Installation Instructions ERVXX15_ERV

Installation Instructions ERVXX15_ERV
Installation Instructions
Renaissance ® Downdraft Vent
Models ERV3015, ERV36-ER, ERV3615, ERV48,
ERV48-ER, PRV30, PRV36 and PRV46
Includes installation instructions for cabinet blower (Dacor model CABP3) which is
an option for models ERV3015 and ERV3615.
Use these downdraft vents only with approved Dacor ® appliances. See the
installation instructions for the particular appliance model being installed to
determine suitability.
Part No. 107736 Rev. B
Table of Contents
Important Safety Instructions........................................... 1
Important Information About Safety Instructions............... 1
Safety Symbols and Labels.............................................. 1
General Safety Precautions.............................................. 2
Product Specifications...................................................... 2
Electrical Specifications.................................................... 2
Product Dimensions - ERV3015 and ERV3615................ 3
Product Dimensions - ERV48 and PRV Series................ 4
Product Dimensions - ERV36-ER and ERV48-ER........... 5
Installation Specifications................................................. 6
Planning the Installation.................................................... 6
Planning the Duct Work.................................................... 8
Installation Instructions................................................... 12
Installation Preparation................................................... 12
Installing the Downdraft Vent in the Cutout.................... 13
Verifying Proper Operation.............................................. 16
Installation Checklist....................................................... 16
Wiring Diagram - All Models........................................... 17
CABP3 Cabinet Blower Ratings...................................... 17
Before You Begin...
Important:
•
Installer: In the interest of safety and to minimize problems, read these installation instructions completely and carefully before you begin the installation process. Leave these installation instructions with the customer.
•
Customer: Keep these installation instructions for future reference and the local electrical inspector’s use.
Customer Service Information
If You Need Help...
Model Identification
If you have questions or problems with installation, contact
your Dacor ® dealer or the Dacor Customer Service Team.
For repairs to Dacor appliances under warranty call the Dacor
Distinctive Service line. Whenever you call, have the model
and serial number of the appliance ready. The model and serial number are printed on the product data label on the front of
the unit. The product data label also specifies the power supply requirements.
Dacor Customer Service
Phone: ((800) 793-0093 ex. 2813 (U.S.A. and Canada)
Monday - Friday 6:00 a.m. to 5:00 p.m. Pacific Time
ERV3015
= 30-inch wide downdraft vent with ERV
style top cap. For use with approved
Dacor cooktops and ranges.
ERV3615
= 36-inch wide downdraft vent with ERV
style top cap. For use with approved
Dacor cooktops and ranges.
ERV36-ER = 36-inch wide downdraft vent with ERV
style top cap. For use with approved
Dacor ranges.
ERV48
Web site: www.dacor.com
Dacor Distinctive Service (for repairs under warranty only)
Phone: 793-0093 ex. 2822 (U.S.A. and Canada)
Monday - Friday 6:00 a.m. to 5:00 p.m. Pacific Time
= wide downdraft vent with ERV style
top cap. For use with approved Dacor
cooktops and ranges.
ERV48-ER = 48-inch wide downdraft vent with ERV
style top cap. For use with approved
Dacor ranges.
PRV30
= wide downdraft vent with PRV style
top cap. For use with approved Dacor
cooktops and ranges.
PRV36
= 36-inch wide downdraft vent, PRV
style top cap. For use with approved
Dacor cooktops and ranges.
PRV46
= 46-inch wide downdraft vent, PRV
style top cap. For use with approved
Dacor cooktops.
All specifications subject to change without notice.
Dacor assumes no liability for changes to specifications.
© 2013 Dacor, all rights reserved.
Important Safety Instructions
Important Information About
Safety Instructions
•
•
The Important Safety Instructions and warnings in
these instructions are not meant to cover all possible
problems and conditions that can occur. Use common
sense and caution when installing, maintaining or operating this or any other appliance.
Always contact the Dacor Customer Service Team
about problems and conditions that you don’t understand. See Customer Service Information.
Safety Symbols and Labels
DANGER
Immediate hazards that WILL result in severe personal
injury or death.
warning
Hazards or unsafe practices that COULD result in severe
personal injury or death.
caution
Hazards or unsafe practices that COULD result in minor
personal injury or property damage.
DANGER
IMPORTANT: Do not store or use combustible,
flammable or explosive vapors and liquids (such as
gasoline) inside or in the vicinity of this or any other
appliance. Also keep items that could explode, such
as aerosol cans, away from the range or cooktop. Do
not store flammable or explosive materials in adjacent
cabinets or areas.
warning
WARNING – TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
a) Installation work and electrical wiring must be
done by qualified person(s) in accordance with
all applicable codes and standards, including
fire-rated construction.
b) Sufficient air is needed for proper combustion
and exhausting of gases through the
flue(chimney) of fuel burning equipment to
prevent back drafting. Follow the heating
equipment manufacturer’s guideline and safety
standards such as those published by the
National Fire Protection Association (NFPA), and
the American Society for Heating, Refrigeration
and Air Conditioning Engineers (ASHRAE), and
the local code authorities.
c) When cutting or drilling into wall or ceiling, do
not damage electrical wiring and other hidden
utilities.
warning
This appliance is equipped with a three prong grounding
plug for your protection against possible electric shock
hazards. It must be plugged into a dedicated, grounded
electrical outlet. Where a standard two prong electrical
outlet is encountered, it is the personal responsibility
and obligation of the customer to have it replaced with a
dedicated, properly grounded three prong electrical outlet.
Do not under any circumstances:
♦♦
Cut or remove the third (ground) prong from the
power cord.
♦♦
Use an adapter plug.
♦♦
Use an extension cord.
♦♦
Use a power cord that is frayed or damaged.
♦♦
Use of a ground fault interrupter (GFI) is not
recommended.
Grounding
type
electrical
outlet
Three prong
grounding plug
d) Ducted fans must always be vented to the
outdoors.
READ AND SAVE THESE INSTRUCTIONS
1
Important Safety Instructions
General Safety Precautions
To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following:
Warning
warning
• Do not install or operate a damaged appliance. If you
receive a damaged appliance, contact your dealer or
builder.
• The installer must show the customer the location of
the electrical outlet so that the customer knows where
and how to disconnect power.
• Observe all governing codes and ordinances during
planning and installation. Contact your local building
department for further information.
• Install or locate this appliance only in accordance
with these installation instructions, the Dacor range/
cooktop installation instructions and the blower installation instructions. Improper installation, adjustment,
alteration, service or maintenance can cause serious
personal injury or property damage.
• The electric outlet for the downdraft vent should be
installed only by a licensed electrician
• For general ventilating use only. Do not use to
exhaust hazardous or explosive materials and vapors.
• Use this downdraft vent only for its intended purpose
as outlined in the use and care manual. This appliance is not intended for commercial use.
• The customer should not install, repair or replace
any part of this unit unless specifically recommended
in the literature accompanying it. A qualified service
technician should perform all other service. Contact
the Dacor Customer Service Team for examination,
repair or adjustment.
• Keep all packaging materials away from children.
Plastic bags can cause suffocation.
• For proper operation, this unit must be installed with a
cabinet, in-line or remote blower. Use only one of the
models specified. Only one blower shall be installed.
• Before installing or servicing the downdraft vent, disconnect the power plug from the electrical outlet.
• Read the use and care manual completely before
operating this appliance.
• Do not tamper with the controls.
• Never allow the filters or vent openings to become
blocked or clogged. Do not allow foreign objects, such
as cigarettes or napkins, to be sucked into the vent
holes.
• Clean the filters and all grease-laden surfaces often
to prevent grease fires and maintain performance.
Clean this appliance only as specified in the use and
care manual.
• Do not leave children or pets alone or unattended in
the area around the range or cooktop when it is in
use. Never allow children to sit or stand on an appliance. Do not let children play with a range, cooktop
or the downdraft vent. Do not store items of interest to
children above or around the appliance.
Product Specifications
Electrical Specifications
The downdraft vent is supplied with a 28” (71.1 cm) power
cord with a three prong plug. Plug it directly into a three
prong electrical outlet meeting the requirements below. Do
not use an extension cord.
•
The customer must supply 3 conductor wiring/conduit
with minimum current carrying capacity of 8 Amps. to
supply power to the blower from the downdraft vent.
See Installation Specifications for further details.
•
It is the owner’s responsibility to ensure that the electrical outlet is installed by a licensed electrician. The electrical installation must comply with the latest revision of
the National Electric Code ANSI/NFPA 70* (latest revision) and local codes and ordinances.
The correct voltage, frequency and amperage must be supplied as specified below. The circuit must be protected by a
properly sized circuit breaker or time-delay fuse.
*A copy of this standard may be obtained from:
Electrical Supply Requirements
A three prong electrical outlet connected to a 120 Vac,
60 Hz, 15 Amp. grounded, dedicated, single phase circuit
is required.
•
2
The above specifications are for reference only. If they
do not agree with those listed on the product data label,
use the ratings on the label.
•
National Fire Protection Association
1 Batterymarch Park
Quincy, Massachusetts 02269-9101
Locate the electrical outlet in an accessible location,
so that the power plug can be disconnected for service
without removing the appliances from the cabinet.
Product Specifications
Product Dimensions - ERV3015 and ERV3615
Tolerances: ±1/16” (±1.6 mm) unless otherwise stated
2 3/16”
(5.6 cm)
2 1/8”
5/16” (8 mm)
thick stiffener (5.4 cm)
across back
Top cap with
vent down
3/16”
(5 mm)
3”
(7.6 cm)
Model
Number
A - Top Cap
Width
B - Chassis
Width
ERV3015
30” (76.2 cm)
27 3/8” (69.5 cm)
ERV3615
36” (91.4 cm)
33 3/8” (84.8 cm)
9/16”
(1.4 cm)
2 1/8" (5.4 cm)
ERV top cap - side view
1 15/16”
(4.9 cm)
2 9/16” *
(6.5 cm)
A
Vent shown
in raised
position
3 3/4”
(9.5 cm)
1 1/8”
(2.9 cm)
7/16"
(1.1 cm)
15"
(38.1 cm)
B
20”
(50.8 cm)
2 1/8" (5.4 cm)
PRV top cap - side view
3/8"
(1.0 cm)
30"
30 1/4”
(76.8 cm) (76.2 cm)
to
37 1/4” **
(94.6 cm)
Product
data label
See pages 9 and
10 for exhaust
locations and
dimensions.
6”
(15.2 cm)
Motor
cover
Front of unit
28" 3 prong
grounded
power cord
Adjustable
anchor legs
* Total chassis depth with optional CABP3 blower installed is 10 3/8” (26.3 cm).
** Maximum height of downdraft vent must not exceed maximum specified counter
height for cooking appliance. See installation instructions for cooking appliance.
3
Product Specifications
Product Dimensions - ERV48 and PRV Series
Tolerances: ±1/16” (±1.6 mm) unless otherwise stated
2 3/16"
(5.6 cm)
5/16” (8 mm)
thick stiffener
across back
2 1/8"
(5.4 cm)
Top cap with
vent down
3/16"
(5 mm)
2 1/2"
(6.4 cm)
9/16"
(1.4 cm)
Model
Number
A - Top Cap
Width
B - Chassis
Width
ERV48
48” (121.9 cm)
43 3/8” (110.2 cm)
PRV30
30” (76.2 cm)
27 3/8” (69.5 cm)
PRV36
36” (91.4 cm)
33 3/8” (84.8 cm)
PRV46
46” (116.8 cm)
43 3/8” (110.2 cm)
1 15/16"
(4.9 cm)
2 9/16"
(6.5 cm)
A
Vent shown
in raised
position
2 1/8" (5.4 cm)
ERV top cap - side view
10"
(25.4 cm)
2 1/8" (5.4 cm)
PRV top cap - side view
B
18 5/8”
(47.3 cm)
3 3/4"
(9.5 cm)
1"
(2.5 cm)
30"
30 1/4" (76.2 cm)
(76.8 cm)
to *
37 1/4"
(94.6 cm)
6"
(15.2 cm)
Motor
cover
Front of unit
Adjustable
anchor legs
4
Product
data label
28" 3-prong
grounded
power cord
3/8"
(1.0 cm)
7/16"
(1.1 cm)
See page 9 for exhaust
locations and dimensions.
* Maximum height of
downdraft vent must
not exceed maximum
specified counter height
for cooking appliance. See
installation instructions for
cooking appliance.
Product Specifications
Product Dimensions - ERV36-ER and ERV48-ER
5/16” (8 mm)
thick stiffener
across back
1/4"
(6 mm)
2 13/16"
(7.1 cm)
2 1/2"
(6.4 cm)
Top cap with
vent down
Model
Number
Top Cap
Width (A)
Chassis
Width (B)
ERV36-ER
36” (91.4 cm)
33 3/8” (84.8 cm)
ERV48-ER
48” (121.9 cm)
43 3/8” (110.2 cm)
Tolerances: ±1/16”, (±1.6 mm) unless otherwise stated
1 15/16"
(4.9 cm)
2 9/16"
(6.5 cm)
A
Vent shown
in raised
position
10"
(25.4 cm)
B
18 5/8”
(47.3 cm)
3 3/4"
(9.5 cm)
1"
(2.5 cm)
30"
30 1/4" (76.2 cm)
(76.8 cm)
to
37 1/4" *
(94.6 cm)
Product
data label
See page 9 for
exhaust locations and
dimensions
28" 3 prong
grounded
power cord
* Maximum height of
downdraft vent must not
exceed maximum specified counter height for
cooking appliance. See
installation instructions for
cooking appliance.
6"
(15.2 cm)
Motor
cover
Front of unit
Adjustable
anchor legs
5
Installation Specifications
Planning the Installation
General System Layout
Backsplash
The vent system consists of the downdraft vent itself and a
single Dacor approved cabinet blower (models ERV3015 and
ERV3615), remote blower or in-line blower (see facing page
for examples).
Countertop
overhang
warning
• Failure to install an approved blower or proper duct
work will result in a back draft and/or the insufficient
venting of smoke and fumes.
• To reduce the risk of personal injury caused by reaching over a hot appliance, cabinet storage space
located directly above the range/cooktop should be
avoided.
Notches required for some downdraft vent
installations, see cooktop
installation instructions
• Follow the instructions and diagrams for minimum safe
clearances and installation location in these instructions, the appliance installation instructions and the
blower installation instructions. Failure to do so may
result in a fire or safety hazard.
•
Plan the installation so that all minimum dimensions
are met or exceeded. All contact surfaces between the
downdraft vent and any cabinets or walls must be solid
and at right angles.
•
The downdraft vent is equipped with adjustable anchor
legs to accommodate various cabinet heights.
•
Install the downdraft vent and range/cooktop so that
they can be removed if service is required.
•
When installing the downdraft vent with a cooktop,
access from the front of the cabinet to the chassis and
the electrical/gas supplies of both appliances must
be provided for inspection and service. Any drawers
or shelves must be easy to remove for access to the
cooktop, downdraft vent and utilities.
•
There are 7/8” access holes in the bottom and side of
the downdraft vent for connecting the blower wiring and
strain relief. Wire the blower to turn on when the downdraft vent is turned on. When installing a remote or inline blower, run the blower wiring/conduit parallel to the
duct work, connecting it to the downdraft vent on one
end and the blower on the other.
•
Allow room for the exhaust duct coming out of the unit.
See Planning the Duct Work for further details.
•
The maximum allowable duct run must be taken
into consideration when determining the layout. See
Planning the Duct Work for further details.
•
Refer to the range/cooktop installation instructions for
the minimum cutout dimensions specific to the particular downdraft vent model being installed.
6
Vertical
non-combustible
surface rear wall
See the cooktop installation
instructions for exact countertop
and cabinet dimensions
Flush with back side
of cabinet front
Cooktop Cabinet/Countertop Cutout - Top View
Backsplash
Vertical
non-combustible
surface rear wall
Countertop
overhang
Notches required for some downdraft vent
installations, see range
installation instructions
Notches for self-rimming
style installations, see range
installation instructions
See the range installation
instructions for exact countertop
and cabinet dimensions
Range Cabinet/Countertop Cutout - Top View
Installation Specifications
Backsplash
Front of unit
Cooktop
Cabinet blower option on ERV3015,
and ERV3615 only
Connection to
cabinet blower
Connection to
remote/in-line
blower
Downdraft vent
Blower wiring
access hole
Cabinet blower,
option on
ERV3015 and
ERV3615
only
Wall
Floor
Blower wiring
access hole
Wall cap
3 1/4 x 10
90° elbow
Electrical Layout
12” min.
(30.5 cm)
REMP series
remote blower
Example of Layout with Cabinet
Blower Configuration, Exhaust Through Wall
3 ¼ x 10 to
round transition
and 45°
adjustable elbow
Wall board
Duct work between
downdraft and
remote blower
Backsplash
Cabinet back
Outside wall
Downdraft vent
Cooktop
Downdraft vent
Range
Downdraft vent
configured for
bottom exhaust
Downdraft vent
configured for
rear exhaust
3 ¼ x 10 to
round transition
Wiring/conduit
from downdraft
to remote blower
Floor
Example of Layout with Cooktop
and Rear Exhaust
Duct work
Wiring/conduit
from downdraft to
in-line blower
Wall cap on
outside wall
Floor
Duct work
ILHSF series
in-line blower
Example of Layout with Range
and Bottom Exhaust
7
Installation Specifications
Planning the Duct Work
Installations with ILHSF and REMP series blowers:
warning
• To reduce the risk of fire and to properly exhaust air,
be sure to duct air outside the house or building. Do
not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces or garages.
• TO REDUCE THE RISK OF FIRE, USE ONLY METAL
DUCT WORK.
With ILHSF and REMP blowers, the downdraft vent can
be configured to exhaust through the back, the bottom or
either side by removing the appropriate exhaust knock-out
shown on the facing page.
•
When connecting the duct work to the back of the unit,
the customer must supply a 3 ¼ x 10 rectangular transition to make the connection.
•
For side and bottom exhaust connections, use the supplied transition to connect the duct work to the unit. It
transitions between the 1 5/8 x 16 exhaust outlet on the
unit and a 3 ¼ x 10 rectangular duct connection. On
bottom exhaust installations cut a hole in the floor to
allow the transition and/or duct work to pass through
the floor (see page 13).
• DO NOT install more than one blower to increase the
length of the duct run. Even small differences between
blower air flow rates can greatly reduce the air draw
by the downdraft vent.
Local building codes may require the use of makeup air
systems with ventilation systems that move air greater than
the specified movement rate (CFM). The specified rate varies based on locale. Consult a qualified HVAC specialist
when designing the system for the requirements in your
area and to assure optimal performance.
You must install one of the Dacor blower models listed
below for the downdraft vent to operate properly. See the
blower installation instructions for directions. For model
CABP3, see the instructions later in this manual.
1"
(2.5 cm)
APPROVED DACOR BLOWERS FOR USE WITH
MODEL ERV-PRV SERIES DOWNDRAFT VENTS
Dacor Blower
Model Number
CABP31
Rating
600
CFM2
600
CFM4
ILHSF10
1100 CFM4
REMP3
600
CFM4
REMP16
1000
ILHSF8
CFM4
3 ¼ x 10 to duct work
Compatible with
Vent Models
ERV30153
ERV36153
ALL
ALL
2 x 16, connects to
side or bottom exhaust
on downdraft
5"
(12.7 cm)
1 5/8 x 16 Duct Transition
•
On side exhaust installations, allow five inches of space
on the side for the 2 x 16 to 3 ¼ x 10 transition plus
additional space for the duct attached to it (X).
ALL
X
ALL
1
IMPORTANT: Due to a lack of clearance, do not use a
CABP3 blower if a range or wall oven is to be installed in
front of the downdraft vent.
2
Nominal rating at zero inches static pressure, see the
CABP3 blower ratings on page 17 for actual rating.
3
Revision B and later units only.
4
Nominal rating at zero inches static pressure. See blower
installation instructions for actual ratings.
For installations with CABP3 blowers:
•
Installation with a CABP3 blower requires Dacor adapter kit # AERVCAB.
•
The blower assembly is mounted to the front of the
downdraft vent with the exhaust pointing in the desired
direction. See page 10.
•
The CABP3 blower output connects directly to 3 ¼ x 10
rectangular duct.
8
1 5/8 x 16 duct
transistion
5”
Installation Specifications
6 1/4"


Front of unit
Motor
cover





26" (66.0 cm)
1 1/8"
(2.9 cm)
CL (15.9 cm)
CL
3”


CL
 Rear Exhaust Knock Out (3 ¼ x 10)
 Vertical center line of rear exhaust knock out lines up with vertical
center line of chassis
 Bottom Exhaust Knock Out (1 5/8 x 16)
 On 46” and 48” wide models, the vertical center line of bottom knock-
out lines up with vertical center line of chassis
 On 30” and 36” wide models, the vertical center line of bottom knockout is offset 3”
 Side Exhaust Knock Outs (1 5/8 x 16)
Exhaust Knock-out Locations for Use with
REMP and ILHSF Series Blowers
Duct installation requirements for all blowers:
•
Use sheet metal screws as required to support the duct
weight.
•
All duct work materials (including screws and duct tape)
must be purchased separately by the customer.
•
•
When planning new duct work, always look for the
shortest, most direct route to the outside. See page
7 for examples.
To prevent back-drafts, a damper at the duct outlet may
also be required.
•
Make sure duct work does not interfere with floor joists
or wall studs.
•
You can increase the duct size over the duct run if
desired. To prevent a back draft, never decrease the
duct size over the run.
•
With concrete slab construction, “box-in” the duct work
and blower wiring to prevent collapsing or other damage when the wet concrete is poured.
•
Do not rely on duct tape alone to seal duct joints.
Fasten all connections with sheet metal screws and
tape all joints with certified silver tape or duct tape.
•
Cross-drafts or air currents from adjacent open windows or doors, heating/air conditioning outlets, ceiling
fans and recessed ceiling lights reduce vent efficiency.
•
System exhaust location (see page 8) must take
into account accumulated snowfall, where applicable.
9
Installation Specifications
Exhaust Locations and Dimensions
for CABP3 Cabinet Blower Installations
(ERV3015, ERV3615 only)
ERV
Cooktop
Model
A
B
C
ERV3015
12 1/8”
(30.7 cm)
5 5/8”
(14.4 cm)
1 3/4”
(4.4 cm)
ERV3615
9 3/4”
(24.8 cm)
8”
(20.3 cm)
4 1/4”
(10.8 cm)
CABP3
C
L
Countertop
ADAPTER
8 7/8" (22.5 cm)
from back of ERV
cutout to center
line of CABP3
exhaust in any
orientation
A
26 1/4”
(66.7 cm)
3 1/4 x 10
duct
connection
DUCT
Bottom exhaust
configuration shown
Exhaust Locations and Side Dimensions
for CABP3 Cabinet blower
Downdraft vent
center line
Countertop
B
Downdraft vent
center line
Duct connection
center line
Front Exhaust Dimensions
CABP3 Blower - Left Exhaust
Countertop
Downdraft vent
center line
Duct connection
center line
C
15 3/8”
(39.1 cm)
3 1/4 x 10
duct
connection
Duct connection
center line
29 1/4”
(74.3 cm)
3 1/4 x 10
duct connection
Front Exhaust Dimensions
CABP3 Blower - Right Exhaust
10
Front Exhaust Dimensions
CABP3 Blower - Bottom Exhaust
Installation Specifications
Calculating the Maximum Duct Run Length
Duct Work Design Tips
•
For optimal performance, consult a qualified HVAC
specialist when designing the duct system.
•
•
Do not use duct work that is smaller in cross-sectional
area than the required duct sizes in the tables below.
•
Keep the duct run as short as possible for best performance and never exceed the maximums stated in the
table below right.
Wherever possible, reduce the number of transitions
and turns to as few sharp angles as possible. Two
staggered 45° angles are better than one 90°. Keep
turns as far away from the hood exhaust as possible,
with as much space between each bend as possible.
•
•
The maximum duct length for the downdraft vent system depends on the blower model used and the number of elbows and transitions. The Equivalent Number
of Feet for each elbow and transition (see table below)
must be subtracted from the maximum straight length
to compensate for wind resistance. To determine the
maximum allowable length of the duct work, subtract all
of the equivalent lengths of the elbows and transitions
listed below from the Blower Maximum Duct Straight
Length (see table right).
For best performance, use round duct instead of rectangular when possible, especially when elbows are
required.
•
If multiple elbows are used, try to keep a minimum of
24” of straight duct between them. Avoid “S” or “back to
back” configurations of adjacent elbows.
•
Do not use flexible metal duct.
For example, for a downdraft vent system using 3 ¼ x 10
rectangular duct, two (2) 3 ¼ x 10 90° elbows, a 3 ¼ x 10
rectangular to 10” round transition, and a REMP16 remote
blower:
• From the Blower Maximum Duct Straight Length
table below, the maximum length without transitions
and elbows is 60 feet.
• The equivalent length of each 90° elbow is 15 feet.
• The equivalent length of 45° elbow is 2 feet.
• The equivalent length of the transition is 4 feet.
• The total equivalent length of the above components is:
15 feet + 15 feet + 4 feet + 2 feet = 36 feet.
• The maximum amount of straight duct that can be used
with a REMP16 and the above components is: 60 feet 34 feet = 24 feet.
Blower
Used
Blower Maximum Duct Straight Length
8 Inch Duct
10 Inch Duct
3 ¼ x 10
Duct
CABP3
40 feet
(12.2 m)
30 feet
(9.2 m)
30 feet
(9.2 m)
ILHSF8
50 feet
(15.2 m)
40 feet
(12.2 m)
40 feet
(12.2 m)
ILHSF10
60 feet
(18.3 m)
70 feet
(21.3 m)
60 feet
(18.3 m)
REMP3
50 feet
(15.2 m)
40 feet
(12.2 m)
40 feet
(12.2 m)
REMP16
60 feet
(18.3 m)
70 feet
(21.3 m)
60 feet
(18.3 m)
Equivalent Number of Feet (Nominal) Duct Elbows and Transitions
45° elbow
8 inch
3 feet
3 ¼ x 10
45° elbow
7 feet
45° elbow
10 inch
2 feet
3 ¼ x 10
90° elbow
15 feet
90° elbow
8 inch
7 feet
3 ¼ x 10
90° flat elbow
20 feet
90° elbow
10 inch
5 feet
3 ¼ x 10
to 8” round
transition
4 feet
90° 3 ¼ x 10
to 8” round
transition
25 feet
3 ¼ x 10
to 10” round
transition
4 feet
Roof cap
*
Wall cap**
*
* The equivalent lengths of roof and wall caps vary with
model and configuration. For equivalent length, contact the
manufacturer or a qualified HVAC specialist.
** Not applicable for REMP series blowers.
11
Installation Instructions
Installation Preparation
Verify Package Contents
1. Unpack the unit and verify that all required parts have
been provided. If any item is missing or damaged,
please contact your dealer immediately. Do not install a
damaged or incomplete appliance. The customer must
report cosmetic issues within 30 days of installation.
Parts List
• Product literature
• Anchoring legs (left - PN 36861, right - PN 36862)
• 2 wood screws, #14 x 2 1/2 (PN 83047)
• 3 wire nuts
• 1 5/8 x 16 to 3 ¼ x 10 duct transition (PN 13768)
• 2 sheet metal screws, #10 x 1/2 (PN 83022)
• 2 keps nuts, 1/4-20 (PN 83049)
• 2 flat washers, 1/4-20 (PN 83203)
• Insulation foam (tape)
Installation Preparation for Downdraft Vent
with ILHSF or REMP Series Blower:
NOTE: For units using the CABP3 cabinet blower, skip to
Installation Preparation for Downdraft Vent with CABP3
Cabinet Blower, on facing page.
1. Remove the appropriate side, back or bottom exhaust
knockout, depending on the desired exhaust configuration, from the downdraft vent chassis by cutting the
metal cross overs and removing the insert (see below).
Back of unit
Side
knock-out
Side
knock-out
Rear knock-out with
metal cross overs
shown
Installation with CABP3 blower requires Dacor adapter kit
# AERVCAB. Kit includes adapter, wiring diagram label
(PN 106770), 3 wing nuts (PN 83035), 3 flat washers (PN
83008) and 6 lock washers (PN83340).
Bottom knock-out
warning
• If the electrical service (electrical outlet) does not meet
the Electrical Specifications on page 2, do not
proceed with the installation. Call a licensed electrician
and have an electrical outlet installed that meets the
specifications.
2. Cut and remove the foil material inside the knock-out
hole. If you fail to remove the foil, the vent will not work.
•
• Install the vent only in a vertical orientation. Do not
mount the vent on a slant or angle.
• Do not enlarge or modify the exhaust knock-outs or
cut an exhaust hole in a location on the chassis other
than those shown. Doing so may cause an increase in
noise and decrease performance.
If the unit will vent through the bottom or side,
install the suppled 1 5/8 x 16 to 3 ¼ x 10 transition
to the exhaust location. Before installing, peel the
protective backing off the foam tape and apply it to
the transition flanges. Attach the transition with the
provided sheet metal screws (see below).
Transition side
installation
NOTE: The downdraft vent installs in the back of the cutout, separate from the range or cooktop. Install the downdraft vent before installing the range or cooktop.
Attach sealing
foam
2. Start by loosely attaching the anchoring legs to the
studs on the left and right sides of the downdraft vent
using the provided Keps nuts and washers.
Anchor leg
Front of unit
Transition bottom
installation
Put nuts/
washers on
studs
•
If the unit will exhaust air from the back, attach a
3 ¼ x 10 duct to the vent hole created by removing
the knock-out on the back of the unit.
3. Skip to Installing the Downdraft Vent in the Cutout
on page 13.
12
Installation Instructions
Adapter Installation for CABP3 Blower:
(optional, ERV3015 and ERV3615 only)
1. Remove the front cover so that the AERVCAB cabinet
blower adapter can be installed. To do so, remove and
retain the three (3) wing nuts and three (3) flat washers
on the front of the unit. Discard the three (3) lock washers (they will be replaced). Tilt the cover out and pull
up. to remove it.
Installing the Downdraft Vent in
the Cutout
1. Cut a hole in the cabinet to allow the duct work to pass
through to the floor or wall for the planned duct system
layout. Use the dimensions on pages 9 and 10 to
determine the hole center line locations. If using the 2” x
16” to 3 1/4” x 10” transition (REMP and ILHSF blower
installations), the hole may need to be enlarged slightly.
Rear corner of cutout
(back of downdraft vent)
plumbed down
Front of unit
Cover
2. Peel the backing off of some of the foam tape included
with the adapter. Attach it to the right and left flanges.
3. Hold the adapter in front of the opening on the front
of the unit with the adapter’s studs on top and all the
flanges closest to the downdraft vent chassis.
4. Slide the bottom flange on the adapter into the bottom
retainer bracket on the downdraft vent at an angle.
Attach the adapter using the three (3) wing nuts and
flat washers removed in
step 1 and three (3) of
the lock washers from the
adapter kit.
2. Gently slide the vent into the rear of the countertop cutout with the electrical access panel toward the front.
3. Adjust the anchoring leg height so that the top of the
downdraft vent rests on the counter, then tighten the
hex nuts. Secure the anchoring legs to the cabinet floor
with the provided wood screws.
Top of vent resting
on countertop
Front of unit
Front of unit
Studs
Attach foam
to right/left
flanges
Adapter
Bottom retainer bracket
Insert bottom
flange into
bottom retainer
bracket
Anchor leg
Floor
Electrical access
panel
Exhaust: size and location
varies with installation type
13
Installation Instructions
Cabinet Blower Installation:
ILHSF or REMP Series Blower Installation
(optional, ERV3015 and ERV3615 only)
If using a ILHSF or REMP series blower, install it according
to the blower installation instructions.
1. Locate the wiring diagram label included with the
adapter kit. Peel the protective backing off and place it
over the existing label on the CABP3 blower as shown.
New label
Duct Work Installation
warning
Tape all duct joints securely to prevent combustion
by-products, smoke or odors from entering the home.
Doing so will also improve system efficiency.
Existing
label
2. Locate the foam tape supplied with the downdraft vent.
Place the blower on the floor in the orientation it will be
mounted on the front of the downdraft vent. Peel the
backing off the included foam tape and attach it to the
right and left flanges of the blower base plate.
3. With the exhaust in the desired orientation, slide the
bottom flange of the CABP3 blower base plate behind
the tab on the bottom of the adapter mounted to the
front of the downdraft vent.
4. Cover the opening on the adapter by pushing the
blower against it. Make sure that the foam tape creates a good seal on the right and left side of the opening. Center the blower base plate horizontally over the
opening on the front of the adapter.
5. Install the adapter top retainer bracket over the blower
base plate flange. Secure it in place with the three (3)
wing nuts, lock washers and flat washers included with
the adapter.
Attach foam
to right/left
flanges
Adapter
Insert bottom flange into
tab at bottom of adapter
14
Electrical Installation
warning
• ELECTRIC SHOCK HAZARD - Do not connect the
downdraft vent power plug to the electrical outlet until
installation is complete.
• Failure to complete electrical connections properly
may result in an electric shock hazard or a damaged
or non-functional system. Follow the wiring diagrams
carefully to ensure a proper installation. Do not
change the factory wired terminal connections inside
the electrical access panel for the downdraft vent or
the blower.
• To avoid an electric shock hazard and to prevent damage route all wiring away from hot surfaces.
1. For ILHSF and REMP blower installations, run the wiring/conduit line used to supply power from the downdraft vent to the blower parallel to the duct work.
2. Remove the cover from the downdraft vent electrical
access panel.
Top retainer
bracket
CABP3
Install the duct work according to the Installation
Specifications section. Use sheet metal screws and duct
tape to connect and seal all of the pieces. Support the duct
weight as necessary to ensure sealed joints.
3. Connect the wiring/conduit to the blower as shown in
the wiring diagrams below and the facing page according to local codes and ordinances. Make sure all terminal connections, including the factory wired connections, are tight. Replace the electrical access panel.
Range/Cooktop Installation
Install the range or cooktop according to its installation
instructions.
Installation Instructions
Wires to power plug.
Pre-wired at factory.
Do not modify.
Match wire colors to
terminals as shown.
Front of unit
BLACK
WHITE
Electrical connection
from downdraft vent,
match Wire Colors
Electrical access
panel
Ground
Power
Input
Blower
Output
CABP3 cabinet
blower
GREEN
Attach ground wire
as shown
Downdraft vent
blower wiring
access hole
Electrical Installation - CABP3 Cabinet Blower
Blower power wiring/conduit.
Connect other end of wires
to blower terminal block.
Wire Colors : Black = Line (L), White = Neutral (N),
Green = Ground (Gnd)
Downdraft Vent Electrical Access Panel
REMP16
remote blower
Connect wires/conduit
according to remote
blower installation
instructions
Downdraft vent
Example of Electrical Installation
with ILHSF or REMP Series Blower
(Side View)
Range
See Downdraft Vent
Electrical Access
Panel, above
Wiring/conduit from
downdraft vent to remote
(or in-line) blower
Floor
15
Installation Instructions
Verifying Proper Operation
warning
• Read the downdraft vent use and care manual completely before operation.
• Install all of the front filters prior to operating the
downdraft vent. Refer to the use and care manual for
filter installation instructions.
caution
To prevent damage to the downdraft vent power cord,
route it away from the surfaces of the range or cooktop
before connecting it.
1. Make sure the power switch on the top of the downdraft
vent is in the up position.
2. Plug the downdraft vent power plug into the electrical
outlet.
3. Press the power switch once to raise the vent to its
operating position.
4. Once in the up position the vent should begin to draw
air. Turn the variable speed control switch in both directions to verify that the system is operating correctly.
5. Press the top cap up/down switch once to lower the
vent.
6. Make sure that the top cap on the downdraft vent
intake does not catch on the back edge of the cooktop
or range when the intake is lowered. If interference
occurs, adjust the position of the cooktop or range.
Failure to eliminate any interference may result in permanent damage to the vent.
If the downdraft vent is not operational after installation:
•
Make sure that power is being supplied to the unit.
•
Make sure that power is being supplied to the blower
from the downdraft vent.
•
If the vent will not raise properly or makes a scraping
sound check for obstructions interfering with the raising
of the unit.
If the downdraft vent still does not function after performing the above checks, do not attempt to repair it yourself.
Contact Dacor Distinctive Service at 793-0093 ex. 2822. Be
sure to have all model and serial numbers from the product
data labels for the downdraft vent and the blower available
when you call.
Dacor is not responsible for the cost of correcting problems
caused by a faulty installation.
16
Installation Checklist
□□ Are the anchor legs extended down to make contact
with the floor and tightened into place? Are the anchor
legs fastened to the floor? Is the unit level?
□□ Is the duct work completely installed? Are all joints
attached with sheet metal screws and wrapped with
duct tape?
□□ Are both ends of the blower power cable connected (to
the downdraft vent and to the blower itself)?
□□ Are the vent filters installed according to the use and
care manual instructions?
□□ Is the power cord routed away from the hot surfaces of
the range or cooktop.
□□ Is the unit connected to an electrical outlet that meets
the electrical specifications in these instructions?
□□ Has proper operation been verified?
□□ Has the warranty been activated on-line or the warranty
card been filled out completely and mailed?
Technical Data
Wiring Diagram - All Models
UP
LIMIT SWITCH
DOWN
LIMIT SWITCH
SNORKEL SWITCH
COM
COM
COM NO NC
NC NO
RED
RED
BLUE
BLK
YEL
NO NC
CHASSIS
GROUND
STUD
WHT
WHT
YEL
WHT
BLUE
REMOTE POT
RELAY
N
SPEED CONTROL
BLK
ORNG
L
ORNG
COM
NO
L2
N2
BLOWER
OUTPUT
RED
L1
N1 GND GND
POWER
INPUT
GROUND
BLK
CABP3 Cabinet Blower Ratings
CABP3 Blower Performance
Nominal
600 CFM
Actual
585.6 CFM
* At zero inches static pressure. Performance varies based
on duct system configuration.
Electrical Rating: 4 Amps. @ 120 Vac, 60 Hz.
For ILHSF or REMP series blower ratings, see the blower
installation instructions.
Static pressure - inches of water
CABP3 Cabinet blower Airflow*
5.0
4.0
3.0
2.0
1.0
0
100 200 300 400 500 600
Airflow CFM (Cubic feet/minute)
17
Dacor ● 14425 Clark Avenue, City of Industry, CA 91745 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www.dacor.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement