Monogram Advantium ZSC2200, PSB9240SFSS User manual

Monogram Advantium ZSC2200, PSB9240SFSS User manual
solid floor
Required
cutout location
36-3/4"
minimum
from floor
29-3/4"
PSB9240SF
Suitable
bracing
™
to support
runners
3/8" Plywood
Supported by
2 x 4 or 1 x 2
Runners, all
Four Sides.
(Must Support
150 lbs.)
cabinet
21-5/8"
®
width
GE Profile Series
Advantium
240V
30
in.
Wall
Oven
over centerline
Advantium Wall Oven Dimensions (in inches)and
of cabinet
A=Allow 1" overlap of oven over bottom edge of cutout.
Cabinet Installation (in inches)
B=Allow 11/16"-3/4" for overlap of oven over side edges of cutout.
(Must support 130 lbs.) ™
Advantium wall oven/GE Profile Series cooking tower
dimensions and cabinet installation information (in inches)
Note: Cabinets
installed adjacent
to wall ovens must
have an adhesion
spec of at least a
194°F temperature
rating.
Note: 2" minimum
between cutouts
when installed
above warming
drawer or single
wall oven.
Installation
Information:
Before installing,
consult installation
instructions packed
with product for ­current
dimensional data.
4-3/16"
25-1/8"
Cutout width
Note: Cabinets installed adjacent
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
4-3/16
Cabinet width
23-1/2"
Cutout depth
21-1/2"
To Back of Control
Junction box
location
(240-volt
models only)
Junction box location (240-volt models only)
A
19-1/8"
A
B
21-1/2"
19-1/8"
2-1/2" MIN between cutouts
recommended—2" MIN required
To back
of Control
29-3/4"
A
CL
B
Conduit
(46" long)
2x4’s or
17-1/2"
Cutout height
25-1/8"
Bottom Min.
3/8" Plywood Cutout widt
Supported by
2 x 4 or 1 x 2
Runners, all
Four Sides.
21-1/2"
(Must Support
To Back of Control
150 lbs.)
equivalent
Construct Solid Bottom
MIN 3/8" Plywood Supported by solid floor
2 x 4 or 1 x 2 Runners, all Four Sides.
(Must Support 150 lbs. for Advantium)
(Must Support 200 lbs. for Wall Oven)
Note: Cabinets installed adjacent
Required
29-3/4"
to wall ovens must have an adhesion
cutout location
spec of at least 194° F temperature rating.
36-3/4"
minimum
from floor
2" MIN between cutouts
cabinet
width
21-5/8"
over centerline
of cabinet
A=Allow 1" overlap of oven over bottom edge of cutout.
B=Allow 11/16"-3/4" for overlap of oven over side edges of cutout.
19-1/8"
(Must
support
130 lbs.)
1" Min.
above toekick
or adjust
to oven installation height
Note: Advantium wallovens can be installed below GE/GE Profile Series nondowndraft gas and electric cooktops. It CANNOT be installed below induction or
Monogram (2GU3841385) gas cooktops.
B
Oven Dimensions (in inches)and
Cabinet Installation (in inches) Construct Solid
9-1/4" cutout height
28-1/2" cutout width
Suitable
bracing
to support
runners
Conduit
(48-1/2"
long) Wall
Advantium
CL
4-3/16
Cabinet width
Note: Advantium wall oven comes with two lower trim pieces. One is for use above
36-inch height installations and one is for use below 36-inch installations. Use of
the accessory drawer will replace the bottom trim piece for applicable installations.
Please see installation instructions for full details.
2x4’s or
equivalent
solid floor
A
Conduit
(48-1/2"
long)
29-3/4"
Junction box location (240-volt models only)
A
19-1/8"
21-1/2"
2-1/2" MIN between cutouts
recommended—2" MIN required
To back
of Control
Suitable
29-3/4"
bracing
to support
runners
For answers to your Monogram® or GE®
appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.
Conduit
(46" long)
B
A
21-5/8"
over
centerline
B
of cabinet Construct Solid Bottom
MIN 3/8" Plywood Supported by
Listed by
Underwriters
Laboratories
cabinet
width
A=Allow 1" overlap of oven over b
(Must support 130 lbs.)
2 x 4 or 1 x 2 Runners, all Four Sides.
B=Allow 11/16"-3/4" for overlap o
(Must Support 150 lbs. for Advantium)
(Must Support
200 lbs. for Wall
Oven)
Specification
Revised
9-1/4" cutout height
28-1/2" cutout width
7/13
240409
PSB9240SF
GE Profile™ Series Advantium® 240V - 30 in. Wall Oven
Preparation with an Accessory Drawer
Prepare the opening
The Advantium 240V can be installed in combination with
other GE/Monogram appliances. Always follow each product's
Installation Instructions to compete the installation.
Single Oven Installation:
Order a 30" wide single oven cabinet or cut the opening in a wall
to the dimensions shown.
* For existing cutouts, a
23-1/2”
30”
maximum width of 28-1/2" is
acceptable. If the opening is
slightly wider, secure a furring
25-1/4”
Min.
strip on each side of the
cutout for securing the oven.
• Always maintain 36-3/4"
21”
minimum height from
Construct
Base
the floor to the cutout in
Min. 3/8”
Plywood
any single or combined
5” min.
Supported
from floor
by 2x4 or 2x2
installation.
1” min.
Runners all
• Allow 3/4" to 2-1/8" case trim
above
Four Sides
toekick
overlap on the sides and 7/8"
overlap on the bottom of the
opening for all models. The
amount of overlap on the
sides depends on the actual cutout width. Allow 1-1/4" case trim
overlap on the top for models PSB9240 and for models ZSC2200,
ZSC2201 and ZSC2202.
• Oven overlaps will conceal cut edges on all sides of the opening.
Prepare the opening (cont.)
When installed over a single oven or a
warming drawer, allow at least 2" between
the two openings. This separation will
provide clearance for bottom overlap of the
Advantium 240V and the other appliance
overlaps.
Construct a solid oven floor of 3/8" min. thick
plywood supported by 2 x 4 or 2 x 2 runners
on all sides.
• the support must be level and rigidly
mounted, flush with the bottom edge of
the
cutout.
Installation
over a GE/Monogram
Warming Drawer:
23-1/2”
30”
25-1/4”
Min.
21”
5” min.
from floor
1” min.
above
toekick
Construct
Solid Bottom
Min. 3/8”
Plywood
Supported
by 2x4 or 2x2
Runners all
Four Sides
2” Min.
(3” recommended)
Per warming
drawer
requirement
* For existing cutouts, a maximum width of
28-1/2" is acceptable. If the opening is slightly
wider, secure a furring strip on each side of
the cutout for securing the oven.
Note: Additional clearances between the
cutouts may be required. Check to be sure the
oven supports above the Warming Drawer
location do not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
Installation over a GE/Monogram Oven
and Warming Drawer:
Warming Drawer:
30”
23-1/2”
25-1/4”
Min.
21”
Construct Solid
Bottom Min.
3/8” Plywood
Supported by
2x4 or 2x2
Runners all
Four Sides
2” Min.
(3” recommended)
Per Oven
Requirement
5” min.
from floor
1” min.
above
toekick
2” Min.
Per warming drawer requirement
* F or existing cutouts, a maximum width of
28-1/2" is acceptable. If the opening is slightly
wider, secure a furring strip on each side of
the cutout for securing the oven.
Note: Additional clearances between the
cutouts may be required. Check to be sure the
oven supports above the Warming Drawer
location do not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
Caution: For personal safety, the mounting
surface must be capable of supporting the
cabinet load, in addition to the added weight
of this approximate 80-pound oven and 30pound drawer, plus additional oven loads of up
to 50 pounds or a total weight of 160 pounds.
Specification Revised 7/13
240409
PSB9240SF
GE Profile™ Series Advantium® 240V - 30 in. Wall Oven
Features and Benefits
•Speedcook Technology (240) - Enjoy oven-quality results two to eight
times faster than a conventional oven
•4 Ovens-In-1 - Expand your cooking versatility with four ovens in one
•Halogen Heat - Skip the preheating with nearly instantaneous
halogen heat
•Over 175 Preprogrammed Recipes - Preprogrammed recipes make
meals easy
•Custom Recipe Saver - Conveniently store cooking instructions for up to
30 different recipes
• Allows for use with JX2200/2201 storage drawer
•Under-the-counter installation flexibility
• Model PSB9240SFSS - Stainless steel
PSB9120/9240
Specification Revised 7/13
240409
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement