- Computers & electronics
- TVs & monitors
- LCD TVs
- Austin Hughes Electronics
- UltraView HOP-17
- User manual
advertisement
dedicated LCD display solutions
User Manual
17” High Brightness LCD
HAP-17
Front NEMA4 / IP65
HOP-17
Universal Mounting Open Frame
Designed and manufactured by Austin Hughes
UM-UV-621-H17-Q215V1 www.austin-hughes.com
Legal Information
First English printing, October 2002
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. We are not liable for any injury or loss that results from the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for future reference.
■
Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
■
Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
■
When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing
damage to other equipment or injury to persons nearby.
■
When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the
power supply. Proper air convection is necessary to keep it from overheating.
■
Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
■
If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current
labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed
on the equipment’s ratings label.
■
Observe all precautions and warnings attached to the equipment.
■
If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being
damaged by transient over-voltage.
■
Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fi re or electrical shock.
■
Only qualifi ed service personnel should open the chassis. Opening it yourself could damage the equipment and
invalidate its warranty.
■
If any part of the equipment becomes damaged or stops functioning, have it checked by qualifi ed service personnel.
What the warranty does not cover
■
Any product, on which the serial number has been defaced, modifi ed or removed.
■
Damage, deterioration or malfunction resulting from:
□
Accident, misuse, neglect, fi re, water, lightning, or other acts of nature, unauthorized product modifi cation, or failure to follow instructions supplied with the product.
□
Repair or attempted repair by anyone not authorized by us.
□
Any damage of the product due to shipment.
Removal or installation of the product.
□
Causes external to the product, such as electric power fl uctuation or failure.
Use of supplies or parts not meeting our specifi cations.
□
Normal wear and tear.
Any other causes which does not relate to a product defect.
■
Removal, installation, and set-up service charges.
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifi cations made to this equipment may void the user’s authority to operate this equipment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
■
Re-position or relocate the receiving antenna.
■
Increase the separation between the equipment and receiver.
■
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
UM-UV-621-H17-Q215V1 www.austin-hughes.com
Contents
< Part. 1 >
HAP-17
1.1
1.2
1.3
Package Content
Structure Diagram & Dimension
Mounting Hardware & Installation
< Part. 2 >
HOP-17
2.1
2.2
2.3
Package Content
Structure Diagram & Dimension
Mounting Hardware & Installation
< Part. 3 >
Specifi cations / OSD
3.1
3.2
Product Specifi cations
On-screen Display Operation ( OSD )
< Part. 4 >
Options
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
Option Table
MCS
Multi-display control solution
AV2.2D
Upgrade : DVI-D, S-Video + BNC & Audio
AV2.2H
Upgrade : HDMI, S-Video + BNC & Audio
Projected Capacitive ( 4-point touch )
Resistive / Capacitive ( single point touch )
DC Power : 24V / 48V / 110 ~ 125V
MIL-type or lockable connector
Quad display for CCTV
TV ( Analog )
Auto / switch dimming
P.1
P.2 - 3
P.4 - 5
P.6
P.7 - 8
P.9
P.10 - 11
P.12
P.13
P.14
P.15 - 16
P.17 - 18
P.18
P.19
P.20
P.21 - 22
P.23
UM-UV-621-H17-Q215V1 www.austin-hughes.com
Before Installation
■
It is very important to mount the equipment in a suitable cabinet or on a stable surface.
■
Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
Unpacking
The equipment comes with the standard parts shown in package content. Check and make sure they are included and in good condition. If anything is missing, or damaged, contact the supplier immediately.
How To Clean Your LCD Monitor
Caution :
■
To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or
plugging your monitor into an electrical outlet.
■
When you clean your monitor, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your display. Pressure damage is not covered under warranty.
■
Use only cleansers made specifi cally for cleaning monitors and monitor screens. Cleansers not made to
clean monitors and monitor screens can scratch the LCD display or strip off the fi nish.
■
Do not spray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly
onto the screen or case can cause damage which is not covered under warranty.
■
Do not use paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood based
paper product such as paper towels can scratch your LCD screen.
Cleaning Your Monitor
To clean your LCD safely, please follow these steps :
Disconnect the power cord.
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, please follow these steps :
1 Disconnect the power cord.
Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your microfi ber cloth fi rst, not directly on the parts you are cleaning.
UM-UV-621-H17-Q215V1 www.austin-hughes.com
< Part 1 >
< 1.1 > Package Content - HAP-17
17" High Brightness LCD Display
HAP-17
17" High Brightness LCD display X 1
6ft VGA cable X 1
Power adapter X 1
Power cord X 1
Mounting hardware X 1 pack
- Mounting bracket x 4 pcs
- M4* 6mm screw x 8 pcs
- M4* 50mm screw x 8 pcs
Basic I/O
Power DVI-D VGA
AV2.2D upgrade I/O
Power BNC S-Video
Audio out - in - in
Video PC
DVI-D VGA
AV2.2H upgrade I/O
Power BNC S-Video
Audio out - in - in
Video PC
HDMI
VGA
< 1.2 > Structure Diagram - HAP-17
1
2
3
4
1
Rear case
2
LCD panel
3
Protective 3mm glass
4
6mm aluminum front bazel
5
6
Audio speaker ( for HDMI, Audio or TV option )
LCD membrane
7
Remote sensor
Front view
HAP-17
7
Rear view
5
6
Model
HAP-17
Product Dimension
(W x D x H)
439 x 64.2 x 356.6 mm
17.3 x 2.5 x 14 inch
Packing Dimension
(W x D x H)
615 x 113 x 523 mm
25.6 x 4.9 x 23.5 inch
Net
Weight
6.6 kg
14.5 lbs
Gross
Weight
9.2 kg
20.2 lbs
< 1.2 > Dimension - HAP-17
Front View
HAP-17
17” High Brightness LCD Display
Side View
Rear View
UNIT : mm
1mm = 0.03937 inch
Bottom View
< 1.3 > Mounting Hardware - HAP-17
1
Mounting bracket x 4 pcs
2 M4*6mm screw x 8 pcs
Hardware set part no. UV-BK#2
3 M4*50mm screw x 8 pcs
Steps
■
Install 4 mounting brackets with 8 x M4*6mm screws
■
Adjust the LCD panel with 8 x M4*50mm screws and fi x it on the surface.
< 1.3 > Installation - HAP-17
17” High Brightness LCD Display
M4 screw
VESA mount ( 100*100mm )
■
Hardware and M4*4 pcs for VESA mount are not provided
< Part 2 >
< 2.1 > Package Content - HOP-17
HOP-17
17” High Brightness LCD display X 1
6ft VGA cable X 1
Power adapter X 1
Power cord X 1
Basic I/O
Power DVI-D VGA
AV2.2D upgrade I/O
Power BNC S-Video
Audio out - in - in
Video PC
DVI-D VGA
AV2.2H upgrade I/O
Power BNC S-Video
Audio out - in - in
Video PC
HDMI
VGA
< 2.2 > Structure Diagram - HOP-17
1
2
17” High Brightness LCD Display
Front view
OP-17
3
6
Rear view
1
Rear case
LCD panel
Audio speaker ( for HDMI, Audio or TV option )
Universal open frame mounting
LCD membrane
Extended remote sensor membrane cable
( 66cm from AD board to sensor end )
4
5
Model
HOP-17
Product Dimension
(W x D x H)
436 x 58.2 x 353.6 mm
17.2 x 2.3 x 13.9 inch
Packing Dimension
(W x D x H)
615 x 113 x 523 mm
24.2 x 4.4 x 20.6 inch
Net
Weight
4.9 kg
10.8 lbs
Gross
Weight
7.5 kg
16.5 lbs
< 2.2 > Dimension - HOP-17
Front View
HOP-17
Side View
Rear View
UNIT : mm
1mm = 0.03937 inch
Bottom View
< 2.3 > Installation - HOP-17
( I ) Universal mount
17” High Brightness LCD Display
( II ) VESA mount ( 100*100mm )
M4 screw
Hardware and M4*4 pcs for VESA mounting are not provided
< Part 3 >
< 3.1 > Product Specifi cations
Mechanical
Design
LCD
Panel
Front Panel
Rear Casing
VESA Mounting
Other Mounting
Protection
Panel Size ( diagonal )
Display pixel ( dots x lines )
Brightness ( typ. )
Contrast Ratio ( typ. )
Color
Viewing Angle ( L/R/U/D )
Response Time ( ms )
Dot pitch ( mm )
Display Area ( mm )
Surface treatment
Surface hardness
Backlight Type
MTBF ( hrs )
HAP-17
Black, RAL 9005
Black, RAL 9005
100 x 100mm
Panel mount
3mm protective glass
17-inch TFT color LCD
1280 x 1024
1000
1000:1
16.7 M
85/85/80/80
5
0.264
337.92H x 270.33V
Anti-glare
3H
LED
50,000
HOP-17
-
Black, RAL 9005
100 x 100mm
Universal mount
-
Video
Connectivity
Analog VGA Analog 0.7Vp-p
Power Power Supply
Power Consumption
Range
Screen display ON
Auto-sensing 100 to 240VAC,
50/60Hz
35W or less
Power saving mode 4W or less
Power button OFF 1W or less
Regulatory Safety
Environmental
Environmental
Conditions
Operating
Storage
FCC & CE certifi ed
RoHS2 & REACH compliant
Temperature
Humidity
Temperature
Humidity
Shock
Vibration
0 to 55°C degree
20~90%, non-condensing
-5 to 60°C degree
5~90%, non-condensing
10G acceleration (11ms duration)
5~500Hz 1G RMS random
Physical
Specifi cation
Applicable
Format
Product ( W x D x H )
Packing ( W x D x H )
Net Weight
Gross Weight
VGA Input
17” High Brightness LCD Display
HAP-17
439 x 64.2 x 356.6 mm
17.3 x 2.5 x 14 inch
615 x 113 x 523 mm
24.2 x 4.4 x 20.6 inch
6.6 kgs / 14.5 lbs
9.2 kgs / 20.2 lbs
HOP-17
436 x 58.2 x 353.6 mm
17.2 x 2.3 x 13.9 inch
615 x 113 x 523 mm
24.2 x 4.4 x 20.6 inch
4.9 kgs / 10.8 lbs
7.5 kgs / 16.5 lbs
PC Signal 1280 x 1024 x 60 / 75Hz
1280 x 960 x 60Hz
1280 x 760 x 60 / 75Hz
1152 x 864 x 75Hz
1024 x 768 x 60 / 70 / 75Hz
848 x 480 x 60Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
640 x 400 x 70Hz
640 x 350 x 70Hz
< 3.2 > On-screen Display Operation ( OSD )
Power light
Green = On
Orange = Power saving
Membrane Switch Function
Power on / off LCD
Display the OSD menu
Scrolls through menu options and adjusts the displayed control
(To auto adjustment by pressing the button for 5 seconds)
Exit the OSD screen
Toggle analog, digital & video connection (DVI-D and video options only)
OSD Confi guration Page
Image: for the brightness, contrast, color temp, red, green, and blue
Geometry: for the auto adjust, H position, V position, phase and clock
Video: for the colour, tint, sharpness, noise reduction, DCDi and TV Setup
Audio: for volume, bass, treble, balance, AVL and mute
Misc: for the language, OSD position, graphic mode, ratio, reset and timer
< Part 4 > Options
17” High Brightness LCD Display
< 4.1 > Option Table
Options
HDMI * or DVI-D
S-Video * + Composite ( BNC )
Audio
Touchscreen
MCS multi-display control ***
DC Power
MIL-type / lockable connector
Quad display
TV ( Analog ) *
Auto / switch dimming
HAP
*
About HDMI and DVI-D
( 1 ) For AV2.2 upgrade, either HDMI or DVI-D is provided.
*
Remote Controller
( 1 ) AV2.2 upgrade comes with RC-1 remote controller.
( 2 ) TV option comes with RC-2 remote controller.
HOP
< 4.2 > Options : MCS ( Multi-display Control )
More control is always good. Especially when it is necessary and easy. Austin Hughes provides MCS solution to control the OSD of various UltraView LCD display up to 64 units.
The RS-232C is used for the communication between the PC and the fi rst display via a 15 feet serial cable while the CAN bus is used for the various LCD displays cascade together via CAT 5/6 cable, and daisy chain up to 1,000 meters.
Designed for use with UltraView LCD displays, Austin Hughes provides a MCS input module without using additional space or power and it comes standard with a 2-year warranty.
Power BNC S-Video
Audio
DVI-D VGA
HDMI out - in - in
Video PC set
***
Please download the protocol of MCS control at :
http://www.austin-hughes.com/support/usermanual/ultraview/UM-UV-MCS.pdf out
MCS
in Link
RS-232C
15 feet serial cable
( over 15 feet, extender required )
Set switch
For the 1st and last display, push the set switch upward
For other daisy chain displays, push the set switch downward
RJ-45 jack
LINK OUT
Cat5 / 6 cable max. 300 meters
IN OUT IN
Cat5 / 6 cable max. 300 meters
OUT
Cat5 / 6 cable max. 300 meters
IN OUT
Daisy chain up to 1,000 meters and 64 displays up to 64 displays
< 4.3 > Options :
17” High Brightness LCD Display
AV2.2D Upgrade Options
- DVI-D ( DVI-D TMDS single link )
- AV ( S-Video + Composite, BNC )
- Audio ( 3.5mm audio jacks for audio in & out, and 2W + 2W speakers )
Power BNC S-Video
Audio out - in - in
Video PC
DVI-D VGA
AV2.2H Upgrade Options
- HDMI ( HDMI 1.1, CEA-861-D )
- AV ( S-Video + Composite, BNC )
- Audio ( 3.5mm audio jacks for audio in & out, and 2W + 2W speakers )
Power BNC S-Video
Audio
HDMI out - in - in
Video PC
VGA
***
AV2.2 upgrade option comes with RC-1 remote controller x 1.
How to Use RC-1 Remote Controller
1
2
3
4
1
2
3
POWER
MUTE
INPUT
4
5
6
7
8
9
0- 9
V + / -
CH + / -
MENU
AUTO
- / -
5
6
7
Switches on or off the TV
Turn on or off the speaker
Switch to signal input mode
Select channels. For channel numbers 10 and above, enter the second digit within two seconds.
Increase or decrease the speaker volume
Increase or decrease the channel number
Display the menu on the screen or go to the previous menu
For auto searching
For setting one or two input digit
8
9
< 4.4 > Options : Touchscreen & driver
17” High Brightness LCD Display
H17" USB Touchscreen Specifi cation
Model
Technology
Touch Point
Input Type
Resolution
Touch Point Accuracy
Response Speed
Activation Force
Surface Hardness
Light Transmission
Haze
Durability
Top Layer
Bottom Layer
Thickness
Connector
Compatibility
TPC-17 Multi-touch
Projected Capacitive
4
Finger or Capacitive Stylus
2048 x 2048
± 10 mm offset
Max. 20 ms
≤ 10 g
7H
≥ 88%
≤ 2%
> 100 million touches
1.8 mm Tempered Glass
Film
2.2 mm
USB Type A
Windows 7
TRB e-Resistive TCB e-Capacitive
5-Wire Resistive
Single
Finger or Stylus
2048 x 2048
-
Capacitive
Single
Finger
2048 x 2048
-
15 ms
≤ 50 g
3H
80% ± 3%
8% ± 3%
10 million touches
ITO Film
ITO Glass
2.2 ± 0.2 mm
20 ms
≤ 50 g
9H
92% ± 2%
7%
300 million touches
Glass
2.8 mm ± 10%
USB Type A USB Type A
Windows 7 / XP / Vista, Linux
■
Dimension will be changed if Multi-touch required
■
USB touchscreen package includes 1 x 6ft USB cable, quick reference guideline and CD disc
■
For detailed information, please refer to the attached CD disc
■
As the touchscreen unit is not made of toughened glass, please handle it carefully
Power
USB Touchscreen
DVI-D VGA
< 4.4 > Options : Touchscreen & driver
TPC-17 Driver
Connect the USB cable from the USB port on the LCD to a computer. The touch screen supports easy Plug-and-Play operations. There is no need to install additional drivers on the computer.
TRB / TCB Driver
Please follow the below steps to setup the touch screen:-
Step 1. Run the bundled CD disc or download the driver from the link below :
http://www.austin-hughes.com/downloads/UVDL/driver.html
Step 2. Double click the Setup.exe
Step 3.
Follow the installation instruction to fi nish the setup
Step 4.
After installation, run the TouchKit program & the “4 point calibration”
Please do the initial calibration after the fi rst setup
< 4.5 > Options : DC Power
Model
Input rating
Input voltage:
Input range:
Input current
- No load
- Full load
Output rating
Output voltage:
Output current:
Effi ciency
24V
24-Volt
18 ~ 36V
50 mA
4880 mA
12-Volt
4.16A
85%
48V
48-Volt
36 ~ 75V
50 mA
2442 mA
12-Volt
4.16A
85%
110 ~ 125V
110-Volt
66 ~ 160V
40 mA
993 mA
12-Volt
8.4A
92%
< 4.6 > Options : MIL-type or Lockable Connector
17” High Brightness LCD Display
MIL - type
Connector
Lockable
Connector
Input
DC Power
***
( Male )
Part no.
MS3470W8-33P
VGA
***
( Male )
MS3470W14-15P
MIL Standard
MIL - DTL - 26482
MIL - DTL - 26482
***
There are several additional MIL DC and VGA connector types with varying design
characteristics to meet cost considerations and to provide users with the most
design fl exibility possible. For more information, please contact us.
Input
DC Power
( Male )
Part no.
YM-Ext-461CP001
Standard
D-type 3W3
USB LUSB - A111 - 00 -
***
MIL - type or Lockable connectors above can be integrated with our LCD displays.
Sale service just for connectors not provided.
< 4.7 > Options : Quad Display
QD Specifi cation
Item Description
Model Number
Number of Color
Imaging System
Resolution
Refresh Rate
Video Input
Video Output
Camera Input
VCR Input
Live Monitor
Loop Through Out
Auto Gain Control
VCR Output
Time / Date
On Screen Display
Camera Title
Display Format
2 x Zoom On
Playback
QUAD
FULL
SEQUENCY
Dwell Time
Alarm Inputs
Relay Outputs
Alarm Hold Time
Built-in Buzzer
Key Lock
QD (NTSC)
16.7 M
NTSC
1024 x 525
60
1.0 Vpp, 75 Ohm x 4
1.0 Vpp, 75 Ohm x 1
1.0 Vpp, 75 Ohm x 1
1.0 Vpp, 75 Ohm x 4
1.0 Vpp, 75 Ohm x 1
Yes
Yes
Yes
8 Character Title
Yes
Yes
Yes
Yes
0 to 99 Sec Adjustable
Selectable NO/NC Contacts x 4
NO/NC contacts x 1: 1A @DC24V Max.
1 Sec to Non-stop
Yes
Yes
QD (PAL)
16.7 M
PAL
1024 x 625
50
***
For QD option, casing dimensions will be changed.
< 4.8 > Options : TV ( Analog )
17” High Brightness LCD Display
Power BNC S-Video
Audio
HDMI out - in - in
Video PC
VGA
TV
***
For TV option :
( 1 ) The AD board comes standard with HDMI, VGA, S-Video, BNC, audio inputs and
RC-2 remote controller.
( 2 ) Casing dimensions will be changed.
How to Use RC-2 Remote Controller
1
2
3
4
INPUT MUTE
VOL
1 2 3
4 5 6
7 8 9
AUTO
0
-/--
CH
FREEZE
MENU SELECT ASPECT
9
10
5
6
7
20
21
ENTER SLEEP
BACK EXIT PIP
SOURCE
SWAP
PIP
POSITION
PIP
AUDIO
13
15
16
17
19
Water proof
3
4
5
1
2
6
7
8
9
10
11
12
13
14
15
16
0 - 9
AUTO
MENU
BACK
MUTE
Vol + / -
CH + / -
FREEZE
- / --
ASPECT
SELECT
SLEEP
EXIT
INPUT
▲ / ▼ / ◄ / ► / ENTER
Select the source
Switches on or off the TV
Only use in TV mode. Select channels. For channel numbers 10 and above, enter the second digit within two seconds.
Auto adjust
Display the menu on the screen or go to the previous menu
Go to the upper menu or select the previous value /
Go to the next menu or select the next value /
Decrease the setting value /
Increase the setting value or enter to the select item setting
Enter to the select item settings or excude the setting
Back to previous value
Turn on or off the speaker
Increase or decrease the speaker volume
For TV model only, increase or decrease the channel number
Reserve for OEM model
For setting input single or double digits
Adjust the screen size
To select the existing item
Select the sleeping time
Exit the menu or cancel
17
18
19
20
21
PIP functions
PIP
PIP AUDIO
POSITION
SOURCE
SWAP
Picture in picture
To set the audio of in PIP mode
To set the screen position in PIP mode
PIP Source
Swap screen in PIP mode
< 4.9 > Options : Auto Dimming
17” High Brightness LCD Display
2
1
1 DA-01 Light sensor on OP model
( 66cm from AD board to sensor end )
2 DA-01 Light sensor on AP model
DA-01 light sensor will be installed on the display front panel when auto dimming is ON in OSD menu. Then the brightness of display is changed according to its environmental brightness.
Once the auto dimming is ON, users cannot adjust brightness in OSD.
Steps : OSD Menu > Picture > Auto Dimming > ON
Light Sensor Operation Range
[cd/m²]
1,000
800
[v]
600
200
10
0 1 100 500 2,000 [lx]
Options : Switch Dimming
DS-01 is a IP54 dimming knob installed on the right bottom side of the front panel. The display can support hyper dimming function to adjust brightness from nearly 0% to 100% via a easy-to-use knob.
H
DS-01 dimming knob
Dimensions ( W x H ) : 15.5 x 14.2 mm
W
***
- For this option, front panel and casing dimensions may be changed.
- For HAP series, if DS-01 dimming knob applied, IP protection will be
downgraded from IP65 to IP54.
The company reserves the right to modify product specifi cations without prior notice and assumes no responsibility for any error which may appear in this publication.
All brand names, logo and registered trademarks are properties of their respective owners.
Copyright 2015 Austin Hughes Electronics Ltd. All rights reserved.
UM-UV-621-H17-Q215V1 www.austin-hughes.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project