313-855m
Table of Contents
End-Wheel, No-Till Drill
706/1006NT
313-855M
Operator’s Manual
ORIGINAL INSTRUCTIONS
Read the Operator’s Manual entirely. When you
see this symbol, the subsequent instructions and
warnings are serious - follow without exception.
Your life and the lives of others depend on it!
Illustrations may show optional
equipment not supplied with standard
unit.
© Copyright 2015
Printed 2015-08-04
Cover
Table of Contents
Important Safety Information...................................... 1
Safety Decals................................................................. 5
Introduction ................................................................ 11
Description of Unit........................................................ 11
Intended Usage............................................................ 11
Models Covered ....................................................... 11
Using This Manual ....................................................... 11
Owner Assistance ........................................................ 12
Further Assistance ....................................................... 12
Preparation and Setup............................................... 13
Prestart Checklist......................................................... 13
Hitching Tractor to Drill ................................................ 13
Hitch Assembly ........................................................ 13
Hitch Height ............................................................. 14
Hitching to Tractor.................................................... 14
Hydraulic Hose Hookup ............................................... 15
Rephasing Cylinders.................................................... 15
Bleeding Hydraulics ..................................................... 16
Leveling Drill ................................................................ 17
Operating Instructions .............................................. 18
Prestart Checklist......................................................... 18
Field Operation ............................................................ 18
Opener Operation .................................................... 19
Transporting................................................................. 19
Cylinder Locks ......................................................... 19
Unload Drill Box ....................................................... 19
Clearance................................................................. 19
Road Rules .............................................................. 19
Lock-out Hub............................................................ 20
Parking .........................................................................20
Adjustments................................................................21
Coulter Adjustments .....................................................21
Coulter Depth Control ...............................................21
Coulter Down Pressure ................................................22
Opener Adjustments.....................................................23
Opener Seeding Depth.................................................23
Gauge Wheel Idler Adjustment.....................................24
Drive Clutch ..................................................................24
Drive Train Operation ...................................................25
Spring Tine Harrow.......................................................26
Troubleshooting .........................................................27
Maintenance and Lubrication....................................29
Maintenance .................................................................29
Storage .........................................................................29
Lubrication and Scheduled Maintenance .....................30
Options ........................................................................34
Appendix .....................................................................37
Torque Values Chart ....................................................37
Specifications and Capacities.......................................38
Hydraulic Schematics ...................................................38
Seed Box Sprocket Configuration ................................39
Seed Box Agitator Sprocket Configuration ...................39
Small Grass Seeds Sprocket Configuration ................40
Native Grass Sprocket Configuration ...........................40
Fertilizer Sprocket Configuration .................................41
Fertilizer with Small Grass Seeds Box
Sprocket Configuration .................................................41
© Copyright 2011, 2015 All rights Reserved
Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation
of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the
information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product
at the time of its publication, and may not reflect the product in the future.
Registered Trademarks of Great Plains Manufacturing, Inc. include:
Clear-Shot, Great Plains, Land Pride, Seed-Lok, Solid Stand.
Brand and Product Names that appear and are owned by others are trademarks of their respective owners. QR Code® is a registered trademark of Denso Wave, Inc.
Printed in the United States of America
II
706/1006NT  313-855M
2015-08-04
Table of Contents
Important Safety Information
Look for Safety Symbol
The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert and carefully read the message that
follows it. In addition to design and configuration of
equipment, hazard control and accident prevention are
dependent upon the awareness, concern, prudence and
proper training of personnel involved in the operation,
transport, maintenance and storage of equipment.
Be Aware of Signal Words
Signal words designate a degree or level of hazard
seriousness.
DANGER, and the color Safety Red, indicate an
imminent hazard which, if not avoided, will result in death
or serious injury. This signal word is limited to the most
extreme situations, typically for machine components
that, for functional purposes, cannot be guarded.
WARNING, and the color Safety Orange, indicate a
potential hazard which, if not avoided, could result in
death or serious injury, and includes hazards that are
exposed when guards are removed. It may also be used
to alert against unsafe practices.
CAUTION, and the color Safety Yellow, indicate a
potential hazard which, if not avoided, may result in
minor or moderate injury. It may also be used to alert
against unsafe practices.
Prepare for Emergencies
▲ Be prepared if a fire starts
▲ Keep a first aid kit and fire extinguisher handy.
▲ Keep emergency numbers for doctor, ambulance, hospital
and fire department near phone.
Be Familiar with Safety Decals
▲ Read and understand “Safety Decals” on page 5,
thoroughly.
▲ Read all instructions noted on the decals.
▲ Keep decals clean. Replace damaged, faded and illegible
decals.
2015-08-04
Parts Manual QR Locator
Dealer QR Locator
The QR Code® (Quick Reference) on
the front cover and to the left will take
you to the Parts Manual for this
equipment. Download the appropriate
App on your smart phone, open the
App, point your phone on the
QR Code®and take a picture.
The QR Code® at left will link you to
available dealers for Land Pride
products. Refer to Parts Manual QR
Locator for detailed instructions.
706/1006NT  313-855M
1
Important Safety Information
Table of Contents
Wear Protective Equipment
▲ Wear protective clothing and equipment.
▲ Wear clothing and equipment appropriate for the job. Avoid
loose-fitting clothing.
▲ Because prolonged exposure to loud noise can cause
hearing impairment or hearing loss, wear suitable hearing
protection such as earmuffs or earplugs.
▲ Because operating equipment safely requires your full
attention, avoid wearing entertainment headphones while
operating machinery.
Handle Chemicals Properly
Agricultural chemicals can be dangerous. Improper use
can seriously injure persons, animals, plants, soil and
property.
▲ Do not use liquid seed treatments with the drill.
▲ Read and follow chemical manufacturer’s instructions.
▲ Wear protective clothing.
▲ Handle all chemicals with care.
▲ Avoid inhaling smoke from any type of chemical fire.
▲ Never drain, rinse or wash dispensers within 100 feet (30m)
of a freshwater source, nor at a car wash.
▲ Store or dispose of unused chemicals as specified by
chemical manufacturer.
▲ Dispose of empty chemical containers properly. Laws
generally require power rinsing or rinsing three times,
followed by perforation of the container to prevent re-use.
Avoid High Pressure Fluids
Escaping fluid under pressure can penetrate the skin,
causing serious injury.
▲ Avoid the hazard by relieving pressure before disconnecting
hydraulic lines.
▲ Use a piece of paper or cardboard, NOT BODY PARTS, to
check for suspected leaks.
▲ Wear protective gloves and safety glasses or goggles when
working with hydraulic systems.
▲ If an accident occurs, seek immediate medical attention
from a physician familiar with this type of injury.
Keep Riders Off Machinery
Riders obstruct the operator’s view. Riders could be
struck by foreign objects or thrown from the machine.
▲ Never allow children to operate equipment.
▲ Keep all bystanders away from machine during operation.
2
706/1006NT  313-855M
2015-08-04
Important Safety Information
Table of Contents
Use Safety Lights and Devices
Slow-moving tractors and towed implements can create
a hazard when driven on public roads. They are difficult
to see, especially at night.
▲ Use flashing warning lights and turn signals whenever
driving on public roads.
▲ Use lights and devices provided with implement
Transport Machinery Safely
Maximum transport speed for implement is 20 mph
(30 kph). Some rough terrains require a slower speed.
Sudden braking can cause a towed load to swerve and
upset.
▲ Do not exceed 20 mph (30 kph). Never travel at a speed
which does not allow adequate control of steering and
stopping. Reduce speed if drill is not equipped with brakes.
▲ Comply with state and local laws.
▲ Carry reflectors or flags to mark drill in case of breakdown
on the road.
▲ Semi-mounted and 3-point implements reduce weight on
steering tires. Verify that tractor is correctly ballasted.
Watch for signs of poor steering traction.
Tires Not a Step
Do not use gauge wheel or lift-assist tires as steps. A tire
could spin underfoot, resulting in a fall onto the
implement or ground, possibly causing serious injury.
▲ The gauge wheel tires can be in poor ground contact at any
time, even with the drill lowered in the field. They can
appear to be in ground contact, and spin easily, in multiple
conditions.
▲ The lift-assist tires can be in poor ground contact, or out of
ground contact, whenever the drill is lowered.
Shutdown and Storage
▲ Park on level ground.
▲ Unhitch and store the drill in an area where children
normally do not play.
Tire Safety
Tire changing can be dangerous and should be
performed by trained personnel using correct tools and
equipment.
▲ When inflating tires, use a clip-on chuck and extension hose
long enough for you to stand to one side–not in front of or
over tire assembly. Use a safety cage if available.
▲ When removing and installing wheels, use wheel-handling
equipment adequate for weight involved.
2015-08-04
706/1006NT  313-855M
3
Important Safety Information
Table of Contents
Practice Safe Maintenance
▲ Understand procedure before doing work. Use proper
tools and equipment. Refer to this manual.
▲ Work in a clean, dry area.
▲ Lower the drill, put tractor in park, turn off engine, and
remove key before performing maintenance. If work must
be performed with implement raised, use blocks or
jackstands rated for the drill weight.
▲ Make sure all moving parts have stopped and all system
pressure is relieved.
▲ Allow drill to cool completely.
▲ Disconnect battery ground cable (-) before servicing or
adjusting electrical systems.
▲ Welding: Disconnect battery ground. Avoid fumes from
heated paint.
▲ Inspect all parts. Make sure parts are in good condition
and installed properly.
▲ Remove buildup of grease, oil or debris.
▲ Remove all tools and unused parts from drill before
operation.
Safety At All Times
Thoroughly read and understand the instructions in this
manual before operation. Read all instructions noted on
the safety decals.
▲ Be familiar with all drill functions.
▲ Operate machinery from the driver’s seat only.
▲ Do not leave drill unattended with tractor engine running.
▲ Do not stand between the moving tractor and drill during
hitching.
▲ Keep hands, feet and clothing away from power-driven
parts.
▲ Wear snug-fitting clothing to avoid entanglement with
moving parts.
▲ Make sure all persons are clear of working area.
4
706/1006NT  313-855M
2015-08-04
Important Safety Information
Table of Contents
Safety Decals
Safety Reflectors and Decals
Your implement comes equipped with all lights, safety
reflectors and decals in place. They were designed to
help you safely operate your implement.
✟ Read and follow decal directions.
To install new decals:
1. Clean the area on which the decal is to be placed.
2. Peel backing from decal. Press firmly on surface,
being careful not to cause air bubbles under decal.
✟ Keep lights in operating condition.
✟ Keep all safety decals clean and legible.
✟ Replace all damaged or missing decals. Order new decals
from your Land Pride dealer. Refer to this section for
proper decal placement.
✟ When ordering new parts or components, also request
corresponding safety decals.
Reflector: Slow Moving Vehicle (SMV)
32686
818-055C
On top of lift assist pivot weldment;
1 total
See “Transporting” on page 19.
Reflectors: Red
32686
838-266C
On rear face of lift assist cross tube, outside daytime
reflectors;
2 total
See “Transporting” on page 19.
Reflectors: Amber
838-266C
On side frames at walkboard ends,
on front face of lower front tool bars, outside ends;
4 total
32686
See “Transporting” on page 19.
2015-08-04
706/1006NT  313-855M
5
Important Safety Information
Table of Contents
Reflectors: Daytime
32686
838-267C
On rear face of lift assist cross tube, inside red reflectors;
2 total
See “Transporting” on page 19.
Danger: Moving Chain (Option)
32763
818-518C
CAUTION
MOVING CHAIN HAZARD
To prevent serious injury from moving chain:
DO NOT operate with enclosure missing
818-518C REV. B
Dual Seed: On outside of box end wall, under both
covers;
2 total
Danger: Moving Chain (Option)
32760
818-518C
CAUTION
MOVING CHAIN HAZARD
To prevent serious injury from moving chain:
DO NOT operate with enclosure missing
818-518C REV. B
Native Grass: On outside of box end wall, under both
covers;
2 total
Danger: Moving Chain (Option)
32610
818-518C
CAUTION
MOVING CHAIN HAZARD
To prevent serious injury from moving chain:
DO NOT operate with enclosure missing
818-518C REV. B
Small Seeds: On chain guard of Small Seeds option;
1 total
6
706/1006NT  313-855M
2015-08-04
Important Safety Information
Table of Contents
Danger: Hitch Crush
818-590C
On front faces of both lower 3-point hitch arms;
2 total
32686
See “Hitching Tractor to Drill” on page 13.
Danger: Possible Chemical Hazard
838-467C
Under lid of Small Seeds box;
1 total
32761
See “Coulter Down Pressure” on page 22.
Warning: Speed
818-337C
On front face of lower front cross tube inside 3-point
hitch;
1 total
32686
See “Transporting” on page 19.
Warning: Transport Locks
32686
838-057C
WARNING
CRUSHING HAZARD
To Avoid Serious Injury or Death,
Install Transport Locks:
Before Performing Maintenance.
Before Adjusting Drill.
Before Transporting.
838-057C REV .
On left face of lift assist mount weldment;
1 total
2015-08-04
706/1006NT  313-855M
7
Important Safety Information
Table of Contents
Warning: High Pressure Fluid
838-094C
On front face of right 3-point hitch arm;
1 total
See “Hitching Tractor to Drill” on page 13.
32686
Warning: Falling Hazard
838-102C
WARNING
To avoid serious injury or death:
Watch your step when climbing ladder or
walking on walkboard.
838-102C
On left side frame at ladder;
1 total
32686
See “Coulter Down Pressure” on page 22.
Warning: Hand Crush (Option)
32763
838-611C
Dual Seed: Under lid;
1 total
See “Hitching Tractor to Drill” on page 13.
Warning: Hand Crush (Option)
838-611C
To
bo pr
x ev
ad en
g it t
at da
no
or ma
t
g
tr
an e
an
d to
sp
it s t
or
h
83
t
dr e N
8dr
iv e a t
42
8C
b o ill w
c o iv e
x
i
mp Gr
lo t h
on as
ad Na
en s
ed ti
ts
v
:
w it e
h Gra
se ss
ed
.
Do
32760
Native Grass: Under lid;
2 total
See “Hitching Tractor to Drill” on page 13.
8
706/1006NT  313-855M
2015-08-04
Important Safety Information
Table of Contents
Warning: Moving Parts
818-860C
On front face of upper front cross tube at gearbox;
1 total
32686
Caution: Tires Not A Step
818-398C
On outside face of caster arms above tires;
2 total
32686
See “Tires Not a Step” on page 3.
Caution: General
818-719C
On front face of left 3-point hitch arm;
1 total
See “Important Safety Information” on page 1.
32686
Caution: Tire Pressure and Torque
838-092C
On rim of each lift assist wheel;
2 total
2015-08-04
32686
706/1006NT  313-855M
9
Important Safety Information
Table of Contents
Caution: Transport Locks
32686
848-339C
On top face of caster cross tube;
2 total
10
706/1006NT  313-855M
2015-08-04
Table of Contents
Introduction
Land Pride welcomes you to its growing family of new
product owners. Your drill has been designed with care
and built by skilled workers using quality materials.
Proper setup, maintenance, and safe operating practices
will help you get years of satisfactory use from the
machine.
Description of Unit
The 706/1006NT is a grain drill of end wheel design
which couples Land Pride spring mounted coulter to
achieve no-till drilling capabilities. The end wheel design
keeps the ground-working components in line with the
end wheels for accurate coulter depth and seed
placement over uneven terrain and allows the unit to
follow filed curves without side-loading the openers.
Figure 1
706/1006NT Drill
Intended Usage
38001
Document Family
Use this drill to primarily for no-till drilling. It can easily be
adapted for conventional drilling applications.
313-855M
Operator’s Manual (this document)
313-855P
706/1006NT Parts Manual
Models Covered
313-855Q
706/1006NT Pre-Delivery Manual
313-855B
Seed Rate Manual
This manual applies to Land Pride compact drill model:
706/1006NT
15-row 7.5-inch (19.1 cm)
Identifies an Economic (not a Safety) Risk:
NOTICE provides a crucial point of information related to the
current topic. Read and follow the instructions to avoid damage
to equipment and ensure desired field results.
Using This Manual
This manual familiarizes you with safety, assembly,
operation, adjustments, troubleshooting, and
maintenance. Read this manual and follow the
recommendations to help ensure safe and efficient
operation.
The information in this manual is current at printing.
Some parts may change to assure top performance.
Refer to 706/1006NT End-Wheel, No-Till Drill seed rate book
for seed rate charts, calibration instructions, and setting seed
rate instructions.
2015-08-04
Note: This form sets off useful information related to the
current topic, or forestalls possible
misunderstanding.
Right-hand and left-hand as used in
this manual are determined by facing
the direction the machine will travel
while in use unless otherwise stated.
An orientation rose in some line art
illustrations shows the directions of:
Up, Back, Left, Down, Front, Right.
706/1006NT  313-855M
U
B
R
F
D
L
11
Introduction
Table of Contents
Owner Assistance
If you need customer service or repair parts, contact a
Land Pride dealer. They have trained personnel, repair
parts and equipment specially designed for Land Pride
products.
Refer to Figure 2
Your machine’s parts were specially designed and
should only be replaced with Land Pride parts. Always
use the serial and model number when ordering parts
from your Land Pride dealer. The serial-number plate is
located on the top front cross-tube, left of the left gauge
wheel mount.
Record your drill model and serial number here and on
the bottom of the warranty page (inside back cover) for
quick reference:
Model Number:__________________________
Serial Number: __________________________
Figure 2
Serial Number Location
32802
Further Assistance
Your Land Pride dealer wants you to be satisfied with
your new drill. If for any reason you do not understand
any part of this manual or are otherwise dissatisfied with
the product please contact:
Land Pride Service Department
P.O. Box 5060
Salina, KS 67402-5060
Or go to www.landpride.com and follow the contact information at the bottom of your screen for our service FAQs.
12
706/1006NT  313-855M
2015-08-04
Table of Contents
Preparation and Setup
This section will help you prepare your tractor and drill
for use. Before going to the field, you must hitch a
tractor to the drill, hook up hydraulics and check that
hydraulics have been bled.
Prestart Checklist
❒
Read and understand “Important Safety
Information,” page 1.
❒
Check that all working parts are moving freely, bolts
are tight, and cotter pins are spread.
❒
Check that all grease fittings are in place and
lubricated. Refer to “Lubrication,” page 29.
❒
Check that all safety decals and reflectors are
correctly located and legible. Replace if damaged.
See “Safety Decals,” page 5.
❒
Inflate tires to pressure recommended and tighten
wheel bolts as specified. See “Appendix,” page 37.
Hitching Tractor to Drill
You may be severely injured or killed by being crushed
between the tractor and drill. Do not stand or place any part
of your body between drill and moving tractor. Stop tractor
engine and set park brake before installing the hitch pin.
Hitch Assembly
Refer to Figure 2
1. Insert upper hitch plate (1) into clevis hitch (2) with a
spacer tube (3) on each side of ball swivel.
1. Bolt in place with 1 x 5 1/2 inch bolt (4), flat washer
(5) and nylock nut (6).
Figure 3
Hitch Assembly
2015-08-04
706/1006NT  313-855M
13939
13
Preparation and Setup
Table of Contents
Hitch Height
Refer to Figure 3
For proper field operation, drill tongue should run level
in field position.
a. With drill in field position, adjust tongue jack to
level tongue.
b. Measure tractor drawbar height to determine
proper hitch height on drill.
c. Attach hitch to tongue with two 3/4 x 6 inch bolts
(1), lock washers (2) and nuts (3).
Note: Mounting holes in drill hitch are offset so hitch can
be turned over and attached in three different
positions, giving six different hitch heights.
Figure 4
Hitch Height
21703
Note: When hitching drill to a different tractor, check for
a difference in draw-bar heights. If heights are
different, readjust accordingly.
Hitching to Tractor
Refer to Figure 4
1. Back tractor to drill. Using the screw jack, adjust
drill tongue to get drawbar under upper hitch plate
(1).
2. Align rear hole in upper hitch plate with large hole
in drawbar. Place lower hitch plate (4) under
drawbar and attach to upper hitch plate with two 5/8
x 4 inch bolts (5), flat washers (6) and nylock nuts
(7).
3. Bolt top upper hitch plate through hole in drawbar
to lower hitch plate with 1 x 5 1/2 inch bolt (8), USS
flat washer (3) and nylock nut (2).
4. Securely attach safety chain to drill hitch with a 3/4
x 2 1/4 inch bolt (10), safety washer (11), lock
washer (12) and nut (13). Then attach chain to
tractor drawbar.
Figure 5
Tractor Hitch
13944
Refer to Figure 5
5. Store jack on top of tongue.
Figure 6
Jack Storage Position
14
706/1006NT  313-855M
13940
2015-08-04
Preparation and Setup
Table of Contents
Hydraulic Hose Hookup
Refer to Figure 6
Land Pride hydraulic hoses are color coded to help you
hook up hoses to your tractor outlets. Hoses that go to
the same remote valve are marked with the same color.
Color
Hydraulic Function
Blue
Transport Lift Cylinders
To distinguish hoses on the same hydraulic circuit, refer
to plastic hose holder. Hose under extended-cylinder
symbol feeds cylinder base ends. Hose under
retracted-cylinder symbol feeds cylinder rod ends.
Figure 7
Hydraulic Hose Label
17641
Rephasing Cylinders
The lift cylinders may, after a period of time, get out of
time or phase. The effects of this can be seen when
one side of the drill is running too low or too high
because its lift cylinder is either over extended or not
retracted compared to the other lift cylinder.
To rephase the cylinders, raise drill completely and hold
tractor hydraulic lever on for a few seconds to give
cylinders time to rephase.
Each time drill is raised out of ground momentarily
reverse hydraulic lever immediately after rephasing to
allow cylinders to retract about 1/2 inch. This will help in
maintaining a level drill.
Note: Understand that having cylinders become
gradually out of time is different than having air
trapped in the system from improper bleeding.
Each condition is corrected differently.
2015-08-04
706/1006NT  313-855M
15
Preparation and Setup
Table of Contents
Bleeding Hydraulics
Escaping fluid under pressure can have sufficient pressure to
penetrate the skin. Check all hydraulic lines and fittings
before applying pressure. Fluid escaping from a very small
hole can be almost invisible. Use paper or cardboard, not
body parts, and wear heavy gloves to check for suspected
leaks. If injured, seek medical assistance from a doctor that is
familiar with this type of injury. Foreign fluids in the tissue
must be surgically removed within a few hours or gangrene
will result.Check that tractor hydraulic reservoir is full.
The drill lifting system is equipped with rephasing type
hydraulic cylinders that require a special procedure for
bleeding air from the hydraulic circuits. Read and follow
this procedure carefully. Rephasing type cylinders will
not function properly with air in hydraulic circuit.
1. Check hydraulic fluid in tractor reservoir and fill reservoir to proper level. Drill-system capacity is about
1 gallon. Add fluid to system as needed. A low reservoir level may draw air back into the system,
causing jerky or uneven cylinder movements.
2. With drill attached to tractor, jack drill up and
support frame at ends near gauge wheels.
3. With drill raised and supported, unpin cylinders
from gauge wheel arms and frame. Turn cylinders
"rod end up". Wire or otherwise safely support rod
ends higher than base ends.
Note: In order to prevent trapped air pockets, rod end
must be higher than any other part of cylinder
during bleeding operation.
4. With tractor engine idling, engage tractor hydraulics
to extend cylinder rods. When cylinder rods are
completely extended, hold remote lever on for one
minute.
5. Retract cylinders. Extend cylinders again and hold
remote lever on for one more minute. Repeat this
step two more times to completely bleed system.
6. Repin cylinders to drill frame and gauge wheel arm
with transport cylinder locks in place. If any air still
is trapped in either cylinder, the cylinder will have a
spongy, erratic movement and drill will not raise
evenly. If necessary, repeat bleeding process.
7. Refill tractor hydraulic fluid reservoir to its proper
level.
Note: After the drill is raised, a slight settling will occur
due to the action of the rephasing cylinders.
16
706/1006NT  313-855M
2015-08-04
Preparation and Setup
Table of Contents
Leveling Drill
Refer to Figure 7
1. Loosen locknuts (2) and adjust cylinder eyebolts
(1). The eye bolts are factory pre-set at 4 3/4” of
thread above mounting plate.
8. Raise drill with hydraulics until openers and coulters
are 1 to 2 inches off the ground.
9. Measure height of coulter tube from ground on both
ends of drill.
10. Adjust eyebolt to level drill from end to end.
11. Tighten nuts on eyebolts when drill is level.
Do not exceed 5” of thread above mounting plate. This could
lead to hydraulic cylinder damage.
2015-08-04
706/1006NT  313-855M
Figure 8
Leveling Drill
20704
17
Table of Contents
Operating Instructions
This section covers general operating procedures.
Experience, machine familiarity and the following
information will lead to efficient operation and good
working habits. Always operate farm machinery with
safety in mind.
Escaping fluid under pressure can have sufficient pressure to
penetrate the skin. Check all hydraulic lines and fittings
before applying pressure. Fluid escaping from a very small
hole can be almost invisible. Use paper or cardboard, not
body parts, and wear heavy gloves to check for suspected
leaks. If injured, seek medical assistance from a doctor that is
familiar with this type of injury. Foreign fluids in the tissue
must be surgically removed within a few hours or gangrene
will result.
Prestart Checklist
Field Operation
1. Carefully read “Important Safety Information,” page
1.
2. Lubricate drill as indicated under “Lubrication,” page
29.
3. Check all tires for proper inflation. See “Appendix,”
page 37.
4. Check all bolts, pins and fasteners. Torque as shown
in “Appendix,” page 37.
5. Check drill for worn or damaged parts. Repair or
replace parts before going to the field.
6. Check hydraulic hoses, fittings and cylinders for
leaks. Repair or replace before going to the field.
7. Rotate both gauge wheels to see that the drive and
meters are working properly and free from foreign
material.
1. Hitch drill to a suitable tractor.
2. Set seed population as explained in the seed rate
book.
3. Load box with clean seed.
4. Raise drill. Rotate gauge wheel. Check that feed
cups, seed tubes and drives are working properly
and free from foreign material by looking for seed
flow under each opener.
5. Record acremeter readout. Subtract initial reading
from later readings to determine acres drilled.
6. Pull forward, lower drill and begin seeding.
7. Always lift drill out of the ground when turning at row
ends and for other short-radius turns. Seeding will
stop automatically as drill is raised.
Watch your step when walking on drill ladder and walkboard.
Falling from drill could cause severe injury or death.
18
You may be severely injured or killed by being crushed
between the tractor and drill. Do not stand or place any part of
your body between drill and moving tractor. Stop tractor
engine and set park brake before installing pins.
706/1006NT  313-855M
2015-08-04
Operating Instructions
Table of Contents
Opener Operation
Never back up with openers in the ground. To do so may cause
damage or opener plugging.
For information on opener adjustments, refer to page 23.
For more information on troubleshooting opener
problems, see “Troubleshooting”, page 27.
Transporting
Towing the drill at high speeds or with a vehicle that is not
heavy enough could lead to loss of vehicle control. Loss of
vehicle control could lead to serious road accidents, injury
and death. To reduce the hazard, do not exceed 20 mph. Check
that your tractor has enough ballast to handle the weight of
the drill. Refer to your tractor operator’s manual for ballast
requirements.
Failure of hydraulic cylinders during transport will cause drill
to drop suddenly, which could lead to serious road accidents,
injury or death. To prevent an accident, always install cylinder
locks before transporting drill.
Before transporting the drill, follow and check these
items:
Cylinder Locks
Cylinder locks 1 are located near both hydraulic cylinders.
With drill fully raised place lock over rod of cylinder and
secure in place with pin and clip.
1
Note: The cylinder locks can be engaged or disengaged
only after the drill is fully raised.
Unload Drill Box
The drill can be transported with a full box of grain, but the
added weight will increase stopping distance and
decrease maneuverability. Unload drill box before
transporting if at all possible.
Clearance
Remember that the drill is wider than the tractor. Allow safe
clearance.
Road Rules
Comply with all federal, state and local safety laws when
traveling on public roads.
1
Figure 9
Cylinder Locks
2015-08-04
706/1006NT  313-855M
21706
19
Operating Instructions
Table of Contents
Lock-out Hub
Refer to Figure 9
Make sure drive lock-out hub on both sides of drill are
disengaged before transporting. This will prevent
excessive wear of drive system during transport.
Figure 10
Lock-out Hub
14741
Figure 11
Jack Storage Position
20461
Parking
Perform the following steps when parking the drill. Refer
to “Storage”, page 29, to prepare for long-term storage.
1. Park drill on a level, solid area.
2. Lower drill until openers are resting on the ground.
3. Securely block tires to prevent rolling.
Refer to Figure 10
4. Remove tongue jack from storage stob. Pin jack on
side of tongue. If ground is soft, place a board or
plate under jack.
5. Extend jack until tongue weight is off tractor drawbar.
6. Unplug hydraulic hoses and wiring harness from
tractor. Do not allow hose ends or harness ends to
rest on the ground.
7. Remove hitch bolt and safety chain from tractor
drawbar.
20
706/1006NT  313-855M
2015-08-04
Table of Contents
Adjustments
Coulter Adjustments
Refer to Figure 11
A no-till coulter (1) is mounted directly ahead of each
opener on the drill. The coulters cut through heavy trash
and make a groove in the soil for the openers. The
coulters are mounted on the drill frame so coulter cutting
depth changes as the drill is raised and lowered.
To set drill seeding depth, you must:
1. Set coulter depth with hydraulic stop.
2. Set opener depth with T-handles on press wheels.
3. If soil conditions make it necessary, increase coulter
down pressure by adding weights.
If necessary, adjust individual coulters or openers to
seed in tire tracks, refer to page 22.
Coulter cutting depth is controlled by a depth control
valve.
The amount of coulter down force needed to cut a soil
groove varies with soil conditions. Adding weight or
shortening the coulter spring increases coulter down
pressure and cutting force.
Figure 12
Coulter
13985
Figure 13
Coulter Depth Stop
21708
Coulter Depth Control
The master-slave lift cylinders on your drill control the
depth of the coulters. A depth valve regulates the
retracted length of these cylinders.
Refer to Figure 12
1. Slightly raise drill with depth stop engagement arm
on the rock shaft not touching the valve.
2. Turn the depth control knob clockwise. Each rotation
lowers the coulters approximately 1/4 inch.
3. Raise and lower drill a few times to recheck depth.
Note: Changing depth of coulters will effect planting
depth of openers. Press wheels will need to be
adjusted accordingly.
2015-08-04
706/1006NT  313-855M
21
Adjustments
Table of Contents
Coulter Down Pressure
Pounds Per Coulter
Weights
If more weight is required for your soil conditions, add
weights to weight brackets located on box frame. No
more than 1100 pounds for the 706 (550 pounds per
side) and 1500 pounds for the 1006 (750 pounds per
side) should ever be added. Add an equal amount of
weight to each end of drill. See Figure 14.
Refer to Figure 13
7 inch
7.5
inch
8 inch
Empty Drill
274
282
290
Drill with 300
pounds added
304
314
323
Drill with 600
pounds added
334
345
356
Figure 14
Weight Chart
Spring Length
Coulter springs are preset at 9 7/8 to 10 inches, giving
coulters an initial operating force of 400 pounds. This
setting is adequate for many difficult no-till conditions.
Resetting coulter-spring length shorter than 9 3/4 inches may
contribute to premature failure of parts and warranty will be
voided. If additional force is needed, add weights to drill.
For lighter no-till conditions where rocks or other
obstructions are a problem, you can lengthen coulter
springs to protect coulters from impact.
Figure 15
Coulter Spring Length
Individual Coulter Adjustment
Individual coulters can be lowered if coulters follow in
tractor tire tracks and do not give satisfactory depth. To
do so:
20482
Spring
Length
Initial Vertical Coulter Force
10 1/2 inches
175 pounds
1. Loosen 5/8 inch jam nuts on 5/8 inch square head
set screws. Then loosen set screws.
2. Lower coulter to desired depth.
10 1/4 inches
300 pounds
10 inches
400 pounds
3. Tighten set screw on side of coulter clamp first.
This squares coulter bar in clamp.
9 3/4 inches
525 pounds
4. Tighten set screw on front of coulter clamp. Then
tighten both 5/8 inch jam nuts on each set screw.
Figure 16
Spring Length Chart
Note: Torque 5/8 inch set screws 85-100 ft-lbs to obtain
adequate holding force.
22
706/1006NT  313-855M
2015-08-04
Adjustments
Table of Contents
Opener Adjustments
Opener Down Pressure
Refer to Figure 14
Opener springs provide the down pressure necessary
for opener disks to open a seed trench. The springs
allow the openers to float down into depressions and
up over obstructions.
Each opener spring can be adjusted for down pressure.
This is useful when penetrating hard soil and for
planting in tractor tire tracks.
To adjust the pressure, remove “W” clip at bottom of
spring. Place “W” clip in a higher hole in spring rod for
more pressure or in a lower hole for less pressure.
Figure 17
Maximum Pressure on Opener
12103
Figure 18
Minimum Pressure on Opener
12102
Opener Seeding Depth
Refer to Figure 15
A press wheel attached to each opener body controls
seeding depth. To maintain consistent depth, the
relationship between the bottom of the opener disks
and press wheel is fixed upwardly by an adjustable stop
on each opener.
The press wheels also close the seed trench and
gently press soil over seed. To provide consistent soil
firming, press wheels are free to move down from
normal operating position. This maintains pressing
action even if opener disks encounter obstructions or
hard soil.
1
Set opener seeding depth by adjusting press-wheel
height. To adjust, first raise drill slightly, then lift and
slide T-handles 1 on top of openers as shown in
Figure 2.
• For shallower seeding, slide T-handles toward drill.
• For deeper seeding, slide T-handles away from drill.
Figure 19
Press Wheel Adjustment
2015-08-04
706/1006NT  313-855M
15659
23
Adjustments
Table of Contents
Disk Scraper Adjustment
Refer to Figure 16
To keep opener disks turning freely, dirt scrapers are
mounted between disks to clean as the disks rotate. As
field conditions vary, scrapers may need to be adjusted.
In damp conditions, scrapers may need to be lowered.
If openers are not turning freely, scrapers may need to
be raised.
1
To adjust scrapers, loosen 3/8 inch bolt 1 and move
scraper as needed.
Figure 20
Disk Scraper Adjustment
16153
Gauge Wheel Idler Adjustment
Refer to Figure 17
2
Located inside the left hand gauge wheel arm is two
idler sprockets which should be readjusted after the
first 100 acres of drill use. From then on, readjust at the
beginning of each season.
1
To adjust, move front idler sprocket on top of chain
down by loosening jam nut 1 and screwing in
adjustment stud 2 .
Retighten jam nut to maintain idler position.
Note: Do not over-tighten chains. To do so will cause
excessive wear.
Figure 21
Gauge Wheel Idler Adjustment
14744
Drive Clutch
Refer to Figure 18
The main drive clutch on your drill is a mechanicalrelease, jaw-style design. You may need to adjust the
clutch for proper engagement and disengagement.
When properly adjusted, the cam plates 1 will
disengage the clutch jaws completely when the drill is
raised. When lowered in field position, clutch jaws
should be engaged.
1
2
To adjust, loosen bolts on clutch tab 2 . Slide tab
forward or back to change point at which cam plates
meet. When satisfied with adjustment, retighten bolts
on clutch tab.
Figure 22
Drive Clutch
24
706/1006NT  313-855M
21709
2015-08-04
Adjustments
Table of Contents
Drive Train Operation
Refer to Figure 19
Check all chain idlers at beginning of each season for
proper adjustment. Check that each idler is taking up
excess chain slack. The access door 1 is located on
the top side of the gage wheel arm near the pivot end.
After first 100 hours of use and at beginning of each
season, readjust idler sprocket in left wheel arm. To
access idlers, remove access door.
5
Figure 23
Refer to Figure 20
To adjust idler sprocket, move top idler sprocket (1)
down into chain by loosening jam nut and screwing in
adjustment stud (2). Retighten jam nut to maintain idler
position.
Note: Do not overtighten chains. Overtightening chains
will cause excess wear on idlers and drive
components. Be sure chain is installed with the
chain connector link retainer towards the
centerline and the clip opening (split end) faces
the opposite way of the chain travel.
Figure 24
2015-08-04
706/1006NT  313-855M
25
Adjustments
Table of Contents
Spring Tine Harrow
Harrow Tine Angle
Refer to Figure 21
The drawing on the right shows a successful harrow
position for no-till and minimum-till conditions. Because
of different soil moisture, trash levels and trash types,
you may need to reposition the tube frame or tines.
Initially position the frame and tines as shown, then
readjust as necessary.
Figure 25
Tine Angle
16297
Figure 26
Frame and Tine Adjustment
16297
Harrow Frame and Tine Adjustment
Refer to Figure 22
To adjust harrow frame loosen the four hex nuts (1) on
the u-bolts and rotate frame tube (2) as necessary.
To adjust tines, loosen the four 1/2-inch hex nuts (3) on
the 1/2-inch u-bolts (4) on the support bar (5). Rotate
tine tubes (6) so tines (7) are against stop bushings (8)
and are angled back as necessary. Retighten hex nuts
on u-bolts.
Harrow Chain
Refer to Figure 23
In clean, tilled, extremely loose soils, harrow chain may
need to be shortened to lift harrow off the ground.
To adjust chain, support the harrow to remove weight
from the harrow arms 1 . Remove the lower bolt 2 and
select a different chain link.
Note: Keep the harrow arms at the same length.
1
2
Figure 27
Harrow Chain Adjustment
26
706/1006NT  313-855M
21712
2015-08-04
Table of Contents
Troubleshooting
Problem
Cause
Solution
Uneven seed spacing or uneven
stand
Excessive field speed.
Reduce field speed.
Feed cups plugging.
Seed tubes plugging.
Opener disks not turning freely.
Uneven seed depth
Opener disks not turning freely
Actual seeding rate different than
desired
Excessive seed cracking
Acremeter does not measure accurately.
Press wheels not compacting soil as
desired
2015-08-04
Clean out feed cups.
Clean out seed tubes.
See “Opener disks not turning freely”
in this Troubleshooting section.
Opener not penetrating low spots.
Adjust opener, page 25.
Use faster drive type speed and close
feed cup flutes to a more narrow position.
Excessive field speed.
Reduce field speed.
Planting conditions too wet.
Wait until drier weather.
Drill not level.
Readjust, page 18.
Incorrect hitch height.
Readjust hitch height, page 15.
Trash or mud build up on disk scraper. Adjust scraper, page 26.
Scraper adjusted too tight, restricting Adjust scraper, page 26.
movement.
Failed disk bearings.
Replace disk bearings.
Bent or twisted opener frame.
Replace opener frame.
Planting conditions too wet.
Wait until drier weather.
Too much opener down pressure.
Readjust opener down pressure,
page 25.
Incorrect press wheel adjustment.
Readjust press wheel, page 25.
Improper tire size or air pressure.
Check tire size and air pressure, page
41.
Build up of seed treatment in feed
Clean seed treatment from feed cups.
cup.
Incorrect rate adjustment.
Check gearbox setting and seed-rate
handle setting, refer to the seed rate
book.
Excessive field speed.
Reduce field speed.
Feed cup flutes not open enough.
Open feed cups to a wider position.
Feed cup door handle not open
Open feed cup door handle to a lower
enough.
position.
Incorrect tire size or air pressure.
Correct tire size or air pressure, page
41.
Excessive overlap or gaps between
Avoid overlap or gaps.
passes.
Soil conditions.
Loose soil and slippage will cause
variations in acres registered.
Acremeter not for your width of drill.
Refer to parts manual.
Actual field size different.
Verify field size.
Too wet or cloddy.
Wait until drier weather or rework
ground.
Incorrect hitch height.
Readjust hitch height, page 15.
706/1006NT  313-855M
27
Troubleshooting
Table of Contents
Problem
Cause
Solution
Readjust press wheel depth, page 25.
Grain box not emptying evenly
Press wheel depth does not match
coulter depth.
Not enough down pressure on disk
openers.
Some models do not have same number of feed cups between each divider
of bulkhead.
Planting conditions too wet.
Too much down pressure on openers.
Press wheel or openers plugging
Raising and lowered drill is rough or
uneven
Feed cup sprockets locked up or
twisted feed cup drive shaft
Coulters not going deep enough
Coulters and drill going too deep
Backed up with drill in the ground.
Failed disk bearings.
Scraper worn or damaged.
Wheel arm pivot casting needs lubricating.
Leaking hydraulic fittings.
Rephasing cylinders not bled properly.
Foreign matter lodged in one or more
feed cup sprockets.
Dried liquid insecticide inside feed
cups.
Not enough weight.
Too much weight.
Incorrect depth control setting.
Incorrect press wheel adjustment.
Coulters and openers plugging in notill conditions
Small seeds box not emptying evenly Adjustable divider not set evenly.
Chain
28
Debris, retainer clip
706/1006NT  313-855M
Increase down pressure on openers,
page 25.
Wait until drier weather.
Reduce down pressure on openers,
page 25.
Clean out and check for damage.
Replace disk bearings.
Replace scraper.
Lubricate wheel arm pivot castings.
Check fittings for leaks, see page 16
for safety message.
See page 16 for information.
Clean out feed cup sprockets. Use
clean seed.
Remove build up by disassembling
each feed cup and scraping foreign
substance from turn surfaces.
See page 24 for correct weight.
See page 24 for correct weight.
Reset depth control, page 23.
Set press wheels to a shallower
depth.
Drill at a slight angle to rows.
Move adjustable divider to create
more volume in areas that run out
first.
Be sure retainer clip is facing opposite
way of chain travel.
2015-08-04
Table of Contents
Maintenance and Lubrication
Maintenance
Storage
Proper servicing and maintenance is the key to long
implement life. With careful and systematic inspection,
you can avoid costly maintenance, downtime and repair.
Store drill where children do not play. If possible, store
the drill inside for longer life.
Always turn off and remove the tractor key before making
any adjustments or performing any maintenance.
You may be severely injured or killed by being crushed under
the falling implement. Always have transport locks in place
and frame sufficiently blocked up when working on implement.
Escaping fluid under pressure can have sufficient pressure to
penetrate the skin. Check all hydraulic lines and fittings before
applying pressure. Fluid escaping from a very small hole can
be almost invisible. Use paper or cardboard, not body parts,
and wear heavy gloves to check for suspected leaks. If injured,
seek medical assistance from a doctor that is familiar with this
type of injury. Foreign fluids in the tissue must be surgically
removed within a few hours or gangrene will result.
1. Unload seed box.
2. Thoroughly clean seed and seed-treatment residue
from boxes and feed cups.
3. Remove any dirt and debris that can hold moisture
and cause corrosion.
4. Lubricate and adjust all roller chains.
5. Take special care to oil feed cup drive sprocket in its
square bore.
6. Lubricate areas noted under “Lubrication”, page 29.
7. Inspect drill for worn or damaged parts. Make repairs
and service during the off season.
8. Use spray paint to cover scratches, chips and worn
areas on the drill to protect the metal.
9. Disconnect seed hoses from openers. Permanent
elongation and premature cracking of hoses may
occur if stored connected.
10. Cover with a tarp if stored outside.
1. After using the drill for several hours, check all bolts
to be sure they are tight.
2. Lubricate areas listed under “Lubrication”, page 29.
3. Adjust idlers to remove excess slack from chains.
Clean and use chain lube on all roller chains as
needed.
4. Inflate tires as specified on “Tire Inflation Chart”,
page 37.
5. Clean out build up of seed treatment in feed cups.
6. Replace any worn, damaged or illegible safety
decals. Order new decals from your Land Pride
dealer. See “Safety Decals”, page 37.
2015-08-04
706/1006NT  313-855M
29
Maintenance and Lubrication
Table of Contents
Lubrication and Scheduled Maintenance
Multi-purpose
spray lubricant
Multi-purpose
oil lubricant
Multi-purpose
grease lubricant
Inspection
50
Intervals
(operating hours)
at which service
is required
Clutches
8min
Two zerks on each.
Smear grease on clutch engagement teeth.
Type of Lubrication: Grease
Quantity = Until grease emerges
14755
Coulter Hub Bearings
Seasonal
One zerk per coulter; 15 total
Type of Lubrication: Grease
Quantity = Until resistance is felt
13879
Drive Chains
As Required
Type of Lubrication: Chain Lube
Quantity = Coat thoroughly.
12227
30
706/1006NT  313-855M
2015-08-04
Maintenance and Lubrication
Table of Contents
Feed Cup Drive Shaft Sprocket
50min
1 sliding sprocket
Type of Lubrication: Oil
Quantity: Coat thoroughly
Move the Seed Rate adjustment handle back and forth to
get oil into the square bore. Perform this with seed box
empty, or handle may be difficult to set to 100.
Felt Barrier Seals
12126
16381
30min
1 seal at each shaft end, 2 total
Type of Lubrication: Oil
Quantity: Soak seal
If Small Seeds is also installed, access these seals from
below or through the end wall gaps.
Fertilizer Tray Bearings
15min
Both ends of shaft
Type of Lubrication: Grease
Quantity = Until grease emerges
12506
2015-08-04
706/1006NT  313-855M
31
Maintenance and Lubrication
Table of Contents
Gauge Wheel Arms
15min
Type of Lubrication: Grease
Quantity = Until grease emerges
21709
Gearbox
On Repair
The gearbox is lubricated and sealed at the factory.
Under normal conditions, it does not require
maintenance or lubrication.
If the gearbox has been opened for repair, repack all
gears and around shaft bearings using at least 7 oz. of
gear lube, part number 788067.
Keep moisture and dirt out of gearbox. Inspect (replace if
needed) the rubber seals on gearbox drive and shifter
shafts.
Spread a small skim coat of anaerobic sealant
(Loctite® 525 or equivalent) to gear case mating surfaces
before bolting them back together.
14757
Use sparingly. Excess sealant may squeeze off the intended
surface and lock bearings or gears.
Grease Banks
8min
Type of Lubrication: Grease
Quantity = Until grease emerges
14753
32
706/1006NT  313-855M
2015-08-04
Maintenance and Lubrication
Table of Contents
Ground Drive Wheel Bearings
Seasonal
2 races per wheel; 4 total
Type of Lubrication: Grease
Quantity = repack
28299
Small Seeds Feed Cup Drive Sprocket
50min
Type of Lubrication: Oil
Quantity = Coat sprocket bore thoroughly
12226
Small Seeds Shaft Bearings (Option)
15min
1 zerk total
Type of Lubrication: Grease
Quantity: Until grease emerges
18082
2015-08-04
706/1006NT  313-855M
33
Table of Contents
Options
Seed Box Agitator
The seed box agitator is designed to stir the seed
directly above the metering cups. It is intended to cut
down on the “bridging” of light fluffy seeds, and help to
separate individual soybeans that become sticky from
inoculant.
Note: NOTE: The seed box agitator will not guarantee
consistent seeding of hard to meter seeds such
as Brome Grass or “bin run” seed that contains
crop residue.
For lubrication points, refer to “Lubrication”, page 29.
To order the seed box agitator, contact your Great
Plains dealer.
Agitator
Packages
12682
706
row spacing
(inches)
With
small seeds,
native grass
or fertilizer
Without
small seeds,
native grass
or fertilizer
7
7.5
8

Part Number
118-893A

118-895A


118-895A
118-894A

118-896A

118-896A
Harrow Attachment
The coil-tine harrow finishes no-till surfaces by leveling
and distributing residue for enhanced seed
germination.
For information on how to adjust the harrow, refer to
“Harrow Adjustment”, page 26.
To order the harrow attachment, contact your Great
Plains dealer.
Harrow Packages
34
Part Number
706 Harrow Attachment
116-278A
1006 Harrow Attachment
116-279A
14024
706/1006NT  313-855M
2015-08-04
Options
Table of Contents
Fertilizer Attachment
The fertilizer attachment allows you to plant seed and
apply fertilizer in the same field pass. The fertilizer box
mounts on the rear of the main drill box. A fertilizer drive
meters dry, granular fertilizer.
For fertilizer meter rate calibrating and charts, refer to
“Fertilizer Meter Rate” in the seed rate book. For
lubrication points, refer to “Lubrication”, page 29.
To order the fertilizer attachment, contact your Great
Plains dealer.
10986
Small Seeds Attachment
The small seeds attachment is designed to meter
various small seeds. It is driven independently of the
main seed box. The small seeds box is 0.24 bushel per
foot (27.7 liters/meter) with a total capacity of 2.62
bushes (92.3 liters).
The small seeds attachment is available with two seed
release point options: In row delivery and side delivery.
With the In row delivery, small seeds are metered and
dropped between the disc blades or just in front of the
press wheel.
With the side delivery, small seeds are metered and
dropped just to the side of the opener furrow.
For seed rates and adjustments, refer to “Small Seeds
Attachment” in the seed rate book. For lubrication points,
refer to “Lubrication”, page 29.
13734
To order the small seeds attachment, contact your Great
Plains dealer.
Seed-Lok® Firming Wheels
The spring-loaded Seed-Lok® firming wheel presses
seed directly into the bottom of the seed bed. The SeedLok® option provides more even emergence since seeds
are planted and firmed at the same depth. Seed-Lok®
can be used on all units except native grass, unless
native grass tube is removed during Seed-Lok® use.
To order the Seed-Lok® firming wheels, contact your
Great Plains dealer.
Seed-Lok® Packages
Seed-Lok® Assembly
2015-08-04
Part Number
122-193K
706/1006NT  313-855M
35
Options
Table of Contents
Series II Native Grass Attachment
The native grass attachment is designed to seed fluffy,
hard-to-plant grasses.
For seed rates and adjustments, refer to “Native Grass
Attachment” in the seed rate book.
To order the native grass attachment, contact your
Great Plains dealer.
21783
Folding Tongue
The folding tongue is designed to allow narrower widths
for trailer towing of drill and for space saving during
storage.
To order the folding tongue, contact your Great Plains
dealer.
Folding Tongue Packages
Part Number
1006 Folding Tongue
151-111A
706 Folding Tongue
151-114A
21825
36
706/1006NT  313-855M
2015-08-04
Table of Contents
Appendix
Torque Values Chart
Bolt Head Identification
Bolt Head Identification
Bolt
Size
Bolt
Size
Grade 2
in-tpia
N-mb ft-lbd
Grade 5
Grade 8
5.8
10.9
Class 5.8
Class 8.8
Class 10.9
N-m
ft-lb
N-m
ft-lb
mm x pitchc
N-m
ft-lb
N-m
ft-lb
N-m
ft-lb
1
7.4
5.6
11
8
12
M 5 X 0.8
4
3
6
5
9
7
1
e4-28
8.5
6
13
10
18
14
M6X1
7
5
11
8
15
11
5e
16-18
15
11
24
17
33
25
M 8 X 1.25
17
12
26
19
36
27
5e
16-24
17
13
26
19
37
27
M8X1
18
13
28
21
39
29
e4-20
3e
8-16
27
20
42
31
59
44
M10 X 1.5
33
24
52
39
72
53
3e
8-24
31
22
47
35
67
49
M10 X 0.75
39
29
61
45
85
62
7
e16-14
43
32
67
49
95
70
M12 X 1.75
58
42
91
67
125
93
7
e16-20
49
36
75
55
105
78
M12 X 1.5
60
44
95
70
130
97
1
66
49
105
76
145
105
M12 X 1
90
66
105
77
145
105
150
e2-13
1
e2-20
75
55
115
85
165
120
M14 X 2
92
68
145
105
200
9
e16-12
95
70
150
110
210
155
M14 X 1.5
99
73
155
115
215
160
9e
16-18
5
e8-11
5e -18
8
3e -10
4
3
e4-16
7
e8-9
7
e8-14
105
79
165
120
235
170
M16 X 2
145
105
225
165
315
230
225
165
250
185
130
97
205
150
285
210
M16 X 1.5
155
115
240
180
335
245
150
110
230
170
325
240
M18 X 2.5
195
145
310
230
405
300
235
170
360
265
510
375
M18 X 1.5
220
165
350
260
485
355
260
190
405
295
570
420
M20 X 2.5
280
205
440
325
610
450
585
430
820
605
M20 X 1.5
310
230
650
480
900
665
640
475
905
670
M24 X 3
480
355
760
560
1050
780
1-8
340
250
875
645
1230
910
M24 X 2
525
390
830
610
1150
845
1-12
370
275
955
705
1350
995
M30 X 3.5
960
705
1510
1120
2100
1550
11e8-7
480
355
1080
795
1750
1290
M30 X 2
1060
785
1680
1240
2320
1710
11e8-12
540
395
1210
890
1960
1440
M36 X 3.5
1730
1270
2650
1950
3660
2700
M36 X 2
1880
1380
2960
2190
4100
3220
11e4-7
680
500
1520
1120
2460
1820
11e4-12
750
555
1680
1240
2730
2010
13e8-6
890
655
1990
1470
3230
2380
a. in-tpi = nominal thread diameter in inches-threads per inch
b. N· m = newton-meters
13e8-12
11e2-6
1
1 e2-12
1010
745
2270
1670
3680
2710
1180
870
2640
1950
4290
3160
1330
980
2970
2190
4820
3560
c. mm x pitch = nominal thread diameter in mm x thread pitch
d. ft-lb = foot pounds
Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.
Tire Inflation Chart
Tire Size
9.0 x 24" 8-Ply Rib Implement
Inflation PSI
25199m
25199
NOTE: All tires are warranted by the original manufacturer of the tire. Tire warranty information can be found in
the brochures included with your Operator’s and Parts
Manuals or online at the manufacturer’s websites. For
service assistance or information, contact your nearest
Authorized Farm Tire Retailer.
40
Manufacturer
Titan
2015-08-04
8.8
Website
www.titan-intl.com
Goodyear
www.goodyearag.com
706/1006NT  313-855M
37
Appendix
Table of Contents
Specifications and Capacities
706
Row Spacing, Inches
Rows Per Drill
Approx. Weight, Pounds
Working Width
1006
7
7.5
8
7
7.5
8
11
10
10
16
15
14
3,900
3,800
3,800
4,500
4,300
3,200
7 feet
10 feet
9 feet 10 inches
12 feet 7 inches
Transport Height
6 feet 7 inches
6 feet 7 inches
Transport Length
13 feet 10 inches
13 feet 10 inches
17.1 bushels
23.75 bushels
9.00 x 24
9.00 x 24
55 horsepower; one
remote valve
75 horsepower; one
remote valve
Transport Width
Approx. Seedbox Capacity
End Wheel Tires
Tractor Requirements
Hydraulic Schematics
38
706/1006NT  313-855M
2015-08-04
Appendix
Table of Contents
Seed Box Sprocket Configuration
21754
Seed Box Agitator Sprocket Configuration
21753
2015-08-04
706/1006NT  313-855M
39
Appendix
Table of Contents
Small Grass Seeds Sprocket Configuration
21755
Native Grass Sprocket Configuration
21756
40
706/1006NT  313-855M
2015-08-04
Appendix
Table of Contents
Fertilizer Sprocket Configuration
21757
21757
Fertilizer with Small Grass Seeds Box Sprocket Configuration
21758
2015-08-04
706/1006NT  313-855M
41
Appendix
Table of Contents
Warranty
Land Pride warrants to the original purchaser that this seeding equipment will be free from defects in material and workmanship for a period
of one year from the date of original purchase when used as intended
and under normal service and conditions for personal use; 90 days for
commercial or rental purposes. This Warranty is limited to the replacement of any defective part by Land Pride and the installation by the dealer of any such replacement part. Land Pride reserves the right to inspect
any equipment or part which are claimed to have been defective in material or workmanship.
This Warranty does not apply to any part or product which in Land
Prides’ judgment shall have been misused or damaged by accident or
lack of normal maintenance or care, or which has been repaired or altered in a way which adversely affects its performance or reliability, or
which has been used for a purpose for which the product is not designed. This Warranty shall not apply if the product is towed at a speed
in excess of 20 miles per hour.
Claims under this Warranty must be made to the dealer which originally
sold the product and all warranty adjustments must by made through
such dealer. Land Pride reserves the right to make changes in materials
or design of the product at any time without notice.
This Warranty shall not be interpreted to render Land Pride liable for
damages of any kind, direct, consequential, or contingent, to property.
Furthermore, Land Pride shall not be liable for damages resulting from
any cause beyond its reasonable control. This Warranty does not extend to loss of crops, losses caused by harvest delays or any expense
or loss for labor, supplies, rental machinery or for any other reason.
No other warranty of any kind whatsoever, express or implied, is
made with respect to this sale; and all implied warranties of merchantability and fitness for a particular purpose which exceed
the obligations set forth in this written warranty are hereby disclaimed and excluded from this sale.
This Warranty is not valid unless registered with Land Pride within 10
days from the date of original purchase.
42
706/1006NT  313-855M
2015-08-04
Table of Contents
Table of Contents
Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement