Celestron C100ED-R Instruction manual

PDF Download

Document

A d v d a v n a c n e c d e d

S e

S r r i i e r e r i i s e

I I N S T R U C T I I O N M A N U A L s

G T

C 8 0 E D R ● C 1 0 0 E D R

INTRODUCTION................................................................................................................................ ............4

Warning ...................................................................................................................................................... 4

ASSEMBLY .................................................................................................................................................................... 6

Setting up the Tripod .................................................................................................................................. 6

Attaching the Equatorial Mount ................................................................................................................. 6

Attaching the Center Leg Brace ................................................................................................................. 7

Installing the Counterweight Bar................................................................................................................ 7

Installing the Counterweight ...................................................................................................................... 8

Attaching the Hand Control Holder............................................................................................................ 8

Attaching the Slow Motion Knobs ............................................................................................................. 8

Attaching the Telescope Tube to the Mount............................................................................................... 9

The Optical Tube...................................................................................................................................... 10

Balancing the Tube in R.A. ...................................................................................................................... 11

Adjusting the Mount................................................................................................................................. 12

Adjusting the Mount in Altitude ............................................................................................................... 13

Adjusting the Mount in Azimuth .............................................................................................................. 13

Attaching the Declination Cable (For GT Models Only) ......................................................................... 13

Powering the Telescope............................................................................................................................ 14

HAND CONTROL ....................................................................................................................................................... 15

Hand Control Operation ........................................................................................................................... 16

Alignment Procedures .............................................................................................................................. 17

Startup Procedure ..................................................................................................................................... 17

Auto Align................................................................................................................................................ 18

Auto Three-Star Align .............................................................................................................................. 18

Quick-Align.............................................................................................................................................. 19

Last Alignment ......................................................................................................................................... 19

Re-Alignment ........................................................................................................................................... 19

Object Catalog .......................................................................................................................................... 20

Selecting an Object ................................................................................................................................... 20

Slewing to an Object................................................................................................................................. 20

Finding Planets ......................................................................................................................................... 20

Tour Mode ................................................................................................................................................ 21

Constellation Tour .................................................................................................................................... 21

Direction Buttons...................................................................................................................................... 21

Rate Button ............................................................................................................................................... 21

Setup Procedures ...................................................................................................................................... 22

Tracking Mode ................................................................................................................................. 22

Tracking Rate ................................................................................................................................... 22

Date/Time ......................................................................................................................................... 22

User Defined Objects........................................................................................................................ 22

Get RA/DEC..................................................................................................................................... 23

Goto R.A/Dec ................................................................................................................................... 23

Identify ............................................................................................................................................. 23

Precise GoTo............................................................................................................................................. 24

Scope Setup Features ................................................................................................................................ 24

Setup Time-Site ................................................................................................................................ 24

Anti-backlash.................................................................................................................................... 24

Filter Limits ...................................................................................................................................... 24

Direction Buttons.............................................................................................................................. 25

Goto Approach ................................................................................................................................. 25

Autoguide Rates ............................................................................................................................... 25

Azimuth Limits................................................................................................................................. 25

East/West Filtering ........................................................................................................................... 26

Utility Features ......................................................................................................................................... 26

Calibrate Goto .................................................................................................................................. 26

Home Position .................................................................................................................................. 26

Polar Align ....................................................................................................................................... 26

Light Control .................................................................................................................................... 27

Factory Settings ................................................................................................................................ 27

Version ............................................................................................................................................. 27

Get Alt-Az ........................................................................................................................................ 27

Goto Alt-Az ...................................................................................................................................... 27

Hibernate .......................................................................................................................................... 27

Turn On/Off GPS ............................................................................................................................. 27

TELESCOPE BASICS ................................................................................................................................................. 29

Image Orientation ..................................................................................................................................... 29

Focusing ................................................................................................................................................... 30

Aligning the Finderscope ......................................................................................................................... 30

Calculating Magnification ........................................................................................................................ 30

Determining Field of View ....................................................................................................................... 31

General Observing Hints........................................................................................................................... 31

ASTRONOMY BASICS............................................................................................................................................... 32

The Celestial Coordinate System.............................................................................................................. 32

Motion of the Stars ................................................................................................................................... 33

Finding the North Celestial Pole............................................................................................................... 35

Declination Drift Method of Polar Alignment.......................................................................................... 36

CELESTIAL OBSERVING......................................................................................................................................... 37

Observing the Moon ................................................................................................................................. 37

Lunar Observing Hints.............................................................................................................................. 37

Observing the Planets ............................................................................................................................... 37

Observing the Sun..................................................................................................................................... 37

Solar Observing Hints............................................................................................................................... 38

Observing Deep Sky Objects .................................................................................................................... 38

Seeing Conditions ..................................................................................................................................... 38

Transparency............................................................................................................................................. 38

Sky Illumination ....................................................................................................................................... 38

Seeing ....................................................................................................................................................... 38

ASTROPHOTOGRAPHY ........................................................................................................................................... 40

Piggyback ................................................................................................................................................. 40

Short Exposure Prime Focus Photography ............................................................................................... 41

Terrestrial Photography ............................................................................................................................ 42

Metering.................................................................................................................................................... 42

Reducing Vibration................................................................................................................................... 42

Auto Guiding ............................................................................................................................................ 43

TELESCOPE MAINTENANCE ................................................................................................................................. 44

Care and Cleaning of the Optics............................................................................................................... 44

OPTIONAL ACCESSORIES..................................................................................................................................... 45

APPENDIX A – TECHNICAL SPECIFICATIONS ............................................................................................... 47

APPENDIX B – GLOSSARY OF TERMS ............................................................................................................... 48

APPENDIX C – LONGITUDES AND LATITUDES ................................................................................................ 51

APPENDIX D – RS-232 CONNECTION ................................................................................................................... 56

APPENDIX E – TIME ZONE MAP ........................................................................................................................... 58

SKY MAPS.................................................................................................................................................................... 60

Congratulations on your purchase of the Celestron Advanced Series telescope (AST)! The Advanced Series of telescopes come in standard (non-computerized) and computerized GT models. The Advanced Series is made of the highest quality materials to ensure stability and durability. All this adds up to a telescope that gives you a lifetime of pleasure with a minimal amount of maintenance. Furthermore, your Celestron telescope is versatile — it will grow as your interest grows.

The Advanced GT Series ushers in the next generation of computer automated telescopes. The Celestron Advanced GT series continues in this proud tradition combining large aperture optics with the sophistication and ease of use of our computerized

GoTo mount.

If you are new to astronomy, you may wish to start off by using the built-in Sky Tour feature, which commands the telescopes to find the most interesting objects in the sky and automatically slews to each one. Or if you are an experienced amateur, you will appreciate the comprehensive database of over 40,000 objects, including customized lists of all the best deep-sky objects, bright double stars and variable stars. No matter at what level you are starting out, the Advanced Series telescopes will unfold for you and your friends all the wonders of the Universe.

Some of the many standard features of the Advanced GT include:

• Fully enclosed optical encoders for position location.

• Ergonomically designed mount that disassembles into compact and portable pieces.

• Database filter limits for creating custom object lists.

• Storage for programmable user defined objects; and

Many other high performance features!

The AST’s deluxe features combine with Celestron’s legendary optical systems to give amateur astronomers the most sophisticated and easy to use telescopes available on the market today.

Take time to read through this manual before embarking on your journey through the Universe. It may take a few observing sessions to become familiar with your telescope, so you should keep this manual handy until you have fully mastered your telescope’s operation. The Advanced GT hand control has built-in instructions to guide you through all the alignment procedures needed to have the telescope up and running in minutes. Use this manual in conjunction with the on-screen instructions provided by the hand control. The manual gives detailed information regarding each step as well as needed reference material and helpful hints guaranteed to make your observing experience as simple and pleasurable as possible.

Your telescope is designed to give you years of fun and rewarding observations. However, there are a few things to consider before using your telescope that will ensure your safety and protect your equipment.

Warning

Never look directly at the sun with the naked eye or with a telescope (unless you have the proper solar filter). Permanent and irreversible eye damage may result.

Never use your telescope to project an image of the sun onto any surface. Internal heat build-up can damage the telescope

and any accessories attached to it.

Never use an eyepiece solar filter or a Herschel wedge. Internal heat build-up inside the telescope can cause these devices to crack or break, allowing unfiltered sunlight to pass through to the eye.

Never leave the telescope unsupervised, either when children are present or adults who may not be familiar with the correct operating procedures of your telescope .

5.

6.

7.

8.

1.

2.

3.

4.

7 B

Fig 1-2 - The Advanced GT Series

C80-GT Shown

Objective Lens

Declination Motor Drive

RA /Dec locks

Counterweight Bar

Counterweights

Center Leg Brace / Accessory Tray A.

2" Steel Tripod

Hand Control

B.

C. R.A. Motor Drive / Control Panel

10.

11.

12.

13. Focuser

Diagonal

Eyepiece

Finderscope

CONTROL PANEL

Hand Control Port

Dec Motor Port

Autoguide Port

12v Output Jack

ON/OFF Switch

This section covers the assembly instructions for your Celestron Advanced Series Telescope (AST). Your AST telescope should be set up indoor the first time so that it is easy to identify the various parts and familiarize yourself with the correct assembly procedure before attempting it outdoor.

21021/21022

C80ED-R

21026 / 21027

C100ED-R

Diameter 80mm (3.2") refractor 100mm (4.0") refractor

Focal Length

Eyepiece

Finderscope

Mount

Tripod

Software

600mm F/7.5

20mm - 1.25" (30x)

6x30 9x50

CG-5 Equatorial

2" Stainless Steel

The Sky L1

900mm F/9

20mm - 1.25" (45x)

CG-5 Equatorial

2" Stainless Steel

The Sky L1

Counterweight

S e t t t t i i n g u p t t h e T r r i i p o d

The CG-5 tripod comes with an all metal center leg brace / accessory tray to give rock solid support to the mount.

The tripod comes fully assembled with a metal plate, called the tripod head, that holds the legs together at the top.

In addition, there is a central rod that extends down from the tripod head that attaches the equatorial mount to the tripod. To set up the tripod:

1. Stand the tripod upright and pull the tripod legs apart until each leg is fully extended. The tripod will now stand by itself. Once the tripod is set up, you can adjust the height at which it stands.

2. Loosen the lever on the leg clamp so that the tripod leg can be adjusted.

3. Slide the center portion of the tripod leg away from the tripod

Equatorial

Mount

Azimuth

Alignment Screws

4. Tighten the levers on each leg clamp to hold the legs in place. head until it is at the desired height.

Tripod

Head Alignment

Peg

A t t t t a c h i i n g t t h e E q u a t t o r r i i a l l M o u n t t

The equatorial mount allows you to tilt the telescope’s axis of rotation so that you can track the stars as they move across the sky. The CG-5 mount is a German equatorial mount that

Mounting

Knob

Figure 2-3

attaches to the tripod head. On one side of the tripod head there is a metal alignment peg for aligning the mount.

This side of the tripod will face north when setting up for an astronomical observing session. To attach the equatorial head:

1. Locate the azimuth adjustment screws on the equatorial mount.

2. Retract the screws so they no longer extend into the azimuth housing on the mount. Do NOT remove the screws

since they are needed later for polar alignment.

3. Hold the equatorial mount over the tripod head so that the azimuth housing is above the metal peg.

4. Place the equatorial mount on the tripod head so that the two are flush.

5. Tighten the knob (attached to the central rod) on the underside of the tripod head to hold the equatorial mount firmly in place.

A t t t t a c h i i n g t t h e C e n t t e r r L e g B r r a c e

Slide the accessory tray over the central rod so that each arm of the tray is pushing against the inside of the tripod legs.

Thread the accessory tray knob on to the central rod and tighten.

I I n s t t a l l l l i i n g t t h e C o u n t t e r r w e i i g h t t B a r

To properly balance the telescope, the mount comes with a counterweight bar and at least one counterweight

(depending on model). To install the counterweight bar:

1. Locate the opening in the equatorial mount on the

DEC axis

2. Thread the counterweight bar into the opening until tight.

3. Tighten the counterweight bar lock nut fully for added support (see fig 2-5).

Once the bar is securely in place you are ready to attach the counterweight.

Mounting Knob

Figure 2-3

Central Rod

Accessory Tray

Accessory

Tray Knob

Figure 2-4

Since the fully assembled telescope can be quite heavy, position the mount so that the polar axis is pointing towards north before the tube assembly and counterweights are attached. This will make the polar alignment

procedure much easier.

I I n s t t a l l l l i i n g t t h e C o u n t t e r r w e i i g h t t

The Advanced Equatorial mount comes with either one or two counterweights (depending on the model). To install the counterweight(s):

1. Orient the mount so that the counterweight bar points toward the

Counterweight Bar

Locking Nut ground .

2. Remove the counterweight safety screw on the end of the counterweight bar (i.e., opposite the end that attaches to the mount).

Counterweight

Bar

3. Loosen the locking screw on the side of the counterweight.

4. Slide the counterweight onto the shaft (see Figure 2-5).

5. Tighten the locking screw on the side of the weight to hold the counterweight in place.

6. Replace the counterweight safety screw.

Locking Screw

Counterweight

Safety Screw

Figure 2-5

A t t t t a c h i i n g t t h e H a n d C o n t t r r o l l H o l l d e r r

( ( A d v a n c e d G T M o d e l l s O n l l y ) )

The Advanced GT telescope models come with a hand control holder to place the computerized hand control. The hand control holder comes in two pieces: the leg clamp that snaps around the tripod leg and the holder which attaches to the leg clamp. To attach the hand control holder:

1. Place the leg clamp up against one of the tripod legs and press firmly until the clamp wraps around the leg.

2. Slide the back of the hand control holder downward into the channel on the front of the legs clamp (see Fig 2-6) until it snaps into place.

A t t t t a c h i i n g t t h e S l l o w M o t t i i o n K n o b s

( ( F o r r N o n G T M o d e l l s O n l l y ) )

The Advanced Series (non-GT models) comes with two slow motion control knobs that allows you to make fine pointing adjustments to the telescope in both R.A. and Declination. To install the knobs:

1. Locate the hard plastic shell under the R.A. shafts.

2. Remove either of the two oval tabs by pulling tightly.

3. Line up the flat area on the inner portion of the R.A. slow motion knob with the flat area on the R.A. shaft

(see Fig 2-7).

Figure 2-6

Hand Control

Holder

Leg Clamp

Figure 2-7

4. Slide the R.A. slow motion knob onto the R.A. shaft.

The knob is a tension fit, so sliding it on holds it in place. As mentioned above, there are two R.A. shafts, one on

5. either side of the mount. It makes no difference which shaft you use since both work the same. Use whichever one you find more convenient. If, after a few observing sessions, you find the R.A. slow motion knob is more accessible from the other side, pull firmly to remove the knob, then install it on the opposite side.

The DEC slow motion knob attaches in the same manner as the R.A. knob. The shaft that the DEC slow motion knob fits over is toward the top of the mount, just below the telescope mounting platform. Once again, you have two shafts to choose from. Use the shaft that is pointing toward the ground. This makes it easy to reach while looking through the telescope, something which is quite important when you are observing.

A t t t t a c h i i n g t t h e T e l l e s c o p e T u b e t t o t t h e M o u n t t

The telescope attaches to the mount via a dovetail slide bar mounting bracket which is mounted along the

Advanced

GT Users! bottom of the telescope tube. Before you attach the optical tube, make sure that the declination and right ascension clutch knobs

are tight. This will ensure that the mount does not move suddenly while attaching the telescope. To mount the telescope tube:

Declination

Index Marks

In order for the GT computerized mount to function properly, before installing the optical tube, the mounting platform must be positioned so that the Declination Index Marks are aligned (see Fig

2-8).

1 Locate the mounting bracket from the box containing the equatorial mount head.

2 Attach the mounting bracket to the tube rings so that the tapered (narrow) end is against the bottom of the tube rings.

3 Loosen the hand knob on the side of the CG-5 mount.

Figure 2-8

4 Slide the mounting bracket that is attached to the bottom of the tube rings into the recess on the top of the mounting platform (see figure 2-9).

5 Tighten the telescope mounting screw on the

CG-5 mount to hold the telescope in place.

6 Hand tighten the mounting platform safety screw until the tip touches the side of the mounting bracket.

NOTE: Never loosen any of the knobs on the telescope tube or mount other than the R.A. and

DEC clutch knobs.

Figure 2-9

T h e O p t t i i c a l l T u b e

Objective Lens

Tube Ring

Clamp

Finderscope

Quick-release

Finderscope

Bracket

Dovetail / Photo

Tripod Mount

Focuser Knob

Focuser

Installing the Finderscope

To install the finderscope onto the telescope you must first mount the finderscope through the finder bracket and then attach it to the telescope. Toward the rear of the telescope tube, near the focusing assembly, there is a small bracket with a set screw in it. This is where the finderscope bracket will be mounted. To install the finderscope:

1. Slide the rubber O-ring over the eyepiece end of the finderscope and roll it 2/3 of the way up the finderscope.

2. Insert the eyepiece end of the finderscope through the bracket until the O-ring presses tightly between the finder and the inside of the bracket.

Tighten the adjustment screws until they make contact with the finderscope body.

Locate the mounting bracket near the front (open) end of the telescope.

5. Loosen the set screw on the mounting bracket on the telescope. Figure 2-10

6. Slide the finder bracket (attached to the finderscope) into the mounting bracket on the telescope.

7. The finderscope bracket will slide in from the back. The finderscope should be oriented so that the objective lens is toward the front (open) end of the telescope.

8. Tighten the set screw on the mounting bracket to hold the finderscope in place.

For information on aligning your finderscope, see Telescope Basics section of this manual.

Installing the Eyepieces

The eyepiece, or ocular as it is also called, is an optical element that magnifies the image focused by the telescope.

Without the eyepiece it would be impossible to use the telescope visually. The eyepiece fits directly into the focuser.

To attach an ocular:

1. Loosen the set screw on the eyepiece adapter so that it does not obstruct the inner diameter of the barrel.

Focuser Tension

Screw

1 ¼" Eyepiece

Adapter

2. Slide the chrome portion of the eyepiece into the focuser.

3. Tighten the set screw to hold the eyepiece in place.

To remove the eyepiece, loosen the set screw on the focuser and slide the eyepiece out. You can replace it with another ocular. Focuser Knob

Figure 2-11

Eyepieces are commonly referred to by focal length and barrel diameter. The focal length of each eyepiece is printed on the eyepiece barrel. The longer the focal length (i.e., the larger the number) the lower the eyepiece

T-Adapter

Thread

2" Focuser

Barrel magnification (i.e., power) and the shorter the focal length (i.e., the smaller the number) the higher the magnification. Generally, you will use low-to-moderate power when viewing. For more information on how to determine power, see the section on “Calculating Magnification.”

Your telescope can use eyepieces with both a 1-1/4" barrel diameter and 2" barrel diameter. To use a 2" barrel eyepiece, the 1 1/4" eyepiece adapter must first be removed. To do this, simply loosen the two chrome thumbscrews located around the focuser barrel (see figure 2-11) and remove the 1 1/4" adapter. Once removed, a 2" eyepiece or accessory can be inserted directly into the focuser barrel and secured with the two thumb screws.

B a l l a n c i i n g t t h e T u b e i i n R .

A .

To eliminate undue stress on the mount, the telescope should be properly balanced around the polar axis. In addition, proper balancing is crucial for accurate tracking if using an optional motor drive. To balance the mount:

1. Release the R.A. Clamp (see figure 2-15) and position the telescope off to one side of the mount (make sure that the mounting bracket screw is tight). The counterweight bar will extend horizontally on the opposite side of the mount

(see figure 2-12).

2. Release the telescope — GRADUALLY — to see which way the telescope “rolls.”

3. Loosen the set screw on the counterweight.

4. Move the counterweight to a point where it balances the telescope (i.e., it remains stationary when the R.A. clamp is released).

5. Tighten the set screw to hold the counterweight(s) in place.

These are general balance instructions and will reduce undue stress on the mount. When taking astrophotographs, this balance process should be done for the specific area at which the telescope is pointing.

Balancing the Telescope in DEC

The telescope should also be balanced on the declination axis to prevent any sudden motions when the DEC clamp

(Fig 2-5) is released. To balance the telescope in DEC:

1. Release the R.A. clamp and rotate the telescope so that it is on one side of the mount (i.e., as described in the previous section on balancing the telescope in R.A.).

2. Lock the R.A. clamp to hold the telescope in place.

3. Release the DEC clamp and rotate the telescope until the tube is parallel to the ground (see figure 2-13).

4. Release the tube — GRADUALLY — to see which way it rotates around the declination axis. DO NOT LET GO

OF THE TELESCOPE TUBE COMPLETELY!

5. Loosen the screws that hold the telescope tube inside the mounting rings and slide the telescope either forwards or backwards until it remains stationary when the DEC clamp is released.

6. Tighten the tube ring screws firmly to hold the telescope in place.

Figure 2-12 Figure 2-13

Like the R.A. balance, these are general balance instructions and will reduce undue stress on the mount. When taking astrophotographs, this balance process should be done for the specific area at which the telescope is pointing.

A d j j u s t t i i n g t t h e M o u n t t

In order for a motor drive to track accurately, the telescope’s axis of rotation must be parallel to the Earth’s axis of rotation, a process known as polar alignment. Polar alignment is achieved NOT by moving the telescope in R.A. or

DEC, but by adjusting the mount vertically, which is called altitude, and horizontally, which is called azimuth. This section simply covers the correct movement of the telescope during the polar alignment process. The actual process of polar alignment, that is making the telescope’s axis of rotation parallel to the Earth’s, is described later in this manual in the section on “Polar Alignment.”

Adjusting the Mount in Altitude

• To increase the latitude of the polar axis, tighten the rear latitude adjustment screw and loosen the front screw (if necessary).

• To decrease the latitude of the polar axis, tighten the front (under the counterweight bar) latitude adjustment screw and loosen the rear screw (if necessary).

The latitude adjustment on the CG-5 mount has a range from approximately 30° going up to 60°.

It is best to always make final adjustments in altitude by moving the mount against gravity (i.e. using the rear latitude adjustment screw to raise the mount). To do this

Rear Latitude

Adjustment

Screw you should loosen both latitude adjustment screws and manually push the front of the mount down as far as it will go. Then tighten the rear adjustment screw to raise the mount to the desired latitude.

Front Latitude

Adjustment Screw

For Advanced GT users, it may be helpful to remove the

Azimuth

Adjustment

Knobs front latitude adjustment screw completely. This will allow the mount to reach lower latitudes without the

Figure 2-14 screw coming into contact with the R.A. motor assembly.

To remove the latitude screw, first use the rear screw to raise the mount head all the way up. Then remove the front latitude screw completely. Now you should be able to manually move the mount head all the way to its lowest latitude. Now, using only the rear screw, raise the mount to your desired latitude.

Adjusting the Mount in Azimuth

For rough adjustments in azimuth, simply pick up the telescope and tripod and move it. For fine adjustments in azimuth:

1. Turn the azimuth adjustment knobs located on either side of the azimuth housing (see Fig 2-14). While standing behind the telescope, the knobs are on the front of the mount.

• Turning the right adjustment knob clockwise moves the mount toward the right.

• Turning the left adjustment knob clockwise moves the mount to the left.

Both screws push off of the peg on the tripod head, which means you may have to loosen one screw while tightening the other. The screw that holds the equatorial mount to the tripod may have to be loosened slightly.

Keep in mind that adjusting the mount is done during the polar alignment process only. Once polar aligned, the mount must NOT be moved. Pointing the telescope is done by moving the mount in right ascension and declination, as described earlier in this manual.

A t t t t a c h i i n g t t h e D e c l l i i n a t t i i o n C a b l l e ( ( F o r r G T M o d e l l s O n l l y ) )

The Advanced Series mount comes with a declination cable that connects from the R.A. motor drive electronic panel to the Dec motor drive. To attach the motor cable:

Locate the Declination cable and plug one end of the cable into the port on the electronics panel labeled DEC Port and plug the other end of the cable into the port located on the declination motor drive (see Fig 2-15).

P o w e r r i i n g t t h e T e l l e s c o p e

The Advanced GT can be powered by the supplied car battery adapter or optional 12v AC adapter. Use only adapters supplied by Celestron. Using any other adapter may damage the electronics or cause the telescope not to operate properly, and will void your manufacturer's warranty.

1. To power the telescope with the car battery adapter (or 12v AC adapter), simply plug the round post into the

12v outlet on the electronic panel and plug the other end into your cars cigarette lighter outlet or portable power supply (see Optional Accessories). Note: to prevent the power cord from being accidentally pulled out, wrap the power cord around the strain relief located below the power switch.

2. Turn on the power to the telescope by flipping the switch, located on the electronics panel, to the "On" position.

DEC Locking

Clamp

R.A. Locking

Clamp Declination Cable

Input Port

Declination Cable

Output Port

12v Power Input

On/Off Switch

Figure 2-15

The Advanced Series GT, computerized version of each telescope has a hand controller designed to give you instant access to all the functions that your telescope has to offer. With automatic slewing to over 40,000 objects, and common sense menu descriptions, even a beginner can master its variety of features in just a few observing sessions.

Below is a brief description of the individual components of the computerized hand controller:

1. Liquid Crystal Display (LCD) Window: Has a dual-line, 16 character display screen that is backlit for comfortable viewing of telescope information and scrolling text.

2. Align: Instructs the telescope to use a selected star or object as an alignment position.

3. Direction Keys: Allows complete control of the telescope in any direction. Use the direction keys to move the telescope to the initial alignment stars or for centering objects in the eyepiece.

Figure 3-1

The Advanced GT Hand Control

4. Catalog Keys: The Advanced Series has keys on the hand control to allow direct access to each of the catalogs in its database. The hand control contains the following catalogs in its database:

Messier – Complete list of all Messier objects.

NGC – Complete list of all the deep-sky objects in the Revised New General Catalog.

Caldwell – A combination of the best NGC and IC objects.

Planets - All 8 planets in our Solar System plus the Moon.

Stars – A compiled list of the brightest stars from the SAO catalog.

List – For quick access, all of the best and most popular objects in the Advanced GT database have been broken down into lists based on their type and/or common name:

Named Stars Common name listing of the brightest stars in the sky.

Named Objects Alphabetical listing of over 50 of the most popular

Double Stars deep sky objects.

Numeric-alphabetical listing of the most visually stunning double, triple and quadruple stars in the

Variable Stars

Asterisms sky.

Select list of the brightest variable stars with the shortest period of changing magnitude.

A unique list of some of the most recognizable star

CCD Objects patterns in the sky.

A custom list of many interesting galaxy pairs, trios and clusters that are well suited for CCD imaging

IC Objects

Abell Objects

Constellation with the Advanced GT telescope.

A complete list of all the Index Catalog deep-sky objects.

A custom list of the Abell Catalog deep-sky galaxies.

A complete list of all 88 constellations.

5. Info: Displays coordinates and useful information about objects selected from the Advanced GT database.

6. Tour: Activates the tour mode, which seeks out all the best objects for the current date and time, and automatically slews the telescope to those objects.

7. Enter: Pressing Enter allows you to select any of the Advanced GT functions and accept entered parameters.

8. Undo: Undo will take you out of the current menu and display the previous level of the menu path. Press

Undo repeatedly to get back to a main menu or use it to erase data entered by mistake.

9. Menu: Displays the many setup and utilities functions such as tracking rates and user defined objects and many others.

10. Scroll Keys: Used to scroll up and down within any of the menu lists. A double-arrow will appear on the right side of the LCD when there are sub-menus below the displayed menu. Using these keys will scroll through those sub-menus.

11. Rate: Instantly changes the rate of speed of the motors when the direction buttons are pressed.

12. RS-232 Jack: Allows you to interface with a computer and control the telescope remotely.

H a n d C o n t t r r o l l O p e r r a t t i i o n

This section describes the basic hand control procedures needed to operate the GT Series Telescopes. These procedures are grouped into three categories: Alignment, Setup and Utilities. The alignment section deals with the initial telescope alignment as well as finding objects in the sky; the setup section discusses changing parameters such as tracking mode and tracking rate; finally, the last section reviews all of the utilities functions such as calibrating your mount, polar alignment and backlash compensation.

A l l i i g n m e n t P r r o c e d u r r e s

In order for the telescope to accurately point to objects in the sky, it must first be aligned to three known positions

(stars) in the sky. With this information, the telescope can create a model of the sky, which it uses to locate any object with known coordinates. There are many ways to align your telescope with the sky depending on what information the user is able to provide: Auto Align allows the telescope to select three stars and uses the entered time/location information to align the telescope; Auto Three Star Align involves the same process as Auto Align, however it allows the user to select which star to use to align the telescope. Quick-Align will ask you to input all the same information as you would for the Auto Align procedure. However, instead of slewing to the alignment stars for centering and alignment, the telescope bypasses this step and simply models the sky based on the information given. Finally, Last Alignment restores your last saved star alignment and switch position. Last Alignment also serves as a good safeguard in case the telescope should lose power.

S t t a r r t t u p P r r o c e d u r r e

Before any of the described alignments are performed, the telescope mount needs to be positioned so that the index marks are aligned on both the right ascension and declination axes (see Fig 2-8).

First index its switch position so that each axis has an equal amount of travel to move in either direction. Once the index position has been set, the hand control will display the last entered date and time information stored in the hand control. Once the telescope is powered on:

1. Press ENTER begin the alignment process.

2. The hand control will ask the user to set the mount to its index position. Move the telescope mount, either manually or with the hand control, so that the index marked in both R.A. and

Dec are aligned (see Fig 2-8). Press Enter to continue.

3. The hand control will then display the last entered local time, date, time zone, longitude and latitude.

• Use the Up/Down keys (10) to view the current parameters.

• Press ENTER to accept the current parameters.

• Press UNDO to enter current date and time information into the hand control. The following information will be displayed:

Mount Calibration

After an Auto Align is successfully completed, the hand control will display the message, Calibrating...

This automatic calibration routine is necessary to calculate and compensates for "cone" error inherent in all German equatorial mounts. Cone error is the inaccuracy that results from the optical tube not being exactly perpendicular to the mounts declination axis as well as various other inaccuracies such as backlash in the mounts gears. The telescope is able to automatically determine the cone error value by always using

Time - Enter the current local time for your area. You can enter either the local time (i.e.

08:00), or you can enter military time (i.e.

20:00 ).

• Select PM or AM. If military time was entered,

• the hand control will bypass this step.

Choose between Standard time or Daylight

Savings time. Use the Up and Down scroll buttons alignment stars on both sides of the

Meridian (see Figure 3-2).

Mechanical errors can be reduced further by always centering alignment stars using the up and right arrow buttons as described in the Pointing Accuracy box below.

•

(10) to toggle between options.

Select the time zone that you are observing from. Again, use the Up and Down buttons (10) to scroll through the choices. Refer to Time Zone map in Appendix for more information.

Date - Enter the month, day and year of your observing session.

• Finally, you must enter the longitude and latitude of the location of your observing site. Use the table in Appendix C to locate the closest longitude and latitude for your current observing location and enter those numbers when asked in the hand control, pressing ENTER after each entry. Remember to select "West" for longitudes in North America and "North" for latitudes in the North Hemisphere. For international cities, the correct hemisphere is indicated in the

Appendix listings.

4. Select one of the four alignment methods as described below.

Note: If incorrect information is entered into the hand control, the UNDO button acts like a back space button allowing the user to re-enter the correct data.

A u t t o A l l i i g n

Auto Align allows the telescope to automatically choose three stars

(two on one side of the Meridian, and one on the opposite side) on which to align itself. To Auto Align your telescope:

1. Select Auto Align from the alignment choices given.

Based on the date and time information entered, the telescope will automatically select and go to a bright star that is above the horizon.

• If for some reason the chosen star is not visible

(perhaps behind a tree or building) press UNDO to automatically select the next bright star from the database star list.

2. Once the telescope is finished slewing to your first alignment star, the display will ask you to use the arrow buttons to align the selected star with the crosshairs in the center of the finderscope. Once centered in the finder, press ENTER.

3. The display will then instruct you to center the star in the field of view of the eyepiece. When the star is centered, press ALIGN to accept this star as your first alignment star.

Figure 3-2

The Meridian is an imaginary line in the sky that starts at the North celestial pole and ends at the South celestial pole and passes through the zenith. If you are facing South, the meridian starts from your Southern horizon and passes directly overhead to the

North celestial pole.

4. After the first alignment star has been entered the telescope will automatically select a second alignment star on the same side of the Meridian and have you repeat this procedure for that star.

5. For the third alignment star, the telescope will select a bright star on the opposite side of the Meridian and slew to it. Once again center the star in the crosshairs of the finderscope and then center the star in the eyepiece, pressing ENTER when complete.

When the telescope has been aligned on all three stars the display will read Alignment Successful, and you are now ready to find your first object.

A u t t o T h r r e e S t t a r A l l i i g n

Auto Three-Star Alignment works much the same way as Auto Align, however instead of automatically slewing to the alignment stars, the user is allowed to select the alignment stars from a list. To use Auto Three-Star Align:

1. Select Auto Three Star Align from the alignment choices given.

2. The hand control will display a recommended alignment star to begin.

• Press UNDO to display the next recommended star on the same side of the Meridian, or

• Press the UP and DOWN arrows keys to scroll through the compete list of available alignment stars to choose from.

3. Once the desired alignment star is displayed on the hand control press ENTER to slew the telescope to the star.

4. As with the Auto Align procedure, you will be asked to center the star in the crosshairs of the finderscope and then center the star in

Pointing Accuracy

For the best possible pointing accuracy, always center the alignment stars using the up arrow button and the right arrow button.

Approaching from this direction when looking through the eyepiece will eliminate much of the backlash between the gears and assures the most accurate alignment possible.

the eyepiece, pressing ENTER when complete.

NOTE: Although the telescope allows the user to select the alignment stars, for best all-sky pointing accuracy it is still necessary to select two alignment stars on one side of the Meridian and the third star on the opposite side of the Meridian. For this reason, the hand control will only display stars that are on the same side of the Meridian for the first two alignment stars, then will only display stars on the opposite side of the Meridian for the third alignment star.

Q u i i c k A l l i i g n

Quick-Align uses all the date and time information entered at startup to align the telescope. However, instead of slewing to the alignment stars for centering and alignment, the telescope bypasses this step and simply models the sky based on the information given. This will allow you to roughly slew to the coordinates of bright objects like the moon and planets and gives the telescope the information needed to track objects in any part of the sky (depending on accuracy of polar alignment). Quick-Align is not meant to be used to accurately locate small or faint deep-sky objects or to track objects accurately for photography.

To use Quick-Align, simply select Quick Align from the alignment options and press ENTER. The telescope will automatically use the entered date/time parameters to align itself with the sky and display Alignment Successful.

NOTE: Once a Quick-Align has been done, you can use the Re-alignment feature (see below) to improve your telescopes pointing accuracy.

L a s t t A l l i i g n m e n t t

The Last Alignment method will automatically recall the last stored index positions to continue using the alignment that was saved when the telescope was last powered down. This is a useful feature should your telescope accidentally lose power or be powered down.

NOTE: Just like with Quick-Align, you can use the Re-alignment feature (see below) to improve your telescopes pointing accuracy after using the Last Alignment method. To maintain a more accurate alignment over a series of observing sessions, use the Hibernate feature described later in this chapter.

R e A l l i i g n m e n t t

The Advanced Series telescopes have a re-alignment feature which allows you to replace any of the original alignment stars with a new star or celestial object. This can be useful in several situations:

• If you are observing over a period of a few hours, you may notice that your original two alignment stars have drifted towards the west considerably. (Remember that the stars are moving at a rate of 15º every hour). Aligning on a new star that is in the eastern part of the sky will improve your pointing accuracy, especially on objects in that part of the sky.

• If you have aligned your telescope using the Quick-Align method, you can use re-align to align on actual objects in the sky. This will improve the pointing accuracy of your telescope without having to re-enter addition information.

To replace an existing alignment star with a new alignment star:

1. Select the desired star (or object) from the database and slew to it.

2. Carefully center the object in the eyepiece.

3. Once centered, press the UNDO button until you are at the main menu.

4. With

Advanced GT displayed, press the ALIGN key on the hand control.

5. The display will then ask you which alignment star you want to replace. Use the UP and Down scroll keys to select the alignment star to be replaced. It is usually best to replace the star closest to the new object.

This will space out your alignment stars across the sky.

6. Press ALIGN to make the change.

Helpful

Hint

O b j j e c t t C a t t a l l o g

Selecting an Object

Now that the telescope is properly aligned, you can choose an object from any of the catalogs in the telescope's extensive database. The hand control has a key (4) designated for each of the catalogs in its database. There are two ways to select objects from the database: scrolling through the named object lists and entering object numbers.

Pressing the LIST key on the hand control will access all objects in the database that have common names or types. Each list is broken down into the following categories: Named Stars, Named Object, Double Stars,

Variable Stars, Asterisms and CCD Objects. Selecting any one of these catalogs will display a numericalphabetical listing of the objects under that list. Pressing the Up and Down keys (10) allows you to scroll through the catalog to the desired object.

When scrolling through a long list of objects, holding down either the Up or Down key will allow you to scroll through the catalog more rapidly by only displaying every fifth catalog object.

Pressing any of the other catalog keys (M, CALD, NGC, or STAR) will display a blinking cursor below the name of the catalog chosen. Use the numeric key pad to enter the number of any object within these standardized catalogs.

For example, to find the Orion Nebula, press the "M" key and enter "042".

Slewing to an Object

Once the desired object is displayed on the hand control screen, choose from the following options:

• Press the INFO Key. This will give you useful information about the selected object such as R.A.

• and declination, magnitude size and text information for many of the most popular objects.

Press the ENTER Key. This will automatically slew the telescope to the coordinates of the object.

Caution: Never slew the telescope when someone is looking into the eyepiece. The telescope can move at fast slew speeds and may hit an observer in the eye.

Object information can be obtained without having to do a star alignment. After the telescope is powered on, pressing any of the catalog keys allows you to scroll through object lists or enter catalog numbers and view the information about the object as described above.

Finding Planets

Your telescope can locate all 8 of our solar systems planets plus the Moon. However, the hand control will only display the solar system objects that are above the horizon (or within its filter limits). To locate the planets, press the

PLANET key on the hand control. The hand control will display all solar system objects that are above the horizon:

•

Use the Up and Down keys to select the planet that you wish to observe.

Press INFO to access information on the displayed planet.

Press ENTER to slew to the displayed planet.

Tour Mode

The Advanced Series telescopes include a tour feature which automatically allows the user to choose from a list of interesting objects based on the date and time in which you are observing. The automatic tour will display only those objects that are within your set filter limits (see Filter Limits in the Setup Procedures section of the manual). To activate the Tour mode, press the TOUR key (6) on the hand control. The hand control will display the best objects to observe that are currently in the sky.

• To see information and data about the displayed object, press the INFO key.

•

To slew to the object displayed, press ENTER.

To see the next tour object, press the Up key.

Constellation Tour

In addition to the Tour Mode, your telescope has a Constellation Tour that allows the user to take a tour of all the best objects in each of the 88 constellations. Selecting Constellation from the LIST menu will display all the constellation names that are above the user defined horizon (filter limits). Once a constellation is selected, you can choose from any of the database object catalogs to produce a list of all the available objects in that constellation.

•

To see information and data about the displayed object, press the INFO key.

To slew to the object displayed, press ENTER.

To see the next tour object, press the Up key.

Direction Buttons

The hand control has four direction buttons (3) in the center of the hand control which control the telescope's motion in altitude (up and down) and azimuth (left and right). The telescope can be controlled at nine different speed rates.

Rate Button

Pressing the RATE key (11) allows you to instantly change the speed rate of the motors from high speed slew rate to precise guiding rate or anywhere in between. Each rate corresponds to a number on the hand controller key pad.

The number 9 is the fastest rate (3º per second, depending on power source) and is used for slewing between objects and locating alignment stars. The number 1 on the hand control is the slowest rate (.5x sidereal) and can be used for accurate centering of objects in the eyepiece and photographic guiding. To change the speed rate of the motors:

•

Press the RATE key on the hand control. The LCD will display the current speed rate.

Press the number on the hand control that corresponds to the desired speed. The number will appear in the upper-right corner of the LCD display to indicate that the rate has been changed.

The hand control has a "double button" feature that allows you to instantly speed up the motors without having to choose a speed rate. To use this feature, simply press the arrow button that corresponds to the direction that you want to move the telescope. While holding that button down, press the opposite directional button. This will increase the slew rate to the maximum slew rate.

The direction that a star moves in the eyepiece when a direction is pressed will change depending on which side of the Meridian the telescope tube is positioned. In order to change the direction of the arrow buttons, see Scope Setup

Features later in this section.

1 = .5x

2 = 1x (sidereal)

3 = 4x

4 = 8x

5 = 16x

6 = 64x

7 = .5º / sec

8 = 2º / sec

9 = 3º / sec

Nine available slew speeds

S e t t u p P r r o c e d u r r e s

The Advanced GT contains many user defined setup functions designed to give the user control over the telescope's many advanced features. All of the setup and utility features can be accessed by pressing the MENU key and scrolling through the options:

Tracking Mode

This allows you to change the way the telescope tracks depending on the type of mount being used to support the telescope. The telescope has three different tracking modes:

EQ North Used to track the sky when the telescope is polar aligned in the

Northern Hemisphere.

EQ South Used to track the sky when the telescope is polar aligned in the

Off

Southern Hemisphere.

When using the telescope for terrestrial (land) observation, the tracking can be turned off so that the telescope never moves.

Tracking Rate

In addition to being able to move the telescope with the hand control buttons, your telescope will continually track a celestial object as it moves across the night sky. The tracking rate can be changed depending on what type of object is being observed:

Sidereal This rate compensates for the rotation of the Earth by moving the telescope at the same rate as the rotation of the Earth, but in the opposite direction. When the telescope is polar aligned, this can be accomplished by moving the telescope in right ascension only.

Lunar Used for tracking the moon when observing the lunar landscape.

Solar Used for tracking the Sun when solar observing with the proper filter.

View Time-Site

Displays the current time and longitude/latitude downloaded from the optional CN-16 GPS receiver. It will also display other relevant time-site information like time zone, daylight saving and local sidereal time. Local sidereal time (LST) is useful for knowing the right ascension of celestial objects that are located on the

Meridian at that time. View Time-Site will always display the last saved time and location entered while it is linking with the GPS. Once current information has been received, it will update the displayed information. If GPS is switched off or not present, the hand control will only display the last saved time and location.

User Defined Objects

- Your telescope can store up to 400 different user defined objects in its memory. The objects can be daytime land objects or an interesting celestial object that you discover

Helpful

Hint that is not included in the regular database. There are several ways to save an object to memory depending on what type of object it is:

GoTo Object: To go to any of the user defined objects stored in the database, scroll down to either

GoTo Sky Obj or Goto Land Obj and enter the number of the object you wish to select and press ENTER. The telescope will automatically retrieve and display the coordinates before slewing to the object.

Save Sky Object: Your telescope stores celestial objects to its database by saving its right ascension and declination in the sky. This way the same object can be found each time the telescope is aligned. Once a desired object is centered in the eyepiece, simply scroll to the "

Save

Sky Obj" command and press ENTER. The display will ask you to enter a number between 1-200 to identify the object. Press ENTER again to save this object to the database.

Enter R.A. - Dec: You can also store a specific set of coordinates for an object just by entering the R.A. and declination for that object. Scroll to the "

Enter RA-DEC " command and press

ENTER. The display will then ask you to enter first the R.A. and then the declination of the desired object.

Save Land Object:

The telescope can also be used as a spotting scope on terrestrial objects. Fixed land objects can be stored by saving their altitude and azimuth relative to the location of the telescope at the time of observing. Since these objects are relative to the location of the telescope, they are only valid for that exact location. To save land objects, once again center the desired object in the eyepiece. Scroll down to the "

Save Land Obj" command and press ENTER. The display will ask you to enter a number between 1-200 to identify the object. Press ENTER again to save this object to the database.

To replace the contents of any of the user defined objects, simply save a new object using one of the existing identification numbers; the telescope will replace the previous user defined object with the current one.

Get RA/DEC

- Displays the right ascension and declination for the current position of the telescope.

Goto R.A/ Dec

- Allows you to input a specific R.A. and declination and slew to it.

To store a set of coordinates (R.A./Dec) permanently into the database, save it as a User Defined Object as described above.

Identify

Identify Mode will search any of the telescope's database catalogs or lists and display the name and offset distances to the nearest matching objects. This feature can serve two purposes. First, it can be used to identify an unknown object in the field of view of your eyepiece. Additionally, Identify Mode can be used to find other celestial objects that are close to the objects you are currently observing. For example, if your telescope is pointed at the brightest star in the constellation Lyra, choosing Identify and then searching the Named Star catalog will no doubt return the star Vega as the star you are observing. However, by selecting Identify and searching by the Named Object or

Messier catalogs, the hand control will let you know that the Ring Nebula (M57) is approximately 6° from your current position. Searching the Double Star catalog will reveal that Epsilon Lyrae is only 1° away from Vega. To use the Identify feature:

•

Press the Menu button and select the Identify option.

Use the Up/Down scroll keys to select the catalog that you would like to search.

Press ENTER to begin the search.

Note: Some of the databases contain thousands of objects, and can therefore take several minutes to return the closest objects.

Precise GoTo

The Advanced Series telescopes have a precise goto function that can assist in finding extremely faint objects and centering objects closer to the center of the field of view for astrophotography and CCD imaging. Precise Goto automatically searches out the closest bright star to the desired object and asks the user to carefully center it in the eyepiece. The hand control then calculates the small difference between its goto position and its centered position.

Using this offset, the telescope will then slew to the desired object with enhanced accuracy. To use Precise Goto:

SCOPE SETUP

1. Press the MENU button and use the Up/Down keys to select Precise Goto.

• Choose Database to select the object that you want to observe from any of the database catalogs listed or;

• Choose RA/DEC to enter a set of celestial coordinates that you wish to slew to.

SETUP TIME-SITE

ANTI-BACKLASH

2. Once the desired object is selected, the hand control will search out and display the closest bright star to your desired object. Press ENTER to slew to the bright

AZM POSITIVE

AZM NEGATIVE

ALT POSITIVE

ALT NEGATIVE

FILTER LIMITS alignment star.

3. Use the direction buttons to carefully center the alignment star in the eyepiece.

4. Press ENTER to slew to the desired object.

ALTMAX IN LIST

ALTMIN IN LIST

DIRECTION BUTTONS

Scope Setup Features

AZM BUTTONS

ALT BUTTONS

GOTO APPROACH

Setup Time-Site

-

Allows the user to customize the telescope's display by changing time and location parameters (such as time zone and daylight savings).

AZM APPROACH

ALT APPROACH

AUTOGUIDE RATES

Anti-backlash

– All mechanical gears have a certain amount of backlash or play between the gears. This play is evident by how long it takes for a star to move in the eyepiece when the hand control arrow buttons are pressed (especially when changing directions). The Advanced GT's anti-backlash features allows the user to compensate for backlash by inputting a value which quickly rewinds the motors just enough to eliminate the play between gears. The amount of compensation needed depends on the slewing rate selected; the slower the slewing rate the longer it will take for the star to appear to move in the eyepiece. There are two values for each axis, positive and negative. Positive is the amount of compensation applied when you press the button, in order to get the

AZM RATE

ALT RATE

AZIMUTH LIMITS

AZM MIN LIMIT

AZM MAX LIMIT

E/W FILTERING

FILTERING ON

FILTERING OFF gears moving quickly without a long pause. Negative is the amount of compensation applied when you release the button, winding the motors back in the other direction to resume tracking.

Normally both values should be the same.

You will need to experiment with different values (from 0-99); a value between 20 and 50 is usually best for most visual observing, whereas a higher value may be necessary for photographic guiding.

To set the anti-backlash value, scroll down to the anti-backlash option and press ENTER. While viewing an object in the eyepiece, observe the responsiveness of each of the four arrow buttons. Note which directions you see a pause in the star movement after the button has been pressed. Working one axis at a time, adjust the backlash settings high enough to cause immediate movement without resulting in a pronounced jump when pressing or releasing the button. Now, enter the same values for both positive and negative directions. If you notice a jump when releasing the button, but setting the values lower results in a pause when pressing the button, go with the higher value for positive, but use a lower value for negative. The telescope will remember these values and use them each time it is turned on until they are changed.

Filter Limits

– When an alignment is complete, the telescope automatically knows which celestial objects are above the horizon. As a result, when scrolling through the database lists (or selecting the Tour function), the hand control will display only those objects that are known to be above the horizon when you are observing. You can customize the object database by selecting altitude limits that are appropriate for your location and situation. For

Observing

Tip!

Helpful

Hint! example, if you are observing from a mountainous location where the horizon is partially obscured, you can set your minimum altitude limit to read +20º. This will make sure that the hand control only displays objects that are higher in altitude than 20º.

If you want to explore the entire object database, set the maximum altitude limit to 90º and the minimum limit to –

90º. This will display every object in the database lists regardless of whether it is visible in the sky from your location.

Direction Buttons –

The direction a star appears to move in the eyepiece changes depending on which side of the

Meridian the telescope tube is on. This can create confusion especially when guiding on a star when doing astrophotography. To compensate for this, the direction of the drive control keys can be changed. To reverse the button logic of the hand control, press the MENU button and select Direction Buttons from the Utilities menu. Use the Up/Down arrow keys (10) to select either the azimuth (right ascension) or altitude (declination) button direction and press ENTER. Select either positive or negative for both axes and press ENTER to save. Setting the azimuth button direction to positive will move the telescope in the same direction that the telescope tracks (i.e. towards the west). Setting the altitude buttons to positive will move the telescope counterclockwise along the DEC axis.

Goto Approach -

lets the user define the direction that the telescope will approach when slewing to an object.

This allows the user the ability to minimize the affects of backlash when slewing from object to object. Just like with Direction Buttons, setting GoTo Approach to positive will make the telescope approach an object from the same direction as tracking (west) for azimuth and counterclockwise in declination. Declination Goto approach will only apply while the telescope tube is on one side of the Meridian. Once the tube passes over to the other side of the

Meridian, the Goto approach will need to be reversed.

To change the Goto approach direction, simply choose Goto Approach from the Scope Setup menu, select either

Altitude or Azimuth approach, choose positive or negative and press ENTER.

In order to minimize the affect of gear backlash on pointing accuracy, the settings for Button Direction should ideally match the settings for GoTo Approach. By default, using the up and right direction buttons to center alignment stars will automatically eliminate much of the backlash in the gears. If you change the Goto approach of your telescope it is not necessary to change the Button Direction as well. Simply take notice of the direction the telescope moves when completing it final goto approach. If the telescope approaches its alignment star from the west

(negative azimuth) and clockwise (negative altitude) then make sure that the buttons used to center the alignment stars also move the telescope in the same directions.

Autoguide Rate –

Allows the user to set an autoguide rate as a percentage of sidereal rate. This is helpful when calibrating your telescope to a CCD autoguider for long exposure photography.

Azimuth Limits

- Sets the limits that the telescope can slew in azimuth (R.A.) The slew limits are set to 0º to

180º; with zero being the position of the telescope when the counterweight bar is extended out towards the west and 180º being the position when the counterweight bar is extended out

Fig 3-3 – Azimuth Slew Limits- This figure shows the full range of motion for the R.A. (azimuth) axis toward the east (see Fig 3-3). However, the slew limits can be customized depending on your needs. For example, if you are using CCD imaging equipment that has cables that are not long enough to move with the telescope as it slews across the sky, you can adjust the azimuth slew limit on the side of the mount that is restricted by the cables. Using the example above, the user could slew the telescope

in R.A. (azimuth) until it reaches the point that the cables are extended to their maximum. Then by displaying the telescopes azimuth in this position (by looking at Get Alt-Az under the Utilities menu) you can determine the telescopes azimuth at its most extended position. Enter this azimuth reading for either the maximum or minimum azimuth slew limit to ensure that the telescope will not slew beyond this point.

Warning: In order for the telescope to be able to slew to a star from the direction that minimizes the amount of backlash in the gears, it may be necessary for the telescope to slew beyond the specified slew limit in order to approach the star from the correct direction. This can limit your ability to slew to an object by as much as 6º from the azimuth slew limit set in the hand control. If this proves to be a problem, the direction that the telescope takes to center an object can be changed. To change the telescopes slewing direction, see Goto Approach under the Scope

Setup menu. In order to guaranty that the telescope will have a full range of motion in R.A. (azimuth), set the azimuth slew limits to 354 and 186. This will allow the mount to slew without regard to the slew limits.

East/West (E/W) Filtering

- In order to ensure the best possible full sky pointing accuracy, the Advanced series telescopes automatically filters and chooses its initial alignment stars so that the first two alignment stars are located on one side of the Meridian and the third star is on the opposite side of the Meridian. East/West Filtering allows you to turn off this automatic filtering feature, allowing the hand control to display all of its alignment stars when doing a Auto Three Star Align, without regard to the Meridian.

U t t i i l l i i t t y F e a t t u r r e s

Scrolling through the MENU (9) options will also provide access to several advanced utility functions within the

Advanced Series telescopes such as; Calibrate Goto, Polar Alignment, Hibernate as well as many others.

Calibrate Goto

- Goto Calibration is a useful tool when attaching heavy visual or photographic accessories to the telescope. Goto Calibration calculates the amount of distance and time it takes for the mount to complete its final slow goto when slewing to an object. Changing the

UTILITIES balance of the telescope can prolong the time it takes to complete the final slew.

Goto Calibration takes into account any slight imbalances and changes the final goto distance to compensate.

CALIBRATE GOTO

HOME POSTION

Home Position –

The telescopes "home" position is a user-definable position that is used to store the telescope when not in use. The home position is useful when storing

GOTO

SET the telescope in a permanent observatory facility. By default the Home position is the same as the index position used when aligning the mount. To set the Home position for your mount simply use the arrow buttons on the hand control to move the telescope mount to the desired position. Select the Set option and press Enter.

POLAR ALIGN

LIGHT CONTROL

Polar Align-

The Advanced GT has a polar alignment function that will help you KEYPAD OFF

KEYPAD ON

DISPLAY OFF

DISPLAY ON polar align your telescope for increased tracking precision and astrophotography.

After performing an Auto Alignment, the telescope will slew to where Polaris should be. By using the equatorial head to center Polaris in the eyepiece, the mount will then be pointed towards the actual North Celestial Pole. Once Polar Align is complete, you must re-align your telescope again using any of the alignment methods described earlier. To polar align the mount in the Northern Hemisphere:

1. With the telescope set up and roughly positioned towards Polaris, align the mount using the Auto Align or Auto Three Star method.

2. Select Polar Align from the Utilities menu and press Enter.

Based on your current alignment, the telescope will slew to where it thinks Polaris

FACTORY SETTING

PRESS UNDO

PRESS "0"

VERSION

GET ALT-AZ

GOTO ATL-AZ

HIBERNATE

TURN ON/OFF GPS

H i i e n l l p t t f f u l l should be. Use the equatorial head latitude and azimuth adjustments to place Polaris in the center of the eyepiece.

Do not use the direction buttons to position Polaris. Once Polaris is centered in the eyepiece press ENTER; the polar axis should then be pointed towards the North Celestial Pole.

Light Control

– This feature allows you to turn off both the red key pad light and LCD display for daytime use to conserve power and to help preserve your night vision.

Factory Settings

– Returns the Advanced GT hand control to its original factory settings. Parameters such as backlash compensation values, initial date and time, longitude/latitude along with slew and filter limits will be reset.

However, stored parameters such as user defined objects will remain saved even when Factory Settings is selected.

The hand control will ask you to press the "0" key before returning to the factory default setting.

Version

- Selecting this option will allow you to see the current version number of the hand control, motor control and GPS software (if using optional CN-16 GPS accessory). The first set of numbers indicate the hand control software version. For the motor control, the hand control will display two sets of numbers; the first numbers are for azimuth and the second set are for altitude. On the second line of the LCD, the GPS and serial bus versions are displayed.

Get Alt-Az

- Displays the relative altitude and azimuth for the current position of the telescope.

Goto Alt-Az

- Allows you to enter a specific altitude and azimuth position and slew to it.

Hibernate

- Hibernate allows the telescope to be completely powered down and still retain its alignment when turned back on. This not only saves power, but is ideal for those that have their telescopes permanently mounted or leave their telescope in one location for long periods of time. To place your telescope in Hibernate mode:

1. Select Hibernate from the Utility Menu.

2. Move the telescope to a desire position and press ENTER.

3. Power off the telescope. Remember to never move your telescope manually while in Hibernate mode.

Once the telescope is powered on again the display will read Wake Up. After pressing Enter you have the option of scrolling through the time/site information to confirm the current setting. Press ENTER to wake up the telescope.

Pressing UNDO at the Wake Up screen allows you to explore many of the features of the hand control without waking the telescope up from hibernate mode. To wake up the telescope after UNDO has been pressed, select

Hibernate from the Utility menu and press ENTER. Do not use the direction buttons to move the telescope while in hibernate mode.

Turn On/Off GPS

-

If using your Advanced GT telescope with the optional CN-16 GPS accessory (see Optional

Accessories section of the manual), you will need to turn the GPS on the first time you use the accessory. . If you want to use the telescope's database to find the coordinates of a celestial object for a future or past dates you would need to turn the GPS off in order to manually enter a time other than the present.

ADVANCED GT

MENU ALIGNMENT LIST

TRACKING

MODE

EQ NORTH

EQ SOUTH

OFF

RATE

SIDEREAL

SOLAR

LUNAR

VIEW TIME-SITE

SCOPE SETUP

SETUP TIME-SITE

ANTI-BACKLASH

FILTER LIMITS

DIRECTION BUTTONS

GOTO APPROACH

AUTOGUIDE RATE

AZIMUTH LIMITS

EAST/WEST FILTERING

UTILITIES

CALIBRATE GOTO

HOME POSITION

POLAR ALIGN

LIGHT CONTROL

FACTORY SETTING

VERSION

GET ALT-AZ

GOTO ALT-AZ

HIBERNATE

TURN ON/OFF GPS

USER OBJECTS

GOTO SKY OBJ

SAVE SKY OBJ

ENTER RA & DEC

SAVE LAND OBJ

GOTO LAND OBJ

GET RA-DEC

GOTO RA-DEC

IDENTIFY

SELECT CATALOG

PRECISE GOTO

GOTO TYPE

START-UP PROCUDURE

SET TO INDEX

ENTER TIME

DLS/ST

TIME ZONE

ENTER DATE- MM/DD/YY

ENTER LONG/LAT

AUTO ALIGN

CENTER STAR 1

CENTER STAR 2

CENTER STAR 3

AUTO THREE-STAR ALIGN

SELECT STAR 1

CENTER STAR 1

SELECT STAR 2

CENTER STAR 2

SELECT STAR 3

CENTER STAR 3

LAST ALIGNMENT

QUICK-ALIGN

NAMED STAR

NAMED OBJECT

ASTERISM

TOUR

VARIABLE STAR

DOUBLE STAR

CCD OBJECTS

ABELL

IC CATALOG

CALDWELL

MESSIER

NGC

SAO

SOLAR SYSTEM

CONSTELLATION

A telescope is an instrument that collects and focuses light. The nature of the optical design determines how the light is focused.

Some telescopes, known as refractors, use lenses. Other telescopes, known as reflectors, use mirrors. Developed in the early

1600s, the refractor is the oldest telescope design. It derives its name from the method it uses to focus incoming light rays. The refractor uses a lens to bend or refract incoming light rays, hence the name (see Figure 4-1). Early designs used single element lenses. However, the single lens acts like a prism and breaks light down into the colors of the rainbow, a phenomenon known as chromatic aberration. To get around this problem, a two-element lens, known as an achromat, was introduced. Each element has a different index of refraction allowing two different wavelengths of light to be focused at the same point. Most two-element lenses, usually made of crown and flint glasses, are corrected for red and green light. Blue light may still be focused at a slightly different point.

Figure 4-1

A c u t a w a y v i i e w o f f t h e l i g h t t p a t h o f t t h e R e f r a c t t o r o p t t i i c a l l d e s s i i g n

Image Orientation

It should be noted that the image orientation will change depending on the viewing configuration. When using the star diagonal, the image is right-side-up, but reversed from left-to-right. If inserting the eyepiece into the accessory adapter (i.e., without the star diagonal), the image is inverted (upside down and reversed from left-to-right). This holds true for the 9x50 finder as well as the telescope. For correct orientation through the telescope, which is important primarily for terrestrial observing, use the optional 45° erect image diagonal 1-1/4" (#94112-A).

Actual image orientation as seen with the unaided eye

Reversed from left to right, as viewed with a Star Diagonal

Figure 4-2

Inverted image, as viewed with the eyepiece directly in telescope

F o c u s i i n g

To focus your telescope, simply turn the focus knob located directly below the focuser. Turning the knob clockwise allows you to focus on an object that is farther than the one you are currently observing. Turning the knob counterclockwise from you allows you to focus on an object closer than the one you are currently observing.

• If you wear corrective lenses (specifically glasses), you may want to remove them when observing with an eyepiece attached to the telescope. However, when using a camera you should always wear corrective lenses to ensure the sharpest possible focus. If you have astigmatism, corrective lenses must be worn at all times.

A l l i i g n i i n g t t h e F i i n d e r r s c o p e

Accurate alignment of the finder makes it easy to find objects with the telescope, especially celestial objects. To make aligning the finder as easy as possible, this procedure should be done in the daytime when it is easy to find and identify objects. The finderscope has a spring-loaded adjustment screw that puts pressure on the finderscope while the remaining screws are used to adjust the finder horizontally and vertically. To align the finder:

1 Choose a target that is in excess of one mile away. This eliminates any possible parallax effect between the telescope and finder.

2 Release the R.A. and DEC clamps and point the telescope at your target.

3 Center your target in the main optics of the telescope. You may have to move the telescope slightly to center it.

4 Adjust the screw on the finder bracket that is on the right (when looking through the finder) until the cross hairs are centered horizontally on the target seen through the telescope.

5 Adjust the screw on the top of the finder bracket until the cross hairs are centered vertically on the target seen through the telescope.

Image orientation through the finder is inverted (i.e., upside down and backwards left-to-right). This is normal for any finder that is used straight-through. Because of this, it may take a few minutes to familiarize yourself with the directional change each screw makes on the finder.

Calculating Magnification

You can change the power of your telescope just by changing the eyepiece (ocular). To determine the magnification of your telescope, simply divide the focal length of the telescope by the focal length of the eyepiece used. In equation format, the formula looks like this:

Telescope (mm)

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

Eyepiece (mm)

For example, to determine the magnification of the 80ED with a 20mm eyepiece, divide the focal length of the spotting scope

(600mm) by the focal length of the eyepiece (20mm). 600 divided by 20 yields 30 power.

Although the power is variable, each instrument has a limit to the highest useful magnification. The general rule is that 60 power can be used for every inch of aperture. For example, in a 3.2” diameter telescope, such as the 80ED, the maximum useful magnification is 192 power. This is derived from multiplying 60 times 3.2”. Although this is the maximum useful

magnifica

tion, most observing is done in the range of 20 to 35 power for every inch of aperture which for the 80ED is 64 to

112.

Determining Field of View

Determining the field of view is important if you want to get an idea of the angular size of the object you are observing. To calculate the actual field of view, divide the apparent field of the eyepiece (supplied by the eyepiece manufacturer) by the magnification. In equation format, the formula looks like this:

Apparent Field of Eyepiece

True Field = ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

Magnification

As you can see, before determining the field of view, you must calculate the magnification. Using the example in the previous section, we can determine the field of view using the same 20mm eyepiece. The 20mm eyepiece has an apparent field of view of

50°. Divide the 50° by the magnification, which is 30 power. This yields an actual field of 1.67°.

To convert degrees to feet at 1,000 yards, which is more useful for terrestrial observing, simply multiply by 52.5. Continuing with our example , multiply the angular field 1.67

° by 52.5. This produces a linear field width of 87.7

feet at a distance of one thousand yards. The apparent field of each eyepiece that Celestron manufactures is found in the Celestron Accessory Catalog

(#93685).

General Observing Hints

When working with any optical instrument, there are a few things to remember to ensure you get the best possible image.

•

Never look through window glass. Glass found in household windows is optically imperfect, and as a result, may vary in thickness from one part of a window to the next. This inconsistency can and will affect the ability to focus your telescope.

In most cases you will not be able to achieve a truly sharp image, while in some cases, you may actually see a double image.

•

Never look across or over objects that are producing heat waves. This includes asphalt parking lots on hot summer days or building rooftops.

•

Hazy skies, fog, and mist can also make it difficult to focus when viewing terrestrially. The amount of detail seen under these conditions is greatly reduced. Also, when photographing under these conditions, the processed film may come out a little grainier than normal with lower contrast and underexposed.

•

If you wear corrective lenses (specifically glasses), you may want to remove them when observing with an eyepiece attached to the telescope. When using a camera, however, you should always wear corrective lenses to ensure the sharpest possible focus. If you have astigmatism, corrective lenses must be worn at all times.

Up to this point, this manual covered the assembly and basic operation of your telescope. However, to understand your telescope more thoroughly, you need to know a little about the night sky. This section deals with observational astronomy in general and includes information on the night sky and polar alignment.

The Celestial Coordinate System

To help find objects in the sky, astronomers use a celestial coordinate system that is similar to our geographical coordinate system here on Earth. The celestial coordinate system has poles, lines of longitude and latitude, and an equator. For the most part, these remain fixed against the background stars.

The celestial equator runs 360 degrees around the Earth and separates the northern celestial hemisphere from the southern. Like the Earth's equator, it bears a reading of zero degrees. On Earth this would be latitude. However, in the sky this is referred to as declination, or DEC for short. Lines of declination are named for their angular distance above and below the celestial equator. The lines are broken down into degrees, minutes of arc, and seconds of arc.

Declination readings south of the equator carry a minus sign (-) in front of the coordinate and those north of the celestial equator are either blank (i.e., no designation) or preceded by a plus sign (+).

The celestial equivalent of longitude is called Right Ascension, or R.A. for short. Like the Earth's lines of longitude, they run from pole to pole and are evenly spaced 15 degrees apart. Although the longitude lines are separated by an angular distance, they are also a measure of time. Each line of longitude is one hour apart from the next. Since the

Earth rotates once every 24 hours, there are 24 lines total. As a result, the R.A. coordinates are marked off in units of time. It begins with an arbitrary point in the constellation of Pisces designated as 0 hours, 0 minutes, 0 seconds. All other points are designated by how far (i.e., how long) they lag behind this coordinate after it passes overhead moving toward the west.

Figure 5-1

The celestial sphere seen from the outside showing R.A. and DEC .

Motion of the Stars

The daily motion of the Sun across the sky is familiar to even the most casual observer. This daily trek is not the Sun moving as early astronomers thought, but the result of the Earth's rotation. The Earth's rotation also causes the stars to do the same, scribing out a large circle as the Earth completes one rotation. The size of the circular path a star follows depends on where it is in the sky. Stars near the celestial equator form the largest circles rising in the east and setting in the west. Moving toward the north celestial pole, the point around which the stars in the northern hemisphere appear to rotate, these circles become smaller. Stars in the mid-celestial latitudes rise in the northeast and set in the northwest.

Stars at high celestial latitudes are always above the horizon, and are said to be circumpolar because they never rise and never set. You will never see the stars complete one circle because the sunlight during the day washes out the starlight.

However, part of this circular motion of stars in this region of the sky can be seen by setting up a camera on a tripod and opening the shutter for a couple hours. The processed film will reveal semicircles that revolve around the pole.

(This description of stellar motions also applies to the southern hemisphere except all stars south of the celestial equator move around the south celestial pole.)

Figure 5-2

All stars appear to rotate around the celestial poles. However, the appearance of this motion varies depending on where you are looking in the sky. Near the north celestial pole the stars scribe out recognizable circles centered on the pole (1). Stars near the celestial equator also follow circular paths around the pole. But, the complete path is interrupted by the horizon.

These appear to rise in the east and set in the west (2). Looking toward the opposite pole, stars curve or arc in the opposite direction scribing a circle around the opposite pole (3).

Latitude Scales

The easiest way to polar align a telescope is with a latitude scale. Unlike other methods that require you to find the celestial pole by identifying certain stars near it, this method works off of a known constant to determine how high the polar axis should be pointed. The Advanced Series mount can be adjusted from 30 to 60 degrees (see figure 5-3).

The constant, mentioned above, is a relationship between your latitude and the angular distance the celestial pole is above the northern (or southern) horizon; The angular distance from the northern

Latitude

Scale horizon to the north celestial pole is always equal to your latitude. To illustrate this, imagine that you are standing on the north pole, latitude +90°. The north celestial pole, which has a declination of +90°, would be directly overhead (i.e., 90 above the horizon). Now, let’s say that you move one degree south — your latitude is now +89° and the celestial pole is no longer directly overhead. It has moved one degree closer

Figure 5-3 toward the northern horizon. This means the pole is now 89° above the northern horizon. If you move one degree further south, the same thing happens again. You would have to travel 70 miles north or south to change your latitude by one degree. As you can see from this example, the distance from the northern horizon to the celestial pole is always equal to your latitude.

If you are observing from Los Angeles, which has a latitude of 34°, then the celestial pole is 34° above the northern horizon. All a latitude scale does then is to point the polar axis of the telescope at the right elevation above the northern

(or southern) horizon. To align your telescope:

1. Make sure the polar axis of the mount is pointing due north. Use a landmark that you know faces north.

2. Level the tripod. There is a bubble level built into the mount for this purpose.

NOTE: Leveling the tripod is only necessary if using this method of polar alignment. Perfect polar alignment is still possible using other methods described later in this manual without leveling the tripod.

3. Adjust the mount in altitude until the latitude indicator points to your latitude. Moving the mount affects the angle the polar axis is pointing. For specific information on adjusting the equatorial mount, please see the section “Adjusting the

Mount.”

This method can be done in daylight, thus eliminating the need to fumble around in the dark. Although this method does NOT put you directly on the pole, it will limit the number of corrections you will make when tracking an object.

It will also be accurate enough for short exposure prime focus planetary photography (a couple of seconds) and short exposure piggyback astrophotography (a couple of minutes).

Pointing at Polaris

This method utilizes Polaris as a guidepost to the celestial pole. Since Polaris is less than a degree from the celestial pole, you can simply point the polar axis of your telescope at Polaris. Although this is by no means perfect alignment, it does get you within one degree. Unlike the previous method, this must be done in the dark when Polaris is visible.

1. Set the telescope up so that the polar axis is pointing north.

2. Loosen the DEC clutch knob and move the telescope so that the tube is parallel to the polar axis. When this is done, the declination setting circle will read +90°. If the declination setting circle is not aligned, move the telescope so that the tube is parallel to the polar axis.

3. Adjust the mount in altitude and/or azimuth until Polaris is in the field of view of the finder.

4. Center Polaris in the field of the telescope using the fine adjustment controls on the mount.

Remember, while Polar aligning, do NOT move the telescope in R.A. or DEC. You do not want to move the

telescope itself, but the polar axis. The telescope is used simply to see where the polar axis is pointing.

Like the previous method, this gets you close to the pole but not directly on it. The following methods help improve your accuracy for more serious observations and photography.

Finding the North Celestial Pole

In each hemisphere, there is a point in the sky around which all the other stars appear to rotate. These points are called the celestial poles and are named for the hemisphere in which they reside. For example, in the northern hemisphere all stars move around the north celestial pole. When the telescope's polar axis is pointed at the celestial pole, it is parallel to the Earth's rotational axis.

Definition

Many methods of polar alignment require that you know how to find the celestial pole by identifying stars in the area. For those in the northern hemisphere, finding the celestial pole is not too difficult. Fortunately, we have a naked eye star less than a degree away. This star,

Polaris, is the end star in the handle of the Little Dipper. Since the Little Dipper (technically called Ursa Minor) is not one of the brightest constellations in the sky, it may be difficult to locate from urban areas. If this is the case, use the two end stars in the bowl of the Big Dipper

(the pointer stars). Draw an imaginary line through them toward the Little Dipper. They point to Polaris (see Figure 5-5). The position of the Big Dipper changes during the year and throughout the course of the night (see Figure 5-4). When the Big Dipper is low in the sky

(i.e., near the horizon), it may be difficult to locate. During these times, look for Cassiopeia

(see Figure 5-5). Observers in the southern hemisphere are not as fortunate as those in the northern hemisphere. The stars around the south celestial pole are not nearly as bright as those around the north. The closest star that is relatively bright is Sigma Octantis. This star is just within naked eye limit (magnitude 5.5) and lies about 59 arc minutes from the pole. Figure 5-4 The position of the

Big Dipper changes throughout the year and the night.

The north celestial pole is the point in the northern hemisphere around which all stars appear to rotate. The counterpart in the southern hemisphere is referred to as the south celestial pole.

Figure 5-5

The two stars in the front of the bowl of the Big Dipper point to Polaris which is less than one degree from the true (north) celestial pole. Cassiopeia, the “W” shaped constellation, is on the opposite side of the pole from the Big Dipper. The North

Celestial Pole (N.C.P.) is marked by the “+” sign.

D e c l i i n a t t i i o n D r r i i f f t t M e t t h o d o f f P o l l a r r A l i i g n m e n t t

This method of polar alignment allows you to get the most accurate alignment on the celestial pole and is required if you want to do long exposure deep-sky astrophotography through the telescope. The declination drift method requires that you monitor the drift of selected stars. The drift of each star tells you how far away the polar axis is pointing from the true celestial pole and in what direction. Although declination drift is simple and straight-forward, it requires a great deal of time and patience to complete when first attempted. The declination drift method should be done after any one of the previously mentioned methods has been completed.

To perform the declination drift method you need to choose two bright stars. One should be near the eastern horizon and one due south near the meridian. Both stars should be near the celestial equator (i.e., 0° declination). You will monitor the drift of each star one at a time and in declination only. While monitoring a star on the meridian, any misalignment in the east-west direction is revealed. While monitoring a star near the east/west horizon, any misalignment in the north-south direction is revealed. It is helpful to have an illuminated reticle eyepiece to help you recognize any drift. For very close alignment, a Barlow lens is also recommended since it increases the magnification and reveals any drift faster. When looking due south, insert the diagonal so the eyepiece points straight up. Insert the cross hair eyepiece and align the cross hairs so that one is parallel to the declination axis and the other is parallel to the right ascension axis. Move your telescope manually in R.A. and DEC to check parallelism.

First, choose your star near where the celestial equator and the meridian meet. The star should be approximately within

1/2 an hour of the meridian and within five degrees of the celestial equator. Center the star in the field of your telescope and monitor the drift in declination.

• If the star drifts south, the polar axis is too far east.

• If the star drifts north, the polar axis is too far west.

Make the appropriate adjustments to the polar axis to eliminate any drift. Once you have eliminated all the drift, move to the star near the eastern horizon. The star should be 20 degrees above the horizon and within five degrees of the celestial equator.

• If the star drifts south, the polar axis is too low.

• If the star drifts north, the polar axis is too high.

Again, make the appropriate adjustments to the polar axis to eliminate any drift. Unfortunately, the latter adjustments interact with the prior adjustments ever so slightly. So, repeat the process again to improve the accuracy checking both axes for minimal drift. Once the drift has been eliminated, the telescope is very accurately aligned. You can now do prime focus deep-sky astrophotography for long periods.

NOTE: If the eastern horizon is blocked, you may choose a star near the western horizon, but you must reverse the polar high/low error directions. Also, if using this method in the southern hemisphere, the direction of drift is reversed for both R.A. and DEC.

With your telescope set up, you are ready to use it for observing. This section covers visual observing hints for both solar system and deep sky objects as well as general observing conditions which will affect your ability to observe.

Observing the Moon

Often, it is tempting to look at the Moon when it is full. At this time, the face we see is fully illuminated and its light can be overpowering.

In addition, little or no contrast can be seen during this phase.

One of the best times to observe the Moon is during its partial phases

(around the time of first or third quarter). Long shadows reveal a great amount of detail on the lunar surface. At low power you will be able to see most of the lunar disk at one time. Change to higher power

(magnification) to focus in on a smaller area. Choose the lunar tracking rate from the hand control's MENU tracking rate options to keep the moon centered in the eyepiece even at high magnifications.

Lunar Observing Hints

To increase contrast and bring out detail on the lunar surface, use filters. A yellow filter works well at improving contrast while a neutral density or polarizing filter will reduce overall surface brightness and glare.

Observing the Planets

Other fascinating targets include the five naked eye planets. You can see Venus go through its lunar-like phases. Mars can reveal a host of surface detail and one, if not both, of its polar caps. You will be able to see the cloud belts of Jupiter and the great Red Spot (if it is visible at the time you are observing). In addition, you will also be able to see the moons of Jupiter as they orbit the giant planet. Saturn, with its beautiful rings, is easily visible at moderate power.

Planetary Observing Hints

• Remember that atmospheric conditions are usually the limiting factor on how much planetary detail will be visible.

So, avoid observing the planets when they are low on the horizon or when they are directly over a source of radiating heat, such as a rooftop or chimney. See the "Seeing Conditions" section later in this section.

• To increase contrast and bring out detail on the planetary surface, try using Celestron eyepiece filters.

Observing the Sun

Although overlooked by many amateur astronomers, solar observation is both rewarding and fun. However, because the Sun is so bright, special precautions must be taken when observing our star so as not to damage your eyes or your telescope.

Never project an image of the Sun through the telescope. Because of the folded optical design, tremendous heat buildup will result inside the optical tube. This can damage the telescope and/or any accessories attached to the telescope.

For safe solar viewing, use a solar filter that reduces the intensity of the Sun's light, making it safe to view. With a filter you can see sunspots as they move across the solar disk and faculae, which are bright patches seen near the Sun's edge.

Solar Observing Hints

• The best time to observe the Sun is in the early morning or late afternoon when the air is cooler.

• To center the Sun without looking into the eyepiece, watch the shadow of the telescope tube until it forms a circular shadow.

•

To ensure accurate tracking, be sure to select the solar tracking rate.

Observing Deep Sky Objects

Deep-sky objects are simply those objects outside the boundaries of our solar system. They include star clusters, planetary nebulae, diffuse nebulae, double stars and other galaxies outside our own Milky Way. Most deep-sky objects have a large angular size. Therefore, low-to-moderate power is all you need to see them. Visually, they are too faint to reveal any of the color seen in long exposure photographs. Instead, they appear black and white. And, because of their low surface brightness, they should be observed from a dark-sky location. Light pollution around large urban areas washes out most nebulae making them difficult, if not impossible, to observe. Light Pollution Reduction filters help reduce the background sky brightness, thus increasing contrast.

Seeing Conditions

Viewing conditions affect what you can see through your telescope during an observing session. Conditions include transparency, sky illumination, and seeing. Understanding viewing conditions and the effect they have on observing will help you get the most out of your telescope.

Transparency

Transparency is the clarity of the atmosphere which is affected by clouds, moisture, and other airborne particles. Thick cumulus clouds are completely opaque while cirrus can be thin, allowing the light from the brightest stars through.

Hazy skies absorb more light than clear skies making fainter objects harder to see and reducing contrast on brighter objects. Aerosols ejected into the upper atmosphere from volcanic eruptions also affect transparency. Ideal conditions are when the night sky is inky black.

Sky Illumination

General sky brightening caused by the Moon, aurorae, natural airglow, and light pollution greatly affect transparency.

While not a problem for the brighter stars and planets, bright skies reduce the contrast of extended nebulae making them difficult, if not impossible, to see. To maximize your observing, limit deep sky viewing to moonless nights far from the light polluted skies found around major urban areas. LPR filters enhance deep sky viewing from light polluted areas by blocking unwanted light while transmitting light from certain deep sky objects. You can, on the other hand, observe planets and stars from light polluted areas or when the Moon is out.

Seeing

Seeing conditions refers to the stability of the atmosphere and directly affects the amount of fine detail seen in extended objects. The air in our atmosphere acts as a lens which bends and distorts incoming light rays. The amount of bending depends on air density. Varying temperature layers have different densities and, therefore, bend light differently. Light rays from the same object arrive slightly displaced creating an imperfect or smeared image. These atmospheric

disturbances vary from time-to-time and place-to-place. The size of the air parcels compared to your aperture determines the "seeing" quality. Under good seeing conditions, fine detail is visible on the brighter planets like Jupiter and Mars, and stars are pinpoint images. Under poor seeing conditions, images are blurred and stars appear as blobs.

The conditions described here apply to both visual and photographic observations.

Figure 6-1

Seeing conditions directly affect image quality. These drawings represent a point source (i.e., star) under bad seeing conditions (left) to excellent conditions

(right). Most often, seeing conditions produce images that lie some where between these two extremes.

After looking at the night sky for a while you may want to try photographing it. Several forms of photography are possible with your telescope, including terrestrial and celestial photography. Both of these are discussed in moderate detail with enough information to get you started. Topics include the accessories required and some simple techniques.

More information is available in some of the publications listed at the end of this manual.

In addition to the specific accessories required for each type of celestial photography, there is the need for a camera - but not just any camera. The camera does not have to have many of the features offered on today's state-of-the-art equipment. For example, you don't need auto focus capability or mirror lock up. Here are the mandatory features a camera needs for celestial photography. First, a “B” setting which allows for time exposures. This excludes point and shoot cameras and limits the selection to SLR cameras, the most common type of 35mm camera on the market today.

Second, the “B” or manual setting should NOT run off the battery. Many new electronic cameras use the battery to keep the shutter open during time exposures. Once the batteries are drained, usually after a few minutes, the shutter closes, whether you were finished with the exposure or not. Look for a camera that has a manual shutter when operating in the time exposure mode. Olympus, Nikon, Minolta, Pentax, Canon and others have made such camera bodies.

The camera must have interchangeable lenses so you can attach it to the telescope and so you can use a variety of lenses for piggyback photography. If you can't find a new camera, you can purchase a used camera body that is not

100-percent functional. The light meter, for example, does not have to be operational since you will be determining the exposure length manually.

You also need a cable release with a locking function to hold the shutter open while you do other things. Mechanical and air release models are available.

P i i g g y b a c k

The easiest way to enter the realm of deep-sky, long exposure astrophotography is via the piggyback method. Piggyback photography is done with a camera and its normal lens riding on top of the telescope.

Through piggyback photography you can capture entire constellations and record large scale nebulae that are too big for prime focus photography. Because you are photographing with a low power lens and guiding with a high power telescope, the margin for error is very large. Small mistakes made while guiding the telescope will not show up on film. To attach the camera to the telescope, use the piggyback adapter screw located on the top of the tube mounting ring. It may be necessary to remove the finder scope bracket before attaching the camera.

As with any form of deep-sky photography, it should be done from a dark sky observing site. Light pollution around major urban areas washes out the faint light of deep-sky objects. You can still practice from less ideal skies.

1. Polar align the telescope (using one of the methods described earlier) and start the motor drive.

2. Load your camera with slide film, ISO 100 or faster, or print film, ISO 400 or faster!

3. Set the f/ratio of your camera lens so that it is a half stop to one full stop down from completely open.

4. Set the shutter speed to the “B” setting and focus the lens to the infinity setting.

5. Locate the area of the sky that you want to photograph and move the telescope so that it points in that direction.

6. Find a suitable guide star in the telescope eyepiece field of view. This is relatively easy since you can search a wide area without affecting the area covered by your camera lens. If you do not have an illuminated cross hair eyepiece for guiding, simply defocus your guide star until it fills most of the field of view. This makes it easy to detect any drift.

7. Release the shutter using a cable release.

8. Monitor your guide star for the duration of the exposure making the necessary corrections needed to keep the star centered.

Short Exposure Prime Focus Photography

Short exposure prime focus photography is the best way to begin recording celestial objects. It is done with the camera attached to the telescope without an eyepiece or camera lens in place. To attach your camera, you need the T-adapter and a T-Ring for your specific camera (i.e., Minolta, Nikon, Pentax, etc.). The focuser has a built-in T-adapter and are ready to accept a 35mm camera body. The T-Ring replaces the

35mm SLR camera’s normal lens. Prime focus photography allows you to capture the entire solar disk (if using the proper filter) as well as the entire lunar disk. To attach your camera to your telescope:

1 Remove the eyepiece from the 1 1 /

" eyepiece holder. the /

" eyepiece holder from the focuser assembly. This will expose the male thread of the builtin T-adapter.

3 Thread the T-ring onto the exposed T-adapter threads.

4 Mount your camera body onto the T-Ring the same as you would any other lens.

With your camera attached to the telescope, you are ready for prime focus photography. Start with an easy object like the Moon. Here’s how to do it:

1. Load your camera with film that has a moderate-to-fast speed (i.e., ISO rating). Faster films are more desirable when the Moon is a crescent. When the Moon is near full, and at its brightest, slower films are more desirable. Here are some film recommendations:

• T-Max 100

• T-Max 400

• Any 100 to 400 ISO color slide film

• Fuji Super HG 400

2. Center the Moon in the field of your telescope.

3. Focus the telescope by turning the focus knob until the image is sharp.

4. Set the shutter speed to the appropriate setting (see table 7-1).

5. Trip the shutter using a cable release.

6. Advance the film and repeat the process.

Lunar Phase

Crescent

Quarter

Full

ISO 50 ISO 100 ISO 200 ISO 400

Table 7-1

Above is a listing of recommended exposure times when photographing the Moon at the prime focus of your telescope.

The exposure times listed in table 7-1 should be used as a starting point. Always make exposures that are longer and shorter than the recommended time. Also, take a few photos at each shutter speed. This will ensure that you will get a good photo.

•

If using black and white film, try a yellow filter to reduce the light intensity and to increase contrast.

Keep accurate records of your exposures. This information is useful if you want to repeat your results or if you want to submit some of your photos to various astronomy magazines for possible publication!

• This technique is also used for photographing the Sun with the proper solar filter.

Terrestrial Photography

Your telescope makes an excellent telephoto lens for terrestrial (land) photography. Terrestrial photography is best done will the telescope tracking drive turned off. To turn the tracking drive off, press the MENU (9) button on the hand control and scroll down to the Tracking Mode sub menu. Use the Up and Down scroll keys (10) to select the Off option and press ENTER. This will turn the tracking motors off, so that objects will remain in your camera's field of view.

Metering

The Advanced Series telescope has a fixed aperture and, as a result, fixed f/ratios. To properly expose your subjects photographically, you need to set your shutter speed accordingly. Most 35mm SLR cameras offer through-the-lens metering which lets you know if your picture is under or overexposed. Adjustments for proper exposures are made by changing the shutter speed. Consult your camera manual for specific information on metering and changing shutter speeds.

Reducing Vibration

Releasing the shutter manually can cause vibrations, producing blurred photos. To reduce vibration when tripping the shutter, use a cable release. A cable release keeps your hands clear of the camera and lens, thus eliminating the possibility of introducing vibration. Mechanical shutter releases can be used, though air-type releases are best.

Blurry pictures can also result from shutter speeds that are too slow. To prevent this, use films that produce shutter speeds greater than 1/250 of a second when hand-holding the lens. If the lens is mounted on a tripod, the exposure length is virtually unlimited.

Another way to reduce vibration is with the Vibration Suppression Pads (#93503).

These pads rest between the ground and tripod feet. They reduce the vibration amplitude and vibration time.

Auto Guiding

The Advanced GT telescope has a designated auto guiding port for use with a CCD autoguider. The diagram below may be useful when connecting the CCD camera cable to the telescope and calibrating the autoguider. Note that the four outputs are active-low, with internal pull-ups and are capable of sinking 25 mA DC.

While your telescope requires little maintenance, there are a few things to remember that will ensure your telescope performs at its best.

C a r r e a n d C l l e a n i i n g o f f t t h e O p t t i i c s

Occasionally, dust and/or moisture may build up on the objective lens of your telescope. Special care should be taken when cleaning any instrument so as not to damage the optics.

If dust has built up on the lens, remove it with a brush (made of camel’s hair) or a can of pressurized air. Spray at an angle to the lens for approximately two to four seconds. Then, use an optical cleaning solution and white tissue paper to remove any remaining debris. Apply the solution to the tissue and then apply the tissue paper to the lens. Low pressure strokes should go from the center of the lens to the outer portion. Do NOT rub in circles!

You can use a commercially made lens cleaner or mix your own. A good cleaning solution is isopropyl alcohol mixed with distilled water. The solution should be 60% isopropyl alcohol and 40% distilled water. Or, liquid dish soap diluted with water (a couple of drops per one quart of water) can be used.

Occasionally, you may experience dew build-up on the lens of your telescope during an observing session. If you want to continue observing, the dew must be removed, either with a hair dryer (on low setting) or by pointing the telescope at the ground until the dew has evaporated.

If moisture condenses on the inside of the lens, remove the accessories from the rear cell of the telescope. Place the telescope in a dust-free environment and point it down. This will remove the moisture from the telescope tube.

To minimize the need to clean your telescope, replace all lens covers once you have finished using it. Since the rear cell is NOT sealed, the cover should be placed over the opening when not in use. This will prevent contaminants from entering the optical tube.

Internal adjustments and cleaning should be done only by the Celestron repair department. If your telescope is in need of internal cleaning, please call the factory for a return authorization number and price quote.

You will find that additional accessories enhance your viewing pleasure and expand the usefulness of your telescope. For ease of reference, all the accessories are listed in alphabetical order.

Auxiliary Port Accessory (#93965) – This accessory plugs into the auxiliary port of the telescopes control panel to provide additional ports for accessories like the CN-16 GPS as well as a PC programming port.

Barlow Lens - A Barlow lens is a negative lens that increases the focal length of a telescope. Used with any eyepiece, it doubles the magnification of that eyepiece. Celestron offers two Barlow lens in the 1-1/4" size. The 2x Ultima Barlow

(#93506) is a compact triplet design that is fully multicoated for maximum light transmission and parfocal when used with

• the Ultima eyepieces. The OMNI Barlow (#93326) is a compact achromatic Barlow lens that is under three inches long and weighs only 4 oz. It works very well with all Celestron eyepieces.

Eyepieces - Like telescopes, eyepieces come in a variety of designs. Each design has its own advantages and disadvantages. For the 1-1/4" barrel diameter there are four different eyepiece designs available.

• OMNI Plössl -

Plössl eyepieces have a 4-element lens designed for low-to-high power observing. The Plössls offer razor sharp views across the entire field, even at the edges! In the 1-1/4" barrel diameter, they are available in the following focal lengths: 4mm, 6mm, 9mm, 12.5mm, 15mm, 20mm, 25mm, 32mm and

40mm.

X-Cel -

This 6 element design allows each X-Cel Eyepiece to have 20mm of eye relief, 55° field of view and more than 25mm of lens aperture (even with the 2.3mm). In order to maintain razor sharp, color corrected images across its 55° field of view, extra-low dispersion glass is used for the most highly curved optical elements. The excellent refractive properties of these high grade optical elements, make the X-Cel line especially well suited for high magnification planetary viewing where sharp, color-free views are most appreciated. X-Cel eyepiece come in the following focal lengths: 2.3mm, 5mm, 8mm,

10mm, 12.5mm, 18mm, 21mm, 25mm.

• Ultima - Ultima is our 5-element, wide field eyepiece design. In the 1-1/4" barrel diameter, they are available in the following focal lengths: 5mm, 7.5mm, 10mm, 12.5mm, 18mm,

30mm, 35mm, and 42mm. These eyepieces are all parfocal. The 35mm Ultima gives the widest possible field of view with a 1-1/4" diagonal.

• Axiom –

As an extension of the Ultima line, a new wide angle series is offered – called the Axiom series. All units are seven element designs and feature a 70º extra wide field of view (except the 50mm). All are fully multicoated and contain all the features of the Ultimas.

Filters Sets , Eyepiece - Celestron offers four convenient filter sets, which contain four different filters per set. Not only are these highly useful filter combinations, but they also offer an economical way to add versatility to your filter collection.

Series 1 – #94119-10

Orange, Light Blue, ND13%T, Polarizing (#s 21, 80A, #15, Polarizing)

Series 2 – #94119-20

Deep Yellow, Red, Light Green, ND25% T (#s 12, 25, 56, 96ND-25)

Series 3 – #94119-30

Light Red, Blue, Green, ND50% T (#s 23A, 38A, 58, 96ND-50)

Series 4 – #94119-40

Yellow, Deep Yellow, Violet, Pale Blue (#s 8, 47, 82A, 96ND-13)

Flashlight , Night Vision - (#93588) - Celestron’s premium model for astronomy, using two red LED ' s to preserve night vision better than red filters or other devices. Brightness is adjustable. Operates on a single 9 volt battery (included).

CN16 GPS Accessory (#93963 ) - Plug in this 16-channel GPS module into your telescopes drive base port to link up and automatically download information from one of many global positioning satellites. Controlled with the computerized hand control, the CN-16 will greatly improve the accuracy of your star alignments.

CN16 GPS Bracket (#93964 ) – Support your CN-16 GPS accessory with this bracket and strap combination that securely wraps around any of the tripod legs and holds the GPS module in place .

Diagonal 2" Mirror (#93519) - Celestron offers a 2" 90° Mirror Diagonal to thread on Schmidt- Cassegrain telescopes or slides into the barrel of a 2" focuser. This diagonal includes an adapter to accept 1¼" eyepieces. It has a multicoated mirror and smooth mechanics that are precision manufactured for reliability

Light Pollution Reduction (LPR) Filters (#94126A) - These filters are designed to enhance your views of deep sky astronomical objects when viewed from urban areas. LPR Filters selectively reduce the transmission of certain wavelengths of light, specifically those produced by artificial lights. This includes mercury and high and low pressure sodium vapor lights. In addition, they also block unwanted natural light (sky glow) caused by neutral oxygen emission in our atmosphere.

Micro Guide Eyepiece (#94171) - This multipurpose 12.5mm illuminated reticle can be used for guiding deep-sky astrophotos, measuring position angles, angular separations, and more. The laser etched reticle provides razor sharp lines and the variable brightness illuminator is completely cordless.

Moon Filter ( # 94119-A) - Celestron’s Moon Filter is an economical eyepiece filter for reducing the brightness of the moon and improving contrast, so greater detail can be observed on the lunar surface. The clear aperture is 21mm and the transmission is about 18%.

Motor Drive, Dual Axis (#93523) - This dual axis motor drive, with drive corrector capabilities, are designed for

Celestron's Advanced CG-5 mounts. They precisely control the telescope's tracking speed during long, timed exposures of celestial objects, producing the best possible image sharpness. Four speeds are available—1x (sidereal), 2x for guiding, 4x, and 8x for centering. These precision, state-of-the-art DC motor drives operate from 4 D-cell batteries (not included). The hand controller module is very compact and fits easily in the palm of your hand. Motors for both axes are included, along with brackets, clutches and hardware. For non-computerized Advanced Series Mounts.

Polar Axis Finderscope (#94220) – This useful accessory speeds accurate polar alignment by providing a means of visually aligning your German equatorial mount with Polaris and true north. As a result, you can spend more time observing and less time setting up. The finderscope has an easy to use cross hair reticle.

PowerTank (#18774) – 12v 7Amp hour rechargeable power supply. Comes with two 12v output cigarette outlets, built-in red flash light , Halogen emergency spotlight. Switchable

110v/220v AC adapter and cigarette lighter adapter included.

RS-232 Cable (#93920) – Allows your Advanced Series telescope to be controlled using a laptop computer or PC. Once connected, the telescope can be controlled using popular astronomy software programs.

Sky Map s (#93722) - Celestron Sky Maps are the ideal teaching guide for learning the night sky. You wouldn’t set off on a road trip without a road map, and you don’t need to try to navigate the night sky without a map either. E ven if you already know your way around the major constellations, these maps can help you locate all kinds of fascinating objects.

T-Ring - The T-Ring couples your 35mm SLR camera body to the T-Adapter, radial guider, or tele-extender. This accessory is mandatory if you want to do photography through the telescope. Each camera make (i.e., Minolta, Nikon,

Pentax, etc.) has its own unique mount and therefore, its own T-Ring. Celestron has 8 different models for 35mm cameras.

A full description of all Celestron accessories can be found in the Celestron Accessory Catalog (#93685)

Appendix A – Technical Specifications

Advanced Series 21021 / 21022 21026 / 21027

Specifications:

Optical Design

Focal Length

Finderscope

Mount

Eyepiece

Accessory tray

Tripod

80mm (3.2") refractor

600mm F/7.5

100mm (4") refractor

900mm F/9

6x30 9x50

CG-5 Equatorial

20mm – 1.25" (30x)

Yes

2" Stainless Steel

CG-5 Equatorial

20mm – 1.25" (45x)

Yes

2" Stainless Steel

Technical Specs

Highest Useful Magnification

Lowest Useful Magnification

Limiting Stellar Magnitude

Resolution: Rayleigh

Dawes Limit

Light Gathering Power

Field of View: standard eyepiece

Linear FOV (@1000 yds)

Optical Coatings - Standard

Optical tube length

Telescope Weight

189x 236x

11x 14x

12 12.5

1.73 arc seconds

1.45 arc seconds

131x unaided eye

1.38 arc seconds

1.16 arc seconds

204x unaided eye

1.67º 1.3º

87.5 ft 70 ft

Fully Multi-Coated Fully Multi-Coated

23" 34"

42 lbs 50 lbs

Advanced GT

Additional Specifications

Hand Control

Motor: Type

Max Slew Speed

Software Precision

Hand Control Ports

Motor Ports

Tracking Rates

Tracking Modes

Alignment Procedures

Database

Complete Revised NGC Catalog

Complete Messier Catalog

Complete IC Catalog

Complete Caldwell

Abell Galaxies

Solar System objects

Famous Asterisms

Selected CCD Imaging Objects

Selected SAO Stars

Total Object Database

7,840

110

5,386

109

2,712

29,500

45,492

Double line, 16 character Liquid Crystal Display; 19 fiber optic backlit LED buttons

DC Servo motors with encoders, both axes

3º/second

24bit, 0.08 arc sec calculation

RS-232 communication port on hand control

Aux Port, Autoguide Ports

Sidereal, Solar and Lunar

EQ North & EQ South

AutoAlign, 3-Star Alignment, Quick Align, Last Align

40,000+ objects, 400 user defined programmable objects.

Enhanced information on over 200 objects

Appendix B - Glossary of Terms

A-

Absolute magnitude

Airy disk

Alt-Azimuth Mounting

Altitude

Aperture

Apparent Magnitude

Arcminute

Arcsecond

Asterism

Asteroid

The apparent magnitude that a star would have if it were observed from a standard distance of 10 parsecs, or 32.6 light-years.

The absolute magnitude of the Sun is 4.8. at a distance of 10 parsecs, it would just be visible on Earth on a clear moonless night away from surface light.

The apparent size of a star's disk produced even by a perfect optical system. Since the star can never be focused perfectly, 84 per cent of the light will concentrate into a single disk, and 16 per cent into a system of surrounding rings.

A telescope mounting using two independent rotation axis allowing movement of the instrument in

Altitude and Azimuth.

In astronomy, the altitude of a celestial object is its Angular Distance above or below the celestial horizon. the diameter of a telescope's primary lens or mirror; the larger the aperture, the greater the telescope 's light-gathering power.

A measure of the relative brightness of a star or other celestial object as perceived by an observer on

Earth.

A unit of angular size equal to 1/60 of a degree.

A unit of angular size equal to 1/3,600 of a degree (or 1/60 of an arcminute).

A small unofficial grouping of stars in the night sky.

A small, rocky body that orbits a star.

Astrology T he pseudoscientific belief that the positions of stars and planets exert an influence on human affairs; astrology has nothing in common with astronomy .

Astronomical unit (AU) The distance between the Earth and the Sun. It is equal to 149,597,900 km., usually rounded off to

150,000,000 km.

Aurora

Azimuth

T he emission of light when charged particles from the solar wind slam s into and excite s atoms and molecul es in a planet' s upper atmosphere.

The angular distance of an object eastwards along the horizon, measured from due north, between the astronomical meridian (the vertical line passing through the center of the sky and the north and south points on the horizon) and the vertical line containing the celestial body whose position is to be measured. .

B -

Binary Stars Binary (Double) stars are pairs of stars that, because of their mutual gravitational attracti on, orbit around a common Center of Mass. If a group of three or more stars revolve around one another, it is called a multiple system. It is believed that approximately 50 percent of all stars belong to binary or multiple systems. Systems with individual components that can be seen separately by a telescope are called visual binaries or visual multiples. The nearest "star" to our solar system, Alpha Centauri, is actually our nearest example of a multiple star system, it consists of three stars , two very similar to our Sun and one dim, small, red star orbiting around one another.

C -

Celestial Equator

Celestial pole

The projection of the Earth's equator on to the celestial sphere. It divides the sky into two equal hemispheres.

T h e imaginary projection of Earth 's rotational axis north or south pole onto the celestial sphere.

An imaginary sphere surrounding the Earth, concentric with the Earth's center. Celestial Sphere

Collimation

D -

The act of putting a telescope' s optics into perfect alignment.

Declination (DEC) The angular distance of a celestial body north or south of the celestial equator. It may be said to correspond to latitude on the surface of the Earth.

E -

Ecliptic

Equatorial mount

The projection of the Earth's orbit on to the celestial sphere. It may also be defined as "the apparent yearly path of the Sun against the stars".

A telescope mounting in which the instrument is set upon an axis which is parallel to the axis of the

Earth; the angle of the axis must be equal to the observer's latitude.

F -

Focal length The distance between a lens (or mirror) and the point at which the image of an object at infinity is brought to focus. The focal length divided by the aperture of the mirror or lens is termed the focal ratio.

J -

Jovian Planets Any of the four gas giant planets that are at a greater distance form the sun than the terrestrial planets.

K -

Kuiper Belt

L -

Light-Year (LY)

M -

Magnitude

Meridian

Messier

N -

Nebula

North Celestial Pole

Nova

O -

Open Cluster

P -

Parallax

Parfocal

Parsec

Point Source

R -

Reflector

Resolution

Right Ascension: (RA)

S -

Schmidt Telescope

Sidereal Rate

A region beyond the orbit of Neptune extending to about 1000 AU which is a source of many short period comets.

A light-year is the distance light traverses in a vacuum in one year at the speed of 299,792 km/ sec.

With 31,557,600 seconds in a year, the light-year equals a distance of 9.46 X 1 trillion km (5.87 X 1 trillion mi).

Magnitude is a measure of the brightness of a celestial body. The brightest stars are assigned magnitude 1 and those increasingly fainter from 2 down to magnitude 5. The faintest star that can be seen without a telescope is about magnitude 6. Each magnitude step corresponds to a ratio of 2.5 in brightness. Thus a star of magnitude 1 is 2.5 times brighter than a star of magnitude 2, and 100 times brighter than a magnitude 5 star. The brightest star, Sirius, has an apparent magnitude of -1.6, the full moon is -12.7, and the Sun's brightness, expressed on a magnitude scale, is -26.78. The zero point of the apparent magnitude scale is arbitrary.

A reference line in the sky that starts at the North celestial pole and ends at the South celestial pole and passes through the zenith. If you are facing South, the meridian starts from your Southern horizon and passes directly overhead to the North celestial pole.

A French astronomer in the late 1700’s who was primarily looking for comets. Comets are hazy diffuse objects and so Messier cataloged objects that were not comets to help his search. This catalog became the Messier Catalog, M1 through M110.

Interstellar cloud of gas and dust. Also refers to any celestial object that has a cloudy appearance.

The point in the Northern hemisphere around which all the stars appear to rotate. This is caused by the fact that the Earth is rotating on an axis that passes through the North and South celestial poles.

The star Polaris lies less than a degree from this point and is therefore refer r ed to as the "Pole Star".

Although Latin for "new" it denotes a star that suddenly becomes explosively bright at the end of its life cycle.

One of the groupings of stars that are concentrated along the plane of the Milky Way. Most have an asymmetrical appearance and are loosely assembled. They contain from a dozen to many hundred s of stars.

Parallax is the difference in the apparent position of an object against a background when viewed by an observer from two different locations. These positions and the actual position of the object form a triangle from which the apex angle (the parallax) and the distance of the object can be determined if the length of the baseline between the observing positions is known and the angular direction of the object from each position at the ends of the baseline has been measured. The traditional method in astronomy of determining the distance to a celestial object is to measure its parallax.

Refers to a group of eyepieces that all require the same distance from the focal plane of the telescope to be in focus. This means when you focus one parfocal eyepiece all the other parfocal eyepieces, in a particular line of eyepieces, will be in focus.

The distance at which a star would show parallax of one second of arc. It is equal to 3.26 light-years,

206,265 astronomical units, or 30,8000,000,000,000 km. (Apart from the Sun, no star lies within one parsec of us.)

An object which cannot be resolved into an image because it to too far away or too small is considered a point source. A planet is far away but it can be resolved as a disk. Most stars cannot be resolved as disks, they are too far away.

A telescope in which the light is collected by means of a mirror.

The minimum detectable angle an optical system can detect. Because of diffraction, there is a limit to the minimum angle, resolution. The larger the aperture, the better the resolution.

T he angular distance of a celestial object measured in hours, minutes, and seconds along the

Celestial Equator eastward from the Vernal Equinox.

Rated the most important advance in optics in 200 years, the Schmidt telescope combines the best features of the refractor and reflector for photographic purposes. It was invented in 1930 by

Bernhard Voldemar Schmidt (1879-1935).

This is the angular speed at which the Earth is rotating. Telescope tracking motors drive the

T -

Terminator

U -

Universe

V -

Variable Star

W -

Waning Moon

Waxing Moon

Z -

Zenith

Zodiac telescope at this rate. The rate is 15 arc seconds per second or 15 degrees per hour.

The boundary line between the light and dark portion of the moon or a planet.

The totality of astronomical things, events, relations and energies capable of being described objectively.

A star whose brightness varies over time due to either inherent properties of the star or something eclipsing or obscuring the brightness of the star.

The period of the moon's cycle between full and new, when its illuminated portion is decreasing.

The period of the moon's cycle between new and full, when its illuminated portion is increasing.

The point on the Celestial Sphere directly above the observer.

The zodiac is the portion of the Celestial Sphere that lies within 8 deg rees on either side of the

Ecliptic. The apparent paths of the Sun, the Moon, and the planets, with the exception of some portions of the path of Pluto, lie within this band. Twelve divisions, or signs, each 30 deg rees in width, comprise the zodiac. These signs coincided with the zodiacal constellations about 2,000 years ago. Because of the Precession of the Earth's axis, the Vernal Equinox has moved westward by about 30 deg rees since that time; the signs have moved with it and thus no longer coincide with the constellations.

A P P E N D I I X C

L O N G I I T U D E S A N D

L A T I I T U D E S

LONGITUDE LATITUDE

ALABAMA

degrees

Anniston min degrees min

85 51 33 34.8

Auburn 85 26.4 32 40.2

Birmingham 86 45 33 34.2

Centreville 87 15 32 54

Dothan 85 27 31 19.2

Fort 85 43.2 31 16.8

Gadsden 86 5.4 33 58.2

Huntsville 86 46.2 34 39

Castle AFB

China Lake

Crescent Cty

Mobile

88 15 30 40.8

Montgomery 86 2.4

30 37.8

32 18

Edwards AFB

El Centro

El Monte

El Toro Selma

Troy

86 59.4 32 20.4

86 1.2 31 52.2

Tuscaloosa 87 37.2 33 13.8

ALASKA

Fort Hunter

Fort Ord

LONGITUDE degrees

120

117

124

117

115

118

117

121

LATITUDE min degrees min

34.2

40.8

13.8

52.8

40.8

1.8

43.8

19.2

46.2

22.8

40.8

46.8

49.2

4.8

40.2

40.8

117 22.8 34 34.8 George AFB

Haines Hrbor 135 25.8 59 13.8

Imperial Bch

La Verne

Lake Tahoe

ARIZONA

Davis-M AFB

Deer Valley

Falcon Fld

110

112

111

52.8

4.8

43.8

Fort Huachuc

Gila Bend

110

113

10.2

GrandCanyon 112 9

10.2

40.8

28.2

35 57

Long Beach

Los Alamitos

Los Angeles

March AFB

Mather AFB

Miramar NAS

Moffet

117

120

7.2

46.8

118

117

121

2.4

16.2

1.8

117

122

34.2

49.2

46.8

55.8

52.8

34.2

52.2

25.2

LONGITUDE

Shelter Cove

degrees

124

LATITUDE min degrees

4.2 40 min

1.8

Superior Val 117 0.6 35 19.8

Travis AFB

Tustin Mcas

Van Nuys

COLORADO

Air Force A

121

117

118

55.8

49.8

28.8

105 21

16.2

13.2

31.2

Colo Sprgs 104 43.2 38 49.2

Fort Carson

Ft Col/Lovel

Ft Collins

Grand Jct

La Junta

104

105

108

46.2

1.2

4.8

31.8

103 31.2

40.8

34.8

7.2

Safford Awrs

Show Low

Williams AFB

109

110

111

40.8

40.2

49.2

16.2

Mount Shasta

Mount Wilson

North Is

Norton AFB

Ontario Intl

122

118

19.2

4.2

117

1.2

13.8

37.2

19.2

13.8

Winter Park

CONNECTICUT

105 52.2 40 0

Bridgeport 73 7.8 41 10.2

Danbury 73 28.8 41 22.2

Groton

Hartford

72 3

72 39

41 19.8

41 43.8

New 72 40.2 41 13.2

New 41 18

120 4.2 39 16.8

Tallahassee 84 22.2 30 22.8

Tampa

Honolulu Int

Kahului Maui

Kaneohe Mca

Kilauea Pt

LONGITUDE

degrees

81 19.2 28 25.8

80 3.6

82 3.6

81 15

82 33

82 31.8 27 58.2

80 4.8

157

156

158

159 min

55.8

25.8

16.8

40.2

LATITUDE degrees

80 7.2

87 1.2

28 13.8

27 58.2

28 46.8

27 24

28 31.2

22 min

Melbourne 80 37.8 28 6

Miami

Naples

Orlando

Patrick

80 16.8 25 49.2

81 4.8 26 7.8

Pensacola 87 19.2 30 21

Ruskin

Sanford

Sarasota

Titusville

Vero

West Palm

Beach

Whiting

GEORGIA

Albany

Alma

Athens

Atlanta

Augusta/Bush 81 58.2 33 22.2

Brunswick 81 22.8 31 9

Columbus 84 55.8 32 31.2

Hunter

Barbers Pt

Barking San

Fr Frigate

80 25.2 27 39

84 10.8 31 31.8

82 31.2 31 31.8

83 19.2 33 57

84 25.2 33 39

81 9

26 40.8

30 43.2

32 19.8

Ft 81 34.2 31 52.8

32 1.2

La 85 4.2 33 0.6

Macon/Lewis 83 39 32 42

Moody 83 1.2 30 58.2

Robins 32 37.8

Rome/Russell 85 10.2 34 21

Valdosta 83 16.8 30 46.8

Waycross

HAWAII

82 2.4 31 15

158

160

166

7.2

1.8

28.2

31.8

22.8

Glenview

NAS

Kankakee

LONGITUDE degrees min

LATITUDE degrees min

87 49.2 42 4.8

87 51 41 4.2

Macomb

Marion

90 39.6 40 31.2

89 0 37 45

Marseilles 88 40.8 41 22.2

Mattoon 88 16.8 39 28.8

Moline/Quad 90 31.2 41 27

Mount 88 51.6 38 19.2

Vernon

Peoria

Quincy

Rockford

Salem

89 40.8 40 40.2

91 1.2 39 55.8

89 0.6 42 12

88 57.6 38 37.8

89 51 38 33

Springfield 89 40.2 39 51

Sterling 89 40.2 41 44.4

Taylorville 89 19.8 39 31.8

Vandalia

INDIANA

89 10.2 38 59.4

Bakalar 86 3 39 22.8

Bloomington 86 37.2 39 7.8

Elkhart 86 0 41 43.2

Evansville 87 31.8 38 3

Fort 85 1.2 41 0

Gary 87 25.2 41 37.2

40 39

Indianapolis 86 16.2 39 43.8

Muncie 85 22.8 40 13.8

South 86 19.2 41 42

Terre 39 27

IOWA

Burlington 91 7.2 40 46.8

91 4.2 41 52.8

Des 93 39 41 31.8

Dubuque 90 4.2 42 24

Estherville 94 45 43 24

Fort 94 10.8 42 33

Lamoni 93 55.8 40 37.2

Mason 93 19.8 43 9

Ottumwa 92 27 41 6

Sioux 96 22.8 42 24

Spencer

KANSAS

95 9 43 10.2

92 2.4 42 33

Chanute

Col. J Jabar

95 28.8 37 40.2

97 13.2 37 45

Concordia 97 39 39 33

Dodge 99 58.2 37 46.2

LONGITUDE

degrees

LATITUDE min degrees min

Grand 90 4.2 29 10.8

High 94 2.4 28 7.8

Houma 90 39 29 34.2

Intercoastal 92 7.2 29 43.8

Lafayette 92 0 30 12

Lk 29 42

Monroe 92 3

28 46.8

32 31.2

Morgan 29 42

New 91 52.8 30 1.8

New 29 58.8

S Marsh Isl 91 58.8 28 18

Shreveport 93 45 32 31.2

Slidel 89 49.2 30 21

MAINE

Augusta

Bangor

69 4.8 44 19.2

68 49.2 44 48

Bar 68 22.2 44 27

Brunswick 69 55.8 43 52.8

Caribou 46 52.2

Greenville

Houlton

69 33 45 27

67 46.8 46 7.8

Loring 67 52.8 46 57

Portland 70 19.2 43 39

46 40.8

Rockland

Rumford

MARYLAND

69 7.2 44 4.2

70 52.8 44 52.8

Baltimore 76 40.2 39 10.8

Fort 76 46.2 39 4.8

Hagerstown 77 43.2 39 42

Ocean 75 7.8 38 33

Patuxent 76 2.4 38 16.8

Phillips

Salisbury

MASSACHUSETTS

76 10.2 39 28.2

75 3 38 19.8

Bedford

Beverly

71 16.8 42 28.2

70 55.2 42 34.8

Boston

Cape Cod

Chatham

71 1.8 42 22.2

70 3 41 46.8

69 58.2 41 40.2

Fort 42 34.2

Hyannis

Lawrence

70 16.8 41 40.2

71 7.2 42 43.2

Nantucket 70 4.2 41 15

Emporia 96 1.2 38 19.8

Norwood 71 10.8 42 10.8

Otis 70 31.2 41 39

Pittsfield 73 10.8 42 15.6

Upolo Pt Ln

Waimea-

Koha

IDAHO

Coeur d'Alene

Elk City

Idaho Falls

Malad City

156 28.2

156 7.2

20 25.2

20 0

116 49.2 47 46.2

115

112

25.8

4.2

19.2

49.2

31.2

10.2

Soda Springs

Sun Valley

Twin Falls

ILLINOIS

Alton

Aurora

111

114

34.8

1.8

28.8

90 3 38 52.8

88 19.2 41 46.2

38 34.2

Bloomington 88 55.8 40 28.8

Bradford 89 3.6 41 9.6

Cairo 89 13.2 37 4.2

Carbondale 89 15 37 46.8

Centralia 89 5.4 38 30.6

Champaign 88 16.8 40 1.8

Chicago 87 39 41 54

Danville

DeKalb

Decatur

87 3.6 40 12

88 43.2 41 55.8

88 52.2 39 49.8

88 15 41 55.2

Galesburg 90 25.8 40 55.8

Garden City

96 46.2 39 3

100 43.2 37 55.8

Hays 99 16.2 38 51

99 49.8 39 22.8

Hutchinson 97 52.2 38 4.2

94 52.8 38 49.2

Westfield

Westover

72 43.2 42 10.2

72 31.8 42 12

Worcester 71 52.2 42 16.2

MICHIGAN

Alpena 83 34.2 45 4.2

83 45 42 13.2

Manhatten

Olathe

Russell

Salina

Topeka

Topeka/Forbe

Wichita

KENTUCKY

96 40.2 39 9

98 34.8 37 18

94 5.4 38 51

98 49.2 38 52.2

97 39 38 48

95 37.2 39 4.2

95 40.2 38 57

97 25.8 37 39

86 25.8 36 58.2

Jackson

Lexington

London

Louisville

36 40.2

85 58.2 37 54

83 19.2 37 36

85 0 38 3

84 4.2 37 4.8

85 40.2 38 13.8

Owensboro 87 10.2 37 45

Paducah 88 46.2 37 4.2

Pikeville 82 31.2 37 28.8

LOUISIANA

Alexandria 92 1.8 31 22.8

Barksdale 93 40.2 32 30

Boothville

30 31.8

89 40.2 29 33

93 1.8 29 46.8

Claiborne 92 57 31 13.2

England 31 19.8

Eugene 91 46.8 28 28.2

93 1.2 31 3

Benton 86 25.8 42 7.8

Harbor

Chippewa 84 28.2 46 15

Coopersville 85 57 43 4.2

Copper 47 28.2

Detroit 83 1.2 42 25.2

Escanaba 87 4.8 45 43.8

Flint/Bishop 83 45 42 58.2

Hancock

Houghton

Lake

88 3 47 10.2

84 40.8 44 22.2

Ironwood

88 7.2 45 49.2

90 7.8 46 31.8

Jackson 84 28.2 42 16.2

Kalamazoo 85 33 42 13.8

Lansing 84 3.6 42 46.2

Manistee

Marquette

86 15

87 57

44 16.2

46 52.8

Menominee 87 37.8 45 7.2

Muskegon 86 15 43 10.2

Pellston 84 4.8 45 34.2

Pontiac 83 25.2 42 40.2

Saginaw 84 4.8 43 31.8

Sault 84 22.2 46 28.2

Sawyer 46 21

Selfridge 82 49.8 42 37.2

Seul 85 55.2 45 55.2

LONGITUDE

degrees

LATITUDE min degrees min

Wurtsmith 83 2.4 44 27

Ypsilanti 83 31.8 42 13.8

MINNESOTA

Albert 93 22.2 43 40.8

Alexandria 95 22.8 45 52.2

LONGITUDE degrees

NEBRASKA

Ainsworth min

LATITUDE degrees min

99 58.8 42 34.8

Santa Fe

Silver City

Brainerd-Crw 94 7.8

Duluth

Ely

Fairmont

Fergus 46 18

Hibbing

Litchfield

Mankato

Minneapolis 93 28.2 44 49.8

Park

Rochester

Saint

Thief

Tofte

Warroad

MISSISSIPPI

Columbus

AFB

92 3

93 3

94 4.2

88 27

43 55.2

44 55.8

45 33

96 10.8 48 4.2

90 49.8 47 34.8

95 21 48 55.8

Worthington 95 34.8 43 39

33 39

Greenville 90 58.8 33 28.8

Greenwood 90 4.8 33 30

Gulfport

Hattiesburg

Jackson

Laurel

Mccomb

92 51

89 4.2

89 19.8 31 28.2

90 4.8

46 24

92 10.8 46 49.8

91 49.2 47 54

94 25.2 43 39

47 22.8

93 22.8 48 34.2

94 31.2 45 7.8

93 55.2 44 13.2

46 54

30 24

32 19.2

89 10.2 31 40.2

90 28.2 31 10.8

LONGITUDE

degrees

106

108 min degrees

4.8

10.2

LATITUDE

32 min

37.2

37.8

Beatrice 96 45 40 19.2

Broken 41 25.8

Burwell 99 9 41 46.8

Truth Or Con 107 16.2 33 13.8

Columbus

Hastings

Kearney

Lincoln

97 21

95 34.8 40 4.2

98 25.8 40 36

99 0

41 27

40 43.8

40 51

Norfolk 97 25.8 41 58.8

96 1.2 41 22.2

100 40.8 41 7.8 North Platte

O'neill 98 40.8 42 28.2

Offutt 95 55.2 41 7.2

Omaha 95 5.4 41 18

Ord/Sharp 98 57 41 37.2

Sidney Muni

NEVADA

Battle Mtn

Fallon NAS

102

116

118

58.8

52.2

4.2

37.2

25.2

White Sands

NEW YORK

Albany

106 2.4 32 37.8

73 4.8 42 45

Ambrose 74 22.2 40 45

Binghamton 75 58.8 42 13.2

Buffalo 78 43.8 42 55.8

Dansville

Elmira

78 1.2

76 5.4

42 58.2

42 10.2

Farmingdale 73 25.8 40 43.8

75 43.8 44 3

Glens 73 37.2 43 21

Griffiss 43 13.8

Islip

Ithaca

73 0.6 40 46.8

76 28.2 42 28.8

Jamestown 79 15 42 9

Massena 74 51 44 55.8

Monticello 74 4.8 41 42

73 58.8 40 46.2

Newburgh 74 0.6 41 30

Niagara 43 6

Ogdensburg 75 2.4 44 40.8

Oneonta 75 7.2 42 52.2

Plattsburgh 73 28.2 44 39

Rochester 77 40.2 43 7.2

Saranac 74 1.2 44 22.8

Schenectady 73 55.8 42 51

Syracuse

Utica

76 7.2 43 7.2

75 22.8 43 9

Watertown 76 1.2 44 0

Westhampton 72 37.8 40 51

Ind Sprng Rn

Las Vegas

115

34.2

10.2

31.8

4.8

Nellis AFB 115 1.8 36 13.8

NORTH CAROLINA

Asheville 82 33 35 25.8

Cape 35 16.2

Charlotte 80 55.8 35 13.2

Meridian/Key 88 45 32 19.8

Natchez 91 15 31 37.2

Oxford

Tupelo

MISSOURI

89 32.4 34 23.4

88 46.2 34 16.2

Columbia

Cape

Girardeau

92 13.2 38 49.2

89 34.8 37 13.8

Ft 92 7.8 37 45

Joplin

Kirksville

Monett

Muskogee

Poplar

Whiteman

AFB

MONTANA

Cut Bank

94 3

92 33

94 21

112 22.2

37 10.2

40 6

37 19.8

95 21.6 35 39.6

90 28.2 36 46.2

Richards-Geb 94 33 38 51

Spickard 93 43.2 40 15

Springfield 93 22.8 37 13.8

St 95 31.8 40 16.8

90 22.2 38 45

Vichy/Rolla 91 46.2 38 7.8

West 92 25.2 37 13.2

93 33 38 43.8

48 36

Winnemucca 117 4.8 40 54

Yucca Flat

NEW HAMPSHIRE

Berlin

116 4.8 37 34.8

71 10.8 44 34.8

Concord

Jaffrey

Keene

71 3

72 0

43 12

42 48

72 16.2 42 54

Laconia

Lebanon

71 25.8 43 34.2

72 1.8 43 37.8

Manchester 71 25.8 42 55.8

Nashua

71 1.8 44 16.2

71 31.2 42 46.8

Pease 70 49.2 43 4.8

Wolfeboro 71 22.8 44 0

NEW JERSEY

Dare Co Gr 76 3 36 7.8

Elizabeth

35 15

76 10.8 36 16.2

Fayetteville 78 52.8 35 0

Fort

Hickory

Hot

Kinston

Mackall

78 55.8 35 7.8

Greensboro 79 57 36 4.8

81 22.8 35 45

82 49.2 35 54

Jacksonville 77 37.2 34 49.2

77 37.8 35 19.2

79 3

77 3

35 1.8

35 4.8

New 77 25.8 34 42

79 1.2 35 10.2

Raleigh-Durh 78 46.8 35 52.2

77 52.8 35 51

Fairfield

Lakehurst

74 16.8 40 52.2

74 21 40 1.8

Mcguire 40 1.2

Millville 75 4.2 39 22.2

Morristown 74 25.2 40 48

Newark 74 10.2 40 42

Teterboro 74 3 40 51

Trenton

NEW MEXICO

74 49.2 40 16.8

Wilmington 77 55.2 34 16.2

Winston-

Salem

NORTH DAKOTA

80 13.8 36 7.8

Devil's 48 7.2

Fargo 96 4.8 46 54

Jamestown 98 40.8 46 55.2

Lidgerwood 97 9 46 6

Minot 101 16.8 48 16.2

Drummond 113 46

Great Falls

Miles City

W Yellowston

111

105

111

22.2

52.2

0.6

28.8

25.8

Clayton Arpt

Holloman

AFB

Las Cruces

Las Vegas

Los Alamos

Northrup Str

103 9

106 0.6

106

105

106

46.2

16.8

2.4

36 27

32 51

52.8

OHIO

Athens

Canton

Cincinnati

82 13.8 39 12.6

81 25.8 40 55.2

84 40.2 39 3

Cleveland

Columbus

Dayton

81 40.8 41 31.2

82 52.8 40 0

84 1.2 39 54

Findlay

Mansfield

83 40.2 41 1.2

82 31.2 40 49.2

Rickenbacker 82 55.8 39 49.2

Toledo 83 4.8 41 36

Willoughby 81 2.4 41 37.8

Youngstown 80 40.2 41 16.2

Zanesville 81 5.4 39 57

LONGITUDE

degrees

LATITUDE min degrees min

OKLAHOMA

Ardmore

99 16.2 34 40.2

97 1.2 34 18

Bartlesville 96 0

Clinton 99 1.2

36 45

35 21

Enid 97 4.8 36 22.8

Gage

Hobart

Lawton

Mcalester

Norman

98 2.4 34 39

99 46.2 36 18

99 3 35 0

98 25.2 34 34.2

95 46.8 34 52.8

97 28.2 35 13.8

Oklahoma 97 3.6 35 24

Page 94 37.2 34 40.8

Ponca 97 0.6 36 43.8

Stillwater 97 5.4 36 9.6

Tinker 97 22.8 35 25.2

Tulsa 95 5.4 36 12

Vance 97 55.2 36 19.8

OREGON

LONGITUDE degrees min

LATITUDE degrees min

San Angelo

LONGITUDE

degrees

100

LATITUDE min degrees min

3 31 22.2

Shaw 80 28.2 33 58.2

Spartanburg 81 57.6 34 55.2

SOUTH DAKOTA

Aberdeen 98 25.8 45 27

Brookings 96 4.8 44 18

Chamberlain 99 19.2 43 48

Ellsworth

Huron

103 0.6 44 9

98 13.2 44 22.8

Stephenville 98 10.8 32 13.2

Temple 97 25.2 31 9

Tyler/Pounds 95 2.4 32 22.2

Victoria 96 55.2 28 51

Wichita 98 3 33 58.8

UTAH

Mitchell 98 1.8 43 46.2

Bullfrog Mar

Cedar City

110

113

4.2

0.6

Burns Arpt

Cape Blanco

Klamath Fall

La Grande

Lake View

North Bend

The Dalles

PENNSYLVANIA

Allentown

Altoona

Blairsville

Bradford

Dubois

Erie

Franklin

Lancaster

Latrobe

Muir

Nth

118

124

121

118

120

124

121

43.8

75 25.8 40 39

78 19.2 40 18

79 5.4

76 1.8

22.8

16.8

10.8

25.2

37.2

40 16.2

78 37.8 41 48

78 5.4 41 10.8

80 10.8 42 4.8

79 52.2 41 22.8

Harrisburg 76 51 40 13.2

Johnstown 78 49.8 40 19.2

40 7.8

79 2.4 40 16.8

Middletown 76 46.2 40 12

76 34.2 40 25.8

40 4.8

Philadelphia 75 15 39 52.8

Philipsburg 78 7.8 41 28.2

Pittsburgh 79 55.8 40 21

Reading 75 58.2 40 22.8

77 25.8 39 43.8

Wilkes-Barre 75 43.8 41 19.8

Williamsport 76 55.2 41 15

40 12

RHODE ISLAND

Rapid City 103 4.2 44 3 Eagle Range

Green River

113

110

4.2

Sioux 96 43.8 43 34.8

Watertown 97 9

Yankton

44 55.2

97 22.8 42 55.2

TENNESSEE

Bristol 82 2.4 36 28.8

Chattanooga 85 1.2 35 1.8

Clarksville 87 25.2 36 37.2

Crossville 85 4.8 35 57

Dyersburg 89 2.4 36 1.2

Jackson

Knoxville

88 55.2 35 36

83 58.8 35 49.2

35 3

Monteagle 85 30.6 35 9

Nashville 86 40.8 36 7.2

Smyrna 86 3 36 0

TEXAS

Abilene

Alice 98 1.8

99 40.8 32 25.2

27 43.8

Hill AFB

Saint George

Salt Lake Ct

111

113

111

58.2

Price/Carbon 110 45

3.6

58.2

39 37.2

7.2

4.8

46.8

Austin

Big Sky

Big Spring

Chase

97 4.2

101

28.8

30 18

23.4

Brownsville 97 25.8 25 54

Brownwood 98 57.6 31 47.4

97 25.8 32 46.8

97 40.2 28 22.2

VERMONT

Burlington 73 9 44 28.2

Montpelier 72 34.2 44 12

Newport 72 19.8 45 33

Rutland 73 57 43 31.8

St 44 25.2

Wilmington 72 52.8 42 52.8

VIRGINIA

Charlottes 78 27 38 7.8

Chesapeake 76 1.2 37 30

Danville 79 19.8 36 34.2

Fort 77 10.8 38 43.2

Fort 76 37.2 37 7.8

Hot 79 49.2 37 57

College 96 22.2 30 34.8

Cotulla

27 46.2

99 13.2 28 27

Lynchburg 79 1.2 37 19.8

Newport 76 3 37 7.8

News

Dallas/FW 97 1.8 32 54

Del Rio 100 55.2 29 22.2

Dyess 99 51 32 25.8

El Paso 106 2.4 31 48

Ellington 95 10.2 29 37.2

Fort 97 21 32 49.2

Ft Hood Aaf

Galveston

Greenville

Guadalupe

Harlingen

Hondo

Houston

Junction

97 43.2 31 9

94 52.2 29 16.2

97 49.8 31 4.2

96 4.2

104 4.8

33 4.2

31 49.8

97 40.2 26 13.8

99 10.2 29 21

95 21 29 58.2

99 46.2 30 30

98 34.8 29 22.8

99 4.8 29 58.8 Kerrville

Killeen

Kingsville

97 40.8 31 4.8

97 49.2 27 30

Laredo 99 28.2 27 31.8

Laughlin AFB

Longview

100 46.8 29 22.2

94 43.2 32 22.8

Lufkin 94 45 31 13.8

Norfolk 36 54

Oceana 36 49.2

Quantico 38 30

Richmond

Roanoke

77 19.8 37 30

79 58.2 37 19.2

Muni

Staunton

Volens

78 51 38 16.2

78 58.8 36 57

WASHINGTON

Fort Lewis

Mcchord AFB

Moses Lake

Oak Harbor

122

119

122

34.8

28.8

19.2

40.8

4.8

Providence 71 25.8 41 43.8

SOUTH CAROLINA

Anderson 82 43.2 34 30

Beaufort 80 43.2 32 28.8

Charleston 80 1.8 32 54

Columbia 81 7.2 33 57

Florence 79 43.2 34 10.8

Greenville 82 21 34 51

Mcentire 80 4.8 33 55.2

Mcallen

Mineral

Palacios

Paris/Cox

98 13.8 26 10.8

96 15

95 27

32 46.8

28 43.2

33 37.8

Port 94 1.2 30 34.8

Reese AFB

Rockport

102

97 1.8

3 33

28 4.8

Port Angeles 123 3

Quillayute 124 33

48 7.2

Walla Walla

Wenatchee

Whidbey Is

LONGITUDE

degrees

118

LATITUDE min degrees min

16.8 46 6

122 39 48 21

WEST VIRGINIA

LONGITUDE degrees

WISCONSIN

LATITUDE min degrees min

Eau Claire 91

28.8

7.8

52.2

28.8

10.8

52.2

LONGITUDE

degrees

WYOMING

110

LATITUDE min degrees min

0.6

Evanston 111 0

57 43.8

42 34.2

Wh Sulphur 80 1.2 37 27.6

C A N A D A

CITY PROVINCE LONGITUDE

Calgary Alberta 114

Rhinelander 89 27

Rice Lake 91

43.2

16.2

LATITUDE

Coppermine Northwest 49

Edmonton Alberta 113 25 53 34

Frederickton

Ft Mcpherson

Goose Bay

New Brunswick 66

Northwest Terr 134

Newfoundland 60

Halifax Nova Scotia 63

Hazelton BC

Kenora Ontario 94

66 Labrador City Labrador

Montreal Quebec

Mt. Logan Yukon 140

24 60 34

Nakina Yukon

Ottawa

Peace River

Ontario

Alberta

117

45 18

56 15

Pr. Edward Isl Nova Scotia 63 9 46 14

Quebec Quebec 71

Regina Saskatchewan 104 38 50 30

St. Johns Newfoundland 52 43 47 34

Toronto Ontario 79

Vancouver BC

Victoria BC

123

123 20 48

Whitehorse Yukon 135 3 60

Winnipeg Manitoba 97 53

I I N T E R N A T I I O N A L

Aberdeen Scotland

Adelaide

Amsterdam

Ankara

Asunción

Athens

Auckland

Bangkok

Barcelona

Belém

Belfast

Belgrade

Berlin

Birmingham

Bombay

Australia

Holland

Turkey

Paraguay

Greece

New Zealand

Thailand

Spain

Brazil

Northern Ireland

Yugoslavia

Germany

England

India

Bordeaux

Bremen

Brisbane

Bristol

Brussels

Bucharest

France

Germany

Australia

England

Belgium

Romania

Budapest Hungary

Buenos Aires Argentina

Cairo Egypt

Canton

Cape Town

Caracas

Chihuahua

Chongqing

China

South Africa

Venezuela

Mexico

China

Copenhagen Denmark

Córdoba Argentina

Darwin Australia

Dublin

Durban

Edinburgh

Frankfurt

Georgetown

Ireland

South Africa

Scotland

Germany

Guyana

9 w

31 w

49 e

8 e

35 w

22 e

7 e

5 e

22 w

21 e

15 e

22 e

2 w

5 w

34 e

10 w

51 e

15 w

53 e

10 w

41 e

15 w

36 e

53 e

55 e

40 w

43 e

45 e

30 e

9 e

29 w

56 w

32 e

25 e

55 w

48 e

153

113

106

130

138

174

100

57 9 n

34 55 s

52 22 n

39 55 n

25 15 s

37 58 n

36 52 s

13 45 n

41 23 n

1 28 s

54 37 n

44 52 n

52 30 n

52 25 n

19 0 n

44 50 n

53 5 n

27 29 s

51 28 n

50 52 n

44 25 n

47 30 n

34 35 s

30 2 n

23 7 n

33 55 s

10 28 n

28 37 n

29 46 n

55 40 n

31 28 s

12 28 s

53 20 n

29 53 s

55 55 n

50 7 n

6 45 n

28.8

55.8

Rock Springs

CITY

Glasgow

COUNTRY

Scotland

Guatemala City Guatemala

Guayaquil

Hamburg

Ecuador

Germany

Hammerfest

Havana

Helsinki

Hobart

Iquique

Irkutsk

Norway

Cuba

Finland

Tasmania

Chile

Russia

Jakarta Indonesia

Johannesburg South Africa

Kingston Jamaica

La Paz

Leeds

Lima

Bolivia

England

Peru

Liverpool

London

Lyons

Madrid

Manchester

Manila

Marseilles

Mazatlán

England

France

Spain

England

Phillipines

France

Mexico

Mecca

Melbourne

Mexico City

Milan

Montevideo

Moscow

Munich

Nagasaki

Nagoya

Nairobi

Nanjing

Naples

Saudi Arabia

Australia

Mexico

Italy

Uruguay

Russia

Germany

Japan

Kenya

China

Italy

Newcastle

Odessa

Osaka

Oslo

Panama City

Paramaribo

Paris

Beijing

England

Ukraine

Japan

Norway

Panama

Surinam

France

China

Perth

Plymouth

Australia

England

Rio de Janeiro Brazil

Rome

Salvador

Santiago

Italy

Brazil

Chile

St. Petersburg Russia

Sao Paulo Brazil

Shanghai China

Sofia

Stockholm

Sydney

Bulgaria

Sweden

Australia

Tananarive

Teheran

Tokyo

Tripoli

Venice

Veracruz

Vienna

Warsaw

Wellington

Zürich

Madagascar

Iran

Japan

Libya

Italy

Mexico

Austria

Poland

New Zealand

Switzerland

109

Yellowstone 110 25.2

135

116

115

144

129

136

118

121

151

139

174

106

120

106

LONGITUDE

4 15 w

90 31 w

56 w

2 e

147

104

38 e

23 w

0 e

19 e

7 w

20 e

48 e

4 e

49 w

22 w

30 w

2 w

0 w

5 w

50 e

42 w

15 w

57 e

20 e

25 w

18 e

31 w

28 e

20 e

3 e

0 e

33 e

45 e

12 e

20 e

10 w

20 e

0 e

47 e

31 e

37 w

48 e

30 e

42 e

32 w

15 w

20 e

25 e

52 e

5 w

12 w

27 e

27 w

45 w

45 e

58 e

7 w

10 e

10 w

36 e

35 e

57 e

56 e

55 e

53 e

15 e

4.2

LATITUDE

55 50 n

14 37 n

10 s

33 n

38 n

8 n

10 n

52 s

10 s

30 n

16 s

12 s

59 n

27 s

45 n

0 s

25 n

32 n

45 n

26 n

30 n

35 n

20 n

12 n

56 n

31 s

10 n

40 n

17 n

0 s

50 s

45 n

40 n

57 n

26 n

10 n

14 n

17 s

21 n

58 n

27 n

32 n

57 n

58 n

45 n

48 n

55 n

57 s

25 n

57 s

54 n

56 s

28 s

29 n

47 s

26 n

27 n

53 s

45 n

8 n

48 n

7 n

25 s

3 n

50 n

41 36

Appendix D - RS-232 Connection

You can control your telescope with a computer via the RS-232 port on the computerized hand control and using an optional RS-232 cable (#93920). Once connected, the telescope can be controlled using popular astronomy software programs.

Communication Protocol:

The Advanced GT communicates at 9600 bits/sec, No parity and a stop bit. All angles are communicated with 16 bit angle and communicated using ASCII hexadecimal.

Description PC Command ASCII Hand Control Response

Notes

Echo

Goto Azm-Alt

B12AB, 4000

Goto Ra-Dec

Get Azm-Alt

Get RA-Dec

Cancel Goto

Is Goto in Progress

R34AB, 12CE

12AB, 4000#

34AB, 12CE#

0# or 1#

Useful to check communication

10 characters sent. B=Command,

12AB=Azm, comma, 4000=Alt. If command conflicts with slew limits, there will be no action.

Scope must be aligned. If command conflicts with slew limits, there will be no action.

10 characters returned,

12AB=Azm, comma, 4000=Alt, #

Scope must be aligned

0=No, 1=Yes; "0" is ASCII character zero

0=No, 1=Yes Is Alignment Complete

Commands below available on version 1.6 or later

HC version

Stop/Start Tracking

32-bit goto RA-Dec

32-bit get RA-Dec

Tx x = 0 (Tracking off) x = 1 (Alt-Az on) x = 2 (EQ-N) x = 3 (EQ-S)

2 2

Two bytes representing V2.2

Alt-Az tracking requires alignment r34AB0500,12CE0500 # e 34AB0500,12CE0500# The last two characters will always be zero.

Commands below available on version 2.2 or later

32-bit goto Azm-Alt

32-bit get Azm-Alt b34AB0500,12CE0500 # z 34AB0500,12CE0500# The last two characters will always be zero.

The cable required to interface to the telescope has an RS-232 male plug at one end and a 4-4 telephone jack at the other end. The wiring is as follows:

Additional RS232 Commands

S e n d A n y T r a c k R a

t

t e T h r o u g h R S 2 3 2 T o T h e

H

a n d C o n t

t r

r o l

l

1. Multiply the desired tracking rate (arcseconds/second) by 4. Example: if the desired trackrate is 150 arcseconds/second, then TRACKRATE = 600

2. Separate TRACKRATE into two bytes, such that (TRACKRATE = TrackRateHigh*256 + rackRateLow). Example: TrackRateHigh = 2 TrackRateLow = 88

3. To send a tracking rate, send the following 8 bytes: a. Positive Azm tracking: 80, 3, 16, 6, TrackRateHigh, TrackRateLow, 0, 0 b. Negative Azm tracking:80, 3, 16, 7, TrackRateHigh, TrackRateLow, 0, 0 c. Positive Alt tracking: 80, 3, 17, 6, TrackRateHigh, TrackRateLow, 0, 0 d. Negative Alt tracking: 80, 3, 17, 7, TrackRateHigh, TrackRateLow, 0, 0

4. The number 35 is returned from the handcontrol

Send A Slow-Goto Command Through RS232 To The Hand Control

(note: Only valid for motorcontrol version 4.1 or greater)

1. Convert the angle position to a 24bit number. Example: if the desired position is 220

°, then

POSITION_24BIT = (220/360)*2

= 10,252,743

2. Separate POSITION_24BIT into three bytes such that (POSITION_24BIT = PosHigh*65536 +

PosMed*256 + PosLow). Exampe: PosHigh = 156, PosMed = 113, PosLow = 199

3. Send the following 8 bytes: a. Azm Slow Goto: 80, 4, 16, 23, PosHigh, PosMed, PosLow, 0 b. Alt Slow Goto: 80, 4, 17, 23, PosHigh, PosMed, PosLow, 0

4. The number 35 is returned from the handcontrol

Reset The Position Of Azm Or Alt

1. Convert the angle position to a 24bit number, same as Slow-Goto example.

2. Send the following 8 bytes: a. Azm Set Position: 80, 4, 16, 4, PosHigh, PosMed, PosLow, 0 b. Alt Set Position: 80, 4, 17, 4, PosHigh, PosMed, PosLow, 0

3. The number 35 is returned from the handcontrol

4. Note: If using Motorcontrol version less than 4.1, then send: a. Azm Set Position: 80, 3, 16, 4, PosHigh, PosMed, PosLow, 0 b. Alt Set Position: 80, 3, 17, 4, PosHigh, PosMed, PosLow, 0

APPENDIX E – MAPS OF TIME ZONES

CELESTRON TWO YEAR WARRANTY

A. Celestron warrants this telescope to be free from defects in materials and workmanship for two years. Celestron will repair or replace such product or part thereof which, upon inspection by Celestron, is found to be defective in materials or workmanship.

As a condition to the obligation of Celestron to repair or replace such product, the product must be returned to Celestron together with proof-of-purchase satisfactory to Celestron.

B. The Proper Return Authorization Number must be obtained from Celestron in advance of return. Call Celestron at (310) 328-

9560 to receive the number to be displayed on the outside of your shipping container.

All returns must be accompanied by a written statement setting forth the name, address, and daytime telephone number of the owner, together with a brief description of any claimed defects. Parts or product for which replacement is made shall become the property of Celestron.

The customer shall be responsible for all costs of transportation and insurance, both to and from the factory of

Celestron, and shall be required to prepay such costs.

Celestron shall use reasonable efforts to repair or replace any telescope covered by this warranty within thirty days of receipt. In the event repair or replacement shall require more than thirty days, Celestron shall notify the customer accordingly. Celestron reserves the right to replace any product which has been discontinued from its product line with a new product of comparable value and function.

This warranty shall be void and of no force of effect in the event a covered product has been modified in design or function, or subjected to abuse, misuse, mishandling or unauthorized repair. Further, product malfunction or deterioration due to normal wear is not covered by this warranty.

CELESTRON DISCLAIMS ANY WARRANTIES, EXPRESS OR IMPLIED, WHETHER OF MERCHANTABILITY OF

FITNESS FOR A PARTICULAR USE, EXCEPT AS EXPRESSLY SET FORTH HEREIN.

THE SOLE OBLIGATION OF CELESTRON UNDER THIS LIMITED WARRANTY SHALL BE TO REPAIR OR

REPLACE THE COVERED PRODUCT, IN ACCORDANCE WITH THE TERMS SET FORTH HEREIN. CELESTRON

EXPRESSLY DISCLAIMS ANY LOST PROFITS, GENERAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES

WHICH MAY RESULT FROM BREACH OF ANY WARRANTY, OR ARISING OUT OF THE USE OR INABILITY TO

USE ANY CELESTRON PRODUCT. ANY WARRANTIES WHICH ARE IMPLIED AND WHICH CANNOT BE

DISCLAIMED SHALL BE LIMITED IN DURATION TO A TERM OF TWO YEARS FROM THE DATE OF ORIGINAL

RETAIL PURCHASE.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitation on how long an implied warranty lasts, so the above limitations and exclusions may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Celestron reserves the right to modify or discontinue, without prior notice to you, any model or style telescope.

If warranty problems arise, or if you need assistance in using your telescope contact:

Celestron

2835 Columbia Street

Torrance, CA 90503 U.S.A.

Fax. (310) 212-5835

Monday-Friday 8AM-4PM PST

This warranty supersedes all other product warranties.

NOTE: This warranty is valid to U.S.A. and Canadian customers who have purchased this product from an Authorized

Celestron Dealer in the U.S.A. or Canada. Warranty outside the U.S.A. and Canada is valid only to customers who purchased from a Celestron Distributor or Authorized Celestron Dealer in the specific country and please contact them for any warranty service.

Celestron

2835 Columbia Street

Torrance, CA 90503 U.S.A.

Tel. (310) 328-9560

Fax. (310) 212-5835

Web site at http//www.celestron.com

(Products or instructions may change without notice or obligation.)

Item # 21021-INST

Printed in China

$10.00

07-05