World Marketing of America GFN2819R-GFP2820R Gas Fireplace Owner Manual

Kozy-World
V E N T-F R E E G A S
FIREPLACE SYSTEM
R
O W N E R ’S O P E R AT I O N A N D I N S TA L L AT I O N
MANUAL
WARNING : I f the in fo rmatio n i n
this manual is not followed exactly, a
fi r e o r ex p l o si o n may resu l t causing
property damage, personal injury, or loss
of life.
GFN2815R
GFP2816R
GFN2817R
GFP2818R
GFN2819R
GFP2820R
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
WHAT TO DO IF YOU SMELL GAS
WAR N I N G : Im p ro p e r i n s t a l l a tio n ,
adjustment, alteration, service or maintenance
can cause injury or property damage. Refer to
this manua l for correct ins tallation an d
operational procedures. For assistance or add i ti o n al in form a ti o n co n s u lt a q u a l i fi e d
installer, service agency, or gas supplier.
WARNING:
This is an unvented gasfired heater. It uses air (oxygen)f r o m t h e
r o o m i n w h i c h i t i s installed. Provisions
for adequate combustion and ventilation air
must b e p ro v i d e d . R e fe r to A i r F o r Combustion and Ventilation section on page 5 of
this manual.
l Do not try to light any appliance.
l Do not touch any electrical switch; do not
use any phone in your building.
l Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
l If you cannot reach your gas supplier, call
the fire department.
Installation and service must be performed by a
qualified installer, service agency, or the gas
supplier.
T h is app liance may be in stalled i n an
aftermarket*, permanently located, manufactured
(mobile) home, where not prohibited by local
codes.
This appliance is only for use with the type of
gas indi cated on the ratin g pl ate. T his
appliance is not convertible for use with other
gases.
WATER VAPOR: ABY-PRODUCT OF NOVENTED ROOM
HEATERS
Water vapor is a by-product of gas combustion.An unvented
room heater produces approxinately one(1) ounce (30ml)
World Marketing of America, Inc. of water for every 1,000 BTU’s(.3KW’s) of gas input per
P. O. Box 192, Rt.. 22 West
hour. Refer to page 4.
Mill Creek, PA 17060
Consumer: Please retain these instructions for future
use.
KOZY WORLD PHONE NUMBER :(814)643-1775
http://www.worldmkting.com
Installer: Please leave these instructions with the
consumer.
*Aftermarket: Completion of sale, not for purpose of resale,
from the manufacturer.
1
Table of Contents
Safety Information Warnings....................................3
Air for Combustion and Ventilation...........................5
Installation...............................................................7
Operating heater.....................................................10
Cleaning&Maintenance...........................................13
Trouble Shooting....................................................15
Specifications.........................................................16
Replacement .........................................................17
Parts List................................................................19
Logs installation instruction.....................................21
Mantel installation instructions................................22
Assembling anchor.................................................27
2
SAFETY INFORMATION WARNINGS
WARNING: Do not allow
fans to blow directly into the heater.
Avoid any drafts that alter burner
flame patterns. Ceiling fans can create drafts that alter burner flame
patterns. Altered burner patterns
can cause sooting .
.
I M P O R TA N T:
Read
th is
owner’s manual carefully and
com pletely before tryi ng to
assemble, operate, or service
this heater. Improper use of
this heater can cause serious
injury or death from burns,
f i r e , e x p l o s i o n , e l e c t ri c a l
shock, and carbon monoxide
poisoning.
WARNING: Do not use a blower
insert, heat exchanger insert, or other
accessory not approved for use with
this heater.
DANGER: Carbon monoxide
poisoning may lead to death!
Carbon Monoxide Poisoning:
Early signs of carbon monoxide
poisoning resemble the flu with
headaches, dizziness, or nausea.
If you have these signs, the heater
may not be working properly. Get
fresh air immediately! Have heater
serviced. Some people are more
affected by carbon monoxide than
others. These include pregnant
women, people with heart, or lung
disease, anemia, those under the
influence of alcohol, and those
at high altitudes.
Propane/LP Gas: Propane/Lp gas
is odorless. An odor-making agent
is added to Propane/Lp gas. The
o d o r h elp s
yo u
detect
a
Propane/Lp gas leak. However,
the odor added to Propane/Lp gas
can fade. Propane/Lp gas may be
present even though no odor
exists.
M a k e c e r t a i n yo u r e a d a n d
understand all warnings. Keep this
manual for reference. It is your guide
to safe and p roper operat ion
of this heater.
Due to high temperatures, the
appliance should be located out of
traffic and away from furniture
and draperies.
Do not place clothing or other
flammable material on or near the
appliance. Never place any objects
in the fireplace.
Heater becomes very hot when
running fireplace. Keep children and
adults away from hot surfaces to
avoid burns or clothing ignition.
Fireplace will remain hot for a
time after shutdown. Allow surfaces
to cool before touching.
Carefully supervise young children
when they are in the room with
fireplace.
You must operate this heater with
the heater screen in place. Make
sure heater screen is in place
before running heater.
Keep the appliance area clear and
free from combustible materials,
gasoline, and other flammable
vapors and liquids.
WARNING:
Any change to
this fireplace or its controls can
be dangerous.
State of Massachusetts: The in-
1. This appliance is only for use
with the type of gas indicated
on the rating plate. This
appliance is not convertible for
use with other gases.
2. Do not place Propane/Lp
supply tank(s) inside any
structure. Locate Propane/Lp
supply tank(s) outdoors.
3. If you smell gas
l Shut off gas supply.
l Do not try to light any appliance.
l Do not touch any electrical switch:
stallation must be made by a licensed
plumber or gas fitter in the Commonwealth of Massachusetts.
Sellers of unvented propane or natural gas-fired supplemental room heaters shall provide to each purchaser a
copy of 527 CMR 30 upon sale of the
unit.
In t h e st at e o f M assac h u set t s,
unvented propane or nature gas-fired
space heaters shall be prohibited in
do not use any phone in your
building.
bedrooms and bathrooms.
3
l Immediately call your gas supplier
l
from a neighbor’s phone. Follow
the gas supplier’s instructions.
If you cannot reach your gas
supplier, call the fire department.
4. This heater shall not be installed
in a bedroom or bathroom.
5. Do not use this heater as a
wood-burning heater. Use only
the logs provided with the heater.
6. Do not add extra logs or ornaments
such as pine cones, vermiculite, or
rock wool.Using these added items
can cause sooting. Do not add lava
rock around base. Rock and debris
could fall into the control area of
heater. After servicing, always
replace screen before operating
heater.
7. You must operate this heater with
the heater screen in place. Make
sure heater screen is in place
before running heater.
8. This heater is designed to be
smokeless. If logs ever appear to
smoke, turn off heater and call a
qualified service person. Note:
During initial operation, slight
smoking could occur due to log
c u rin g an d h eater b u rn in g
manufacturing residues.
9. To prevent the creation of soot,
follow the instructions in Cleaning
and Maintenance(page 13).
10.Before using furniture polish, wax,
carpet cleaner, or similar products,
turn heater off. If heated, the
vapors from these products may
create a white powder residue
within burner box or on adjacent
walls or furniture.
11 . T h is h eat er n eed s f r esh air
ventilation to run properly. This
heater has an Oxygen Depletion
Sensing (ODS) safety shutoff
system. The ODS shuts down the
heater if not enough fresh air is
available. See Air for Combustion
and Ventilation, pages 5 through 6.
If heater keeps shutting off, see
Tro u b l e sh o o t i n g , p ag es 1 5
through 16.
12. Do not run heater:
l
l
Where flammable liquids or
vapors are used or stored.
Under dusty conditions.
13.Do not use this heater to cook
food or burn paper or other objects.
14. Do not use this heater if any part
has been under water. lmmedia-
SAFETY INFORMATION
Continued
15. Turn off and unplug heater and let
c ool bef ore servicing . O nly a
qualified service person should
service and repair heater.
16. Operating heater above elevations
of 4,500 feet could cause pilot
outage.
17. Do not operate heater if any log is
broken. Do not operate heater if any
log is ch ipped (dime-sized or
larger).
18. To prevent performance problems,
do not use propane/LP fuel tank of
less than 100 lbs. capacity.
LOCAL CODES
UNPACKING
ln stall and use h eater with care.
F o llo w all lo c a l c o d es. In th e
ab senc e of loc al co des, u se t he
latest edition of The National Fuel
Gas Code, ANSI Z223.1, also known
as NFPA 54*.
*Available from:
American National Standards
lnstitute, lnc.
1430 Broadway
New York, NY 10018
National Fire Protection
Association, lnc.
Batterymarch Park
Quincy. MA 02269
This heater is designed for vent-free
operation. State and local codes in
som e areas proh ibit t h e use o f
vent-free heaters.
1.
2.
3.
4.
5.
6.
Remove top inner pack.
Tilt carton so that stove is upright.
Remove protective side packaging.
Slide stove out of carton.
Remove protective plastic wrap.
Remove two self-tapping screws
on t he screw , t hen lift an d
pulling forward.
7. Remove log set by cutting plastic
ties.
8. Carefully unwrap log.
9. Check for any shipping damage. If
stove or log is damaged, promptly
inform dealer where you bought
stove.
PRODUCT IDENTIFICATION
PRODUCT FEATURES
SAFETY PILOT
This heater has a pilot with an
Oxygen Depletion Sensing (ODS)
safety shutoff system. The ODS/pilot
is a required feature for vent-free
room heaters. The ODS/pilot shuts off
the heater if there is not enough
fresh air.
Remote control SYSTEM
This fireplace has a remote transimitter.This system requires three
AAA, and requires electric power
outlet to operate.
Figure1- Vent Free LP/NG Gas Stove
WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS
Water vapor is a by-product of gas combustion. An unvented room heater produces approximately one(1) ounce
(30ml) of water for every 1,000 BTU’s(3KW’s)of gas input per hour.
Unvented room heaters are recommended as supplemental heater(a room). Rather than a primary heat source
(an entire house). In most supplemental heat applications, the water vapor does not creat a problem. In most
applications,the water vapor enhances the low humidity atmosphere experienced during cold weather.The folling
steps will help insure that water vapor does not become a problem.
1.Be sure the heater is a sized properly for the application, including ample combustion air and circulation air.
2.If high humidity is experienced,dehumidifier may be used to help lower the water vapor content of the air.
3.Do not use an unvented room heater as the primary heat source.
4
AIR FOR COMBUSTION AND VENTILATION
WARNING:
This heater shall
not be installed in a confined space
or unusually tight construction unless provisions are provided for adequate combustion and ventilation
air. Read the following instructions
to insure proper fresh air for this
andother fuel-burning appliances in
your home.
PROVIDING ADEQUATE
VENTILATION
The following are excerpts from
National Fuel Gas Code, NFPA 54/
AN SZ 22 3. 1,S ec ti on 5. 3, Ai r fo r
Combustion and Ventilation.
All spaces in homes fall into one of
th e t hree f ollo wing ven tilation
classifications:
1. Unusually Tight Construction
2. Unconfined Space
3. Confined Space
The information on pages 5 through 6
will help you classify your space and
provide adequate ventilation.
Confined and Unconfined Space
Unusually Tight Construction
The National Fuel Gas Code, ANSI
Z223.1 defines a confined space as a
space whose volume is less than 50
cubic feet per 1,000 Btu per hour
(4.8 m 3 per kw) of the aggregate
input rating of all appliances installed
in that space and an unconfining
space as a space whose volume is
not less than 50 cubic feet per 1,000
Btu per hour (4.8 m 3 per kw) of the
aggregate input rating of all appliances
installed in that space. Rooms
communicating directly with the space
in which the appliances are installed*,
through openings not furnished with
doors, are considered a part of the
unconfined space.
The air that leaks around doors and
windows may provide enough fresh
air for combustion and ventilation.
However, in buildings of unusually tight
c o n st ru c t io n , yo u m u s t p r o vi d e
additional fresh air.
Unusually tight construction is
defined as construction where:
a) walls and ceilings exposed to the
outside atmosphere have a
continuous water vapor retarder
with a rating of one perm (6×10-11kg
p er p a- s ec -m 2 ) o r l es s w it h
openings gasketed or sealed and
b) weather stripping has been added
on windows that can be opened
and doors and
c) caulking or sealants are applied
to areas such as joints around
window and door frames, between
sole plates and floors, between
wall-ceiling joints, between wall
p an els, at p en etratio n s fo r
plumbing, electrical, and gas
lines, and at other openings.
If your home meets all of the three
criteria above, you must provide
additional fresh air. See Ventilation Air
From Outdoors (page 6).
If your home does not meet all of the
t hree c riteria ab ove, p ro ceed t o
Determining Fresh-Air Flow For
Heater Location (below).
This heater shall not be installed in
a confined space or unusually tight
construction unless provisions are
provided for adequate combustion
and ventilation air.
* Adjoining rooms are communicating
only if there are doorless passageways or ventilation grills between
them.
DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION
Determining if You Have a Confined or Unconfined Space
Use this worksheet to determine if you have a confined or unconfined space.
Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways
or ventilation grills between the rooms.
1. Determine the volume of the space (length×width×height).
Length×Width×Height=
cu.ft. (volume of space)
Example: Space size 20ft. (length)×16ft.(width)×8ft. (ceiling height)=2560cu. ft. (volume of space)
If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these
rooms to the total volume of the space.
2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.
(volume of space)÷50 cu. ft.=(Maximum Btu/Hr the space can support)
Example: 2560 cu. ft. (volume of space)÷50 cu.ft.=51.2 or 51,200(maximum Btu/Hr the space can support)
5
3. Add the Btu/Hr of all fuel burning appliances in the space.
Vent-free heater
Btu/Hr
Example:
Gas water heater*
Btu/Hr
Gas
water heater
30,000
Btu/Hr
Gas furnace
Btu/Hr
Vent-free heater +
26,000
Btu/Hr
Vented gas heater
Btu/Hr
Total
= 56,000
Btu/Hr
Gas heater logs
Btu/Hr
Other gas appliances* +
Btu/Hr
Total
=
Btu/Hr
*Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and
vents to the outdoors.
4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.
Btu/Hr (maximum the space can support)
Btu/Hr (actual amount of Btu/Hr used)
Example : 51,200 Btu/Hr(maximum the space can support)
56,000 Btu/Hr(actual amount of Btu/Hr used)
The space in the above example is a confined space because the actual Btu/Hr used is more than the
maximum Btu/Hr the space can support.
You must provide additional fresh air. Your options are as follows:
A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined
space, remove door to adjoining room or add ventilation grills between rooms. See Ventilation Air From
Inside Building (below).
B. Vent room directly to the outdoors. See Ventilation Air From Outdoors (below).
C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.
If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an
unconfined space. You will need no additional fresh air ventilation.
WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined
space or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one
of the methods described in the National Fuel Gas Code, ANSI Z223.1, Section 5.3 or applicable local codes.
Ventilation Air From lnside Building
This fresh air would come from an adjoining unconfined
space. W hen ventilating to an adjoining unconfined
space, you must provide two permanent openings: one
within 12" of the ceiling and one within 12" of the floor
on the wall connecting the two spaces (see options 1
and 2, Figure 2). You can also remove door into
adjoining room (see option 3, Figure 2). Follow the
National Fuel Gas Code. NFPA 54/ANSI Z223.1, Section 5.3, Air for Combustion and Ventilation for required size of ventilation grills or ducts.
Ventilation Air From Outdoors
Provide extra fresh air by using ventilation grills or ducts.
You must provide two permanent openings: one within
12" of the ceiling and one within 12" of the floor. Connect
these items directly to the outdoors or spaces open to the
outdoors. These spaces include attics and crawl spaces.
Follow the National Fuel Gas Code, NFPA 54/ANSI
Z223.1, Section 5.3, Air for Combustion and Ventilation
for required size of ventilation grills or ducts.
IMPORTANT: Do not provide openings for inlet or outlet
air into attic if attic has a thermostat-controlled power vent.
Heated air entering the attic will activate the power vent.
WARNING: Rework worksheet, adding
the space of the adjoining unconfined
space. The combined spaces must have
enough fresh air to supply all appliances in
both spaces.
6
Figure 2 -Ventilation Air from Inside Building
Figure 3 -Ventilation Air from Outdoors
INSTALLATION
NOTICE: This heater is
intended for use as supplemental
heat. Use this heater along with
your primary heating system. Do
not install this heater as your
primary heat source. If you have a
central heating system, you may
run system's circulating blower
while using heater. This will help circulate the heat throughout the
house.
Front View
WARNING: A qualified service
person must install heater. Follow
all local codes.
WARNING: Never install the
heater
l in a bedroom or bathroom
l in a recreational vehicle
l where curtains, furniture, clothing,
or other flammable objects are
less than 42 inches from the
front, top, or sides of the heater
l in high traffic areas
l in windy or drafty areas
Figure 4 -Minimum Clearance to Wall and Ceiling
IMPORTANT: Vent-free heaters add
moisture to the air. Although this is
beneficial, installing heater in rooms
without enough ventilation air may
cause mildew to form from too much
moisture. See Air for Combustion and
Ventilation, pages 5 through 6.
CAUTION: This heater creates
warm air currents. These currents
move heat to wall surfaces next to
heater. Installing heater next to vinyl
or cloth wall coverings or operating
heater where impurities (such as
tobacco smoke, aromatic candles,
cleaning fluids, oil or kerosene lamps,
etc.) in the air exist, may discolor
walls.
CHECK GAS TYPE
Use only the type of gas indicated on
the plate. If your gas supply can not
meet that requirement, do not install
heater. Call the dealer where you purchased heater, for the proper type of
heater.
CLEARANCES TO COMBUSTIBLES
(Vent-Free Operation Only)
Carefully follow the instructions below.
This fireplace is a freestanding unit
designed to set directly on the floor.
WARNING: Maintain the minimum clearances. If you can, provide greater clearances from floor,
ceiling, and adj oin ing side and
back walls.
7
IMPORTANT: You must maintain
minimum wall and ceiling clearances
during installation. The minimum
clearances are shown in Figure 4.
Measure from outermost point of stove
top.
Minimum Wall and Ceiling Clearances
(see Figure 4)
A. Clearances from outermost point
of stove top to any combustible side
wall should not be less than 12
inches.
B. Clearances from the stove top to
the ceiling should not be less than
48 inches.
INSTALLATION
Continued
CONNECTING TO GAS
SUPPLY
WARNING: A qualified service
person must connect heater to gas
supply. Follow all local codes.
CAUTION: Never connect heater
directly to the gas supply. This heater
requires an external regulator (not
supplied). lnstall the external regulator between the heater and gas
supply.
INSTALLATION ITEMS NEEDED
Before installing heater, make sure
you have the items listed below.
l piping (check local codes)
l sealant (resistant to propane/LP gas)
l equipment shutoff valve*
l test gauge connection**
l sediment trap
l tee joint
l pipe wrench
l Flexible Gas hose(check local code)
* A CSA design-certified equipment
shutoff valve with 1/8 " NPT tap is
an acceptable alternative to test
gauge connection. Purchase the
o p t i o n al C S A d esig n - c ertif ied
equipment shutoff valve from your
dealer. See Accessories.
The installer must supply an external
regulator. The external regulator will
reduce incoming gas pressure. You
must reduce incoming gas pressure
to between 11 and 14 inches of water.
If you do not reduce incoming gas
pressure, heater regulator damage
could occur. lnstall external regulator
with the vent pointing down as shown
in Figure 6. Pointing the vent down
protects it from freezing rain or sleet.
CAUTION: Only use a new black
iron or steel pipe. Internally-tinned
copper tubing may be used in
certain areas. Check you local
codes. Use pipe of 1/2" diameter or
greater to allow proper volume gas
to heater. If pipe is too small, undue
loss of pressure will occur.
Installation must include an equipment shutoff valve, union, and
plugged 1/8" NPT tap. Locate NPT
tap within reach for test gauge hook
up. NPT tap must be upstream
from heater (see Figure 7).
Propane/LP
Supply Tank
WARNING: Never connect
heater to private (non-utility) gas
wells. This gas is commonly known
as wellhead gas.
Front View
Figure 5 -Gas Regulator Location
and Gas Line Access Into Stove
Cabinet
IMPORTANT: Inst all equ ipment
shutoff valve in an accessible location.
The equipment shutoff valve is for
turning on or shutting off the gas to
the appliance. Apply pipe joint sealant lightly to male threads.This will
prevent excess sealant from going
into pipe. Excess sealant in pipe could
result in clogged heater valves.
CAUTION: Use pipe joint
sealant that is resistant to gas
(PROPANE or NG).
W e recommend that you install a
sediment trap in a supply line as
shown in Figure 7. Locate sediment
trap where it is within reach for cleaning.
Install in the piping system between
fuel supply and heater. Locate sediment trap where trapped matter is not
likely to freeze. A sediment trap traps
mo istu re and c ont amin ants. Th is
keeps them from going into heater
controls. If sediment trap is not installed or is installed incorrectly,
heater may not run properly.
CAUTION: Avoid damage to
regulator. Hold gas regulator with
wrench when connecting into gas
piping and/or fittings.
WARNING: Do not over
tig hten g as con nectio ns.
Figure 6 -External Regulator With
Vent Pointing Down
NG Models:
5” to 10.5” W.C.
Gas supplier provide external
regulator for natural gas
Figure 7 -Gas Connection
* Purchase the optional CSA design-certified equipment shutoff valve
from your dealer. See Accessories.
** Minimum inlet pressure for purpose of input adjustment.
8
INSTALLATION
Continued
CHECKING GAS CONNECTIONS
WARNING: Test all gas piping
and connections for leaks after
installing or servicing. Correct all
leaks immediately.
Pressure Testing Gas
Supply Piping System
WARNING: Never use an open
flame to check for a leak. Apply a
mixture of liquid soap and water to
all joints. Bubbles forming show a
leak. Correct all leaks immediately.
CAUTION: Make sure external
regulator has been installed between gas supply and heater. See
guidelines under Connecting to Gas
Supply (page8).
Pressure Testing Heater
Gas Connections
Test Pressures Equal To or
Less Than 1/2 PSIG(3.5 kPa)
1. Close equipment shutoff valve
(see Figure 8).
2. Pressurize supply piping system
by either using compressed air or
opening gas supply tank valve.
3. Check all joints from gas meter to
equ ipment shut off valve(see
Figure 9). Apply mixture of liquid
soap and water to gas joints.
Bubbles forming show a leak.
4. Correct all leaks immediately.
1. Open equipment shutoff valve
(see Figure 8).
2. Open gas supply tank valve.
3. Make sure control knob of heater is
in the OFF position.
4. Check all joints from equipment
shuto ff valve t o control valve
(Figure 9). Apply mixture of liquid
soap and water to gas joints.
Bubbles forming show a leak.
5. Correct all leaks immediately.
6. L ig ht heat er (see O pe ra t in g
Heater, page 10).Check all other
internal joints for leaks.
7. Turn off heater (see Operation of
Turn-Off , page 10).
Test Pressures In Excess Of 1/2
PSIG(3.5kPa)
1. Disconnect
heater with its
appliance main gas valve (control
valve) and equipment shutoff valve
from gas supply piping system.
Pressures in excess of 1/2 psig
will damage heater regulator.
2. Cap off open end of gas pipe
where equipment shutoff valve
was connected.
3. Pressurize supply piping system
by either using compressed air or
opening gas supply tank valve.
4. Check all joints of gas supply
piping system. Apply mixture of
liquid soap and water to gas
joints. Bubbles forming show a
leak.
5. Correct all leaks immediately.
6. Reconnect heater and equipment
shutoff valve to gas supply. Check
reconnected fittings for leaks.
Figure 8 -Equipment Shutoff Valve
Figure 9 -Checking Gas Joints
9
INSTALLATION
Continued
INSTALLING LOGS
WARNING: Failure to position
the parts in accordance with these
diagrams may result in property
damage or personal injury.
CAUTION: After installation
and periodically thereafter, check to
ensure that no flame comes in
contact with any log. With the heater
set to High, check to see if flames
contact any log. If so, reposition logs
according to the log installation
instructions in this manual. Flames
contacting logs will create soot.
IMPORTANT: Make sure log does not
cover any burner ports (see Figure 10).
Figure 10 -Installing One-Piece Log
Set (Top View)
WHAT TO DO IF YOU SMELL GAS
SEE WARNING in Page 1 for proper
instructions.
C. Use only your hand to push in
control knob. Never use tools. If the
the appli ance could not operate , don't
try to repair it, Call a qualified service
technician or gas supplier.Forced or attempted re-pair may result in a fire or
explosion.
D. Do not use this appliance if any
part has been under water. Immediately call a qualified service technician to inspect the appliance and to
replace any part of the control system
and any gas control which has been
under water.
TO TURN OFF GAS TO APPLIANCE
Shut off heater
1. Press the IGN/OFF button.(see figure 12)
2. Set the Switch on OFF location.(see
figure 11)
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information,
page 3.
2. Make sure equipment shutoff
valve is fully open.
NOTE: W ait sixty(60) seconds to light
again after shutting off the heater.
NOTICE: During initial operation of new fireplace, burning logs
will give off a paper-burning smell.
Orange flame will also be present.
Open a window to vent smell. This
will only last a few hours.
CAUTION: Do not try to adjust
h eatin g levels b y usin g th e
equipment shutoff valve.
Shutting off burner only( pilot stay lit)
1.press the BURNER to set flame OFF
select
Also, see log placing instructions,
pages 22.
OPERATING
HEATER
FOR YOUR SAFETY
READ BEFORE LIGHTING
WARNING: If you do not
follow these instructions exactly, a
fire or explosion may result causing
property damage, personal injury or
A. This appliance has a pilot which
must be lighted by control system,
W hen lighting the pilot, follow
t h e s e i n s t r u c t i o n s e xac t l y.
B . BE FO RE LIGH TING sm ell all
around the appliance area for
gas. Be sure to smell next to the
floor because some gas is
heavier than air and will settle
on the floor.
E
Switch
Figure 11 Emergency Button and
ON/OFF Switch location
Fig 12 Front of the Transmitter
If your remote transimitter is lost or
m is-p lac ed , yo u c an p ress th e
emergency button to operate heater
manually on or off (see fig 11)
10
OPERATING FIREPLACE
Press BURNER button, the flame
is on “MAN” select. At this selection,
the main burner will keep working no
matter what the temperature is set at.
If there is a need to shut off the main
burner, just press the “BURNER”
button to make the burner
on the
Continued
c.shut off the main burner:
Fig15 Control board
nOPERATIONS OFn
BURNER
1.Plug-in 110V electrical outlet, you
Fig 13 Back of the Transmitter
nOPERATIONS OFn
REMOTE TRANSMITTER
1.Install three AAA SIZE batteries in the
battery holder.
The initial start-up on the LCD is: SET
TEMP is 77°F, ROOM TEMP is 77°F,
clock is AM12:00, burner is on “OFF”
select, and fan is on “AUTO” select. Di-
will hear a high pitch sound and
power light
(red) on the door will be lit that indicates that the burner is ready to be
make sure that the appliance is
connected to the gas supply, then
continue to the next step.
2.Point directly the remote transmitter
to the burner. Press ING/OFF button,
the electric spark starts igniting the
Please check the gas connection.
There are three selections: “AUTO”
“MAN” and “OFF”
a.auto select of main
burner:
Press BURNER button, the flame
2.Clock setting: Press CLOCK button on
the remote transmitter panel to select
item (hour, minute). The selected item
is flashing. Press ▲ or ▼ to change to
the correct actual hour(s); Press ▲ or
▼ to change to the correct minute(s),
is on “AUTO” select. Press ▲ or ▼ to
set temperature. If the room temperature is two degree lower than the set
temperature on the remote, the main
burner will turn on until the surrouding
temperature is two degree higher than
the set temperature. Once it reaches
temperature on the remote, the main
burner will automatically shut off.
then press CLOCK button again, time (Note: on the auto select of main
burner, the main burner does not
setting is finished.
3. When in operation, point the remote respond imm-ediately to the set
temperature until about one minute
transmitter to the remote receiver on the
burner in a maximum distance of 20 feet
without any obstruction between them.
Note:The thermostat sensing bulb
measures the temperatture of air naer
the heater cabinet. This may not always agree with room temperature
(depending on housing construction,
installation location,room size,openair
temperatures,etc.)Frequent use of
your heater will let you determine your
o wn
c o mfort
levels.
operated. Before plugging in the outlet
pilot and operation light (green) on the door
vide Points of hour and minute are flash- will be lit. Wait five (5) minutes to clear
ing (i.e. the timer is operating).
out any air. If you smell gas. STOP!
Fig 14 Initial start-up on the LCD
the main burner is on “OFF”
selection,.The main burner will shut
b.manual select of main
burner:
11
nOPERATIONS OFn
TIMING
1.Auto on:
when the burner is in a state of
readiness. Transmitter and burner is
off. Press TIMER button. Then press
▲ or ▼ change to the scheduled
time, then press the TIMER button
again, the TIMER starts timing and
the TIMER is flashing and the
operation light(green) begin
flashing. W hen the timer goes on the
scheduled time, the burner opens
automatically.
2.Auto off:
when the burner is in operation,
press TIMER button. Then press ▲
or ▼ to change to the scheduled
time, then press the TIMER button
again, the TIMER starts timing and
the TIMER is flashing and the
nOPERATIONS OFn
TURN-OFF
1.Manual turn-off: when the heater is
in operation, press the ING/OFF
button to shut off the heater.
2.Auto turn-off: refer to the second
step of “Operations of Timing”.
OPERATING FIREPLACE
Continued
nOPERATIONS OFn
KEY-PRESS LOCKING
1.Key press locking:
when the burner is in operation or the
transmitter is in a state of readiness,
just press LOCK button on the
operating
panel, there will be a “ ” symbol on
the LCD. If any button is pressed
now, the burner will not react at all.
2.Key-press unlocking:
when the burner is in a state of keypress locking, first press ▼ , then
press LOCK button to unlock it (Child
proof-See Fig12)
nOPERATIONS OFn
FAN
There are three selections :
“AUTO”“MAN”and “OFF”.When pushing
the“FAN” button on the “AUTO” select,
the fan will be controlled by the thermostat on the fan blower unit. On the
“MAN” select, the fan will be kept in
operation.To stop the operation, push
the “FAN”button to “OFF”select.(See
Fig12).
2.Check that gas supply to heater is on.
3.Remove the door on the right panel.
4. Push in gas control knob slightly and
turn clockwise
to the OFF position.
Shutting Off Heater
1. Turn control knob clockwise
to the OFF position.
NOTE: Knob cannot be turned form
“PILOT” to “OFF” unless knob is pushed
in slightly. Do not force.
S hu tti n g O ff Bu rne r O nl y
(Pilot Stays Lit)
Turn control knob clockwise
to the PILOT/IGN position.
NOTE: If power is on, you can oper-
5. W ait five (5) mintues to clear out any
air. Then smell for gas,including near
the floor. If you smell gas.STOP! Follow
“B” in the safety information on the side
of the heater.If you do not smell gas, go
to the next step.
ate the fireplace by transmitter.
6. Push in gas control slightly and turn
counterclockwise
to “PILOT” and
depress for five (5) seconds.
PROCEDURE
Control
LIGHTING
INSTRUCTIONS
1. STOP! Read the safety information
on the plate with heater.
Press in and rotate control knob
clockwise
to ELECTRIC posi-
tion after shutting off the fireplace.
nMANUAL LIGHTINGn
1. Follow steps 1 through 5 under
Lighting Instructions.
NOTE: The first time that the heater is
operated after connecting the gas
supply, the control knob should be
depressed for about thirty (30) seconds.
This will allow air to bleed form the gas
system.
7. With control knob pressed in,push
down and release the ignitor button
until pilot lights.
8. Keep control knob depressed for ten
(10) seconds after lighting pilot. If pilot
goes out ,repeat steps 5,6,7.
Manual
nTO TURN OFFn
GAS TO APPLIANCE
9. To turn on main burner partially press
down the control knob slightly and
rotate conterclockwise
.Release
2. W ith control knob pressed in,
strike match. Hold match to pilot
until pilot lights.
3. Keep control knob pressed in for
30 seconds after lighting pilot.
After 30 seconds, release control knob. Follow step 8 under
Lighting Instructions.
4.After completion of the abovementioned three steps, the trans
-mitter is kept in a state of
read i n ess. If t h e ap p l ian c e
doesn’t working for a period
time, just pull out the plug from
the 110V electrical outlet.
the down ward pressure on the knob
while continuing to turn until the knob
locks at the “ON” desired setting
position. Do not operate between
locked positions.
Fig16 Manual Control
12
OPERATING FIREPLACE
Continued
BURNER FLAME PATTERN
Figure 17 - Correct Flame Pattern
Figure 19 shows a correct burner flame
pattern. Figure 20 shows an incorrect
burner flame pattern. If burner flame
pattern is incorrect,
l shut heater off (see to shut Off Gas
to
Appliance, page 10)
l see Troubleshooting, pages 15
through 16
Caution: Lab le all w ires prior to
d i s c o n n e c t i o n w h e n s e r vi c i n g
controls. W iring errors can cause
improper and dangerous operations.
Verify proper operation after servicing.
DISCONNECT WIRNG OR CONTROL
MODULE
1. Remove four screws from the rear
control panel , take out thermostat
sensing bulb from the clip, then disconnect the wires to free to control
module from its mounting location .
Note: Do not confuse the mark on
the each wire.
Figure 19-Correct Flame Pattern
With Control Knob Set to High Flame
2. Remove two screws and hex nuts,
take out the control module. When
installing , reverse the steps above.
(See Figure 22 and Figure 25)
Figure 18 - Incorrect Flame Pattern
INSPECTING BURNERS
C h ec k p ilo t f lam e p a tte rn a n d
burner flame patterns often.
Figure 20 - Incorrect Flame Pattern
With Control Knob Set to High Flame
Figure 22- Control Model
PILOT FLAME PATTERN
Figure17 shows a correct pilot flame
pattern. Figure18 shows an incorrect
pilot flame pattern. The incorrect pilot
flame is not touching the thermocouple.
This will cause the thermocouple to
cool. W hen the thermocouple cools,
the heater will shut down.
If pilot flame pattern is incorrect, as
shown in Figure 18:
l Shut off fireplace .
l See Troubleshooting, pages 15
through 16 .
DISCONNECT FAN
1.
Remove screws from the fan
bracket panel , pull the fan bracket
panel out to remove. Then disconnect two wires to free fan.
2.
Mark or tag each wire removed
for its exact reconnection. Remove
Figure 21 - Injector Holder On
Outlet Burner Tube
the four screws from the fan .when
CLEANING AND MAINTENANCE
(See Figure 23 and Figure 25 )
installing , reverse the steps above.
WARNING: Disconnect power before attempting any maintance or
cleaning to reduce the risk of fire , electric shook or personal injury. Turn off
heater and let cool before cleaning.
Figure 23- Fan
13
CLEANING AND MAINTENANCE
Continued
C A U T IO N : Yo u m u st k ee p
c on tro l areas, b u rn er, an d
c irc u lat in g air p assag ew ays o f
h eater c lean . In sp ect th ese
areas of heater before each
u se. H ave h eater insp ec ted
yearly by a qualified service person.
Heater may need more
frequent cleaning due to
e xc es si ve li n t f ro m c ar p e t i n g ,
b ed ding m at erial, p et h air, etc .
CLEANING ODS/IGNITOR AND
BURNER
Clean with a vacuum cleaner.
CLEANING BURNER
INJECTOR HOLDER AND
PILOT AIR INLET HOLE
We recommend that you clean the unit
every three months or after 2500 hours
of operation. We also recommend that
you keep the burner tube and pilot assembly clean and free of dust and
dirt. To clean these parts we recommend using compressed air no greater
than 30 PSI. You can use a vacuum
cleaner in the blow position. If using
compressed air in a can, please follow the directions on the can. If you
don't follow directions on the can, you
could damage the pilot assembly.
1. Shut off the unit, including the
pilot. Allow the unit to cool for at
least thirty minutes.
2. Inspect burner, pilot and primary air
inlet holes on injector holder for
dust and dirt (see figure 21).
3. Blow air through the ports/slots
and holes in the burner.
4. Check the injector holder located
at the end of the burner tube
again. Remove any large particles
of dust, dirt, lint, or pet hair with a
soft cloth or vacuum cleaner
nozzle.
5. Blow air into the primary air holes
on the injector holder.
6. In case any large clumps of dust
have now been pushed into the
burner, repeat steps 3 and 4.
Clean the pilot assembly also. A
yellow tip on the pilot flame
indicates dust and dirt in the pilot
assembly. There is a small pilot air
inlet hole about two inches from
where the pilot flame comes out of
the pilot assembly (see Figure 24).
With the unit off, lightly blow air
through the air inlet hole. You may
blow through a drinking straw if
compressed air is not vailable.
Figure 24 -Pilot Air Inlet Hole
Figure 25-
14
CABINET
Air Passageways
l Use a
vacuum cleaner or
pressurized air to clean.
Exterior
l Use a soft cloth dampened with a
mild soap and water mixture. Wipe
the cabinet to remove dust.
LOGS
l If you remove logs for cleaning,
refer to Installing Logs (page 10)
to properly replace logs.
l Replace logs if broken or chipped
(dime-sized or larger).
MAIN BURNER
Periodically inspect all burner flame
holes with the heater running. All
slotted burner flame holes should
be open with yellow flame present. All
round burner flame holes should be
o p e n w ith a s m a ll b lu e flam e
present. Some burner flame holes
may become blocked by debris or
rust, with no flame present. If so,
turn off heater and let cool. Either
remove blockage or replace burner.
B lo c k ed b u rn er f lam e h o les w ill
create soot.
TROUBLESHOOTING
WARNING:Make sure that power
is turn off before proceeding....
OBSERVED PROBLEM
No spark when press in ignition button
W hen pressing the button of ignitor
button is pressed, there is spark at
ODS/pilot but no ignition
WARNING: Turn off and let cool
before servicing. Only a qualified
service person should service and
repair fireplace.
CAUTION: Never use a wire,
needle, or similar object to clean
ODS/pilot. This can damage ODS/
pilot unit.
REMEDY
POSSIBLE CAUSE
1. No power to heater
2. No battery in transmitter or battery
isn’t correctly assembly
1. Check the electric power.
2. Place or replace the battery.
1. Gas supply turned off or equipment
shut off valve closed
2. Air in gas lines when installed.
1. Turn on gas
3. Depleted gas supply
4. ODS/pilot is clogged
supply or open equip-
ment shutoff valve.
2. Press ON/OFF button again until
air is removed .
3.Contact
local gas company.
4 Clean ODS/pilot (see Cleaning
and Maintenance,page 13 ) or
replace ODS/pilot assembly.
5. Gas regulator setting is not correct
6. Pilot electrude position is not
correct
7. W ire is not correct or loosen
8 Gas valve is damage
5.
ODS/pilot lights but flame is continuous igniting and the main burner
couldn’t be lit.
1. Thermocouple connection loose
at control board
2. Pilot flame not touching
thermcouple which allows thermocouple to cool, causing pilot
flame to go out. This problem
could be caused by one or both of
the following
A) Low gas pressure
B) Dirty or partially clogged
ODS/ pilot
3. Thermocouple damaged
4. Control valve damaged
1. Hand tighten until snug, then
tighten 1/4 turn more.
2. A) Contact local gas company.
B) Clean ODS/pilot (see Cleaning
and Maintenance, page 13) or
replace ODS/pilot assembly.
3. Replace thermocouple.
4. Replace control valve.
Burner does not light after ODS/pilot
is lit
1. Burner orifice clogged
2. Inlet gas pressure is too low
3. Burner orifice diameter is too
sm all
4. Thermocouple leads disconnected or improperly connected
5. Burners will not come in
remote position
1.Clean burner (see Cleaning
and Maintenance, page 12) or
replace burner orifice.
2. Contact local propane/LP
gas company
3. Replace burner orifice
4. Reconnect leads (see wiring
diagram)
5. Replace battery in transmitter
and receiver
15
Replace gas control.
6. Replace Pilot.
7. Check the wire and make wire
correct.
8. Replace gas valve.
TROUBLESHOOTING
Continued
Delayed ignition burner
1. Manifold pressure is too low
2. Burner orifice clogged
1. Contact local gas company.
2. Clean burner (see Cleaning and
Maintenance, page 13).
Burner backfiring during combustion
1. Damaged burner
2. Gas regulator defective
1.Clean burner orifice (see Cleaning
and Maintenance, page 13).
2.Replace gas regulator.
Slight smoke or odor during initial
operation
1. Residues from manufacturing
processes
2. Not enough air
3. Gas regulator defective
1.Problem will stop after a few hours
of operation.
2.Check burner for dirt and debris. If
found, clean burner (see Cleaning
and Maintenance, page 12)
3. Replace gas regulator
Dark residue on logs or inside of
fireplace
1. Improper log placement
2. Air holes at burner inlet blocked
3. Burner flame holes blocked
1. Properly locate logs (see installing
logs, page 22).
2. Clean out air holes at burner inlet.
Periodically repeat as needed.
3. Remove blockage or replace burner
Heater produces a clicking/ticking
noise just after burner is lit or
shut off
1. Metal expanding while heating
or contracting while cooling
1. This is common with most heaters.
If noise is excessive, contact qualified service person.
SPECIFICATIONS
GFP2816R
GFP2818R
GFP2820R
Btu(Variable)
Gas Type
Ignition
Manifold Pressure
Inlet Gas Pressure
(In. of water)*
Maximum
Minimum
Dimensions, Inches (H×W ×D)
Heater
Carton
Weight, lbs
Stove
Shipping
voltage
watt
28,000
LP Gas
Automatic
8"W.C.
14"
11"
GFN2815R
GFN2817R
GFN2819R
28,000
Natural Gas
Automatic
3"W.C.
10.5"
5"
36 1/4”×45 1/2”×12 3/16”
42”×48 9/16”×13 7/16”
36 1/4”×45 1/2”×12 3/16”
42”×48 9/16”×13 7/16”
101
120
120
101
120
120
32
32
*For purposes of input adjustment
16
REPLACEMENT PARTS
REPLACEMENT PARTS
NOTE: Use only original replacement
parts. This will protect your warranty
coverage for parts replaced under
warranty.
PARTS UNDER WARRANTY
Contact authorized dealers of this
product. If they can't supply original
rep lac em en t p art(s), call KO ZYW ORLD’S Technical Service Department at (814)643-1775 for referral information
W hen calling KOZY-W ORLD or your
dealer, have ready:
l Your name
l Your address
l Model and serial numbers
of your heater
l How heater was malfunctioning
l Type of gas used (propane/LP or
NG)
l Purchase date
Usually, we will ask you
to return the defective part to the
factory.
PARTS NOT UNDER
WARRANTY
Contact authorized dealers of this
product. If they can’t supply original
replacement part(s) call KOZYW ORLD’S Technical Service Department at (814)643-1775 for referral information
W hen calling KOZY-W ORLD, have
ready
l Model number of your heater
l The replacement part number
ACCESSORIES
Purchase these heater accessories
from your local dealer. If they can not
supply these accessories, call KOZYW ORLD’S Technical Service Department at (814)643-1775 for referral
information. You can also write to the
address listed on the front page of
this manual.
EQUIPMENT SHUTOFF VALVE
Equipment shutoff valve with 1/8"
NPT tap.
FLEXIBLE GAS HOSE
l Flexible gas hose is used for
connecting the heater to gas supply.
l The flexible gas hose must be
CSA approved.
17
ILLUSTRATED
PARTS BREAKDOWN
GFN2815R
GFP2816R
GFN2817R
GFP2818R
GFN2819R
GFP2820R
18
PARTS LIST
GFN2815R
GFP2816R
GFN2817R
GFP2818R
GFN2819R
GFP2820R
This list contains replaceable parts used in your heater. When ordering
parts, follow the instructions listed under Replacement Parts on page 17
of this manual.
GFN2815R GFN2817R GFN2819R refer to NG column
GFP2816R GFP2818R GFP2820R refer to LP column
19
ILLUSTRATED
PARTS BREAKDOWN
GFN2815R
GFP2816R
GFN2817R
GFP2818R
GFN2819R
GFP2820R
20
PARTS LIST
GFN2815R
GFP2816R
GFN2817R
GFP2818R
GFN2819R
GFP2820R
This list contains replaceable parts used in your heater. When ordering
parts, follow the instructions listed under Replacement Parts on page 17
of this manual.
GFN2815R GFP2816R refer to WHITE column
GFN2817R GFP2818R refer to CHERRY column
GFN2819R GFP2820R refer to OAK column
21
LOGS INSTALLATION INSTRUCTIONS
1. All logs. See FIG(1).
STEP 1: Install the log 1on the angle iron.
See FIG(2).
FIG(1)
FIG(2)
STEP 2:Install the log 2 on the right rear STEP 3:Install the log 3 on the front angle.
See FIG(4).
iron. See FIG(3).
FIG(3)
STEP 4:Insert the pinhole on the upper
part on the left side of log 1. Place the
lower part of log 4 on the flat roof at the
left side of log 3. See FIG(5).
FIG(4)
STEP 5:Insert the pinhole on the upper
part of log 5 in the pin on the log 2.oPlace
the lower part of log 5 on the flat roof at
the left side of log . See FIG(6).
FIG(6)
FIG(5)
22
Mantel Installation Instructions
23
Assemble the Base
1. Set top base panel on the ground, with the surface marked 1 upward. Set connectors in
four screwed holes in the top base panel ( Note: Be sure to fasten the connectors tightly)See FIG (a).
Connector
FIG (a)
2. Piece together the left base panel marked 2 that has two holes with the top base panel. Note:
Insert the connectors on the left part of top base panel in the corresponding holes of left base
panel-see FIG (b). Then screw down the connectors using Philips screwdriver, see FIG (c).
Fastener
Connector
FIG (b)
FIG (c)
3. Piece together the right base panel marked 3 that has two holes with the top base panel. Note:
Insert the connectors on the right part of top base panel in the corresponding holes of right base
panel-see FIG (d). Then screw down the connectors using Philips screwdriver, see FIG (e).
Fastener
Connector
FIG (d)
FIG (e)
24
4. Set top base panel on the ground, with the surface marked 1 upward. Set connectors in
seven screwed holes in the top base panel (Note: Be sure to fasten the connectors tightly),
See FIG (f).
Connector
FIG (f)
5. Piece together the assembled structure and front base panel marked 4. Note: Insert the
connectors on the front base panel in the seven corresponding holes of assembled structure-see FIG (g). Then screw down the connectors using Philips screwdriver, see FIG (h).
Fastener
Base
FIG (g)
FIG (h)
Connector
Assemble Base to Mantel
Push base finished in step 5 to mantel to complete the whole installation procedure,
see FIG(i).
FIG (i)
25
Installation Instructions of Mantel and Fireplace
Note: The fireplace is quite big and heavy. For your safety, at least two people are needed
to install the fireplace to avert tilting.
Install fireplace in the desired position. Install two brackets at the fixed place with six 5×35
self-tapping screws and anchors as shown in FIG (1), assembling the anchors see page
27.Tear the dust-proof plastic film off regulator. Connect one end of hose metal fitting (provide
with fireplace) to regulator and the other end to the relevant valve of inlet tube (the connection means of metal hose, heater and inlet tube are mentioned in heater instructions). Then
fit mantel and fireplace and make sure the angle iron on mantel back should insert in the
bracket on wall, see FIG (2).
775 (301/2”)
FIG (1)
26
FIG (2)
Install base Push base to mantel and ensure the rear part of the base fits with the column face closely, see FIG (3).
FIG (3)
27
ASSEMBLING ANCHOR
1. To ensure the assembling position of anchor per FIG (1), use the hole of anchor to mark the
position of screw on the wall and then move the anchor away.
2. Attaching to Wall Stud Method
For attaching bracket to wall studs
a. Drill holes at marked locations using 9/64" drill bit.
b. Place bracket onto wall. Line up last hole on each end of bracket with holes drilled in
wall.
c. Insert mounting screws through bracket and into wall studs.
d. Tighten screws until bracket is firmly fastened to wall studs.
Attaching to Wall Anchor Method
For attaching bracket to hollow walls (wall areas between studs) or solid walls (concrete
or masonry)
a. Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or
masonry), drill at least 1" deep.
b. Fold wall anchor as shown in Figure 4 below.
c. Insert wall anchor (wings first) into hole. Tap anchor directly into the wall.
d. For thin walls (1/2" or less), insert red key into wall anchor. Push red key to pop open
anchor wings (see Figure 5).
Figure 4 - Folding Anchor
Figure 5 - Popping Open Anchor Wing For Thin Walls
e. Place bracket onto wall. Line up last hole on each end of bracket with wall
anchors.
f. Insert mounting screws through bracket and into wall anchors.
g. Tighten screws until bracket is firmly fastened to wall.
IMPORTANT: Do not hammer key! For thick walls (over 1/2" thick) or solid
wall,do not pop open.
28