42004-658L2G
Pub. 42004-658L2G
GAI-TRONICS® CORPORATION
A HUBBELL COMPANY
701-902 SmartSeries®
Handset/Speaker Amplifier
TABLE
OF
CONTENTS
Confidentiality Notice .....................................................................................................................1 General Information .......................................................................................................................1 Product Overview ................................................................................................................................... 1 System Requirements and Limitations ................................................................................................. 1 Features and Functions .......................................................................................................................... 1 Description of Major Components ........................................................................................................ 2 External Components ............................................................................................................................................ 2 Internal Components ............................................................................................................................................. 3 Block Diagram......................................................................................................................................... 4 Interfaces ................................................................................................................................................. 5 Installation ......................................................................................................................................5 Operation .........................................................................................................................................6 Page Announcement ............................................................................................................................... 6 Party-Line Conversation ........................................................................................................................ 6 Optional Features.................................................................................................................................... 7 Maintenance ....................................................................................................................................7 Adjustments ............................................................................................................................................. 8 Minimum Level Adjustment ................................................................................................................................. 8 Offset Level Adjustment ....................................................................................................................................... 8 VLC Level Adjustment ......................................................................................................................................... 8 Internal Adjustments .............................................................................................................................. 9 Sidetone Volume and Handset Receiver Volume ................................................................................................. 9 Troubleshooting .................................................................................................................................... 10 How to Diagnose Assembly Faults....................................................................................................... 11 Specifications ................................................................................................................................13 Replacement Parts ................................................................................................................................ 14 GAI-Tronics Corporation 400 E. Wyomissing Ave. Mohnton, PA 19540 USA
610-777-1374  800-492-1212  Fax: 610-796-5954
VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
PUB. 42004-658L2G
GAI-TRONICS® CORPORATION
A HUBBELL COMPANY
701-902 SmartSeries®
Handset/Speaker Amplifier
Confidentiality Notice
This manual is provided solely as an operational, installation, and maintenance guide and contains
sensitive business and technical information that is confidential and proprietary to GAI-Tronics.
GAI-Tronics retains all intellectual property and other rights in or to the information contained herein,
and such information may only be used in connection with the operation of your GAI-Tronics product or
system. This manual may not be disclosed in any form, in whole or in part, directly or indirectly, to any
third party.
General Information
Product Overview
The 701-902 SmartSeries® Handset/Speaker Amplifier provides the following features:

Supports one-way page announcements over system speakers.

Serves as an amplifier to broadcast page announcements over the station’s speaker.

Supports party-line (two-way) communication with other system users.

Serves as a control interface to optional devices such as the remote terminal unit (RTU) when
installed into a SmartSeries® RTU enclosure.
System Requirements and Limitations
The 701-902 SmartSeries® Handset/Speaker Amplifier is designed to provide an intelligent handset for
use on the GAI-Tronics system cable in either a standard Page/Party® system or an ADVANCE system.
Features and Functions

Provides page and party line
communications from the integral handset.

Supports an optional SmartSeries® station RTU that
monitors and supervises input and output devices

Measures the ambient noise and adjust the
speaker output level accordingly.

Supports an optional party line End-of-Line
module, which supervises party line 1.

Monitors and controls the handset


Transfers data messages and audio on the system
cable.
Supervises the local speaker.
GAI-Tronics Corporation 400 E. Wyomissing Ave. Mohnton, PA 19540 USA
610-777-1374  800-492-1212  Fax: 610-796-5954
VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
®
701-902 SMARTSERIES HANDSET/SPEAKER AMPLIFIER
Pub. 42004-658L2G
PAGE 2 of 14
Description of Major Components
The 701-902 Handset/Speaker Amplifier includes external components accessible to the user as well as
internal components or subassemblies.
External Components
As shown from the front in Figure 1, this assembly includes a handset and cradle. When the handset is
lifted from the cradle or replaced in the cradle, a hookswitch (a magnetic reed switch) in the cradle signals
the appropriate status to the microcontroller within the assembly.
To the right of the cradle, the GAI-Tronics nameplate conceals the User Level Adjustment control.
Figure 1. Front View
f:\standard ioms - current release\42004 instr. manuals\42004-658l2g.doc
03/12
®
701-902 SMARTSERIES HANDSET/SPEAKER AMPLIFIER
Pub. 42004-658L2G
PAGE 3 of 14
Internal Components
As shown from the side in Figure 2, the assembly contains the following components or subassemblies:

Chassis

Front panel affixed to the front of the chassis

Handset Amp/FSK/P PCBA (printed circuit board assembly) (Ref. 14) affixed to the rear of the
front panel

Speaker Amp/Power Supply PCBA (Ref. 13) affixed to the rear of the chassis, with a plug (P1) at the
top, pointing to the rear
Figure 2. Side View
f:\standard ioms - current release\42004 instr. manuals\42004-658l2g.doc
03/12
®
701-902 SMARTSERIES HANDSET/SPEAKER AMPLIFIER
Pub. 42004-658L2G
PAGE 4 of 14
Block Diagram
The P1 connector on the back of the Speaker Amp/Power Supply PCBA plugs into a socket in an
enclosure connected to the system cable, accessing the Page/Party® lines and ac power. The Speaker
Amp/Power Supply PCBA contains the low voltage power supplies and the speaker amplifier circuitry.
Connector J1A and J1B on the Speaker Amp/Power Supply connects regulated +5 V dc, +/−15 V dc, and
VRLY voltages along with control, monitoring, and line signals to the J1A and J1B on the Handset
Amp/FSK/P PCBA. Connector J2 of the Speaker Amp/Power Supply PCBA connects to optional
external devices.
The Handset Amp/FSK/P PCBA has connections to the handset and the hookswitch via spade terminal
connectors E1 to E7.
Figure 3. Block Diagram
f:\standard ioms - current release\42004 instr. manuals\42004-658l2g.doc
03/12
®
701-902 SMARTSERIES HANDSET/SPEAKER AMPLIFIER
Pub. 42004-658L2G
PAGE 5 of 14
Interfaces
The assembly interfaces to the system cable an external loudspeaker and auxiliary devices via P1, a 16pin connector. All connections to the system cable are made by qualified installation technicians during
the system installation.
Direct questions about these connections to the GAI-Tronics Field Service Department at 800-492-1212
inside the USA or 610-777-1374 outside the USA. Other connections on the Speaker Amp/Power Supply
PCBA provide quick connect/disconnect of subassemblies.
Connector J2 on the bottom of the Speaker Amp/Power Supply PCBA connects to optional devices such
as the SmartSeries® Remote Terminal Unit (RTU) installed in specially designed enclosures.
Installation
CAUTION
Do not install this equipment in hazardous areas other than those indicated
on the approval listing in the “Specifications” section of this manual. Such installation may cause a
safety hazard and consequent injury or property damage.
The 701-902 SmartSeries® Handset/Speaker Amplifier plugs directly into any standard GAI-Tronics 700
series enclosure. Use extra care not to damage the protruding latch wings of connector J2 located on the
bottom edge of the amplifier during installation.
It also plugs into standard SmartSeries enclosures such as a SmartSeries® station RTU enclosure, an
Emergency Party Line (EPL) enclosure, or an enclosure that houses a party line End-of-Line (EOL)
module. When installing the assembly in one of these enclosures, you must also connect the 10conductor keyed ribbon cable to J2 on the bottom of the Speaker Amp/Power Supply PCBA. Be sure
that the red line on the edge of the cable lines up with J2-pin 1.
Ensure that the connectors mate securely and then tighten the four screws in the corners of the front panel.
f:\standard ioms - current release\42004 instr. manuals\42004-658l2g.doc
03/12
®
701-902 SMARTSERIES HANDSET/SPEAKER AMPLIFIER
Pub. 42004-658L2G
PAGE 6 of 14
Operation
This section describes the operation of the 701-902 SmartSeries® Handset/Speaker Amplifier.
Note regarding the busy tone: A busy tone is heard in the receiver when either of the following occurs:


a page of a higher priority is in progress
a page is attempted within one second of a previous page
Page Announcement
To make a page announcement for a party-line conversation, perform the following steps:
1. Lift the handset from the cradle.
2. Select an available party line.
3. Press the handset pressbar.
4. Make your announcement when the wait tone stops. If the page resource is already in use, you hear a
busy tone. Release the handset pressbar, then try again.
5. Release the handset pressbar.
6. When the party answers conduct your conversation.
7. Replace the handset in the cradle at the end of the conversation.
Party-Line Conversation
To conduct a party-line conversation, perform the following steps:
1. If using a multi-party enclosure, first select the appropriate party line.
2. Lift the handset from the cradle.
3. Conduct your conversation.
4. Replace the handset in the cradle when the conversation is finished.
f:\standard ioms - current release\42004 instr. manuals\42004-658l2g.doc
03/12
®
701-902 SMARTSERIES HANDSET/SPEAKER AMPLIFIER
Pub. 42004-658L2G
PAGE 7 of 14
Optional Features
The following features are available as options to the standard configuration of a station used in an
ADVANCE system and installed in a standard SmartSeries or a custom enclosure. These features can be
configured. Contact the GAI-Tronics Field Service Department at 800-492-1212 inside the USA or 610777-1374 outside the USA for further information about these features.

The Selected Page Destination feature allows the manual selection of one of four page destinations.

The Supervised Input feature allows the monitoring and supervision of one or two initiating device
circuits (IDCs), initiating an alarm when the supervised device is activated.

The Power Relay Module provides a relay contact output, typically to switch power to a visual
signaling device, for directed or relay group operation. Supervision of the controlled device’s cable
can also be enabled.

The Station Emergency Party Line feature supports annunciation for two party lines.
Maintenance
Regular inspection and a good preventive maintenance program will increase the reliability of your
GAI-Tronics station. The GAI-Tronics Field Service Department can formulate a service contract suited
to your facility’s specific need for preventive maintenance.
If the equipment requires service, contact your Regional Service Center for a return authorization number
(RA#). Equipment should be shipped prepaid to GAI-Tronics with the return authorization number and a
purchase order number. If the equipment is under warranty, repairs will be made without charge. Please
include a written explanation of all defects to assist our technicians in their troubleshooting efforts. Call
800-492-1212 for help in identifying the Regional Service Center closest to you.
WARNING
Before performing any of the following preventive maintenance steps, remove
all power from the station.
1. Inspect and replace frayed or cracked wiring.
2. Secure/replace loose wires and spade terminals.
3. Remove corrosion from terminals.
There are three replaceable fuses (F1, F2, and F3) mounted on the Speaker Amp/Power Supply PCBA
(Figure 2).

Fuse F1 protects the low voltage power supply circuits. Replace with GAI-Tronics part number
51801-027.

Fuse F2 protects the current to the speaker amplifier. Replace with GAI-Tronics part number
51801-003.

Fuse F3 limits the amount of current to any external device connected to J2. Replace with
GAI-Tronics part number 51801-024.
f:\standard ioms - current release\42004 instr. manuals\42004-658l2g.doc
03/12
®
701-902 SMARTSERIES HANDSET/SPEAKER AMPLIFIER
Pub. 42004-658L2G
PAGE 8 of 14
Adjustments
The User Adjustment Control is located beneath the GAI-Tronics nameplate on the front panel. Refer to
Figure 1. It is used to make all user adjustments normally required for installation. Loosen the two
screws on the GAI-Tronics nameplate and rotate it counterclockwise to access the adjustment hole. Make
adjustments by inserting a 1/8-inch flat blade screwdriver through the access hole and into the
potentiometer located directly behind the hole.
The User Adjustment Control potentiometer can be used to make three separate adjustments:

Minimum speaker amplifier output level setting

Offset amplifier level (difference between the ambient noise and the amplifier output levels)

VLC (volume level control) adjustment (sets a preset speaker level to override the normal volume
control setting).
Minimum Level Adjustment
To set the minimum amplifier output level, insert the 1/8-inch flat blade screwdriver into the User
Adjustment Control and set it fully counterclockwise. Listen for a single beep from the speaker
indicating the speaker amplifier is in the Minimum Level Adjustment mode. A continuous tone should be
heard after the beep tone. (See note below).
This test tone is used as a reference to adjust the speaker amplifier output level to the desired volume.
Turn the adjustment pot clockwise for the desired output. The test tone automatically shuts off 5 seconds
after the last adjustment. The factory default setting for minimum level is 4.0 watts nominal.
NOTE: If the page line is in use immediately after the beep tone, the page signal should be used to make
the minimum level adjustment. If the page line is inactive following the beep tone, a continuous tone is
activated to make the minimum level adjustment. After the tone is activated, all page line activity is
ignored until completion of the adjustment.
Offset Level Adjustment
The Offset Level allows the output of the SmartVolume™ speaker amplifier to maintain a set difference
or “offset” between the ambient noise level and the speaker output level. Turn the User Adjustment
Control fully clockwise and listen for the two beep tones indicating that the station is in the Offset
Adjustment mode. A continuous tone should be heard from the station speaker. Turn the adjustment pot
counterclockwise to the desired output level.
NOTE: If the page line is in use immediately after the two beep tones are heard, the page signal should be
used to make the offset level adjustment. If the page line is inactive immediately following the beep
tones, a continuous tone is activated to make the minimum level adjustment. After the tone is activated,
all page line activity is ignored until completion of the adjustment.
VLC Level Adjustment
When activated, the VLC overrides the normal volume control setting allowing the amplifier level to
change to a preset level during an emergency page. The factory default setting for the VLC Level is 10%
of maximum power (nominally 1.2 watts).
NOTE: The system must be equipped with a SmartSeries® MCU (Master Control Unit) to activate the
VLC function.
f:\standard ioms - current release\42004 instr. manuals\42004-658l2g.doc
03/12
®
701-902 SMARTSERIES HANDSET/SPEAKER AMPLIFIER
Pub. 42004-658L2G
PAGE 9 of 14
To adjust the VLC Level:
1. Force the station into the VLC mode by having someone execute a page from a station programmed
by the MCU to activate the VLC function.
2. During the page, turn the User Adjustment Control fully counterclockwise, and listen for two beep
tones through the page speaker indicating the VLC Adjustment mode has been activated.
3. After the two beep tones, turn the User Adjustment Control to the desired speaker level using the live
paging signal to adjust the level. The station automatically exits the VLC Adjustment mode and
reverts to normal operation 5 seconds after the last pot adjustment.
Internal Adjustments
Although they typically require no adjustments, the following volume levels can be set internally:
Sidetone Volume and Handset Receiver Volume
To make an adjustment, remove the assembly from its enclosure and make a temporary connection
between the assembly and the enclosure. Refer to Figure 2 for the reference numbers and locations of the
adjustment controls. Turn a control clockwise to increase the volume or threshold; turn it
counterclockwise to decrease the volume or threshold. Use a small flat-blade screwdriver with an
insulated shaft to make adjustments.
To access the controls, perform the following steps:
1. Loosen the four screws that secure the front panel.
2. Remove the assembly from the enclosure. If the enclosure is equipped with an optional EOL Module
or SmartSeries® station RTU, be careful to not disconnect the ribbon cable on J2 of the Speaker
Amp/Power Supply PCBA.
3. Connect the assembly to the enclosure using a 10440-002 maintenance cable between P1 on the
assembly and J1 on the enclosure.
4. Locate and adjust the control on the appropriate PCBA.
5. When you are finished with the adjustment:
a) Disconnect the 10440-002 maintenance cable.
b) Insert the assembly into the enclosure.
c) Tighten the four screws.
Handset Receiver Volume
Use the control labeled RCVR VOL (Ref. 7, on the Handset/FSK/P PCBA) to adjust to the desired level
the handset receiver volume for voice signals from a party line.
Sidetone Volume
The control labeled SIDETONE (Ref. 4, on the Handset/FSK/P PCBA) adjusts the handset/headset
sidetone.
f:\standard ioms - current release\42004 instr. manuals\42004-658l2g.doc
03/12
Pub. 42004-658L2G
PAGE 10 of 14
®
701-902 SMARTSERIES HANDSET/SPEAKER AMPLIFIER
Troubleshooting
The following table lists some hints to aid technicians in troubleshooting.
Problem
Any problem with
station performance
Possible Solution
Remove the assembly from the enclosure and examine it carefully for obvious
faults such as unconnected plugs, loose connections where the wires from the
handset and hookswitch connect to the Handset/FSK/P PCBA, and so on.
Determine whether the fault is in the assembly, or in the system, by plugging
in a known good spare assembly (set to the same address as the assembly
removed). If the fault is in the assembly, remove it for repair.
NOTE: When replacing the assembly, perform the following steps:
1. Set the address on the new assembly to 0, 3.
2. Plug the assembly into the enclosure.
3. After about 10 seconds, remove the assembly. The station is now set up
to request a download of configuration variables from the MCU.
4. Set the unit to the correct address. Set the address to 0, 4 for conventional
Page/Party® operation or consult the ADVANCE system manual for
address assignment information.
5. Plug the assembly back into the enclosure. The station initiates a
configuration download request (ADVANCE systems only). The time
required to complete the download depends upon system configuration
and system activity, but several seconds is typical.
Speaker volume needs
adjustment
Use the USER ADJ control to adjust the Minimum Level, Offset Level, or
VLC Level (as appropriate). Refer to the “Adjustments” section on page 8.
Incoming handset
speech level needs
adjustment
Use the Rcvr Vol control to adjust the handset receiver volume. Refer to the
“Adjustments” section of this document.
Acoustic feedback or
speech distortion
during page or party
operation
or
The user hears himself
when speaking

If the problem affects all stations, the line may not be terminated
correctly, may have loose connections, or a short to ground. Line balance
connections are critical.

If the problem affects only this assembly, the problem may be with its
sidetone setting. Contact the GAI-Tronics Field Service Department.
Feedback during page
only

Check within the enclosure for a purple wire on terminal 7: this is the
default setting for local speaker mute. If the wire is on terminal 8, then
the speaker is unmuted and may be causing feedback. Connect the wire
to terminal 7.

An adjacent speaker could be causing feedback. If an adjacent speaker is
the source of the feedback, adjust the orientation of the speaker so that it
is not aimed directly at the station. As a last resort, enable the mutual
muting function of the station. This is done by interconnecting terminal 7
of the two stations with the spare orange wire in the system cable (if this
wire is available).
Crosstalk
Likely to be external to the assembly and related to system cable faults.
f:\standard ioms - current release\42004 instr. manuals\42004-658l2g.doc
03/12
Pub. 42004-658L2G
PAGE 11 of 14
®
701-902 SMARTSERIES HANDSET/SPEAKER AMPLIFIER
How to Diagnose Assembly Faults
When the assembly is in an ADVANCE system that includes a vacuum fluorescent display (VFD), faults
may be automatically detected, transmitted to the MCU in data messages, and displayed or printed. Fault
messages and possible solutions for their causes are described in the table below.
Fault Message
Watch-Dog timer
Processor has Reset
xd times
(Where x is the
decimal number of
times the watchdog
timer has reset the
processor.)
Stuck Contact on
Polled Device
Paging Pressbar
Depressed
Cause and Effect
Possible Solution

Verify that the reset pins
2 and 3 (J2) on the
Handset/FSK/P PCBA
are not shorted.

Replace the
Handset/FSK/P PCBA.
Cause—The station has been in page mode
longer than the configured page limit.

Effect—Station page is cut off. When the
pressbar is released, a restore message is sent
to the MCU. The station then resumes normal
operation.

Verify that the handset
pressbar is not stuck.
Replace the
Handset/FSK/P PCBA.
Replace the Speaker
Amp/Power Supply
PCBA.
Cause—The watchdog timer has forced the
processor to reset. This occurs when the reset
pins (J2) on the Handset/FSK/P PCBA are
temporarily shorted or when the watchdog
timer does not receive regular status pulses
from U4 on the Handset/FSK/P PCBA.
Effect—The processor maintains a count of
the number of resets. If the station is powered
down, the count restarts at zero. The station
still amplifies incoming pages. For the fourth
and subsequent resets, the count is zero.

Stuck Contact on
Polled Device
Cause—The station has been in the off-hook
state longer than the configured time limit.


Handset Off-hook
Effect—Station handset operation is cut off.
When the station is returned to the on-hook
state, a restore message is sent to the MCU.
The station then resumes normal operation.

Verify that the handset is
not off-hook.
Replace the
Handset/FSK/P PCBA,
or cradle.
Replace the Speaker
Amp/Power Supply
PCBA.
Supervised Audio
Path
Cause—The station failed its internal health
check of the Handset/FSK/P PCBA.


Handset
Effect—The station disables the handset
amplifier health-check function after the first
failure.
Supervised Audio
Path
Cause—The station failed its internal speaker
amplifier health check.
Replace the Speaker
Amp/Power Supply PCBA.
Page Amp
Effect—The station disables the speaker
amplifier health-check function after the first
failure.
f:\standard ioms - current release\42004 instr. manuals\42004-658l2g.doc
03/12
Replace the
Handset/FSK/P PCBA.
Replace the Speaker
Amp/Power Supply
PCBA.
Pub. 42004-658L2G
PAGE 12 of 14
®
701-902 SMARTSERIES HANDSET/SPEAKER AMPLIFIER
Fault Message
Supervised Audio
Path
Speaker Voice Coil
Cause and Effect
Cause—The station is detecting no ambient
noise at the speaker or is detecting an ambient
noise lower than the configured failure
threshold. This may occur if there is a fault in
the speaker wire or a fault at the voice coil.
This also may occur if the ambient noise at
the speaker is too low, as is the case in a quiet
room.
Effect—The station continues measuring
speaker ambient noise. When acceptable
noise levels are subsequently measured, a
restore message is sent to the MCU.
Polled device
Cause—This message is output by the MCU
when it loses communication with the station.
This may occur if there is a fault in the page
line, if the station is powered-down, or if there
is some fatal malfunction within the station.
Effect—The MCU continues to attempt
communication with the station. When
communication is resumed, a restore message
is sent to the MCU.
Polled End-of-line
device
Cause—This message is the same as the
“Polled device” fault, except that the affected
station has been defined as an end-of-line
station in the MCU configuration.
Effect—When this fault occurs, the red EOL
FLT LED on the PPI bezel lights. When
communication is resumed, the LED
extinguishes and a restore message is sent to
the MCU.
f:\standard ioms - current release\42004 instr. manuals\42004-658l2g.doc
03/12
Possible Solution



Verify that the speaker
wire is connected and
intact.
Verify that the voice coil
is connected and intact.
Replace the Speaker
Amp/Power Supply
PCBA.

Replace Handset/FSK/P
PCBA.

Verify that the page line
is connected and intact.

Verify that the station is
installed correctly.

Replace the
Handset/FSK/P PCBA.

Verify that the page line
is connected and intact.

Verify that the station is
installed correctly.

Replace the station
assembly.
®
701-902 SMARTSERIES HANDSET/SPEAKER AMPLIFIER
Pub. 42004-658L2G
PAGE 13 of 14
Specifications
Electrical
Supply voltage .......................................................................... 90–140 V ac (120 V ac nominal), 50/60 Hz
Power consumed @ nominal ac ........... Zero/maximum signal (12 watts): 15 VA, 9 watts/59 VA, 32 watts
Speaker Amplifier
Output ............................................................................... 12 watts minimum, with nominal supply voltage
Frequency response.......................................................................... 350–6,500 Hz, +0/−3 dB, ref. to 1 kHz
Distortion ......................................................................................... 1% maximum THD @ 1 kHz, 12 watts
SmartVolume™
Monitor range (low gain) ...................................................................................................... 62–100 dB SPL
Offset (above ambient) user level adjustment................................................................................... 0–48 dB
Minimum user level adjustment ................................................................................. Off; 85 to 125 dB SPL
Handset Amplifier
Output ................................................................................................... 1.5 VRMS nominal into 33-ohm load
Frequency response with 5 mVRMS input (AGC on) ......................... 350–6,500 Hz, +0/−3 dB ref. to 1 kHz
Distortion ..................................................................................................... 1.5% maximum THD @ 1 kHz
Mechanical
Dimensions ............................................. 8.12 H  8.12 W  6.12 D inches (206  206  155 mm), overall
Shipping weight .................................................................................................................... 7.1 lbs. (3.2 kg)
Net weight ............................................................................................................................. 6.1 lbs. (2.8 kg)
Environmental
Temperature range ........................................ −22° F to +158° F (−30° C to +70° C), operating and storage
Humidity ..................................................................................................................... 95%, non-condensing
Approvals
NRTL Listed for USA and Canada ........................................................ Class I, Div. 2, Groups A, B, C, D;
when used with listed GAI-Tronics 702 and 703 Series enclosures
Class I, Div. 2, Groups A, B, C, D;
Class II, Div. 2, Groups F, G; Class III, Div. 2
when used with listed GAI-Tronics 732, 733, 7325, and 7335 Series enclosures
Temperature code........................................................................................................................................ T4
f:\standard ioms - current release\42004 instr. manuals\42004-658l2g.doc
03/12
Pub. 42004-658L2G
PAGE 14 of 14
®
701-902 SMARTSERIES HANDSET/SPEAKER AMPLIFIER
Replacement Parts
Model No
Description
10112-101
Handset Assembly
46101-012
Amplifier Enclosure Mounting Hardware
12511-001
Dynamic Transmitter and Cap
12523-001
GAI-Tronics Nameplate Kit
69383-001
Handset/FSK/P PCBA
69382-001
Speaker Amp/Power Supply PCBA
13204-002
Receiver Cap
51008-003
Pressbar Switch
12514-004
6-foot Hytrel Cord and Bushing
12514-007
6-foot PVC Cord with Bushing
12502-101
Replacement Receiver Kit
12512-008
Hookswitch/Cradle Kit
f:\standard ioms - current release\42004 instr. manuals\42004-658l2g.doc
03/12
Warranty
Equipment.
GAI-Tronics warrants for a period of one (1) year from the date of shipment, that any
GAI-Tronics equipment supplied hereunder shall be free of defects in material and workmanship, shall
comply with the then-current product specifications and product literature, and if applicable, shall be fit
for the purpose specified in the agreed-upon quotation or proposal document. If (a) Seller’s goods prove
to be defective in workmanship and/or material under normal and proper usage, or unfit for the purpose
specified and agreed upon, and (b) Buyer’s claim is made within the warranty period set forth above,
Buyer may return such goods to GAI-Tronics’ nearest depot repair facility, freight prepaid, at which time
they will be repaired or replaced, at Seller’s option, without charge to Buyer. Repair or replacement shall
be Buyer’s sole and exclusive remedy. The warranty period on any repaired or replacement equipment
shall be the greater of the ninety (90) day repair warranty or one (1) year from the date the original
equipment was shipped. In no event shall GAI-Tronics warranty obligations with respect to equipment
exceed 100% of the total cost of the equipment supplied hereunder. Buyer may also be entitled to the
manufacturer’s warranty on any third-party goods supplied by GAI-Tronics hereunder. The applicability
of any such third-party warranty will be determined by GAI-Tronics.
Services.
Any services GAI-Tronics provides hereunder, whether directly or through subcontractors,
shall be performed in accordance with the standard of care with which such services are normally
provided in the industry. If the services fail to meet the applicable industry standard, GAI-Tronics will
re-perform such services at no cost to buyer to correct said deficiency to Company's satisfaction provided
any and all issues are identified prior to the demobilization of the Contractor’s personnel from the work
site. Re-performance of services shall be Buyer’s sole and exclusive remedy, and in no event shall GAITronics warranty obligations with respect to services exceed 100% of the total cost of the services
provided hereunder.
Warranty Periods.
Every claim by Buyer alleging a defect in the goods and/or services provided
hereunder shall be deemed waived unless such claim is made in writing within the applicable warranty
periods as set forth above. Provided, however, that if the defect complained of is latent and not
discoverable within the above warranty periods, every claim arising on account of such latent defect shall
be deemed waived unless it is made in writing within a reasonable time after such latent defect is or
should have been discovered by Buyer.
Limitations / Exclusions.
The warranties herein shall not apply to, and GAI-Tronics shall not be
responsible for, any damage to the goods or failure of the services supplied hereunder, to the extent
caused by Buyer’s neglect, failure to follow operational and maintenance procedures provided with the
equipment, or the use of technicians not specifically authorized by GAI-Tronics to maintain or service the
equipment. THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE IN LIEU OF AND
EXCLUDE ALL OTHER WARRANTIES AND REMEDIES, WHETHER EXPRESS OR IMPLIED BY
OPERATION OF LAW OR OTHERWISE, INCLUDING ANY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Return Policy
If the equipment requires service, contact your Regional Service Center for a return authorization number
(RA#). Equipment should be shipped prepaid to GAI-Tronics with a return authorization number and a
purchase order number. If the equipment is under warranty, repairs or a replacement will be made in
accordance with the warranty policy set forth above. Please include a written explanation of all defects to
assist our technicians in their troubleshooting efforts.
Call 800-492-1212 (inside the USA) or 610-777-1374 (outside the USA) for help identifying the
Regional Service Center closest to you.
(Rev. 10/06)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement