CleanCraft SuperLite CSL160XL Instruction manual

CleanCraft SuperLite CSL160XL Instruction manual

CleanCraft CSL160XL is a lightweight yet powerful vacuum system ideal for commercial use on all types of carpets and floors. With its dual suction system and twin fan/dual suction design, it delivers deeply embedded dirt and superior edge cleaning. It features a 50-foot heavy-duty, commercial-quality power cord for extended reach and a 6-amp motor for full cleaning power while saving energy. Other features include a rotating cleaning brush with white, non-marring bristles, non-marring wheels for safe use on bare floors, and a soft furniture protection guard to prevent damage while vacuuming.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

CleanCraft SuperLite CSL160XL Instruction manual | Manualzz

CleanCraft SuperLite 160XL

Dual Suction Upright Vacuum System

Instruction Manual

Model: CSL160XL

CleanCraft Limited Warranty

CleanCraft will repair or exchange parts for your vacuum in the event of a manufacturing defect as follows:

Parts: New or comparable rebuilt parts, for one year after original purchase.

Labor: Carry-in service can be obtained during the warranty period by taking or shipping your vacuum to an Authorized CleanCraft Warranty Service Center. (Note: Shipping cost is the responsibility of the customer).

Important Warranty Conditions: A purchase receipt or other proof of date of original consumer purchase also will be required before warranty service is rendered.

This warranty covers normal use and does not cover damage which occurs in shipment or failure resulting from alteration, accident, misuse, abuse, neglect, or improper maintenance.

Statement: This warranty is not transferable and extends only to the original purchaser when a new CleanCraft vacuum is purchased from an

Authorized CleanCraft Dealer. This warranty gives you specific legal rights, and you may have other rights that vary from state to state.

CleanCraft Products, Inc.

800-525-3261 www.cleancraft.com

MN-CSL160XL-01

I

MPORTANT

S

AFETY

I

NSTRUCTIONS

G

ROUNDING

I

NSTRUCTIONS

When using an electrical appliance, basic precautions should be observed, including the following: Read all instructions before using your lightweight upright vacuum cleaner.

WARNING: To reduce the risk of fire, injury or electric shock:

• Never leave cleaner unattended when it is plugged in.

• Unplug from outlet when not in use and before servicing.

• Never use with damaged cord or plug.

• Never unplug by pulling on cord.

• Never pull or carry by cord, use cord as a handle, close door on cord, pull cord around sharp corners, run cleaner over cord, or expose cord to heated surfaces.

• Never use cleaner if it has been dropped, damaged, left outdoors or dropped into water. Return it to place of purchase.

• Never allow children to use as a toy.

• Never use outdoors or on wet surfaces.

• Never handle cleaner or plug with wet hands.

• Never put any object into openings, use with blocked opening, or restrict air flow.

• Never use without dust bag and/or filters in place.

• Never allow hair, loose clothing, fingers or body parts to get near openings or floor brush in the appliance.

• Never pick up hot coals, cigarette butts, matches or any hot, smoking, or burning objects.

• Never pick up hard or sharp objects such as glass, nails, screws, coins, etc.

• Never pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in the presence of explosive liquids or vapor.

• Connect to a properly grounded outlet only.

See grounding instructions.

• Never pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).

• Never use in an enclosed space filled with vapors given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapors.

• Never use for any purpose other than described in this

User’s Guide.

• Use only on dry, indoor surfaces.

• Keep openings free of dust, lint, hair, etc.

• Keep appliance on a level surface.

• Turn off all controls before plugging in or unplugging cleaner.

• Be extra careful when cleaning stairs.

• Pay close attention when working around children.

This appliance must be connected to a grounded wiring system.

If it should malfunction or break down, grounding provides a safe path of least resistance for electrical current, reducing the risk of electrical shock. The cord for this appliance has an equipmentgrounding conductor and a grounding plug. It must only be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or service person if you aren’t sure if the outlet is properly grounded. NEVER MODIFY THE PLUG. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is designed for use on a nominal 120-volt circuit, and has a grounding attachment plug that looks like the plug in the drawing above. Make certain that the appliance is connected to an outlet having the same configuration as the plug.

No plug adapter should be used with this appliance.

P

Grounded

Outlet

Prong or

Grounding pin

RODUCT

F

Grounded

Outlet Box

EATURES AND

B

ENEFITS

The Dual Suction System is a lightweight, yet powerful, cleaning system ideal for commercial use on all types of carpets and floors.

1.

Handle – designed for comfort and easy maneuvering.

2.

Power Switch – conveniently located in handle.

3.

Handle Tube – lightweight, for easy movement and use.

4.

Connector Tube – strong lightweight aluminum tube is designed for optimal airflow.

5.

Dust Tube – large diameter dust tube designed to minimize clogging.

6.

Cloth Bag – durable, reinforced material for years of service.

7.

Dust Bag – top loading bag for clean and easy bag change.

8.

The Post-Motor Filter – helps to reduce motor emissions.

9.

Motor – 6 amps of full cleaning power, saves energy.

10. Power Source Plug – grounded for safe, reliable operation.

11. Connector Plug – for enhanced safety.

12. Power Cord – 50 foot heavy-duty, commercial quality for extended reach.

SAVE THESE INSTRUCTIONS

P

RODUCT

F

EATURES AND

B

ENEFITS

13. Quick Release Cord Hooks – for quick, easy removal of power cord.

14. Powerfoot – twin fan/dual suction design for deeply embedded dirt and superior edge cleaning.

15. Rotating Cleaning Brush – continuous, rotating dual action for thorough cleaning; white, non-marring bristles.

16. Non-Marring Wheels – safe for use on bare floors.

17. Soft Furniture Protection Guard – helps protect furniture while vacuuming.

18. Hair Cutter – ensures that any long hair or other fibers are cut and broken down into lengths that are manageable for the vacuum. This helps to prevent clogs.

19. Filter Cover – easily removes with one screw for easy access to filter.

20. Dual Cord Storage – wrap cord around the back of the unit, or simply hang cord on the front Cord Storage Hook.

21. Tube Release Buttons – allows for easy access in the unlikely event of the tube clogging.

22. Bag Tension Spring – keeps the bag secure at the base of the bag.

23. Rubber Collars – designed to seal air path at critical connections, preventing loss of airflow.

24. Top Cover – simply removes with 3 screws allowing for easy belt change.

25. Drive Belt – designed for optimal life and performance.

H

OW

T

O

A

SSEMBLE

WARNING: Plastic bags or film can be dangerous. To avoid danger of suffocation, keep away from babies and children.

The dual Suction System is packaged for convenience and requires minimal assembly.

The only tool you will need is a Phillips head screwdriver.

1. Slide the handle Tube into the Connector, aligning the hole in the Handle Tube with the molded hole at the top of the Connector.

2. Hold the hex nut in front of the Connector in the hex shaped cavity while inserting the screw with your finger from the back. Tighten the screw while placing your finger over the hex cavity to hold the hex nut in place. After a few turns, tighten further with a

Phillips head screwdriver. Do not overtighten.

3. Slide screw through plastic Cord Hook from the inside of Cloth Bag. Align screw with hole in Handle Tube. Tighten screw.

4. Remove screw from Filter Cover. Remove Filter Cover. Insert the Connector Plug into the back of the unit at the rear of the Powerfoot – Make sure the Connector Plug is fully inserted. Replace Filter Cover. Replace Filter Cover Screw.

Your Vacuum cleaner is now ready to use.

H

OW

T

O

U

SE

Y

OUR

D

UAL

S

UCTION

S

YSTEM

V

ACUUM

Tip. Before cleaning under low furniture, always check area first for objects that might harm the Rotating

Cleaning Brush or get caught in the Dust Tube.

Power Supply

The Power Cord is stored at the back of the vacuum cleaner, and is looped around the Quick Release Cord

Hooks. The polarized Power Source Plug is designed to attach to the Power Cord during storage. Before using, make sure the Connector Plug is securely attached to the Powerfoot and that the Power Source Plug is plugged into a polarized outlet.

Power Switch

The Power Switch is located in the Handle of the cleaner. Push down (I) to turn ON. Push up (O ) to turn

OFF.

Power Cord Storage

When you are finished using your vacuum, return it to the upright position. Make sure the vacuum is turned

OFF. Always unplug the vacuum by grasping the Power Source Plug (NOT the Power Cord) and disconnecting from the outlet. Properly store the Power Cord by winding the cord around the Quick Release Cord Hooks on the back of the vacuum in a continuous loop, or by hanging the cord on the Cord Storage Hook located on the front of the vacuum. Attach the Power Source Plug to the Power Cord.

Operation

This vacuum, with Dual Suction System is designed to effectively and safely clean all types of carpeting, wood, linoleum, and vinyl floors. Its wide 14-inch Powerfoot makes cleaning quick and easy.

To place the vacuum in position for use, lightly press your foot on the Powerfoot and tip the Handle backwards.

H

OW

T

O

U

SE

Y

OUR

D

UAL

S

UCTION

S

YSTEM

V

ACUUM

Routine Maintenance

For maximum performance from your vacuum, check and maintain vacuum parts regularly.

Replacing the Dust Bag

Check the Dust Bag weekly. Replace the Dust Bag when it is near full or when cleaning suction diminishes. Never reuse a Dust Bag.

WARNING: To avoid electrical shock or injury from moving parts, always turn OFF the Power Switch and unplug the Power Source Plug before performing maintenance or trouble shooting. Always unplug by grasping the Power Source Plug; NEVER pulling on the Power Cord to unplug.

Tip: Vacuuming new carpet or vacuuming fine powders may clog the Dust Bag.

Check Dust bag often.

Unplug vacuum by grasping and pulling on the Power Source Plug.

Unzip Cloth Bag. Remove collar retainer by pressing on the two tabs and pulling the top towards you. Dispose of Dust Bag.

Slide collar of new Dust Bag completely into collar retainer.

Push collar retainer back into position and secure in place.

Tuck the remainder of the Dust Bag completely inside the Cloth Bag. Make sure it lays flat, top to bottom, without bunching. Zip Cloth Bag.

Cleaning the Dust Tube

The vacuum features Dust Tube designed to optimize cleaning power. For best performance, routinely check and clear excess dust and other debris.

Note: Cover floor with newspaper to catch any loose material or dust removed during cleaning.

Release Bag Tension Spring.

Remove Filter Cover screw and then remove Filter Cover.

Unplug Connector Plug.

Locate the Tube Release Button at the top of the Powerfoot. The Tube Release

Button is hidden under a Rubber Collar on the side of the Dust Tube and can be pressed through the Rubber Collar. Lift off the Dust Tube while pressing on the Tube

Release Button.

Use a wire brush to clean out the inside of the Dust Tube and the top section of the

Powerfoot where they connect.

Reconnect the tube with the Powerfoot. It should snap into place. Make sure that the tube release button on the Tube lines up with the Tube Release Button on the

Rubber Collar.

Plug the Connector Plug back into base of vacuum.

WARNING: To avoid electrical shock or injury from moving parts, always turn OFF the Power Switch and unplug the Power Source Plug before performing maintenance or trouble shooting. Always unplug by grasping the Power Source Plug; NEVER pulling on the Power Cord to unplug.

H

OW

T

O

U

SE

Y

OUR

D

UAL

S

UCTION

S

YSTEM

V

ACUUM

Cleaning the Filter

The Post-Motor Filter is located in the Powerfoot of your vacuum cleaner. It should be checked often, and cleaned when the Post-Motor Filter becomes dirty.

1.To Clean Post-Motor Filter, remove the screw with a Phillips head screwdriver.

2.Lift out Filter Cover.

3.Remove Post-Motor-Filter and wash with mild soap and water. Dry thoroughly.

4.Reinstall clean and dried Post-Motor filter.

5.Replace Filter Cover by sliding in the two tabs at the top of the Filter Cover and centering over the screw hole.

6. Replace screw.

Cleaning the Rotating Cleaning

Brush/Replacing the Drive Belt

Check the Rotating Cleaning Brush and Drive Belt regularly for wear or damage. Keep the

Rotating Cleaning Brush ends free of string, hair, and carpet fibers. These can become entangled and reduce the vacuum’s cleaning effectiveness.

NOTE: The Rotating Cleaning Brush can most often be cleaned without removal from the vacuum. If there is an excessive amount of hair and debris, remove the Rotating Cleaning

Brush for proper cleaning.

1.Unplug the vacuum and turn face down on a flat surface.

2.Remove all 3 screws from the bottom of the Powerfoot.

3.Grip both the Top Cover and base while turning unit back over. Lift off Top Cover.

4.Check Drive Belt. If it is broken or damaged, remove Rotating Cleaning Brush and replace Drive Belt.

WARNING: To avoid electrical shock or injury from moving parts, always turn OFF the

Power Switch and unplug the Power Source Plug before performing maintenance or trouble shooting. Always unplug by grasping the Power Source Plug; NEVER pulling on the Power

Cord to unplug.

5.To remove the Rotating Cleaning Brush, pull the right side of the Rotating Cleaning

Brush toward the front of the Powerfoot as you lift slowly.

6.Clean off Rotating Cleaning Brush as necessary.

7.Place existing or new Drive Belt over Rotating Cleaning Brush and the motor shaft. Insert the end cap pin on the left of the Rotating Cleaning Brush into the slot on the Powerfoot and slide the end cap pin on the right end of the Rotating Cleaning Brush in to the slot in the Powerfoot and lower until it clicks into place.

8.Make sure the Furniture Protection Guard is still intact.

9.Align the 3 tabs on the Top Cover with the 3 slots in the Powerfoot. Press into place, making sure the Furniture Protection Guard is on the outside.

10. Turn vacuum cleaner face down.

11. Reinstall the 3 screws beginning with the center screw.

WARNING: To avoid electrical shock or injury from moving parts, always turn OFF the Power Switch and unplug the Power Source Plug before performing maintenance or trouble shooting. Always unplug by grasping the Power Source Plug;

NEVER pulling on the Power Cord to unplug.

T

ROUBLESHOOTING

Vacuum cleaner won’t run.

Possible Causes

Vacuum Cleaner is not plugged in

Household fuse/circuit breaker tripped

Vacuum cleaner won’t pick up dirt.

Possible Causes

Dust Bag is full

Drive Belt not functioning

Rotating Cleaning Brush bristles worn

Rotating Cleaning Brush jammed

Dust Tube is clogged

Remedies

Check power Source Plug and Connector Plug

Check/replace fuse – Reset breaker

Remedies

Replace with new Dust Bag

Realign Drive Belt or replace if damaged

Replace Rotating Cleaning Brush

Remove Rotating Cleaning Brush and clean debris from brush ends; Reinstall Drive Belt

Clean Dust Tube

Accumulation of dust inside Cloth Bag

Possible Cause

Dust Bag is clogged or dirty

Dust Bag collar retainer not secure

Inlet clogged

Remedies

Replace with new Dust Bag

Secure Dust Bag collar retainer

Shake dust down to bottom of Dust Bag.

P ARTS ref#

13

14

15

16

9

10

11

12

17

18

19

20

21

7

8

5

6

3

4

1

2 part #

C431-4400

B431-4814

A428-2014

B431-4914 description

Handle Assembly

Upper Cord Hook

Main Switch Handle

Cord Hook Commercial

A090-0200 Screw

D431-4300 Upper Duct Diverter & Bag Mount Assembly

B211-4414

D431-0600

Bag Mount Foam Gasket

Zippered Cloth Bag Assembly

B014-0814 Belt

B016-1400 Upright Stop w/Spring Clips

B015-2414 Squeege

PFSM-CFR62EC 09.06

ref# part # description

22 B010-0900 Small

23 B016-1314 Basetray

24 B014-0000 Belt Guard Hair Cutter

25 B016-0600 Left Pivot

26 B016-0400 Right

27 B018-0239 Lens

28 B051-0639 Lense Holder Cover

29 B051-0514 Motor

30

31 D051-0000 Motor Assembly

32 D051-0400 Assembly

33 B431-4114 Lower Cord Clip/Yoke Support

34 A028-0214 Male

35 B051-0239 Post

36 B051-0114 Post Filter Cover

37 A434-0831 Cord

38 A732-8314 Screw

39 A732-8414 Screw

40 A090-0300 Screw

41 A090-0400 Screw

42 A090-0500 Nylon

©CFR, All Rights Reserved

Ref # Part # Description

1 SL-C431-4400 Handle Assembly

2 SL-B431-4814 Upper Cord Hook

3 SL-A428-2014 Main Switch Handle

4 SL-B431-4914 Cord Hook Commercial

5 SL-B431-4700 Handle Tube Rectangular

6 SL-A090-0200 Screw

7 SL-A090-0100 Cable Clamp

8 SL-D431-4300 Upper Duct Diverter & Bag Mount Assembly

9 SL-B431-4214 Rubber Collar

10 SL-B211-4414 Bag Mount Foam Gasket

11 SL-D431-0600 Zippered Cloth Bag Assembly

12 SL-B431-4000 Duct Tube

13 SL-B014-0814 Belt

14 SL-B016-1400 Upright Stop w/Spring Clips

15 SL-B017-3639 Nozzle Cover

16 SL-B206-7900 Nozzle Label

17 SL-D017-3600 Nozzle Cover Assembly

18 SL-B029-0414 Furniture Guard

19 SL-B012-3000 Agitator Assembly

20 SL-B015-2414 Squeege

21 SL-B010-1414 Small Wheel

22 SL-B010-0900 Small Axle

23 SL-B016-1314 Basetray

24 SL-B014-0000 Belt Guard Hair Cutter

25 SL-B016-0600 Left Pivot

26 SL-B016-0400 Right Pivot

27 SL-B018-0239 Lens

28 SL-B051-0639 Lense Holder Cover

29 SL-B051-0514 Motor Cover

30 SL-D113-3200 Motor Assembly

31 SL-D051-0000 Motor Housing Assembly

32 SL-D051-0400 Duct Cover Assembly

33 SL-B431-4114 Lower Cord Clip/Yoke Support

34 SL-A028-0214 Male Plug

35 SL-B051-0239 Post Filter

36 SL-B051-0114 Post Filter Cover

37 SL-A434-0831 Cord Set

38 SL-A732-8314 Screw

39 SL-A732-8414 Screw

40 SL-A090-0300 Screw

41 SL-A090-0400 Screw

42 SL-A090-0500 Nylon Insert

advertisement

Frequently Answers and Questions

What is special about CleanCraft CSL160XL?
It's a Dual Suction Upright Vacuum System designed for commercial use; ideal for all types of carpets and floors.
Warranty?
Parts: New or comparable rebuilt parts for one year after original purchase. Labor: Carry-in service during the warranty period.
How to assemble it?
1. Slide the handle Tube into the Connector. 2. Hold the hex nut and insert screw using finger from the back. Tighten the screw with a screwdriver. 3. Slide screw through plastic Cord Hook and align with hole in Handle Tube. Tighten screw. 4. Insert Connector Plug into rear of unit. Replace Filter Cover and screw.
How to use the vacuum?
1. Plug in the Power Source Plug. 2. Push the Power Switch down to turn ON. 3. Lightly press your foot on the Powerfoot and tip the Handle backwards.
How to replace the Dust Bag?
1. Unplug the vacuum. 2. Unzip Cloth Bag. 3. Remove and discard the full Dust Bag. 4. Insert a new Dust Bag. 5. Zip up the Cloth Bag.

Related manuals

Download PDF

advertisement