Catalogue Sheet: DEL Series

Catalogue Sheet: DEL Series
Project/Location:
DEL Series
Contractor:
Decorative 6, 12 and 24V
Thermoplastic Cube Units
Date:
Prepared by:
typical specifications
Features
• Impact-resistant steel center cabinet contains the battery
and charger
Supply and install a complete emergency lighting system as
described herein and shown on the drawings.
The Emergi-Lite® DEL Smart Diagnostic micro-controller board
shall supply the rated load for a minimum of 1/2 hour to 87.5% of the
rated battery voltage. The unit shall be rated 120V or 347V, 60 Hz and
be CSA listed.
The unit shall have an output of
V.
The charger shall be fully computer tested and its charge voltage
factory set to ± 1% tolerance. Chargers with field-adjusted
potentiometers are not acceptable. A pulse-type charger shall be
employed to promote long battery life and reduce the potential for
grid corrosion. The charger shall provide a continuous high charge
to recharge the battery, and when the battery is at full capacity,
the charger will shut off. Periodically the charger shall provide a
pulse of energy to keep the battery topped off. The charger shall
be current limited, temperature compensated, short-circuit proof
and reverse polarity protected. The unit shall be furnished with an
electronic lockout circuit, which will connect the battery when the
AC circuit is activated, and an electronic brownout circuit, which will
activate the emergency heads when utility power dips below 75%
of nominal voltage. A low voltage battery protection circuit shall
be provided and will disconnect the battery from the fused output
circuit at the end of discharge. The unit shall self-test for 1 minute
every 30 days, 10 minutes every 6 months and 30 minutes every 12
months. The unit shall be capable of full recharge in compliance
with CSA specifications. The unit shall be furnished with a sealed,
dust-tight relay, a test switch and diagnostic LED indicator lights to
continuously monitor the status of the unit: Battery Failure, Battery
Disconnected, Charger Failure, Lamp Failure, Service Alarm, AC
-“ON”, Charger High Rate. The unit shall come complete with fully
adjustable 12V or 24V/12W or 20W quartz halogen lamps. Each lamp
shall be housed in an impact-resistant polycarbonate cube. The cube
lens shall be frosted to diffuse light.
.
The unit shall be Emergi-Lite® model:
• Frosted, thermoplastic light cubes protect light modules
against vandalism while providing visual masking and light
diffusion
• Units can be wall or ceiling mounted
• Maintenance-free, sealed Lead-Calcium battery
• Fully automatic, solid-state charger with low voltage battery
disconnect, brownout protection, integral test switch and
LED AC-On pilot lights
• Also available as a remote fixture; see the Remote Fixtures
section of this catalogue
• CSA C22.2 No. 141 certified
• NEXUS® compatible
Wire guards
460.0097-E
Wall Mount or Ceiling Mount
REPLACEMENT LAMPS
IN the same family
EF26/EF26DS/EF26D SERIES
P. 151
ordering code
type
570.0016-E
Mini tungsten
voltage/ wattage
6V-9W
570.0025-E
Mini tungsten
12V-9W
570.0045-E
Mini tungsten
24V-9W
580.0097-E
MR16, LED
6V-4W
580.0093-E
MR16, LED
12V-4W
580.0098-E
MR16, LED
24V-4W
580.0100-E
MR16, LED
24V-6W
580.0104-E
MR16, LED
12V-5W
580.0095-E
MR16, LED
120V-4W
580.0106-E
MR16, LED
120V-4W
For the complete list, please see the lamp chart on pages 156 to 158
106
Project/Location:
DEL Series
Contractor:
Decorative 6, 12 and 24V
Thermoplastic Cube Units
Date:
Prepared by:
Dimensions
Dimensions are approximate and subject to change.
303/4” [78.1 cm]
43/4” [12.1 cm]
43/4” [12.1 cm]
41/2” [11.4 cm]
217/8” [55.6 cm]
POwer consumption and unit rating
model
wattage capacity
ac specs
30min
1h00
1h30
2h00
06DEL36
0.10/0.04 A
36
21
15
12
6
06DEL72
0.22/0.08 A
72
42
30
24
12
06DEL144
0.22/0.08 A
108
63
45
36
18
06DEL180
0.22/0.08 A
180
105
75
60
30
12DEL36
0.10/0.04 A
36
21
15
12
6
0.15/0.06 A
72
42
30
24
12
12DEL144
0.41/0.14 A
144
84
60
48
24
12DEL200
0.41/0.14 A
200
117
83
67
33
12DEL288
0.41/0.14 A
288
168
120
96
48
24DEL144
0.55/0.20 A
144
84
60
48
24
24DEL288
0.67/0.23 A
288
168
120
96
48
12DEL72
120/347VAC
4h00
ordering information
Series
capacity
06DEL=
6V
36= 36W
72= 72W
144= 144W
180= 180W
12DEL=
12V
36= 36W
72= 72W
144= 144W
200= 200W
288= 288W
24DEL=
24V
144= 144W
288= 288W
voltage
Blank=
120/347VAC input
-2= 277VACinput
# of
lamps
options
D= time delay
L= line cord 120V
LW= cord and twist-lock plug 120V
T= lamp disconnect
TB= DC terminal block
TP= tamper-proof screws
U= auto-diagnostics*
UN= auto-diagnostics, non-audible*
X2= remote test receiver**
690.0454-E= tamper-proof bit***
TX2= remote test transmitter
NEX= NEXUS® system interface****
NEXRF= w
ireless NEXUS® system
interface****
* Minimum lamp load required: 20% of unit
capacity
**Remote test transmitter needed.
***One bit per order.
****Not all options available with the Nexus®
system. Please consult your sales
representative.
EXAMPLE: 06DEL36U/2
107
/2= two
lamps
lamp style/wattage
Blank= tungsten, 6V, 12V, 24V-9W, wedge base
-18= tungsten, 12V, 24V-18W, wedge base
MI= MR16, 6V-6W
MJ= MR16, 6V-10W
MK= MR16, 12V-12W
MA= MR16, 12V-20W
MB= MR16, 12V-35W
MC= MR16, 12V-50W
MS= MR16, 24V-12W
MD= MR16, 24V-20W
ME= MR16, 24V-35W
MF= MR16, 24V-50W
Q= halogen, 6V, 12V-8W, quartz bi-pin
Q12= halogen, 6V, 12V-12W, quartz bi-pin
Q20= mini halogen, 6V,12V, 24V-20W, quartz bi-pin
LA= MR16 LED, 6V-4W
LG= MR16 LED, 12V-4W
LI= MR16 LED, 12V-5W
LL= MR16 LED, 24V-4W
LM= MR16 LED, 24V-6W
LJ= MR16 LED, 12V-6W
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement