ROUSH Trunk Mounted Tool Box Kit Installation Instructions Kit Part Number 1310R08030006

ROUSH Trunk Mounted Tool Box Kit  Installation Instructions Kit Part Number 1310R08030006
®
ROUSH Trunk Mounted Tool Box Kit
Kit Part Number 1310R08030006
Application: 2010-11 Ford Mustang GT
Installation Instructions
Before installing your ROUSH Performance Product(s), read through the entire
installation procedure and check to make sure all items are present. Contact ROUSH
Customer Service at 1-800-59-ROUSH, 9:00 AM to 5:00 PM EST, weekdays, for any
questions regarding fit, missing parts or instructions that are unclear to you.
Note: The extra slot in the tool kit bottom foam liner is for your wheel lock key.
1310R08030006IM
Page 1 of 9
1-800-59-ROUSH
®
Packaging List for ROUSH Tool Kit
Part Description
Trunk Mounted Tool Box Kit
Trunk Tool Box
Hardware Kit - Trunk Tool Box
Adapter Bracket Assy (plastic w/ nut)
Bolt - 1/4”-20 Allen head cap
Washer - 1/4" Fender
Hardware Kit - Trunk Tool Box Mounting Kit
Mounting Bracket LH
Mounting Bracket RH
Screw - Self-drilling / tapping #8 TEK
Double sided tape - 1/2" x 3/4"
Template - Bracket Positioning ***
Template - Deck Lid Liner Cutting ***
Installation Instructions
*** Not shown
ROUSH Part Number
1310R08030006
R08030007
1305-R08030009
R08030008
1310R08030006HK
R08030029
R08030030
R07030003
131008030010
1310R08030006TPA
1310R08030006TPB
1310R08030006IM
Qty
1
1
1
2
2
2
1
1
1
6
1
1
1
1
Equipment and Supplies Required
Push Pin removing tool
Knife to cut Inner Trunk Liner
Center Punch & Hammer or a Self Impacting Center Punch
Drill with 1/4” Drive Adapter
1/4” Socket - 1/4” drive
3/16” Allen Wrench or 1/4 Drive Allen Socket
1310R08030006IM
Page 2 of 9
Masking Tape
Scissors
Small Screw Driver
1-800-59-ROUSH
®
LIMIT OF LIABILITY STATEMENT
The information contained in this publication was accurate and in effect at the time the
publication was approved for printing and is subject to change without notice or liability.
ROUSH Performance Products (RPP) reserves the right to revise the information
presented herein or to discontinue the production of parts described at any time.
SAFETY REQUIREMENTS
STOP! READ IMPORTANT SAFETY CAUTIONS AND WARNINGS BEFORE
PROCEEDING.
IMPORTANT SAFETY NOTICE
Appropriate disassembly, assembly methods and procedures are essential to ensure the
personal safety of the individual performing the kit installation. Improper installation
due to the failure to correctly follow these instructions could cause personal injury or
death. Read each step of the installation manual carefully before starting the actual
installation.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Always wear safety glasses for eye protection.
Place ignition switch in the OFF position.
Always apply the parking brake when working on a vehicle.
Chock the front and rear tires to prevent unexpected vehicle movement.
If working without a lift, always consult vehicle manual for correct lifting
specifications.
Operate the engine only in well-ventilated areas to avoid exposure to carbon
monoxide.
Do not smoke or use flammable items near or around the fuel system.
Use chemicals and cleaners in well-ventilated areas.
Batteries produce explosive gases, which can cause personal injury.
Therefore, do not allow flames, sparks or flammable substances to come near
the battery.
Keeps hands and any other objects away from the radiator fan blades.
Keep yourself and your clothing away from moving parts when the engine is
running.
Do not wear loose clothing or jewelry that can get caught in rotating parts or
scratch surface finishes.
Allow the engine, cooling system, brakes and exhaust to cool before working
on a vehicle.
WORK SAFELY!
Perform this installation on a good clean level surface for maximum safety and
with the engine turned off.
1310R08030006IM
Page 3 of 9
1-800-59-ROUSH
®
1. Open the trunk and remove thirteen (13) push pins indicated with circles. Refer
to Figure 1. The push pins are a two (2) part push pin. Remove the center
button first to release the barbs and then remove the push pin body. Carefully
slide the glow-in-the-dark trunk release handle through the slot in the trunk liner.
See arrow. Remove the trunk inner liner.
Figure 1
2. Vehicles equipped with a satellite antenna,
remove the connector push pin from the holes
in the trunk inner structure. With a small screw
driver, remove the push pin retainer from the
connector. Refer to Figure 2. Push the release
tab and unplug the connectors.
Figure 2
1310R08030006IM
Page 4 of 9
1-800-59-ROUSH
®
3. Retrieve the Bracket Positioning Template from the kit. Fold the template on the
dotted line. Align the shaded holes on the template to the corresponding holes
on the trunk lid inner structure. Tape the template in place. Refer to Figures 3.
Figures 3
4. Center punch the top four (4)
bracket mounting points as
shown on the template.
Refer to Figure 4. Remove
the paper template.
Figure 4
Note: Before installing the Self-drilling Screws, set your drill to a light setting to
avoid stripping the holes or breaking the screws.
5. Position the Left Side Bracket to the left two (2)
center punch points. Install the top two (2)
Self-drilling Screws to secure the Bracket top to
the deck lid inner structure. Refer to Figure 5.
Figure 5
1310R08030006IM
Page 5 of 9
1-800-59-ROUSH
®
6. Gently pull the lower part of the mounting bracket rearward (3-4 mm) and place
a plastic Adapter Bracket into the slot. Ensure that the nut is on the back side of
the bracket. Refer to Figures 6. Install a Self-drilling Screw through the bottom
hole of the bracket into the trunk inner structure.
Figures 6
7. Repeat Steps 5 for the right side bracket. ( Top two (2) screws only )
8. Pass the wire harness end of the
satellite antenna connector behind
the right mounting bracket and
reconnect the connectors. Peel the
backing tape from the Double Sided
Tape and affix the connector to the
trunk inner structure as shown.
Refer to Figure 7.
Note: Do not put the connector into its
original position. Installation of the tool
box will crush the connector.
Figure 7
9. Repeat Steps 6 for the right side bracket. ( Adapter Bracket and bottom screw )
10. Torque the six (6) Screws to 20-22 In-Lb.
1310R08030006IM
Page 6 of 9
1-800-59-ROUSH
®
11. Retrieve the Deck Lid Liner Cutting Template from the kit. Cut out the three (3)
sections shown on the template. Position the Deck Lid Liner Cutting Template
onto the deck lid liner with the raised portions of the liner in the template cut
outs. Refer to Figure 8. Cut out the two (2) 1/2” square holes in the deck lid
liner as indicated on the template. Remove the cutting template.
Figure 8
12. Reinstall the trunk inner
liner and 13 push pins.
Ensure that you pass the
glow-in-the-dark trunk
release handle through
the slot in the trunk liner.
Refer to Figure 9 and
Figure 1. Ensure the 1/2”
holes in the liner expose
the Adapter Bracket nuts.
Figure 9
1310R08030006IM
Page 7 of 9
1-800-59-ROUSH
®
13. Open the Tool Kit and remove the ROUSH mechanics gloves. With an assistant,
raise the opened ROUSH Tool Box to align the slots in the Tool Box Lid to the
nuts in the plastic Adapter Brackets. Install the two (2) Washers and Bolts to
fasten the Tool Box Lid to the Plastic Adapter Brackets. Refer to Figure 10.
Figure 10
14. Replace the ROUSH Mechanics Gloves back into the tool kit. Close and latch the
ROUSH Tool Kit.
Congratulations!!! You have completed the installation of the ROUSH Performance
Products, Trunk Mounted Tool Kit. It is recommended that you save all parts removed
from your vehicle during the installation of this kit.
1310R08030006IM
Page 8 of 9
1-800-59-ROUSH
®
WARRANTY
All retail parts carry a 90-day warranty from the date of purchase. This warranty covers
defects in materials or workmanship, and does not include (i) normal wear and tear,
environmental conditions, improper installation; (ii) road hazards, misuse, abuse,
neglect, accidents, collision, fire, theft, freezing, vandalism, riot, explosion, or objects
striking the vehicle; (iii) misusing the vehicle, such as driving over curbs, overloading,
racing, or using the vehicle as a stationary power source; (iv) altering, disassembling or
modifying the parts; (v) defects caused or induced by failures, breakdowns, or damage
by other parts, components or the vehicle; (vi) subjecting the parts to excessive
moisture or water or any motor vehicle fluids (e.g.: oil, anti-freeze, battery acid, brake
fluid, etc.); (vii) acts of God, natural disasters and other similar causes beyond the
reasonable control of ROUSH; or (viii) application of chemicals that affect the parts.
This Limited Warranty does not cover surface deterioration of paint, trim, and
appearance items that result from use and/or exposure to the elements, such as stone
chips, scratches, bird droppings, lightning, hail, windstorm, dings, dents, earthquake,
road salt, tree sap, water or flood.
ROUSH SHALL NOT BE LIABLE TO REIMBURSE CUSTOMER/DEALER FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES RESULTING FROM THE INSTALLATION OR USE OF
ANY PRODUCT SOLD THROUGH THIS CATALOG OR ARISING OUT OF ANY BREACH OF
WARRANTY. EXCEPT AS MAY BE STATED IN THIS CATALOG, ROUSH DISCLAIMS ALL
EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL
ROUSH’S LIABILITY EXCEED THE PRICE PAID BY CUSTOMER/DEALER FOR PRODUCTS
SOLD REGARDLESS IF ROUSH HAS BEEN ADVISED IN ADVANCE OF ANY POTENTIAL
PROBLEM OR IF A CLAIM IS BASED ON CONTRACT, TORT, STRICT LIABILITY,
PRODUCT LIABILITY OR OTHERWISE. SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF IMPLIED WARRANTIES OR THEIR DURATION, OR LIABILITY FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSIONS OR
LIMITATIONS MAY NOT APPLY.
1310R08030006IM
Page 9 of 9
1-800-59-ROUSH
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement