Tiffin Motorhomes Zephyr 2007 Motorhome Owner's Manual

Tiffin Motorhomes Zephyr 2007 Motorhome Owner's Manual

Below you will find brief information for Motorhome Zephyr 2007. This manual provides instructions for safe and effective operation, maintenance, and troubleshooting of your new motor home. It covers various aspects including driving, safety, heating, air conditioning, major appliances and accessories, cabinets and furniture, structural features, towing hitch, electrical features, exterior features, interior features, plumbing and bath features, routine maintenance, and data charts.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Zephyr 2007 Owner's Manual - Tiffin Motorhomes | Manualzz
2007
Zephyr
Owner’s Manual
Tiffin Motorhomes, Inc.
105 2nd Street NW
Red Bay, AL 35582 U.S.A.
Phone: (256) 356-8661
E-Mail: [email protected]
[20060430]
Z E P H Y R
O W N E R ’ S
M A N U A L
5
Volume
TIFFIN MOTORHOMES, INC.
105 2nd Street NW Ø Red Bay, Alabama 35582 U.S.A.
Zephyr
Owner’s Manual
Z E P H Y R
O W N E R ’ S
M A N U A L
TIFFIN MOTORHOMES, INC.
Zephyr Owner’s Manual
© Tiffin Motorhomes, Inc.
105 2nd Street NW, Red Bay, AL 35582 U.S.A.
Telephone 256.356.8661 • Facsimile 256.356.8219
E-Mail: [email protected]
DISCLAIMER
Many of the features and appliances described in this manual may or may not be reflected in the
actual motor home purchased, depending on the options and models selected by the motor-home
owner. All items, materials, instructions, and guidance described in this manual are as accurate
as possible at the time of printing. However, because of Tiffin Motorhomes’ ongoing and
dedicated commitment to excellence, improvement of Tiffin’s motor homes is a continuing
process.
Consequently, Tiffin Motorhomes reserves the right to make substitutions and
improvements in its makes and models of motor homes without prior notification. Substitutions
of comparable or better materials, finishes, appliances, instrumentation, and instruction may be
made at any time it is deemed prudent to provide the customer with the best possible motor
home meeting the customer’s requirements.
Copyright © 2002 by Tiffin Motorhomes, Inc. – all rights reserved
Printed in the United States of America: First U.S. Printing: October, 2004
[20060430]
Z E P H Y R
O W N E R ’ S
M A N U A L
Table of Contents
Chapter 1
General Information
Fire Safety
2-9
Fire Extinguisher
2-9
Smoke Detector
2-10
Emergency Exit Window
2-10
Delivery
1-2
Parking Procedures
2-10
Dealer Responsibilities
1-2
Towing Hitch
2-11
Customer Responsibilities
1-2
Tiffin Motorhomes Limited Warranty
1-3
Major Equipment Manufacturers
1-3
Warranty Service
1-4
Owner’s Information Package
1-5
Customer Relations
1-5
Specification Labels
1-5
Furnace
3-2
Weighing Procedures for the Zephyr
1-7
Air-Conditioning System
3-3
Weight Distribution of the Motor Home
1-7
Thermostatic Controls
3-4
Liquid Propane (LP) Tank
3-4
LP Tank Filling Practices
3-5
LP Gas Regulator
3-6
CO/LP Gas Detector
3-7
Chapter 3
Heating & Air Conditioning
Chapter 2
Driving & Safety Instructions
Safety Considerations
2-2
General Warning
2-2
Prior to Departure
2-3
Driving
2-4
Fuels for the Motor Home
2-5
Refrigerator
4-2
Liquid Propane (LP) Gas System
2-6
Microwave/Convection Range
4-2
LP Gas Regulator
2-8
Air Filtration Fan
4-2
LP Distribution System
2-8
Cook Top and (Optional) Oven
4-3
TELEVISION SYSTEM OPERATION
4-4
Chapter 4
Major Appliances & Accessories
Recommended Precautionary Practices 2-8
ii
Z E P H Y R
O W N E R ’ S
M A N U A L
Television Antenna
4-4
General Information
7-2
Television Sets
4-5
Circuit-Breaker Boxes
7-3
Infrared Repeater
4-6
Auxiliary Start Switch
7-4
Audio-Video Control Console
4-6
Battery Inspection and Care
7-4
AM / FM / CD Stereo System
4-7
Battery Disconnect Panel
7-6
Home Theater System
4-10
120-Volt AC (VAC) Receptacles
7-7
Cable & Telephone Jack
4-10
12-Volt DC (VDC) Receptacles
7-8
Dishwasher (Optional)
4-11
Ground-Fault-Circuit Interrupt (GFCI)
7-8
Hydro-Hot Heating System
4-12
ICC Switch
7-8
CB Radio System Antenna Connection 4-13
Inverter / Converter
7-9
Rear-View Camera Monitor System
4-13
Automatic Generator Switch
7-9
Side-Mount Camera
4-14
Electrical Generator
7-11
Stacked Washer / Dryer
4-14
Automatic Transfer Switch
7-11
Carbon Monoxide/ LP Gas Detector
4-15
Resettable Circuit Breakers
7-12
Fuse Blocks
7-12
Seven-Pin Towing Connector
7-13
Chapter 5
Cabinets & Furniture
Chapter 8
Cabinets
5-2
Furniture
5-3
Bedroom Area
5-5
Slide-Out Features
Chapter 6
Structural Features
Chassis Features
6-2
Alignment
6-2
SLIDE-OUT OVERVIEW
8-2
General Considerations
8-2
Operating Precautions
8-2
Extending the Slide-Out Room
8-3
Retracting the Slide-Out Room
8-3
Manual Operation: Slide-Out Room
8-4
Manual Operation: X Slide Room Ext.
8-5
Chapter 9
Exterior Features
Chapter 7
Towing Hitch
Electrical Features
iii
9-2
Z E P H Y R
O W N E R ’ S
M A N U A L
Exterior Sides
9-2
Toilet
11-8
Security Lights
9-2
P-Traps
11-9
Roof & Ladder
9-3
Black-Water Holding Tank
11-9
Hydraulic-Leveling Jacks
9-3
Gray-Water Holding Tank
11-10
HWH Leveling Control System
9-4
Wastewater Disposal
11-10
Electric Steps
9-5
Sewer Connection and Camping
11-11
Mirrors
9-7
No-Fuss Flush
11-12
Exterior Shower
11-12
Chapter 10
Chapter 12
Interior Features
Construction Features
Bedspread
10-2
Flooring
10-2
Ceiling
10-3
Window Treatments
10-3
Construction Notes
12-2
Typical Floor Plan
12-2
Chapter 13
Chapter 11
Windows, Awnings, Vents &
Plumbing & Bath Features
Doors
FRESHWATER SYSTEM
11-2
Windows
13-2
Monitor Panel
11-2
Awnings
13-2
Kitchen Sink
11-2
Vents
13-4
Bath, Sink, Shower & Accessories
11-3
Doors
13-4
Water Pump
11-3
Keyless Lock
13-5
City Water Connection
11-4
Filling the Freshwater Tank
11-5
Sanitizing
11-5
Water Filter
11-6
Freshwater Lines
11-7
Plumbing Manifold
11-7
WASTEWATER SYSTEMS
11-7
General Information
11-7
Chapter 14
Routine Maintenance
iv
EXTERIOR CARE
14-2
Washing
14-2
Z E P H Y R
O W N E R ’ S
M A N U A L
Waxing
14-3
Motor Home Maintenance Record
15-7
Seals
14-3
Motor Home Maintenance Record
15-8
Proper Sealants for Application
14-4
Motor Home Maintenance Record
15-9
Striping and Decals
14-4
ALCOA Aluminum Wheel Care
14-5
Roof Care and Maintenance
14-5
Moisture Management
14-6
Tire and Tire Safety Information
14-10
Tire Pressure
14-24
INTERIOR CARE
14-27
Carpet
14-28
Fabrics
14-29
Walls and Ceiling
14-30
Dashboard
14-30
Woodwork and Floors
14-30
Countertops
14-31
Accessories
14-32
Detectors
14-32
Condensation
14-32
ROUTINE MAINTENANCE SCHEDULES 14-33
Monthly
14-34
Every Three Months
14-34
Every Six Months
14-34
Annually
14-34
Winterizing
14-35
De-Winterizing
14-36
Chapter 15
Maintenance & Data Charts
Motor Home Owner’s Data Sheet
15-2
Motor Home Maintenance Record
15-3
Motor Home Maintenance Record
15-4
Motor Home Maintenance Record
15-5
Motor Home Maintenance Record
15-6
v
G E N E R A L
I N F O R M A T I O N
Chapter
1
GENERAL INFORMATION
1-1
G E N E R A L
I N F O R M A T I O N
Tiffin Motorhomes: “Wherever you go, we go”
Delivery
Throughout the entire manufacturing process your Tiffin motor home has been regularly inspected by our
qualified personnel to assure you of the finest product of the highest quality, without exception. However,
the final inspection at our factory is not to be the last one. The pre-delivery inspection and system check that
your dealer performs are the final inspections done to your particular motor home prior to your actually
receiving your new Zephyr motor home. Your dealer is also available to assist you in understanding the
warranties and completing the necessary forms to activate the warranties for the various appliances and
accessories installed in your motor home.
Dealer Responsibilities
1. A pre-delivery inspection and systems check is performed to assure a thorough inspection of the
motor home and to assure the proper operation of all factory-installed components.
2. A customer walk-through is performed to familiarize the new customer with the motor home, its
systems and components, and their proper and safe operation.
3. Delivery of the Owner’s Information Package which contains warranty cards and registrations for
the vehicle and all factory-installed components from other vendors and suppliers to Tiffin
Motorhomes. The detailed operation instructions and maintenance instructions on these components
are also included in this package.
4. Assisting the customer in completing the registration forms to avoid loss of warranty coverage. The
dealer should review the limited-warranty provisions with the customer to stress the importance of
completing the warranty cards and registration forms for the components in the motor home to enable
the manufacturers to receive them within the prescribed time limits.
5. Providing the customer with information regarding warranty and non-warranty work on the
vehicle and its separately warranted components.
Customer Responsibilities
The customer is responsible for regular and proper maintenance of the motor home. Properly maintaining
your motor home will prevent conditions arising from neglect that are not covered by your Tiffin Motorhomes
limited warranty. The maintenance guidelines in this manual and any other, applicable manual(s) should be
followed. It is your responsibility and obligation to return the vehicle to an authorized dealer for repairs and
service.
To assist you in avoiding problems with your motor home, it is recommended that you do the following:
1-2
G E N E R A L
I N F O R M A T I O N
1.
Read the warranty. Go over it thoroughly with your dealer to make sure you understand all the
terms and conditions of the warranty.
2.
Inspect the motor home; do not accept delivery until after you have gone through the motor
home with the authorized Tiffin Motorhomes dealer. Ask questions about anything unfamiliar to
you.
3.
Please ask questions about anything you don’t fully understand about your Zephyr; Tiffin
Motorhomes is here to serve you and assure that you have all the information necessary for your
safe and enjoyable use of your new motor home.
4.
When you are taking delivery, set an appointment for adjustments. This appointment should be
within two weeks after you accept delivery.
5.
You are responsible for and expected to use your Zephyr in a responsible, safe manner. Please
take the time to familiarize yourself with the proper operation of the motor home and all its
features before you attempt to use your motor home.
Tiffin Motorhomes Limited Warranty
The Tiffin Motorhomes limited warranty was provided to you by your authorized Tiffin Motorhomes
dealer during the pre-delivery inspection. When you inquire about your Tiffin Motorhomes warranty,
please refer to this document. Should you need or desire an additional copy or other information, please
contact:
Tiffin Motorhomes, Incorporated
105 2nd Street NW
Red Bay, AL 35582 U.S.A.
Telephone: (256) 356-8661; Facsimile: (256) 356-8219
E-Mail: [email protected]
Tiffin Motorhomes will be pleased to send you an additional copy or any other information requested, as may
be warranted.
Major Equipment Manufacturers
The following list is a compilation of the vendors and suppliers of the major subsystems and components of
your Zephyr. This list is provided for your convenience and is not meant as a complete substitution of the
literature and accompanying “how to contact us” information supplied by those vendors and suppliers in your
1-3
G E N E R A L
I N F O R M A T I O N
Owner’s Information Package [see below for particulars]. Where appropriate, web-site information is provided
for computer users.
•
Atwood Mobile Products
(800) 646-8557
www.atwoodmobile.com
o CO Alarm
(800) 880-6788
www.atwoodmobile.com
o LP Gas Detector
(815) 877-5700
www.atwoodmobile.com
o LP Gas Water Heater (815) 877-5700
www.atwoodmobile.com
•
Denso Corporation
(248) 350-7500
www.globaldenso.com
•
Flexsteel Industries
(319) 556-7730
www.flexsteel.com
•
Heart Interface
(800) 446-6180
www.heartinterface.com
•
HWH Corporation
(800) 321-3494
www.hwhcorp.com
•
Kwikee
(541) 942-3888
www.kwikee.com
•
Norcold, Inc.
(800) 543-1219
www.norcold.com
•
Onan Corporation
(612) 574-5944
www.onanindiana.com
•
Panasonic Corporation
(800) 211-7262
www.panasonic.com
•
Power Gear
(800) 334-4712
www.powergear.com
•
Sharp Corporation
(800) 237-4277
www.sharp-usa.com
•
Suburban Manufacturing Co.
(423) 775-2131
www.suburbanmanufacturing.com
•
The Dometic Corporation
(219) 294-2017
www.dometic.com
For those wishing more information (e.g., locations of authorized subsidiaries), the following web site,
www.rvamerica.com/data/s_alist.htm, should be helpful. This site provides complete, alphabetic listings of
all suppliers and vendors for all contemporary recreational vehicles and motor homes.
Warranty Service
If any warranty service may be required, that service needs to be completed during the warranty period (basic
warranty: 12 months or 12,000 miles). Tiffin Motorhomes warrants its unitized construction for 10 years and
its laminations for 5 years. Any service work performed after the expiration of the Tiffin Motorhomes
warranties WILL NOT be covered by those warranties.
1-4
G E N E R A L
I N F O R M A T I O N
Exceptions may be made, on an individual basis, to this deadline on account of the unavailability of parts
and/or service appointment time where work is to be performed. However, don’t rely on the possibility of an
exception; please schedule any desired in-warranty work before your warranty expires.
Owner’s Information Package
The Owner’s Information Package (Figure 1-1) includes valuable documents about your Zephyr and its
components and systems. By consulting the booklets and instruction
manuals included in the Owner’s Information Package, you will learn
how to operate, maintain, and troubleshoot these items safely and
effectively. The Tiffin Motorhomes Zephyr Owner’s Manual does not
cover every possible detail of equipment—standard and/or optional—
installed on or in your vehicle.
Figure 1-1. Owner’s Information
Package
As with all valuable documentation, please keep them in a safe, secure
place for your later use and consultation. Please complete the warranty
registration form and return to Tiffin Motorhomes Inc. within five
working days. A stamped copy will be returned to you for your records.
Again, please keep this document in a safe, secure place for your later use
and consultation.
Customer Relations
If you wish to schedule maintenance or service or wish to order parts, you should notify your local authorized
Tiffin Motorhomes Dealership to set up an appointment. If you are unsure of the location of your nearest,
authorized Tiffin Motorhomes Dealership; please access the Tiffin Motorhomes website at
www.tiffinmotorhomes.com and then click on the “find a dealer” button, then click on the appropriate section
of the United States nearest your location, then select the closest dealer by clicking on that dealer’s number—
the dealer’s name, address, and telephone number will then be displayed for your use.
Specification Labels
There are two main numbers used to identify your Zephyr. The
Vehicle Identification Number (VIN) is the legal identification of the
completed vehicle. The VIN is the number used by the state for
vehicle identification and registration. Additionally, there is a Tiffin
Motorhomes serial number (Figure 1-2). The Tiffin number is
needed when you plan to make an appointment for service or
Figure 1-2. Tiffin Serial Number
ordering parts through your Tiffin Motorhomes Dealership or
Service Center. This number can be found on the side of the dashboard. A typical sample of this identification
label is shown in Figure 1-2.
Another label affixed to your Zephyr is the Recreational Vehicle Industrial Association (RVIA) Weight Label
(Figure 1-3) which is a required label for your vehicle. Tiffin Motorhomes, a manufacturer-member of RVIA,
has the obligation to disclose the following information, at minimum, to the purchaser of the motor home:
1-5
G E N E R A L
I N F O R M A T I O N
•
An indication of the contents of the RVIA weight label affixed
to the motor home.
•
A concise explanation of the following items:
o Vehicle Weight (VW) distribution.
o Proper weighing techniques to be used to weigh the
vehicle.
o Specific definitions for the following terminology:
ƒ Gross Vehicle-Weight Rating (GVWR) –
This is the maximum permissible weight of the
motor home when it is fully loaded.
ƒ Unloaded Vehicle Weight (UVW) – This is
Figure 1-3. RVIA Weight Label
the weight of the motor home, as built at the
factory, with full fuel, engine oil, and coolants. The UVW does not include cargo,
fresh water, LP gas, or any dealer-installed accessories.
ƒ Cargo-Carrying Capacity (CCC) – This is the maximum weight of all occupants
including the driver, personal belongings, food, fresh water, waste water, LP gas, tools,
tongue weight of towed vehicle [if any], dealer-installed accessories, and the like. The
CCC is equal to or less than the GVWR minus the UVW.
ƒ Gross Combination-Weight Rating (GCWR) – This is the value specified by the
chassis manufacturer as the maximum allowable loaded weight of the motor home
with a towed trailer and/or vehicle [if any].
ƒ Sleeping-Capacity Weight Rating (SCWR) – This is the maximum weight capacity
of the combined number of persons (i.e., number of people multiplied by 154 pounds
per person) permitted to sleep within the vehicle.
ƒ Gross Axle-Weight Rating (GAWR) – This is the maximum allowable weight for a
single-axle system, as measured at the tire-ground interfaces. The GAWR considers
the weakest link in the tire, wheel, brakes, hubs, axle, springs, and attaching parts. To
illustrate, if the axle is rated at 15,000 pounds and the tires are rated at 3,200 pounds
each as a dual installation; then the maximum GAWR would be 12,800 pounds for a
four-tire vehicle
•
Towing Guidelines – Specific weighing instructions and guidelines are furnished in the Owner’s
Manual (see below for a general overview and also in Chapter 2 for more specific details).
1-6
G E N E R A L
I N F O R M A T I O N
Weighing Procedures for the Zephyr
To weigh the motor home properly, the motor home should be level when the weighing process is performed.
Your Zephyr motor home has been designed and built in compliance with the recommended limits of the
major-component/system suppliers to provide a realistic CCC. However, it is up to the final user to provide
even distribution of the loads brought into the motor home to prevent uneven loading. Once the motor home
is loaded, it can be taken to any drive-on scales or individual-wheel scales to determine that the final weight is
within specified limits for the motor home. The procedure which can be used is as follows:
First, drive the motor home onto the scales so that all wheels are on the scales; this provides the gross vehicle
weight (GVW) of the motor home and can be recorded as such. The GVW should not exceed the GVWR
specified for the motor home. Second, drive the motor home so that the front wheels are off the scales and
only the rear wheels remain on the scales; this provides the total weight of the motor home, save for the front
axle. This weight should not exceed the total rating of the axles remaining on the scales. The front axle weight
is determined by subtracting the weight from the GVW that was obtained in the first step which was performed
earlier. The result should not exceed the listed front-axle weight rating. For a more thorough weighing of the
motor home, Chapter 14 contains more specific axle-weight determinations.
Weight Distribution Throughout the Motor Home
To assure the maximum stability of the motor home under static (i.e., parked) and dynamic (i.e., moving)
conditions, the distribution of the items to be carried and stored within the motor home and in the storage bays
underneath the motor home should be performed in such a manner to strive for reasonably even side-to-side
and front-to-rear dispersion of the entire weight of both the stored items and also the driver and expected
passenger(s) during transit. This process will assure that the motor home is not “lop-sided” in weight
distribution (i.e., all the stored weight on one side and/or mainly towards the front or the rear)—keeping a
center of mass of the motor home essentially centered on a front-to-rear and side-to-side basis will also provide
better control of the motor home when it is in motion.
1-7
D R I V I N G
&
S A F E T Y
I N S T R U C T I O N S
Chapter
2
Driving & Safety Instructions
2-1
D R I V I N G
&
S A F E T Y
I N S T R U C T I O N S
Safety Considerations
Prior to using your motor home, especially for the first time or after a long period of non-use, please read
thoroughly all the instructions in both the Owner’s Manual and the chassis-manufacturer’s manual before
attempting to operate your motor home. There are several safety considerations which you should realize and
follow while your Zephyr is in motion. These safety considerations, as well as others meant to preclude any
damage to the motor home, are listed in this chapter. Besides the driver, it would be helpful for the passengers
to be familiar with these safety considerations and precautions, too.
Warning
Before your motor home is to be operated, be sure that you have read the entire
Owner’s Manual and that you fully understand the equipment on your motor home and
how to use that equipment safely.
General Warning
Warning
Any portable, fuel-burning (e.g., charcoal, propane, butane, wood) equipment must not
be used inside the motor home. Any use of such equipment inside the motor home
may readily cause fires and/or asphyxiation by carbon-monoxide poisoning. Further,
such unauthorized use would probably invalidate your motor-home insurance policy.
In general, there are several “common-sense” safety precautions that should be taken every time the
motor home is to be used on the road; these precautions include:
•
Only seats with seat belts should be used while the motor home is in motion; those seat belts
should be worn by all people (driver, passengers) in the motor home at that time.
•
While the motor home is moving, lock all seats in the forward-facing position to provide
maximum safety for the users.
•
While the motor home is moving, no one inside should ever stand or kneel on seats (e.g., young
children).
2-2
D R I V I N G
&
S A F E T Y
I N S T R U C T I O N S
•
In the majority of states, it is the law that seat belts must be used (fastened snugly about the chest
and hip areas), anytime the motor home is in motion, to provide desired protection in the event
of a crash.
•
Any fire extinguisher(s) should be inspected on a monthly basis to assure that each extinguisher is
properly charged and ready for operation.
•
Any smoke and/or carbon-monoxide (CO)/Liquid Propane (LP) gas alarm(s) should be regularly
inspected and tested. If being used for the first time, the smoke and/or CO/LP gas alarm should
be properly activated and fresh batteries installed before the motor home is placed into service.
Prior to any trip, the smoke and/or CO/LP gas alarm(s) should be manually tested to assure their
correct operation. Immediately replace any defective components (e.g., weak batteries). Never
sleep in a motor home not having functional smoke and/or CO/LP gas alarm(s). Should an
alarm or detector fail when in transit, a suitable replacement can be purchased at most hardware
stores, superstores, or drug stores.
•
While the motor home is moving, the sleeping facilities are not to be used.
•
In the event of an emergency, be sure that everyone in the motor home is familiar with all escape
exits (doors, escape window). Do not use the emergency window as a routine exit; this is strictly
to be used for emergency purposes only. When the motor home is parked, be sure that the
emergency exits are not inadvertently blocked.
Prior to Departure
For your continued safety and convenience, the following is a representative “check list” designed to
assure your safety while driving:
•
Clean all windows, mirrors, and light lenses (front, back, side) to assure that you can “see” and
“be seen.” Reposition any mirrors or other fixtures to provide an unobstructed view (front, sides,
and back) from the driver’s seat (see Chapter 9 for details). When another driver takes over,
reposition the mirrors and other fixtures for that driver.
•
Remove or secure all loose exterior fixtures (e.g., awnings, flags, antennas, portable lights) to keep
them from falling from the motor home when the motor home is in motion.
•
Make a “walk-around” visual inspection of the motor home to note any irregularities (e.g., loose
trim) or problems (e.g., under/over inflated tires; abrasions or nicks on the tires); correct noted
problems accordingly.
•
Check all exterior storage-compartment and generator-compartment doors to make sure that they
are properly latched and locked. If need be, check inside all exterior compartments to make sure
that all cargo and equipment are properly secured so that they won’t work loose and become
hazards during sudden starts and stops.
2-3
D R I V I N G
&
S A F E T Y
I N S T R U C T I O N S
•
Check tires for proper inflation (i.e., cold inflation pressure: 100 psig or so); if the motor home
has not been used, make sure that the “cold inflation” pressure is maintained. If the motor home
has very recently been used, make sure that the “hot inflation” pressure (see the tiremanufacturer’s literature to determine appropriate “hot inflation” pressure) is maintained. All tire
pressures should be within 1-2 pounds (psig) of each other, unless weight loading dictates
otherwise (see Chapter 14, Section 14-5).
•
Examine wheel lug nuts to assure their proper tightness. If any lug nuts were found to be loose,
first check the fit of the wheel to the hub to make sure that the wheel is not mis-mounted which
would produce a “wobbly” wheel when the motor home is in motion, then tighten the lug nuts.
•
Check all fluid levels (e.g., engine oil, transmission fluid, coolant, power-steering fluid, brake fluid,
battery fluid [if applicable], windshield-washer solvent) to assure correct levels are maintained.
Fill any low reservoirs, as needed.
•
DO NOT SUBSTITUTE any other fluids for specified oils, transmission fluid, brake fluid, or
other hydraulic fluids—in most instances, substitutions are not acceptable and may void
warranties.
•
Prior to starting the motor-home engine, make sure that all lines (e.g., water, sewer) and electricalpower cords are disconnected and properly stowed.
•
Assure that the leveling jacks are in the “travel” position.
•
After entering the motor home, make sure that the electrically-actuated, retractable step has
properly operated to retract the step fully before starting the engine of the motor home.
Driving
Various adjustments need to be made to assure the driver’s comfort and the safety of the motor home before
starting and moving the motor home; these include:
•
The driver should adjust the driver’s seat, the tilt
steering, the exterior rear-view mirrors, and the
instrumentation panel lighting (if night-time) for the
driver’s comfort and safety. This is especially
important for first-time use so that the driver may
become accustomed to the “feel” of the motor home
and know where the various adjustments are located
“before the fact”; not after some need arises while the
motor home is in service.
•
The driver should be familiar with all gauges,
instruments, switches, and indicators on the instrument panel (Figure 2-1) prior to driving. Should the
driver encounter any “unknowns” on the panel, they should be investigated (via the Owner’s Manual or
Figure 2-1. Driver’s Instrumentation Panel
2-4
D R I V I N G
&
S A F E T Y
I N S T R U C T I O N S
Owner’s Information Package) prior to departure so that the driver fully understands these items and
their functions.
•
One should never adopt a “learn as you go” philosophy, as there are too many controls and switches to
be understood before the motor home is actually used. Please take the time to become thoroughly
familiar with the entire instrument panel prior to using the motor home on the road.
•
Do not operate the cruise-control function during any extreme weather situations (e.g., snow, ice, sleet,
heavy rain) or when road conditions are hazardous (icy, snowy, winding roads, city traffic) or when a
constant speed of the motor home is not possible or if traffic conditions don’t warrant such.
•
Avoid driving the motor home through any standing water. If deep enough, such water can wet the
brake pads and cause fading of the brakes (i.e., loss of braking power) and lead to excessive sliding or
pulling to one side or another.
•
If one has driven through standing water, at the first opportunity safely to do so, check the braking
action. If braking has degraded, lightly apply the brakes to allow the brake pads to dry—don’t use the
motor home when the braking function is significantly reduced.
•
Know the limits of operation of the motor home. Don’t try to achieve excessive speeds, climb overly
steep hills, traverse overly long grades, attempt to use the motor home as an “off-the-road” (OTR)
motor home, rapidly switch lanes, or rapidly accelerate or decelerate the motor home. When in doubt
about the handling characteristics of the motor home, consult your chassis manual for information.
Fuels for the Motor home
Your motor home is designed to have several types of petroleum-derived fuels used in
the routine operation of the motor home—these require prudent and safe handling to
assure safety of the motor home and its occupants; namely:
•
•
Anytime the motor fuel (i.e., diesel fuel, see Figure 2-2) or the LP tank (see
Figure 2-3) is to be filled, the motor home engine is to be turned “off,” all
pilot lights must be extinguished, and appliances turned “off.”
Figure 2-2. Fuel Tank
Fill Door
Further, during any filling operation or connecting/disconnecting of any LP
tanks, a NO SMOKING policy should always be observed. In a similar manner, any other comparable
devices of the motor-home users (e.g., butane camp-lights, propane lights and grills) should be treated
in a similar manner to assure the safety of all concerned.
2-5
D R I V I N G
&
S A F E T Y
I N S T R U C T I O N S
Warning
Liquid propane (LP) gas containers, gasoline, or
other flammable liquids are not to be placed or
stored inside the motor home because a fire or
explosion may occur. LP gas containers are
equipped with safety valves that may relieve
excess pressure by discharging gas into the
atmosphere—any containment of that vented LP
Figure 2-3. Liquid Propane Tank
gas constitutes an explosive hazard.
•
NEVER use an open flame to test for LP gas leaks or to examine the fluid levels in the fuel tanks.
•
After filling any LP system, immediately replace and secure all protective covers and caps.
•
After closing the LP valve, close and securely latch the LP door to prevent unintentional access or
damage.
•
NEVER connect natural gas to the LP gas system—LP gas and natural gas are not interchangeable.
•
NEVER use any other “burning” equipment (e.g., charcoal grills, wood stoves, butane lights, propane
lights inside the motor home—doing so may cause fires and/or asphyxiation.
Liquid Propane (LP) Gas System
A warning label is conspicuously located near the LP gas container (Figure 2-4); that label reads:
Warning
DO NOT FILL the LP Container(s) to more than 80% of capacity.
Any overfilling of the LP gas container(s) can result in uncontrolled gas flow—a prime condition for a fire or
explosion. The LP container should only be filled to 80% of its capacity; the remainder of the cylinder space is
vapor space to contain expansion of that liquid when subjected to varying ambient-temperature conditions.
Filling in excess of 80% of the liquid volume of the container reduces that vapor space and, thus, creates a
condition for possible over-pressurization of the container.
2-6
D R I V I N G
&
S A F E T Y
I N S T R U C T I O N S
All LP appliances in your motor home have been approved for use in motor homes by a nationally recognized
testing laboratory (i.e., UL and CSA certified). When properly used, LP gas is a clean-burning fuel which can be
dependably used. In actuality, the LP container contains liquid
propane under high pressure. The liquid, when it passes
through the tank valve to a lower pressure, vaporizes into a gas,
and then passes through a regulator to maintain a constant
pressure. This gas, then, is the actual fuel distributed through
the LP-gas manifold system to the LP-based appliances used in
your motor home.
LP-appliance-lighting problems are typically caused by an
Figure 2-4. Liquid Propane Tank
improperly adjusted gas regulator. NEVER attempt to adjust
or reset the gas regulator yourself, as an authorized service technician is needed to make these adjustments. As
a good preventive-maintenance activity, the regulator should be checked semi-annually by a service technician
and also before every extended trip.
Warning
When the motor home is not in use, be sure to close the main LP gas valve at the tank.
When the LP gas tank is to be refilled, close the main valve to preclude the chance of
the pilot lights possibly igniting fumes from the LP fuel. As some LP-gas appliances
(e.g., refrigerator, furnace, water heater) have Direct Spark Ignition (DSI) systems, it is
very important that these appliances be turned “off” when the LP gas is “off.” The DSI
boards will continue to work (i.e., generate an ignition spark) even when there is no LP
gas available.
Even though the LP-gas system is leak-checked and verified at the factory at the time of manufacture, normal
usage (travel vibrations, etc.) could loosen the fittings. Consequently, it is wise to check the gas fittings
periodically for leak tightness. One can daub some leak-detector solution (e.g., a “liquid-soap”-like solution) on
all the fittings, connections, and junctures when the system is under pressure. Should there be any leaks, small
bubbles will appear at any leak sites. Generally, loose fittings can be tightened (with “non-sparking” tools) to
stop the leaks. If this process doesn’t work, then one must shut off the main gas valve at the LP cylinder(s) and
immediately consult an authorized service technician to determine what repairs are necessary. Leaks may also
be detected by noting the sulfurous odor (i.e., rotten eggs) associated with LP gas [caused by an additive added
to the normally odorless LP gas]. DO NOT search for a leak by using a match or open flame.
2-7
D R I V I N G
&
S A F E T Y
I N S T R U C T I O N S
LP Gas Regulator
The LP gas regulator (Figure 2-5) is the most critical element of the LP-gas distribution system. The regulator
converts the high-pressure LP gas from the tank into a reduced-pressure LPgas supply suitable for use in the various appliances in the motor home. One
should regularly inspect visually the regulator system.
Figure 2-5. LP Gas Regulator
If any damage or corrosion is noted, contact an authorized service technician
to inspect and repair or replace the regulator. Do not attempt to adjust the
regulator yourself; the regulator has been pre-set at the factory. Only a
qualified LP service technician using specialized equipment should adjust
the regulator.
LP Distribution System
The primary LP distribution system in the motor home is a black, steel pipe manifold running the length of the
motor home. The secondary distribution lines running from this main distribution system are usually copper
tubing with flare fittings. If any of the gas lines break, do not attempt to splice them—always run new lines to
maintain the safety of the motor home. It is strongly recommended that only qualified service technicians
perform this work.
Remember, the main valve at the LP gas tank must be closed whenever any gas appliance is to be installed,
removed, or serviced—this process prevents LP gas leakage which could result in a possible harmful explosion.
If the odor of LP gas (e.g., rotten eggs) is ever detected, immediately discontinue use of any gas appliances and
seek the services of a qualified service technician.
Recommended Precautionary Practices
The following practices are recommended to assure continued safety and reliability of the LP gas system; these
are, of course, representative; not necessarily exhaustive. In all cases, use common good sense in the use of the
LP system.
•
Visually inspect the LP fill valve before any refueling operation to look for foreign materials or debris;
remove, as necessary, to assure a leak-tight connection.
•
Prior to any re-fueling operation of the LP gas system, shut off all the pilot lights.
•
NEVER, under any circumstances, check for LP gas leaks with any type of open flame; doing so would
probably cause an explosion and subsequent fire.
•
Periodically inspect visually the entire LP gas distribution system; do so at least semi-annually and
before any major trips. Should problems be noted, seek the services of a qualified service technician to
make necessary repairs and perform any maintenance.
2-8
D R I V I N G
&
S A F E T Y
I N S T R U C T I O N S
Warning
The LP gas distribution system in your motor home is designed for liquid propane (LP)
gas ONLY. DO NOT attempt to connect and use any natural-gas or butane-gas
systems with this LP gas system.
Fire Safety
As with any enclosed system containing the three required conditions for fire (i.e., combustible materials,
oxygen, ignition sources), there will exist the possibility of fire. Tiffin Motorhomes has taken every precaution
and design practice to minimize or negate this possibility, but the final determination rests with the owner and
user of the motor home. Accordingly, it is in the best interests of the owners, users, and their guests to be
aware of basic fire-safety practices and procedures and those particular features that Tiffin Motorhomes has
provided for fire safety.
Fire Extinguisher
The Zephyr is equipped with a fire extinguisher (located on the wall behind and to the right of the passenger’s
chair; see Figure 2-6) rated for both Class B (i.e., grease, gasoline, diesel fuel, flammable liquids) and Class C
(i.e., electrical) services—these are typically the most likely types of fires to be expected in motor homes. Read
and understand the accompanying owner’s manual on that extinguisher (found in your Owner’s Information
Package) and remember the location of the extinguisher. In an emergency, you won’t have
the time or presence of mind to do so then. You may wish to purchase other extinguisher(s)
[e.g., for the rear interior, around the generator outside; etc.] at your discretion.
These types of fire extinguishers are pressurized, mechanical devices and require that
appropriate care be used in their safe storage and use. The owner’s manual will provide
necessary guidance for the proper storage, handling, and use of the extinguishers. Prudent
preventive maintenance suggests monthly inspection of any fire extinguisher to assure that it
is sufficiently pressurized (i.e., the needle on the gauge is in the “normal” zone) and that the
Figure 2-6.
Fire
Extinguisher
mechanical components are not blocked in any way.
Do not test a fire extinguisher by partially discharging the unit—this will cause a loss of
pressure and may lodge some fire-retardant materials in the valve mechanism and cause the
extinguisher to continue to vent slowly down to zero pressure. Rather, if an extinguisher is ever partially used;
continue its use until the unit is completely discharged then have the fire extinguisher fully recharged at an
appropriate service center (one can call any fire department for information on having an extinguisher
recharged in that particular locality). DO NOT wait a long time to recharge an empty fire extinguisher; you’ll
never know when it may be needed.
Should a fire occur inside or around the motor home, evacuate the motor home quickly and calmly—do
not panic. In the event of heavy smoke or extensive flames, keep low (crawl if you must) and make your way to
2-9
D R I V I N G
&
S A F E T Y
I N S T R U C T I O N S
the nearest exit (door, emergency window) and leave. If the fire involves a fuel source (e.g., motor fuel, LP gas);
consider the probability of an explosion and move sufficiently far away to minimize personal harm.
If such is available, immediately place a call to the local fire department (or ask someone nearby to do so) to
report the fire. Consider the cause and the consequences of the fire and the risks associated with possibly
fighting the fire yourself before trying to extinguish it—DO NOT expose yourself or others to unnecessary
danger.
Smoke Detector
The Zephyr motor home is equipped with a battery-operated smoke detector (Figure 2-7) located on the ceiling
in the living area of the motor home (left-hand side of picture). Read
and become familiar with the operation and periodic testing of this
detector. The smoke detector should be tested on a weekly basis, before
each trip, and after any period of storage of the motor home. If a lowbattery condition is noted or the alarm “chirps” to indicate a low-battery
Figure 2-7. Smoke Detector (Left)
condition, immediately replace the battery.
It would be prudent to keep replacement batteries in the motor home for any in-transit replacements so that
the smoke-alarm capability is never compromised. DO NOT disable the smoke detector for any transient,
false alarm (e.g., cooking smoke, dusty furnace, tobacco smoke); rather, ventilate the motor home with fresh air
and the alarm will reset.
Emergency Exit Window
In the rear of the motor home, there is an emergency exit
window (Figure 2-8) in the bedroom—this window is
designed for an emergency exit when it is not practical to
exit by the door [also an emergency exit] in the front of the
motor home. This window is readily noticeable by its red
handle and the red “EXIT” label on that window.
To use this window as an emergency exit, lift the handle
and push outward on the window. As required, the
Figure 2-8. Emergency Exit Window
window can be closed by pulling the window inwards and
then lowering the handle to latch the window back in place. When the motor home is to be parked, it would be
wise to note where this window will be so that this exit won’t be blocked (e.g., against a tree, pole, or wall).
Parking Procedures
To park the motor home in any unfamiliar terrain, examine the prospective site for surface irregularities, slopes
or inclines, and other discontinuities (i.e., stumps, rocks, external connections for power/water/sewage) and
also examine the area immediately above the proposed parking site for obstructions (e.g., tree branches and
2-10
D R I V I N G
&
S A F E T Y
I N S T R U C T I O N S
limbs, signs, overhead wiring). If the motor home is to be backed into the proposed parking site, strive to have
that site be on the driver’s left-hand side, as this will allow the driver to watch the rear of the motor home.
Back up slowly and use the side mirrors and the back-up camera as a guide or, better yet, have another person
outside provide supplemental guidance to help park the motor home.
When the motor home is finally situated, shift the transmission into neutral, set the air brakes, and then turn
“off” the engine. Activate the leveling-jack system (see Chapter 9 for more detail) to level and stabilize the
motor home.
If the motor home is to be powered externally, connect the 120 VAC power to the motor home. Turn “on”
the LP gas valve at the LP tank. Connect the fresh-water supply and sanitize the water systems (see Chapter
11), as needed. Connect the waste drain hose to the external sewer hook-up. Start the refrigerator, water
heater, and furnace; as warranted. Light the oven pilot light, as needed. Certain appliances, such as the
refrigerator, will not work properly if the motor home is not level, so be sure to complete the motor homeleveling process before activating any of the appliances.
Towing Hitch
The Zephyr is fully capable of towing typical motor vehicles; the motor home is equipped with a Class 3,
10,000-pound towing hitch (Figure 2-9) and associated wiring
connector. The motor home is capable of towing light loads and
instructions for such are found in the chassis-manufacturer’s literature
in the Owner’s Information Package provided with the Zephyr.
As a towed vehicle being pulled by a motor home represents a greater
complexity in driving for the driver (e.g., turning, backing, parking),
one should not attempt such on the road without first practicing such
Figure 2-9. Class 3 Towing Hitch
(e.g., in a vacant lot) to master these skills.
The total weight of the motor home and any vehicle towed by that motor home must not exceed the Gross
Combined Weight Rating (GCWR). When the motor home is being weighed, remember to account for
passengers and their locations in the motor home. Any vehicles to be towed by the motor home should
have adequate active braking.
The wiring connector provided is a standard seven-pin connector, a more detailed description of which is
provided in Chapter 7. If needed, the connector for the mailer brake actuator is located beneath the access
panel located on the dashboard pod.
2-11
H E A T I N G
&
A I R
C O N D I T I O N I N G
Chapter
3
Heating & Air Conditioning
3-1
H E A T I N G
&
A I R
C O N D I T I O N I N G
Furnace
Warning
Never attempt to modify the furnace. To do so may cause fire, explosion, carbonmonoxide poisoning, and/or asphyxiation. If the furnace is malfunctioning,
immediately shut the unit “off” and call a trained service technician to make necessary
repairs as soon as possible.
The Zephyr motor home is equipped with a forced-air furnace fueled by LP gas. The furnace is
controlled by the wall-mounted thermostat (Figure 3-1) located inside the motor home—this thermostat
controls both the heating and air conditioning for the motor home.
In the heating mode, the furnace heats air which, in turn, is circulated through ductwork in the floor of
the motor home. If any obstruction(s) block the floor vent(s) or air-return register, then the furnace will
not function properly. Therefore, any items stored under the cabinets should be
carefully stowed to prevent damaging or crushing the furnace ducting or blocking
the warm-air return.
When a furnace is being used for the first time, there may be an initial “burn-off”
of manufacturing compounds or residues left on the heat exchanger or in the
ductwork which could produce odors, fumes, and possibly some smoke. This
occurrence is normal and should not cause concern, unless it persists for an
excessive amount of time.
To minimize the after-effects of this “burn-off” process, the initial use of the
furnace should be done with all the doors and windows open to permit normal air
circulation to dissipate these possible odors and fumes.
Figure 3-1. Thermostat
For routine operation of the furnace, set the thermostat to the desired temperature setting and then turn
“on” the thermostat; in about a minute, the furnace should begin to operate and warm or hot air should
be coming through the ductwork.
To shut down the furnace, turn the thermostat to the “off” position. Even though the thermostat may
be turned “off,” the furnace system will continue to run for about a minute or so to permit a gradual
cool-down of the heating system which is normal.
On a regular basis, thoroughly clean the complete furnace and air-tube passageways to remove dust, lint,
and any other possible obstructions. Leak-test the entire LP gas system at least semi-annually. Also
check and clean the air-blower system annually.
3-2
H E A T I N G
&
A I R
C O N D I T I O N I N G
Any access hatches to the furnace are for authorized service personnel only, as there are no userserviceable parts on the furnace. Accordingly, do not attempt to tamper with the interior of the furnace.
Warning
Be cautious when washing the exterior of the motor home; water should never be
sprayed directly into the furnace vent. Should any water be forced beyond the rain
baffles into the furnace vent, the furnace may rust which, in turn, may cause improper
combustion and produce unwanted by-products of combustion.
Before the beginning of each travel season, the furnace should be thoroughly cleaned and inspected. Any
obstructions, debris, or lint which may obstruct free air flow or impede the operation of the aircirculation system should be removed. For example, accumulated dust or lint could possibly obstruct the
orifices for the pilot light or may accumulate on the blower blades and unbalance the operation of the
blower. Additionally, any debris in the ductwork, when heated by the furnace, could emit unpleasant
odors or possibly become a fire hazard.
Consequently, the furnace system (including ductwork) should be periodically cleaned; annually is
recommended unless the motor home is subjected to dust levels significantly greater than average; in
which case more frequent cleaning is recommended. The Owner’s Information Package provides
recommended cleaning tips and procedures; when needed, a more thorough cleaning should be
performed by a qualified service technician.
Air Conditioning System
The factory-installed air-conditioning system is designed for 120 VAC power supplied either from the
external power hookup cord or from the generator. Any unnecessary interior heat loading (e.g., exposure
to direct sunlight for long periods of time; transmittance of sunlight through the windows) will work the
air conditioning system harder and may compromise the desired results. Accordingly, if the air
conditioning system is to be used, park the motor home in a shady location whenever possible and close
drapes on those windows exposed to direct sunlight. Additionally, any heat-producing sources (e.g.,
oven, unnecessary lights) within the motor home will work against the air conditioning system; so strive
to minimize their use.
The air conditioning system is the major consumption device of electrical power in the motor home.
When this system is being used in an RV park, cumulative use of these air-conditioning systems by the
resident motor homes can create, at times, a bigger demand for electrical power than is actually available.
Accordingly, at such times a “brown-out” condition may arise—this is when the AC voltage normally
available drops to a lesser value (e.g., 10-20% below normal or more).
“Brown-out” conditions cause appliances to draw greater currents to make up for the reduced voltage;
thereby causing circuit breakers to trip or fuses to blow. Under such conditions, your own motor home
3-3
H E A T I N G
&
A I R
C O N D I T I O N I N G
is not at fault; simply reset your breakers and/or replace your fuses. Should such conditions continue,
one may wish to turn reduce the electrical load (in this case, turn “off” the air conditioning system for
awhile) or start the electrical generator.
To cool the motor home, the thermostat inside the Zephyr is used—this is
the same thermostat which controls the furnace functions (described earlier).
The air-conditioned, cooled air is emitted through the vents which are
located in the roof throughout the entire coach. The discharge and return air
vents run parallel, front to back, on the ceiling. Note that the return vents are
similar to the air conditioning vents. This system allows even distribution for
the returns instead of forcing an excess amount of return air through two
smaller openings. The even return system takes more of the hot air from the
Figure 3-2. Round
motor home, thereby providing cooler air throughout the unit. The air
Vent/Filter
conditioning vents that are mounted on the ceiling are round vent filters
(Figure 3-2) that need to be periodically checked for dust accumulation. When dust has accumulated on
the filters, remove them and wash in a mild detergent and warm water.
Thermostatic Controls
The following is a brief overview of how best to use the thermostat (Figure 3-3).
For more detailed instructions, please consult the thermostat literature in the
Owner’s Information Package.
1. Turn “on” the power switch on the thermostat(s).
2. Press the Mode button to select the desired function (e.g., COOL,
FURNACE, FAN ONLY, etc.). Note: In the “COOL” mode there will
be a delay of several minutes before the refrigerant in the air-conditioning
system begins to cool the motor home, as the compressor is on a timedelay circuit and it must also cool the ductwork to the vents first.
Figure 3-3. Thermostat
3. Press the Fan button to select fan speed desired or automatic operation.
4. Press the Up and/or the Down buttons to set the desired temperature for the motor home.
5. If your vehicle should contain more than one control zone, press the zone button to select the
desired zone and then repeat the procedures from Step 2 onwards for each control zone.
NOTE: If the Comfort Control is turned “off” or the thermostat loses power (i.e., power failure), the
air-conditioning system will resume operation at the last settings programmed into it when electrical
power is restored.
Liquid Propane (LP) Tank
The Zephyr is equipped with an ASME (American Society
of Mechanical Engineers)-approved LP tank (Figure 3-4)
which is equipped with an automatic pressure regulator.
This tank contains liquid propane fuel under high pressure.
As this fuel passes through the main valve and through the
regulator, it is converted into a gas and its pressure is
reduced to a safe level for use within the motor home. A LP
Figure 3-4. Liquid Propane Tank
3-4
H E A T I N G
&
A I R
C O N D I T I O N I N G
gas-distribution system distributes the gas to those appliances using such in the motor home. The
“heart” of this LP gas distribution system is the regulator and that regulator should only be adjusted by a
qualified service technician. Most of the problems encountered in lighting the pilots of these appliances
are caused by regulator mis-adjustments.
The major component of the LP gas supply is a manifold pipe which runs lengthwise underneath the
motor home floor. From this manifold, the various gas appliances are connected by copper tubing with
flared fittings so that connections and disconnections can readily be made, as needed.
Should any of the secondary tubing develop a leak, either on the tubing proper or at the fittings, do not
attempt to splice any of these lines. Instead, have a qualified service technician run a new length of
tubing to the appliance of concern and then have that line leak-tested before placing it in normal
operation.
To remove, repair, or replace any gas-operated appliance; always close the main gas valve at the LP
tank—this measure will provide an additional element of safety to prevent gas leakage and possible,
subsequent explosion hazards. However, if a gas leak is noted or suspected, turn “off” the main valve
and keep the LP gas system “off” until that system is inspected by a qualified service technician as soon
as possible.
Do not delay in addressing any possible gas leaks with appropriate service because of the inherent hazards
to safety.
Warning
When the motor home is not being used, the main LP gas valve must be turned “off.”
Also, turn “off” the main valve when the LP gas tank is to be refueled to avoid the
possibility of ignition fuel fumes by the pilot lights. All gas valves on the gas-operated
appliances with Direct Spark Ignition (DSI) should also be in the “off” position during
refueling and/or maintenance operations. DO NOT store LP, motor fuel, propane,
butane, or other flammable liquids inside the motor home as these represent a very
real fire hazard and possible threat to life.
LP Tank Filling Practices
Any LP gas tank associated with the motor home should never be filled to more than 80% of total
capacity; filling should always be done only when the motor home is leveled. If the motor home is not
level, the tank may be overfilled (i.e., more than 80% of capacity) and, thus, subject the motor home to
possible fire or explosion from resultant uncontrolled gas flows.
3-5
H E A T I N G
&
A I R
C O N D I T I O N I N G
LP Gas Regulator
As noted earlier, the LP gas regulator (Figure 3-5) is the “heart” of the LP gas distribution system. This
regulator reduces and controls the pressure of the gas on the outlet end to provide a constant supply of
gas at a constant pressure to the gas-operated appliances.
The regulator has a vent to relieve excess pressure on the inlet side
of the regulator, should excess pressure develop in the gas tank and
connecting gas line to that regulator inlet. The vent would normally
release the excess LP gas to the atmosphere until the overpressurization condition is eliminated.
This vent should be regularly checked to assure that it is not clogged
Figure 3-5. LP Gas Regulator
or obstructed. If that vent is blocked from normal operation,
component or system failures may result. If periodic visual inspection indicates any sign of corrosion or
degradation, contact a qualified service technician to repair the regulator as soon as possible; DO NOT
operate the LP gas system with any faulty component in place.
Occasionally, the inherent moisture in the LP gas can cause a freeze-up of the regulator when the gas
passes through the regulator. The regulator reduces the high pressure of the gas on its inlet side to a
reduced pressure on its outlet side by permitting a controlled expansion of the gas through the
regulator—this gas expansion necessarily cools the gas (by means of the Joule-Thompson effect) and, if
cooled enough, may cause any moisture content to freeze.
To minimize or negate this possibility, always keep the main valve to the LP gas tank closed when the
system is not in use. When the LP tank is empty, keep the main valve closed until re-filling is to be
performed—this process will keep any moisture-laden air from back-flowing into the gas system and
trapping unwanted moisture in the LP gas tank. If an empty LP gas tank has been exposed to the
atmosphere for an extended time, let a qualified service technician purge the tank before its next filling
operation.
Important
When a LP gas regulator is installed or re-installed, the regulator must always be
installed with the gas diaphragm vent facing downwards. For more information,
consult the manufacturer’s literature in your Owner’s Information Package that came
with the motor home.
3-6
H E A T I N G
&
A I R
C O N D I T I O N I N G
Carbon Monoxide/LP Gas Detector
Warning
Liquid propane (LP) is extremely flammable and, when contained, explosive when
mixed with air. Consequently, never check for leaks in LP gas lines or appliances with
an open flame or sparking devices. Do not use any ammoniated or chlorinated
household-type detergents for “bubble testing” possible leak sites—these detergents
may generate fissures or cracks on the metal tubing (e.g., copper) and flared fittings
(e.g., brass). Have your LP gas system leaks repaired ONLY by a qualified service
technician; do not attempt these yourself. Keep the main valve to the LP gas tank
closed and all appliances turned “off” when the motor home is stored. If any of the
valves do not close “leak-tight” by hand, have those valves examined and repaired by a
qualified service technician. DO NOT, under any circumstances, attempt to use a faulty
LP gas system and/or appliances as such may represent a safety hazard.
Since LP (i.e., liquid propane) gas is more dense than air, the LP gas will naturally settle to the lowest
point in an enclosed space—in the motor home, this would be the floor.
Because of this fact, the CO/LP gas detector (Figure 3-6) is necessarily
mounted close to the floor. To activate the CO/LP-gas sensor on this
detector for the first time, remove the sensor activation strip, if such was not
performed during the pre-delivery inspection.
If the alarm persists in re-arming and giving further alarms; ventilate the motor Figure 3-6. CO/LP Gas Detector
home (by opening doors and windows) and then check for possible LP gas leaks.
If the leak cannot be readily found, then close the main valve to the LP tank and turn “off” all gas appliances
and then take the motor home to a qualified service technician after the ventilation process is concluded and
the doors and windows again shut.
3-7
M A J O R
A P P L I A N C E S
&
A C C E S S S O R I E S
Chapter
4
Major Appliances & Accessories
4-1
M A J O R
A P P L I A N C E S
&
A C C E S S O R I E S
Refrigerator
The Zephyr will be equipped with a residential refrigerator (Figure 4-1). Please note that the residential
refrigerator will only operate on 110V. Any time that the motor home is not
connected to shore power, the refrigerator will have to be operated by use of the
inverter.
The refrigerator has its own water filters for the ice maker. NOTE: These water
filters have to be removed before winterizing your motor home.
For further instructions on how to properly operate and maintain the residential
refrigerator, refer to the specific owner’s manual located in the Owner’s
Information Package.
Note: The inverter must be “on” for the residential electric refrigerator to
operate if not connected to shore power!
Figure 4-1.
Residential Refrigerator
Microwave / Convection Range
The Zephyr contains a microwave/convection range (Figure 4-2). All microwave ranges operate on 120volt AC electrical power, supplied either by the external
electrical hookup or by the onboard electrical generator in
the motor home. Between the power source(s) and the
microwave range is a surge protector to protect the unit
from electrical transients and power surges.
Figure 4-2. Microwave / Convection Range
Touch-pad controls on the microwave range are used for
operating the range (i.e., cooking temperature, mode, power
level, and cooking time). For basic operating instructions on
the proper use of the microwave/convection range, please
consult the specific manual in the Owner’s Information
Package.
Air-Filtration Fan
In the Zephyr, the “exhaust” or air-filtration fan is built into the microwave and its function is to filter
the air only; it does not exhaust to the outside. This range hood is equipped with a multi-speed fan and a
light for convenient use. The hood should be used whenever any cooking is performed to filter any
airborne cooking residues and heated air.
Additionally, the range hood can be used as supplemental filtration of other odors and gases including
tobacco smoke, candle fumes, and related vapors. The range hood contains filters which can be removed
and cleaned or replaced to assure sustained normal operation. Consult the particular owner’s manual
contained in the Owner’s Information Package.
4-2
M A J O R
A P P L I A N C E S
&
A C C E S S O R I E S
Cook Top and (Optional) Oven
The Zephyr is equipped with a two-burner recessed cook top as shown in Figure 4-3 (or, as an option, a
three-burner cook top and oven as shown in Figure 44. The optional oven has a piezoelectric ignition
source, rather than a pilot light, to start the oven).
To light the burners, push down on and turn the gascontrol knob counterclockwise to the “Ignite”
position. Continue holding down the knob fully until
the spark ignites the gas; then continue holding the
knob down for an additional 5-10 seconds (this
additional time is required for the thermocouple to be
Figure 4-3. Two-Burner Recessed Cook Top
heated sufficiently to activate the safety mechanism—
the thermocouple will automatically cut “off” the gas
flow if the burner goes “out”). Then release the knob and rotate it to the desired setting. To turn the
burner flame “off,” turn the knob clockwise to the “off” position.
If the burner does not start after a few attempts, discontinue the process, let the released gas dissipate,
then try the process again. The burner knobs operate in a counterclockwise (CCW) manner and must be gently pushed inwards as they
are being turned.
If the optional oven doesn’t have a piezoelectric ignition source, light
the oven by pushing inward on the oven control knob and rotating it
CCW to the “pilot on” position, then light the oven pilot light
located at the back left-hand side of the oven burner—this may take
a few seconds until the air in that line is purged and replaced with the
LP gas.
Do not attempt to adjust the oven pilot light as it has been factoryadjusted and factory-set.
Figure 4-4. Oven (Optional)
To extinguish the oven pilot light when use of the oven is concluded, push inwards on the oven control
knob and turn that knob clockwise (CW) to the “off” position.
The Zephyr is equipped with a two-burner cook top having a countertop cover matching the same décor
as the counters in the motor home. This cover both provides protection to the burners when they are
not in use and additional counter space, as needed.
Before any cooking on the cook top is attempted, the cover must be removed from the cook top and
stowed so that the cooking surface is free and unobstructed. Do not replace the cover immediately after
using the cook top; wait until those surfaces are cool to the touch before replacing the cover. Never use
the cook top range when the motor home is in motion.
As a safety feature, the following label will be noted in the cooking area:
4-3
M A J O R
A P P L I A N C E S
&
A C C E S S O R I E S
Warning
DO NOT USE cooking appliances as a heating source for the motor home. Cooking
appliances require fresh air for safe operation. Before using any cooking appliance,
make sure that an overhead vent or window is open and/or turn “on” an exhaust fan.
Remember that any LP gas-operated appliance in the motor home will be consuming oxygen in the motor
home. If the motor home is totally closed during such operation, the oxygen level may be reduced (and the
associated carbon monoxide level may be increased) thereby causing possible harm or death to the occupants
through asphyxiation. Always use these appliances with proper ventilation.
DANGER – Notice -- DANGER
IF YOU SMELL GAS, YOU SHOULD IMMEDIATELY:
Extinguish any open flames, pilot lights, and all smoking materials. Do not touch or
operate any electrical appliances or switches. Immediately shut “off” the gas supply at
the main tank valve or supply connection. Open doors, windows, and other ventilation
openings (then immediately leave the motor home!) to allow entrapped LP gas to
dissipate. Have the LP gas system checked to locate and fix the source(s) of the
leakage.
TELEVISION SYSTEM OPERATION
Television Antenna
The Zephyr motor home is equipped with a retractable antenna (Figure 4-5) for
television (TV) reception of all VHF (i.e., channels 2-13) and UHF (i.e., channels 14
upwards) channels. To deploy the antenna for proper reception of TV signals, turn
the TV-antenna crank clockwise (CW) to raise the antenna; this should take about
10-15 turns until some resistance is noted.
Once the antenna has been raised, slowly rotate the antenna to receive the best
picture on the channel of choice—this rotation is accomplished by pulling down on
the directional handle with both hands until it disengages from the ceiling plate and
then rotating the antenna until optimal reception is realized.
Figure 4-5. TV Antenna
4-4
M A J O R
A P P L I A N C E S
&
A C C E S S O R I E S
There is an antenna power-booster switch (left-hand side of the audio-video control console) which, when
pushed, strengthens the signals to be received.
If your location is within a metropolitan area, you may need to rotate the antenna for each different station
desired to aim the antenna towards each particular station.
If the location of the motor home is remote from any metropolitan area; the antenna, once positioned for a
particular station, should be adequate for all other stations capable of being received from that particular area.
Some experimentation may be required to determine the “best” setting for each location of the motor home
and the stations desired to be viewed.
If the motor home is moved or re-oriented after the TV antenna positioning had been completed; it may be
necessary to re-adjust the position of the TV antenna to re-aim that antenna back towards the desired source(s)
of TV signals. Particularly since reception of UHV TV channels (i.e., channels 13 upwards) is essentially lineof-sight; any obstruction (e.g., tree, building, tower) between the antenna and the signal source will compromise
the signal reception; so be careful in positioning the motor home.
Prior to moving the motor home, the TV antenna must be retracted. To lower the antenna, rotate the
directional handle until the pointer on that handle is aligned with the pointer on the ceiling plate; then turn the
elevating crank counter-clockwise (CCW) about 10-15 turns (until some resistance is noted) to lower the
antenna and lock it into its retracted position for travel.
DO NOT partially lower the antenna; it must be either fully deployed (raised) or retracted (lowered)—any
intermediate position will lead to damage to the antenna itself or to the motor home.
When the TV antenna is raised and adjusted, if the TV reception is weak, blurred, or of inferior quality; examine
the connections from the TV to the antenna and make sure that the power-boost switch is actually “on.” If the
symptoms persist, then consult your authorized service dealer.
Television Sets
The television sets (Figure 4-6) furnished with the motor home are cable-ready; one is in the overhead bay
above the dash and the other is in the bedroom, depending on the
particular floor plan of the Zephyr purchased.
The televisions are powered by 120-volt AC electricity; therefore, the
motor home must either be plugged into an external source of AC
power or using on-board power from the generator. An optional
inverter would also permit the 12-volt DC power to be converted into
120-volt AC for the television(s).
Figure 4-6. Television Set
Detailed operation of the television(s) is provided in the
accompanying owners manuals found in the Owner’s Information
Package included with the motor home.
4-5
M A J O R
A P P L I A N C E S
&
A C C E S S O R I E S
Generic operations of the television would include a basic “on/off” switch, volume “up/down” control,
channel “up/down” selector, and menu “up/down” selector—these functions are found both on the television
set itself and on the accompanying remote that comes with the television set.
If the motor home has been wired for satellite TV, there should be an interior jack or jacks and an exterior jack
to connect the satellite system. Consult your owner’s manual for the satellite system to determine the correct
connections to be made.
Infrared Repeater
The Zephyr will feature an infrared repeater (Figure 4-7) which enables the owner to utilize the remote control
from various areas of the coach. An infrared repeater will be located in the bedroom and by the overhead TV
located in the driver’s area. If your Zephyr has the
optional outside entertainment system, this feature
will be located on it also.
To utilize the infrared repeater, locate the stem
(Figure 4-8) inside the cabinet that contains the
DVD player. Peel the adhesive backing from the
back of the stem and line it against the DVD’s
Figure 4-7. Infrared Repeater
Figure 4-8. Stem inside cabinet
infrared eye in order for the infrared repeater to
operate when the remote control is directed toward the infrared repeater situated by the overhead TV. This will
allow you to change channels when the remote is directed toward the TV.
Audio-Video Control Console
The Zephyr contains an audio-video control console (AVCC) (Figure 4-9) to enable one to select where the TV
signal is routed (i.e., front and/or rear
televisions) and also an auxiliary (“AUX”)
source.
The TV antenna booster is located on the
left side of this console. To make the desired
selection, simply press the appropriate
button(s) to select what is to be viewed and where. The front television is selected by pushing button “TV 1”
and the rear television (and outside television, as warranted) is selected via button “TV 2.”
Figure 4-9. Audio-Video Control Console
One can view a different channel or input source on each of the television systems. For instance, if one should
select the “ANT” option for the front television, any channels available on the antenna system can be viewed
on the front television. At the same time, if one selects “VCR” for the rear television, the chosen medium can
be viewed on the rear television. The “AUX” position permits connection to an external cable system, satellite
dish, video games, or DVD player.
4-6
M A J O R
A P P L I A N C E S
&
A C C E S S O R I E S
AM / FM / CD Stereo System
Your motor home will be equipped with an AM-FM stereo system (Figure 4-10). This system is powered by the
12-volt DC system of the motor home and operates like any conventional carstereo system (see Owner’s Manual for specific instructions). It is important that
you read the information provided with the system.
A driver’s steering wheel remote and passenger’s card remote are included for
operation of the radio. They are located in the owner’s information package.
NOTE: Your radio has Sirius satellite radio capabilities but this does not
Figure 4-10. AM / FM / CD Stereo
System
mean it is ready for immediate use. As an option, your radio may be equipped
with a preinstalled tuner that will allow you to receive satellite radio after
contacting Sirius and purchasing a subscription. Activation of
the tuner requires the Sirius identification control number
located on the back of the Sirius Satellite Radio Tuner Box. If
your motor home is equipped with the optional tuner box, you
will find a green bar code label with the identification number
(Figure 4-11) in the owner’s information package. Your motor home has
Figure 4-11. Sirius Satellite
a factory installed satellite antenna (standard) but it may not have the
Identification Label
optional tuner box. If you wish to purchase the subscription but do not
have the tuner box, you may purchase the tuner box from Sirius. All necessary cabling and antennas are
preinstalled. If you have any questions concerning the Sirius satellite option, you may contact Sirius Customer
Care direct at 1-888-539-7474.
To turn the AM/FM/CD stereo system on and off, push the “POWER” button.
To select a Play Source such as the radio, CD or optional equipment such as the Sirius Satellite Radio, external
CD changer, or auxiliary sources, push the “Mode” button to choose the desired play source.
Sound Settings:
Volume: Rotate the VOLUME knob left or right.
Bass, Treble, Balance or Fader: Push the VOLUME knob to scan between the different sound controls. Once
the desired function is in the display area rotate the knob left or right to achieve the desire level.
Equalizer: Push the EQ button to choose between preset equalizer settings: Classic, Rock, DSP Off (digital
sound processor off), Flat, Pop and Jazz, as indicated in the display area.
Mute: Push the MUTE button to mute the volume level. Press again to return to previous volume level.
Loudness: Push the LOUD button to boost high and low tones at low volume levels.
4-7
M A J O R
A P P L I A N C E S
&
A C C E S S O R I E S
Sirius Satellite Radio (optional):
Note: If your RV has an optional Sirius tuner, it can be activated by calling 1-888-539-747487 (SIRIUS). The
Sirius Tuner ID Number (ESN) is required during the activation process. Follow the instructions below to
access the Sirius Tuner ID Number (ESN):
Push the MODE button until “SIRIUS” appears in the display area.
Push the TUNE button until “DIRECT” appears in the display area. Wait a few seconds and “CH 000” will
then appear in the display.
Push the BAND button and the first 4 digits of the 12 digit Sirius Tuner ID Number (ESN) will be displayed.
Push the DISP button and the last 8 digits of your 12 digit Sirius Tuner ID Number (ESN) will be displayed.
Push the TUNE button to exit.
Selecting Sirius: Push the MODE button until “SIRIUS” appears in the display. Please be patient as it may take
a minute to receive a satellite signal.
Manual Tuning:
Push the TUNE button until “NORMAL” appears in the display.
Rotate the TUNE knob to select a station from 01-182.
Category Tuning:
Push the TUNE button until “CATEGORY” appears in the display.
Push button 1 or 2 to find the desired category.
Rotate the TUNE knob and select a station.
Direct Tuning:
Push the TUNE knob until “DIRECT” appears in the display.
Rotate the TUNE knob and select the first digit (0 or 1).
Push the TUNE knob again.
Rotate the TUNE knob and select the second digit (1-8).
Push the TUNE knob again.
Rotate the TUNE knob and select the third digit (1-9). The tuner will start playing the station you have selected
when the third digit stops flashing.
Note: Satellite radio signal may be blocked by trees, buildings, bridges, or tunnels.
4-8
M A J O R
A P P L I A N C E S
&
A C C E S S O R I E S
To operate the AM/FM/Weather Band, push BAND button to select F1, F2, F3, AM1, AM2, or W (weather
band).
Manual Tuning:
Rotate the TUNE knob left or right and hold until “MANUAL” appears in the display then release knob.
Rotate the TUNE knob again left or right until the desired radio station appears in the display.
Scan Tuning:
Push the TUNE knob to scan every 5 seconds for a different radio station. To stop scanning push the TUNE
knob again.
Seek Tuning:
Rotate the TUNE knob left or right then release to seek for a different radio station.
Weather Band: Push the W-BND button for instant weather band operation.
NOTE: Push the MODE button to return to playback of other sources.
Programming AM/FM Stations: Select a radio station then select a button 1, 2, 3, 4, or 5 and push and hold
until it beeps. The radio station is now programmed to that button.
Recalling Programmed Radio Stations: Push button 1, 2, 3, 4, or 5 to recall a pre-programmed station.
Clock Settings
Display Button: Push and hold the DISP button until the clock is flashing in the display.
Adjusting the Minutes: Rotate the TUNE knob to the Left to adjust the Minutes.
Adjusting the Hours: Rotate the TUNE knob to the Right to adjust the Hours. Note the AM/PM indicator.
NOTE: When correct time displays wait a few seconds to allow the time to program.
CD Operation:
Playing a CD: Insert a CD (label side up) into the CD slot. The CD will auto-load and start playing. NOTE: If a
CD does not auto-load, DO NOT FORCE into the slot, as you may already have a CD loaded.
CD Track Selection: Rotate the TUNE knob left or right to change the track.
Ejecting a CD: Push the EJECT button to eject a disc.
Pausing a CD: Push the MUTE button to “Pause” disc, press again to resume play.
4-9
M A J O R
A P P L I A N C E S
&
A C C E S S O R I E S
CD Changer (optional):
Load CDs: Insert the CD magazine into the external CD changer.
Selecting the External CD Changer: Push the MODE button until “CDC” appears in the display.
CD Selection: Push button 1 or 2 to scroll through the selection of CDs in the CD changer. If a CD is not in
one
of
the
trays,
the
unit
will
continue
until
the
next
CD
is
found.
CD Track Selection: Rotate the TUNE knob left or right to change the track.
Reset Button:
The radio panel or LCD display may fail to function normally due to the vehicle’s battery condition, and may
require resetting the microprocessor if:
The vehicle has been “jump started” from a dead battery condition.
The vehicle battery becomes very low and is quick-charged.
The vehicle battery is removed and replaced.
Should this condition occur, simply press and release the RESET button on the radio panel using the tip of a
ball point pen. All station programming should remain, but you will have to reset the clock.
Home Theater System
The motor home has a contemporary, home theater system (Figure 4-12) which offers true surround sound for
the front television and also when DVD
programs are viewed featuring the Dolby
Surround Sound system. This system,
though, does not permit playing through
the rear entertainment system in the
bedroom. As this home theater system
offers many types of entertainment
options, it is worthwhile to read the manual thoroughly before attempting extensive use of this system. This
system will also play CDs and MP3 disks, among other media.
Figure 4-12. Home Entertainment Theater System
Cable & Telephone Jack
The Zephyr contains an exterior cable jack and also a telephone hookup (Figure
4-13). This telephone connection permits the owner to access external telephone
services (e.g., RV parks) so that these services are available for use within the
motor home proper.
Within the motor home there are several telephone jacks (e.g., bedroom, living
Figure 4-13. Telephone Jack
4-10
M A J O R
A P P L I A N C E S
&
A C C E S S O R I E S
room) for connecting telephone(s), as desired.
Dishwasher (Optional)
The Zephyr may be equipped with an optional compact dishwasher (Figure 4-14). If such is installed, the
following operating instructions may be used to operate that
dishwasher:
1. Load the dishes (be sure to remove all food scraps and
other materials such as paper napkins or towels).
2. Add desired detergent and rinse-aid solution.
3. Press the “power” button to turn the dishwasher “on”
(pushing this button again will then also turn the
dishwasher “off.”). Note: Merely opening the
dishwasher will automatically turn “on” the
Figure 4-14. Dishwasher (Optional)
dishwasher for a 30-second period. To end a wash
cycle before it’s fully completed, press the “power” button; at which time the dishwasher will pump any
remaining water in the dishwasher out of the unit.
4. Select Wash Program. By pressing the “program” button, the desired wash cycle can be selected. The
dishwasher will remember the last selection made, until a newer one is selected.
5. Check to assure that the drain filter is flush with the filter plate and the spray arm can rotate within the
dishwasher freely without impacting anything.
6. Start the dishwasher by closing the dishwasher door; then press the “start/pause” button to begin the
washing cycle. This button also has a “delay start” function, as desired.
7. Pause the dishwashing cycle, if desired, by pressing the “start/pause” button; wait for three beeps to be
heard, then one can safely open the dishwasher. Restart the dishwasher (after closing the door) by
pressing the “start/pause” button. Note: Forcing open the dishwasher door in mid-cycle may cause
damage and/or injury.
8. Finish the dishwashing cycle by noting when the dishwasher beeps six times to indicate the end of the
wash cycle. At the end of the washing cycle, the drying fan will continue to run for a pre-determined
time or until the door is opened. The drying fan assists in drying the washed contents and actually uses
very little electrical energy in the process. It is normal for some water to remain in the drain filter area
after the wash cycle is completed.
Note: Should a power failure occur when the dishwasher is operating, the dishwasher will stop. It may be
impossible to open the dishwasher, depending on where it was interrupted in the dishwashing cycle. When the
power is again re-applied, the dishwasher will resume its operation at the point where it was interrupted. When
not in actual use, the dishwasher can be used to store dishes, cups, glasses, and the like; as the dishwasher itself
provides secure storage of these items while in transit.
4-11
M A J O R
A P P L I A N C E S
&
A C C E S S O R I E S
Warning
The dishwasher must have 110 power or inverter power at all times to be locked during
transit. If not, the dishwasher could disengage during travel.
To ensure that the dishwasher is properly locked for travel, follow the steps below:
1. Push the center control, located on the face of the dishwasher, until it blinks green. Press down on the
key button to the right of the center button until it turns red and compresses. This denotes the
dishwasher is in “lock down” mode.
2. To decompress the dishwasher, simply push the key button for five (5) seconds and it will decompress.
Hydro-Hot Heating System
The Zephyr features a Hydro-Hot heating system (Figure 4-15) that provides a
continuous, on-demand supply of domestic hot water, as interior zone heating
where and when it is needed. Both heating features are accomplished by a unique
VDC-Powered Diesel-Fired Burner and a VAC-Powered Electric Heating
Element (120 VAC). These two heating sources maintain the temperature of the
Hydro-Hot’s solution of water and antifreeze. For detailed instructions on
operating the Hydro-Hot Heating system, refer to the specific owner’s manual
found in the Owner’s Information Package.
Figure 4-15. Hydro-Hot Heating
System
Caution
DO NOT operate the Diesel-Burner and/or the Electric Heating Element without the
water and antifreeze solution in the Hydro-Hot’s Boiler Tank. Failure to do so will cause
serious damage to the Heater.
4-12
M A J O R
A P P L I A N C E S
&
A C C E S S O R I E S
Warning
The Hydro-Hot’s Exhaust is HOT!
DO NOT park in areas where dry conditions exist underneath the vehicle, as a fire may
result (i.e. in a dry, grassy field).
DO NOT operate the Hydro-Hot’s Diesel-Fired Burner inside an enclosed building.
The Heater should be switched OFF when refueling.
CB Radio System Antenna Connection
The Zephyr comes equipped with an antenna and coaxial-cable connection (Figure
4-16) to enable the owner to install a Citizens Band (CB) radio of choice and
operate it conveniently from the Zephyr. The coaxial-cable connection for the
radio is found beneath the dashboard on the driver’s side. Accordingly, with an
owner-provided CB radio, that radio can be used to communicate with other
travelers on the road. To use the one’s CB system of choice, simply follow the
Figure 4-16. CB Antenna Installation
directions furnished with the CB radio. (Note: Channel 11 is considered an
emergency channel and monitoring this channel may give one information about road conditions, accidents,
and related matters potentially affecting the travels of the motor-home operator).
To talk with someone, simply press the “push-to-talk” switch and speak. To listen to any reply, release the
“push-to-talk” switch and listen to the speaker. Remember that communications are “one-way,” not “twoway” simultaneously—one must talk, and then allow some listening time for others to talk. Consequently, it’s
better to make brief transmissions and allow others to comment; rather than making prolonged speeches and
possibly not having anyone answer.
Observe the common courtesies (see the owner’s manual for more details) and acceptable speech. Several
states have their Highway Patrols monitor the CB frequencies (check for exact channels for each state of
interest) to learn about highway problems and emergencies. Be aware of these throughout one’s travels, in the
event that they may be needed.
Rear-View Camera Monitor System
The rear-view monitoring system (Figure 4-17) is provided to aid the driver in backing and parking the motor
home. A camera mounted on the rear of the vehicle feeds a televised view of the rear of the motor home to
the monitor located in the front near the driver.
4-13
M A J O R
A P P L I A N C E S
&
A C C E S S O R I E S
If the mode switch is in the “manual” mode, the monitor will be “on” when the ignition switch is turned “on.”
If the mode switch is in the “automatic” mode, the monitor will display
the picture from the rear-mounted camera only when the transmission
is in “reverse” gear.
To use this system effectively, please consult the owner’s manual for
this system; this manual is in the Owner’s Information Package.
Figure 4-17. Rear-View Monitoring System
Side-Mount Camera
As an enhanced aid to driving, the Zephyr motor home will feature side-mounted cameras (Figure 4-18) on
both sides of the motor home. These side-mounted cameras are activated
whenever the motor home in transit begins to make a turn.
When the “left” turn indicator is used, the left-side camera is activated and
that camera displays on the back-up monitor a rearward-oriented view of the
driver’s side showing that side of the motor home and a limited panorama of
what is alongside and immediately behind the motor home as it begins to
turn into that direction.
In this manner, the typical “blind spot” of most motor homes is drastically
reduced or eliminated so that the driver can make those turns with greater
confidence. Similarly, the “right” turn indicator operates in the same manner to show a rearward view of the
right side of the motor home when a right-hand turn is made.
Figure 4-18. Side-Mount Camera
Stacked Washer / Dryer
Your Zephyr will be equipped with a stacked washer/dryer (Figure 4-19).
Please note that it only operates when the generator is running OR on 50 amp service.
DO NOT attempt to operate the stacked washer/dryer on 30 amp service. For specific
information regarding the use of the stacked washer/dryer, consult the owner’s manuals
found in the Owner’s Information Package.
Note: The 1 ½” gray water valve must be fully open when operating the washer/dryer.
Figure 4-19. Stacked
Washer/Dryer
4-14
M A J O R
A P P L I A N C E S
&
A C C E S S O R I E S
Carbon Monoxide/ LP Gas Combination Detector
To protect the driver and other occupants of the motor home, the Zephyr is equipped with a carbon monoxide
/LP gas combination detector (Figure 4-20). This single compact system
provides a powerful combined alarm that detects both Carbon Monoxide
(CO) and explosive gases Propane (LPG) and Methane (Natural Gas). This
detector uses the latest microprocessor technology combined with two
electronic self-cleaning sensors that operate independently of each other. The
combined unit can detect both CO and explosive gases simultaneously.
Figure 4-20. Carbon
Monoxide/ LP Gas
Combination Detector
Carbon monoxide (CO) is a colorless, odorless, tasteless gas which, when
breathed, bonds to the hemoglobin in the red blood cells and, thus, drastically
reduces or blocks the transfer of oxygen from the lungs to the rest of the body. In
sufficient concentrations, CO kills by asphyxiation. In lesser amounts, CO makes
the victim groggy, lethargic, and unable to think clearly or quickly.
CO is one of the products of combustion for many materials including petroleum-based products (e.g.,
gasoline, diesel fuel, propane, butane; among others). Since many of the appliances and the engines associated
with the motor home produce CO in their normal operations, it is necessary to assure that CO levels do not
rise to dangerous levels within the motor home. In sufficiently high concentrations, CO can kill in minutes.
Consequently, the CO detector should be checked at regular intervals to assure it is in proper operating
condition and that its battery is fresh. Periodic checking with the “test” button to assure normal operation of
the CO detector and to allow the motor-home users to hear how the CO alarm actually sounds would be
worthwhile.
The most susceptible people to CO poisoning are unborn babies, small children, pregnant women, senior
citizens, and people with cardiovascular or respiratory problems. Consequently, it is prudent to check that CO
monitor regularly for normal operation and to remain aware of the symptoms of CO poisoning which include
dizziness, nausea, vomiting, muscular twitching, throbbing in the temples, incoherent thinking and speech,
weakness, sleepiness, and intense headaches.
Warning
Carbon monoxide gas—derived from products of combustion of motor fuel, LP gas,
and other petroleum-based products—is a deadly gas which can kill motor-home
occupants, if allowed to accumulate in sufficient concentration. Assure that all engine
operations are not restricted—tailpipes and exhaust ports should not be blocked or
restricted in any way. Additionally, any accumulation of exhaust gases outside or
underneath the motor home should be avoided as such may enter the motor home
through windows or vents—be careful how and where the motor home is parked to
avoid such conditions. Regularly monitor outside conditions to assure that all exhaust
4-15
M A J O R
A P P L I A N C E S
&
A C C E S S O R I E S
gases can readily be dissipated and not enter the motor home inadvertently.
=
Warning
Never sleep in a motor home when the engine is running—engine exhaust fumes could
enter the motor home and cause disability or death. Regularly check the exhaust
system to note any leakage sites and, if found, discontinue use of the motor home until
they are repaired by a competent, qualified service technician. Do not attempt repairs
on the exhaust system yourself and do not modify (temporarily or permanently) the
exhaust system at all.
Should any of these symptoms be experienced in the motor home, one should IMMEDIATELY evacuate the
motor home and seek medical help. Shut down the motor home and do not attempt to operate it again until
the source(s) of the CO are located and fixed.
In the event of an alarm, the following steps should be taken quickly:
1. If the alarm signal sounds (4 beeps and flashing or solid red light), operate the Test/Mute button.
2. Immediately move to a source of fresh air, either outdoors or by and open door or window. Do a
“head count” to make sure that all people (and pets!) within the motor home have moved to a source
of fresh air, too. Do not reenter the motor home or move away from the source(s) of fresh air until the
emergency responders have arrived, the motor-home interior is sufficiently aired out, and the alarm has
reverted to its normal monitoring function (i.e., no alarms).
3. Call the local emergency services (i.e., 911 in most locales) to summon help -- don’t go back into motor
home to make this call, but use a cell phone, if available, or have someone else nearby make this call.
4. Should the CO/LP Gas Detector Alarm again activate within a 24-hour period, repeat Steps 1 through
3 and also call a qualified service technician to investigate the possible sources of CO (e.g., fuel-burning
equipment and appliances) to locate, identify, and fix such.
Warning
Test the alarm’s operation after each storage period, before each trip or at least once
per week during use.
4-16
C A B I N E T S
&
F U R N I T U R E
Chapter
5
Cabinets & Furniture
5-1
C A B I N E T S
&
F U R N I T U R E
Cabinets
Your Zephyr contains cabinetry installed throughout the entire motor home from the driver’s area (Figure 5-1),
through the kitchen/dining areas, and back into the bedroom. The cabinetry
has been designed and built to provide ample storage space, to be easily
accessible, and to be conveniently located to support the areas of concern.
Construction of these cabinets incorporates various hardwoods, raised panels,
cabinet doors, and supports. Door pulls, handles, and knobs are installed in a
style complementing the particular décor of each Zephyr so that an
aesthetically-pleasing, as well as fully functional, storage capacity is realized.
For the many floor plans available in the Zephyr product line, cabinet design
has been optimized to provide maximal storage for each and every floor plan
Figure 5-1. Driver’s Console Cabinet
available. Accordingly, the Zephyr can readily accommodate the routine
materials, supplies, and customer-specific items desired for any travel
requirements. Further, these cabinets are designed to contain stored supplies quite securely during travel to
minimize or eliminate the possibility of shifting or spilling of cabinet contents during travel. Yet, when the
motor home is parked, all stored items are readily available in the cabinets for the convenience of the users.
As the storage requirements will vary somewhat from one floor plan to another, general observations can be
made about the Tiffin-supplied cabinetry which may or may not be applicable for your specific Zephyr
configuration.
Cabinets (Figure 5-2)
are provided in the
kitchen/dining area
to accommodate the
routine
cooking
utensils and groceries
normally desired for
travel. Storage space
within these cabinets
has been so designed
to accommodate the
typical sizes and
configurations
of
food supplies (e.g.,
cereal boxes, condiments, canned goods, bottled liquids) normally
Figure 5-2. Kitchen Cabinetry
taken on travel trips. Based on Tiffin Motorhomes’ extensive
experience with travel requirements of the seasoned motor-home users and from Tiffin Motorhomes’ own
research and development in cabinet-design requirements, the resultant cabinets offer the greatest storage
capacity possible.
Figure 5-3. Kitchen Countertop
In the bathroom and bedroom, additional cabinets are available for storage of sundries and toiletries specific to
these areas.
5-2
C A B I N E T S
&
F U R N I T U R E
In the kitchen, a color-coordinated countertop is provided on top of the floor-mounted cabinets. To maintain
the appearance of the countertop (Figure 5-3), clean with a damp cloth. If spotting occurs, clean the
countertop with a damp cloth and a mild liquid soap. Should some dried-on residue still persist, let a damp
cloth moistened with the liquid cleaner stand directly on top of that residue for 15-30 minutes to loosen the
residue, then clean that spot accordingly. Please note that strong chemicals, solvents, and cleaners (e.g., oven
cleaner) may damage the surface; so do not use any products not
specifically designed for countertop cleaning.
The countertop may be physically damaged, too, if proper care is not taken.
Do not cut anything (e.g., vegetables, fruits) directly on the countertop;
rather, use a cutting board on top of the countertop to provide necessary
protection to the countertop. Excessive heat may also damage the
countertop; therefore, any pots or pans taken directly from the range or
oven should not be placed directly on the countertop; rather, use trivets or
some other form of fireproof heat insulators to hold very hot pots or pans
on the countertop.
All drawers (Figure 5-4) are equipped with metal slides to provide
additional load-bearing strength for the drawers and to permit effortless
opening and closing of those drawers, even when they are fully loaded.
These metal guides have a slight “locking” action, when closed. To open
those drawers, slightly lift up on the drawer handle and then pull the drawer
open. To close, push the drawer closed until it “clicks” back into place (i.e.,
the locking action is engaged).
Figure 5-4. Kitchen Drawers
As this cabinetry is typically of furniture-grade quality, any commercial furniture polish or cleaner can be used.
Do not try to soak these wooden surfaces with any water or any other liquid; be sure to wipe up spills or
residues of any fluids that contact these surfaces to preclude any staining or discoloration of the cabinet
surfaces.
Furniture
Kitchen, Dining, & Living Room Areas
On all the various floor plans of the Zephyr, a built-in dinette booth
(Figure 5-5) is standard; a free-standing table (Figure 5-8) is optional. This
dinette provides additional storage under the seat area of the booth, in
addition to providing additional sleeping facilities (Figure 5-10). The
sleeping area is realized by lowering the dinette-table top and rearranging
the seating cushions. Specific directions for converting the booth dinette
into a bed are as follows:
Figure 5-5. Dinette Booth
1. Remove the seat cushions.
2. Remove the wooden fill blocks.
5-3
C A B I N E T S
&
F U R N I T U R E
3. Fold the table leg upwards, while slightly lifting the table, allow the table to swing down and rest
between the two booth seats; thus, forming the bed (Figure
5-6).
4. A filler strip (Figure 5-7) is attached to the seat portion (via a
long Velcro strip) of the sofa. Simply pull these two pieces
apart. The filler strip can be conveniently stored underneath
the dinette until you are ready to re-convert the bed back
into a sofa.
5. Reinstall the seat cushions and back rests to make up the
mattress for the bed.
Figure 5-6. Dinette Converted into Bed
The living room contains a standard sofa (Figure 5-9) which converts into a bed (Figure 5-10), as required. The
sofa is custom coordinated with the décor of the motor home. To convert the sofa into a bed, follow these
directions:
1. Remove all of the accent
pillows.
Figure 5-8. Dining Table and
Chairs
2. Under one of the seat
cushions locate the “black
tab” and slide the tab to the
left or the right and then
pull upwards on the seat
portion of the sofa—this
will cause the sofa seat to
open, extend, and convert
into a bed.
Figure 5-7. Filler Strip Attached to the
Seat Portion
There may also be a swivel rocker/recliner with adjustable headrest; it is also
coordinated with the décor of the motor home.
Figure 5-9. Sofa Bed in Open Position
Figure 5-10. Sofa Bed in Closed Position
The driver’s seat (Figure
5-11) is an electric-powered, six-way power seat (i.e., movement: up, down, forward tilt, reverse tilt) having
5-4
C A B I N E T S
&
F U R N I T U R E
swivel features (and recline features for the passenger seat only). When the motor home is parked, the driver’s
seat can be swiveled to face into the living room.
To swivel this chair, first extend the slide-out room (see Chapter 8 for additional
detail). Then move the chair backwards as far as possible to gain clearance from the
steering wheel. Now the chair can be swiveled without interference. The control
switch for the driver’s chair is located on the left-hand side in front of the power base
controls. In a comparable manner, the passenger’s seat is also an electric-powered, sixway seat having essentially the same controls as that of the driver’s seat and it is
operated accordingly.
Figure 5-11. Captain’s
Chair
Bedroom Area
If a décor-coordinated, quilted bedspread with accessorized pillow shams and accent pillow(s) are included with
the bedroom suite, it is recommended that
the bedspread be dry-cleaned only to
preserve the quality and integrity of the
bedspread for the longest time possible
(Figure 5-12).
Treatment of the bedspread with any of the
commercial, stain-resistant sprays (e.g.,
Scotchgard or its equivalent) will also make
the bedspread more resistant to the
possibilities of stains and fabric damage.
If maintained properly, the bedroom softgoods accessories will provide years of
dependable service and maintain the desired
décor established by the motor-home
owner.
Figure 5-12. Bedroom Decor
5-5
S T R U C T U R A L
F E A T U R E S
Chapter
6
Structural Features
6-1
S T R U C T U R A L
F E A T U R E S
Chassis Features
The chassis of your Tiffin Motorhomes Zephyr was built and is warranted by Spartan, the chassis
manufacturer. The operating instructions for that chassis are included in the Chassis Owner’s Manual which is
provided with your Zephyr and is a part of the Owner’s Information Package
furnished to you by your Tiffin Motorhomes Dealership.
Before you begin using your Zephyr, please read and follow all recommendations
for the proper care, operation, and maintenance of the chassis—this will assure you
of pleasant, trouble-free use of your motor home.
Figure 6-1. Spartan Chassis
Should you have any questions about the chassis, however, you should contact
your chassis manufacturer as noted in the literature described earlier.
TYPICAL CHASSIS ITEMS COVERED UNDER WARRANTY BY THE CHASSIS MANUFACTURER
Steering Wheel
Steering System
Instrument Panel
Engine
Transmission
Chassis Frame
Axles
Fuel Tank
Suspension and Springs (Front-End Alignment is not covered)
Tires and Wheels
Brakes
Exhaust System
Leaf Springs
Alignment
The Zephyr motor home you have purchased has been aligned at the factory prior to shipment to you. During
the first 10,000 miles of operation of your Zephyr, the chassis will have a tendency to “settle” and readjust itself
in response to the loading of your motor home.
Although it normally is not necessary to realign the Zephyr before the first 10,000 miles of use; it is,
nonetheless, recommended that you have the Zephyr alignment checked after the first loading of the motor
home. However, if you feel that you have noted some discrepancy or anomaly in steering operation, please
contact your chassis manufacturer or call Tiffin Customer Service at (256) 356-0261 to address your concerns.
6-2
S T R U C T U R A L
A typical Zephyr floor plan is shown below.
6-3
F E A T U R E S
E L E C T R I C A L
F E A T U R E S
Chapter
7
Electrical Features
7-1
E L E C T R I C A L
F E A T U R E S
General Information
There are two electrical systems in your Zephyr motor home—these are the 12-volt DC (VDC) system and the
120-volt AC (VAC) system. Most standard appliances require the 120-VAC system, while the majority of the
lighting systems used in the Zephyr use the 12-VDC system.
The electrical power for the 12 VDC system is supplied by the batteries of the Zephyr; those batteries are, in
turn, charged by a power converter. The electrical power for the 120 VAC is supplied by the electrical power
hookup cord when the Zephyr is connected to an external power source or when the on-board electrical
generator is in operation.
If installed, the optional inverter can also supply 120 VAC electrical power (to limited outlets and limited
appliances)—the inverter transforms the 12 VDC electrical power from the batteries into the 120 VAC
electrical power for the basic appliances.
Caution
Failure to turn off the 120 VAC appliances when starting or stopping the generator may
damage the transfer switch and/or electrical appliances.
To connect the Zephyr to an external source of 120 VAC electrical power, it is first recommended that all of
the circuit breakers (Figure 7-1) are in the “off”
position—this is done to prevent any power surge
upon connecting the motor home to the external
power source.
Then unwind the power cord
(Figure 7-2) from the
electrical
compartment
located in the compartment
behind the driver’s-side rear
Figure 7-1. Circuit Breakers Located Under Refrigerator or in
Bedroom Closet
tires. The standard, flexible,
power cord supplied with the
Zephyr is designed to handle up to 50 amperes.
Figure 7-2. Electrical
Power Hookup Cable
Make sure that the pins in the male end of the plug are oriented correctly so that they
match the power cable, and that they are in good condition (i.e., aren’t bent or
damaged). If there is a circuit breaker switch at the “plug” end of the power cord, that
7-2
E L E C T R I C A L
F E A T U R E S
breaker should be turned “off” before making the connection. Insert the plug into the mating outlet and then
turn the circuit breaker “on.”
Close and lock the electrical compartment door to protect the contents and to keep them clean and dry. Close
the cover on the power box, if so equipped, to avoid an unintentional disconnection and to keep the contents
clean and dry. Then switch the main breaker to the “on” position.
When properly connected, the 120 VAC system provides power to all the 120 VAC circuits and outlets when
the main breaker is turned “on.”
Circuit-Breaker Boxes
For the Zephyr, the 120 VAC breaker box and a separate 12 VDC breaker box (Figure 7-3) are typically located
beneath the refrigerator or in the bedroom [if inside the vehicle] or in
the storage box [if outside the vehicle]. The circuit breakers and
associated fuses are installed to protect the electrical system of
the Zephyr from any overloads. Do not attempt to change the
electrical circuitry or to add appliances yourself.
Please consult an authorized Tiffin Motorhomes Dealership or
Tiffin Motorhomes, Incorporated in Red Bay, AL to determine
whether any changes you desire are appropriate and acceptable.
Tiffin Motorhomes’ qualified staff of electricians can readily determine whether any changes sought (e.g., CB
radio, amateur radio, personal computer system, and the like) are possible or not and can advise you on how
best to realize these enhancements.
Figure 7-3. Circuit Breaker Box
Please note that the 12VDC fuses are located in the same compartment in the same distribution bay as the 120
VAC breakers. Fusing is provided for the following 12 VDC circuits: All interior decorative and overhead
lighting, water heater, TV switching box, slide-out lights, power roof vents, monitor panel, and passenger-side
console switch panel.
Additional 12 VDC fuse panels (Figure 7-4) are located in the front storage
compartment on the driver’s side; these fuse panels provide protection for
the following circuits: Mirrors, fog lights, hydraulic jacks, camera, wipers,
docking lights, dashboard panels, spot light, power seats, radio, step cover,
satellite receiver, 30-ampere ignition breaker, 50-ampere ignition breaker,
and dashboard air circuit breaker.
These fuse panels are protected by a plexiglass shield to prevent accidental
short-circuiting of the 12 VDC power system. To protect this 12 VDC
system further, DO NOT STORE anything in this compartment (e.g.,
toolbox) which may jostle around, break through the shield, and short out the 12 VDC system—if this system
were short-circuited, extensive damage and/or fire could result. Located on the passenger-side rear
compartment is another circuit panel which contains the following circuit breakers: Slide-outs, 12 VDC
disconnect, storage box lights, and solenoids.
Figure 7-4. 12 VDC Fuse Panels
7-3
E L E C T R I C A L
F E A T U R E S
Warning
When any fuse is to be replaced, never replace a blown fuse with another fuse with a
larger current rating (e.g., amperes) than the original rating of the fuse being
replaced—to do so would probably damage circuits and/or equipment and cause harm,
injury, or death to nearby persons.
Auxiliary Start Switch
The auxiliary start switch is located on the driver’s-side switch console box (Figure 7-5). This switch briefly
connects the Zephyr coach batteries to
the chassis batteries which, in turn,
allows the chassis batteries to “borrow”
power from the coach batteries to
assist in starting the engine.
If the chassis batteries cannot
themselves start the engine in the
“normal” mode, hold down the
battery-boost switch and retry starting
Figure 7-5. Driver’s Side Switch Console
the engine.
By using the battery-boost switch while trying to start the Zephyr engine, a jump-start situation is realized
between the coach and chassis batteries.
If the battery-boost switch is required to start the engine on a regular basis, ask your Tiffin Motorhomes
Dealership to check the chassis batteries and the associated charging system.
Battery Inspection and Care
The 12-VDC electrical-power system consists of four 6-VDC batteries wired in a series-parallel combination to
provide a final, 12 VDC system providing up to 450 Ampere-hours (A-hr) of service.
As the batteries contain a significant, and potentially lethal, amount of electrical energy; they must be handled
with due diligence and care. Some of the routine precautions include:
7-4
E L E C T R I C A L
F E A T U R E S
Warning
Remove rings, metal watchbands, and any other metal jewelry before working around
batteries.
If any metallic object (tool, jewelry, etc.) contacts the positive battery
terminal or any connection made to that terminal AND also contacts the negative
terminal or any of its connections, a SEVERE ELECTRICAL SHORT will occur which could
result in an explosion, fire, and/or personal injury. Lead-acid batteries contain diluted
sulfuric acid which can be dangerous; avoid direct contact with any battery fluids.
Always wear eye protection while servicing batteries.
Caution
Disconnect the 120 VAC electrical power cord and the negative terminal from the coach
batteries BEFORE working on the Zephyr electrical system.
Caution
If the Zephyr ever requires any welding operations on the frame, first disconnect the
chassis batteries. Failure to do so will destroy all of the chassis computer system.
When batteries (Figure 7-6) are not used for extended periods
of time, they will gradually lose their electrical charge.
Therefore, it is necessary periodically to recharge the batteries
to increase the operational lives of the batteries. It is also
necessary to check the external condition of the batteries on a
regular basis. Look for cracks in the battery case and cover.
Check the vent plugs and replace them if they are cracked or
broken. Keep the battery clean.
Figure 7-6. Maintenance Free House Batteries
(Compartment)
Since accumulations of dirt and acid residue around the
battery terminals may provide an electrical path for
discharging the battery, the area around the terminals should
be cleaned periodically. One can use an old toothbrush and a
7-5
E L E C T R I C A L
F E A T U R E S
sparse amount of a diluted solution of baking soda (sodium bicarbonate) and water (distilled or de-ionized,
preferred; tap water, acceptable) to clean and neutralize any acidic build-up around the battery terminals.
If there is any foaming on the top of the battery, this indicates that acidic residues are being neutralized. Rinse
the cleaned areas thoroughly with distilled or de-ionized water (tap water is okay, too).
Avoid getting the baking-soda solution into the battery fill plugs to each battery cell; this would drastically
reduce the effectiveness of the battery (by neutralizing the sulfuric acid in the battery cells) or, worse, “kill” the
battery. Dry the battery cables and terminals to prevent corrosion; to protect those terminals further, use a
plastic ignition spray on the terminals. Do not use grease on the terminals, especially on the metal-to-metal
connections, as grease may act as an insulator and keep the battery electrical power from entering the cables. If
the batteries are not going to be used for an extended period of time, they should be removed from the Zephyr
and stored in a warm, dry place. IT IS STRONGLY RECOMMENDED that this service be performed by a
qualified service technician, as the process is usually too complicated for the average owner to perform.
For those who may wish to perform this service themselves, the following procedure is described: Mark the
battery cables (“+” [plus] sign or “red” for the positive cable; “-” [minus] sign or “black” for the negative cable)
so that they can be properly reconnected again later. Then disconnect the negative terminal(s) from the
batteries. Afterwards, disconnect the positive terminals. Now the batteries can be removed for storage. When
the batteries are moved, keep them upright at all times. To reinstall the batteries at a later date, reverse the
above-described process. While in storage, these batteries would require periodic recharging to maintain their
full charge.
Additionally, the batteries will, over time, lose some of the water used with the sulfuric acid in the batteries.
Following manufacturer’s recommendations as found in the Owner’s Information Package, periodically check
the fluid levels in all the cells of the batteries (be sure to use safety eyewear during this process) and fill those
that are low with water (distilled or de-ionized water is preferred; tap water is okay).
Don’t overfill the cells; follow the filling directions exactly. This battery checkup should be done on a regular
basis to realize the fullest service possible from the batteries over the longest time possible. If the Zephyr is to
be stored for an extended period of time, the 12 VDC battery system should be disconnected—this will
prevent unnecessary drain and corrosion of the batteries and their terminals.
Battery Disconnect Panel
The battery disconnect panel is located inside the battery storage compartment. There is a rotary switch (Figure
7-7) on the upper left-hand side of the compartment which can disconnect the
engine battery when the vehicle is to be stored
for any appreciable time. Rotating this switch
disconnects the engine batteries only, not the
house batteries. This feature is designed to
prevent the engine batteries from being drained
during storage. This switch also disconnects all
the 12 VDC circuitry from the batteries; thus
Figure 7-7. Rotary Switch to
Disconnect Engine Battery
removing the total electrical load from those
batteries, with the exception of the LP detector.
7-6
Figure 7-8. Rotary Switch to
Disconnect “House”
Batteries
E L E C T R I C A L
F E A T U R E S
On the upper, right-hand side of that compartment is another rotary switch (Figure 7-8) which, when activated,
disconnects the “house” batteries (i.e., the 12 VDC system for the motor home). When the Zephyr is to be
stored for any length of time, it is wise to disconnect these two 12 VDC systems.
When the Zephyr is removed from storage, rotate the upper, left-hand switch to reconnect the 12 VDC
circuitry to the coach batteries again and rotate the upper, right-hand switch to reconnect the “house” battery—
the 12 VDC systems are now reactivated. The Spartan chassis of the Zephyr may be equipped with a second
disconnect switch strictly for the chassis batteries.
If your Zephyr is so equipped, this “master kill switch” may be located in the rear engine compartment. This
switch disconnects all power to the coach so that the coach cannot be started. This switch is used to prevent
the ignition circuitry from being accidentally turned on when the engine is being serviced.
For routine, short-term use, there is a “12 VDC disconnect” switch (Figure 7-9) on the switch console located
in the stairwell of the Zephyr. This switch—located in the upper, left-hand corner of the
switch console—can be used to disconnect the “house” battery from most of the 12
VDC circuits in the motor home so that there is no inadvertent drain on the battery
while the owner is away from the motor home (e.g., shopping trips, day trips for
sightseeing).
It is a good idea to develop the habit of disconnecting the 12 VDC “house” battery
system whenever one leaves the motor home for the better part of a day so that the
“house” battery is protected. Additionally, it is worthwhile periodically to check the fluid
levels in the batteries constituting the 12 VDC “house” battery system to make sure that
all fluid levels are properly maintained; otherwise, a full charge cannot be maintained in
the batteries.
Figure 7-9. 12 VDC
Disconnect Switch
120-Volt AC (VAC) Receptacles
Your Zephyr Motor Home is equipped with several 120 VAC receptacles (Figure 7-10) located throughout the
interior of the motor home. These 120 VAC receptacles are of the “threeprong” variety; the third prong being a grounding pin which provides
adequate grounding to protect one from any electrical shock.
For these receptacles to work properly, do not use an adapter, cheater, or
extension cord which defeats the function of the grounding pin. For the
same reason, never remove or bend away the ground prong or pin from any
three-prong AC plug so that it would fit a two-prong AC receptacle (i.e., an
ungrounded AC receptacle).
Figure 7-10. 120 VAC Outlets
Never operate the Zephyr if there is an electrical short present, as an electrical short may deliver an electrical
shock to anyone coming in contact with the exterior of the unit. If you should feel even the slightest of
electrical shock, immediately disconnect the unit from the 120 VAC power source and locate the electrical fault
(i.e., typically, it is a break in the grounding circuit).
7-7
E L E C T R I C A L
F E A T U R E S
Do not reconnect the 120 VAC power until after that electrical fault is fixed—the grounding circuit must be
continuous from the frame to the distribution panel, to the power cord, and to the earth ground so that
electrical-shock protection is realized.
12-Volt DC (VDC) Receptacles
Your Zephyr Motor Home is equipped with a 12 VDC receptacle conveniently located on the
dashboard or bulkhead. This 12 VDC receptacle can be used for providing power to various
items, such as cellular phones or personal computers or portable communications equipment.
This receptacle is usually found on the bulkhead or on the dashboard (i.e., the connector in
Figure 7-11) in front of the passenger’s seat so that it is conveniently available to be used by
the personnel in the cockpit area.
Figure 7-11.
12 VDC Outlet
Ground-Fault-Circuit-Interrupt (GFCI) Receptacles
In the kitchen and bath areas, there are 120 VAC GFCI receptacles (Figure 7-12) which provide greater
protection against inadvertent electrical shocks. These specialized GFCI receptacles provide both overload and
short-circuit protection for the user. The electrical receptacles located in the slide-out(s) are wired through the
kitchen GFCI. The exterior receptacles are wired through the bathroom GFCI.
Consequently, if an appliance plugged into a slide-out or exterior receptacle is not
working, check for a tripped GFCI in the kitchen or bathroom.
In addition, these receptacles protect the user from ground faults between an electrically
“hot” wire and ground. The GFCI will not reduce the shock hazard if the short is
between a neutral and “hot” wire or two “hot-lead” wires.
Figure 7-12. GroundFault Circuit
Interrupter (GFCI)
The GFCI should be tested at least once a month. The 120 VAC electrical system must
be “on” for the GFCI to be tested. To test the GFCI the reset button needs to be
pushed in fully before starting the test. Push the test button; this will cause the reset
button to pop out which means that the protected circuits have been disconnected.
Push the reset button back in until a “click” is heard—this will re-activate the protected
circuit. If the GFCI is working properly, the reset button will remain in the “in”
position.
ICC [Interstate Commerce Commission] Switch
On the driver’s side console, one will notice a switch (Figure 7-13) labeled “ICC.” This
switch is a momentary pushbutton switch–it is active only when the switch is being
pressed. This switch enables the driver to communicate with other traffic by flashing
the clearance and sidelights of the Zephyr.
Figure 7-13. ICC
Switch
If the lights are presently “on,” the switch will momentarily turn them “off.” If the
7-8
E L E C T R I C A L
F E A T U R E S
lights are “off,” the switch will momentarily turn them “on.”
Inverter / Converter
When the 120 VAC power is not available, either from the power cord or the generator, the optional
inverter/converter (Figure 7-14) may be used. The control
panel for the inverter/converter is located above or near the
entrance door.
When the inverter/converter is turned “on,” it transforms the
12 VDC power to 120 VAC power for the operation of lights,
appliances, televisions, and related items. The 120 VAC
power which is generated by the inverter/converter is routed
to the electrical sub-panel located next to the main breaker box
under the refrigerator [if inside the vehicle] or in the storage
compartment [if outside the vehicle].
The internal battery charger and automatic transfer relay
Figure 7-14.
allows operation as either a battery charger or inverter (but not both at the same
Inverter/Converter
time). An external source of AC power (such as shorepower or a generator)
must be supplied to the inverter AC input in order to allow it to operate as a battery charger. The charger will
always charge when there is AC power present, even when the inverter itself is turned off (by the on/off
switch). When operating as a charger, the AC output is powered by the external source (such as a generator or
public power).
The inverter automatically becomes a battery charger whenever AC power is connected to its AC inputs. There
is a minimum 20-second time delay from the time the inverter senses that AC is present at the input terminals
to when the transfer is made. This delay is built in to provide time for a generator to spin-up to a stable voltage
and avoid relay chattering. The inverter will not transfer to generator until it has locked onto the generator’s
output. The inverter’s AC input is internally connected to the inverter’s AC output while in the battery charger
mode.
Automatic Generator Switch
The Energy Command 30 (EC-30) is an Automatic Generator Starting System that provides both automatic
and manual control of the generator (Figure 7-15). EC-30 also provides
critical system information such as the battery state-of-charge, key operational
information such as quiet time, genset service and fault messages. EC-30
automatically starts the genset when the battery becomes discharged or when
there is a run request from an external device (i.e. heating/cooling system).
When the battery is charged or the heating/cooling system no longer requires
power, the genset is automatically turned off.
Figure 7-15. Automatic
Generator Switch
7-9
E L E C T R I C A L
F E A T U R E S
The EC-30 AUTO ON Mode requires a confirming keystroke (first AUTO GEN, then ENTER to confirm).
This reduces risk of unintended AUTO ON operation. The motor home can use the AUTO ON or QUIET
ON mode while traveling if the operator reactivates AUTO ON mode. However, each time it is signaled by the
safety input, the genset will be stopped and the Mode will change to MANUAL. If automatic operation is
desired, press the AUTO GEN key after parking.
Warning
DO NOT run the genset--use the EC-30 AUTO ON or QUIET ON modes--when the RV is
indoors or in a confined space. Asphyxiation or carbon monoxide poisoning hazards
exist wherever genset exhaust gases can accumulate. Exposure to carbon monoxide,
moving parts, and electricity hazards is possible due to unexpected automatic starting.
The EC-30 maintains a record of the last change of the Safety Input signal. If the EC-30 does not see the Safety
Input change in 30 days, it will prompt the user to re-verify the Safety Input by activating the safety signal (i.e.
switching the ignition, changing transmission position, or operating the parking or trailer brake).
The AUTO GEN is used to select the MANUAL, AUTO ON, or QUIET ON genset operating Mode. If the
Mode is not displayed, pressing AUTO GEN immediately exits to Local Time and genset Mode.
In MANUAL, the genset may only be operated by using a START/STOP switch.
In AUTO ON the genset will start based on HVAC run requests and low battery regardless of time of day.
In QUIET ON Mode the genset will not automatically start during Quiet Time. Prior to Quiet Time the
battery state-of-charge is checked, and if needed, the genset is started to charge the batteries before Quiet Time
begins.
Caution
Use of the automatic modes is not allowed if the house battery voltage is below 9 volts.
Before storing or servicing, disable the Automatic Generator Starting System by
disconnecting battery of genset remote harness.
7-10
E L E C T R I C A L
F E A T U R E S
Electrical Generator
The electrical generator (Figure 7-17) is located in a compartment in front of the motor home between the
chassis rails on pull-out slides. The generator is mounted on slides for easy access; however, the slides must be
unlocked before free movement is possible.
There is a “pull” cable (Figure 7-16) in the
box in front of the driver’s-side front tire—
pulling this cable will release the slide lock for
the generator.
Prior to starting or stopping the generator,
make sure that all the 120 VAC appliances are
Figure 7-16. “Pull” Cable
for Generator Release
turned “off.” After the generator has
been started, wait until the transfer switch
has connected before turning “on” any of the appliances.
Figure 7-17. Electrical Generator
The generator can be started from either the remote-start switch located on the dash or directly at the generator
itself. The hour meter installed on the generator records the number of hours of operation of the generator
motor—this elapsed time is needed for observing necessary maintenance schedules on the generator.
Caution
Failure to turn “off” the 120 VAC appliances when starting or stopping the generator
may damage the transfer switch and/or electrical appliances.
For more detailed operating instructions of the generator and to determine necessary preventive-maintenance
schedules and procedures, review the manufacturer owner’s manual.
Automatic Transfer Switch
Your Zephyr is equipped with an automatic transfer switch. When the generator is turned “on,” this switch
automatically transfers from external power to generator power. There will be a slight delay between the start
of the generator and the electrical connection being made—this delay allows the generator to reach normal
operating speed without needing to supply a required load.
When the Zephyr is plugged into an external source, a “click” will be heard in the transfer switch box—this is a
normal function and merely indicates that the unit is changing over from an external power source to the
generator.
7-11
E L E C T R I C A L
F E A T U R E S
Resettable Circuit Breakers
The resettable circuit breakers (Figure 7-18) are located within 18 inches of the source of power; that is, the
converter and the battery. When the circuit breakers are shut down or electrically
tripped, they must be manually reset. To find the circuit breakers, follow the line
from the battery or converter approximately 18 inches—this may lead to a
junction box or to a cabinet inside the Zephyr or to a similar location.
As needed, manually reset the circuit breaker or breakers as shown in the
accompanying picture. Be careful when working around these connections as an
accidental, electrical short to ground (i.e., momentarily connecting the “positive”
Figure 7-18. Resettable
Circuit Breakers
or “hot” terminal to any part of the chassis) can be potentially hazardous and
harmful.
Towards this end, don’t store in this particular storage compartment anything which may move around in
transit and subsequently cause any electrical short circuits or anything that is flammable.
Fuse Blocks
Some of the electrical circuitry within the motor home is protected by various fusing systems. Some of these
fuse blocks are immediately accessible from the driver’s side underneath the dashboard. Underneath the
dashboard is an enclosure which contains fuse blocks. These fuse blocks protect some of the major electrical
systems of immediate concern to the driver such as the power seats (driver’s and passenger’s), spot light,
mirrors, camera, radio, and various extra fused positions.
Should there be any electrical failure of these components or systems, the first troubleshooting procedure
should be to check the fuses and have available replacements to replace any blown fuses, as may be warranted.
Also the Zephyr contains a computerized diagnostic center, located beneath the access panel on the dashboard
pod, for the engine of the motor home. This center permits a computer to be connected to the onboard
diagnostic center monitoring many of the operating functions and parameters of the engine so that the current
operating status of the engine can be determined and any anomalies or problems may be noted.
This diagnostic tool enables the motor home owner to maintain an updated status of the engine so that the
overall reliability of the motor home can be maintained.
As an aid to extracting and/or installing fuses in the fuse blocks, one may wish to buy an inexpensive fuse
puller at any electronics or hardware store. This tool makes the installation or removal of fuses much easier and
prevents inadvertent damage to nearby fuses or the fuse block itself.
Whenever a fuse has been “blown” and is to be extracted and replaced, it is good practice to examine the wiring
going to that particular fuse to see if there is any noticeable degradation (e.g., wiring insulation nicked, missing,
or melted) which may indicate damage beyond the fusing proper.
7-12
E L E C T R I C A L
F E A T U R E S
Warning
Never replace a fuse with a fuse rated larger than that which originally came from the
factory. To do otherwise will cause serious damage, overheating of the wiring, and
possible ignition of nearby materials resulting in a fire.
Seven-Pin Towing Connector
Your Zephyr is equipped with a standard, 7-pin connector near the towing hitch at the rear of the motor home
to supply the necessary circuitry to control a towed vehicle. The wiring of that connector is shown in Figure 719.
Make sure that any cable from the vehicle to be towed is wired correctly to mate properly with the connections
shown in the connector. If in doubt
about proper wiring, have a qualified
service technician prepare and install
the necessary cable to mate with the 7pin connector on the motor home to
assure proper operation subsequently
when any vehicle is actually towed by
the motor home.
When the towed vehicle is uncoupled
from the motor home and the cable is
disconnected from the 7-pin
connector, be sure to close the springhinged cover plate on the connector to
Figure 7-19. Bargman 7-Way Round Towing Connector
protect the contact pins from dirt or
debris. In a similar manner, protect the cable end from similar damage, weather, or debris—one such method
could be to place the connector end in a heavy-gauge plastic bag (e.g., polypropylene, polyethylene, etc.) and
secure the bag tightly around the cable with a stout elastic band or tape and then mount the secured cable in a
manner to keep it both from mechanical damage and water intrusion.
When the towed vehicle is again coupled to the motor home via the towing hitch and the cable is again
connected to the 7-pin connector, make sure the resultant connection is tight and solid so that the connection
won’t jar loose during use. Several supplemental methods to secure that connection have been used; some of
which include securing the connection with a strong rubber band or with Velcro-type fasteners to provide a
supplemental mechanical backup to the actual electromechanical connection.
7-13
S L I D E - O U T
F E A T U R E S
Chapter
8
Slide-Out Features
8-1
S L I D E - O U T
F E A T U R E S
SLIDE-OUT OVERVIEW
Warning
BEFORE ACTIVATING THE SLIDE-OUT FEATURES, please read the slide-out room
instruction manual first. Additionally, the motor home must be parked and the leveling
jacks must be used to level the motor home PRIOR to activating the slide-out features.
General Considerations
Please Note
The Slide-Out Room requires semi-annual inspection (i.e., every six months) to assure
that the slide-out mechanism is properly aligned and functioning correctly. Please
make sure that this inspection is performed every six months to correct any possible
misalignments.
The slide-out-room feature is actuated by means of a readily accessible, rocker
switch (Figure 8-1). The rocker switch must be manually held down in the
desired position (i.e., either “in” or “out”) to activate the desired action of the
slide-out room and continue to be held down until the desired action is
concluded. NOTE: The rocker switch for the slide-out will only operate
when the ignition switch is in the “off” position—there is an interlock which
keeps the slide-out mechanism from operating when the ignition is “on.”
Releasing the rocker switch before the slide-out is fully extended or retracted will
stop the slide-out at some intermediate position.
Figure 8-1. Slide-Out Switches
Operating Precautions
Warning
Before attempting any extension of the slide-out room, check outside and make sure
that there is at least a five-foot clearance around the area where the slide-out room will
8-2
S L I D E - O U T
F E A T U R E S
be extended.
Before the slide-out-room mechanism is to be used, make sure that the motor home is parked, the leveling
process has been properly completed. Verify that no obstacles (e.g., branches, trees, telephone poles,
power/water hookups, trash bins, and the like) are within a five-foot space envelope of that slide-out room to
preclude damaging the slide-out room when it is finally deployed.
Extending the Slide-Out Room
1. All windows in any slide-out room (Figure 8-2) must be closed and secured before that slide-out room
is to be extended or retracted. Also any loose materials or possible obstructions should be removed
from the immediate slide-out room area. Make sure the motor
home has been leveled. Make sure that the battery is fully
charged and connected to the electrical system.
2. Verify that there are no obstructions outside which may
interfere with the operation of the slide-out room.
3. Prior to moving the front slide-out room in either direction,
make sure that the driver’s chair is moved forward into the
Figure 8-2. Typical Zephyr Slide-Out
driving area as far as possible and is locked into position.
4. Make sure that the ignition switch is in the “off” position prior to using the slide-out function; if the
ignition switch is “on,” the slide-out mechanism won’t work.
5. Push the “out” portion of the rocker switch; allow the slide-out room to go to its fully extended
position—at this point, release the rocker switch (this locks the room into position).
Retracting the Slide-Out Room
1. Before attempting to move the motor home, any slide-out room(s) must be fully retracted.
2. Verify that the battery is fully charged and connected to the electrical system.
3. With the ignition switch in the “off” position, push the “in” portion of the rocker switch; allow the
slide-out room to go to its fully-retracted position—at this point, release the rocker switch (this locks
the room into position).
8-3
S L I D E - O U T
F E A T U R E S
Manual Operation: Slide-Out Room
Your Power Gear slide-out system is equipped with a manual override that allows one to extend or retract the
room in the event of a loss of power.
Please Note
If the slide-out room doesn’t move when the rocker switch is depressed, check the
following:
Make sure the ignition switch is turned “off.”
Make sure the battery is fully charged and connected.
Make sure the slide-out breakers haven’t been “tripped”—these breakers are located in
the storage box with the inverter/converter.
After the previous items have been checked and verified and the slide-out room
still does not move when the rocker switch is pressed, follow these simple steps
(Figure 8-3) to override the slide-out room manually.
Figure 8-3. Manual Slide-Out
Deployment Sequence
1. Turn “off” the ignition switch.
2. Locate the slide-out electrical controller (refer to your Tiffin
Motorhomes dealer or the Tiffin Motorhomes factory for its location).
There are two versions of the controller. For version 1, unplug the sixpin wiring harness to the controller. For version 2, remove one of the
motor leads (either the motor I or the motor II lead from the
controller).
3. Locate the slide-out motor; it will be mounted to one side of the slideout rails. NOTE: If the motor home has an underbelly or a cover over
the motor, these parts must be removed for access.
4. Rotate the brake lever, on the backside of the motor, counter-clockwise
(CCW) (looking from the rear of the motor) about 1/8 of a turn to the
released position. This action will release the brake that holds the room in place.
5. Locate the manual override for the slide-out system.
8-4
S L I D E - O U T
F E A T U R E S
6. The room is now free to move. Using a ¾” wrench, crank the room either “in” or “out” completely
(depending on your needs). NOTE: If the slide-out system is supplied with a gearbox override
(optional), use the crank handle to move the room.
7. When the room has fully moved “in” or “out,” apply pressure to the wrench or ratchet and return the
brake lever to its engaged position—this will assure that the room is locked into a secured position.
8. Take the unit to an authorized dealer for service.
Manual Operation: X-Slide Room Extension
Your Zephyr may be equipped with a hydraulic X-Slide room extension. In the event that your Zephyr’s XSlide room extension fails to operate properly, you may manually operate the X-Slide by following the
instructions below:
1. Turn the ignition switch to “off.”
2. Locate the hydraulic pump (Figure 8-4). It will be located in one of two locations: between the chassis
rail in the main compartment of the basement OR behind the last compartment door on the passenger
side of the motor home.
3. Open the emergency retract valve. The emergency retract valve relieves the pressure off of the
cylinders. This allows the room to be moved in and out freely.
4. From the outside of the motor home, you will need to push the slide-out box “in.”
5. Locate the front fascia panel (Figure 8-5) inside the motor home. It will be located directly behind the
passenger’s seat. Using a Philips head screwdriver, remove the panel.
Figure 8-5. Front Fascia Panel
Figure 8-4. Hydraulic Pump
8-5
Figure 8-6. Front Fascia Panel;
Threaded Rod Inserted into
Hole
S L I D E - O U T
F E A T U R E S
Figure 8-8. Slide-Out Retention
Clamp Positioned between
galley sink and cabinets
Figure 8-7. Slide-Out Retention
Clamp
6. Once the panel is removed, you will be able to locate the opening to insert the threaded rod. Rotate the
threaded rod clockwise 12 complete turns (Figure 8-6). After rotating the rod 12 complete turns on the
front side, you will pull the back side (by hand) to keep the room coming in straight. Pull the back end
just far enough to keep it even with the front side. Keep alternating from front to back by rotating the
rod 12 turns and pulling the back side in until the room is completely retracted. Locate the slide-out
retention clamp (Figure 8-7). In the area between the galley sink and cabinets (Figure 8-8), you will need
to install the clamp on the back side. Press the retention clamp firmly against the C-channel portion of
the slide mechanism. The threaded rod on the front side secures the room while the clamp secures the
room on the back side. NOTE: Make sure the room does not bind while performing this operation.
NOTE: DO NOT extend the room until steps 7 and 8 have been completed!
7. Close the emergency retract valve. DO NOT over tighten!
8. Using a counterclockwise rotation, completely back out and remove both threaded rods.
8-6
S L I D E - O U T
F E A T U R E S
PLEASE NOTE
Use the leveling jacks to keep your motor home level during the above listed
procedure. This will make it easier to push/pull the room in.
The room will need to be locked into place before resuming operation of the motor
home.
If at any stage something is not understood or if the room begins to bind
DO NOT force the room.
Instead, contact HWH Customer Service for assistance at 1-800-321-3494.
8-7
E X T E R I O R
F E A T U R E S
Chapter
9
Exterior Features
9-1
E X T E R I O R
F E A T U R E S
Towing Hitch
On the rear of the Zephyr can be found a Class 3, 10,000-pound
towing hitch (Figure 9-1) capable of handling a tongue weight of
1,000 pounds. This hitch is installed for towing a passenger car to
be used when the motor home is parked. The wire connector
installed with this hitch is a standard, seven-pin connector. For
more information on the connector, please see Chapter 7 of this
Owner’s Manual.
Exterior Sides
Figure 9-1. Class 3 Towing Hitch
The sides of your Zephyr (Figure 9-2) are constructed of gel-coated
fiberglass. To enhance this feature, the end caps are also gel-coated
fiberglass. To clean these fiberglass surfaces, only use warm water
and a mild cleanser; gently wash with soft cloths. Use of stiff bristle
brushes or other harsh abrasives may cause scratches in the fiberglass
surfaces. Please note: Tiffin Motorhomes is NOT responsible for
the weathering and/or
oxidation of these gelcoated surfaces.
Lighted
storage
compartments
(Figure
Figure 9-2. Zephyr Exterior
9-3) are located on the
exterior sides of your Zephyr. All of these external storage
compartments provide ample, additional space for your
belongings while you are traveling. When stowing materials in
these storage compartments, try to “balance” the resultant
weight load from front to rear and from side to side—this will
keep the center of gravity of the motor home essentially
unchanged and should not adversely affect the handling
Figure 9-3. Typical Exterior Storage Compartment
characteristics of the motor home when it is in motion.
Security Lights
On the Zephyr, exterior security lights (Figure 9-4) are standard features. This
light is installed on the passenger side of the coach to help light that side of the
Zephyr for added protection. This light can serve as a “porch light” when the
motor home is parked and the awning is deployed so that various activities (e.g.,
sitting outside, grilling, visiting) at dusk and later can be enjoyed by the motor-
9-2
Figure 9-4. Security Lights
E X T E R I O R
F E A T U R E S
home owners and their guests.
Roof & Ladder
The Zephyr is manufactured with a fiberglass roof. Proper care and routine
maintenance of your roof will assure many years of trouble-free performance.
Please see Chapter 14 for details on recommended cleaning instructions. On the
Zephyr, a roof ladder [load limit: 200 pounds] (Figure 9-5) may also be included as
an additional feature. The ladder is typically used to permit easy access to the roof
for routine maintenance and periodic inspections.
The ladder comes in two sections; the upper section is attached to the motor home;
while the lower section is removable and must be stored after use. When attaching
the lower part of that ladder to its upper part, be sure that the ball-lock pin is
securely fastened through the locking device to secure the ladder assembly.
Figure 9-5. Ladder
Warning
Do not exceed the maximum rating of the ladder (i.e., 200-pound load limit).
Do not attempt to walk on the roof either while it is wet or when condensation is
present from the air-conditioning system, as that surface would be quite slippery.
Hydraulic Leveling Jacks
Warning
If the vehicle is equipped with a slide-out, DO NOT OPERATE any room extension until
the leveling and stabilizing procedure has been properly completed. DO NOT RETRACT
the leveling system until the slide-out room has been retracted. NEVER operate the
leveling system when the slide-out is extended.
The Zephyr is equipped with hydraulic-leveling jacks. These jacks work in pairs: Front, right side, left side, and
rear. Before extending these jacks, the engine must be “off,” the ignition switch must be in the
“ACC” position, and the transmission must be in “park.” The parking brake needs to be set and the
tires blocked securely; then the leveling jacks can be activated.
9-3
E X T E R I O R
F E A T U R E S
Caution
DO NOT LIFT the wheels of the motor home off the ground when leveling—if done, the
motor home can “lean” forwards or backwards when supported only by the leveling
jacks. Never use the jacks to lift the motor home off the ground to change the tires or
perform any under-chassis maintenance—these jacks are not meant for this type of
service and this misuse would be very dangerous to the operator.
HWH Leveling Control System
The HWH Computerized Leveling system (Figure 9-6) which requires minimal effort from the motor-home
user. For automatic leveling of the motor home, perform the
following steps:
Automatic Leveling:
1. Turn the ignition switch to the “acc” or “on” position.
The engine must be “off” to level the motor home. The
transmission shift must be in the position for parking.
The parking brake must be set either manually or
automatically. If the “not in park/brake” light on the
HWH console is “on,” check or re-check the shift and
brake position.
Figure 9-6. HWH Leveling Control Panel
2. Press the “hyd” button on the HWH console. The “hydraulic operation” indicator light will turn “on”
with a steady glow.
3. Press the “hyd” button a second time; the “hydraulic operation” indicator light will flash “on” and
“off,” the motor home will automatically level itself, then the system will turn itself “off.”
To store the hydraulic jacks prior to moving the motor home, perform the following steps:
1. Turn the ignition switch “on”; then store the hydraulic jacks immediately.
2. Press the “hyd” button once; the “hydraulic operation” indicator light will turn “on” with a steady
glow.
3. Press the “dump” button.
4. Press the “store” button; the “store” indicator light will flash while the jacks are being retracted.
9-4
E X T E R I O R
F E A T U R E S
5. When the “travel” light turns “on,” the jacks are fully retracted and the motor home may be moved.
The HWH Leveling Control system will turn itself “off.”
For manual operation (see Figure 9-7) of the hydraulic jacks, perform
the following steps:
Manual Leveling:
1. Turn the ignition switch to the “acc” or “on” position. The
engine must be “off” to level the coach. The transmission shift
must be in position for parking. The park brake must be set
either manually or automatically. If the “not in park/brake”
light is “on,” check or recheck the shift and brake position.
Figure 9-7. HWH Leveling Control Panel
2. Press the “hyd” button. The “hydraulic operation” indicator light will turn “on” with a steady glow.
3. On the right-hand portion of the HWH Leveling Control touch panel, note the outline of the motor
home and the various “raise” (i.e., “up” arrow and “lower”
(i.e., “down” arrow) touch buttons.
4. Press the respective “raise” (“up” arrow) button to raise the
respective side or end of the motor home. A yellow light
to the front, side, or rear of the motor-home outline
indicates that that side or end is low. The “lower” (“down”
arrow) buttons will lower the motor home.
NOTE: The hydraulic jacks (Figure 9-8) will always work in pairs:
Front, right side, left side, or rear.
Figure 9-8. Leveling Leg Under Chassis
Important
The leveling system should be cycled once a month or whenever the motor home is
used to keep the leveling system in good operating condition.
Electric Steps
The Zephyr is equipped with electric, three-step, doorsteps (Figure 9-9). The rocker
switch to operate these steps is located in the passenger console box. When the power
switch for the steps is in the “on” position, simply open the door and the steps will
automatically extend. Detailed operation for the electrical, three-step, doorsteps is as
follows:
Figure 9-9.
Entrance Step
9-5
E X T E R I O R
F E A T U R E S
1. Turn the step power switch “on.”
2. Close the door. The step should retract and lock into the UP position.
3. Open the door. The step should extend and lock into the DOWN position.
4. Turn the step power switch “off.” The step should remain in an extended position when the door is
closed. Turning “off” the power with the step retracted will hold the step in a retracted position, as
well.
5. With the step extended, turn the step power switch “off” and close the entrance door. Turn the vehicle
ignition switch “on.” The ignition override system will go into effect and the step will automatically
retract.
Caution
If the motor home is driven with the step in the extended position, there is the
possibility of causing major damage to both the step and the motor home.
6. With the step switch in the “on” position, turn the vehicle ignition switch “off” and open the door.
The step will extend and lock in the DOWN position.
Caution
If the door is opened and closed without allowing the step to extend fully and lock in
the “DOWN” position, the step will retract and lock in the “UP” position. When the door
is re-opened, the step will not extend. The power switch must be turned “on” for the
step to extend.
7. This feature is only operative the first time the door is opened after the vehicle ignition switch is turned
“off.” When the ignition switch is “on,” the step will always activate with the door movement,
regardless of the position of the step power switch.
9-6
E X T E R I O R
F E A T U R E S
Caution
Always be sure to “look before you leap”! When opening the entrance door from the
inside, be sure that the step has fully deployed before trying to step outside to avoid
falling and possible injury.
When the electric steps are fully retracted and the motor home is
being made ready for travel, be sure to deploy the cover over the
stairwell (use either the switch on the driver’s console or the switch
[Figure 9-10] on the passenger’s side) to protect any occupants of
the cabin from any accidental stepping into the open stair well.
Activating either switch will cause the stairwell cover (Figure 9-11)
to be pneumatically deployed from a recess beneath the floor in
front of the passenger’s seat. This precaution will provide a safe
Figure 9-10.
Entrance Step
Switch
traveling environment for anyone using the passenger’s seat during
travel.
Figure 9-11. Stairwell
Cover
Mirrors
This motor home is equipped with convex, remote-controlled, exterior, rear-view mirrors (Figure 9-12).
Always adjust the mirrors for maximum rear visibility prior to driving. If
another driver is to drive, be sure the mirrors are readjusted to accommodate
the second driver.
These standard chrome mirrors are adjusted by using the multi-directional
switch located on the dashboard. Select the mirror to be adjusted by pointing
the arrow in the direction of that mirror. Move the control in the direction
of movement desired to obtain the best view for that mirror. The
adjustment control moves the top half of both mirrors. The bottom half of
each mirror is convex and is adjusted manually.
Detailed instructions for these manual adjustments can be found in the
manufacturer’s literature available in the Owner’s Information Package.
However, this brief overview of mirror adjustment can begin the process:
The top portion of the mirror should be adjusted horizontally so that you can
see your own motor home in the one-inch surface closest to the motor
home; the remaining portion of the mirror now permits you to see the road
Figure 9-12. Rear-View Mirror
behind you. The mirror should be adjusted vertically so that you can see the
rear bumper on the bottom of the plane portion of the mirror.
9-7
E X T E R I O R
F E A T U R E S
The convex mirrors should be adjusted horizontally so that you can see your own motor home in 1/3 of the
mirror. These convex mirrors should then be adjusted vertically to allow you to see any other vehicles
alongside your motor home.
These mirrors also contain heating elements to defog or de-ice the mirror glass during cold weather operation.
The “on/off” switch for this feature is located by the adjustment control. Further adjustment of the mirror
may be necessary at the swivel portion of the mirror arm.
Important
Objects viewed in convex mirrors appear smaller and farther away than they actually
are.
9-8
I N T E R I O R
F E A T U R E S
Chapter
10
Interior Features
10-1
I N T E R I O R
F E A T U R E S
Bedspread
As a furnished part of the bedroom suite (Figure 10-1), a bedspread and matching pillow accessories are
included with the Zephyr motor home. Other bed linens
(e.g., sheets, blankets, pillows, pillowcases) are the sole
responsibility of the motor-home owner and are to be
provided by that owner.
For the bedspread and pillow shams, cleaning instructions
are “for dry-cleaning only,” as the bedspread was made
with materials treated for stain resistance; dry-cleaning will
prolong the life of these materials.
Minimizing exposure to unnecessary sunlight will prolong
and preserve the richness of the colors of the fabrics; so it
is advisable to keep the shades closed on the “sunny side”
of the motor home, whether parked or in transit.
Figure 10-1. Bedroom Decor
Flooring
The living room and bedroom floor areas are carpeted with filament-nylon carpeting treated with Scotch-guard,
a stain-resistant coating. In the Owner’s Information Package, there is additional literature from the
manufacturer concerning the specifics of caring for the carpeting which,
if followed, will prolong the appearance and life of the carpeting. Please
become familiar with the recommended care and cleaning of the
carpeting to assure its prolonged life.
Ceramic tile flooring (Figure 10-2) is standard in the kitchen and
bathroom areas of the motor home. For routine cleaning, sweeping or
vacuuming the floor would be sufficient.
If more thorough cleaning is warranted, the flooring can be cleaned with
a damp mop and water. For more stubborn stains, a mixture of soapfree household cleaner (e.g., vinegar, ammonia, or comparable products)
and water can be used to advantage.
One should not unduly saturate the floor surfaces with water, as this
could damage the flooring substrate. Feel free to use any abrasives
(cleansers, scouring pads; and the like) as they cannot scratch or mar the
Figure 10-2. Ceramic Tile Flooring
10-2
I N T E R I O R
F E A T U R E S
flooring surfaces and won’t cause any damage to the flooring.
Ceiling
The ceiling (Figure 10-3) in the Zephyr motor home is covered with a padded-vinyl headliner which can be
easily cleaned with a damp, soft cloth and a mild detergent. Take care to clean around any vent areas to prevent
any buildup of dirt, grease, or other accumulations.
When cleaning around any alarms (e.g., fire alarm, CO/LP gas detector, and the like), take care not to introduce
any water or dirt into the sensors of those alarms.
Window Treatments
Throughout the Zephyr, the window treatments consist of pleated day/night window shades (Figure 10-4)
which have two sections. When closing the shade,
the first section to become visible is the “day”
section which is translucent and permits outside,
ambient lighting to come into the motor home while
blocking visibility.
If the shade is continued to be closed, one
encounters the “night” section which places a
heavier, more opaque material over the window to
block out even more light from the outside.
The “night” setting is generally used in the evening
or when a greater degree of privacy is sought.
All of the curtains installed in the Zephyr are to be
dry-cleaned only; no water-based cleaning agents are
recommended as they may cause undue shrinking or
Figure 10-4. Window Treatments Featuring “Day” and “Night”
Settings
fading of the fabric.
On some windows, mini-blinds may be installed. Instructions for the proper use and cleaning of any miniblinds will be found in the Owner’s Information Package furnished with the Zephyr.
10-3
P L U M B I N G
&
B A T H
F E A T U R E S
Chapter
11
Plumbing & Bath Fixtures
11-1
P L U M B I N G
&
B A T H
F E A T U R E S
FRESHWATER SYSTEM
Monitor Panel
The monitor panel (Figure 11-1) permits checking the approximate levels in the fresh, gray, and
black water holding tanks; the LP-gas level; and the
condition of the house batteries. The monitor
panel is generally located in an overhead cabinet
above the passenger’s seat.
To use this monitor, simply press the desired status
button to obtain a read-out of the fresh, gray, and
black water tanks and the present condition of the
batteries.
Figure 11-1. Monitor Panel (Water, LP Gas, Battery)
The “empty” indicator light will momentarily light
when the button is pressed. If the tank is full, all of
the lights will be “on.” Lights are sequentially
arranged to indicate fluid levels in approximately
third-tank increments.
For example: if the tank selected is approximately two-thirds full, then the indicator lights “E” (for
“empty”), “1/3”, and “2/3” will all be lit at the same time.
On the right-hand side of the monitor panel is a water pump switch. The switch controls the power
going to the pump and is used to turn that power either “on” or “off.” There are other water-pump
switches nearby the sinks in the kitchen and the bathroom to enable convenient use of the water
system throughout the motor home.
Kitchen Sink
The kitchen sink (Figure 11-2) installed is a solid-surface,
double-bowl, stainless-steel sink equipped with two sink
covers to provide additional counter space when the sink
is not in use.
For the sink, cleaning care consists of washing only with
mild detergents and water and using a soft cloth for
subsequent drying and polishing. The faucet in the
kitchen is a single-handle faucet.
Figure 11-2. Kitchen Sink & Counter
11-2
P L U M B I N G
&
B A T H
F E A T U R E S
Bath Sink, Shower & Accessories
The sink (Figure 11-3) in the bathroom is a solid, continuous surface. When cleaning this surface,
use care to prevent scratching or marring it. The typical
bathroom accessories include a towel bar and a tissue holder.
Figure 11-3. Bathroom Sink
The double-handled faucet in the
bathroom was chosen to match the
specified decor. The bathing facilities
(Figure 11-4) installed may be a fiberglass
shower or combination shower/tub with
a glass shower door. The tub faucet with
showerhead, hose, and bracket are
coordinated with the sink faucet.
Figure 11-4. Shower
Water Pump
The water pump is self-priming and totally automatic, operating on demand whenever
water is required. The water pump is used to pressurize the freshwater system when the
unit is not connected to city water. The switches (Figure 11-5) to this pump may be
located in the bathroom, or sanitation-service compartment (Figure 11-6). To start the
pump, follow these instructions:
1. Fill or partially fill the fresh water supply tank.
Fig. 11-5.
2. Open the kitchen and bathroom faucets.
Water
3. Turn the water pump switch “on” and allow the water to fill the water line and
Pump
Switch
the hot water heater.
4. Close each faucet after it delivers a steady stream of water (close the coldwater faucet first). Leave the hot-water faucets “on” until they also deliver
a steady stream of water. This procedure will assure that the water heater
is filled with water.
5. The water pump should stop running once all faucets are closed.
6. The water pump is now ready for automatic operation. The pump will run
when a faucet is open and stop when a faucet is closed.
Figure 11-6. Water
7. Never allow the pump to run for long periods of time without water being
Pump Switch
present in the supply tank, as doing so may cause physical damage or blow
fuses.
If water does not flow when a faucet is turned “on” while using the demand system, use the
following troubleshooting chart:
11-3
P L U M B I N G
&
B A T H
F E A T U R E S
Troubleshooting Chart of Automatic Demand Water System for No Water Flow
SITUATION
1.
2.
1.
2.
3.
4.
Pump running, but no water flow
Pump not running
SOLUTION
Fill Tank
Clear the water line to the pump
Check the pump switch
Check the 12-VDC fuses
Check the electrical connections
Check the battery
All of the water should be drained from the freshwater system when the unit is not in use for
extended periods. For more detailed information regarding the water pump, one should refer to the
water pump manufacturer’s brochure in your Zephyr Owner’s Information Package.
City Water Connection
When connecting your mobile home to an external source of city water, be certain to use the water
hose manufactured and labeled for potable water service--this will assure that
the hose selected for use will not alter the taste of the water. To connect the
city water supply to the motor home, connect one end of the power
retractable hose (Figure 11-7) to the city water supply; this connection will
usually be to a faucet or valve similar to your garden hose valve at home.
Turn the city water supply “on” (Figure 11-8) for a few seconds to clear the
line. Once the water hose has been
flushed thoroughly, turn the supply “off.”
Connect the other end of the hose to the
city-water connections on the motor
home.
Figure 11-8. City Water Valve
Figure 11-7. Power
Hose Reel
Once the city water fill valve is opened, water is supplied to the
freshwater system including the hot water heater, faucets, and
toilet. Turn “on” the water supply and open all of the faucets to
clear any trapped air within the plumbing lines within the motor
home.
Once any air pockets have purged from the water lines and water flows freely, close all of the
faucets. The city water supply is pressurized (usually 60-80 psig); therefore, the water pump is not
needed when the water system of the motor home is connected to the city water system.
To disconnect the motor home from the city water supply, close the valve and remove the hose
from the city water supply. Disconnect the hose from the city water connection, drain it, and store
the hose in the water compartment of the motor home.
11-4
P L U M B I N G
&
B A T H
F E A T U R E S
Filling the Freshwater Tank
The freshwater tank is normally filled from the city water connection. The city-water valve (Figure
11-8) located in sanitation compartment near the water connection determines whether the city
water is going through the motor-home water system or into the freshwater tank. Since there is not
an automatic shut-off when filling the freshwater tank, check the level from the monitor panel while
filling the freshwater tank on the motor home.
The excess water will be vented from an overflow in vent pipe onto the ground when the capacity of
that tank has been reached. This pipe is installed in the freshwater tank to prevent possible tank
rupture from inadvertent overfilling.
All of the water should be drained from the freshwater system when the motor home is not in use
for an extended period of time.
Sanitizing
To assure complete disinfecting of the freshwater system, it is recommended that the following
procedure be performed on a new system, on one that has not been used for a length of time, or
one that may have become contaminated. This procedure is also recommended before long periods
of storage, such as during the winter months:
1. Drain the freshwater tank by opening the drain valves. There is one valve for each water
tank. All of the faucets should be in the closed or “off” position.
2. Prepare a chlorine solution using one gallon of water and one-half cup of chlorine bleach
(5% sodium-hypochlorite solution). Prepare enough of the chlorine solution to administer
one gallon of solution for every 15 gallons of tank capacity. For sanitizing this tank, prepare
4½ gallons of the chlorine solution. This mixture puts a 50 ppm (parts per million) residual
chlorine concentration in the water system that will act as a quick-kill dosage for harmful
bacteria, viruses, and slime-forming organisms. Concentrations greater than 50 ppm may
damage the water lines and/or the tank.
3. Once the freshwater tank is empty, close the drain valves in the water tank.
4. Pump the chlorine solution into the tank by first placing the winterizing hose into the
chlorine solution. Close the valve from the fresh water tank to the pump and open the valve
from the solution to the pump. Turn the tank fill valve from “city water” to “tank fill.”
Turn “on” the water pump until all of the solution is pumped into the freshwater tank.
5. Turn “off” the water pump. Then close the valve to the solution. Open the valve from the
tank to the water pump. Fill the water tank with the city water tank fill (or by using the same
method as was used to put the sanitizing solution into the tank).
11-5
P L U M B I N G
&
B A T H
F E A T U R E S
6. Remove the water filter (located in the sanitation compartment outside the motor home) and
install the bypass pipe to allow the sanitizing solution access to the faucet. Open each
faucet, in turn, including the kitchen faucet, bath faucet, inside and outside showers, turning
“on” both the hot and cold faucets and flushing the toilet until all of the air has been purged
from the pipes and the water runs freely. The entire system will then be filled with the
sanitizing solution.
7. Allow the 50 ppm disinfecting solution to stand in the system at least four hours.
8. Drain the system and flush it with freshwater. The water system needs to be flushed with
water repeatedly, if necessary, until there is no chlorine taste or smell left in the system. To
remove any excessive chlorine taste or odor that might remain, prepare a solution of one
quart of vinegar to five gallons of water. “Rock” the tank containing the solution by moving
the motor home forward and backward several times to clean the tank; then drain that tank
and refill with clean water.
Water Filter
This motor home is equipped with a water filter (Figure 11-9) which must be
removed before disinfecting the freshwater system. First remove the water
filter and then install the by-pass pipe to allow the sanitizing solution access
to the drink dispenser faucet. The water filter is located in the sanitation
compartment on the outside of the motor home. The filter will remove
chlorine, dirt, and other matter.
The filter will also eliminate most phenol (or similar) odors and tastes while
delivering sparkling, taste-free water for drinking and cooking. The filter is
not guaranteed to remove the tastes and odors of iron and sulfur. To
remove these impurities, one would need to chlorinate the water.
Replacement filters are available that will filter iron and sulfur. Ask your
dealer or RV supply center about purchasing an iron and sulfur filter, if such
is desired.
Figure 11-9. Water
Filter
If you are traveling in an area where the water has a high iron and sulfur content, then add one
tablespoon of chlorine bleach to every 10 gallons of water in your tank--this will precipitate the iron
or sulfur so that the filter can remove those impurities. If you are at a site where the unit is
connected to a city water supply, you will not be able to chlorinate the system because the water
flows straight to your faucets and not through the freshwater tank. Filters should be changed every
6-12 months depending on the quality and quantity of water that is used in your motor home.
11-6
P L U M B I N G
&
B A T H
F E A T U R E S
Freshwater Lines
Vibration and flexing encountered when the motor home is traveling can cause pipes and fittings to
become loose. Check all of the plumbing connections for leaks at least on an annual basis. If the water
pump runs when all faucets are turned “off,” check for a possible leak. Be sure that the drain valves are
closed.
Connections at the kitchen and bathroom faucets normally seal by hand-tightening them and then making
an additional half-turn with a wrench. If a fitting leak persists, disconnect it completely and visually
inspect it for mineral deposits or foreign material stuck on the sealing surfaces. Clean the surfaces
thoroughly and reinstall the fitting. Take the motor home to an authorized Tiffin Motorhomes service
center for additional repairs if the water system continues to leak. Follow the winterizing instructions
given in Chapter 14 to reduce risk of leaks caused by cracks from freezing pipes. Left unchecked, freezing
damage can be extensive and expensive.
Plumbing Manifold
The plumbing manifold (Figures 11-11, 12) provides the convenience of allowing the water system to still
be operational in the event a water leak in any water outlet (e.g., lavatory, toilet) may occur. The plumbing
manifold allows the user to discontinue water to the
suspected leak source without disrupting the entire
water system.
Figure 11-11, 12. Plumbing
Manifold
WASTEWATER SYSTEMS
General Information
The waste drainage system was designed to provide adequate and safe storage and/or disposal of
waste materials. All of the materials used in the fabrication of this system are tested by a nationallyrecognized testing laboratory. The drainage system uses plastic piping and fittings connected to the
sinks, toilet, and holding tanks. This plumbing permits the drainage of these fixtures to an outside
termination.
The motor home should be reasonably level for best operation of both of the wastewater systems
(there are two, separate wastewater systems). The gray-water system is for wastewater from the
11-7
P L U M B I N G
&
B A T H
F E A T U R E S
sinks and shower. The black-water system is for sewage waste from the toilet. Each wastewater
tank has its own control valve and both drain through a common sewer-drain hose.
Toilet
The toilet (Figure 11-13) in your motor home is specifically designed for
recreational-vehicle service. The toilet operates with water from either
the fresh water tank with the water pump “on” or the city water supply.
Before using the toilet, add water to the bottom of the tank. Refer to the
“BLACK WATER TANK” instructions elsewhere in this chapter. The
toilet flushes waste directly into the black-water holding tank. The toilet
uses high-velocity water injection to produce swirl effect in the bowl.
The greatest problem that causes stool solids to accumulate in the
holding tank is lack of liquids. When using your toilet, it is important that
you use as much water as possible with each flush. This will help prevent
tissue and other solids from clogging the holding tank outlet.
Figure 11-13. Toilet
The toilet has a Mode switch that is located on the right side of the control module. It lets you
switch between three function settings: NORMAL, SERVICE, and MANUAL OVERRIDE.
Simplified instructions for electronic use of the toilet are as follows:
To Add Water: Raise the flush handle until desired water level is reached. Note: The water flow will
stop automatically after a pre-programmed period of time.
To Flush: Press the flush handle down. Water will flow into bowl for two seconds, and then flush
ball will open. The toilet will not flush again until the water refill cycle is complete.
The toilet features a Remote Flush Switch. Simply press the top part of the switch to add water to
the bowl. To flush, press the bottom part of the switch.
In the event of power or battery failure, you may flush the toilet manually. Using the MANUAL
OVERRIDE option on the Mode Switch will disconnect the electronic brake in the flush valve
motor, and allow manual flushing via the override access hole in the side of the vitreous china base.
Note: The control module allows 15 seconds of water flow for cleaning. If more water is required,
return the switch to the NORMAL position, and then back to the SERVICE position. For detailed
instructions on manual flushing, refer to the specific owner’s manual which will be located in the
Owner’s Information Package.
The toilet should be cleaned regularly for maximum sanitation and operational efficiency. Clean the
toilet bowl with a mild bathroom cleaner. DO NOT USE CHLORINE OR CAUSTIC
CHEMICALS, SUCH AS LAUNDRY BLEACH OR DRAIN-OPENING TYPES, AS
11-8
P L U M B I N G
&
B A T H
F E A T U R E S
THEY WILL DAMAGE THE SEALS IN THE TOILET AND DUMP VALVES. Refer to
the toilet-manufacturer’s owner’s manual in your Zephyr’s Owner’s Information Package for
complete instructions and a detailed troubleshooting guide.
Caution
It is important that you use as much water as possible with each flush. This will help
prevent tissue and other solids from clogging the holding tank outlet.
P-Traps
Each of the sink drains, the shower drain, and the washing-machine drain (if so equipped) has a water trap
(i.e., the p-trap) to prevent holding-tank odors from entering the motor home. These traps must have
water in them to trap odors. When the vehicle is in motion, the water may splash out of the sink and
shower drains.
When the motor home is stored, the water may evaporate from these traps allowing odors to enter
the motor home. If this occurs, run water from the faucet into the drain, thus allowing water to fill
the traps again. A good practice would be to run a little water into these drains on a monthly basis.
Black-Water Holding Tank
The “black water” (i.e., sewage) holding tank is located directly beneath the toilet. Before using the toilet,
you will need to treat the tank with water that is mixed with an odor-controlling chemical. Be careful not
to spill the chemicals on your hands, clothing, or the carpet because such may cause a permanent stain.
Pull the toilet levers forward to allow the chemicals to mix with the toilet water. Continue pulling the
toilet levers until a depth of at least one inch of solution is directly under the toilet. Release the levers and
the waste tank is now ready for use.
Caution
Use only approved RV odor-controlling chemicals in the holding tanks. Products
containing ammonia and petroleum will damage the ABS plastic holding tanks and
seals.
11-9
P L U M B I N G
&
B A T H
F E A T U R E S
Gray-Water Holding Tank
The gray-water holding tank is located in the underbelly of the vehicle. It is primarily used for the
drainage from the kitchen and bath sinks and the shower.
Wastewater Disposal
Both of the holding tanks terminate in
a valve arrangement that permits
draining each tank separately or
together (Figure 11-14).
It is
recommended to drain the black-water
tank first before draining the graywater tank. This procedure permits the
water from the gray tank to wash the
black-water residue from the drain
lines and hose. The valves that open to
release the water are called gate valves.
The blade that closed the opening in
the sewer drainpipes is connected to
Figure 11-14. Sanitation Compartment Containing Holding Tank Drains and
the T-handle to release contents of
Flexible Drain Hose
the tank(s) when pulled. The sewer
line must be securely capped during self-containment use to prevent leakage of waste materials onto the
ground or pavement. Do not pull the holding tank gate valve “open” when the protective cap is installed
on the pipe. Always drain the tank into an acceptable sewer inlet or dump station.
Whenever possible, drain both the holding tanks prior to traveling. The carrying capacity of your
vehicle will be reduced if water (at 8.3 pounds/gallon) is left in the black or gray tanks.
The holding tanks should only be drained when they are at least ¾ full. Doing this will provide a
sufficient volume of water to allow the
complete flushing of waste materials in the
drain lines and hose. If the tanks are not
¾ full, add enough water to allow for
sufficient flushing.
To empty the wastewater tanks, connect
the adapter, supplied with your vehicle, to
the drain hose (Figure 11-15). If the
adapter is lost or broken, another one can
readily be purchased from any RV supply
store. Once you have placed the adapter
on the drain hose, it can remain there for
Figure 11-15. Sewer Hose and Drain Connections
11-10
P L U M B I N G
&
B A T H
F E A T U R E S
the life of the hose. One end of the hose threads up through the hole in the bottom of the service
compartment and the other end of the hose feeds into the sewer at the dump station.
Unscrew the cap from the drain. Connect the hose, with the adapter in place, to the drain fitting.
Open the gate valve completely by pulling on the T-handle. The tank will start to drain as soon as
the T-handle is pulled. After you have drained the black-water tank, immediately drain the graywater tank. This procedure helps to flush the black water from the sewage hose.
When both of the tanks are empty, flush them with a freshwater rinse before you close the valves.
The gray tanks are easily flushed by pouring a couple of gallons of water into a sink drain. The drain
outlet is engineered for quick release of the drain hose adapter. Always close the gate valves and
secure the end cap to prevent leakage while the vehicle is in transit.
After draining the black-water tank, it is recommended to add a holding-tank deodorant to help
control the odor and break down the solids. Follow the instructions given on the holding-tank
deodorant package.
When using dump stations for draining the holding tanks, keep other travelers in mind. Please practice
good housekeeping! Leave the dump stations in good order. Above all, do not pollute!
Sewer Connection and Camping
When camping at parks with sewer connections, it is important to keep the black-water, holding-tank, gate
valve closed at all times, except when dumping. The gray tank can be kept open while hooked to a sewer
connection, but again, the black-water tank must be kept closed. This is done so that an ample quantity of
liquid remains in the black-water tank to provide a smooth flow through the gate and drain valves when
dumping.
Caution
The gray tank valve must be in the “open” position when operating the washing
machine.
Sufficient liquid in the black-water tank causes a swirling action that should take any accumulated
solid wastes with it. Accumulation of solid wastes in the black-water tank can be avoided by keeping
the gate valve closed when connected to the sewer connection. If the valve is open, solid wastes
may accumulate in the tank which may eventually result in costly repairs.
11-11
P L U M B I N G
&
B A T H
F E A T U R E S
No-Fuss Flush
This vehicle may be equipped with a flushing system for the black-water holding tank. When
draining your sewer tank, attach a water hose to the sewer spray connection. After the tank is
drained, leave the gate valve “open” and open the water valve to allow water to spray inside the
black-water tank; this will clean the inside of the tank of any debris that may be left inside the tank.
After this is done, disconnect the freshwater hose and close the gate valve.
Caution
Be sure the gate valve is “open” when flushing the tank. Do not use the same hose
for the No Fuss Flush that is used for filling the fresh water tank.
Exterior Shower
Your Zephyr has an exterior shower (Figure 11-16, left-hand side) for your use and convenience
outside. That exterior shower is located in the
sanitation service compartment, which is located on
the driver’s side of the motor home. The exterior
shower feature allows you to do such things as rinse
off sand or grass, muddy shoes, or bathe yourself
outside of your motor home.
The faucet operates just as it would in your kitchen or
bathroom. In addition to the shower itself, there is
also a soap dispenser conveniently situated in that
same compartment and a light to permit use under
low-light conditions.
11-12
Figure 11-16. Exterior Shower in Outside Compartment
P L U M B I N G
&
B A T H
11-13
F I X T U R E S
C O N S T R U C T I O N
F E A T U R E S
Chapter
12
Construction Features
12-1
C O N S T R U C T I O N
F E A T U R E S
Construction Notes
Your Zephyr manufactured by Tiffin Motorhomes is constructed of the finest materials available by well
experienced craftsmen at the Tiffin Motorhomes manufacturing facilities in Red Bay, AL. Every care and
concern have been taken throughout the total manufacturing process to assure you of the finest motor home
available in the marketplace today. To give you a better appreciation of the features of the Zephyr motor
home, some of its construction features are now presented.
The Zephyr is built on a Spartan chassis (Figure 12-1) powered by a Cummins
diesel engine. The floor decking is constructed of ½” OSB board to provide
desired rigidity and firmness in the floor of the motor home. The floor is
insulated with block foam to provide both thermal insulation and sound
deadening to keep road-surface noises from unduly entering the motor home.
Figure 12-1. Spartan Chassis
The motor-home roof is also insulated with block foam to provide an
adequate barrier to heat loss or gain through the roof.
In the Zephyr, each sidewall is manufactured to provide essential
strength and durability and is also insulated to assure the comfort of the
enclosed spaces. Sidewalls are constructed of aluminum or steel framing,
insulated with 1½”-thick block foam insulation. Framing and insulation
are laminated between interior décor board and gelcoat fiberglass on the
exterior to provide superior strength and rigidity. The insulation is
chosen to both provide a sound-deadening barrier from outside noises
and to provide more effective thermal control of the enclosed cabin in
the motor home, thus allowing greater efficiency of the heating and airconditioning systems, depending on the environment sought.
Typical Floor Plan
A typical floor plan is presented to show the relative components of the
Zephyr.
12-2
W I N D O W S ,
A W N I N G S ,
V E N T S ,
&
D O O R S
Chapter
13
Windows, Awnings, Vents, & Doors
13-1
W I N D O W S ,
A W N I N G S ,
V E N T S ,
&
D O O R S
Windows
The windows on the Zephyr are of the sliding type. These double-pane windows also provide additional
thermal control (i.e., insulation) to maintain interior temperatures better. In the double-pane windows, a “dead
air” space (filled with a dry, inert gas) is sealed between the two panes of
glass—this “dead air” space provides additional thermal insulation for the
windows and prevents them from fogging internally. Additionally, there
may be a reflective coating on the windows to reflect back a portion of the
sunlight to reduce the heating of the motor-home interior and to reduce the
effects of the sun’s “bleaching” of interior fabrics (curtains, upholstery).
For both the driver’s and the passenger’s windows, additional sun shades
are available to permit blockage of the sun’s rays which may interfere with
driving. These shades can be deployed, as needed, and then moved out of
the way when no longer desired.
Figure 13-1. Typical Window
In the bedroom, one particular
window will be marked with an “EXIT” label—this is an
emergency escape (Figure 13-2) to be used only when normal exits
are blocked or inaccessible. To use this emergency escape, merely
lift the red handles at the bottom of the window and push outwards
to open the window. Should it be necessary to use this exit, please
look for a secure footing when exiting so that no personal injury is
sustained in the process. It is also prudent, when parking the motor
Figure 13-2. Emergency Exit Window
home, to be aware of where this “emergency-exit” window will be
situated so that it is not inadvertently blocked or impeded from its
normal, intended operation, should such become necessary.
Awnings
Your Zephyr may be equipped with a power patio awning and controller (Figure 13-3). If so, use the following
directions to operate the awning properly: NOTE: You may first have to program the key fob which can
remotely activate the awning; please consult the owner’s manual for the
power awning for directions on the programming process.
Extending the Awning:
1. First, examine the area where the awning is to be deployed and
make sure that there are no obstructions that may impede the
opening of the awning.
2. Make sure that the weather conditions warrant opening the awning;
for example, the wind isn’t too blustery or no major storm fronts
are soon to be expected in the immediate area.
13-2
Figure 13-3. Dometic Awning Control
Box
W I N D O W S ,
A W N I N G S ,
V E N T S ,
&
D O O R S
3. One can either use the control box (Figure 13-3) or the key fob (Figure 13-4) to deploy the awning.
For the control box, press the rocker switch upwards to extend the awning; for
the key fob, press the “extend” button on the key fob—either action will cause
the awning to deploy to its fully extended position. If there is a remote switch
inside the motor home, one can activate the awning from inside the motor
home by pressing the rocker switch upwards to the “extend” position.
NOTE: If one wishes to protect the awning automatically from possible windy
conditions which may damage the awning, set the wind sensor switch on the
console to the “on” (usually upper) position. To disable this function, set the
wind sensor switch to the “off” (usually down) position.
Figure 13-4. Dometic
Awning Key Fob
Controller
Caution
Since damage resulting from weather is not under warranty, anytime a heavy or
prolonged rain or blustery winds are anticipated, it would be advisable to retract the
awning. Similarly, if the awning is to be left unattended for any prolonged length of
time, it would be prudent to retract that awning.
Retracting the Awning:
1. Make sure that nothing (e.g., nearby tree, patio torches) obstructs the intended movement of the
awning.
2. One can either use the control box or the key fob to retract the awning (Figure 13-5). For the control
box, press the rocker switch downwards to retract the awning;
for the key fob, press the “retract” button on the key fob—
either action will cause the awning to retract to its fully closed
position. If there is a remote switch inside the motor home, one
can retract the awning from inside the motor home by pressing
that rocker switch downwards to the “retract” position.
NOTE: If one wishes to protect the awning automatically from
possible windy conditions which may damage the awning, set the
wind sensor switch on the console to the “on” (usually upper)
position. To disable this function, set the wind sensor switch to
the “off” (usually down) position.
13-3
Figure 13-5. Awning (Fully Retracted)
W I N D O W S ,
A W N I N G S ,
V E N T S ,
&
D O O R S
Emergency Retracting Procedure for the Awning:
If the automatic retracting of the awning isn’t possible, one may manually close the awning using the following
procedure:
1. Slide the pull strap (provided) into the utility slot of the Fabric, Roller Tube, Torsion Assembly (FRTA)
[see the Weather Pro Power Awning Diagnostic Service Manual {Dometic Corporation} for
illustration].
2. While one person holds the pull strap, remove the bolt in the top of the right top casting (see picture in
the awning owner’s manual for details). The FRTA will retract (i.e., “roll in”) once the bolt is removed.
Walk the awning to its retracted position (i.e., fully closed).
3. When the awning is fully retracted, replace the bolt to prevent the awning from accidentally opening
during travel. NOTE: After this procedure has been performed, have the awning serviced by a
Dometic Service Center or a qualified service technician before any further attempts are made to open
the awning.
Vents
The kitchen has a 12-VDC Fantastic vent fan (Figure 13-6) installed to exhaust
kitchen odors. For normal operation, the vent is controlled by a thermostat
mounted on the vent. Once the vent power switch is in the “on” position and
the thermostat is set to a particular temperature, the vent fan will operate until
the temperature set-point is reached; at which time the vent fan will
automatically turn “off.”
The vent fan should only be left in the “on” mode when the motor home is
parked and in use.
If the motor home is to be unattended for long periods of time or is to be in
Figure 13-6. 12 VDC Vent Fan
storage, make sure that the vent fan is turned “off.” Were the fan left “on,”
blustery winds or severe storms may prevent the vent from closing and, consequently, may permit leakage, with
possible damage, into the motor home. The bathroom also contains a 12-VDC, vent fan which is controlled by
an “on/off” switch mounted on the bathroom wall.
Doors
Caution
Always secure the dead bolt lock while the motor home is in motion to prevent
accidental opening of the entrance door.
13-4
W I N D O W S ,
A W N I N G S ,
V E N T S ,
&
D O O R S
The primary entrance door (Figure 13-7) to the motor home is a radius door having a key lock and a dead bolt
for additional security. When the door is fully opened, the
door hinge automatically holds the door in an “open”
position. To close the door from this “open” position,
either the inside or outside handle must be released to
permit the door to move; then the door may be closed and
then locked, if desired.
There is also a screen door (Figure 13-8) associated with the
entrance door; the screen door will permit increased air
circulation when the entrance door is open. To enjoy this
benefit, the screen door is operated independently of the
entrance door.
Figure 13-8. Front
Door & Screen Door
However, when one wishes to close the screen door and the
entrance door at the same time; the screen door latch must be
fastened to the entrance door prior to closing the entrance door. Failure to do so will cause the screen door
latch to be bent.
Figure 13-8. Front
Door
Keyless Lock
The Zephyr will be equipped with keyless lock entry that is incorporated into the grab handle. The keyless lock
entry is essentially a numeric combination lock (Figure 13-9, lower left-hand side).
This type of lock for the motor home permits the owner to come and go without having
to worry about whether the “house key” was with the owner or not. The keyless lock
drastically reduces the inadvertent situation of being “locked out of one’s home” while
on the road.
As long as one remembers the appropriate combination (settable by the owner to permit
optimal remembering of a preferred numerical combination—see Figure 13-10), one
should never be “locked out” of the motor home under any circumstances.
Figure 13-9. Keyless
Lock and Grab
Handle
Complete directions for setting one’s unique keyless lock combination can be had in
the Owner’s Information Package.
As a further aid for night-time access to the motor home, the hand rail by the front
door is made of a transparent acrylic which is lighted at night.
This “night light” hand rail permits the motor home owner easy and safe access to the
motor home by providing a firm, easily seen handhold whenever one is entering or
exiting.
Figure 13-10. Detail of Keyless Lock
13-5
R O U T I N E
M A I N T E N A N C E
Chapter
14
Routine Maintenance
14-1
R O U T I N E
M A I N T E N A N C E
EXTERIOR CARE
Important
Damage caused by improperly performed maintenance or inadequate maintenance
is not covered by your Tiffin Motorhomes Limited Warranty.
Washing
The exterior (Figure 14-1) of your new motor home is made of prefinished fiberglass. Frequent washings and thorough cleanings are
required to prevent damage to the motor-home finish after exposure
caused by damaging salts, calcium chloride, road tar, tree sap, insects,
and other foreign material. Damage caused by exposure to these
items is not covered by your warranty agreement.
Never wash the motor home in direct sunlight, while the motor
home is hot, or with hot water. Any accumulation of mud and dirt
Figure 14-1. Zephyr Exterior
under the body can cause damaging rust on steel parts. Corrosive
materials, such as those used for ice and snow removal and dust control, also can accumulate on the
underside of the motor home.
These accumulations, especially in vehicular areas where mud and other foreign materials could
collect, should be removed by flushing those areas (e.g., the underside) of the motor home regularly
with water. The chance of corrosion can be minimized with frequent washings of the motor home.
When washing the motor home, make certain that the undercarriage and the wheel wells are
thoroughly cleaned, as well as the exterior of the motor home. Do not use strong soaps or
detergents for washing the motor home. Always use a mild soap in warm water, a commerciallyprepared product for automotive finishes, or your local car wash to wash your motor home
properly.
Be careful when using any pressurized washer to avoid loosening any exterior decals or sealants and
the like. After washing, carefully inspect the caulking around the window frames and vents and any
other joints to see if any seal separations have occurred. Should any re-caulking be necessary, it is
relatively simple and is considered to be routine maintenance which is the responsibility of the
owner.
14-2
R O U T I N E
M A I N T E N A N C E
Important
Never use a strong solvent, such as lacquer thinner or harsh abrasives, on any of
the exterior painted surfaces.
Waxing
The exterior finish will require a routine waxing. When water will not bead and roll off a freshly
washed motor home, a new coat of wax is needed. Wax not only improves the appearance of the
motor home, but it also protects the finish against oxidation and corrosive materials.
The recommended type of wax is one that is compatible with painted and gel-coated fiberglass
finishes and contains an UV (ultra-violet) inhibitor. Buffing with a polishing compound will
improve a dull or discolored finish.
Important
When using a polishing compound that does not contain a wax preservative,
reapplying a coat of hard wax after polishing is recommended.
Seals
The seals (Figure 14-2) around the doors, windows, vents, slide-out trim
and external seams should be checked at least semi-annually.
Additionally, the roof seams should be inspected for cracking or peeling
annually. If deterioration is noted during a routine-maintenance
inspection, reseal the seams or seals with an approved sealant to prevent
leaks.
Figure 14-2. Typical Seals on
Zephyr
Your Tiffin Motorhomes dealer can perform the resealing inspections and
subsequent work, if any, for you. It is recommended that a Tiffin Motorhomes authorized service center
perform these inspections periodically and perform necessary resealing when necessary.
14-3
R O U T I N E
M A I N T E N A N C E
Proper Sealants for Application
The following sealants are recommended for specific sealing applications, as noted in the table:
Recommended Sealants for Specific Sealing Applications
SEALANT
APPLICATION
Plas-T-Cote
Surebond #SB-140
Carlisle #502-LSW Self-Leveling Sealant
Silicone Sealant
Parbond
Metal or fiberglass roof
Rubber laminated to metal roof and ALL SKYLIGHTS
Rubber roof over wood base
To cover butyl and other sealants; not to be used as the
main sealant
To seal across tops of windows and the like on exterior
surfaces where silicone is not used
Striping and Decals
The striping and decals (Figures 14-3,4) on your motor home normally require very little
maintenance. Treat these as you would any painted surface on your
motor home. Wash them with mild soap
and warm water or any retail car soap.
Never wash the motor home in direct
sunlight, while the motor home is hot, or
with hot water. Rinse very thoroughly to
remove or prevent any undue accumulation
of any soap residues.
Figure 14-3.
Exterior Detailing of Zephyr
Use caution with high-pressure wash nozzles. Keep such nozzles at
least 18 inches from the edge of the decals during any washing
operations. If this is not followed, high-pressure water nozzles may
cause the decals to loosen and subsequently to peel.
Figure 14-4. Rear View of
Zephyr
Test small sections of decals when using any type of cleaning
solution.
14-4
R O U T I N E
M A I N T E N A N C E
Important
Do not use solvents such as acetone, MEK, toluene, and the like on the decals. Any
solvent including alcohol may soften and smear colors. Do not use lacquer thinner
or paint thinner on decals. Do not overcoat the decals with clear paint. Do not
allow gasoline or other fuels to come into prolonged contact with the decals.
However, if this should occur, immediately flush the affected area with water.
Alcoa Aluminum Wheel Care
The care and maintenance of your aluminum wheel products are simple and require no special
material or products; simply follow the directions included in the Owner’s Information Package for
these aluminum wheels. Timely care and cleaning will maintain the appearance of these wheel
products for many years.
Important
Do not use harsh detergents, acids, or abrasives which may scratch or dull the
surfaces. The applicator cloth, sponge, or soft-bristled brush should be nonmetallic and non-abrasive.
Important
Remember to check periodically the tightness of your wheel lug nuts.
Roof Care and Maintenance
Proper care and maintenance of your motor home, including your roof, is important for sustained,
trouble-free performance. Normal maintenance is simple and easy and does not require special
materials. The roof of the motor home is fiberglass and can be cared for in the conventional
manner. Keep the roof clean; one should clean the roof at least every three months. The roof
14-5
R O U T I N E
M A I N T E N A N C E
should be professionally inspected on an annual basis for leaks. Sealant may be necessary in the
second year of ownership.
Warning
Use caution when working on the top of your motor home. The wet roof may be
extremely slippery and, as such, a possible safety hazard.
Moisture Management
This section outlines important recommendations to manage moisture in your motor home to avoid
moisture-related damage, such as mold, which is caused by moisture. The materials and methods used to
construct your motor home were selected in part to minimize air leakage and to create a weather tight
exterior shell. However, in order to protect your investment and reduce the risk of moisture-related
damage and costly repairs, attention and care has to be taken to manage moisture inside your RV. Note:
These are only suggestions intended to minimize moisture-related issues with your motor home. If any
concerns arise, contact Tiffin Motorhomes’ Service Department at (256) 356-0261.
Interior Care of Your RV
Signs of excessive moisture can be obvious, such as water droplets forming on surfaces or wet carpet.
Conversely, signs of excess moisture can be subtle, such as condensation forming on metal surfaces.
When symptoms appear it is important to timely determine the cause of the excess moisture and take
appropriate corrective action to prevent moisture related damage.
Control Relative Humidity
Monitoring and controlling relative humidity within the motor home is one of the most important steps
to minimize the risk for moisture-related damage. Ideally, relative humidity
should be at 60% or less. Relative humidity can be monitored utilizing a portable
hygrometer (Figure 14-5), a small device that measures temperature and relative
humidity. Hygrometers are available at electronics or building supply stores. Use
exhaust fans, the air conditioner, and/or a portable dehumidifier to manage
moisture inside the RV to maintain relative humidity at 60% or less. In cold
climates, relative humidity may need to be at 35% or less to avoid window
condensation issues. If the motor home is used the majority of the time in a hothumid climate, it may be difficult to keep relative humidity below 60%. A
dehumidifier will help, but is important to check the condensation (water)
collection bucket regularly or discharge the condensation (water) directly to a
Figure 14-5. Portable
Hygrometer
14-6
R O U T I N E
M A I N T E N A N C E
drain.
Avoid Drastic Thermostat Setbacks
Cooler surface temperatures increase the potential for condensation and surface mold growth. To
minimize the opportunity for condensation to form on interior surfaces, maintain a comfortable
temperature in your RV, and avoid nighttime setbacks of 10 degrees or more. Drastic setbacks that reduce
the indoor air temperature quickly can increase the chance for airborne moisture to condense on cool
surfaces such as windows. If you are away from your RV for an extended number of days, it is
recommended that you do not set the temperature back without taking other measures to manage relative
humidity, including operating a dehumidifier with a continuous drain.
Manage Window Condensation
Window condensation issues can be identified by water or ice-build up, usually at the base of the window.
The majority of these problems can be addressed by managing moisture generated inside the motor
home. Minor condensation issues are not unusual, especially for RVs used in colder climates. The key is to
manage this small amount of moisture if evident by wiping the surface, and as discussed in the “Control
Relative Humidity” section, maintaining a reasonable relative humidity within the unit. To help minimize
window condensation, use exhaust fans vented to the outside, avoid drastic changes in thermostat
settings, do not use “vent-free” heaters and use window coverings wisely. For example, make sure to open
curtains or blinds during the day to allow air to circulate and warm the window surface.
Carpet Care and Moisture Management
To keep your carpet serviceable and looking new for years to come, the carpet should be cleaned when it
shows signs of discoloration or traffic patterns. A steam cleaning system should be used to clean the
carpet unless other noted in your warranty information. To manage moisture from the cleaning process,
the cleaning system needs to be capable of extracting the excess water from the carpet after it has been
cleaned. Important: Be sure the carpet is thoroughly dry before closing up the RV for storage. Water
from the cleaning process can cause significant damage to the RV if the carpet is not completely dry
before closing up the motor home for an extended period.
Cleaning Tile and Wood Floors
Most floors only require a mild detergent and warm water for cleaning. More water on the floor is not
always better for cleaning. Use a damp cloth to clean on a regular basis rather than wet mopping each
time. For more information regarding the maintenance of the tile and wood floors, see the section
entitled, “Woodwork and Floors.”
Storage and Other Isolated Areas within the RV
Storage areas are more difficult to condition since the areas are isolated from the main body of the RV.
The surfaces of these areas are more at risk for condensation and surface mold growth. To minimize this
risk, clean storage areas regularly, and allow an air space between stored items and the exterior wall to
promote air circulation.
14-7
R O U T I N E
M A I N T E N A N C E
Use of Un-Vented Combustion Equipment
Un-vented combustion equipment, such as propane stovetops are a source of moisture within the RV.
For every gallon of fuel consumed, approximately one gallon of water vapor is evaporated into the air.
Whenever possible, operate an exhaust fan in combination with the use of any un-vented combustion
appliance within the RV. Water vapor and other combustion byproducts should be vented to the exterior
of the RV. The RV owner should strictly follow use and maintenance instructions for safe operation of
any combustion equipment, particularly un-vented equipment.
Exterior Care of Your RV
The exterior shell of the RV is the primary weather and moisture barrier. Over
the life of the vehicle, the shell will require regular care and maintenance in
accordance with other instructions for exterior care. The shell includes the roof,
sidewalls, windows, doors, and under-floor of the vehicle. Particular attention
needs to be devoted to ensure these components are maintained to ensure a tight
barrier against bulk water intrusion. The shell should be inspected
Figure 14-6. Inspecting Slide
periodically for tears, gaps, and condition of sealants in accordance with this
Out Gasket
owner’s manual. Areas that require maintenance should be resealed utilizing
a similar, high quality sealant used by the manufacturer. Particular attention should be devoted to ensure
the slide outs are functioning properly. Each time a slide out is used it should be inspected to ensure
proper operation and sealing (Figure 14-6). The slide out gaskets should also be inspected to ensure
proper sealing when the slide out is operated.
Use of Your RV
It is important to remember that the square footage of an RV is significantly less than that of a single
family residence. This fact alone will elevate the relative humidity because there is less volume of air to
help absorb or dissipate the humidity. For example, showering and cooking create a lot of humidity in a
small area. In these instances, use of an exhaust fan and opening windows should reduce the relative
humidity, particularly when living in the RV for an extended period.
Severe Environments
Prolonged use of your RV in severe environments—for example in extremely cold or hot-humid climates,
will require extra care and maintenance to avoid moisture-related issues. In both extremely cold and hothumid climates more attention needs to be focused on controlling relative humidity within the RV. It also
may require the use of a portable dehumidifier to manage relativity humidity within an acceptable range.
This is discussed further in the “Interior Care of Your RV” section. If you have any questions about
moisture-related issues in the environment you plan to use the RV in for a majority of the time, contact
Tiffin Motorhomes’ Service Department at (256) 356-0261.
14-8
R O U T I N E
M A I N T E N A N C E
Storage of Your RV
During those periods when your motor home is not in use, care must be taken to ensure moisture sources
are addressed. Ideal storage of your RV would be in an enclosed climate controlled environment. When
this is not possible, the following steps should be taken to ensure moisture is controlled:
•
Turn off all water sources
•
Turn off all combustion appliances
•
Drain the water tank(s)
•
Drain the water heater
•
Open all closets, cabinet doors and drawers
•
Close all windows and entrance doors
•
Open a vent or a window enough to allow for some limited ventilation air flow, but not so far as
to allow snow or rain to enter
•
When storing the RV in high humidity climates (ambient relative humidity is greater than 60%
year round), add a dehumidifier drained to exterior to control humidity inside the RV during
storage
•
Refer to other sections of this owner’s manual for additional recommendations
Modifications to your RV
Consult Tiffin Motorhomes for guidance prior to making any modifications to your RV. It is important
that changes be completed by a qualified service firm to ensure moisture intrusion or accumulation
problems do not occur.
Wet Areas
Areas that are exposed to water spills or leaks should be dried as soon as possible and definitely within 2448 hours. Drying areas quickly minimizes the chance for moisture damage and possible mold growth,
which can begin to form colonies within 48 hours. A variety of methods can be used to help the drying
process:
•
Remove excess water with an extraction vacuum
•
Use a dehumidifier to aid drying
•
Use portable fans to move air across the surface
14-9
R O U T I N E
M A I N T E N A N C E
•
Because moisture is key to mold issues, treat all signs of condensation and spills seriously and deal
with promptly. Failure to deal with a moisture issue promptly may cause more severe issues where
none initially existed, or may make a small problem much worse.
•
Learn to recognize signs of mold—don’t paint over or cover up suspicious discoloration until you
are sure it is not mold. The affected surface must first be cleaned and dried; residual staining may
be painted.
•
Be sure to understand and eliminate the source of moisture accumulation as a part of the cleanup. Otherwise, the same issues will simply reoccur.
•
Small amounts of mold should be cleaned as soon as it appears. Small areas of mold should be
cleaned using a detergent/soapy solution or an appropriate RV household cleaner. Gloves should
be worn during cleaning. The cleaned area should then be thoroughly dried. Dispose of any
sponges or rags used to clean mold.
Tire and Tire Safety Information
This portion of the Owner’s Manual contains tire safety information as required by 49 CFR 575.6. The
National Traffic Safety Administration (NHTSA) can be contacted at 1-888-327-4236. Their web site is:
http://www.safecar.gov and their address is: NHTSA, 400 Seventh St, S.W., Washington, D.C. 20590.
Section One:
The National Traffic Safety (NHTSA) has published a brochure (DOT HS 809 361) that discusses all
aspects of Tire Safety, as required by CFR 575.6. This brochure is reproduced in part below. It can be
obtained and downloaded from NHTSA, free of charge, from the following web site:
http://www.nhtsa.dot.gov/cars/rules/TireSafety/ridesonit/tires index.html
Studies of tire safety show that maintaining proper tire pressure, observing tire and vehicle load limits (not
carrying more weight in your vehicle than your tires or vehicle can safely handle), avoiding road hazards,
and inspecting tires for cuts, slashes, and other irregularities are the most important things you can do to
avoid tire failure, such as tread separation or blowout and flat tires. These actions, along with other care
and maintenance activities, can also:
•
Improve vehicle handling
•
Help protect you and others from avoidable breakdowns and accidents
•
Improve fuel economy
•
Increase the life of your tires
14-10
R O U T I N E
M A I N T E N A N C E
This section presents a comprehensive overview of tire safety, including information on the following
topics:
•
Basic tire maintenance
•
Uniform Tire Quality Grading System
•
Fundamental characteristics of tires
•
Tire safety tips
Use this information to make tire safety a regular part of your vehicle maintenance routine. Recognize that
the time you spend is minimal compared with the inconvenience and safety consequences of a flat tire or
other tire failure.
Safety First-Basic Tire Maintenance
Properly maintained tires improve the steering, stopping, traction, and load-carrying capability of your
vehicle. Under-inflated tires and overloaded vehicles are a major cause of tire failure. Therefore, as
mentioned above, to avoid flat tires and other types of tire failure, you should maintain proper tire
pressure, observe tire and vehicle load limits, avoid road hazards, and regularly inspect your tires.
Finding Your Vehicle’s Recommended Tire Pressure and Load Limits
Tire information placards and vehicle certification labels contain information on tires and load limits.
These labels indicate the vehicle manufacturer’s information including:
•
Recommended tire size
•
Recommended tire inflation pressure
•
Vehicle capacity weight (VCW—the maximum occupant and cargo weight a vehicle is designed
to carry)
•
Front and rear gross axle weight ratings (GAWR—the maximum weight the axle systems are
designed to carry)
For motor homes: Both placards and certification labels are permanently attached to the vehicle door
edge, door post, or glove-box door. You can also find the recommended tire pressure and load limit for
your vehicle in the vehicle owner’s manual.
Understanding Tire Pressure and Load Limits
Tire inflation pressure is the level of air in the tire that provides it with load-carrying capacity and affects
the overall performance of the vehicle. The tire inflation pressure is a number that indicates the amount of
air pressure—measured in pounds per square inch (psi)—a tire requires to be properly inflated. (You will
14-11
R O U T I N E
M A I N T E N A N C E
also find this number on the vehicle information placard expressed in kilopascals (kPa), which is the
metric measure used internationally).
Vehicle manufacturers determine this number based on the vehicle’s design load limit, that is, the greatest
amount of weight a vehicle can safely carry and the vehicle’s tire size. The proper tire pressure for your
vehicle is referred to as the “recommended cold inflation pressure.” (As you will read below, it is difficult
to obtain the recommended tire pressure if your tires are not cold.)
Because tires are designed to be used on more than one type of vehicle, tire manufacturers list the
“maximum permissible inflation pressure” on the tire sidewall. This number is the greatest amount of air
pressure that should ever be put in the tire under normal driving conditions.
Checking Tire Pressure
It is important to check your vehicle’s tire pressure at least once a month for the following reasons:
•
Most tires may naturally lose air over time
•
Tires can lose air suddenly if you drive over a pothole or other object or if you strike the curb
when parking
•
With radial tires, it is usually not possible to determine under-inflation by visual inspection
For convenience, purchase a tire pressure gauge to keep in your vehicle. Gauges can be purchased at tire
dealerships, auto supply stores, and other retail outlets.
The recommended tire inflation pressure that vehicle manufacturers provide reflects the proper psi when
a tire is cold. The term cold does not relate to the outside temperature. Rather, a cold tire is one that has
not been driven on for at least three hours. When you drive, your tires get warmer, causing the air pressure
within them to increase. Therefore, to get an accurate tire pressure reading, you must measure tire
pressure when the tires are cold or compensate for the extra pressure in warm tires.
Steps for Maintaining Proper Tire Pressure
•
Step 1: Locate the recommended tire pressure on the vehicle’s tire information placard,
certification label, or in the owner’s manual
•
Step 2: Record the tire pressure of all tires
•
Step 3: If the tire pressure is too high in any of the tires, slowly release air by gently pressing on
the tire valve stem with the edge of your tire gauge until you get to the correct pressure
•
Step 4: If the tire pressure is too low, note the difference between the measured tire pressure and
correct tire pressure. These “missing” pounds of pressure are what you will need to add
14-12
R O U T I N E
M A I N T E N A N C E
•
Step 5: At a service station, add the missing pounds of air pressure to each tire that is underinflated
•
Step 6: Check all the tires to make sure they have the same air pressure (except in cases in which
the front and rear tires are supposed to have different amounts of pressure)
If you have been driving your vehicle and think that a tire is under-inflated, fill it to the recommended
cold inflation pressure indicated on your vehicle’s tire information placard of certification label. While
your tire may still be slightly under-inflated due to the extra pounds of pressure in the warm tire, it is safer
to drive with air pressure that is slightly lower than the vehicle manufacturer’s recommended cold inflation
pressure than to drive with a significantly under-inflated tire. Since this is a temporary fix, don’t forge tot
recheck and adjust the tire’s pressure when you can obtain a cold reading.
Tire Size
To maintain tire safety, purchase new tires that are the same size as the vehicle’s original tires or another
size recommended by the manufacturer. Look at the tire information placard, the owner’s manual, or the
sidewall of the tire you are replacing to find this information. If you have any doubt about the correct size
to choose, consult with the tire dealer.
Tire Tread
The tire tread provides the gripping action and traction that prevent your vehicle from slipping or sliding,
especially when the road is wet or icy. In general, tires are not safe and should be replaced when the tread
is worn down to 1/16 of an inch. Tires have built-in tread-wear indicators that let you know when it is
time to replace your tires. These indicators are raised sections spaced intermittently in the bottom of the
tread grooves. When they appear “even” with the outside of the tread, it is time to replace your tires.
Another method for checking tread depth is to place a penny in the tread with Lincoln’s head upside
down and facing you. If you can see the top of Lincoln’s head, you are ready for new tires.
Tire Balance and Wheel Alignment
To avoid vibration or shaking of the vehicle when a tire rotates, the tire must be properly balanced. This
balance is achieved by positioning weights on the wheel to counterbalance heavy spots on the wheel-andtire assembly. A wheel alignment adjusts the angles of the wheels so that they are positioned correctly
relative to the vehicle’s frame. This adjustment maximizes the life of your tires. These adjustments require
special equipment and should be performed by a qualified technician.
Tire Rotation
Rotating tires from front to back and from side to side can reduce irregular wear (for vehicles that have
tires that are all the same size). Look in your owner’s manual for information on how frequently the tires
on your vehicle should be rotated and the best pattern for rotation.
14-13
R O U T I N E
M A I N T E N A N C E
A Tire Rotation Example
For maximum mileage, rotate your tires every 5,000 miles. Follow correct rotation patterns.
Tire Repair
The proper repair of a punctured tire requires a plug for the hole and a patch for the area inside the tire
surrounds the puncture hole. Punctures through the tread can be repaired if they are not too large, but
punctures to the sidewall should not be repaired. Tires must be removed from the rim to be properly
inspected before being plugged and patched.
Tire Fundamentals
Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This
information identifies and describes the fundamental characteristics of the tire and also provides a tire
identification number for safety standard certification and in case of a recall.
14-14
R O U T I N E
M A I N T E N A N C E
Information on Passenger Vehicle Tires
Please refer to the diagram below.
P—The “P” indicates the tire is for passenger vehicles. NOTE: Passenger car tires are not recommended
for use on trailers, because the capacity ratings are not marked on the side walls of these tires. In the event
a passenger car tire is used, the capacity must be de-rated by 10%.
Next number—This three-digit number gives the width in millimeters of the tire from sidewall edge to
sidewall edge. In general, the larger the number, the wider the tire.
Next number—This two-digit number, known as the aspect ratio, gives the tire’s ratio of height to width.
Numbers of 70 or lower indicate a short sidewall for improved steering response and better overall
handling on dry pavement.
R—The “R” stands for radial. Radial ply construction of tires has been the industry standard for the past
20 years.
Next number—This two-digit number is the wheel or rim diameter in inches. If you change your wheel
size, you will have to purchase new tires to match the new wheel number.
Next number—This two- or three-digit number is the tire’s load index. It is a measurement of how
much weight each tire can support. You may find this information in your owner’s manual. If not, contact
a local tire dealer. NOTE: You may not find this information on all tires because it is not required by law.
14-15
R O U T I N E
M A I N T E N A N C E
M+S—The “M+S” or “M/S” indicates that the tire has some mud and snow capability. Most radial tires
have these markings.
Speed Rating—The speed rating denotes the speed at which a tire is designed to be driven for extended
periods of time. The ratings range from 99 miles per hour (mph) to 186 mph. These ratings are listed
below. NOTE: You may not find this information on all tires because it is not required by law.
Letter Rating
Speed Rating
Q
R
S
T
U
H
V
W
Y
99 mph
106 mph
112 mph
118 mph
124 mph
130 mph
149 mph
168* mph
186* mph
*For tires with a maximum speed capability over 149 mph, tire manufacturers sometimes use the letters
ZR. For those with a maximum speed capability over 186 mph, tire manufacturers always use the letters
ZR.
U.S. DOT Tire Identification Number—This begins with the letters “DOT” and indicated that the
tire meets all federal standards. The next two numbers or letters are the plant code where it was
manufactured, and the last four numbers represent the week and year the tire was built. For example, the
numbers 3197 means the 31st week of 1997. The other numbers are marketing codes used at the
manufacturer’s discretion. This information is used to contact customers if a tire defect requires a recall.
Tire Ply Composition and Materials Used—The number of plies indicates the number of layers of
rubber-coated fabric in the tire. In general, the greater the number of plies, the more weight a tire can
support. Tire manufacturers also must indicate the materials in the tire, which include steel, nylon,
polyester, and others.
Maximum Load Rating—This number indicates the maximum load in kilograms and pounds that can
be carried by the tire.
Maximum Permissible Inflation Pressure—This number is the greatest amount of air pressure that
should ever be put in the tire under normal driving conditions.
14-16
R O U T I N E
M A I N T E N A N C E
Additional Information on Light Truck Tires
Please refer to diagram below.
Tires for light trucks have other markings besides those found on the sidewalls of passenger tires.
LT—The “LT” indicates the tire is for light trucks or trailers.
ST—An “ST” is an indication the tire is for trailer use only.
Max. Load Dual kg (lbs) at kPa (psi) Cold—This information indicates the maximum load and tire
pressure when the tire is used as a dual; that is, when four tires are put on each rear axle (a total of six or
more tires on the vehicle).
Max. Load Single kg (lbs) at kPa (psi) Cold—This information indicates the maximum load and tire
pressure when the tire is used as a single.
Load Range—This information identifies the tire’s load-carrying capabilities and its inflation limits.
Vehicle Load Limits
Determining the load limits of a vehicle includes more than understanding the load limits of the tires
alone.
On a motor home, there is a Federal certification label that is affixed to either the hinge pillar, door-latch
post, or the door edge that meets the door-latch post, next to the driver’s seating position. If none of
14-17
R O U T I N E
M A I N T E N A N C E
these locations is practicable, this label will be located to the left side of the instrument panel, or affixed to
the inward-facing surface of the door next to the driver’s seating position.
The certification label will indicate the vehicle’s gross vehicle weight rating (GVWR). This is the most
weight the fully loaded vehicle can weight. It will also provide the gross axle weight rating (GAWR). This
is the most a particular axle can weigh. If there are multiple axles, the GAWR of each axle will be
provided.
For motor homes, in the same location as the certification label described above, there is a vehicle placard.
This placard provides tire and loading information. In addition, this placard will show the vehicle’s seating
capacity for people and a statement regarding maximum cargo capacity.
Cargo Capacities
For motor homes, cargo can be added to the vehicle, up t the maximum weight specified on the placard.
For motorized vehicles, the combined weight of passengers and cargo is provided as a single number. If
fewer people are traveling, more cargo can be added. If more people are involved, the weight of cargo
must be reduced. In any case, remember: the total weight of a fully loaded vehicle, including passengers,
can not exceed the stated GVWR.
For motor homes, the water and propane also need to be considered. The weight of fully filled propane
containers is considered part of the weight of the RV before it is loaded with people or cargo and is not
considered part of the disposable cargo load. Water, however, is a cargo weight and is treated as such. If
there If there is a fresh water storage tank of 100 gallons, this tank when filled would weigh about 800
pounds. If more cargo or people are being transported, water can be off-loaded to keep the total amount
of cargo added to the vehicle within the limits of the GVWR so as not to overload the vehicle.
Understanding this flexibility will allow you, the owner, to make choices that fit your travel and camping
needs.
When loading your cargo, be sure it is distributed evenly to prevent overloading front to back and side to
side. Heavy items should be placed low and as close to the axle positions as reasonable. Too many items
on one side may overload a tire. The best way to know the actual weight of the vehicle is to weigh it at a
public scale. Talk to your RV dealer to discuss the weighing methods needed to capture the various
weights related to the RV. This would include weights for the following: axles, wheels, hitch and total
weight.
How Overloading Affects Your RV and Tires
The results of overloading can have serious consequences for passenger safety. Too much weight on your
vehicle’s suspension system can cause spring, shock absorber, or brake failure, handling or steering
problems, irregular tire wear, tire failure or other damage.
An overloaded vehicle is hard to drive and hard to stop. In cases of serious overloading, brakes can fail
completely, particularly on steep hills. The load a tire will carry safely is a combination of the size of tire, its
load range, and corresponding inflation pressure.
14-18
R O U T I N E
M A I N T E N A N C E
Excessive loads and/or under-inflation cause tire overloading and, as a result, abnormal tire flexing occurs.
This situation can generate an excessive amount of heat within the tire. Excessive heat may lead to tire
failure.
It is the air pressure that enables a tire to support the load, so proper inflation is critical. Since RVs can be
configured and loaded in many ways, air pressures must be determined from actual loads (determined by
weighing) and taken from the load and inflation tables provided by the tire manufacturer. These air
pressures may differ from those found on the certification label. However, they should never exceed the
tire limitation for load or air pressure. If you discover that your tires cannot support the actual weights, the
load will need to be lightened.
Tire Safety Tips
Preventing Tire Damage
•
Slow down if you have to go over a pothole or other object in the road.
•
Do not run over curbs or other foreign objects in the roadway, and try not to strike the curb
when parking.
Tire Safety Checklist
•
Check tire pressure regularly (at least once a month), including the spare.
•
Inspect tires for uneven wear patterns on the tread, cracks, foreign objects, or other signs of wear
or trauma.
•
Remove bits of glass and foreign objects wedged in the tread.
•
Make sure your tire valves have valve caps.
•
Check tire pressure before going on a long trip.
•
Do not overload your vehicle. Check the Tire Information and Loading Placard or User’s Manual
for the maximum recommended load for the vehicle.
Section Two:
Steps for Determining Correct Load Limit
1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX
lbs” on your vehicles placard.
2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
14-19
R O U T I N E
M A I N T E N A N C E
3. Subtract the combined weight of the driver and passengers from XXX kilograms or XXX
pounds.
4. The resulting figure equals the available amount of cargo and luggage capacity. For example, if the
“XXX” equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of
available cargo and luggage capacity is 650 lbs. (1400-750 (5 x 150) = 650 lbs.)
5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight
may not safely exceed the available cargo and luggage capacity calculated in Step #4.
6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle.
Consult this section to determine how this reduces the available cargo and luggage capacity of
your vehicle.
Section Three:
Glossary of Tire Terminology
Accessory weight—The combined weight (in excess of those standard items which may be replaced) of
automatic transmission, power steering, power brakes, power windows, power seats, radio and heater, to
the extent that these items are available as factory-installed equipment (whether installed or not).
Bead—The part of the tire that is made of steel wires, wrapped or reinforced by ply cords and that is
shaped to fit the rim.
Bead separation—This is the breakdown of the bond between components in the bead.
Bias ply tire—A pneumatic tire in which the ply cords that extend to the beads are laid at alternate angles
substantially less than 90 degrees to the centerline of the tread.
Carcass—The tire structure, except tread and sidewall rubber which, when inflated, bears the load.
Chunking—The breaking away of pieces of the tread or sidewall.
Cold inflation pressure—The pressure in the tire before you drive.
Cord—The strands forming the plies in the tire.
Cord separation—The parting of cords from adjacent rubber compounds.
Cracking—Any parting within the tread, sidewall, or inner liner of the tire extending to cord material.
CT—A pneumatic tire with an inverted flange tire and rim system in which the rim is designed with rim
flanges pointed radially inward and the tire is designed to fit on the underside of the rim in a manner that
encloses the rim flanges inside the air cavity of the tire.
14-20
R O U T I N E
M A I N T E N A N C E
Curb weight—The weight of a motor vehicle with standard equipment including the maximum capacity
of fuel, oil, and coolant, and, if so equipped, air conditioning and additional weight optional engine.
Extra load tire—A tire designed to operate at higher loads and at higher inflation pressures than the
corresponding standard tire.
Groove—The space between two adjacent tread ribs.
Gross Vehicle Weight Rating (GVWR)—The maximum permissible weight of this fully loaded
motorhome.
Gross Axle Weight Rating ((GAWR)—The value specified as the load carrying capacity of a single axle
system, as measured at the tire-ground interfaces.
Hitch Weight—The vertical trailer load supported by the hitch ball.
Innerliner separation—The parting of the innerliner from cord material in the carcass.
Intended outboard sidewall—The sidewall that contains a white-wall, bears white lettering or bears
manufacturer, brand, and /or model name molding that is higher or deeper than the same molding on the
other sidewall of the tire or the outward facing sidewall of an asymmetrical tire that has a particular side
that must always face outward when mounted on a vehicle.
Light truck (LT) tire—A tire designated by its manufacturer as primarily intended for use on lightweight
trucks or multipurpose passenger vehicles.
Load rating—The maximum load that a tire is rated to carry for a given inflation pressure.
Maximum load rating—The load rating for a tire at the maximum permissible inflation pressure for that
tire.
Maximum permissible inflation pressure—The maximum cold inflation pressure to which a tire may
be inflated.
Maximum loaded vehicle weight—The sum of curb weight, accessory weight, vehicle capacity weight,
and production options weight.
Measuring rim—The rim on which a tire is fitted for physical dimension requirements.
Non-pneumatic rim—A mechanical device which, when a non-pneumatic tire assembly incorporates a
wheel, supports the tire, and attaches, either integrally or separably, to the wheel center member and upon
which the tire is attached.
Non-pneumatic tire assembly—A non-pneumatic tire, alone or in combination with a wheel or wheel
center member, which can be mounted on a vehicle.
14-21
R O U T I N E
M A I N T E N A N C E
Normal occupant weight—This means 68 kilograms (150 lbs.) times the number of occupants specified
in the second column of Table I of 49 CFR 571.110.
Occupant distribution—The distribution of occupants in a vehicle as specified in the third column of
Table I of 49 CFR 571.110.
Open splice—Any parting at any junction of tread, sidewall, or innerliner that extends to cord material.
Outer diameter—The overall diameter of an inflated new tire.
Overall width—The linear distance between the exteriors of the sidewalls of an inflated tire, including
elevations due to labeling, decorations, or protective bands or ribs.
Pin Weight—The vertical trailer load supported by the king pin of a fifth wheel hitch.
Ply—A layer of rubber-coated parallel cords.
Ply separation—A parting of rubber compound between adjacent plies.
Pneumatic tire—A mechanical device made of rubber, chemicals, fabric and steel or other materials,
that, when mounted on an automotive wheel, provides the traction and contains the gas or fluid that
sustains the load.
Production options weight—The combined weight of those installed regular production options
weighing over 2.3 kilograms (5 lbs.) in excess of those standard items which they replace, not previously
considered in curb weight or accessory weight, including heavy duty brakes, ride levelers, roof rack, heavy
duty battery, and special trim.
Radial ply tire—A pneumatic tire in which the ply cords that extend to the beads are laid at substantially
90 degrees to the centerline of the tread.
Recommended inflation pressure—This is the inflation pressure provided by the vehicle manufacturer
on the Tire Information label and on the Certification/ VIN tag.
Reinforced tire—A tire designed to operate at higher loads and at higher inflation pressures than the
corresponding standard tire.
Rim—A metal support for a tire or a tire and tube assembly upon which the tire beads are seated.
Rim diameter—This means the nominal diameter of the bead seat.
Rim size designation—This means the rim diameter and width.
Rim type designation—This means the industry of manufacturer’s designation for a rim by style or
code.
Rim width—This means the nominal distance between rim flanges.
14-22
R O U T I N E
M A I N T E N A N C E
Section width—The linear distance between the exteriors of the sidewalls of an inflated tire, excluding
elevations due to labeling, decoration, or protective bands.
Sidewall—That portion of a tire between the tread and bead.
Sidewall separation—The parting of the rubber compound from the cord material in the sidewall.
Test rim—The rim on which a tire is fitted for testing, and may be any rim listed as appropriate for use
with that tire.
Tread—That portion of a tire that comes into contact with the road.
Tread rib—A tread section running circumferentially around a tire.
Tread separation—Pulling away of the tread from the tire carcass.
Treadwear indicators (TWI)—The projections within the principal grooves designed to give a visual
indication of the degrees of wear of the tread.
Vehicle capacity weight—The rated cargo and luggage load plus 68 kilograms (150 lbs.) times the
vehicle’s designated seating capacity.
Vehicle maximum load on the tire—The load on an individual tire that is determined by distributing to
each axle its share of the maximum loaded vehicle weight and dividing by two.
Vehicle normal load on the tire—The load on an individual tire that is determined by distributing to
each axle its share of the curb weight, accessory weight, and normal occupant weight (distributed in
accordance with Table I of CFR 49 571.110) and dividing by 2.
Weather side—The surface area of the rim not covered by the inflated tire.
Wheel center member—In the case of a non-pneumatic tire assembly incorporating a wheel, a
mechanical device which attached, either integrally or separably, to the non-pneumatic rim and provides
the connection between the non-pneumatic rim and the vehicle; or, in the case of a non-pneumatic tire
assembly not incorporating a wheel, a mechanical device which attaches, either integrally or separably, to
the non-pneumatic tire and provides the connection between tire and the vehicle.
Wheel-holding fixture—The fixture used to hold the wheel and tire assembly securely during testing.
14-23
R O U T I N E
M A I N T E N A N C E
Tire Pressure
Correct tire inflation pressure is essential to maximizing the life of the tires and assuring the safety of
the vehicle and its occupants. Driving with tires that are not correctly inflated for the load of the
motor home is dangerous and may cause premature wear, tire damage, and/or loss of control of the
motor home.
An underinflated tire will build up excessive heat that may actually approach the vulcanization
temperature of the rubber and lead to tread separation and/or disintegration of the tire.
Additionally, underinflated tires will also cause poor handling of the motor home, rapid and/or
irregular tire wear, and an increase in rolling resistance of the motor home which, in turn, produces a
decrease in fuel economy of operation.
An overinflated tire will reduce the tire’s “footprint” (i.e., its actual contact with the road); thus,
reducing the traction, braking capacity, and handling of the motor home. A tire that is overinflated
for the load that it is carrying will also contribute to a harsh ride, uneven tire wear, and the tire itself
will be more susceptible to impact damage.
Maintaining correct tire pressure for each loaded wheel position on the motor home is critically
important and must be a part of regular vehicle maintenance.
Tire Maximum Load Rating
Federal law requires that the maximum load rating be molded into the sidewall of the tire. If one looks at
a tire sidewall, one may see some “typical” information, such as:
Max. Load Single 3640 Lbs at 85 psi cold
Max. Load Dual
3415 Lbs at 85 psi cold
The maximum load allowed for the size tire and load rating and the minimum cold air-inflation pressure
needed to carry that stated maximum load are noted on the tire. Using less air pressure would reduce the
load-carrying capacity of the tire. The amount of air pressure one needs depends on the weight of
the fully loaded motor home. Consequently, one cannot determine the correct air-inflation
pressure, unless one knows the actual weights of the motor home.
Weighing the Motor Home
Earlier, in Chapter 1, the procedures for weighing the motor home were presented (see p. 1-7). These
procedures provided the weighing of a “non-loaded” (i.e., not stocked with the possessions and
provisions the user would normally have onboard for travel) motor home. Obviously, any additional
weight stored onboard (inside and underneath) the motor home will contribute to the overall weight of
the motor home.
14-24
R O U T I N E
M A I N T E N A N C E
If not stored uniformly throughout the motor home, additional weight of the possessions and provisions
of the motor-home user will load each axle and each tire differently (front-to-rear and side-to-side
distribution of that additional weight). Accordingly, it is necessary to weigh the motor home fully
loaded as the user would have it for travel, including occupants. Moreover, it is necessary to
weigh each tire position individually.
Overloading the motor home can produce problems with the tires, wheels, springs, brakes, drive train,
and other motor home assemblies. In addition, an overloaded motor home uses more fuel, is more
difficult to handle properly, and can lead to driver fatigue more quickly. In a worst-case condition, if any
component should fail, this could result in loss of control of the motor home and subsequent damage. In
certain states, the Highway Patrol routinely weighs motor homes to check for overloaded axle weights.
Therefore, there are many good reasons for assuring that the motor home is properly loaded and not
overloaded—this can be accomplished through a proper weighing of the fully loaded motor home.
One can find various places that have certified public scales where one’s motor home can be weighed.
For example, moving and storage company lots, farm suppliers with grain elevators, gravel pits, recycling
companies, and large-scale commercial-truck stops are some of the possible locations for weighing the
motor home. One can also check the Yellow Pages of the telephone book for “scales – public” or
“weighers” to determine other locations for weighing the motor home. A brief overview of the
procedure for weighing the motor home is shown in Figure 14-7.
Figure 14-7. Procedure for Weighing the Motor Home (Each Tire Position Individually)
14-25
R O U T I N E
M A I N T E N A N C E
Note 1: From the tire manufacturer’s load and inflation tables or the sidewall of the tires mounted on the motor home.
Note 2: If the motor home has duals, read dual capacity from the tire and multiply by 2 (two) to obtain dual-assembly loadcarrying capacity.
More detailed information can be found in the manufacturer’s literature (Figure 14-8) associated with the
chassis and/or the tires provided with the motor home. For example, the following table illustrates the
inflation pressures for Michelin tires as a
function of the loads per position for a
specified speed of the motor home. In this
manner, one can determine the appropriate
inflation pressures for each of the tires on the
motor home, as a function of the loads they
are to carry on the trip(s) the motor home is to
take.
Whenever there is a significant change in the
loading regimen of the motor home, it would
be wise to re-calculate the load weights of the
tires to assure optimal use of the motor home.
Figure 14-8. Typical Inflation Pressures for Motor Home Tires
Frequency of Checking Tire Inflation Pressures
When one has determined the “correct” tire inflation pressures for each of the motor-home tires (as a
function of the “fully loaded” condition, of course) and inflated the tires (Figure 14-9) under “cold” (i.e.,
tires haven’t been driven for more than one mile) conditions; then the air pressures in the tires should be
periodically checked to make sure that they retain their proper pressures. It is recommended that tire
pressures be checked at least once a month (every two weeks would be better) and before any major trip.
On long trips, the tires should be checked every “drive”
morning. On short trips (a day or less), the tires should be
checked before one departs on the trip and again before
one returns home.
Figure 14-9. Rear Tires on Zephyr
Check tire pressures when they are “cold”; that is, the tires
haven’t been driven at all or, at most, less than one mile
before being measured. In this manner, the tire pressure
has not been increased by the heating associated with both
tire sidewall and tread flexure associated with traveling. If
one must check tires that are warm or hot, remember that
they will necessarily read higher than normal. Do not
“bleed” these tires down to the “cold pressure” readings,
as they will probably then be underinflated when they are
14-26
R O U T I N E
M A I N T E N A N C E
actually cool. Don’t make any adjustments to tire pressures when the tires are warm or hot, if such can be
avoided.
To make these tire-pressure measurements, it is recommended that one purchase a quality, truck-tire air
gauge which has an angled dual head. This type of gauge allows one to check inflation pressures of both
the inner dual wheel which has the valve stem pointing towards one and on the outer wheel which has the
valve stem pointing away from one. Pressure-sealing valve caps should always be used to protect the
valve stems and prevent air from escaping from the valve stems.
Tire Wear, Balance, and Wheel Alignment
In addition to tire inflation considerations, the tires should also be periodically examined for other types of
normal “wear and tear.” If installed and maintained properly, all tires mounted on the motor home
should wear in a smooth, even pattern. If the tires begin to show irregular wear patterns and the motorhome alignment is still correct, then sometimes just rotating the tires by changing wheel position and
rotation of the tires will allow the tires to wear evenly. Check with the chassis manufacturer and its
literature (in the Owner’s Information Package) for particulars on maintaining proper wheel alignment.
Tire rotation should include the spare tire in the rotation pattern and changing the direction of rotation of
the tires. Tires can be rotated front-to-rear and side-to-side.
Tire Cleaning
Proper cleaning of the tires will assure maximum years of service. A soft brush and the normal mild soap
should be used to clean the tires. Use care in applying any tire “dressing” product as these contain
petroleum derivatives, alcohol, or silicones which may cause deterioration of the rubber, possibly leading
to cracking, and accelerate the aging process. In many instances it isn’t the actual dressing itself, but the
reaction of that product with the antioxidant in the tire. Heat can compound this problem also.
INTERIOR CARE
Important
The fading of upholstery, carpet, and other interior fabrics is generally caused by
excessive sunlight. The drapes, blinds, or other shades should be kept closed
when the vehicle is parked for an extended period of time to minimize the fading.
Normal deterioration of the appearance of such items caused by wear and/or
exposure to strong lighting is not covered by the Tiffin Motorhomes Limited
Warranty.
14-27
R O U T I N E
M A I N T E N A N C E
Carpet
A weekly routine of vacuuming the carpet and fabrics throughout the vehicle is recommended; the
vacuum system (Figure 14-11) has a central connection (Figure 14-10) within
the motor home wherein a vacuum hose can be
connected and the necessary vacuuming performed, as
desired.
Doing such will prevent an undue
accumulation of dirt which can detract from the
appearance of the carpeting and, thus, shorten its
expected life. Remember to empty or replace vacuum bags
Figure 14-10.
before they become overly full—this practice will assure
Vacuum Hose
Coupling
that sufficient vacuuming capability is readily available to
handle any and all cleaning situations that may arise. In carpet areas that
receive the most sunlight, keeping the curtains closed whenever possible will
minimize fading. Also act quickly when anything is spilled or dropped onto
the carpet to prevent or minimize staining.
Figure 14-11.
Vacuum Cleaner
System
To connect the cleaning hose, raise the wall remote inlet valve door, (Figure 14-10) and align hose end
coupling with slots on each side of intake opening. Firmly push into intake opening. Make sure hose end
coupling is connected and is locked in place. To disconnect the hose, simply push in the slots on each side
of the hose coupling and pull hose end straight out.
To start the vacuum cleaner:
1. Push the on/off switch on the main vacuum to the “on” position. Indicator light in switch will
come on. Now the vacuum will come on and off by using the wall remote inlet valve.
2. To turn on, raise the door up.
3. To turn off, lower the inlet valve door down and the vacuum will turn off. The main vacuum
on/off switch should stay in the “on” position all the time, except when traveling.
4. To turn completely off, return main vacuum on/off switch to the “off” position. The switch light
will go off.
Warning
This appliance has a THERMAL PROTECTOR built in the motor to prevent
overheating. If motor will not operate or shuts down while in operation wait 30
minutes; it will reset automatically. Turn unit off while it resets. If the motor does
not come on, or Thermal Protector trips off again after a short period, service may
14-28
R O U T I N E
M A I N T E N A N C E
be needed. A qualified service technician should perform service.
The vacuum cleaning system comes with an array of attachments that can be connected to the hose ends
for extensive cleaning purposes. Make sure they are firmly pushed in and twist to hold in place.
For further instructions to change the dust bag, use the attachments, and proper cleaning technique, refer
to the specific Owner’s Manual located in your motor home.
Fabrics
The fabrics (Figure 14-12) used in this Tiffin motor home for the bedspread (Figure 14-13),
draperies, headboard, and valances contain fire-retardant
additives that may be damaged by use of improper cleaning
products. Cleaning instructions for these items are DRY
CLEAN ONLY.
Water-based products are not
recommended for cleaning the fabrics in your new vehicle.
Most water-based, householdcleaning products are not
formulated for use on these
fabrics and may cause excessive
Figure 14-12. Furniture Fabrics
shrinkage or fading. For best
results, the fabrics in this vehicle should be cleaned by a
professional carpet/upholstery cleaner.
Spills, spots, or stains should be treated as soon as possible to avoid
permanent damage to the fabrics. If a spill occurs, blot the fluid
Figure 14-13. Bedroom Fabrics
with a dry towel; do not rub the spill as rubbing may cause the
liquid to “set” in the fabric and cause a stain. When attempting to clean a spot or stain, always start
from the outside and work inward to avoid spreading the stain further. Some stains or soils are
extremely difficult or impossible to be removed completely. These stains should receive immediate,
professional attention. Spills, spots, stains, or soiled areas are the responsibility of the owner and are
not covered by Tiffin Motorhomes Limited Warranty.
14-29
R O U T I N E
M A I N T E N A N C E
Warning
When cleaning the upholstery and fabric of the motor home, do not use lacquer
thinner, nail polish remover, laundry soaps, or bleach. Never use carbon
tetrachloride or gasoline for cleaning purposes. These substances may cause
damage to the materials being cleaned and most are highly flammable.
Walls and Ceiling
The wall and ceiling coverings should be cleaned periodically to maintain a new appearance. Use a
non-abrasive cleaner with a soft cloth on the walls. Do not use solvents of any kind, as those
solvents may damage the surfaces being so cleaned.
Dashboard
To keep the dashboard (Figure 14-14) in like-new condition,
follow these guidelines:
DO:
•
•
•
Dust and clean the dashboard with a soft, damp
cloth or chamois, wiping the service gently.
Use a mild detergent and lukewarm water.
Dry the surface, after washing and rinsing, by
blotting with a damp cloth or chamois.
Figure 14-14. Typical Dashboard
DO NOT:
• Use harsh chemicals that may damage the dashboard.
• Use any cloth containing grit or abrasive particles or kitchen-scouring
compounds to clean or dust the dashboard.
• Subject the dashboard to hard, direct blows.
• Use boiling water, strong solvents, or other such materials to clean the
dashboard, as they will soften the plastic.
Woodwork & Floors
The wood cabinetry (Figure 14-15) should be cared for with furniture polish to
sustain the natural beauty and luster of the wood. This procedure will also Figure 14-15.
keep the cabinetry looking new, prevent the wood from drying, and reduce
14-30
Zephyr Kitchen
R O U T I N E
M A I N T E N A N C E
chances of accidental staining or aging.
Use area rugs and floor mats by the entrance door to trap dirt. Use soap and water to clean the
(ceramic) flooring, begin by vacuuming the floor to remove loose dust and dirt. Then, damp mop
the floor with a cleaning solution consisting of any standard cleaning solution available through
retail-sales outlets (e.g., Wal-Mart, Kmart, Target) or grocery stores. The mop should be damp, but
not dripping. Feel free to use soap-based cleaners, scouring powders, steel wool, abrasive cleaners,
wax, or polish on the ceramic floor as this floor is impervious to these cleaning agents.
To remove stubborn spots like shoe polish, oil, tar, markers, scuffs, and the like; use a household
solvent or nail-polish remover on those spots; then wipe those treated areas with a damp cloth.
To remove chocolate, grease, juice, or wine; use warm water and any off-the-shelf abrasive cleaner
(cleansers and the like). To remove candle wax or chewing gum, carefully scrape off when the
material has hardened. For further tips, please see the manufacturer’s recommended information
sheet in your Tiffin Motorhomes Owner’s Information Package.
Countertops
To care properly for the countertops (Figure 14-16) in your new motor home, always use a heat pad
or trivet to protect the surface from hot objects that may
mar or damage the countertop surface. Hot pans and heatproducing appliances (such as electric skillets), when set
directly on top of the countertop, can possibly mar the
beauty and finish of the product.
Figure 14-16. Kitchen Countertop
Additionally, since any heat-producing appliances can also
damage countertop seams, it is essential to check with
Tiffin Motorhomes to identify seam locations to avoid
them during subsequent use of the motor home. Although
solid surfacing is repaired easily, certain steps
should be taken to protect it from any
unnecessary harm or damage.
Be sure to use a cutting board, rather than cutting directly on the countertop surfaces. Although
minor scratches and cuts can be repaired, a little care will assure that the countertop surfaces will
keep looking new for years.
Avoid using harsh chemicals on the countertop. Wipe the countertop with a damp cloth to remove
water spots. For most dirt and stains, wipe with a damp cloth and use soapy water or glass cleaners
(e.g., Windex).
14-31
R O U T I N E
M A I N T E N A N C E
If a stain doesn’t respond to soap and water, for a matte finish, apply an abrasive cleanser and buff it
with a Scotch-Brite pad, using a circular motion. Use the same technique in the case of a cigarette
burn. If the finish is a gloss finish, please contact the dealer for specific cleaning instructions.
Do not expose the surface to harsh chemicals, such as paint remover, turpentine, nail polish
remover, or any stove and drain cleansers. If these chemicals should come into contact with the
countertop surfaces, immediately wash off these chemicals, using appropriate safety measures to
avoid injury.
In the event of subsequent staining or spotting, sand the affected surface lightly with fine sandpaper
(400 grit or finer), then buff in a circular motion with a Scotch-Brite pad.
Accessories
The light fixtures, bath accessories, and faucets can be cleaned by wiping with a soft, damp cloth.
Washing with warm water will remove dry water spots. Do not use cleaners that contain harsh or
abrasive chemicals. Alcohol or other similar solvents should never be used.
Detectors
The CO/ LP Gas detectors are self-contained and DO NOT require any maintenance other than normal
cleaning and periodic testing. The CO/LP Gas detector operates solely on 12 volt.
It is important that you periodically test your CO/LP Gas detector for any irregularities and to ensure
proper operation. When cleaning the case on any of the detectors, use a damp cloth or paper towel. Do
not spray cleaners or wax directly into the case as this action may cause false alarms or hinder the normal
operation of the detectors.
Condensation
Important
Since surface condensation within the motor home cannot be controlled by the
manufacturer, damage caused by condensation is not covered by the Tiffin
Motorhomes Limited Warranty.
Damage may occur to your motor home if excessive condensation exists. Accumulation of
condensation on surfaces within your motor home occurs when warm, moist air contacts a cool
surface. It is most evident on the inside of windows, but this problem can be controlled by:
14-32
R O U T I N E
M A I N T E N A N C E
1. Slightly opening a window or roof vent to allow the moisture to escape from the motor
home.
2. A small dehumidifier is also very effective in removing moisture from the air.
Condensation levels are highest during times when a person is cooking or taking a shower in the
motor home, but these occasions are not the only times condensation is present. Walls and ceiling
panels may become wet when the moisture accumulates on these surfaces. Tiffin Motorhomes does
not recommend the use of any catalytic heaters because of resulting extensive condensation.
ROUTINE MAINTENANCE SCHEDULES
Important
Always follow the chassis maintenance guidelines found in the chassis
manufacturer’s owner’s manual.
All routine maintenance is the responsibility of the owner and is not covered by the Tiffin
Motorhomes Limited Warranty. Use the maintenance record found in Chapter 15 to record all
performed maintenance as required.
Please note that any damage caused by improper or unperformed maintenance is not covered by the
Tiffin Motorhomes Limited Warranty. Items supplied by other manufacturers may require specific
individual maintenance not listed herein. Please refer to the manufacturers’ suggested maintenance
guidelines in the Owner’s Information Package.
Important
Cosmetic adjustments and alignments must be performed within the first three
months from date of original purchase for warranty consideration. Thereafter,
these items are considered routine maintenance.
14-33
R O U T I N E
M A I N T E N A N C E
Monthly
•
•
Check the water levels of the batteries.
Visually inspect the fire extinguisher(s).
Every Three Months
•
•
•
•
•
•
•
•
•
Check LP gas lines for leaks with soap solution or leak detector.
Clean the microwave hood exhaust fan filter and blades.
Test smoke alarm, carbon monoxide/LP gas detector.
Check operation of windows, latches, and hinges.
Clean the roof; clean the roof ducted air conditioner filter or filters.
Clean and inspect door and window seals; reseal where necessary.
Inspect and reseal around the tub and shower area where necessary.
Lubricate the exterior door hinges and latches with a graphite (silicone) lubricant.
Check, clean, and tighten battery cables and inspect batteries for proper fluid levels.
Every Six Months
•
•
•
•
•
•
•
•
Inspect any slide-out for proper seal. If realignment is necessary, please contact an
authorized Tiffin Motorhomes Service Center.
Inspect all exterior rubber seals and apply an UV inhibitor, such as 303 Protectant, s
necessary.
Change the battery in the smoke detector.
Rotate tires as recommended by the tire manufacturer.
Check all gas appliances for proper operation.
Have the LP system inspected by a qualified technician.
Lubricate the movable parts on the entrance step.
Change the batteries in both the smoke detector and the CO/LP gas detector.
Annually
•
•
•
Inspection of roof seams and joints should be performed by an authorized Motorhomes
Service Center. If resealing is necessary, it is the owner’s responsibility and is not covered by
the Tiffin Motorhomes Limited Warranty.
Sanitize the fresh water system.
Wax and buff all gel-coat surfaces on the vehicle as described previously in this chapter.
14-34
R O U T I N E
M A I N T E N A N C E
Winterizing
To store your motor home for the winter months, it is necessary to winterize
the water system (Figure 14-17) to help prevent freezing of this system. To
do this, follow these instructions:
1. Drain all the water from the water system including the holding
tank(s), and the water tank; also drain the water filter, if installed.
For the holding tank(s), open the gate valve(s) to drain the tanks.
(NOTE: This procedure is to be performed only at a wastewater
pumping station to prevent dumping of contaminated water
elsewhere). For the water tank, open the green-handled valve to drain
the tank; then close the green-handled valve. If an optional water
filter is installed, remove the filter cartridge and store it in a clean
environment (e.g., resealable plastic bag); empty any excess water
from the filter housing and replace the housing.
Figure 14-17. Winterizing the
Water System
2. Disconnect the inlet connection to the water pump [in the sanitation compartment under the
motor home]. Attach the supplied, vinyl hose (via the plastic coupling on the hose) to the
inlet connection and hand-tighten that connection; do not over-tighten.
3. Place the other end of the hose into a gallon of freshwater system antifreeze (one can refer
to the local Tiffin Motorhomes dealer or representative for the freshwater antifreeze
formulation for your specific area). NOTE: Do not use automotive antifreeze; use only
antifreeze approved for RV applications; otherwise, damage to the systems being protected
may result.
4. Turn “on” the water pump to start the flow of antifreeze. Turn “on” each faucet, one at a
time, and allow pure antifreeze to run through that piping. Let about one cup drop into the
drains to protect the traps.
5. When all the antifreeze is withdrawn from the bottle, disconnect the clear vinyl hose from
the water-pump inlet connection and reconnect the inlet line to the water pump. (This may
require more than one gallon of antifreeze).
6. When the winterizing process is completed, turn the water pump “off” and then reconnect
the water line. Store the vinyl hose for future use.
7. Open the water supply valve that controls flow from the pump to the tank to help prevent
freezing on that water line.
Note: Remember, the motor home also has an exterior shower; therefore, this system must be
winterized, as well.
14-35
R O U T I N E
M A I N T E N A N C E
Washer/Dryer
For instructions on properly winterizing the stacked washer/dryer, please refer to the specific
owner’s manual located in the Owner’s Information Package.
Refrigerator
The proper steps must be taken to ensure that the residential refrigerator is correctly winterized. Note that
before winterizing the Amana refrigerator, the water filters must be removed. Please see the owner’s
manual for the Amana residential refrigerator that will be included in the Owner’s Information Package.
Hydro-Hot Heating System
For instructions on properly winterizing the Hydro-Hot heating system, please refer to the specific
owner’s manual located in the Owner’s Information Package.
De-Winterizing
1. To de-winterize your motor home, open both of the low-point drains to allow the
antifreeze solution to drain from the water system.
2. Next, close the low-point drains and connect your motor home to the city water system.
Put water in the freshwater tank and pump at least one gallon through the water pump
to remove the antifreeze from the water pump. Keep the water heater supply valve
closed and the water heater bypass valves open. The supply valve for the freshwater
tank from the pump must remain closed.
3. As in winterizing, open the kitchen faucet, bath faucet, inside and outside showers,
turning “on” both the hot- and the cold-water valves and flushing the toilet until the
antifreeze solution is flushed out of the system and the water flow is clear.
4. Once the system has been flushed, open the freshwater tank supply valve from the
pump and the icemaker valve.
5. Reinstall the optional water filter.
6. Be sure to close the fresh water tank drain valves to allow the tank to fill.
14-36
M A I N T E N A N C E
&
D A T A
C H A R T S
Chapter
15
Maintenance & Data Charts
15-1
M A I N T E N A N C E
&
D A T A
C H A R T S
RV Owner’s Data Sheet
Please enter the following information in the table for your future use:
Zephyr: Year: __________ Model #: ____________________ Tiffin Serial #: __________________
Appliance
Brand
Model Number
Serial Number
Refrigerator
Washer / Dryer (optional)
Water Heater
Microwave
Inverter
Television, Front
Back-Up Monitor, Rear
AM/FM/CD Stereo
DVD Entertainment Center
Air Conditioner
Generator
Reproduction Master – Copy this sheet and use copy to maintain your maintenance records. You
may wish to keep the completed sheets in a three-ring binder for your permanent record.
15-2
M A I N T E N A N C E
&
D A T A
C H A R T S
RV Owner’s Maintenance Record
Please enter the following information in the table for your future use:
Zephyr: Year: __________ Model #: ____________________ Tiffin Serial #: __________________
Date / Mileage
Service Work Performed
Performed by
Cost ($)
Reproduction Master – Copy this sheet and use copy to maintain your maintenance records. You
may wish to keep the completed sheets in a three-ring binder for your permanent record.
15-3
M A I N T E N A N C E
&
D A T A
C H A R T S
RV Owner’s Maintenance Record
Please enter the following information in the table for your future use:
Zephyr: Year: __________ Model #: ____________________ Tiffin Serial #: __________________
Date / Mileage
Service Work Performed
Performed by
Cost ($)
Reproduction Master – Copy this sheet and use copy to maintain your maintenance records. You
may wish to keep the completed sheets in a three-ring binder for your permanent record.
15-4
M A I N T E N A N C E
&
D A T A
C H A R T S
RV Owner’s Maintenance Record
Please enter the following information in the table for your future use:
Zephyr: Year: __________ Model #: ____________________ Tiffin Serial #: __________________
Date / Mileage
Service Work Performed
Performed by
Cost ($)
Reproduction Master – Copy this sheet and use copy to maintain your maintenance records. You
may wish to keep the completed sheets in a three-ring binder for your permanent record.
15-5
M A I N T E N A N C E
&
D A T A
C H A R T S
RV Owner’s Maintenance Record
Please enter the following information in the table for your future use:
Zephyr: Year: __________ Model #: ____________________ Tiffin Serial #: __________________
Date / Mileage
Service Work Performed
Performed by
Cost ($)
Reproduction Master – Copy this sheet and use copy to maintain your maintenance records. You
may wish to keep the completed sheets in a three-ring binder for your permanent record.
15-6
M A I N T E N A N C E
&
D A T A
C H A R T S
RV Owner’s Maintenance Record
Please enter the following information in the table for your future use:
Zephyr: Year: __________ Model #: ____________________ Tiffin Serial #: __________________
Date / Mileage
Service Work Performed
Performed by
Cost ($)
Reproduction Master – Copy this sheet and use copy to maintain your maintenance records. You
may wish to keep the completed sheets in a three-ring binder for your permanent record.
15-7
M A I N T E N A N C E
&
D A T A
C H A R T S
RV Owner’s Maintenance Record
Please enter the following information in the table for your future use:
Zephyr: Year: __________ Model #: ____________________ Tiffin Serial #: __________________
Date / Mileage
Service Work Performed
Performed by
Cost ($)
Reproduction Master – Copy this sheet and use copy to maintain your maintenance records. You
may wish to keep the completed sheets in a three-ring binder for your permanent record.
15-8
M A I N T E N A N C E
&
D A T A
C H A R T S
RV Owner’s Maintenance Record
Please enter the following information in the table for your future use:
Zephyr: Year: __________ Model #: ____________________ Tiffin Serial #: __________________
Date / Mileage
Service Work Performed
Performed by
Cost ($)
Reproduction Master – Copy this sheet and use copy to maintain your maintenance records. You
may wish to keep the completed sheets in a three-ring binder for your permanent record.
15-9
M A I N T E N A N C E
&
15-10
D A T A
C H A R T S

advertisement

Key Features

  • Detailed instructions for operation and maintenance
  • Safety considerations for driving and using appliances
  • Guidance on troubleshooting common problems
  • Information on major appliances and accessories
  • Instructions for using the LP gas system
  • Tips for maintaining the interior and exterior of the motor home

Frequently Answers and Questions

Where can I find the Tiffin Motorhomes serial number?
The Tiffin Motorhomes serial number can be found on the side of the dashboard.
What is the RVIA Weight Label?
The RVIA Weight Label is a required label that provides information about the weight distribution of the motor home, including the Gross Vehicle-Weight Rating (GVWR), Unloaded Vehicle Weight (UVW), Cargo-Carrying Capacity (CCC), and other important weight ratings.
How do I properly weigh my motor home?
To weigh your motor home properly, it should be level when the weighing process is performed. You can take your motor home to drive-on scales or individual-wheel scales to determine the weight of the motor home.
What are some important safety considerations when driving my motor home?
Always wear seat belts when the motor home is in motion, make sure all loose exterior fixtures are secured, check tire inflation and lug nut tightness, inspect fluid levels, and close all lines and electrical cords before starting the engine.

Related manuals

Download PDF

advertisement