.)
5.
Select a value for On AC Power .
Enabling and Disabling the LED
The power button on the device acts as an LED/status indicator, and may or
To enable or disable the lighting of the power button :
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Display .
).
4.
Set the Power Button LED field to On or Off .
72 2131352
Rev 1.0 Apr.10
Settings
Sounds
Enabling and Disabling Sounds
You can enable or disable sounds of the device through:
•
The mute switch on the device (disables all sounds). See "Mute Switch" on page 36.
•
and "Enabling and Disabling Sounds for Specific
Enabling and Disabling Sounds for Specific Events
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Sounds .
).
4.
Next to each of the event types, select Enable or Disable .
Sounds for the following events can be individually enabled or disabled:
• Low Battery
Useful as a reminder to charge the device. In the Alert When list, you can select a battery level to trigger the alert.
• System Alerts
When you hear the device beep, use the device LCD or the Alerts window to get information about the alert. See
"Alert Information" on page 54
.
Note: System alerts include several types of events, for example:
• Critical battery
• Critical temperature
• Software update available
• Network update available
• Routing hardware settings reset
• Device startup failure
• Internet Connected
• Internet Disconnected
• Wi-Fi User Has Joined
Useful, for example, if you're the only one using the device, to detect an intruder.
• Wi-Fi User Has Left
• Last User Has Left
You can turn off the device if nobody will be using it for a while.
73
Clear Spot 4G+ User Guide
Low Battery Alert
You can set an alert to sound when the battery level is low.
Setting the Alert From the Home Page
1.
Ensure you're logged in to the home page.
2.
Click the Sounds icon ( ).
3.
In the Sounds window, select Low battery .
Setting the Alert From the Advanced Settings Window
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Sounds .
).
4.
For the Low Battery field, select Enable .
5.
In the Alert When list, click a battery level to trigger the alert.
Critical Battery Level Alert
You can enable an alert to sound when the battery level is critical (that is, dangerously low).
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Sounds .
).
4.
For the System Alerts field, select Enable .
Note: System alerts include several types of events, for example:
• Critical battery
• Critical temperature
• Software update available
• Network update available
• Routing hardware settings reset
• Device startup failure
74 2131352
Rev 1.0 Apr.10
Settings
Login Settings
Changing the Administrator Password
Note: If you forget the Admin login password, you’ll need to reset the device to its default settings and go through the device setup. See
"What Do I Do if I Forgot the Administrator Password?" on page 111 .
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Basic .
).
4.
In the Admin Password field, type the new password (1–20 characters/ numbers).
Automatic Login ("Remember Me")
If you enable automatic login:
• Anyone who uses the computer will automatically be logged in to the home page (as long as no one else has already logged in from another computer); entering the administrator password is not required.
• The timeout security feature is disabled — you will never be automatically logged off.
To enable automatic login:
1.
From the computer that you want to enable automatic login, log in to the home page.
2.
In the login area, select the Remember me check box.
You can repeat the above steps on other computers; however, since only one administrator can be logged in at a time, only the first person to display the home page will be logged in.
Viewing Computers That Are Set to Automatically Log In as Administrator
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Basic .
).
4.
Next to Remember Me Client List , click show list .
Disabling Automatic Login For a Specific Computer
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Basic .
).
4.
Next to Remember Me Client List , click show list .
75
Clear Spot 4G+ User Guide
76
5.
In the row for the computer that you want to disable automatic login, click
Remove .
Advanced Settings
From the Advanced Settings window you can configure all the settings of the device and the browser interface.
The Advanced Settings window has the following tabs; each tab has several panels.
• Device tab. See
.
•
WAN tab. See "WAN Tab" on page 80
.
• Wi-Fi tab. See
• Router tab. See
"Configuring the Router Tab" on page 93 .
For help on a tab, click Help ( ). For most fields and buttons, contextual (fieldlevel) Help appears to the right of the window, when you move the cursor over the item. For more information, see
"Contextual Help in the Advanced Settings
Accessing the Advanced Settings Window
1.
Ensure you're logged in to the home page.
2.
Click Advanced settings ( ).
Device Tab
Basic Panel
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Basic .
).
From this window, you can view and adjust settings, or perform the following actions:
• Admin Password
— Login password. See "Changing the Administrator
.
• Remember Me Client List — View a list of computers that are set to automati-
cally log in. See "Automatic Login ("Remember Me")" on page 75 .
• Help for Advanced Settings — Enable or disable contextual Help in the
Advanced Settings window. See
"Contextual Help in the Advanced Settings
• Import Router Settings — Import configuration settings. See
• Export Router Settings — Export configuration settings. See
• Update Firmware From File
. See "Upgrade Firmware From a File" on page 65
.
2131352
Rev 1.0 Apr.10
Settings
• Standby Timer on Battery or USB and On AC Power — Enable standby (low power) mode. See
"Standby (Low Power) Mode" on page 56
.
• Check for Updates automatically and Check for updates now
on page 64 and "Manually Checking for Updates" on page 65
.
• TRU-Install — Installs the necessary drivers the first time you connect the
Clear Spot 4G+ personal hotspot to your Windows or Mac computer. For
information on this feature, see "TRU-Install" on page 43.
Display Panel
From the Display panel of the Device tab, you can configure settings for the device
LCD.
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Display .
).
From this window, you can view or adjust these settings:
• Lighting of the power button on the device ( Power Button LED ). See
"Enabling and Disabling the LED" on page 72 .
• Turn the LCD on or off ( LCD Backlight ). See
"Turning the LCD On or Off" on page 71
.
• LCD timeout — how soon the LCD goes dormant (Turn Off Backlight). See
"Setting the LCD Timeout" on page 72 .
• Brightness of the LCD ( Backlight Settings ). See
"Setting the LCD Brightness" on page 72
.
microSD Card Panel
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > microSD Card .
).
From this window, you can view and adjust settings, or perform the following actions:
• Status of the microSD card slot.
•
Enable the microSD card slot. See "Enabling the microSD Card Slot" on page 61
.
•
Folder name for the shared micro SD card. See "microSD Shared Folder
.
•
Set up access to the microSD Card. See "Setting Up Access to the microSD
Sounds Panel
From the Sounds panel of the Device tab, you can enable or disable sounds for specific types of events.
1.
Log in to the home page.
77
Clear Spot 4G+ User Guide
78
2.
Click Advanced settings (
3.
Click Device > Sounds .
).
4.
Next to each of the event types, select Enable or Disable .
Sounds for the following events can be individually enabled or disabled:
• Low Battery
Useful as a reminder to charge the device. In the Alert When list, you can select a battery level to trigger the alert.
• System Alerts
When you hear the device beep, use the device LCD or the Alerts window to get information about the alert. See
"Alert Information" on page 54
.
Note: System alerts include several types of events, for example:
• Critical battery
• Critical temperature
• Software update available
• Network update available
• Routing hardware settings reset
• Device startup failure
• Internet Connected
• Internet Disconnected
• Wi-Fi User Has Joined
Useful, for example, if you're the only one using the device, to detect an intruder.
• Wi-Fi User Has Left
• Last User Has Left
You can turn off the device if nobody will be using it for a while.
About Panel
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > About .
).
Note: 4G information is not available if WAN mode is "3G only". ( WAN mode is in
Advanced settings > WAN > Setup .)
The following information is displayed:
• Model Number
• Manufacturer
• Software Version .
Firmware version for the routing hardware component of the device.
• Activation Status .
3G activated, or not activated.
2131352
Rev 1.0 Apr.10
Settings
• Activation Date .
Date that the 3G modem was first activated.
• Network Operator .
The carrier that your device was activated for.
• Wi-Fi Firmware Version
• Router PRI Version .
PRI version for the routing hardware component of the device. The PRI (Product Release Instructions) is a file that contains the settings used to configure wireless products for a particular service provider, customer, or purpose.
• ESN or MEID (3G).
The ESN (Electronic Serial Number) is the unique first-generation serial number assigned to the 3G component of the device.
The MEID (Mobile Equipment Identifier) is the unique second-generation serial number assigned to the 3G component of the device.
• PRI Version .
PRI version of the 3G component of the device. The PRI (Product Release
Instructions) is a file that contains the settings used to configure wireless products for a particular service provider, customer, or purpose.
• MSID (Mobile Station ID)
The MSID is also known as IMSI (International Mobile Station Identity) — an identifier of a device on the 3G network.
• PRL Version .
The PRL (Preferred Roaming List) is an account configuration item set by your service provider. It controls the radio channels and network carrier used by the 3G modem. An updated PRL may improve your 3G network service.
• Firmware Version .
Firmware version of the 3G component of the device.
• MAC Address .
MAC address of the 4G module. Each wireless device has a unique MAC address (assigned by its manufacturer).
• Firmware Version .
Firmware version of the 4G component of the device.
The window also has buttons to:
• Save the information to a text file.
• Reset the 3G/4G configuration of the device to default settings. See
"Resetting the 3G/4G Configuration to Default Settings" on page 92 .
79
Clear Spot 4G+ User Guide
Log Panel
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Log .
).
From this window, you can:
• Enable logging of system events. See
"Enabling and Disabling Logging of
.
• Enable logging of connects/disconnects. See
Logging of Connect/Disconnects" on page 106 .
• Export logs. See
"Exporting System Events" on page 107
and
Connection History" on page 106 .
•
Clear logs. See "Clearing the System Events Log" on page 107
and
"Clearing the Connection History" on page 106 .
•
Set the method used for time acquisition. See "Setting the Method Used for
Time Acquisition" on page 107 .
WAN Tab
See also "3G Panel" on page 92
.
Setup Panel
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click WAN > Setup .
).
From this window, you can view and adjust settings, or perform the following actions:
• Active Network — Network that is currently being used for your data connection: 3G, 4G, or none.
• Network Operator.
The carrier that your device was activated for.
• Session Duration — How long you've been connected to the network.
• Session Total Data — Amount of data transferred over the lifetime of the device
(by network type) and in the current session.
• WAN Mode — Network(s) to connect to, and in what order.
· 4G Preferred — Connection can be established to either 3G or 4G; if both are available, 4G is used. This setting is recommended if your service provider has no data limit for 4G, but does for 3G, or you want to take advantage of the faster data transfer speeds of 4G.
· 4G Only — Connection can be established only to 4G.
· 3G Only — Connection can be established only to 3G.
If you don’t have 4G coverage, you can save power by selecting "3G Only".
80 2131352
Rev 1.0 Apr.10
Settings
• Connect Automatically to the network when the Clear Spot 4G+ personal hotspot powers on.
• Failover wait time — How long the device should wait, after it loses the connection with the preferred network, before it attempts to connect to the other network (not available if WAN mode is "3G only" or "4G only").
• Switchback wait time — How long the device should wait, when the lesspreferred network is connected and the preferred network becomes available, before switching to the preferred network (not available if WAN mode is
"3G only" or "4G only").
• Update 3G PRL — Check whether an updated PRL is available.
The PRL (Preferred Roaming List) is an account configuration item set by your service provider. It controls the radio channels and network carrier used by the 3G modem. An updated PRL may improve your 3G network service.
Note: A 3G connection to the Internet won’t be available until the update is complete. (The
4G connection won’t be affected).
• Update 3G Profile — Check whether an updated profile for your 3G connection is available.
An updated profile may improve your 3G network service.
4G Panel
To access this panel:
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click WAN > 4G .
).
Note: 4G information is not available if
WAN mode
is "3G only". (
WAN mode
is in
Advanced settings > WAN > Setup
.)
From this window, you can view this 4G information:
• Connection Status — connected, or not connected.
• Coverage Type — 4G, 4G Off, or no service.
• RSSI and CINR .
RSSI reflects the signal strength of the network.
CINR stands for Carrier to Interference-plus-Noise Ratio, and is a measurement of signal effectiveness. For the receiver to decode the carrier signal, the latter must be in an acceptable CINR range.
• Tx Power — Transmitter power. A higher number is better.
• Center Frequency — Frequency of the 4G channel used for the data connection.
• NSP-ID — ID of the 4G Network Service Provider.
• NAP-ID — ID of the 4G Network Access Provider.
• BSID — Base Station ID.
81
Clear Spot 4G+ User Guide
82
• Preable — Preamble ID of the current base station that the modem is listening to.
• Realm — Login address used for 4G service (user@realm).
• Certificate information
Wi-Fi Tab
Network Panel
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Wi-Fi > Network .
).
From this window, you can view and adjust settings, or perform the following actions:
• Disable Wi-Fi upon USB-PC — Only a computer that is connected to the device
through the USB cable can use the device. See "Disabling Wi-Fi When
Connected Through USB" on page 91
.
• SSID — Wi-Fi network name; identifies your Wi-Fi network and is visible to other Wi-Fi-enabled devices. See
"SSID (Wi-Fi Network Name)" on page 84
.
• Hostname — Device name. See
"Host Name (Device Name)" on page 90
and
"Displaying the Home Page of the Device" on page 46.
• Link SSID and Hostname
. See "Linking the SSID and the Host Name" on page 85
.
If you link the SSID (Wi-Fi network name) and the Hostname (name of your device):
• The SSID becomes whatever the Hostname is (you cannot change the SSID
— only the Hostname).
• You only need to remember one name when selecting the Wi-Fi network, accessing the browser interface, or accessing the microSD card.
• SSID Broadcast .
If broadcast is enabled, the wireless network is displayed in the list of Wi-Fi networks available in the local area. For increased security, set this field to
Disable . You will need to give the SSID to the people who will be accessing your network.
• Max Number of Users
Limits the number of Wi-Fi users that can connect to the device. A smaller number improves performance and security.
• Battery or USB Powered (power settings)
· Better battery life — At the cost of a shorter Wi-Fi range.
· Longer Wi-Fi range — At the cost of a shorter battery life.
• AC Powered (power settings)
· Longer Wi-Fi range
· Shorter Wi-Fi range
• Wi-Fi Channel
The Wi-Fi channel is the active channel of the Wi-Fi access point. If your network is having performance issues (possibly caused by other Wi-Fi networks in the vicinity using the same channel), try a different Wi-Fi channel.
2131352
Rev 1.0 Apr.10
Settings
• Basic Rate — Type of wireless devices connected to your network.
If you're certain that all of the Wi-Fi devices used with your device support
802.11g, then select 802.11g only (this ensures faster Wi-Fi speeds); otherwise, select 802.11b/g compatibility .
• RTS Threshold
Specifies the smallest packet size, in bytes, for which RTS/CTS (Request to
Send/Clear to Send) handshaking is used. The recommended value is 2347.
Change this value only if you're experiencing inconsistent data flow. Make only minor changes to this value.
• Fragmentation Threshold
Specifies the largest allowable size, in bytes, for a packet. If the packet is larger than this, it is fragmented into multiple packet before it is transmitted. To prevent poor network performance, it's recommended to keep this value as large as possible (up to 2346).
• List of connected devices — Display a window that shows connected computers.
A row may optionally show one or both of these icons:
• — The user of this computer is logged in as administrator.
• — This computer is connected to the device through the USB cable.
Security Panel
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Wi-Fi > Security .
).
From this window, you can set the:
•
Wi-Fi security type. See "Wi-Fi Security" on page 86 .
• Wi-Fi password. See
.
•
Wi-Fi Password Reminder feature. See "Wi-Fi Password Reminder" on page 88
.
MAC Filter Panel
The MAC (Media Access Control) filter is used to grant ("whitelist") or block
("blacklist") wireless devices access to the Wi-Fi, 3G, and 4G networks. Access is based on the MAC address of each wireless device.
MAC filtering can prevent unauthorized wireless devices from connecting to your network.
MAC filtering increases security of your network. You can give access to your network, based on the MAC address of the wireless devices. This makes it harder for a hacker to use a MAC address to access your network.
To access this panel:
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Wi-Fi > MAC Filter .
).
83
Clear Spot 4G+ User Guide
From this window, you can:
• Display a list of computers that are:
· Allowed to access the network ( MAC Filter Mode = "Allow all in list")
· Not allowed to access the network ( MAC Filter Mode = "Block all in list")
• Add or remove a computer from the lists. See
Can Access the Network" on page 88
and "Specifying Computers That Are
Not Allowed to Access the Network" on page 89 .
• Display a list of computers that are currently connected through Wi-Fi. See
"Displaying a List of Currently Connected Computers" on page 90
.
Configuring the Wi-Fi Network
You can configure basic settings of the Wi-Fi network through the setup pages.
1.
Ensure you're logged in to the home page.
2.
Click Admin setup ( ).
For more information, see "Changing the Password and Settings" on page 38.
You can configure basic and advanced settings of the Wi-Fi network through the
Advanced settings window.
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Wi-Fi > Network .
).
For more information, see "Network Panel" on page 82
.
See also:
•
"Disabling Wi-Fi When Connected Through USB" on page 91
.
•
"Battery and USB Power Settings" on page 71 .
•
"AC Power Settings" on page 71
SSID (Wi-Fi Network Name)
The SSID identifies your Wi-Fi network and is visible to other Wi-Fi-enabled devices.
It appears on your device’s LCD screen; if more than one Clear Spot 4G+ personal hotspot is available, you can use this name to tell the devices apart.
You can display the home page by typing the SSID in your Web browser (if Link
SSID and Hostname
is selected; see "Linking the SSID and the Host Name" on page 85
).
You should make the SSID unique and change it on a regular basis for optimal security.
84 2131352
Rev 1.0 Apr.10
Settings
To change the SSID:
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Wi-Fi > Network .
).
4.
In the SSID field, enter the new name.
If the SSID field is not available, Link SSID and Hostname is enabled. You must either edit Hostname (and the SSID will get the same value), or disable
Link SSID and Hostname and edit the SSID.
5.
Click Save .
6.
Reconnect to Wi-Fi: follow the instructions on-screen, and see "How Do
I Connect to Wi-Fi?" on page 110
.
Note: If you're sharing your connection with others, they also must reconnect to Wi-Fi; provide them the new SSID.
For security reasons, it's recommended you disable SSID Broadcast. See "Network
.
Linking the SSID and the Host Name
If you link the SSID (Wi-Fi network name) and the Hostname (name of your device):
• The SSID becomes whatever the Hostname is (you cannot change the SSID
— only the Hostname).
• You only need to remember one name when selecting the Wi-Fi network, accessing the browser interface, or accessing the microSD card.
To link the SSID and the Hostname:
1.
Log in to the home page.
2.
Click Advanced settings ( ).
3.
Click Wi-Fi > Network or Router > LAN .
4.
Select the Link SSID and Hostname check box.
The SSID field gets the value of Hostname and becomes unavailable (grayed out).
5.
Click Save .
The device resets, after which you must reconnect to Wi-Fi. See "How Do
I Connect to Wi-Fi?" on page 110
.
85
Clear Spot 4G+ User Guide
86
Wi-Fi Security
By default, Wi-Fi security is enabled for your device and the Wi-Fi network.
Note: All the devices used with the Clear Spot 4G+ personal hotspot must support the selected security type.
To change the security used by Wi-Fi:
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Wi-Fi > Security .
).
4.
Select one of the options:
• None
No security (no password is required to access the Wi-Fi network); not recommended. Anyone may access your device and use your Internet connection
(you are responsible for payment for data usage).
• WEP-64 Bit - Shared
Lower security. Works with older and newer Wi-Fi devices. Recommended only if any of your devices don't support WPA or WPA2.
Shared WEP uses the same key for encryption and authentication; some consider shared WEP to be less secure than open WEP.
• WEP-128 Bit - Shared
Lower security. Works with older and newer Wi-Fi devices. Recommended only if any of your devices don't support WPA or WPA2.
Shared WEP uses the same key for encryption and authentication; some consider shared WEP to be less secure than open WEP.
• WEP-64 Bit - Open
Lower security. Works with older and newer Wi-Fi devices. Recommended only if any of your devices don't support WPA or WPA2.
Open WEP uses the key for encryption, but not for authentication.
• WEP-128 Bit - Open
Lower security. Works with older and newer Wi-Fi devices. Recommended only if any of your devices don't support WPA or WPA2.
Open WEP uses the key for encryption, but not for authentication.
• WPA-Personal - TKIP
A strong security standard, supported by most Wi-Fi devices.
• WPA-Personal - TKIP/AES
A strong security standard, supported by most Wi-Fi devices.
• WPA2-Personal - AES
A stronger, newer security standard. Limited to newer Wi-Fi devices.
• WPA2-Personal - TKIP/AES
A stronger, newer security standard. Limited to newer Wi-Fi devices.
• WPA/WPA2 Personal (recommended setting)
Wi-Fi devices that use either WPA or WPA2 can connect to the device. Supported by most Wi-Fi devices.
2131352
Rev 1.0 Apr.10
Settings
5.
Click Save .
The option you select determines the Wi-Fi security used and also the maximum length of the Wi-Fi password.
Wi-Fi Password
If Wi-Fi security is enabled, a Wi-Fi password is required to connect to the Wi-Fi network.
Some general rules to make your password more secure:
• Use letters and numbers
• Use special characters (for example, @)
• Use both uppercase and lowercase letters
To change the Wi-Fi password:
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Wi-Fi > Security .
).
4.
In the Wi-Fi Password field, type the password; the maximum length depends on the Wi-Fi security type that you've selected.
• None
No security (no password is required to access the Wi-Fi network); not recommended. Anyone may access your device and use your Internet connection
(you are responsible for payment for data usage).
• WEP-64 bit - Shared
5 ASCII characters.
• WEP-128 bit - Shared
13 ASCII characters.
• WEP-64 bit - Open
5 ASCII characters.
• WEP-128 bit - Open
13 ASCII characters.
• WPA-Personal - TKIP
ASCII string, 8 to 63 characters.
• WPA-Personal - TKIP/AES
ASCII string, 8 to 63 characters.
• WPA2-Personal - AES
ASCII string, 8 to 63 characters.
• WPA2-Personal - TKIP/AES
ASCII string, 8 to 63 characters.
• WPA/WPA2 Personal
ASCII string, 8 to 63 characters.
5.
Click Save .
87
Clear Spot 4G+ User Guide
88
Wi-Fi Password Reminder
When the Wi-Fi Password Reminder feature is enabled, you can display the Wi-Fi password on the LCD of the device:
1.
If the LCD is dark (no text or icons are displayed): a.
Ensure the LCD is enabled. See
"Turning the LCD On or Off" on page 71 .
b. Briefly press the power button on the device.
2.
Press the power button on the device twice, quickly (within 0.5 seconds).
The information is displayed for approximately 20 seconds. To clear the information before that, briefly press the power button on the device.
Enabling the Wi-Fi Password Reminder
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Wi-Fi > Security .
).
4.
In the Password Reminder section, select On .
5.
Click Save .
Allowing or Denying Computers Access to the Network
The MAC (Media Access Control) filter is used to grant ("whitelist") or block
("blacklist") wireless devices access to the Wi-Fi, 3G, and 4G networks. Access is based on the MAC address of each wireless device.
MAC filtering can prevent unauthorized wireless devices from connecting to your network.
You can choose one of three modes:
• No filtering — All computers are allowed to access the network.
• Allow all in list — Only computers that are in this list are allowed to access the network.
• Block all in list — All computers are allowed to access the network, unless they're in this list.
In any case, a user still needs to provide the correct Wi-Fi password to access the network.
Specifying Computers That Can Access the Network
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Wi-Fi > MAC Filter .
).
4.
In the MAC Filter Mode list, click Allow all in list .
5.
Do one of the following:
• If the computer you want to allow access is currently connected to the Clear
Spot 4G+ personal hotspot, click List of connected devices .
In the row for the computer, click Add .
2131352
Rev 1.0 Apr.10
Settings
• Click Add .
In the MAC Address field, enter the MAC address of the computer you're
adding to the list. (If you don't know this address, see "Finding the MAC
In the Name field, enter a name, for example "Amy's PC".
6.
Repeat step 5 for each computer you want to allow access.
Specifying Computers That Are Not Allowed to Access the Network
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Wi-Fi > MAC Filter .
).
4.
In the MAC Filter Mode list, click Block all in list .
5.
Determine and block an undesired user of your network.
a.
Click the List of connected devices link.
b. If you see a device you don't recognize, you can compare its MAC address to the MAC address of each of the devices on your network.
To determine the MAC address of each device you have, see "Finding the
MAC Address" on page 114 . If none of your devices have this MAC
address, that device might be an intruder.
c.
In the row for the device you want to block, click Add .
6.
For each computer you want to block, repeat step 5.
Tip: The Connected Users window has a
Block
check box, available for each currently connected user (except the administrator [
]). See "Wi-Fi Users Information and
Removing a Computer From the Allowed or Disallowed Lists
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Wi-Fi > MAC Filter .
).
4.
In the MAC filter mode list, click either Allow all in list or Block all in list .
5.
Click the row that you want to remove.
A row of buttons ( Delete , OK , Cancel ) appears.
6.
Click Delete .
89
Clear Spot 4G+ User Guide
Displaying a List of Currently Connected Computers
1.
Ensure you're logged in to the home page.
2.
Click the icon to display the Connected Users window.
— or —
Click Advanced settings > Wi-Fi > Mac Filter , and click List of connected devices .
A row displays the icon if the user is logged in as administrator.
Host Name (Device Name)
The host name is, in essence, a name you're giving the device.
The host name is shown on your device’s LCD screen; if more than one device is available, you can use this name to tell the devices apart. See
"Linking the SSID and the Host Name" on page 85 .
This name is also used when you type a command to access the:
• Home page. See
"Displaying the Home Page of the Device" on page 46.
• microSD card. See
"Accessing the microSD Card" on page 63
.
To change the host name:
1.
Log in to the home page.
2.
Click Advanced settings ( ).
3.
Click Wi-Fi > Network or Router > LAN .
4.
In the Hostname field, enter a name for your device.
Input rules:
1-15 ASCII characters. Valid characters are:
· a-z
· A-Z
· 0-9. Note that the host name cannot be all numbers.
· - (hyphen). Note that the host name cannot start or end with a hyphen.
Setting the Maximum Number of Wi-Fi Users
If your network is having performance issues, you might want to decrease the number of Wi-Fi users allowed to connect to the device.
1.
Ensure you're logged in to the home page.
2.
Click the icon and, in the Connected Users window, click a value in the
Max Wi-Fi users list.
— or —
Click Advanced settings > Wi-Fi > Network , and click a value in the Max Number of
Users list.
90 2131352
Rev 1.0 Apr.10
Settings
Wi-Fi Channel
The Wi-Fi channel is the active channel of the Wi-Fi access point. If your network is having performance issues (possibly caused by other Wi-Fi networks in the vicinity using the same channel), try a different Wi-Fi channel.
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Wi-Fi > Network .
).
4.
Click a channel in the Wi-Fi Channel list, or, to have the device automatically determine the channel to use, click Auto .
Disabling Wi-Fi When Connected Through USB
You can optionally turn off the device's Wi-Fi when connected via the USB cable.
In this case:
• Only a computer that is connected to the device through the USB cable can use the device.
• You can prolong the battery life of the device.
• The battery charges faster.
To enable this feature:
1.
Ensure you're logged in to the home page.
2.
Click the Connected Users icon (for example, ) and select Disable Wi-Fi when connected via USB .
— or —
Click Advanced settings > Wi-Fi > Network and set Disable Wi-Fi upon USB-PC to
On .
Configuring 3G/4G
Viewing 3G Activation Information
1.
Log in to the home page.
2.
Click Advanced settings (
3.
CLick Device > About .
).
The following fields are related to 3G activation:
• Activation Status
Activated, or not activated.
• Activation Date
Date that the 3G modem was first activated.
• Network Operator
The carrier that your device was activated for.
91
Clear Spot 4G+ User Guide
3G Panel
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click WAN > 3G .
).
From this window, you can view or update this information, or perform these actions:
• Connection Status : connected, not connected, or dormant.
Dormant means a connection is established, but no data is being transferred.
• Service Type used for the data connection (1xRTT, EVDO, or EVDO Rev. A).
• Coverage Type available, and RSSI and Ec/Io for each type.
RSSI reflects the signal strength of the network.
Ec/Io is a dimensionless ratio of the average power of a channel, typically the pilot channel, to the total signal power.
• MDN (Mobile Directory Number) — a 10-digit phone number.
• SID (System ID)
The System ID identifies your home network area.
• MSID (Mobile Station ID)
The MSID is also known as IMSI (International Mobile Station Identity) — an identifier of a device on the 3G network.
• NAI (Network Access Identifier)
The NAI is a user ID for accessing the 3G network.
• PRL Version
The PRL (Preferred Roaming List) is an account configuration item set by your service provider. It controls the radio channels and network carrier used by the 3G modem. An updated PRL may improve your 3G network service.
• Load 3G PRL — For example, you've received via email or downloaded a file).
Alternatively, you can check online for a PRL update — in Advanced settings
> WAN > Setup , click Update 3G PRL .
Resetting the 3G/4G Configuration to Default Settings
Note: Reset the configuration only if instructed by a CLEAR representative.
After a configuration reset:
• You must go through the device setup (
page 37 ) and 3G activation (the latter starts
automatically).
• Any changes you've made to the settings are lost.
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > About .
).
4.
Click Reset Device to Factory Defaults .
92 2131352
Rev 1.0 Apr.10
Settings
5.
When prompted, enter the SPC (Service Programming Code). (If you don't know your SPC, contact CLEAR.)
You won't be able to establish a data connection until you:
1.
Go through the device setup ( page 37
).
2.
Go through 3G activation or, if using 4G, use pay-as-you-go.
Configuring the Router Tab
You can configure the routing hardware component of the device through the
Advanced Settings window.
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Router .
).
4.
Depending on the settings you want to configure, click one of the panels:
• Basic
. See "Basic Panel" on page 93 .
• LAN
.
• Port Forward
. See "Port Forward Panel" on page 98 .
• Port Trigger . See
"Port Trigger Panel" on page 100
.
• DMZ
. See "DMZ Panel" on page 102 .
Basic Panel
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Router > Basic .
).
From this window, you can enable or disable these features, or perform these actions:
• Port forwarding . See
"Port Forward Panel" on page 98
.
• Port triggering
. See "Port Trigger Panel" on page 100 .
• DMZ
. See "DMZ Panel" on page 102 .
• UPnP
(universal plug and play). See "UPnP (Universal Plug and Play)" on page 94
.
• SPI (stateful packet inspection). See
"SPI (Stateful Packet Inspection)" on page 94
.
• Router Settings Reset
93
Clear Spot 4G+ User Guide
94
UPnP (Universal Plug and Play)
UPnP provides simple and robust connectivity among consumer electronics, intelligent appliances, and mobile devices from many different vendors. For more information, see www.upnp.org
.
Note: If UPnP is enabled, there are potential security risks.
Enabling UPnP
Before you can use UpnP, you must enable it.
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Router > Basic .
4.
Next to UPnP , select Enable .
).
SPI (Stateful Packet Inspection)
SPI, also known as "dynamic packet filtering," helps to prevent cyberattacks by validating that the traffic passing through a session conforms to the protocol used for this type of session. Packets that are not conforming get rejected.
Enabling SPI
Before you can use SPI, you must enable it.
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Router > Basic .
4.
Next to SPI , select Enable .
).
LAN Panel
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Router > LAN .
).
From this window, you can view and adjust settings, or perform the following actions:
• Router IP Address (on the LAN).
• Subnet Mask
The routing hardware's internal LAN subnet mask.
• Hostname (Device name). See
"Host Name (Device Name)" on page 90
and
"Displaying the Home Page of the Device" on page 46.
• SSID
(Wi-Fi network name). See "SSID (Wi-Fi Network Name)" on page 84 .
• Link SSID and Hostname
. See "Linking the SSID and the Host Name" on page 85
.
2131352
Rev 1.0 Apr.10
Settings
• DHCP Server (enable DHCP)
Note: The following items are displayed only when DHCP is enabled.
• DHCP IP Address Range
The starting and ending address of the range of IP addresses available for the device to dynamically (that is, not permanently) assign to computers connected to it.
• DHCP Lease Time
Amount of time, in minutes, a computer can use its assigned IP address before it is required to renew the lease. After this time is up, the computer is automatically assigned a new dynamic IP address.
Enter a number between 2 and 10080.
• Max DHCP Clients
The number of DHCP addresses that can be assigned and active at one time.
It's recommended you set this to a number greater than the number of Wi-Fi users.
• DNS Mode
The DNS Mode setting specifies how the DNS servers (that the DHCP clients are to communicate with) are obtained.
· Auto : Use the DNS server specified by CLEAR. DNS Relay is enabled by default.
· Manual : The routing hardware assigns DHCP clients the DNS servers specified in the Manual DNS Server #1 and #2 fields.
Use this option to access a DNS server that provides customized addressing or if you have a local DNS server on your network.
If DNS Relay is disabled, the routing hardware rejects DNS requests targeting the internal DNS proxy.
• Manual DNS Server #1 and #2 — Static IP addresses to use for the DNS servers (if DNS Mode is Manual).
Available only if DNS Mode is Manual.
• DNS Relay
If enabled, and if DNS Mode (see above) is Manual, the routing hardware assigns DHCP clients the DNS servers specified in the Manual DNS Server #1 and #2 fields.
If disabled, the routing hardware rejects DNS requests targeting the internal
DNS proxy.
The DNS Relay field is configurable and displayed only if DNS Mode is Manual.
If DNS Mode is Auto, DNS Relay is enabled by default.
• DHCP Static IP Assigment List — Assign a permanent IP address to a MAC address, and view the static IP assignment list. See
.
95
Clear Spot 4G+ User Guide
DHCP
DHCP (Dynamic Host Control Protocol) automatically assigns an IP address to each device on the network and manages other network configuration information for devices connected to your network. You do not need to manually configure the
IP address on each device that's on your network.
The assigned IP addresses are not permanent (as opposed to when using static
IP).
Most ISPs (Internet Service Providers) use DHCP.
Normally, you should enable DHCP, in which case you must configure each device on the network with one of the following:
• TCP/IP settings set to "Obtain an IP address automatically"
• TCP/IP bound to the Ethernet connection with DHCP
If DHCP is disabled, you must configure each device on the network with:
• Fixed (permanent/static) IP address.
• DNS server addresses (provided by CLEAR).
Enabling DHCP
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Router > LAN .
).
4.
Next to DHCP Server , select Enable .
Configuring DHCP
To configure DHCP settings, DHCP must be enabled ( Advanced settings > Router
> LAN > DHCP Server ).
You can set the following DHCP settings in Advanced settings > Router > LAN :
• DHCP IP Address Range
The starting and ending address of the range of IP addresses available for the device to dynamically (that is, not permanently) assign to computers connected to it.
The start address must be 192.168.0.10 or above.
The ending address must be 192.168.0.50 or below.
• DHCP Lease Time
Amount of time, in minutes, a computer can use its assigned IP address before it is required to renew the lease. After this time is up, the computer is automatically assigned a new dynamic IP address.
Enter a number between 2 and 10080.
• Max DHCP Clients
The number of DHCP addresses that can be assigned and active at one time.
It's recommended you set this to a number greater than the number of Wi-Fi users.
96 2131352
Rev 1.0 Apr.10
Settings
• DNS Mode
The DNS Mode setting specifies how the DNS servers (that the DHCP clients are to communicate with) are obtained. See
.
• DHCP Static Assignment List — Assign a permanent (static) IP address to a device on your network, and view the static IP assignment list. See the next section.
DHCP Static IP Assignment List
With DHCP, IP addresses are assigned dynamically; devices typically don't have a permanent IP address.
However, in some cases you might want to assign a static
(permanent) IP address to a device, while still using DHCP for the rest of the devices on your network. This is also known as "DHCP reservation". You might want to do this with, for example, a Web server, FTP server, media server.
Viewing the Static IP Assignment List
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Router > LAN .
).
4.
Ensure DHCP is enabled ( DHCP Server ).
5.
Click DHCP Static IP Assignment List .
Assigning an IP Address Based on a MAC Address
1.
Follow the above steps to display the DHCP Static IP Assignment List window.
2.
In the Hostname field, enter a meaningful description of the device.
3.
In the MAC Address field, enter the MAC Address of the device. (If you don't
know this address, see "Finding the MAC Address" on page 114 .)
4.
In the IP Address field, enter the IP address you want to assign to the device.
5.
Select the Enable check box to have the device use the designated IP address.
6.
Click Add .
7.
Click save .
Removing an IP Address Based on a MAC Address
1.
Click DHCP Static IP Assignment List on the LAN panel of the Router tab.
2.
To keep the device information in the list (in case you want to re-enable
DHCP for this MAC address later on), clear the Enable check box.
— or —
To remove the device from the list: a.
Click the row that you want to remove.
A row of buttons ( Delete , OK , Cancel ) appears.
b. Click Delete .
97
Clear Spot 4G+ User Guide
DNS Mode
The DNS Mode setting specifies how the DNS servers (that the DHCP clients are to communicate with) are obtained.
1.
Log in to the home page.
2.
Click Advanced settings ( ).
3.
Click Router > LAN .
4.
Set DNS Mode to one of the following:
• Auto : Use the DNS server specified by CLEAR. DNS Relay is enabled by default.
• Manual : The routing hardware assigns DHCP clients the DNS servers specified in the Manual DNS Server #1 and #2 fields.
Use this option to access a DNS server that provides customized addressing or if you have a local DNS server on your network.
If DNS Relay is disabled, the routing hardware rejects DNS requests targeting the internal DNS proxy.
For information on DNS Relay, see "LAN Panel" on page 94
.
Port Forward Panel
Normally, incoming traffic (from the Internet) is blocked. However, port forwarding lets you forward incoming traffic to specific ports and devices (per their local IP address) on your network. For example, you can configure port forwarding so that:
• You can access your Remote Desktop from the Internet (by specifying the
WAN [public] IP address that the device is using).
• Internet users can access a Web, FTP, or email server, or gaming or Internet application hosted by your computer.
Note: Port forwarding creates a security risk. When not required, port forwarding should be disabled.
Port forwarding does not apply to normal browsing, file downloading, running most online games or other applications hosted on the Internet. (Some online games require port forwarding.)
Before you can use or configure port forwarding, you must enable it. See
"Enabling Port Forwarding" on page 99 .
From the Port Forward panel of the Router tab of the Advanced Settings window, you can:
• Enable port forwarding for an application. See
"Enabling Port Forwarding for an Application" on page 99 .
• Remove an application from the port forwarding list. See
Forwarding for an Application" on page 99
.
98 2131352
Rev 1.0 Apr.10
Settings
Enabling Port Forwarding
Before you can use or configure Port Forwarding, you must enable it.
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Router > Basic .
).
4.
Next to Port Forwarding , select Enable .
5.
Click Save .
Enabling Port Forwarding for an Application
1.
Ensure you've enabled port forwarding. See "Enabling Port Forwarding" on page 99
.
2.
Display the "Port forward" window.
a.
Log in to the home page.
b. Click Advanced settings ( c.
Click Router > Port Forward .
).
3.
In the last row of the table, click the Application field, and select the application type from the list.
The values for Start and End ports are automatically filled in.
4.
If necessary, change the range of port numbers associated with the application. Traffic will be allowed (not blocked) if its destination port number is in the specified range.
a.
In the Start field, enter the number that starts the port range.
b. In the End field, enter the number that ends the port range.
If the range consists of only one port, enter the number that you entered in the Start field.
5.
In the Protocol list, click the protocol(s) used for this application (TCP, UDP, or both).
6.
In the IP Address field, enter the IP address of the server to be accessed.
7.
Ensure Enable is selected.
8.
Click Add .
9.
Click save .
Disabling Port Forwarding for an Application
1.
Ensure you've enabled port forwarding. See "Enabling Port Forwarding" on page 99
.
2.
Display the "Port forward" window.
a.
Log in to the home page.
b. Click Advanced settings ( c.
Click Router > Port forward .
).
99
Clear Spot 4G+ User Guide
3.
To keep the application in the list (in case you want to re-enable port forwarding later on), clear the Enable check box.
— or —
To remove the application from the list: a.
Click the row that you want to remove.
A row of buttons ( Delete , OK , Cancel ) appears.
b. Click Delete .
Port Trigger Panel
Some applications require multiple ports open for communication, many of which may be initiated by a computer on the WAN. Examples of this include video conferencing, VoIP (Internet telephony), and Internet gaming.
With port triggering, the device monitors outgoing data on specific port numbers
(trigger ports).
The device keeps track of the IP address of the computer that sends data on these trigger ports, so that when incoming data on the Forward ports arrives, the device sends the incoming data to the same computer.
Before you can use or configure port triggering, you must enable it. See
Port Triggering" on page 100 .
From the Port Trigger panel of the Router tab of the Advanced Settings window, you can:
• Enable port triggering for specified protocols and ports. See
Triggering for Specified Protocols and Ports" on page 100 .
• Remove protocols and ports from the port triggering list. See
Ports from the Port Triggering List" on page 101
.
Enabling Port Triggering
Before you can use or configure Port Triggering, you must enable it.
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Router > Basic .
).
4.
Next to Port Triggering , select Enable .
Enabling Port Triggering for Specified Protocols and Ports
1.
Ensure you've enabled port triggering. See
"Enabling Port Triggering" on page 100 .
2.
Display the "Port trigger" window.
a.
Log in to the home page.
b. Click Advanced settings ( c.
Click Router > Port Trigger .
).
100 2131352
Rev 1.0 Apr.10
Settings
3.
In the last row of the table, in the first Protocol list, click the protocol(s) used by the application for outgoing traffic (to the Internet, sent through the trigger ports).
4.
In the Trigger Ports field, enter the port number(s) used to determine that the application is in use (that is, specify the port number or range of port numbers that the application uses for outgoing traffic). (Check the user documentation for the application.)
To specify a range of port numbers, separate the start and end port number with a hyphen.
5.
In the second Protocol list, click the protocol(s) used by the application for incoming traffic (from the Internet).
6.
In the Forward Ports field, enter the ports to forward to the computer that triggered the rule (that is, specify the port number or range of port numbers that the application uses for incoming traffic). (Check the user documentation for the application.)
To specify a range of port numbers, separate the start and end port number with a hyphen.
7.
Ensure Enable is selected.
8.
Click Add .
9.
Click Save .
Removing Ports from the Port Triggering List
1.
Ensure you've enabled port triggering. See
"Enabling Port Triggering" on page 100 .
2.
Display the "Port trigger" window.
a.
Log in to the home page.
b. Click Advanced settings ( c.
Click Router > Port Trigger .
).
3.
To keep the entry in the list (in case you want to re-enable this entry later on), clear the Enable check box.
— or —
To remove the entry from the list: a.
Click the row that you want to remove.
A row of buttons ( Delete , OK , Cancel ) appears.
b. Click Delete .
101
Clear Spot 4G+ User Guide
102
DMZ Panel
DMZ stands for "demilitarized zone". You can select one computer to receive all unsolicited incoming connections.
The IP address of the DMZ is the default recipient of incoming packets (from the
Internet) that are not handled by port forwarding rules, port triggering rules, or
NAT'd connections:
1.
If port forwarding, port triggering, or both are enabled, incoming traffic is routed according to the port forwarding rules, port triggering rules, or NAT'd connections.
2.
If incoming traffic was not routed as a result of the above:
· If DMZ is enabled, then incoming traffic is routed to the computer that uses the IP address specified by the DMZ settings.
· If DMZ is not enabled, the incoming traffic is blocked.
Note: Putting a computer in the DMZ opens all the ports of that computer, and exposes that computer to various security risks. Use this option only as a last resort — if possible, use other options instead (for example, port forwarding or port triggering).
Before you can use or configure DMZ, you must enable it.
Enabling DMZ
Before you can use or configure DMZ, you must enable it.
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Router > Basic .
4.
Next to DMZ , select Enable .
5.
Click Save .
).
Configuring DMZ
To configure DMZ:
1.
Ensure you've enabled DMZ. See
2.
Display the DMZ panel of the Router tab.
a.
Log in to the home page.
b. Click Advanced settings ( c.
Click Router > DMZ .
).
3.
Specify the computer that you want exposed to the Internet: in the Destination
IP Address field, enter the IP address of the computer.
If you don't know how to find the IP address, see
"Finding the IP Address" on page 115 .
4.
In the Source IP Address section, specify what incoming traffic (not handled by port forwarding, port triggering, or NAT) to forward to this computer.
To forward all incoming traffic, click Any .
2131352
Rev 1.0 Apr.10
Settings
— or —
To forward incoming traffic from certain IP addresses: a.
Click Restriction .
b. In the two additional fields that are displayed, enter the start and end
IP addresses of a range.
5.
Using the DHCP Static IP Assignment List, assign an IP address based on
the MAC address of the computer that is in the DMZ. See "Assigning an
IP Address Based on a MAC Address" on page 97
.
— or —
On the computer that is in the DMZ, disable DHCP, and manually assign the
IP address, gateway, and DNS server.
Resetting the Software to Default Settings
Warning: If you reset the software to default settings:
• You must go through the device setup (
page 37 ), as if you've just purchased the device.
• Any changes you've made to the settings are lost.
Your 3G and 4G account information is not affected; after reset, the device remains provisioned for service.
You'll need to reset the software to default settings if:
• You've forgotten the administrator password.
• You've changed the DHCP settings such that the device is inoperable (for example, there's no communication with the device).
You have two options to initiate the reset:
•
Through the software. See "Resetting the Software to Default Settings
(Through the Browser Interface)" on page 104 .
• Through the reset button on the device. See the following section.
Resetting the Software to Default Settings (Through the Reset Button)
1.
Remove the battery compartment cover.
103
Clear Spot 4G+ User Guide
2.
Find the small hole below and to the right of the battery compartment. The reset button is inside this hole.
Reset button
3.
Insert a thin object (for example, the end of a paper clip) into the hole, and lightly press on the bottom of the hole for five or more seconds .
4.
Replace the battery compartment cover.
104
5.
Check the device LCD. If it displays "Reset to factory defaults? Press to accept", press the power button on the device.
6.
Follow the instructions on the device LCD.
Resetting the Software to Default Settings (Through the Browser Interface)
Warning: If you reset the software to default settings:
• You must go through the device setup (
page 37 ), as if you've just purchased the device.
• Any changes you've made to the settings are lost.
Your 3G and 4G account information is not affected; after reset, the device remains provisioned for service.
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Router > Basic .
4.
Click Router Settings Reset .
).
2131352
Rev 1.0 Apr.10
Settings
5.
Check the device LCD. If it displays "Reset to factory defaults? Press to accept", press the power button on the device.
6.
Follow the instructions on the device LCD.
Exporting and Importing Settings
Exporting Settings
Settings include configuration information for the device, network, and browser interface.
You can, for example, save the current configuration, then make some changes and test them. You can then use the Import button to restore (load) the saved configuration.
To export the settings to a text file:
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Basic .
4.
Click Export .
).
Importing Settings
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Basic .
).
4.
Browse to and click the file with the previously exported settings.
5.
Click Import .
Note: Your device may reset, and you may need to reconnect to Wi-Fi and the Internet.
See
"How Do I Connect to Wi-Fi?" on page 110
Logs
Logs Available
The following types of logs are available:
• Connect/disconnect. See the following section.
•
System events. See "System Events" on page 106
.
105
Clear Spot 4G+ User Guide
Connection History
The connection history shows the time of connections to and disconnections from the Internet.
Note: The connection history does not log the amount of data transferred. In the Internet
Connection Information window, you can view information on the current billing cycle and lifetime of the device; see
"Internet Connection Information" on page 57.
Enabling and Disabling Logging of Connect/Disconnects
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Log .
).
4.
In the Connect/Disconnect section, select Enable or Disable .
5.
Click save .
Exporting the Connection History
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Log .
).
4.
Ensure Connection/Disconnect is set to Enable .
5.
Click Export .
Clearing the Connection History
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Log .
).
4.
In the Connect/Disconnect section, click Clear log .
System Events
You can enable or disable, as a group, the logging of the following events:
• Software update available
• Network update available
• Primary WAN failover
• Primary WAN switchback
• Unexpected data connection loss
• Changes to miscellaneous settings
106 2131352
Rev 1.0 Apr.10
Settings
The following system events are always logged:
• Intrusion alerts
• Unexpected power loss
• Critical battery
• Critical temperature
• Routing hardware settings reset
• Firmware update
Enabling and Disabling Logging of System Events
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Log .
).
4.
In the Verbose System Event Logging section, select Enable or Disable .
5.
Click save .
Note: Certain events are always logged; see
Exporting System Events
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Log .
).
4.
Ensure Verbose System Event Logging is set to Enable .
5.
Click Export .
Clearing the System Events Log
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Log .
).
4.
Ensure Verbose System Event Logging is set to Enable .
5.
Click Clear log .
Setting the Method Used for Time Acquisition
Time information is stored in the connection history log and system events log.
To set the method used for obtaining the time:
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click Device > Log .
).
107
Clear Spot 4G+ User Guide
4.
Select the 3G or the NTP check box.
3G — Time information is obtained from the 3G (CDMA) network; this is more accurate than NTP, but requires 3G coverage.
NTP — The device's clock is synchronized to a Network Time Protocol server on the Internet; not as accurate as when using the 3G setting, but doesn't require 3G coverage. Use this setting if you have 4G but no 3G coverage.
Setup Pages
Welcome to Your Device Window - Select an Option
The “Welcome to Your Clear Spot 4G+ window” opens:
• Automatically, as part of the initial setup of your newly purchased device.
• When you click Admin Setup ( in).
) from the home page (you must be logged
Note: This window displays the administrator password and the address of the device home page. Please remember this information or write it down in a safe place.
This window provides several options.
• To keep the default settings of the device, select one of the following:
· The Internet (to start surfing)
· My Clear Spot 4G+'s home page (to view the device status, customize settings).
• To change security settings, select Set up my Clear Spot 4G+ .
108 2131352
6: Resources
More Information
Visiting the CLEAR Website
Check www.clear.com/support for product updates and support.
Contacting Customer Service
You can reach CLEAR Customer Service by:
• Visiting www.clear.com/support
Online Help
1.
In the browser interface, click the Help button ( ) and, from the menu, select Online Help .
The Help system opens in a new Web browser window or tab.
You have several options to find the information you need:
• Browse the Table of Contents.
• Use the Index or Search feature: click the appropriate button in the lower left part of the help window, and type the information you're looking for.
Other Ways to View Help Information
• Some windows have a icon. Click the icon to view Help information.
• When you move the cursor over a field or button in Advanced
Settings , help information, if available, appears to the right of the window.
Contextual Help in the Advanced Settings Window
When you move the cursor over a field or button in Advanced Settings , help information on this item, if available, appears to the right of the window.
To turn this feature on or off:
1.
Ensure you're logged in to the home page.
2.
Click Advanced settings > Device > Basic .
3.
Set Help for Advanced Settings to Show or Hide .
4.
Click Save .
6
Rev 1.0 Apr.10
109
Clear Spot 4G+ User Guide
Frequently Asked Questions
How Can I Tell I'm Connected to 3G/4G?
When you're connected:
• The 3G or 4G icon (on the left side of the home page) is solid. For example,
.
• The bottom area of the device LCD, the Virtual Device, and the Mini Window show the data transfer icon and data transfer information (amount of data; connection duration).
How Do I Connect to Wi-Fi?
You may have to manually connect to Wi-Fi after certain events — for example, as part of the initial device setup, or after a software update.
Tip: The Wi-Fi network name is displayed on the device LCD.
1.
Do one of the following, depending on your operating system.
Windows
Windows 7 : Right-click the icon in the system tray.
Windows Vista : Click Control Panel > Network and Internet > Network and Sharing
Center > Connect to a network .
Windows XP : Click Control Panel > Network Connections > Wireless Network
Connections > View available wireless networks .
Mac
Click the AirPort icon
Linux
(in the upper right corner of your screen).
Please see the user documentation of the Linux distribution.
Other operating systems
Please see the user documentation for your operating system or computer.
2.
Select the Wi-Fi network provided by the Clear Spot 4G+ personal hotspot and connect to it. (If prompted for a network key/security key/password, enter the Wi-Fi password.)
What Do I Do if I Forgot the Wi-Fi Password?
• If the Wi-Fi Password Reminder feature is enabled, display the password on
the device. See "Wi-Fi Password Reminder" on page 88 .
• Connect the device to your computer through USB, then log in and view the
Wi-Fi password (in Advanced settings > Wi-Fi > Security ). Write the password down in a safe place. See
"Connecting Through USB" on page 30.
110 2131352
Rev 1.0 Apr.10
Resources
Note: If you've forgotten both the Wi-Fi password and the administrator (login) password, then you must reset the software to default settings. See
Default Settings" on page 103.
What Do I Do if I Forgot the Administrator Password?
1.
Reset the software to default settings. See "Resetting the Software to Default
2.
Go through the device setup, during which the administrator password will be displayed; write it down in a safe place. See
"Setting Up the Device" on page 37
.
How Do I Access My Corporate Network Through a
VPN?
1.
Establish a connection to the 3G/4G network.
2.
Launch the extranet client provided by your company.
3.
Supply the appropriate user name and password to gain access.
For support, contact your company help desk.
Are Terminal Sessions Supported?
Terminal sessions (for example, via telnet or ssh ) are not supported.
Tips
Extending Battery Life
• When you're not using the device, turn it off, or end the 3G/4G connection.
(Click Disconnect on the home page).
• Connect the device, through the USB cable, to the power adapter or a computer, and disable Wi-Fi. See
"Disabling Wi-Fi When Connected Through
.
• Adjust the LCD — do one or more of the following:
· Turn off the LCD ( Advanced settings > Device > Display > LCD Backlight ).
· Decrease the brightness of the LCD ( Advanced settings > Device > Display
> Backlight Settings > On Battery/USB Power ).
· Set the LCD to turn off sooner. See "Setting the LCD Timeout" on page 72
.
• Configure the setting (for when battery powered or connected via USB) to
"Better battery life" ( Advanced settings > Wi-Fi > Network > Battery or
USB powered ).
•
Enable standby (low power) mode. See "Standby (Low Power) Mode" on page 56
.
• Turn off the lighting of the power button (i.e. LED) ( Advanced settings
> Device > Display > Power Button LED ).
111
Clear Spot 4G+ User Guide
112
• Limit the number of Wi-Fi users ( Advanced settings > Wi-Fi > Network > Max
Number of Users ).
• If you have 3G but not 4G coverage, set WAN Mode to "3G only" ( Advanced settings > WAN > Setup > WAN Mode ).
Device Location
• Avoid moisture or extreme temperatures.
• For improved reception, place the device near a closed window.
• Place your device within easy reach of a reliable power supply and the computer to which it will be connected.
Improving Signal Strength
• Ensure you're inside the network coverage area.
• Try reorienting your device.
• Move the device and your computer to another location — you may be in or near a structure that is blocking the signal. Every obstacle (for example, walls, ceilings, furniture) between the Clear Spot 4G+ personal hotspot and other wireless devices decreases the signal strength.
• Place the device in a centralized location, as high as possible in the room.
• Make sure there’s plenty of space around your device to provide the best signal reception.
• Keep the device at least 3-6 feet away from electrical devices that generate
RF interference (for example, microwaves, TVs, 2.4 GHz cordless phones, cellular phones, baby monitors, wireless speakers). If you're not using these electrical devices, turn them off.
• If possible, place your devices so that the signal passes through open doorways or drywall, as opposed to concrete, brick, metal, walls with insulation, and so on.
• If you cannot obtain service, contact CLEAR — a network or account problem may be preventing you from obtaining service.
Improving 3G Network Service
To improve your network service, periodically check for PRL and profile updates.
The PRL (Preferred Roaming List) is an account configuration item set by your service provider. It controls the radio channels and network carrier used by the
3G modem.
To check for these updates:
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click WAN > Setup .
).
4.
Click Update 3G PRL .
5.
After the update checking is completed, click Update 3G Profile .
2131352
Resources
Improving Wi-Fi Performance
• Try a different channel number. See
•
Check whether any device updates are available. See "Updates" on page 64.
•
See the tips in "Improving Signal Strength" on page 112 .
• Limit the number of Wi-Fi users ( Advanced settings > Wi-Fi > Network > Max
Number of Users ).
• Select a longer Wi-Fi range. ( Advanced settings > Wi-Fi > Network > Longer Wi-Fi range [two locations: Battery or USB Powered , and AC Powered ])
Windows XP Users
1.
Open the Device Manager.
a.
Click start > Settings > Control Panel .
b. Double-click System .
c.
Click Hardware .
d. Click Device Manager .
2.
Double-click Network adapters .
3.
Double-click the Wi-Fi client network adapter of your computer — for example, “Intel(R) WiFi Link 5100 AGN” in the following screenshot.
Rev 1.0 Apr.10
4.
If the Wi-Fi client network adapter is by Intel, click Advanced and, in the
Property list, click Power Management and move the slider all the way to the right (to Highest ). Click OK .
— or —
113
Clear Spot 4G+ User Guide
If the Wi-Fi client network adapter is not by Intel, select a configuration with minimal power savings (to maximize throughput).
Note: The above settings are often controlled by 3rd-party value-add applications and may be automatically changed. If Wi-Fi performance improves for a while after performing the above steps, but then declines, recheck the above settings.
Security Tips
• Change the Wi-Fi network name (SSID) and Wi-Fi password on a regular basis. See
"SSID (Wi-Fi Network Name)" on page 84
and
• Disable SSID Broadcast. See
.
• Use the highest level of Wi-Fi security that your devices support. See
•
Change the login password. See "Changing the Administrator Password" on page 75
.
• Use MAC filtering to specify computers that are or aren't allowed to connect
to the network. See "MAC Filter Panel" on page 83.
Finding the MAC Address
You'll need to know the MAC address of a device, when performing any of the following:
• Assigning an IP address based on a MAC address (when using DHCP). See
"DHCP Static IP Assignment List" on page 97
.
•
Allowing or denying computers access to the network. See "Allowing or
Denying Computers Access to the Network" on page 88.
Tip: You can display a list of connected devices, including the MAC address of each device: click
List of connected devices
, available from
Advanced settings > Wi-Fi
> MAC Filter
and
Advanced settings > Wi-Fi > Network
.
The steps to finding the MAC address of a device vary, depending on your operating system.
Windows
1.
Open a command prompt window.
a.
Click start and Run .
b. Type cmd or command , and click OK .
2.
At the command prompt, type ipconfig/all and press Enter .
3.
Write down the Physical Address for the entry that relates to the wireless network connection; it appears as a series of numbers and letters — this is the MAC address of your wireless adapter.
114 2131352
Rev 1.0 Apr.10
Resources
Mac OS X
1.
From the Apple menu ( ), select System Preferences .
2.
Select Network .
3.
Select the adapter that is connecting to the routing hardware.
4.
Select Advanced .
5.
Select Ethernet . The Ethernet ID is listed. This is the same as the MAC address.
Linux
Please see the user documentation of the Linux distribution.
Other operating systems
Please see the user documentation for your operating system or computer.
Finding the IP Address
You'll need to know the IP address of a device, when configuring any of the following:
• Port forwarding
• Port triggering
• DMZ
• Static DHCP features
To find the IP address of a device:
Windows
1.
Open a command prompt window.
a.
Click start and Run .
b. Type cmd or command , and click OK .
2.
At the command prompt, type ipconfig and press Enter .
3.
Write down the IP Address for the entry that relates to the wireless network connection. (The IP address might be listed under "Ipv4 Address", or something similar.)
Mac OS X
1.
From the Apple menu ( ), select System Preferences .
2.
Select Network .
3.
Select the wireless adapter. The IP address is displayed in the right pane.
Other operating systems
Please see the user documentation for your operating system or computer.
115
Clear Spot 4G+ User Guide
Troubleshooting Tips
General tips
• Check the system events log. See
"Exporting System Events" on page 107 .
• If some settings are preventing you from connecting to Wi-Fi, connect to the
.
• Go to www.clear.com/support to access troubleshooting and other resources.
• The knowledge base at the Sierra Wireless website ( www.sierrawireless.com/ support/customer_help.aspx
) may also be useful.
LCD Is Dark
The LCD is dark and is not displaying any text or icons if:
• The device is turned on and:
· The LCD is turned off ( Advanced settings > Device > Display > LCD Backlight ).
· The LCD is turned on, but the LCD is dormant (inactivity timeout). To make the LCD active, briefly press the power button on the device.
· The device is in standby (low power) mode. To exit this mode, briefly press the power button on the device.
• The device is turned off.
To turn the device on: a.
Ensure a battery is inserted into the device.
b. Press the power button on the device for approximately two seconds.
If the LCD is still dark, use the USB cable to connect the device to the power adapter or to a computer.
Insufficient Signal Strength
If you have insufficient signal strength, the icon of the home page).
is displayed (on the left side
Insufficient signal strength may occur because:
• You are outside the network coverage area.
• Your device’s internal antenna is pointing in the wrong direction.
• You are in or near a structure that is blocking the signal.
• You are near a device that is causing radio signal interference.
• A network or account problem is preventing you from obtaining service.
See also "Improving Signal Strength" on page 112 .
116 2131352
Rev 1.0 Apr.10
Resources
Messages Displayed on the Device LCD
See also "SD Card Error" on page 49.
3G Activation Failed
If this message is displayed on the device LCD or in the 3G Activation Required alert window (after you've attempted activation):
1.
Ensure you're in 3G coverage and the signal strength is strong.
2.
Turn the device off and on. See
"Turning Your Device Off" on page 48 and
"Turning Your Device On" on page 33 .
3.
If the "Activation failed" message is still displayed, prepare the following, and contact CLEAR:
· Your billing information.
· ESN of the device (displayed on the packaging, on the device [under the battery], and at Advanced settings > Device > About ).
Connecting to 3G/4G
If the LCD displays this message for a long time:
1.
Check the signal strength. If it is weak, try the tips in "Improving Signal
.
2.
Try a different Connection Preferences setting. See
"Mobile Broadband Information and Settings" on page 53 .
3.
Turn the device off and on. See
"Turning Your Device Off" on page 48 and
"Turning Your Device On" on page 33 .
4.
Update the 3G profile: click Advanced settings > WAN > Setup > Update 3G
Profile .
5.
If you're still unable to connect to 3G/4G, contact CLEAR.
Connection Error
If this message persists on the device LCD, update the 3G profile:
1.
Log in to the home page.
2.
Click Advanced settings (
3.
Click WAN > Setup .
4.
Click Update 3G Profile .
).
5.
If an error message and number are displayed on the LCD after the update, note the information and contact CLEAR.
3G Activation Required
If the LCD displays this message, display the 3G Activation Required alert and start the activation:
1.
In the Admin Login section (in the upper left area of the home page), enter the administrator password (1–20 characters/numbers). (The default password is
"admin".)
2.
Click OK .
117
Clear Spot 4G+ User Guide
3.
Click the alerts icon to display the alert window.
4.
If more than one alert is available, use the and buttons (at the top of the alert window) to browse to the "3G Activation Required" alert.
5.
In the 3G Activation Required alert window, click Activate now .
Tip: Alternatively, click Advanced settings > WAN > Setup > Update 3G Profile .
Searching for Network
The LCD displays this message until a 3G or 4G network is acquired.
If this message persists, see the tips in "Cannot Connect to the 3G/4G Network" on page 120
.
Update Failed
If this message appears on the device LCD or in the 3G Network Update
Available or Software Update Available alert windows (after you've attempted the update):
1.
Ensure your device is connected to the power adapter or computer, through the USB cable.
Note: If you’ll be using USB for data transfer (and not just for charging the device), you must install the device driver. See
"Making a Tethered Connection" on page 43 .
2.
Retry the update.
3.
If the "Update failed" message is still displayed, contact CLEAR.
Cannot Connect to Wi-Fi
If your computer cannot connect to the Wi-Fi network of the Clear Spot 4G+ personal hotspot, ensure that:
• The maximum number of Wi-Fi users has not been reached. (To determine the number of connected Wi-Fi users and set the maximum, see
Information and Settings" on page 55).
• You're connecting to the correct Wi-Fi network (SSID), and you're using the correct Wi-Fi password. If the Wi-Fi Password Reminder feature is enabled
(
), you can use it to display the SSID and Wi-Fi password on the device LCD.
• Nobody has changed the name or password of the Wi-Fi network. If the Wi-Fi
Password Reminder feature is enabled (
page 88 ), you can use it to display
the SSID and Wi-Fi password on the device LCD.
• Nobody is connected through the USB cable when Disable Wi-Fi when connected via USB is selected.
• Your computer supports the type of Wi-Fi security that the network is set to use.
118 2131352
Rev 1.0 Apr.10
Resources
Note: All the devices used with the Clear Spot 4G+ personal hotspot must support the selected security type.
• Your computer supports Wi-Fi 802.11g (if Basic Rate is set, in Advanced settings > Wi-Fi > Network , to 802.11b/g compatibility ).
•
Your computer has not been blocked, through MAC filtering. See "Specifying
Computers That Are Not Allowed to Access the Network" on page 89 .
Tip: If some settings are preventing you from connecting to Wi-Fi, connect to the device
through the USB cable, and then change the settings. See "Requirements for a USB
Tethered Connection" on page 43 and "Making a Tethered Connection" on page 43
.
Cannot Display the Home Page
Your Web browser may display an error message when you try to display the home page. The error message depends on your Web browser.
• "Could not connect to remote server" (Opera)
• "Internet Explorer cannot display the webpage" (Internet Explorer)
• "Oops! This link appears to be broken" (Google Chrome)
• "Safari can’t open the page" (Safari)
• "The connection has timed out" (FireFox)
Check the following:
• The device is turned on. See
"Turning Your Device On" on page 33 .
• You have established a connection to the device (through Wi-Fi or through the
USB cable).
• Ensure you're typing the correct address in the Web browser.
· Try http://<SSID> , where <SSID> is as displayed on the device LCD.
· If the home page is still not displayed, try http://192.168.0.1
or, if you're using custom routing settings, replace "192.168.0.1" with the appropriate
IP address.
• The Web browser is a recent version, and Java-enabled. The following are recommended:
· Internet Explorer (version 6.0 or higher)
· Mozilla Firefox (version 2.0 or higher)
· Google Chrome (version 2.0.172.28 or higher)
· Apple Safari (version 2.0 or higher)
· Opera version 9.64
• If your computer has other adapters (for example, Ethernet) connected to other networks, disable or remove them from your computer.
• If Internet security software is running on your computer, disable it and see whether the error message still occurs. Some firewall software may block access to the home page.
• If DHCP is enabled on the device, ensure DHCP is enabled on your computer. See
119
Clear Spot 4G+ User Guide
• Check your Web browser settings.
a.
Open the Control Panel in Windows.
b. Double-click Internet Options .
c.
From the Security tab, restore the default settings.
d. From the Connections tab, select Never dial a connection .
e.
From the Advanced tab, restore the default settings.
f.
Close and reopen your Web browser.
• Disconnect the device from your computer (if you're using the USB cable).
Remove the battery from the device. Reinsert the battery.
If, after checking all of the above, you still cannot display the home page, consider
resetting the software to default settings. See "Resetting the Software to Default
Cannot Connect to the 3G/4G Network
• Ensure your computer is connected to the device (through the USB cable or
Wi-Fi). See "How Do I Connect to Wi-Fi?" on page 110
.
• Try the tips in
"Improving Signal Strength" on page 112
.
• Check the WAN Mode setting ( Advanced settings > WAN > Setup ). For example, if it's set to 4G only , you won't be able to connect if:
· You don't have 4G coverage.
• Check with CLEAR — a network or account problem may be preventing your device from obtaining service.
Cannot Check for Updates
Ensure your device is connected to the power adapter or computer, through the
USB cable.
Note: If you’ll be using USB for data transfer (and not just for charging the device), you must install the device driver. See
"Making a Tethered Connection" on page 43 .
Sounds are Enabled, but the Device Doesn't Generate
Any Sounds
Check that sounds are not turned off through the Mute switch on the device. See
120 2131352
7: Technical Specifications, Safety Information, and Regulatory Information
Technical Specifications
LED Operation
See
"Using the Power Button to Determine the Device State" on page 34.
Radio Frequency and Electrical Specifications
Approvals
Battery
Current
Transmit
Receive
FCC
Size: 1800 mAh
Duration for full charge:
• AC charger: 1.5 hours
• PC USB cable: 3.6 hours
Charge life:
• 4 hours under standard use
• 3 hours of continuous use
Maximum: 1000 mA
Standby:
• 48 mA (1xEV-DO/IS2000 hybrid mode)
• 48 (WiMAX)
PCS: 1850 to 1910 MHz
Cellular: 824 to 849 MHz
WiMAX: 2495 to 2690 MHz
PCS: 1930 to 1990 MHz
Cellular: 869 to 894 MHz
WiMAX: 2495 to 2690 MHz
GPS: 1575.42 MHz
7
Rev 1.0 Apr.10
121
Clear Spot 4G+ User Guide
Software Specifications
CDMA (3G) specification IS-2000 Release 0
Data service IS-707A
WiMAX (4G) specification IEEE 802.16e-2005
Wi-Fi specification
Wi-Fi security and encryption protocols
IEEE 802.11b
IEEE 802.11g
WEP Open & Shared
WEP-64
WEP-128
WPA-Personal TKIP & AES (Pre-Shared Key or WPA-
PSK)
WPA2-Personal TKIP & AES (WPA2-PSK)
WPA+WPA2-Personal (WPA+WPA2 PSK)
SMS (IS-637)
FAX
IOTA
OTASP (IS-683A, IS-
683B, IS-683C)
Not supported
Not supported
Supported
Supported
Supported
Supported
OTAPA
PRL (Preferred Roaming
List)
Authentication
Voice
NAM
Position Location
TTY/Accessibility
Mobile IP
Network protocols
(routing hardware)
VPN
Supported
Not supported
Single
Standalone
Not supported
Supported
TCP, UDP, ARP, RARP, ICMP
Pass-through of the following VPN types:
• PPTP
• IPSec
Tunneling of multiple VPN sessions simultaneously is supported.
122 2131352
Rev 1.0 Apr.10
Technical Specifications, Safety Information, and Regulatory Information
Environmental Specifications
Operating temperature
Storage temperature
Humidity
Vibration
Drop
-20 to +55°C
-40 to +85°C
95%, non-condensing
10-1000 Hz, 6G, 60 min/axis, 3 hrs total (non-operating)
1 m on concrete
Mechanical Specifications
Dimensions (W x L x H) 81 mm x 81 mm x 16 mm
Power button
Headset jack
LED
Supported
Not supported
White
Safety Information
Proper Battery Use and Disposal
Note: Improper battery use may result in a fire, explosion, or other hazard.
To ensure safe and responsible battery use:
• Do not open, disassemble, puncture, crush, bend, or shred.
• Do not expose to water or other liquids, fire, explosion, or other hazards.
• Use the battery only in the Clear Spot 4G+ personal hotspot.
• If using with a charger, use only the power adapter supplied with the device.
• Do not short circuit the battery.
• When replacing a battery, use the same model of battery that was supplied with the device.
• Follow local regulations when disposing of a used battery.
• Avoid dropping the device or the battery. If dropped and you suspect damage, take it to a service center for inspection.
123
Clear Spot 4G+ User Guide
Regulatory Notices
The design of the Clear Spot 4G+ personal hotspot complies with U.S. Federal
Communications Commission (FCC) guidelines respecting safety levels of radio frequency (RF) exposure for mobile devices, which in turn are consistent with the following safety standards previously set by U.S. and international standards bodies:
• ANSI / IEEE C95.1-1999, IEEE Standard for Safety Levels with Respect to Human
Exposure to Radio Frequency Electromagnetic Fields, 3kHz to 300 GHz
• National Council on Radiation Protection and Measurements (NCRP) Report
86, 1986, Biological Effects and Exposure Criteria for Radio Frequency Electromagnetic Fields
• International Commission on Non-Ionising Radiation Protection (ICNIRP)
1998, Guidelines for limiting exposure to time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz)
FCC ID : N7N-MHS801.
RF Exposure - This device is only authorized for use in a mobile application. At least 20 cm (8 inches) of separation distance between the Clear Spot 4G+ personal hotspot and the user's body must be maintained at all times.
Warning: (EMI) - United States FCC Information - This equipment has been tested and found to comply with the limits for a Class B computing device peripheral, pursuant to
Parts 15 and 27 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Parts 15 and 27 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.
124 2131352
Index
Numerics
3G
3G panel of the WAN tab
activation failed
activation information, viewing
activation, initiate
configuration, resetting to default settings
data transmission rates
improving network service, tips
lifetime data
Mobile Broadband Information window
overview
PRL version
,
service type
status
3G (time acquisition method)
3G Activation Required (alert)
3G Activation Required (LCD message)
3G Network Update Available (alert)
3G Only
3G panel of the WAN tab
3G/4G Mobile Broadband Information window
3G/4G Off
4G
4G panel of the WAN tab
Base Station ID (BSID)
configuration, resetting to default settings
connection status
coverage type (service type)
data transmission rates
lifetime data
Mobile Broadband Information window
network access provider (NAP-ID)
network service provider (NSP-ID)
overview
4G Only
4G Preferred
,
802.11 standards supported
Rev 1.0 Apr.10
A
About panel of the Device tab
about this guide
AC charger (power adapter)
AC powered
,
access to the network, configuring
,
account information
,
acquisition, time, method used for
Activate now
activating network service
Activation complete!
Activation Date
,
Activation Required (alert)
Activation Status
,
activation, 3G
3G Activation Required
3G Activation Required alert
date of original activation
failed
initiate
Active network
,
Admin Login area of the home page
Admin Password
Admin Setup button
Administrator + Guest
administrator password changing
forgotten; what do I do?
administrator, logging in as
Advanced Settings window
AES
alert
3G Activation Required
Alert window
audio, enabling/disabling
critical battery level alert
displaying
low battery
Network Update Available
SD Card Error
Software Update Available
Sounds panel of the Device tab
Alert when (low battery)
Alert window
Allow all in list (giving computers access to the network)
125
Clear Spot 4G+ User Guide allowing computers access to the network
Apple Safari
Application (port forwarding)
application notes
application updates
automatically check for updates
automatically log in disabling for a specific computer
enabling
viewing list of computers set to automatically log in
B baby monitors
Backlight (LCD on the device) brightness
turning off automatically
turning on or off
Backlight Settings
Base Station ID (BSID)
Basic panel of the Device tab
Basic panel of the Router tab
Basic Rate
battery
"Better battery life" setting
,
Battery Information and Settings window
charging
critical battery level alert
icon
installing
low battery alert
low battery, play sound
overview
proper use and disposal
specifications
tips on extending battery life
Battery Information and Settings window
Battery or USB powered
Better battery life
,
billing cycle data statistics
blacklist
,
Block (block a computer's access to the Wi-Fi network of the device)
Block all in list
,
box contents
brightness of LCD
broadcast the SSID (Wi-Fi network name)
browser interface home page
browser interface updates
browsers supported
BSID (Base Station ID)
buttons below the virtual device
top of home page
C cannot connect to the 3G/4G network
cannot connect to Wi-Fi
cannot display the home page
care of your device
Carrier to Interference-plus-Noise Ratio (CINR)
CDMA
cell phones
Center frequency
Certificate information
charger (power adapter)
charging the device
check for updates automatically
manually
Check for updates now
Chrome browser
CINR (Carrier to Interference-plus-Noise Ratio)
Clear Log (connection history)
Clear Log (system events)
components of your device
Connect Automatically
Connect button
connect to Internet alert
,
cannot connect
improving 3G network service, tips
launching a connection
sharing your connection
Connect/Disconnect
connected how to tell you're connected to 3G/4G
icon
play sound when connected or disconnected
Wi-Fi users information
126 2131352
connected computers, displaying a list of
Connected Users window
connecting the device to your computer
USB
Wi-Fi
Connecting to 3G/4G message
connection ending
history log
improving 3G network service, tips
information, displaying
launching
lost (audio alert) - Internet Disconnected
settings
,
sharing
state
,
status, 3G
status, 4G
Wi-Fi users information
Connection Error message
connection history clearing
description
enabling logging
exporting
Connection Preferences
contents, package
contextual (field-level) Help
cordless phones
corporate network, accessing through VPN
Could not connect to remote server
coverage type (service type)
3G
4G
coverage type(s) available
critical battery level alert
critical temperature alert
current, electrical (specification)
Customer Service, contacting
D dark LCD
data statistics for the current connection session
data transferred
,
data transmission rates
default settings
Index
3G/4G configuration, resetting
software, resetting
software, resetting (through the reset button on the device)
denying computers access to your network
Destination IP Address
device information, viewing
,
name (host name)
overview
device driver, installing
device name (host name)
Device tab
About panel
Basic panel
Display panel
Log panel
microSD card panel
Sounds panel
DHCP clients, maximum number of
description
enabling
lease time
start and end address
Static IP Assignment List
DHCP IP Address Range
DHCP Lease Time
DHCP Server
DHCP Static IP Assignment List
dimensions of device
Disable Wi-Fi upon USB-PC
Disable Wi-Fi when connected via USB
,
Disconnect button
Display panel of the Device tab
displaying home page
disposal of battery
DMZ configuring
DMZ panel of the Router tab
enabling
DMZ panel of the Router tab
DNS Mode
DNS Relay
document overview
dormant
download speeds
drawing of hardware
Rev 1.0 Apr.10
127
Clear Spot 4G+ User Guide driver, installing
drop specification
duration for full charge
duration, session
,
E
Ec/Io
,
electrical specifications
Electronic Serial Number (ESN)
email server, accessing
Enable SD Card
End (port, for port forwarding)
environmental specifications
ESN (Electronic Serial Number)
Export Router Settings
exporting connection history
settings
system event log
F
Failover wait time
failure, device startup audio alert
FAQ (Frequently Asked Questions)
FCC (regulatory) notices
FCC ID
feedback
field-level (contextual) Help
Firefox browser
firewall software
firmware version
3G modem
,
4G modem
,
routing hardware component
Wi-Fi
firmware, upgrade from a file
folder name, microSD card
forgot administrator password
forgot Wi-Fi password
Forward Ports
Fragmentation Threshold
frequencies, transmit and receive
Frequently Asked Questions (FAQ)
FTP server, accessing
full charge
128
G gaming, Internet
Get Started guide
Google Chrome
Guaranteed Update
Guest Password (for microSD card access)
Guest Username (for microSD card access)
H hardware
Help button
Help files, updates
Help for Advanced Settings
help, getting
CLEAR website
Customer Service, contacting
FAQ (Frequently Asked Questions)
tips
troubleshooting
Help, online
home page buttons along the top
cannot display
description
displaying
logging in
vertical row of icons and text
virtual device
host name
,
humidity specification
I icons home page (vertical row of icons and text)
LCD
Import Router Settings
important information booklet
importing settings
improving signal strength
IMSI (International Mobile Station Identity)
,
information about your device
installing the device
International Mobile Station Identity (IMSI)
,
2131352
Internet Connected
,
,
Internet Connection Information window
connection lost (alert)
,
Internet Disconnected
,
Internet Explorer
Internet Explorer cannot display the webpage
Internet gaming
Internet telephony
IOTA
IP address assigning, based on MAC address
DHCP, range
DMZ computer
finding for a device
removing an address based on MAC address
routing hardware
WWAN, of the device
IP Address (port forwarding)
K knowledge base
L
LAN panel of the Router tab
Last user has joined
Last User Has Left
LCD brightness
dark
icons on LCD
not lit
timeout
turning off automatically
turning on or off
LCD Backlight
lease time, DHCP
LED (Power button on the device) description
enabling
interpreting
location
lifetime data
Index lifetime of product total data transferred
Link SSID and Host Name
list of connected computers, displaying
List of connected devices
Load 3G PRL
log connection history
system events
log in automatically disabling for a specific computer
enabling
viewing list of computers set to automatically log in
Log panel of the Device tab
logging in automatically
steps to log in
login password changing
forgotten; what do I do?
Longer Wi-Fi range
,
Low battery
,
,
low battery alert
low power mode (Standby Timer)
M
MAC (Media Access Control) filter
,
MAC address
4G modem
assigning an IP address based on MAC address
finding for a device
Wi-Fi users
Mac device driver, installing
MAC filter
MAC Filter List
MAC filter mode
,
MAC Filter panel of the Wi-Fi tab
maintenance of your device
manufacturer information
,
Max DHCP clients
Max Number of Users
Max number of Wi-Fi users
Max Wi-Fi users
maximum number of Wi-Fi users
mechanical specifications
Rev 1.0 Apr.10
129
Clear Spot 4G+ User Guide
Media Access Control
MEID (Mobile Equipment Identifier)
,
microSD card accessing
enabling
inserting
location of slot
microSD Card panel of the Device tab
overview
removing from the device
SD Card Error (alert)
SD Card Information and Settings window
shared folder name
microSD Shared Folder Name
microwaves
Mini Window
Mobile Broadband Information window
Mobile Equipment Identifier (MEID)
,
Mobile Station ID (MSID)
,
model information
,
Mozilla Firefox
MSID (Mobile Station ID)
,
mute switch, location
N
NAI (Network Access Identifier)
NAP-ID (Network Access Provider ID)
network
3G, overview
4G Base Station ID (BSID)
4G network access provider (NAP-ID)
4G service provider (NSP-ID)
4G, overview
active network
cannot connect
name, Wi-Fi (SSID)
network operator
protocols supported
Network Access Identifier (NAI)
network access provider, 4G (NAP-ID)
network access, configuring
network operator
4G (NSP-ID)
viewing
,
Network panel of the Wi-Fi tab
network service
3G, tips on improving service
activating
Network Time Protocol (NTP)
Network Update Available (alert)
,
network, corporate, accessing through VPN
No filtering
no service icon
not connected
notices regulatory
NSP-ID (Network Service Provider ID)
NTP (Network Time Protocol)
O
Obtain an IP address automatically
On AC Power
On Battery/USB Power
online games
,
online Help displaying
getting updates
Oops! This link appears to be broken
Opera browser
operating temperature
operator, network
,
original activation date
OTAPA
OTASP
overview of this document
P package contents
password reminder, Wi-Fi
password, administrator changing
forgotten; what do I do?
password, Wi-Fi changing
forgotten; what do I do?
overview
reminder
pay-as-you-go
performance, Wi-Fi, tips on improving
place for your device, tips
Plug and Play, Universal (UPnP)
130 2131352
Port Forward panel of the Router tab
port forwarding description
disabling for an application
enabling
enabling for an application
Port Trigger panel of the Router tab
port triggering description
enabling
ports, adding
ports, removing
power adapter
Power button (on the device) description
interpreting
location
Power Button LED field
Power Off button
,
power settings
AC outlet, connected to
battery-powered
tips on extending battery life
USB powered
powering the device off
powering the device on
Preable
Preferred Roaming List (PRL) update
PRI version
3G component
routing hardware
,
PRL update alert (update available)
load a file
PRL version
3G modem
,
problems
Protocol (port forwarding)
Protocol (port triggering)
protocols, network, supported
Q questions, frequently asked (FAQ)
Index
R radio frequency (RF) specifications
Realm
receive frequencies
Received (amount of data transferred)
recharging the battery
regulatory notices
Remember me
Remember me clients list
Remember me computers, view list of
reminder, Wi-Fi password
Remote Desktop, accessing
requirements installation
USB
reset button location
resetting the software to default settings
Reset Device to Factory Defaults button
resetting the 3G/4G configuration to default settings
resetting the software to default settings through the browser interface
through the reset button on the device
restarting the device
Restriction field
RF (Radio Frequency) specifications
router
Router IP Address
Router PRI Version
Router setting reset audio alert
performing
Router tab
DMZ panel
LAN panel
Port Forward panel
Port Trigger panel
routing hardware firmware version
IP address
play sound when routing hardware resets
PRI version
,
resetting to default settings (through the reset button on the device)
resetting to default settings (through the software)
Rev 1.0 Apr.10
131
Clear Spot 4G+ User Guide subnet mask
RSSI (signal strength) improving
insufficient
viewing
RTS Threshold
Rx (receive) frequencies
S
Safari browser
Safari can’t open the page
SD Card error (alert)
SD Card Information and Settings window
Searching for Network
security
MAC filtering
network access, configuring
SPI (Stateful Packet Inspection)
tips
Wi-Fi
Security panel of the Wi-Fi tab
Sent (amount of data transferred)
server, accessing
service icon
Service Programming Code (SPC)
service type
3G
session duration
,
Session total data
Set Guest Password (for microSD card access)
Set Guest Username (for microSD card access)
Set up my device
setting up the device
settings exporting
importing
Setup panel of the WAN tab
shared folder name, microSD card
sharing your Internet connection
short text messaging (SMS)
Shorter Wi-Fi range
,
SID (System ID)
Sierra Wireless knowledge base
Signal Quality window
signal strength improving
insufficient
viewing
size of device
SMS
software resetting to default settings
specifications
updates
Software Update Available (alert)
,
Software Version
,
sounds enabling/disabling all (Mute switch)
enabling/disabling individually
Sounds panel of the Device tab
Sounds window
Source IP Address
SPC (Service Programming Code)
specifications electrical
environmental
mechanical
radio frequency (RF)
software
speeds, download
SPI (Stateful Packet Inspection)
ssh support
SSID (Wi-Fi network name) broadcast
changing
description
Host Name, link to
SSID Broadcast
Standby Timer
Standby Timer on Battery or USB
Start (port, for port forwarding)
start day of the billing cycle, changing
Starts on day
startup failure, device (audio alert)
Stateful Packet Inspection (SPI)
Static IP Assignment List, DHCP
storage guidelines
storage temperature
subnet mask
Support button
support, contacting
Switchback wait time
System alerts
,
system events log
132 2131352
clearing
enabling
exporting
types of events included
System ID (SID)
system requirements
T
TCP/IP settings
technical support, contacting
telnet support
temperature specifications
temperature, critical (audio alert)
terminal sessions
tethered connection making
requirements
text messaging (SMS)
The connection has timed out
timeout connection timeout (cannot display the home
LCD
page)
tips
TKIP/AES
,
Total (amount of data transferred)
Total data
trademarks
transmission rates
transmit frequencies
transmitter power
Trigger Ports
troubleshooting cannot connect to the 3G/4G network
cannot connect to Wi-Fi
cannot display the home page
general tips
TRU-Install
TTY
Turn Off Backlight
turning the device off
turning the device on
TVs
Tx (transmit) frequencies
Tx Power
Index
U
Universal Plug and Play (UPnP)
,
Update 3G PRL
Update 3G profile
Update Failed
Update firmware from file
updates
3G Network Update Available (alert)
automatically check
cannot check for
firmware, upgrade from a file
manually check
overview
PRL
Software Update Available (alert)
UPnP (Universal Plug and Play)
usage guidelines for your device
USB charging the device
connecting the device to your computer through USB
location
power settings
requirements
Wi-Fi, disabling when connected through
USB
user ID, 3G network
Username and Password Security
V
Verbose System Event Logging
vertical row of icons and text
vibration specification
video conferencing
virtual device
Voice over Internet Protocol (VoIP)
VoIP (Voice over Internet Protocol)
VPN accessing corporate network through
passthrough types supported
W wait time failover
Rev 1.0 Apr.10
133
Clear Spot 4G+ User Guide switchback
WAN mode
WAN tab
3G panel
4G panel
Setup panel
warning (EMI)
warning (software settings reset)
warranty
Web browsers supported
Web server, accessing
website
CLEAR
Sierra Wireless
Welcome to Your Device window - Select an
Option
WEP
,
whitelist
,
Wi-Fi alerts (user has joined, or left)
,
cannot connect
channel
configuring, overview
connected computers, displaying list of
connecting to
longer Wi-Fi range
,
MAC Filter panel of the Wi-Fi tab
maximum number of users
network name (SSID)
Network panel of the Wi-Fi tab
password
Password Reminder
password, forgot
performance, tips on improving
security
security and encryption protocols supported
Security panel of the Wi-Fi tab
sounds when user joins or leaves
SSID (Wi-Fi network name)
USB tethered mode
Wi-Fi users information
Wi-Fi Channel
Wi-Fi Firmware Version
Wi-Fi Passwordl
Wi-Fi Security Options window
Wi-Fi user has joined
,
Wi-Fi user has left
,
Windows device driver, installing
Windows XP
Wi-Fi performance, tips on improving
wireless speakers
WPA
,
WPA2
WWAN IP address of the device
X
XP, Windows
Wi-Fi performance, tips on improving
Y
Your device is now restarting (window)
134 2131352
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project