advertisement
Receptor Digital Terrestre
TDT-130
MANUAL DE USUARIO
Lea este manual antes de la instalacion y uso del aparato
Español
INSTRUCCIONES DE SEGURIDAD
PARA REDUCIR EL RIESGO DE FUEGO O DESCARGA ELÉCTRICA, NO EXPONGA ESTE
APARATO A LA LLUVIA O HUMEDAD.
Por favor lea cuidadosamente estas instrucciones antes de usar la unidad.
Protección del cable de alimentación.
Para evitar cualquier mal funcionamiento de la unidad, y para protegerse contra una descarga eléctrica, fuego o daño personal, por favor tenga en cuenta lo siguiente:
- Sostenga firmemente el enchufe cuando conecte o desconecte el cable de alimentación.
- Mantenga el cable de alimentación alejado de fuentes de calor.
- No coloque ningún objeto pesado sobre el cable de alimentación.
- No intente reparar ni reconstruir el cable de alimentación en ningún caso.
- No cambie ni realice conexiones con el aparato encendido.
Colocación.
Evite colocar el aparato en lugares de:
Incidencia directa del sol o radiadores, o cerca de zonas con temperaturas elevadas o con mucha humedad (por encima del 90%), mucho polvo en las partes internas del receptor puede dañarlo seriamente.
Periodos de no utilización.
Cuando la unidad no se esté usando, apáguela. Si va a estar un largo periodo de tiempo sin usar el aparato, desconéctelo de la toma de corriente.
No tocar con los dedos u otros objetos el interior de la unidad.
Tocar las partes internas de esta unidad es peligroso y puede causar importantes daños al aparato. No intente desmontar la unidad.
No ponga objetos externos en su interior.
Mantener lejos del agua y de campos magnéticos.
Mantenga la unidad lejos de jarrones de flores, vasos, fregaderos, etc. Si entra líquido dentro de la unidad, podría sufrir grandes daños.
No coloque objetos que produzcan campos magnéticos cerca de la unidad.
Apilamiento.
Coloque la unidad en posición horizontal, no ponga objetos pesados sobre ella.
Condensación.
La humedad del ambiente puede condensarse dentro de la unidad en los siguientes casos:
- Inmediatamente después de encender una estufa en una habitación llena de humedad.
- Cuando la unidad es trasladada de golpe de una zona fría a una caliente.
Si la humedad se condensa dentro del aparato, ésta podría no funcionar correctamente. En este caso, encienda la unidad y espere alrededor de una hora hasta que la humedad se haya evaporado.
Si hay ruido de interferencia en el TV mientras recibe un canal.
Dependiendo de las condiciones de recepción del televisor, las interferencias pueden aparecer en su monitor mientras esté viendo algún canal. Esto no se debe a un mal funcionamiento del aparato o del televisor.
Reciclaje.
Este símbolo sobre el producto o las intrucciones de uso significa que su aparato eléctrico puede ser reciclado por separado al final de su vida útil. Hay diferentes sistemas de reciclaje por separado en la UE. Para más información, por favor consulte a las autoridades locales o a su proveedor donde tirar su producto correctamente.
CONTENIDO
INFORMACION DE SEGURIDAD
INTRODUCCION
Sobre el receptor
Panel frontal 1
Panel trasero 1
Mando a distancia 2
CONEXION DEL SISTEMA
General
Conectando la TV
Conectando el aparato HiFi
EMPEZANDO
Instalacion facil
Instalacion
Busqueda automatica
Busqueda de canales
Alimentacion de antena
OPERACIONES
3
3
3
4
4
4
4
4
Cambiar de canal
Acceder a la EPG
Acceder a la lista de favoritos
CANAL
5
5
5
6
7
7
6-7
7
7
Menu lista de canales
Lista de canales de TV
Lista de canales de Radio
Borra todos los favoritos
Borrar todo
Renombrar grupo
CONFIGURACION DEL SISTEMA
Menu de configuracion del sistema
Idioma de los menus
Sistema de TV
Configuracion de hora local
Configuracion de temporizadores
Configuracion del OSD
Control parental
Apagado automatico
HERRAMIENTAS
Menu principal de herramientas
Informacion del receptor
juegos
Restablecer configuracion de fabrica
Actualizacion de Software
Media+
Menu principal de Media+
Reproductor Multimedia
Gestor de grabaciones
Informacion del disco extraible
Configuracion del DVR
Extraccion segura del dispositivo USB
Formateo de disco
Grabacion/TimeShift
Timeshift (Grabacion en pausa)
Grabacion
PROBLEMAS COMUNES
13
13
15
11
11
11
11
11
12
12
9
9
9
9
8
8
8
8
10
10
10
10
10
ESPECIFICACIONES
16
Sobre el receptor
Panel frontal
Sensor mando a distancia
Botón de encendido
Puerto USB
Panel trasero
Entrada RF para una antena externa
Euroconector TV para conexión a su TV
Salida de audio digital coaxial
Cable alimentación
RF Loop through para un dispositivo externo
1 Español
INTRODUCCION
Mando a distancia
5 Cursor: Teclas de navegacion usadas para
moverse por los diferentes menus
STANDBY MUTE
1 14
2
3
4
5
6
7
1
4
7
INFO
MENU
RECORD
2
5
8
0
OK
EPG
AUDIO
6
SUBTITLE
9
RECALL TV/RADIO
EXIT
STOP
15
16
17
18
19
20
21
6 Tecla OK
(Para confirmar una seleccion dentro de un menu)
7 RECORD
(Para grabar un programa de TV)
8 VOL+,-
(VOL+/-:Subir y bajar el volumen)
9 TTX (Abre el teletexto)
10 SLEEP (Abre la lista del temporizador de apagado)
11 TIMESHIFT
(Activa la funcion timeshift o pausa diferida)
12 FILE
(Abre la lista de grabaciones)
13 GOTO (Va a un punto del fiichero a reproducir)
14 MUTE (Apagar /encender el sonido)
15
EPG
(Abre la Guia Electronica de Programacion)
8
9
10
11
9
12
13
13
VOL
TTX
TIMESHIFT SLEEP
FILE GOTO
FAV
PLAY
PAUSE
CH
REV
FWD
22
23
24
25
26
27
28
16
AUDIO
(Selecionar el modo y la pista de de audio)
17 SUBTITLE (Activar/Desactivar Subtitulos)
18
TV/RADIO
(Cambia entre TV y Radio)
19
RECALL
(Cambia al canal anterior)
20 EXIT (Salir del menu)
21
22
STOP
CH+,-
(CH+/-: Canal Arriba y Abajo)
23 FAV
(Abre la lista de favoritos)
24 REV
(Pulse REV para retroceso rapido)
1
2
3
4
STANDBY
(cambia entre modo encendido y reposo)
25
26
Teclado numerico
(Seleccione el canal deseado intorduciendo directamente su numero)
27
INFO
(para obtener lal informacion del canal en curso)
Menu
(Abre y cierra la pantalla de menu)
28
2
Español
PLAY
FWD
(Pulse FWD para avance rapido)
PAUSE(Activar /detener la funcion timeshift)
Teclas Roja/Verde/Amarilla/Azul
(Para funciones interactivas y de submenus)
CONEXIÓN DEL SISTEMA
General
Hay muchos tipos de equipos de televisión y de otro tipo que se pueden conectar al dispositivo.
En este manual podra ver algunas de las formas más comunes de conectar su equipo.
Conectando la TV
Cable Euroconector
Antena
Cable R F
TV
Conectando el aparato HIFI
Hi-Fi
Cable coaxial
3 Español
EMPEZANDO
Instalación Fácil
Si utiliza el receptor por primera vez, el menú "Instalación Fácil" aparecerá.
Presione "IZQUIERDA" o "DERECHA" sobre el botón cursor para configurar la zona horaria y el idioma del OSD.
Seleccione "Búsqueda" y presione el botón "OK" para empezar la búsqueda de canales.
Easy Install
Region
OSD Language
Search
Spain
English
Select OK Enter EXIT Exit
Instalación
1. Presione el botón "Menu" para entrar en el menú principal.
2. Presione "IZQUIERDA" o "DERECHA" para seleccionar
"Instalación", presione el botón "OK" para entrar en el menú de
instalación.
3. Presione el botón "EXIT" para salir.
Installation
Auto Scan
Channel Scan
Power Control
Select OK Enter EXIT Exit
Búsqueda Automática
Auto Scan
TV Channel List
2 BBCi
3 CBBC Channel
4 BBC 2W
Radio Channel List
1 BBC Radio Wales 1. Presione "ARRIBA" o "ABAJO" para seleccionar la "Busqueda
Automática", presione "OK" para entrar en el menú de Búsqueda
Automática.
2. Presione "IZQUIERDA" o "DERECHA" para seleccionar el
modo Búsqueda, marque "Buscar", entonces presione el botón
"OK" para empezar la búsqueda automática.
5 BBC THREE
6 BBC ONE Wales
2 BBC Radio Cymru
UHF: 470.0-862.0 MHz Ch No: GI:
Frequency: 490.00 Mhz Modulation: FFT:
24%
EXIT Exit
Búsqueda de Canales
1. Presione "ARRIBA" o "ABAJO" para seleccionar "Búsqueda
de Canales" y presione el botón "OK" para entrar en el menú
Búsqueda de Canales.
2. Presione "IZQUIERDA" o "DERECHA" para seleccionar el
modo de Búsqueda, Banda de búsqueda y nº de canal, entonces
presione el botón "OK" para empezar la búsqueda de canales.
Modo de Búsqueda de Canales:
Por canal
Por frecuencia
Channel Scan
Scan Mode
Scan band
Ch No.
Frequency
Band Width
Network Search
By Channel
UHF
22(482.000MHz)
482.000
8 MHz
Off
Search
Signal Intensity
Signal Quality
Select OK Enter EXIT
94%
97%
Exit
Alimentación de antena
Presione el botón "ARRIBA" o "ABAJO" para seleccionar
"Alimentación de Antena", presione "OK" para entrar en este menú.
Alimentación de antena: On/Off
RF Loop-through: On/Off
Power Control
Tuner Power Off
RF Loop-through Off
Change EXIT Exit
4 1
Español
OPERACIONES
Cambiar de canal
Hay tres maneras de seleccionar canales: moverse a través de la lista de canales, selección por número y desde la lista de canales en pantalla.
1. Moverse a través de la lista de canales:
Para moverse a través de lista de canales, presione arriba o abajo en las teclas de
navegación del mando.
2. Selección por número:
Introduzca directamente el número de canal a través del teclado numérico del mando,
y presione el botón "OK" para seleccionar el canal deseado.
3. Desde la lista de canales en pantalla:
También puede seleccionar el canal deseado directamente desde la lista de canales en
pantalla. Esta se muestra usando el menú principal del receptor. Para más detalles vea el
apartado "Lista de Canales" de este manual.
Acceder a la EPG
Acceder a la EPG de todos los canales:
1.
2.
3.
4.
Pulse la tecla "2"para cambiar entre lista de canales, lista de eventos del canal seleccionado y eventos actuales y siguientes.
EPG
Pulsar la tecla "EPG" del mando a distancia .
En la lista de eventos, pulse "OK"para programar el evento seleccionado, pulse "3" para abrir el menu detallado para el evento seleccionado..
1
0001 BBC NEWS 24 31 2004/03/23 10:55
0002 BBCi
Now: 10:30-11:00
BBC World News
0003 CBBC Channel
0004 BBC 2W
Next: 11:00-12:00
BBC News
Wednesday 2008/03/26
01 10:30-11:00 BBC World News
02 11:00-12:00 BBC News
03 12:00-13:00 BBC News
04 16:00-17:00 BBC News
Booking List
PG-+ Page
2
OK
Change
Play Booking
3
REC
Detail
Record Booking
Pulse la tecla "1"para abrir el menu de eventos programados.
Acceder a la lista de Favoritos
1.
2.
Pulse "FAV" para entrar en el menu de grupos de favoritos.
Pulse los cursores "ARRIBA" o "ABAJO" para seleccionar el grupo deseado.
Favorite
Group 1
Group 2
3.
Pulse "OK" para entrar en la lista de canales favoritos, y pulse los cursores
"ARRIBA" o "ABAJO" para elegir el canal favorito.
5
CANAL
Menú Lista de canales
1. Pulse MENU para entrar en el menú principal, seleccione Canal y pulse
"OK" para entrar en el menú canal.
2. Pulse "Arriba" o "Abajo" para seleccionar el item deseado y pulse "OK"
para entrar en el menú de configuración.
3. Pulse EXIT para salir
NOTA: Puede pulsar el botón OK para entrar en la lista de canales en modo reproducción.
Channel
TV Channel List
Radio Channel List
Delete All Favorites
Delete All
Group Rename
Select OK Enter EXIT Exit
Lista de canales de TV
1. En el menú Canal, seleccione "Lista de Canales de TV", pulse OK para
entrar en el menú lista de canales de de TV.
2. Pulse "Izquierda" o "Derecha" para seleccionar un grupo de canales. Pulse
Arriba o Abajo para previsualizar el canal de TV. Pulse OK para ver el canal
seleccionado a pantalla completa.
TV Channel List
All Channel
0 0 0 1 N E W S 2 4
0 0 0 2 B B C i
0 0 0 3 C B B C
0 0 0 4 B B C 2 W
0 0 0 5 T H R E E
0 0 0 6 Wa l e s
Editar
1 Edit
Group
2
PG-+
Find
Page
3 Sort
EXIT Exit
4 Move
Utilice este menú para bloquear, saltar y renombrar la lista de canales.
· En el menú lista de canales, pulse el botón 1 para entrar en el menú edición.
· Seleccione un canal y pulse OK para seleccionarlo. O pulse el botón
numérico "0" para seleccionar todos los canales. Los canales seleccionados
se marcarán con el símbolo " ".
· Pulse EXIT para salir del menú edición
OK
4
TV Channel List
A l l C h a n n e l
0 0 0 1 2 4
0 0 0 2 B B C i
0003 CBBC
0004 BBC 2W
0005 THREE
0006 Wales
Select
Delete
0
5
All
Rename
1 Favor
Group
Favoritos
TV Channel List
2
PG-+
Lock
Page
3 Skip
EXIT Exit
· En el menú "Editar Canal", pulse el botón "1", luego pulse Arriba o Abajo
para seleccionar el grupo deseado y pulse Ok para confirmar.
· Seleccione SI y pulse OK, el canal seleccionado será añadido al grupo de
canales.
Group 1
Group 2
0002 BBCi
Group 7
Group 8
Bloqueo
OK
4
Select
Delete
0
5
All
Rename
Yes
1 Favor
Group
2
PG-+
No
Lock
Page
3
EXIT
Skip
Exit
· En el menú "Editar Canal", pulse el botón "2", aparecerá una ventana de
confirmación. Seleccione "SI" pulse "OK", el canal seleccionado quedará
Switch lock channel. Are you sure?
bloqueado. Repita los pasos de arriba para desbloquear los canales bloqueados.
Saltar
Switch skip channel. Are you sure?
de arriba para cancelar los canales "saltados".
Yes No
· En el menú "Editar Canal", pulse "3", aparecerá una ventana de confirmación.
Seleccione SI, pulse OK, el canal seleccionado será bloqueado. Repita los pasos
Delete Channel. Are you sure?
Yes No
Borrar
En el menú "Editar Canal", pulse el botón numérico "4", aparecerá una
ventana de confirmación. Seleccione SI, pulse OK para borrar los canales
seleccionados de la lista de canales.
TV Channel List
A l l C h a n n e l
0 0 0 1 N E W S 2 4
0 0 0 2 B B C i
0003 CBBC
0004 BBC 2W
0005 THREE
0006 Wales
Find
A
H I
B
C D E F G
J K L M N
O P Q R S T U
V W X Y Z 1 2
3 4 5 6 7 8 9
0 ( sp DEL OK
Renombrar
1
En el menú "Editar Canal", pulse el botón "5" para abrir el teclado.
Introduzca letras y numeros uno a uno pulsando el cursor y pulsando OK para
confirmar. Después de confirmar, seleccione OK en el teclado para confirmar.
Edit
Group
2 Find
Page
3
EXIT
Sort
Exit
4 Move
Buscar
1. En el menú lista de canales, pulse el botón "2" para entrar en el menú Buscar.
2. Pulse el cursor para seleccionar los números y letras deseados y pulse OK para introducirlos
uno a uno. Después de introducir cada carácter, la lista de canales buscará el canal según lo
introducido y listará los canales que coincidan.
3. Pulse EXIT para salir del menú Buscar.
1
Español
CANAL
Lista de canales de TV (Continuación)
Ordenar
1. En el menú lista de canales, pulse el botón "3" para entrar en el menú
Ordenar.
2. Pulse Arriba o Abajo para seleccionar la manera deseada de ordenación
y pulse "OK" para confirmar.
Por defecto: Ordenación por búsqueda
Nombre (A-Z): Ordenación alfabética
Nombre (Z-A): Ordenación alfabética
FTA: Guarda todos los canales libres
Bloqueo: Acumula todos los canales bloqueados y los lista al final de la lista de canales.
Mover
1. En el menú Lista de canales, pulse el botón "4", los canales
seleccionados serán marcados con el símbolo " ". Pulse Arriba o Abajo
para mover el canal seleccionado a la posición que desee colocar.
2. Pulse "OK", aparecerá una ventana de confirmación. Seleccione SI,
pulse "OK" para cambiar el orden del canal.
Lista de canales de Radio
1. En el menú Canales, seleccione "Lista de Canales de Radio", pulse OK
para entrar en el menú lista de canales de radio.
2. Pulse Izquierda o Derecha para seleccionar el grupo de canales. Pulse
Arriba o Abajo para seleccionar el canal deseado, y pulse OK para
escuchar el canal.
NOTA:
Basicamente el funcionamiento de la Lista de Canales de Radio es el mismo que el funcionamiento de la Lista de Canales de TV. Solo existe una diferéncia, en la Lista de
Canales de Radio no aparece información de video, solo aparece el logo de Radio en el lado derecho de la ventana de previsualización
TV Channel List
All Channel
0002 BBCi
0003 CBBC Channel
Name(A-Z)
0005 BBC THREE
FTA
Lock
1 Edit
Group
2 Find 3
PG-+ Page EXIT
Sort
Exit
4 Move
TV Channel List
All Channel
0 0 0 1 N E W S
0 0 0 2 B B C i
0003 CBBC
0004 BBC 2W
0005 THREE
0006 Wales
1 Edit
Group
2 Find
PG-+ Page
3 Sort
EXIT Exit
4 Move
Radio Channel List
All Channel
0 7 0 0 R a d i o 1
0 7 0 2 R 5 L i v e
0703 Radio 2
0704 Radio 3
0705 Radio 4
0706 SportsX
0707 6 Music
1 Edit
Group
2 Find
PG-+
Page
3
EXIT
Sort
Exit
4 Move
Borrar todos los favoritos
Utilize este menú para borrar los canales favoritos.
1. En el menú Canal, seleccione "Borrar todos los Favoritos", pulse OK,
aparecerá una ventana de aviso.
2. Seleccione SI y pulse OK para borrar todos los canales favoritos
Seleccione NO y pulse OK para cancelar el borrado.
Channel
TV Channel List
Radio Channel List
Borrar todo
Utilice este menú para borrar todos los canales.
1. En el menu Canal, seleccione "Borrar Todo", pulse el botón OK, se le
pedirá que introduzca la contraseña (la contraseña por defecto es 0000)
2. Introduzca la contraseña, aparecerá una ventana de aviso. Seleccione SI,
pulse OK para borrar todos los canales.
Seleccione NO, pulse OK para cancelar .
Warning: Do you really want to delete all channels ?
Yes No
Select OK Enter
No
EXIT Exit
Channel
TV Channel List
Radio Channel List
Delete All
- - - -
-
Group Rename
Select OK Enter EXIT Exit
Renombrar Grupo
Utilice este menú para cambiar el grupo de canales.
1. En el menú canal, seleccione "renombrar grupo",
pulse OK para entrar en el menú renombrar grupo.
2. Seleccione el grupo deseado, pulse OK para abrir
el teclado. Introduzca las letras y los numeros uno
a uno pulsando el cursor y pulse OK para confirmar.
Una vez acabado, pulse OK en el teclado para
confirmar.
3. Pulse EXIT para salir del menú Renombrar grupo.
7
Español
Group Rename
Group 1
Group 2
Group 3
Group 4
Group 5
Group 6
Group 7
Group 8
Select OK Rename EXIT Exit
Group Rename
Group 1
Group 2
Group 3
Group Rename
Group 1_
Group 4
Group 5
Group 6 g h i j k l m n o p q r
Group 7 s t
1 2 3 4 5 6 7 8 9
!
u v w x y z
`
Group 8
Select OK Rename EXIT Exit
CONFIGURACION DEL SISTEMA
Menú de Configuración del sistema
El menú configuración del sistema, le permite configurar el idioma OSD, el sistema de TV, la zona horaria, configuración del Temporizador, configuraciones del OSD, bloqueo paterno y .
1. Pulse MENU para entrar en el menú principal, seleccione "Configurar"
y pulse OK para entrar en el menu de configuración del sistema,
2. Pulse "Arriba" o "Abajo" para seleccionar el menú deseado y pulse OK
para entrar en el menú configuraciones. Pulse Arriba o Abajo para
seleccionar el item deseado, pulse "Izquierda" o "Derecha" para
cambiar la configuración.
3. Pulse EXIT para salir.
System Setup
OSD Language
TV System
Region and Time
Timer Setting
OSD setting
Parental Lock
Standby Mode
Select OK Enter EXIT Exit
Idioma de los menús
Este menú le permite configurar el idioma del OSD o menú en pantalla.
Idioma OSD: Para seleccionar el OSD deseado.
OSD Language
OSD Language English
Change EXIT Exit
Sistema de TV
Este menu permite configurar modo Display, Aspecto, Salida Video y Modo LCN.
TV System
Modo Display: NTSC/AUTO/PAL
Aspecto: 4:3PS/4:3LB/16:9/Auto
Salida de Video: RGB/CVBS
Modo LCN: Si el LCN está activado, no podrá cambiar el
número de los canales de TV. Puede activar o
desactivar la función LCN, poniendo LCN a
Display Mode
Aspect Radio
Video Output
LCN Mode
ON o OFF.
Select Change
Auto
4:3LB
RGB
Off
EXIT Exit
Configuración de Hora local
Este menú le permite configurar la hora local.
Zona horaria: Este menú se utiliza para cambiar la zona horaria.
Uso GMT: Este menú se utiliza para abrir el uso GMT
Las opciones son: OFF/Definidas por usuario/Por zona.
Region and time
Region
GMT Usage
GMT Offset
Date
Time
Time Display
France
By Region
GMT+01:00
2004/03/23
10:56
Off
Offset GMT: Este menú es solo válido cuando seleccione "Definidas
por el usuario" en el menu uso GMT. El rango de offset
GMT es -11:30 ~+12:00, incrementando media hora
progresivamente.
Select OK Enter EXIT
Fecha: Los menús Fecha y Hora solo son válidos cuando seleccione "OFF" en el menu
Uso GMT.
Hora: Pulse OK y los botones numéricos para cambiar la fecha y la hora.
Exit
Mostrar Hora: Este menú le permite si desea mostrar la hora en la pantalla o no.
Las opciones son: Encendido/Apagado
1
Español
CONFIGURACION DEL SISTEMA
Configuración del Temporizador
Este menú le permite configurar el temporizador y la opción apagado automático.
Temporizador: Este menú es utilizado para configurar el temporizador de los
programas que desea cambiar.
Numero de temporizador: Puede configurar 8 temporizadores.
Modo de temporizador: Apagado/Una vez/Diario/Semanal/Mensual
Tipo de temporizador: TV/Radio
Canal de encendido: Puede seleccionar el canal que desea que aparezca al
encender el receptor.
Program Timer
Tuesday xxxx/xx/xx xx:xx
Timer Number
Timer Mode
Timer Service
Wakeup Channel
Month
Date
Day
Time
1
Once
TV Service
BBC NEWS 24
3
23
Tuesday
10:57
Select OK Enter EXIT Exit
Mes/Fecha/Dia: Pulse Izquierda o Derecha para seleccionar el
mes deseado, la fecha y el dia.
Hora: Pulse OK y los botones numéricos para
introducir la hora.
Grabación automatica: ACT significa que es un temporizador de
Program Timer
Tuesday xxxx/xx/xx xx:xx
Auto Record
Record Duration
Off
02:00 grabación . Si lo desactiva, será un temporizador de visualizado.
Duración: Presione "OK" y los botones numéricos para
introducir la duración del temporizador.
Cuando desee salir del temporizador, una ventana para que se grabe aparecerá.
Select
OK
Enter
EXIT
Exit
Sleep Timer
Sleep Timer
Remains
Change
Off
00:00
OK Start Timer
Temporizador de apagado: Puede configurar el receptor para
que se apague en 10 min, 30 min, 60 min, 90 min o 120 min. automáticamente.
EXIT Exit
Configuración del OSD
Este menú le permite configurar los subtítulos, la transparencia del
OSD y cargar la configuración del OSD por defecto.
Subtítulos: Para configurar los subtítulos como Standard/Apagado/
Teletexto.
Transparencia del OSD: Para configurar la transparencia del OSD
Apagada/10%/20%/30%/40%/50%
Cargar Configuraciones OSD por defecto: Para borrar todas las configuraciones OSD y los parámetros con los valores por defecto.
OSD Setting
Subtitle Display
OSD Transparency
Load Default OSD Setting
Select Change
Off
10%
EXIT Exit
Control parental
Parental Lock cambiar de contraseña.
1. En el menu "Configuración del Sistema", seleccione "Bloqueo
paterno" y pulse el botón OK, se le pedirá una contraseña (la
contraseña por defecto es 0000).
2. Después de introducir la contraseña pulsando los botones
numéricos, aparecerá el menú de bloqueo paterno.
Menu Lock
Channel Lock
New Password
Confirm Password
Select
Off
Age:4
----
----
Change 0-9 Input EXIT Exit
Bloqueo de menú: Para bloquear el menú instalación, cuando desee entrar en el menú Auto
Scan / Channel Scan, deberá introducir la contraseña. Puede configurar
el bloqueo de menú como ON/OFF.
Nueva contraseña: Para cambiar la contraseña.
Confirmar contraseña: Para confirmar la nueva contraseña.
Apagado automático
On En caso de falta de comandos desde el panel frontal o desde el mando a distancia durante 3 horas y sin eventos programados el aparato se apagará automáticamente (irá a stand-by).
Auto Standby
Auto Standby
Off El aparato no se apagará automáticamente en ningún caso.
On
Select
OK Enter
EXIT Exit
9
Español
HERRAMIENTAS
Menú principal de Herramientas
"Herramientas", pulse OK para entrar en el menú de herramientas.
2. Pulse ARRIBA o ABAJO para seleccionar el menú deseado y
pulse OK para entrar.
3. Pulse EXIT para salir.
Tools
Receiver Information
Game
Load Factory Default
Software Upgrade
Select
OK
Enter
EXIT
Exit
Información del receptor
Este menú puede mostrar algunos parámetros del receptor y del software de este receptor.
1. En el menú "Herramientas", seleccione "Información del Receptor",
pulse OK para abrir la ventana de información del receptor.
Receiver Information
Receiver
Software
Signature
DVB-T xxxx xxx_x_xxxxxx_xx_xxx xxx xx xxxx xx:xx:xx
EXIT Exit
2. Pulse "EXIT" para salir.
Juegos
1. En el menú "Herramientas", seleccione "Juegos", pulse OK para
entrar en el menú Juegos
2. Pulse "Arriba" o "Abajo" para seleccionar el juego deseado, y pulse
el botón OK para entrar en el juego. Seleccione "Empezar" y pulse
"OK" para empezar el juego.
3. Pulse el botón "EXIT" para
salir del juego.
NOTA: También puede pulsar "OK" para pausar el juego
Restablecer configuración de fábrica
1. Este menú le permite resetear su receptor, pulse OK y se le
pedirá una contraseña.
2. Introduzca la contraseña correcta, utilizando los botones
numéricos (la contraseña por defecto es 0000).
3. Seleccione "SI" para volver a la configuración de fábrcia.
Seleccione "NO" para cancelar la configuración de fábrica.
4. Pulse "EXIT" para salir.
Game
Tetris
Snake
Othello
Select
OK
Enter
EXIT
Exit
Tools
Receiver Information
Game
Load Factory Default software Upgrade
Yes No
Select
OK
Enter
EXIT
Exit
Actualización de software
Le ofrecemos las funciones para actualizar la versión de software por aire o a través de una memoria USB.
1. Entre en el menú "Herramientas", seleccione "Actualización de
software", pulse OK, aparecerá el menu de actualización de
software.
2. Pulse el botón "OK", se le pedirá que introduzca una
contraseña.
3. Introduzca la contraseña correcta (la contraseña por defecto es
0000), aparecerá el submenú de actualización de software.
4. Pulse EXIT para salir.
10
Español
Software Upgrade
Upgrade By Air
Upgrade By Storage
Select
OK
Enter
EXIT
Exit
2
Media+
Menú principal de Media+
1. Presione el botón "MENÚ" para entrar en el menú principal.
Seleccione " Media + ", y pulse el botón "OK" para entrar el
menú de Media +.
2. Pulse el botón "Arriba" o "Abajo" seleccionar el artículo
deseado, luego pulse el botón "OK" para entrar.
3. Pulse el botón "Exit" para salir.
Media+
Media Player
Record Manage
Removable Disk Information
DVR Configuration
Safely Remove Storage Device
Disk Format
Select
OK
Enter
EXIT
Exit
Reproductor Multimedia
Esta función le permite reproducir archivos de video , audio o archivos de foto desde dispositivos conectados al puerto de USB.
1. En el menú "Media +", seleccione "Media Player /
Reproducir", y pulse el botón "OK" para entrar en el menú
de Reproductor MultiMedia .
2. Pulse el botón "Arriba" o "Abajo" seleccionar el artículo
deseado, luego pulse el botón "OK" para reproducir.
3. Pulse el botón "Exit" para salir.
Gestor de grabaciones
Este menú le permite reproducir las grabaciones que haya efectuado.
1. En el menú "Media +", seleccione "Gestor de grabaciones", pulse
botón "OK" para entrar en el menú
luego pulse el botón "OK" para reproducirlo.
3. Pulse el botón "Exit" para salir.
.
Media Player: USB/Partition1
001 Autorun.inf
002 ALiDvr
I swear.mp3
I swear.mp3
00:03:15 00:04:10
ImgList Music List Image List Setup
Record Manage
SVT1 (DVR)
15:39-15:40(00:01:01) 37M
Sort
No. Date Time Name
0001 01/01 01:01-01:02 SVT1
0002 30/08 15:39-15:40 SVT1
0003 10/05 17:41-17:42 France3
0004 01/01 01:00-01:01 France5
1 Lock 2 Delete 3 Rename 4 Information
Información del disco extraible
Este menú le permite mostrar algunos parámetros del disco extraible conectado al puerto USB.
1. En el menú "Media +", seleccione "Información del disco extraible"
2. Pulse el botón "Exit" para salir.
.
Removable Disk Information
Device
Total
Free
Used
TimeShift
Rec Free
File System xxxxxx x.xx GB x.xx GB x.xx GB x.xxGB
x.xxGB
FAT
EXIT Exit
Configuración DVR
Este menú le permite fijar la configuración del DVR o grabador.
Pulse el botón "Arriba" o "Abajo" para seleccionar el elemento deseado y pulse "Izda." o "Dcha." para modificarlo.
Duración TimeShift (min)
Tamaño maximo de Timeshift es 1 h.
TS: Transport Stream, que incluye información de teletexto, subtítulos,
EPG, etc.
PS: Program Stream, que empaquetará el fichero en formato *.mpg y
podrá ser reproducido en PC y otros dispositivos.
Modo Stand-by Off/on
Off: Cuando acabe la grabación, el receptor no irá a reposo (stand-by)
DVR Configuration
Preferred Storage
TimeShift time(min)
Record Type
Standby Mode
EXIT Exit
1 E spañol xxxxxx
20
TS
Off
Media+
Extraccion segura del dispositivo USB
En el menú de "Media +" , seleccione "Quite con seguridad el dispositivo de almacenamiento", y pulse el botón "OK" para confirmar.
Aparecerá una ventana de confirmación.
Please select operation
Safely remove USB storage device
Cancel
Formateo de disco
Este menú le permite formatear la memoria o disco duro USB.
Vaya a "Sistema de archivos" y pulse el cursor "IZDA" o "DCHA" para cambiar el ajuste entre FAT y NTFS.
Una vez seleccionado el sistema de archivos en que desea formatear el disco USB, pulse "OK" y una ventana de aviso se mostrará:
Disk Format
Device
Capability
File System
EXIT Exit
Elija "SI" y pulse "OK" para formatear.
Elija "NO" y pulse "OK" para cancelar.
Start xxxxxx xxxx MB
FAT
WARNING: Format will delete ALL data in this disk,
Continue?
Yes No
1 E spañol
Grabacion/Time Shift
Al conectar un dispositivo de almacenamiento masivo externo en el puerto USB ya podrá grabar
Pare un programa en directo y continue viéndolo más tarde (Timeshift).
Cuando el espacio disponible en el dispositivo de almacenamiento masivo se agota, la grabacion se detendrá.
.
NOTA:
P or favor use un disco USB 2.0 cuando graba o haga timeshift drive o HDD de tamaño más grande a 2GB .
.
Para Timeshift y función de grabación, necesita tener un pen
Timeshift (Grabacion en pausa)
Inicio del Timeshift
Para comenzar el Time Shift, pulse la tecla "TIMESHIFT " mientras ve un programa.
Pulse la tecla "DCHA. " o "IZDA." para mover el cursor hasta la parte que se desea ver.Pulse "OK " para confirmar.
Otras funciones del TimeShift
Durante la reproducción del Timeshift, también se puede hacer:
Pulsar "PAUSE "para hacer una pausa en la reproducción.
Pulsar "FWD " para avanzar rápidamente.
Pulsar "REV para retroceder rápidamente.
9 BBC FOUR
Parar el TimeShift
31
03/19 01:36
00:02:37/00:07:12 TimeShift
You will quit timeshift, are you sure ?
Yes No
PS
0%
Pulse "EXIT/CH+/CH- " para parar el TimeShift,y aparecerá una ventana de confirmación. Elija Si para volver a modo normal de visualización mostrando el programa en directo. Elija NO para continuar en Timeshift.
Grabar el Time Shift
Cuando quiera grabar el TimeShift, pulse "RECORD " y aparecerá una ventana de confirmación .
Selecione SI para grabar el Time Shift almacenado y también el programa en directo.
Seleccione NO para grabar el programa en directo solamente.
You will quit timeshift, do you want to save all the buffer data to disk?
Yes No
Grabar
Hay tres maneras de grabar programas:
Grabación Instantánea
Mientras ve un canal, pulse "RECORD" y una ventana de confirmación aparecerá aparecerá. Seleccione SI para parar la grabación.
Desde el EPG
Please select operation
.
Continue recording
Pulse "RECORD " con un evento seleccionado para grabarlo.
EPG
Se mostrará un icono al lado del evento programado.
Pulse "RECORD " para cancelar el evento programado.
Programación manual
0001 BBC NEWS 24 31
2004/03/23 10:55
0002 BBCi
0003 CBBC Channel
Now: 10:30-11:00
BBC World News
Next: 11:00-12:00
0004 BBC 2W
BBC News
Wednesday 2008/03/26
01 10:30-11:00 BBC World News
02 11:00-12:00 BBC News Puede programar grabaciones desde el menú de temporizadores.
03 12:00-13:00 BBC News
04 16:00-17:00 BBC News
1 Booking List
PG-+ Page
2
OK
Change
Play Booking
3
REC
Detail
Record Booking
13
Español
PROBLEMAS COMUNES
En algunas zonas, la señal de la televisión digital terrestre puede ser débil.
Problema
El led standby no se enciende
No ha encontrado señal
Posible causa
El cable de alimentación está desconectado El fusible de alimentación está fundido
Solución
Compuebe el cable de alimentación
Compruebe el fusible
La antena está desconectada
La antena está dañada o mal alineada
No tiene cobertura de señal digital
Compruebe la alimentación de antena
Compruebe la antena
Consulte con su distribuidor
No hay imagen ni sonido La entrada SCART no está seleccionada en su TV
Aparece un mensaje de canal codificado
El canal está codificado
Seleccione la entrada de video adecuada en su TV
Seleccione un canal alternativo
No existe respuesta en el mando a distáncia
El receptor está apagado
El mando no apunta en la dirección correcta
El panel frontal está obstruido
Las pilas están agotadas
Enchufe de nuevo el equipo y enciendelo
Dirija el mando al panel frontal
Compruebe los obstáculos
Cambie las pilas del mando
Ha olvidado el código de bloqueo de canal
Reinstale los canales para cancelar el bloqueo de canales
Ha olvidado el código de bloqueo de menús
Contacte con su distribuidor
El mando a distancia no funciona con el receptor
1. Las pilas deben ser cambiadas
2. Existe un objeto que bloquea la señal entre el mando a distancia y el receptor
1. Cambie las pilas
2. Compruebe que no hay nada entre
el mando y el receptor
Después de mover el receptor a otra habitación, comprueba que ya no recibe la señal digital
La nueva toma donde se ha conectado el receptor, puede que tenga una distribución diferente que haga que la calidad de la señal digital recibida sea menor.
Pruebe una alimentación directa de la antena.
14
Español
SET TOP BOX
Digital receiver
TDT-130
OWNER'S MANUAL
Read this manual before installation and use.
English
SAFETY INFORMATION
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
CAUTION
: To reduce the
risk of fire and electric shock, do
not remove the cover (or back) of
10.
the unit. Refer servicing only to qualified service personnel.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
11.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operation and servicing instructions in the literature accompanying the appliance.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids ,such as vases shall be placed on the apparatus.
Caution: Maintain electrical safety. Powerline operated equipment or accessories connected to this unit should bear safety certification mark on the accessory itself and should not be modified so as to defeat the safety features. This will help avoid any and should not be modified so as to defeat the safety features. This will help avoid any potential hazard from electrical shock or fire. If in doubt, contact qualified service personnel.
IMPORTANT SAFEGUARDS
Accessories- Do not place this video product on an unstable cart, stand, tripod, bracket, or table. The video product may fall, causing serious injury to a child or adult as well as serious damage to the video product. Use this video product only with a cart, stand, tripod, bracket, or table recommended by the manufacturer's or sold with the video product. Any mounting of the product should follow the manufacturer's instructions and use of a mounting accessory recommended by the manufacturer.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT AND FULLY INSERT.
The apparatus shall not be exposed to dripping or splashing, and that no objects filled with liquids, such as vases, shall be place on the apparatus.
In addition to the careful attention devoted to quality standards in the manufacture of your video product, safety is a major factor in the design of every instrument. However, safety is your responsibility, too. This sheet lists important information that will help to assure your enjoyment and proper use of the video product and accessory equipment. Please read them carefully before operation and using your video product.
12.
11a.
A video product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the video product and cart combination to overturn.
Note to CATV system installer
This reminder is provided to call the CATV system installer's attention to
Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
Outdoor Antenna Grounding- If an outside antenna or cable system is connected to the video product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No.70-1984 (Section 54 of Canadian
Electrical Code, Part1) provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antennadischarge unit, connection to grounding electrodes, and requirements for the grounding electrode.
Installation
1.
Read and Follow Instructions- All the safety and operation instructions should be read before the video product is operated. Follow all operating instructions.
14.
2.
Retain Instructions- The safety and operating instructions should be retained for future reference.
15.
3.
Heed all Warnings-Comply with all warnings on the video product and in the operating instructions.
16.
4.
Polarization- Some video products are equipped with a polarized alternating -current line plug. This plug will fit into the power outlet, try reversing the plug. If the plug still fails to fit, contact your electrician to replace your obsolete outlet. To prevent electric shock, do not use this polarized plug with an extension cord, receptacle, or other outlet unless the blades can be fully inserted without blade exposure. If you need an extension cord, use a polarized cord.
17.
13.
Power Lines-An outside antenna system should not be located in the vicinity of overhead power lines, other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching or approaching such power lines or circuits, as contact with them might be fatal. Installing an outdoor antenna can be hazardous and should be left to a professional antenna installer.
Use
Cleaning- Unplug this video product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Objects that may touch dangerous voltage points or "short-out" parts could result in a fire or electric shock. Never spill liquid of any kind on the video product.
Lightning-For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the video product due to lightning and power line surges.
Service
Servicing-Do not attempt to service this video product yourself, as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
5.
Power Sources- This video product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your video dealer or local power company. For video products intended to operate from battery power, or other sources, refer to the operating instructions.
18.
6.
Overloading- Do not overload wall outlets or extension cords as this can result in a risk of fire or electric shock. Overloaded AC outlets, extension cords, frayed power cords, damaged or cracked wire insulation, and broken plugs are dangerous, They may result in a shock or fire hazard.
Periodically examine the cord, and if its appearance indicated damage or deteriorated insulation, have it replaced by your service technician.
Conditions Requiring Service-Unplug this video product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
A. When the power-supply cord or plug is damaged.
B. If liquid has been spilled, or objects have fallen into the video product.
C. If the video product has been exposed to rain or water.
D. If the video does not operate normally by following the operating
instructions.
Adjust only those controls that are covered by operating instructions.
Improper adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the video product
to its normal operation.
E. If the video product has been dropped or cabinet has been damaged.
F. When the video product exhibits a distinct change in performance-this
indicates a need for service.
7.
Power-Cord Protection- Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the video product.
Where the MAIN plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
19.
Replacement Parts-When replacement parts are required, have the service technician verify that the replacements he uses have the same safety characteristics as the original parts. Use of replacements specified by the video product manufacturer can prevent fire, electric shock, or other hazards.
8.
Ventilation- Slots and openings in the case are provided for ventilation to ensure reliable operation of the video product and to protect it from overheating. These openings must not the blocked or covered. The openings should never be blocked by placing the video product on a bed,
20.
sofa, rug, or heat register. This video product should not be placed in a built-in installation such as a book case or rack, unless proper ventilation is provided or the video product manufacturer's instructions have been followed.
21.
22.
9.
Attachments- Do not use attachments unless recommended by the video product manufacturer as they may cause hazards.
Safety Check-Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks recommended by the manufacturer to determine that the video product is in safe operating condition.
Wall or Ceiling Mounting- The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
Heat-The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that products heat.
CONTENTS
SAFETY INFORMATION
INTRODUCTION
About the STB
SYSTEM CONNECTION
General
Connecting to the TV and a video recorder
Connecting a HiFi system
GETTING STARTED
Easy Install
Installation
Auto Scan
Channel Scan
Tuner Setting
OPERATION
Changing Channels
Accessing the Electronic Program Guide (EPG)
Accessing the favorite channels
CHANNEL
Channel list menu
TV Channel List
Radio Channel List
Delete All Favorites
Delete All
Group Rename
SYSTEM SET-UP
System setup menu
OSD Language
TV System
Region and Time
Timer Setting
OSD Setting
Parental Lock
Auto Standby
TOOLS
Tools main menu
Receiver Information
Game
Load Factory Default
Software Upgrade
Media+
Media+ main menu
Media Player
Record Manage
Removable disk information
DVR configuration
Safely Remove Storage Device
Disk Format
Timeshift/ Record
Timeshift
Record
TROUBLESHOOTING
SPECIFICATIONS
11
11
11
11
11
12
12
13
13
10
10
10
10
10
9
9
9
9
8
8
8
8
6
7
7
6-7
7
7
4
4
4
4
4
3
3
3
5
5
5
15
16
INTRODUCTION
About STB
Front panel
Remote sensor Power indicate
USB port
Rear panel
RF Input for an external aerial
Coaxial Digital Audio
TV Scart for connection to your TV
AC Mains
RF Loop through for an external device
1 English
INTRODUCTION
Remote control
STANDBY MUTE
5 Cursor: Navigation buttons used to
navigatemenus items
1 14
2
3
1
4
7
INFO
MENU
2
5
8
0
EPG
AUDIO
6
SUBTITLE
9
RECALL TV/RADIO
EXIT
15
16
17
18
19
20
6 OK button
(Confirm a selection within a menu)
7 RECORD
(Record the TV program)
8 VOL+,-
(VOL+/-:Volume Up and Down)
9 TTX (Open interactive service)
10 SLEEP (Open the sleep timer list)
11 TIMESHIFT
(Active timeshift function)
4
5
6
7
8
9
10
11
9
12
13
13
RECORD
VOL
FILE
TTX
TIMESHIFT SLEEP
OK
FAV
PLAY
GOTO PAUSE
STOP
CH
REV
FWD
21
22
23
24
25
26
27
28
1
2
3
4
STANDBY
(switch the STB on and standby)
Numeric entry
(Enter numeric values and select the channel directly by entering it's number)
INFO
(Press for current channel information )
Menu
(Open and close the menu screen)
1 English
12 FILE
(Enter Record List)
13 GOTO (Selects the play time of media)
14 MUTE (Turn off/on the volume)
15
EPG
(Open up Electronic Program Guide Menu)
16
AUDIO
(Select audio mode and audio track)
17 SUBTITLE (On/Off Subtitle)
18
TV/RADIO
(Switch between TV and Radio)
19
RECALL
(Switch to previous channel)
20 EXIT (Exit from menu)
21
22
STOP
CH+,-
(CH+/-: Channel Up and Down
23 FAV
(Open the Favorite list)
24 REV
(Press REV button to rewind the playback)
25
26
PLAY
FWD
(Press FWD button to fast forward the playback)
27 PAUSE(Pause/Active timeshift function)
28 RED/GREEN/YELLOW/BLUE Buttons
(For interactive function/Submenu
function buttons)
SYSTEM CONNECTION
General
There are many different types of TV and other equipment that you can connect to the STB.
In this manual you will see some of the most common ways to connect your equipment.
Connection to the TV and video recorder with SCART
Scart cable
Antenna
RF cable
TV
Connecting a HiFi system
Hi-Fi
Coaxial cable
3 English
GETTING STARTED
Easy Install
If you use the STB for the first time, the "Easy Install" menu appears .
Press "LEFT" or "RIGHT" cursor button to setup the Region and OSD Language.
Highlight "Search ",press the "OK" button to start channel search.
Easy Install
Region
OSD Language
Search
Spain
English
Select OK Enter EXIT Exit
Installation
1 Press the "MENU" button to enter main menu.
Installation
2 Press " LEFT"or " RIGHT " to select "Installation", press "OK" button to enter the Installation menu.
Auto Scan
Channel Scan
Power Control
3 Press "EXIT" button to exit.
Select OK Enter EXIT Exit
Auto Scan
1
2
Press" UP" or " DOWN " to select t he "Auto Scan", press "OK" button to enter the Auto Scan menu.
Press the "LEFT" or "RIGHT" cursor button to select Scan mode, and highlight
"Search" ,then press the "OK" button to start auto scan .
Auto Scan
TV Channel List
2 BBCi
3 CBBC Channel
4 BBC 2W
5 BBC THREE
6 BBC ONE Wales
Radio Channel List
1 BBC Radio Wales
2 BBC Radio Cymru
UHF: 470.0-862.0 MHz Ch No: GI:
Frequency: 490.00 Mhz Modulation: FFT:
24%
EXIT Exit
Channel Scan
1
2
Press " UP" or " DOWN " to select "Channel Scan" and press the "OK" button to enter the Channel Scan menu.
Press "LEFT" or "RIGHT" cursor button to select Scan mode, Scan Band and Channel No. and highlight "Search", then press "OK" button to start channel scan .
Channel Scan mode:
By channel
By frequency
Channel Scan
Scan Mode
Scan band
Ch No.
Frequency
Band Width
Network Search
By Channel
UHF
22(482.000MHz)
482.000
8 MHz
Off
Search
Signal Intensity
Signal Quality
Select OK Enter EXIT
94%
97%
Exit
Power Control
Press" UP" or " DOWN " to select t he "Power Control", press "OK" button to enter the Power Control menu.
Tuner Power: On/Off
RF Loop-through: On/Off
Power Control
Tuner Power Off
RF Loop-through Off
Change EXIT Exit
4 English
OPERATION
Changing Channels
There are four ways of channel selection - stepping through the channel list, selection by number, from the on-screen channel list, and using the electronic programme guide(EPG).
1 Stepping through the channel list:
To move through the channel list, press the upward arrow or downward arrow key on the
remote control.
2
3
Selected by number:
Enter the channel number directly by pressing numeric buttons ,and press the "OK" button
to select desired channel.
Selected by on-screen channels list:
You can also select the required channel directly from on-screen channel list. This is
displayed using the STB's main menu. See "Channel List" in this manual for operation detail.
4 Selected by EPG:
You can also select the required channel directly from electronic program guide (EPG).
This is displayed using the STB's main menu. See "Accessing the Electronic Program Guide
(EPG)" in this manual for operation detail.
Accessing the Electronic Program Guide (EPG)
Accessing the EPG of all channels:
1
2
3
4
Press "EPG" button to enter EPG menu .
Press numeric button"2" to switch between channel list, events schedule of the selected channel and now/next events.
In the event schedule, press "OK" button to book the selected event, press numeric button "3" to open the Detail menu for the selected event.
EPG
1
0001 BBC NEWS 24 31 2004/03/23 10:55
0002 BBCi
Now: 10:30-11:00
BBC World News
0003 CBBC Channel
0004 BBC 2W
Next: 11:00-12:00
BBC News
Wednesday 2008/03/26
01 10:30-11:00 BBC World News
02 11:00-12:00 BBC News
03 12:00-13:00 BBC News
04 16:00-17:00 BBC News
Booking List
PG-+ Page
2
OK
Change
Play Booking
3
REC
Detail
Record Booking
Press numeric button "1" to open the Booking list menu.
Accessing the favorite channels
1
2
3
Press "FAV" button to enter favorite group menu.
Press "UP" or "DOWN" cursor button to select the desired favourite group.
Press "OK" button to enter the favorite channels list, and press "UP" or "DOWN" cursor button to select the favorite channel.
Favorite
Group 1
Group 2
5 English
CHANNEL
Channel list menu
1 Press "MENU" button to enter the main menu, select "Channel" and press "OK" button to enter Channel menu.
2
3
Press "UP" or "DOWN" cursor button to highlight the desired item and press "OK"button to enter the setting menu .
list in normal playback mode.
Press "EXIT" button to exit.
Channel
TV Channel List
Radio Channel List
Delete All Favorites
Delete All
Group Rename
Select OK Enter EXIT Exit
TV Channel list
1 In the Channel menu, select "TV Channel List", press "OK" button to enter TV channel list menu.
TV Channel List
All Channel
0 0 0 1 N E W S 2 4
0 0 0 2 B B C i
0 0 0 3 C B B C
0 0 0 4 B B C 2 W
0 0 0 5 T H R E E
0 0 0 6 Wa l e s
2 Press "LEFT" or "RIGHT" cursor button to select channel group. And press "UP" or "DOWN" cursor button to preview the desired TV channel. Press the "OK" button to view the selected channel in full screen.
1 Edit
Group
2
PG-+
Find
Page
3 Sort
EXIT Exit
4 Move
Edit
Use this menu to favor, lock, skip ,delete and rename channel list.
In channel list menu, press numeric button "1" to enter edit menu.
Highlight a channel and press "OK" button to select it . Or press numeric button "0" to select all channels. And the selected channels will be marked in a symbol " ".
TV Channel List
A l l C h a n n e l
0 0 0 1 2 4
0 0 0 2 B B C i
0003 CBBC
0004 BBC 2W
0005 THREE
0006 Wales
OK
4
Select
Delete
0
5
All
Rename
1 Favor
Group
2
PG-+
Lock
Page
3 Skip
EXIT Exit Press "EXIT" button to quit the edit menu.
Favor:
In "Edit Channel" menu, press numeric button "1", then press "UP" or "DOWN" cursor button to select a desired group, and press "OK" button, a confirmation window appears.
TV Channel List
Group 1
Group 2
0002 BBCi
Select "Yes" and press "OK" button, the selected channel will be added to the group.
Group 7
Group 8
Lock:
In "Edit Channel" menu, press numeric button "2", a confirmation window appears.
Select "Yes", press "OK" button, the selected channel will be locked .Repeat steps above to unlock the locked channels.
OK
4
Select
Delete
0
5
All
Rename
1 Favor
Group
2
PG-+
Lock
Page
3 Skip
EXIT Exit
Switch lock channel. Are you sure?
Yes No
Skip:
In "Edit Channel" menu, press numeric button "3", a confirmation window appears.
Select "Yes", press "OK" button, the selected channel will be skipped while you change the channel in full screen. Repeat steps above to cancel the skipped channels.
Switch skip channel. Are you sure?
Yes No
Delete: Delete Channel. Are you sure?
Yes No
In "Edit Channel" menu, press numeric button "4" ,a confirmation window appears.
Select "Yes", press "OK" button to delete the selected channels from channel list.
Rename:
In "Edit Channel" menu, press numeric button "5" to open the mock keypad. Input letter and numeric one by one by pressing the cursor button and press "OK" button to confirm. After finishing input, highlight "OK" on mock keypad to confirm, you change name successfully.
Find
1
2
3
In channel list menu, press numeric button "2" to enter Find menu.
Press cursor button to highlight desired letters or numbers and press "OK" button to input one by one. After input each character, the channel list will search the channel according your input and list the matched channel.
TV Channel List
A l l C h a n n e l
0 0 0 1 N E W S 2 4
0 0 0 2 B B C i
0003 CBBC
0004 BBC 2W
0005 THREE
0006 Wales
Find
A B C D E F G
H I J K L M N
O P Q R S T U
V W X Y Z 1 2
3 4 5 6 7 8 9
0
( sp DEL OK
Pressing the "EXIT" button to quit "Find" menu.
1 Edit
Group
2 Find
Page
3 Sort
EXIT Exit
4 Move
6 English
CHANNEL
TV Channel list (Continued)
Sort
1 In channel list menu, press numeric button "3" to enter "Sort" menu.
TV Channel List
All Channel
2 Press "UP" or "DOWN" cursor button to highlight desired sort way and press "OK" button to confirm.
Default:
Name (A-Z):
Name (Z-A):
FTA:
Lock:
Sorting by scanning result.
Sorting in Alphabetical Order.
Sorting in Alphabetical Order.
Sieving out all free fare channels.
Accumulating all locked channels and list in the last of TV Channel List.
0002 BBCi
0003 CBBC Channel
Name(A-Z)
0005 BBC THREE
FTA
Lock
1 Edit
Group
2 Find 3
PG-+ Page EXIT
Sort
Exit
4 Move
Move
1 In channel list menu, press numeric button "4" , the selected channel will be marked in a symbol " ". Then press "UP" or "DOWN" cursor button to move the selected channel to the position that you want to place.
TV Channel List
All Channel
0 0 0 1 N E W S
0 0 0 2 B B C i
0003 CBBC
0004 BBC 2W
0005 THREE
0006 Wales
2 Press "OK" button, a confirmation window appears.
Select "Yes",press "OK" button to change the channel order.
1 Edit
Group
2 Find
PG-+ Page
3 Sort
EXIT Exit
4 Move
Radio Channel list
1
2
In the Channel menu, select "Radio Channel List", press "OK" button to enter the radio channel list menu.
Press "LEFT" or "RIGHT" cursor button to select channel group. Press "UP" or "DOWN" cursor button to highlight desired channel, and press "OK" button to listen the channel .
Radio Channel List
All Channel
0 7 0 0 R a d i o 1
0 7 0 2 R 5 L i v e
0703 Radio 2
0704 Radio 3
0705 Radio 4
0706 SportsX
0707 6 Music
NOTE:
Basically, the operation of "Radio Channel List" is the same as "TV Channel List", but there is one point different: In "Radio Channel List" mode, there is no video information, so it will always display
Radio's logo in the right side preview window.
1
Edit
Group
2 Find
PG-+
Page
3
EXIT
Sort
Exit
4
Move
Delete All Favorites
Use this menu to delete all favorite channels.
1 In the Channel menu, select "Delete All Favourites" , press "OK" button, a warning window appears.
Channel
TV Channel List
Radio Channel List
2 Select "Yes" and press "OK" button to delete all favorite channels.
Select "No" and press "OK" button to cancel deleting.
Select
No
OK Enter EXIT Exit
Delete All
Use this menu to delete all channels.
1 In the Channel menu, select "Delete All", press "OK" button, you will be asked to input the password (The default password is 0000).
2 Input the correct password , a warning window appears.
Select "Yes", press "OK" button to delete all channels.
Select "No", Press "OK" button to cancel deleting.
Warning: Do you really want to delete all channels ?
Yes No
Channel
TV Channel List
Radio Channel List
Delete All
- - - -
-
Group Rename
Select OK Enter EXIT Exit
Group Rename
Use this menu to change group name.
1
2
In Channel menu, select "Group Rename", press "OK" button to enter group rename menu.
Select desired group, press "OK" button to open the mock keypad.
Input letter and numeric one by one by pressing the cursor button and press "OK" button to confirm. After finishing input, highlight "OK" on mock keypad to confirm, you change group name successfully.
Group Rename
Group 1
Group 2
Group 3
Group 4
Group 5
Group 6
Group 7
Group 8
Select OK Rename EXIT Exit
3 Press "EXIT" button to quit the group rename menu.
Group Rename
Group 1
Group 2
Group 3
Group Rename
Group 1_
Group 4
Group 5
Group 6 g h i j k l m n o p q r
Group 7 s t
1 2 3 4 5 6 7 8 9
!
u v w x y z
`
Group 8
Select OK Rename EXIT Exit
7
English
SYSTEM SET-UP
System setup menu
System setup menu allows us to set OSD Language, TV System, Region and Time, Timer Setting, OSD Setting,
Parental Lock and Standby Mode.
System Setup
1 Press "MENU" button to enter main menu, select "Setup" and press "OK" button to enter system setup menu.
OSD Language
TV System
2 Press "UP" or "DOWN" cursor button to highlight desired menu and press "OK" button to enter the setting menus. Then press
"UP" or "DOWN" cursor button to select desired item, press "LEFT" or "RIGHT" cursor button to change the setting.
Region and Time
Timer Setting
OSD setting
Parental Lock
Standby Mode
3 Press "EXIT" button to exit.
Select OK Enter EXIT Exit
OSD Language
This menu allows you to set OSD Language.
OSD Language: To select your desired OSD language.
OSD Language
OSD Language English
Change EXIT Exit
TV System
This menu allows us to set Display Mode, Aspect Ratio, Video Output and LCN Mode.
Display Mode: NTSC/AUTO/PAL
Aspect Ratio: 4:3PS/4:3LB/16:9/Auto
TV System
Display Mode
Aspect Radio
Video Output
LCN Mode
Video Output:
LCN Mode:
Auto
4:3LB
RGB
Off
RGB/CVBS
Select Change EXIT Exit
If LCN (Logical Channel Number)Select function is activated, you can't change the original number of TV channels by scanning . You can activate/disactivate the LCN function by setting the "LCN Mode " to on/off.
Region and Time
This menu allows you to set the region and time.
Region: This menu is used for changing the region setting.
GMT Usage: This menu is used for open the usage of GMT.
The options are : Off / User Define / By Region
GMT Offset: This menu is valid only when selected "User Define" in GMT Usage menu .
The GMT offset range is "-11:30 ~ +12:00", increasing half hour progressively.
Date:
Time:
"Date" and "Time" menus are valid only when selected "Off" in GMT Usage menu.
Press " OK " then numeric button to change the date and time.
Region and time
Region
GMT Usage
GMT Offset
Date
Time
Time Display
Select
France
By Region
GMT+01:00
2004/03/23
10:56
Off
OK Enter EXIT Exit
Time Display: This menu allow us to control whether the time is displayed on screen or not.
The options are :Off/On.
8 English
SYSTEM SET-UP
Timer Setting
This menu allows us to set the program timer and sleep timer.
Program Timer: This menu is used for setting the program timer you want to change to.
Timer Number:
Timer Mode:
Timer Service:
Wakeup Channel:
Month/Date/Day:
Time:
Auto Record:
Record Duration:
You can set 8 program timer
Off/Once/Daily/Weekly/Monthly
TV Service/Radio Service
You can select a desired channel as the wakeup channel.
Press "LEFT" or "RIGHT" cursor button to select your desired month, date and day.
Press "OK" then press numeric button to input the time.
When it is ON, it is a recording timer.If you
Program Timer
Tuesday xxxx/xx/xx xx:xx change it to OFF, then it will be a viewing timer.
Press "OK" then press numeric button to input the record time.
Auto Record
Record Duration
Off
02:00
When you want to quit program timer, a saving window appears
Sleep Timer: You can set the STB to power off in 10 min,
30min,60min,90min and 120min automatically.
Select
OK
Enter
EXIT
Exit
Program Timer
Tuesday xxxx/xx/xx xx:xx
Timer Number
Timer Mode
Timer Service
Wakeup Channel
Month
Date
Day
Time
1
Once
TV Service
BBC NEWS 24
3
23
Tuesday
10:57
Select
Sleep Timer
Sleep Timer
Remains
OK Enter EXIT Exit
Off
00:00
Change OK Start Timer EXIT Exit
OSD Setting
This menu allows you to set Subtitle Display, OSD Transparency and load default OSD setting.
Subtitle Display: To set the subtitle to Standard / Off/ Teletext.
OSD Transparency: To set the OSD transparency to Off/10%/20%/30%/40%/50%.
Load Default OSD Setting: To clear all OSD setting and reset parameters as default value.
OSD Setting
Subtitle Display
OSD Transparency
Load Default OSD Setting
Off
10%
Select Change EXIT Exit
Parental Lock
This menu allows you to password protect the installation menu and channel, and change the Password.
Parental Lock
1
2
In "System Setup" menu, select "Parental Lock" and press "OK" button , you are asked to input a password(the default password is"0000").
After inputting the correct password by pressing numeric buttons, the parental lock menu appears.
Menu Lock
Channel Lock
New Password
Confirm Password
Menu Lock:
Channel Lock:
New Password:
To lock the installation menu and Edit menu. When you want to enter Auto Scan/ Channel Scan menu, you must input the password. You can set menu lock to on/off.
Select
To lock the channel. You can set channel lock to Off/ Manual/ Age:4- Age:18
To change the password.
Confirm Password: To confirm the new password.
Off
Age:4
----
----
Change
0-9 Input EXIT Exit
Auto Standby
On No command to STB on front panel or Remoter in 3 hours and no timer event,the STB will enter standby mode automatically.
Off The STB can't enter standby mode automatically.
Auto Standby
Auto Standby
On
Select
OK Enter
EXIT Exit
9 English
TOOLS
Tools main menu
1 Press "MENU" button to enter main menu. Select "Tools", press "OK" button to enter tools menu.
2 Press "UP" or "DOWN" cursor button to highlight desired menu and press "OK" button to enter.
3 Press "EXIT" button to exit.
Tools
Receiver Information
Game
Load Factory Default
Software Upgrade
Select
OK
Enter
EXIT
Exit
Receiver Information
This menu can display some parameters of Receiver, Software and Signature information in this STB.
1 In "Tools" menu, select "Receiver Information",press "OK" button to open receiver information window .
Receiver Information
Receiver
Software
Signature
DVB-T xxxx xxx_x_xxxxxx_xx_xxx xxx xx xxxx xx:xx:xx
2 Press "EXIT" button to exit.
EXIT Exit
Game
This menu allows you to play games on this STB.
1
2
In "Tools" menu, select "Game", press "OK" button to enter game menu.
Press "UP" or "DOWN" cursor button to select a desired game, and press "OK" button to enter the game .Highlight "Start" and press "OK" button to start the game.
3 Press "EXIT" button to quit the game.
NOTE:
You can also press "OK" button to pause the game.
Load Factory Default
This menu allows you to reset the STB back to factory settings, clear all existed channels.
1 Enter "Tools" menu, select "Load Factory Default",press "OK" button, you are asked to input password.
2
3
Input a correct password using the numeric buttons(the default password is "0000"), a confirmation window is displayed.
Select "Yes" to return back to factory settings and clear all channels.
Select "No" to cancel back to factory settings.
4 Press "EXIT" button to exit .
Game
Tetris
Snake
Othello
Select
OK
Enter
EXIT
Exit
Tools
Receiver Information
Game software Upgrade
Yes
No
Select
OK Enter EXIT
Exit
Software Upgrade
We offer the functions for user to upgrade software version by air or by storage .
1
2
3
4
Enter "Tools" menu, select "Software Upgrade",press "OK" button, Software Upgrade menu is shown.
Press "Up" or "Down" button to select the desired item and press "OK" button, you are asked to input password.
Input the correct password(the default password is 0000.),Software Upgrade sub- menu is opened.
Press "EXIT" button to exit.
Software Upgrade
Upgrade By Air
Upgrade By Storage
Select
OK
Enter
EXIT
Exit
10 English
Media+
Media+ main menu
1
2
3
Press "MENU" button to enter main menu. Select "Media+ " , press "OK" button to enter Media+ menu.
Press "UP" or "DOWN" cursor button to highlight desired menu and press "OK" button to enter.
Press "EXIT" button to exit.
Media+
Media Player
Record Manage
Removable Disk Information
DVR Configuration
Safely Remove Storage Device
Disk Format
Select
OK
Enter
EXIT
Exit
Media Player
This function allows you to play audio/ video or photo files from
USB device.
1
2
In "Media +" menu, select "Media Player ",press "OK" button to enter Media
Player menu.
Press "UP" or "DOWN" cursor button to select a desired item, and press "OK" button to play the desired files.
3
Press "EXIT" button to exit.
Record Manage
This menu allows you to play the record files
1
2
3
In "Media +" menu, select " Record Manage ",press "OK" button to enter Record
Manage menu.
Press "UP" or "DOWN" cursor button to select a desired item, and press "OK" button to play the desired files.
Press "EXIT" button to exit.
Media Player: USB/Partition1
001 Autorun.inf
002 ALiDvr
I swear.mp3
I swear.mp3
00:03:15 00:04:10
ImgList Music List Image List Setup Sort
Record Manage
SVT1 (DVR)
15:39-15:40(00:01:01) 37M
No. Date Time Name
0001 01/01 01:01-01:02 SVT1
0002 30/08 15:39-15:40 SVT1
0003 10/05 17:41-17:42 France3
0004 01/01 01:00-01:01 France5
1 Lock 2 Delete 3 Rename 4 Information
Removable Disk Information
This menu can display some parameters of Removable Disk.
1 In " Media+ " menu, select "Removable Information",press "OK" button to open removable information window .
2 Press "EXIT" button to exit.
Removable Disk Information
Device
Total
Free
Used
TimeShift
Rec Free
File System xxxxxx x.xx GB x.xx GB x.xx GB x.xxGB
x.xxGB
FAT
EXIT Exit
DVR Configuration
This menu allows us to set the DVR Configuration.
Press "UP" or "DOWN" cursor button to select desired item, press "LEFT" or "RIGHT" cursor button to change the setting.
TimeShift time(min) 10/20/30/40/50/60
The maximum TimeShift time is 1h
Record Type TS/PS
TS: Transportation stream which includes information like teletext,
subtitle, epg etc.
PS: Program stream which will be packeted with the file format
of *.mpg and be also playbacked by PC or other devices.
Standby Mode Off/on
On: When the record is over, the STB will switch to Standby mode.
Off: When the record is over, the STB will not Switch to Standby mode.
11 English
DVR Configuration
Preferred Storage
TimeShift time(min)
Record Type
Standby Mode xxxxxx
20
TS
Off
EXIT Exit
Media+
Safely Remove Storage Device
In " Media+ " menu, select " Safely Remove Storage Device " ,press " OK" button ,
Then a window is displayed.
Highlight "Safely remove USB storage device" ,press " OK" button to confirm.
Please select operation
Safely remove USB storage device
Cancel
Disk Format
This menu allows you to format the disk.
Highlight "File System", press "LEFT"or "RIGHT" cursor button to change the setting.
File System FAT/NTFS
Highlight "Start", press "OK" button, a warning window appears.
Select "Yes", press "OK" button to format.
Select "No", Press "OK" button to cancel.
Disk Format
Device
Capability
File System
Start xxxxxx xxxx MB
FAT
EXIT Exit
WARNING: Format will delete ALL data in this disk,
Continue?
Yes No
12
English
Time Shift / Record
Plugging an external Mass Storage Device on the USB port gives you access to Time Shift/Record a broadcast programme.
Pause a broadcast programme and continue watching it later (Time Shift )
Record a broadcast programme.
When the space available on the Mass Storage Device runs out, recording operation of broadcast will stop.
NOTE:
Please select famous brand USB 2.0 USB HDD or USB stick for Recording and Timeshift, such as SAMSUNG, HITACHI and SONY. Some USB devices maybe can't be supported due to its quality.
Timeshift
Initiate
Time Shift can be done in viewing mode by pressing the "TIME SHIFT " button.
Press "RIGHT " or "LEFT " button to move the cursor to the time you desired to view. Press "OK " button to confirm.
Trickmodes
During the playback, it is possible to perform the following actions :
Press "PAUSE " button to pause the playback
Press "FORWARD " button to fast forward the playback
Press "BACKWARD " button to rewind the playback
Press "SLOW " button to perform slow motion
Stop the Time Shift
9 BBC FOUR
31
03/19 01:36
00:02:37/00:07:12 TimeShift
PS
0%
You will quit timeshift, are you sure ?
Yes No
Press "EXIT/CH+/CH- " button to stop TimeShift, then a confirmation window appears. Select Yes to back to viewing mode displaying the present program. Select No to continue Timeshift.
Record Time Shift
When the Time Shift starts, press the "RECORD " button, a confirmation window appears.
Select Yes to record Time Shift buffering, and then to record present program.
Select No to record present program.
You will quit timeshift, do you want to save all the buffer data to disk?
Yes No
Record
There are 3 different ways to record programmes.
Instant record
In viewing mode, press "RECORD " button to instantaneously start a record on the current channel.
Press "STOP " button to stop recording, then a confirmation window appears.
Select "Stop recording" to stop recording. Select "Continue recording" to continue recording.
If "RECORD " button is pressed again ,the instant record switches to duration mode.
From EPG
Please select operation
Stop recording: TV.18 The Record
Continue recording
Press "RECORD "button on an event to plan a timer on this event.
An icon is then displayed beside the planned event.
Press "RECORD " button to remove the planned record.
Manual scheduling
You can manually set a recording from the Timers menu.
EPG
0001 BBC NEWS 24 31
2004/03/23 10:55
0002 BBCi
0003 CBBC Channel
Now: 10:30-11:00
BBC World News
Next: 11:00-12:00
0004 BBC 2W
BBC News
Wednesday 2008/03/26
01 10:30-11:00 BBC World News
02 11:00-12:00 BBC News
03 12:00-13:00 BBC News
04 16:00-17:00 BBC News
1 Booking List
PG-+ Page
2
OK
Change
Play Booking
3
REC
Detail
Record Booking
13 English
TROUBLESHOOTING
In some region, the digital terrestrial signal may be weak. So you'd better use the antenna in which the booster was built,for watching the weak signal channels.
Problem
Standby light not lit
No signal found
No picture or sound
Scrambled channel message
No response to remote control
Forgotten channel lock code
Forgotten menu lock code
The remote control will not operate your STB
After moving the STB to another room you find you are no longer able to
receive digital reception
Timeshift has not function/
Record has not function
Possible cause
Mains lead unplugged
Mains fuse blown
Aerial is disconnected
Aerial is damaged/misaligned
Out of digital signal area
Scart/AV is not selected on your TV
Channel is scrambled
Receiver off
Handset not aimed correctly
Front panel obstructed
Hand set batteries exhausted
(1) The batteries in your remote
control need replacing
(2) There is an obstruction
blocking the signal path
between the remote control
and the box.
The aerial feed former new point may come through a distribution system which may reduce the digital signal now received by the box.
(1) broken memory device
(2) Poor contact between slot and
memory device.
(3) memory's speed is too low, like
using USB1.0 .
What to do
Check mains lead
Check fuse
Check aerial lead
Check aerial
Check with dealer
Reduce to another channel
Select alternative channel
Plug in and turn on plug
Aim handset at front panel
Check for obstructions
Replace handset batteries
Re-install channels to cancel channel lock
Contact help line
(1) Replace the batteries
(2) Check that there is nothing in
the way of the path between
the remote control and the
receiver
Try a direct feed from the antenna
(1) replace a new memory device.
(2) Pull out and insert again to make
sure good contact
(3) Using USB 2.0 disc when recording
or timeshift.
15 English
SPECIFICATIONS
TUNER & CHANNEL
RF INPUT CONNECTOR x1
(IEC-TYPE, IEC169-2, FEMALE)
RF OUTPUT CONNECTOR x1
(IEC-TYPE, IEC169-2, MALE (LOOPTHROUGH))
FREQUENCY RANGE:
174MHz~230MHz(VHF)
470MHz ~862MHz (UHF)
SIGNAL LEVEL:
-15 ~ -70 dbm
DECODER
AUDIO FORMATS
VIDEO OUTPUT
MPEG Layer I & II, 32 / 44.1 / 48KHz
CVBS, RGB
CONNECTION
MAIN POWER CABLE
TUNER
SCART
SPDIF
DATA PORT
FIXED TYPE
ANTENNA INPUT x1, RF OUTPUT x1
TO TV x1
COAXIAL x1
USB x1
POWER SUPPLY
INPUT VOLTAGE
POWER CONSUMPTION
AC 220-240V ~50/60Hz
MAX. 5W/STANDBY<0.5W
NOTE:
Design and Specifications are subject to change without notice.
1 English
Copyright (c) by Foxit Software Company, 2004 -
For Evaluation Only.
Récepteur numérique terrestre
TDT-130
MANUEL D'UTILISATION
Lire ce manuel avant l'utilisation .
Français
CONTENUS
INFORMATION DE SECURITE
INTRODUCTION
A u sujet du STB
1
1
2
BRANCHEMENT DU SYSTEME
G énéral
Branchement à un TV et un enregistreur video
Branchement à une chaîne HiFi
DÉMARRAGE
Installation Facile
Installation
Recherche automatique
Recherche des Chaînes
Réglage du tuner
3
3
3
4
4
4
4
4
OPERATION
Chang ement de Chaînes
Accéder au Guide électronique de programmes (EPG)
Acc éder aux chaînes favorites
5
5
5
CHAÎNE
Menu liste de chaînes
Liste de chaînes TV
Liste de chaînes de Radio
Éliminer toutes les Favorites
Tout Éliminer
Renommer Groupe
RÉGLAGE DU SYSTÈME
Menu Système de mise en marche
Language OSD
Système TV
R égion et Heure
Réglage de la minuterie
Réglage OSD
Verrouillage Parental
Mise en veille Automatique
OUTILS
Menu principal outils
Information
Récepteur
Jeux
Chargement par Défault
Mise à jour du Software
Media+
Me nu Principal Media+
Media Player
Gestion d'enregistrement
Information disque amovible
Configuration DVR
Retirer le périphérique de stockage
Format Disque
Timeshift/ Enregistrement
Timeshift
Enregistrer
POSSIBLES PROBLEMES
10
10
10
10
10
9
9
9
9
8
8
8
8
11
11
11
11
11
12
12
6
7
7
6-7
7
7
13
13
15
CARACTÉRISTIQUES
16
INTRODUCTION
Au sujet du STB
Panneau Frontal
Capteur IR Indicateur de puissance
Port USB
Panneau Arrière
Entrée RF pour antenne extérieure
Péritel TV pour connexion
à votre TV
Audio Numérique Coaxial
A limentation AC
RF Loop à travers d'un appareil externe
1 Français
BRANCHEMENT DU SYSTÈME
Général
Vous pouvez connecter au récepteur différents types de matériel de télévision et leurs accessoires .
Dans ce manuel, vous verrez quelques-unes des façons les plus courantes de connecter votre équipement.
Branchement à une TV / enregistreur video avec SC ART
Câble Peritel
Antenn e câble RF
TV Câble
Branchement à une HiFi
C âble Coaxial
3
Français
3
DEMARRAGE
Facile Installation
Si vous utilisez le STB pour la première fois, le menu "Installation facile" apparaîtra .
Easy Install
Easy Install
Avec sur le curseur "GAUCHE" ou "DROITE" pour ajuster la Region & Language.
Region
Choisisser "Rechercher", appuyez sur "OK" pour démarrer la recherche de canaux.
OSD Language
Search
Spain
English
Select OK Enter EXIT Exit
Installation
1
Appuyer sur la touche "MENU" pour introduire le menu principal.
Installation
2
Appuyer "GAUCHE"ou "DROITE" pour sélectionner "Installation", sur "OK" pour accéder au menu d'installation.
Auto Scan
Channel Scan
Power Control
3 Appuyer sur la touche "EXIT" pour sortir.
Select OK Enter
Recherche automatique
1
2
Appuyer sur " HAUT" ou "BAS" pour sélectionner le "Auto Scan", sur "OK" pour entrer dans le menu Auto Scan.
Appuyer sur la touche du curseur "GAUCHE" ou "DROITE" pour faire la
recherche et marquer "Recherche", puis sur "OK" pour initier la recherche.
EXIT Exit
Auto Scan
TV Channel List
2 BBCi
3 CBBC Channel
4 BBC 2W
5 BBC THREE
6 BBC ONE Wales
Radio Channel List
1 BBC Radio Wales
2 BBC Radio Cymru
UHF: 470.0-862.0 MHz Ch No: GI:
Frequency: 490.00 Mhz Modulation: FFT:
24%
EXIT Exit
Recherche Chaîne
1
2
Appuyer sur "HAUT" ou "BAS" puis marquer "Recherche chaîne" et appuyer sur "OK" pour introduire le menu de Recherche de Chaînes.
Appuyer sur curseur "GAUCHE" ou "DROIT" pour sélectionner
Scan mode, Scan Band et num. de la chaîne. et marquer "Recherche", appuyer sur la chaîne pour commencer la recherche de la chaîne.
Mode de recherche:
Par chaîne
Par fréquence.Choisisser
Channel Scan
Scan Mode
Scan band
Ch No.
Frequency
Band Width
Network Search
By Channel
UHF
22(482.000MHz)
482.000
8 MHz
Off
Search
Signal Intensity
Signal Quality
Select OK Enter EXIT
94%
97%
Exit
Réglage Tuner
Appuyer sur "UP" ou "DOWN " pour sélectionner "Tuner Power",
appuyer sur "OK" et option "Tuner Power" pour le remarquer.
Tuner Power: On/Off
RF Loop-through: On/Off
4
Français
Power Control
Tuner Power Off
RF Loop-through Off
Change EXIT Exit
OPERATION
Changer les chaînes
Il ya quatre façons de sélectionner les chaînes : pas à pas de la liste des chaînes, la sélection par numéro, à partir de la liste des chaînes à l'écran, et l'aide du guide électronique des programmes (EPG).
1
Réglage à travers de la liste de chaînes:
Pour vous déplacer dans la liste des chaînes, appuyez sur la flèche vers le haut ou flèche
vers le bas de la télécommande.
2
3
Select ionner par numéro:
Introduire le numéro de la chaîne directement en appuyant sur les touches numériques,
et appuyer sur la touche "OK" pour sélectionner la chaîne désirée.
Selectionner sur la liste de l'écran:
Vous pouvez également sélectionner la chaîne désirée depuis la liste sur l'écran. Celle-cie se déploie du menu principal de l'STB. Voir "Liste de Chaîne" dans ce manuel pour détail.
4 Select ionner par EPG:
Vous pouvez également sélectionner la chaîne à partir du guide de programmes électro-
nique (EPG). Celui-ci apparaît en utilisant le menu principal du STB. Voir «Accès au guide
électronique des programmes (EPG)" dans ce manuel pour les détails de fonctionnement.
Accès au Guide Electronique de Programmes (EPG)
Accès à l'EPG de tous les canaux:
1
2
3
4
Appuyer sur la touche "EPG" pour entrer dans le menu EPG.
Appuyer sur la touche numérique "2" pour changer entre liste de chaînes, calendrier des événements du canal sélectionné et actuel/prochain.
Dans le calendrier de l'événement, "OK" pour réserver l'événement sélectionné, sur la touche numérique "3" pour ouvrir le détail du choix.
EPG
1
0001 BBC NEWS 24 31 2004/03/23 10:55
0002 BBCi
Now: 10:30-11:00
BBC World News
0003 CBBC Channel
0004 BBC 2W
Next: 11:00-12:00
BBC News
Wednesday 2008/03/26
01 10:30-11:00 BBC World News
02 11:00-12:00 BBC News
03 12:00-13:00 BBC News
04 16:00-17:00 BBC News
Booking List
PG-+ Page
2
OK
Change
Play Booking
3
REC
Detail
Record Booking
Appuyer sur la touche numérique "1" pour ouvrir la liste en réserve.
Acceder aux chaînes favorites
1
2
3
Appuyer sur la touche "FAV" pour entrer dans le menu groupe de favoris.
Utiliser le curseur "HAUT" ou "BAS" pour sélectionner le groupe de favoris.
Appuyer sur la touche "OK" pour introduire la liste de chaînes, et appuyer sur le curseur "HAUT" ou "BAS" pour sélectionner la chaîne favorite.
Favorite
Group 1
Group 2
5
Français
CHAÎNES
Menu liste de Chaînes
1 Appuyer sur la touche "MENU" pour introduire le menu principal, sélectionner sur la "Chaîne" et appuyer sur "OK" to enter Channel menu.
2
3
Appuyer depuis le curseur "HAUT" ou "BAS" pour marquer l'option désirée et sur "OK" pour le menu de réglage .
NOTE: Vous pouvez également appuyer "OK" pour entrer dans la liste de chaînes en mode de reproduction normal.
Appuyer sur "EXIT" pour sortir.
Channel
TV Channel List
Radio Channel List
Delete All Favorites
Delete All
Group Rename
Select OK Enter EXIT Exit
Liste de Chaînes TV
1
2
Dans le menu liste de Chaînes, sélectionner "TV Channel List", et sur "OK" pour la liste de chaîne
Appuyez sur "GAUCHE" ou "DROITE" pour sélectionner le groupe de chaîne. Et appuyez sur
"HAUT" OU "BAS" du curseur pour prévisualiser la chaîne de télévision souhaitée. Appuyer sur le bouton "OK" pour afficher la chaîne sélectionnée en plein écran.
TV Channel List
All Channel
0 0 0 1 N E W S 2 4
0 0 0 2 B B C i
0 0 0 3 C B B C
0 0 0 4 B B C 2 W
0 0 0 5 T H R E E
0 0 0 6 Wa l e s
1 Edit
Group
2
PG-+
Find
Page
3 Sort
EXIT Exit
4 Move
Edit er
U tiliser ce menu pour favoriser, verrouiller, supprimer et renommer une liste de chaîne.
Dans le menu liste de chaîne, pressioner la touche numérique "1" pour le menu éditer.
Marquer une chaîne et appuyer sur "OK" pour la sélectioner. Ou sur la touche "0" pour sélectionner toutes les chaînes all channels.
Appuyer sur la touche "EXIT" pour sortir du menu d'édition.
Favor iser:
Dans le menu "Edit Channel", appuyer sur la touche numérique "1", ensuite sur
"HAUT" ou "BAS" pour sélectionner un groupe désiré, et sur la touche "OK", une fenêtre de confirmation apparaîtra.
TV Channel List
A l l C h a n n e l
0 0 0 1 2 4
0 0 0 2 B B C i
0003 CBBC
0004 BBC 2W
0005 THREE
0006 Wales
OK
4
Select
Delete
0
5
All
Rename
1 Favor
Group
2
PG-+
Lock
Page
3 Skip
EXIT Exit
TV Channel List
Group 1
Group 2
0002 BBCi
S électionner "Oui" et appuyer sur la touche "OK", la chaîne désirée sera ajoutée au groupe.
Verrouiller:
Dans le menu "Editer Chaîne", appuyer sur la touche "2", une fenêtre de confir- mation apparaîtra. Sélectionner "Oui" et la touche "OK" la chaîne sera verrouillée.
Répétez les étapes ci-dessus pour débloquer les canaux verrouillés.
S auter:
Dans le menu "Editer Chaîne", appuyer sur la touche "3", une fenêtre de confirmation apparaîtra. Sélectionner "Oui" et la touche "OK", la chaîne sera sautée en changeant la chaîne à plein écran. Répeter pour annuler les sauts de chaînes.
Group 7
Group 8
OK
4
Select
Delete
0
5
All
Rename
1 Favor
Group
2
PG-+
Lock
Page
3 Skip
EXIT Exit
Switch lock channel. Are you sure?
Yes No
Switch skip channel. Are you sure?
Yes No
Effacer: Delete Channel. Are you sure?
Yes No
Dans le menu "Editer Chaîne", appyer sur la touche "4", une fenêtre de confirmation apparaitra. Sélectionner "Oui", appuyer sur "OK" pour effacer la chaîne sélectionnée de la liste de chaîne.
Ren ommer:
Dans le menu "Editer Chaîne", appuyer sur la touche "5" pour ouvrir le clavier. Introduire lettres et numer os un à un en appuyant sur le curseur et appuyer sur "OK" pour confirmer. une fois terminé aller sur "OK" du clavier pour confirmer, vous avez correctement changé le nom.
Trouver
1
2
3
Dans le menu, appuyer sur la touche "2" pour entrer dans le menu Trouver.
Appuyer sur la touche pour marquer la lettre ou numéro désiré et sur la touche "OK" in troduire un à un. Une fois introduit les caractères, la liste de chaîne cherchera la chaîne en accord à votre sélection et affichera la chaîne trouvée.
Appuyer sur la touche "SORTIR" pour sortir du menu "Trouver".
TV Channel List
A l l C h a n n e l
0 0 0 1 N E W S 2 4
0 0 0 2 B B C i
0003 CBBC
0004 BBC 2W
0005 THREE
0006 Wales
Find
A B C D E F G
H I J K L M N
O P Q R S T U
V W X Y Z 1 2
3 4 5 6 7 8 9
0
( sp DEL OK
1 Edit
Group
2 Find
Page
3 Sort
EXIT Exit
4 Move
6
Français
CHAîNE
Liste de Chaînes TV (Continuée)
Organiser TV Channel List
All Channel
2
Déplacer
1
Dans le menu liste e chaîne, appuyer sur "4", la chaîne sélectionnée sera marquée avec le la chaîne sélectionnée à la position à laquelle vous désirez la placer.
0002 BBCi
Appuyez sur la touche "UP" ou "DOWN" du curseur pour sélectionner votre mode de tri souhaité et appuyez sur "OK" pour confirmer.
Default:
N
N om (A-Z): om (Z-A):
FTA:
Lock:
Trier par résultat scanné.
Trier par ordre Alphabétique.
Trier par ordre Alphabétique.
Tamisage sur toutes les chaînes libres.
Accumule les chaînes verrouillées et la liste dans la dernière liste des chaînes TV.
0003 CBBC Channel
Name(A-Z)
0005 BBC THREE
FTA
Lock
1 Edit
Group
2 Find 3
PG-+ Page EXIT
Sort
Exit
TV Channel List
All Channel
0 0 0 1 N E W S
0 0 0 2 B B C i
0003 CBBC
0004 BBC 2W
0005 THREE
0006 Wales
4 Move
2
Appuyer sur la touche "OK", une fenêtre de confirmation apparaîtra.
S
électionner "Oui", appuyer sur la touche "OK" pour changer l'ordre des chaînes.
Edit
Group
2 Find
PG-+ Page
3 Sort
EXIT Exit
4 Move
Liste de Chaînes Radio
1
Dans le menu Chaîne, sélectionner "Liste Chaîne de Radio", appuyer sur "OK" pour choisir la chaîne Radio dans le menu liste de chaîne.
2
Depuis le curseur "GAUCHE" ou "DROITE" pour sélectionner le groupe. Avec le curseur EN
"HAUT" ou "BAS" et marquer la chaîne désirée, sur la touche "OK" pour écouter la chaîne .
NOTE:
Fondamentalement l'opération "Liste ChaÌne Radio" est la même que "Liste Chaîne TV", mais il y a une différence: Dans le mode "Liste Chaîne Radio", il n'y a pas d'information vidéo, le logo Radio apparaîtra toujours affiché dans la fenêtre de prévisualisation à droite
Radio Channel List
All Channel
0 7 0 0 R a d i o 1
0 7 0 2 R 5 L i v e
0703 Radio 2
0704 Radio 3
0705 Radio 4
0706 SportsX
0707 6 Music
Edit
Group
2 Find
PG-+
Page
3
EXIT
Sort
Exit
4
Move
Effacer toutes les favorites
U tiliser ce menu pour effacer les chaînes favorites.
1
Dans le menu Chaîne, sélectionner "Effacer Tous Favoris" ,sur "OK", une fenêtre d'attention apparaîtra.
2 S
électionner "Oui" et appuyer sur "OK" pour effacer les chaînes favorites.
S électionner "Non" et appuyer sur "OK" pour annuler l'éllimination.
Channel
TV Channel List
Radio Channel List
Select
Tout effacer
U tiliser ce menu Pour éliminer toutes les chaînes.
1
Dans le menu Chaîne, sélectionner "Delete All", sur "OK", pour introduire le môt de passe (Le môt de passe par défault est 0000).
2 Introduire le môt de passe correct , Une fenêtre d'avertissement apparaîtra.
S
électionner "Oui", sur "OK" pour toutes les éliminer.
S électionner "Non", sur "OK" pour annuler l'élimination.
WARNING: Are you sure to delete ALL channels ?
Yes No
No
OK Enter EXIT Exit
Channel
TV Channel List
Radio Channel List
Delete All
- - - -
-
Group Rename
Select OK Enter EXIT Exit
Renommer Groupe
U tiliser ce menu pour changer le nom du groupe.
1
Dans le menu Chaîne, sélectionner "Renommer Groupe", et "OK"pour introduire le menu de renommer groupe.
Group Rename
2 S
I
électionner le groupe désiré, sur "OK" pour ouvrir le clavier.
ntroduire lettre et numéro un à un en pressionnant sur le curseur. et appuyer "OK" pour confirmer. Une fois réalisé, marquer "OK" sur le clavier pour confirmer, et vous aurez changé le nom du groupe.
Group 1
Group 2
Group 3
Group 4
Group 5
Group 6
Group 7
Group 8
Select OK Rename EXIT Exit
3 Appuyer sur "EXIT" pour sortir du menu de renommer groupe.
Group Rename
Group 1
Group 2
Group 3
Group Rename
Group 1_
Group 4
Group 5
Group 6 g h i j k l m n o p q r
Group 7 s t
1 2 3 4 5 6 7 8 9
!
u v w x y z
`
Group 8
Select OK Rename EXIT Exit
7
Français
SYSTÈME DE RÉGLAGE
Menu de réglage du système
Le menu Configuration du système permet de régler le Language OSD, TV System, Région et Heure, Timer Setting,
OSD Settings, Parental Lock et Mode Standby.
System Setup
1
Appuyer sur la touche "MENU" pour le menu principal, sélectionner "Setup" et appuyer sur "OK" pour entrer dans le menu de configuration du système.
OSD Language
TV System
2 Appuyer sur le curseur "HAUT" ou "BAS" pour marquer le menu désiré et appuyer s ur "OK" pour introduire les menu de configuration. Ensuite avec le curseur
" HAUT" ou "BAS" pour sélectionner l'option désirée, appuyer sur la touche du curseur "GAUCHE" ou "DROIT" pour modifier les paramètres.
Region and Time
Timer Setting
OSD setting
Parental Lock
Standby Mode
3
Appuyer sur la touche "EXIT" pour sortir.
Select OK Enter EXIT Exit
Language OSD
Ce menu vous permet d'ajuster le Language de l'OSD.
OSD Language:
Pour sélectionner votre Language OSD désiré.
OSD Language
OSD Language English
Change EXIT Exit
Système TV
Ce menu permet d'ajuster le Mode Display, Aspect Ratio, Video Output, et LCN Mode.
Display Mode: NTSC/AUTO/PAL
Aspect Ratio: 4:3PS/4:3LB/16:9/Auto
TV System
Display Mode
Aspect Radio
Video Output
LCN Mode
Auto
4:3LB
RGB
Off
Video Output: RGB/CVBS
Select Change EXIT Exit
LCN Mode: Si la sélection de la fonction LCN (Logical Channel Number)est activée, vous ne pouvez pas changer le numéro original des chaînes TV par recherche . Vous pouvez activer/désactiver la fonction du réglage LCN dans le "LCN Mode " avec on/off.
Région et Heure
Ce menu vous permet d'ajuster la région et l'heure.
Region and time
Region:
Ce menu est utilisé pour changer le réglage de la région.
Region
GMT Usage
GMT Usage: Ce menu est utilisé pour ouvrir l'utilisation de GMT.
Les options sont : Off / User Define / By Region
GMT Offset
Date
Time
GMT Offset:
Ce menu n'est valable que dans le menu "User Define" du menu GMT Usage . Time Display
Le décalage GMT est "-11:30 ~ +12:00", augmentant par demi heure progressive ment.
Date:
Time:
Les menus"Date" et "Heure" sont valables uniquement lorsque l'option
"Off" dans le menu Utilisation GMT est sélectionnée.
Appuyer sur " OK " puis la touche numérique pour changer la date et heure.
Select
France
By Region
GMT+01:00
2004/03/23
10:56
Off
OK Enter EXIT Exit
Time Display: Ce menu permet de contrôler si l'heure est affichée sur l'écran ou non. Les options sont: Off / On.
Les options sont: Off/On.
8
Français
RÉGLAGE DU SYSTÈME
Timer Setting
Ce menu permet de régler la minuterie du programme et mise en veille.
Program Timer: Ce menu est utilisé pour régler la minuterie que vous voulez changer.
Timer Number:
Timer Mode:
Timer Service:
Chaîne de réveil:
Mo is/Date/Jour:
Heure:
Auto Record:
Durée Enregistrée:
Vous pouvez ajuster la minuterie de 8 programmes.
Off/ Une fois/par Jour/par semaine/Mensuel
Service TV/Service Radio.
Vous pouvez sélectionner une chaîne désirée comme chaîne de réveil.
Appuyer sur le curseur "GAUCHE" ou "DROIT" pour sélectionner votre mois, date et jour désiré.
Appuyer sur "OK" puis la touche numérique pour l'heure.
Off/On
Program Timer
Tuesday xxxx/xx/xx xx:xx
Appuyer "OK" puis la touche numérique pour introduire l'heure d'enregistrement.
Auto Record
Record Duration
Off
02:00
Lorsque vous voulez sortir du programmateur, une fenêtre de confirmation apparaît.
Sleep Timer: Vous pouvez ajuster le STB pour s'éteindre en 10 min,
30min,60min,90min et 120min automatiquement.
Select
OK
Enter
EXIT
Exit
Program Timer
Tuesday xxxx/xx/xx xx:xx
Timer Number
Timer Mode
Timer Service
Wakeup Channel
Month
Date
Day
Time
1
Once
TV Service
BBC NEWS 24
3
23
Tuesday
10:57
Select OK Enter EXIT Exit
Sleep Timer
Sleep Timer
Remains
Off
00:00
Change OK Start Timer EXIT Exit
Réglage de l'OSD
Ce menu vous permet de régler l'affichage sous-titres, la Transparence OSD par défaut et réglage OSD.
Affichage sous-titre: Pour définir le sous-titre Normal / Off / Télétexte.
OSD Setting
Subtitle Display
OSD Transparency
OSD Transparenc e: Pour ajuster la transparance de l'OSD à Off/10%/20%/30%/40%/50%.R
Load Default OSD Setting
Off
10%
Réglage OSD par défaut: Pour effacer les réglages OSD aux valeurs par défaut.
Select Change EXIT Exit
Verrouillage Parental
Ce menu vous permet de protéger le menu installation et chaîne avec un môt de passe et de pouvoir le changer.
1
Dans le menu "System Setup", selectionner "Parental Lock" et appuyer "OK", on vous demandera d'introduire le môt de passe (le môt de passe par défaut est"0000").
Parental Lock
Menu Lock
Channel Lock
Off
Age:4
2
Une fois introduit le môt de passe correct avec les touches numériques, le menu de verrouillage parental apparaîtra.
New Password
Confirm Password
----
----
Menu ge: Pour verrouiller le menu Edition. Lorsque vous voulez introduire le
menu Recherche Auto/ Recherche Chaîne, vous devez introduire le
Select
Change
0-9 Input EXIT Exit
N
môt de passe. Vous pouvez ajuster le menu de verrouillage sur on/off.
Pour verrouiller la chaîne. Vous pouvez ajuster le verrouillage de chaîne a Off/ Manuel/ Age:4- Age:18
Pour changer le môt de passe.
Confirm er Môt de passe: Pour confirmer le nouveau môt de passe.
Mode Standby
On
Pas d'ordre au décodeur sur le panneau avant pour une durée de 3 heures et aucun évènement programmé, le STB se met en veille automatiquement .
Off
Le STB ne peut pas entrer en mode veille automatiquement.
Auto Standby
Auto Standby
On
Select
OK Enter
EXIT Exit
9 Français
OUTILS
Menu del principaux outils
1
Appuyer sur la touche "MENU" pour entrer dans le menu principal. Sélectionner
"Tools", appuyer sur la touche "OK" pour introduire le menu outils.
2
Appuyer sur la touche du curseur "UP" ou "DOWN" pour marquer le menu désiré et appuyer sur la touche "OK" pour l'introduire.
3 Appuyer sur la touche "EXIT" pour sortir.
Tools
Receiver Information
Game
Load Factory Default
Software Upgrade
Select
OK
Enter
EXIT
Exit
Information Récepteur
Ce menu peut afficher des paramètres du Récepteur, Software et information de Signature de cet STB.
1
Dans le menu "Outils", sélectionner "Information Récepteur", appuyer sur "OK" pour ouvrir la fenêtre d'information du récepteur.
Receiver Information
Receiver
Software
Signature
DVB-T xxxx xxx_x_xxxxxx_xx_xxx xxx xx xxxx xx:xx:xx
2 Appuyer sur la touche "EXIT" pour sortir.
EXIT Exit
Jeux
Ce menu vous permet de jouer à des jeux inclus dans cet STB.
1
Dans menu "Outils", sélectionnez "Game", appuyez sur "OK" pour entrer dans le jeu.
2
3
Appuyer sur la touche curseur "UP" ou "DOWN" pour sélectionner le jeu désiré, et "OK" pour introduire le jeu . Marquer "Start" et appuyer sur la touche "OK" pour commencer.
Appuyer sur la touche "EXIT" pour avandonner le jeu.
NOTE:
Vous pouvez aussi appuyer "OK" pour faire une pause.
Game
Tetris
Snake
Othello
Select
OK
Enter
EXIT
Exit
Charger aux défauts d'usine
Ce menu permet de retourner aux réglages d'usine du STB, Effacer les chaînes existantes.
1 Entre dans le menu "Outils", sélectionner "Charger Defaut d'Usine", et sur "OK",
On vous demandera d'introduire le môt de passe.
2
3
I ntroduire un môt de passe correct en utilisant les touches numériques, le môt de passe par défaut est "0000". Une fenêtre de confirmation apparaîtra.
S électionner "Oui" pour retourner aux réglages d'usine et effacer toutes les chaînes.
S
électionner "Non" pour annuler le retour aux réglages usine.
4 Appuyer sur "EXIT" pour sortir .
Tools
Receiver Information
Game software Upgrade
Yes
No
Select
OK Enter EXIT
Exit
Télédécharger Logiciel
Nous fournissons les fonctions pour faire la mise à jour du logiciel par air ou par stockage.
1
Entrer dans le menu "Outils", sélectionner "Software Upgrade", sur la touche "OK", le menu de mise à jour du logiciel sera montré.
Appuyer sur la touche "Haut" ou "Bas" pour sélectionner l'option désirée et sur la touche "OK" demandée pour introduire le môt de passe.
3
4
In troduire le môt de passe correct (le môt de passe par défaut est 0000.), le sous-menu de mise à jour du logiciel sera ouvert.
Appuyer sur la touche "EXIT" pour sortir.
Software Upgrade
Upgrade By Air
Upgrade By Storage
Select
OK
Enter
EXIT
Exit
10 Français
Media+
Menu principal Media+
1
2
3
Appuyer sur la touche "MENU" pour introduire le menu principal. Sélectionner
"Media+" et appuyer sur la touche "OK" pour introduire le menu Media+.
Appuyer sur se curseur "HAUT" ou "BAS" pour marquer le menu de l'option désirée, appuyer ensuite sur la touche "OK" pour entrer.
Appuyer sur la touche "EXIT" pour sortir.
Media+
Media Player
Record Manage
Removable Disk Information
DVR Configuration
Safely Remove Storage Device
Disk Format
Select
OK
Enter
EXIT
Exit
Media Player
Cette fonction vous permet de reproduire audio/ video ou fichiers photos
à partir du périférique USB.
1
2
3
Dans le menu "Media +" menu, sélectionner "Media Player ", appuyer sur "OK" pour
Introduire le Menu Media Player.
Appuyer sur la touche du curseur "HAUT" ou "BAS" pour sélectionner l'option désirée, et appuyer sur "OK" pour reproduire les fichiers désirés.
Appuyer sur la touche "EXIT" pour sortir.
Media Player: USB/Partition1
001 Autorun.inf
002 ALiDvr
I swear.mp3
I swear.mp3
00:03:15 00:04:10
ImgList Music List Image List Setup Sort
Gérer les enregistrement
Ce menu permet de reproduire les fichiers enregistrés
1
2
3
Dans le menu "Media +", sélectionner "Administration d'enregistrement", appuyer sur "OK" pour introduire le menu d'Administiration d'enregistrement.
Appuyer sur le boutton de la touche "HAUT" ou "BAS" sélectionner l'option désirée et appuyer sur "OK" pour reproduire les fichiers désirés.
Appuyer sur la touche "SORTIR" pour sortir.
Record Manage
SVT1 (DVR)
15:39-15:40(00:01:01) 37M
No. Date Time Name
0001 01/01 01:01-01:02 SVT1
0002 30/08 15:39-15:40 SVT1
0003 10/05 17:41-17:42 France3
0004 01/01 01:00-01:01 France5
1 Lock 2 Delete 3 Rename 4 Information
Information Disque amovible
Ce menu peut montrer des paramètres de Disque amovibles.
1
Dans le menu " Media+ ", sélectionner "Information Amovible", appuyer sur "OK" pour ouvrir la fenêtre d'information amovible.
2 Appuyer sur la touche "EXIT" pour sortir.
Removable Disk Information
Device
Total
Free
Used
TimeShift
Rec Free
File System xxxxxx x.xx GB x.xx GB x.xx GB x.xxGB
x.xxGB
FAT
EXIT Exit
Configuration DVR
Ce menu nous permet d'ajuster la configuration du DVR.
Appuyer sur la touche du curseur "HAUT" ou "BAS" pour sélectionner, et
"GAUCHE" ou "DROITE" pour changer le réglage.
T emps TimeShift (min) 10/20/30/40/50/60
Le temps de TimeShift maximum est 1h
Type d'enregistrement TS/PS
TS: Flux de Transport qui inclus l'information tel que télétexte,
s ous-tittre, EPG etc.
DVR Configuration
Preferred Storage
TimeShift time(min)
Record Type
Standby Mode
PS: Flux de Programmes qui seront emballés avec le format de fichier de *.mpg et être également lu par ordinateur ou d'autres appareils.
Standby Mode
Off/on
EXIT
On:
Lorsque l'enregistrement est terminé, le STB se met en mode veille.
Off: Lorsque l'enregistrement est terminé, le STB ne s'allume pas en mode de veille
Exit xxxxxx
20
TS
Off
11 Français
Media+
Retirer le périphérique de stockage
Dans le menu " Media+ ", sélectionner "Retirer le Périphérique de Stockage ", appuyer " OK",
Une fenêtre sera déployée.
Marquer "Retirer le périphérique de stockage USB", appuyer sur "OK" pour confirmer.
Please select operation
Safely remove USB storage device
Cancel
Format Disque
Ce menu vous permet de formater le disque.
Marquer "File System", appuyer "GAUCHE" ou "DROITE" du curseur pour changer les réglages.
Disk Format
Device
Capability
File System
Syst
éme Fichier FAT/NTFS
Marquer "Start", appuyer sur la touche "OK", une fenêtre d'avertissement apparaîtra
S électionner "Non", Appuyer sur la touche "OK" pour annuler.
EXIT Exit
Start xxxxxx xxxx MB
FAT
WARNING: Format will delete ALL data in this disk,
Continue?
Yes No
12
Français
Time Shift / Enregistrement
Le branchement d'un périphérique de stockage de masse externe sur le port USB, vous permet d'accéder à
Time Shift / enregistrer un programme diffusé.
Mettre en pause un programme de diffusion et de continuer à le regarder plus tard (Time Shift)
Enregistrer une émission.
Lorsque l'espace disponible sur le périphérique de stockage de masse est vide, l'opération d'enregistrement s'arrête.
NOTE:
Veuillez choisir une bonne marque USB 2.0 disque dur USB ou une clé USB pour enregistrer et TimeShift comme SAMSUNG, HITACHI and SONY. Certains USB peuvent ne pas être pris en charge dû à leur qualité.
Timeshift
Initiate
T ime Shift peut être fait en mode de visualisation en appuyant sur la touche "TIME SHIFT.
Appuyer sur la touche "DROITE " ou "GAUCHE" bouger le curseur jusqu'au temps désiré pour voir. Appuyer sur "OK "pour confirmer.
Trickmodes
Dur ant le playback, il est possible d'effectuer les actions suivantes :
Appuyer sur "PAUSE " pour pauser le playback
Appuyer sur "FORWARD " pour passer rapidement le playback
Appuyer sur "BACKWARD " pour rebobinner le playback
Appuyer sur "SLOW " pour effectuer un mouvement lent
Stop per le Time Shift
9 BBC FOUR
31
03/19 01:36
00:02:37/00:07:12 TimeShift
You will quit timeshift, are you sure ?
Yes No
PS
0%
Appuyer sur "EXIT/CH+/CH- " pour arrêter le TimeShift, une fenêtre de confirmation apparaîtra. Sélectionner Oui pour retourner au mode de vue montrant le programme actuel. Sélectionner Non pour continuer le Timeshift.
Record Time Shift
Lorsque Time Shift commence, appuyer sur "RECORD", une fenêtre de confirmation apparaît.
S
électionner Oui pour enregistrer en mémoire tampon Time Shift, et enregistrer le programme actuel.
S
électionner Non pour enregistrer le programme actuel.
You will quit timeshift, do you want to save all the buffer data to disk?
Yes No
Enregistrement
Il y a 3 différentes façons d'enregistrer les programmes.
Enregistrement instantanné
En mode vue, appuyer "RECORD" pour commencer instantanément un enregistrement sur la chaîne actuelle.
Appuyer sur "STOP " pour arrêter l'enregistrement, une fenêtre de confirmation apparaît.
S
électionner "Stop recording" pour arrêter l'enregistrement. Et "Continue recording" pour continuer l'enregistrement.
If "RECORD" est appuyée à nouveau, l'enregistrement change à mode de durée.
Please select operation
Depuis l'EPG
Stop recording: TV.18 The Record
Continue recording
Appuyer sur "RECORD" sur un évènement pour programmer un évènement
Un icon est alors montré à côté de l'évènement planifié.
Appuyer sur "RECORD" pour enlever l'enregistrement planifié.
EPG
0001 BBC NEWS 24
0002 BBCi
Planification Manuelle
31
2004/03/23 10:55
Now: 10:30-11:00
0003 CBBC Channel
BBC World News
Next: 11:00-12:00
0004 BBC 2W
BBC News
Wednesday 2008/03/26
Vous pouvez ajuster un enregistrement depuis le menu Timers.
01 10:30-11:00 BBC World News
02 11:00-12:00 BBC News
03 12:00-13:00 BBC News
04 16:00-17:00 BBC News
1 Booking List
PG-+ Page
2
OK
Change
Play Booking
3
REC
Detail
Record Booking
13 Français
o
POSSIBLES PROBLÈMES
Dans certaines régions, le signal terrestre numérique peut être faible. Vous devriez mieux utiliser l'antenne dans laquelle le cerveau moteur a été construit, pour regarder les chaînes à signaux faibles.
Probl ème
la veilleuse ne s'allume pas
Pas de signal trouvé
Pas d'image ou son
Message chaine cryptée
N e répond pas à la télécommande
Code de verrouillage oublié
Code de menu oublié
La télécommande ne fait pas marcher votre STB
A près avoir déplacé le STB dans une autre pièce vous trouvez que vous ne receve z plus le signal.
Timeshift sans fonction/
Enregistrement sans fonction
Possible cause
Câble d'alimentation débranché
Fusible secteur soufflé
A ntenne déconnectée
A ntenne endommagée/désalignée
Hors zone de signal numérique
Scart/AV n'est pas sélectionné sur TV
Cha îne est cryptée
Que faire
Vérifier l'alimentation
Vérifier le fusible
Vérifier le câble d'antenne
Vérifier l'antenne
Vérifier avec votre distributeur
R éduire à une autre chaîne
S
électionner une chaîne alternative
R écepteur étteind
Télécommande mal dirigée
Panneau avant obstrué
Piles trop faibles
Brancher et allumer
Diriger la télécommande face au panneau
Vérifier ce qui gène
Re mplacer les piles de la télécommande
Re-install er les chaînes pour annuler verrouillage chaîne
Contact er la ligne d'aide
(1) Les piles de la télécommande
n'ont pas été remplacées
(2) Une obstruction bloque le chemin
du signal entre la télécommande
et votre récepteur.
Le nouveau point d'alimentation de l'antenne peut venir d'un système de distribution qui peut réduire le signal numérique non reçu par le récepteur.
(1) Re mplacer les piles
(2) Vérifier qu'il n'y a rien de part la la ligne entre la télécommande et le récepteur
Essayer le courant depuis l'antenne
(1) dispositif de mémoire
(2)
Mauvais contact entre la fente et
le dispositif de mémoire.
(3) vitesse de la mémoire trop faible,
comme de l'utilisation d'USB1.0 .
(1) re mplacer par un nouveau stockage.
(2) Retirer et insérez à nouveau pour s'assurer un bon contact
(3) U tilisez un USB 2.0 sorsque vous enregistrer ou timeshift.
14 Français
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project