Procom FBL280TAC Series Installation manual

Procom FBL280TAC Series Installation manual
FULL SIZE VENT-FREE
FIREPLACE
OW N E R ’ S O P E R AT I O N A N D
INSTALLATION MANUAL
WARNING : If the information in this manual
is not followed exactly, a f i r e o r e x p l o s i o n m a y
r e s u l t causing property damage, personal injury,
or loss of life.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
WHAT TO DO IF YOU SMELL GAS
 Do not try to light any appliance.
 Do not touch any electrical switch;do not use any
FBN280RHAC Series Remote Control Fireplace
phone in your building.
FBL280RHAC Series Remote Control Fireplace  Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
FBN280TAC Series Thermostat Control Fireplace
instructions.
FBL280TAC Series Thermostat Control Fireplace  If you cannot reach your gas supplier, call
the fire department.
Installation and service must be performed by a
qualified installer, service agency, or the gas
supplier.
WARNING: This is an unvented gasfired heater. It uses air (oxygen) f ro m t h e r o o m
WARNING : Improper installation, adjustment,
i n w h i c h i t i s installed. Provisions for adalteration, service or maintenance can cause injury
equate combustion and ventilation air must b e
or property damage. Refer to this manual for correct
p r o vid ed . R e f er t o A ir F o r Combustion and
installation and operational procedures. For assisVentilation section on page 5 of this manual.
tance or additional information consult a qualified
installer, service agency, or gas supplier.
This appliance may be installed in an aftermarket*,
permanently located, manufactured (mo b ile) h o me,
where not prohibited by local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not
convertible for use with other gases.
Continental Appliance Inc./U.S. Office
5 Musick
Irvine
CA 92618
4600 Highlands Parkway S.E.
*Aftermarket: Completion of sale, not for purpose of resale,
from the manufacturer.
Consumer: Please retain these instructions for future
use.
Suite# D/E
Smyrna GA 30082
InstaIIer: Please Leave these instructions with the consumer
CUSTOMER CARE: 1-877-866-5989
1
www.usaprocom.com
PC-FBL035-01HR/T-0607
Table of Contents
Important Safety Information ..............2
Air for Combustion and Ventilation.....5
Installation.............................................7
Operating Heater, RHA Models........11
Operating Heater, TA Models............11
Cleaning & Maintenance.....................12
Specifications..................................... 15
Troubleshooting..................................16
Replacement ......................................17
Parts List..............................................18
Installtion Instructions........................22
Make certain you read and understand
all warnings. Keep this manual for
reference. It is your guide to safe
and proper operation of this heater.
WARNING: Any change to this firep lac e o r its c o n tro ls c a n b e
dangerous.
WARNING: Do not allow fans to
blow directly into the heater. Avoid any
drafts that alter burner flame patterns.
Ceiling fans can create drafts that alter burner flame patterns. Altered
burner patterns can cause sooting.
WARNING
Models FBN280 are equipped for Natural gas. F ield c on versio n is n ot
permitted.
Models FBL280 are equipped for Propane gas. Field conversion is not
permitted.
1. This appliance is only for use with
the type of gas indicated on the rat
ing plate. This appliance is not con
vertible for use with other gases.
2. Do not place Propane/LP supply
tank(s) inside any structure.
IMPORTIANT SAFETY
INFORMATION
IMPORTANT: Read this owner’s
manual carefully and completely
before trying to assemble, operate,
or service this heater. Improper
use of this heater can cause serious injury or death from burns,
fire, explosion, electrical shock,
and carbon monoxide poisoning.
DANGER: Carbon monoxide
poisoning may lead to death!
Carbon Monoxide Poisoning:
Early signs of carbon monoxide pois o n in g re s em b le th e f lu w it h
headaches, dizziness, or nausea.
If you have these signs, the heater
may not be working properly. Get
fresh air immediately! Have heater
serviced. Some people are more affected by carbon mon oxid e th an
o t h er s. T h e se i n c l u d e p re g n an t
women, people with heart, or lung
disease, anemia, those under the influence of alcohol, and those at high
altitudes.
Natual and Propane/LP Gas: Natural
and Propane/LP gas is odorless. An
odor-making agent is added to the gas.
The odor helps you detect a gas leak.
However, the odor added to the gas can
fade. Gas may be present even though
no odor exists.
Locate Propane/LP supply tank(s)
WARNING: Do not use a blower
insert, heat exchanger insert, or other
accessory not approved for use with
this heater.
Due to high temperatures, the appliance should be located out of traffic
and aw ay f ro m f urn it ure an d
draperies.
Do not place clothing or other flammable material on or n ear t he
appliance. Never place any objects
in the fireplace.
Heater becomes very hot w hen
running fireplace. Keep children and
adults away from hot surfaces to
avoid burns or clothing ignition.
Fireplace will remain hot for a time
after shutdown. Allow surfaces to cool
before touching.
Carefully supervise young children
wh en th ey are in t he ro om with
fireplace.
You must operate this heater with
the heater screen in place. Make
su re h eater screen is in place
before running heater.
Keep the appliance area clear and
free from combustible materials,
g a so li n e , an d o t h e r f la m m ab le
vapors and liquids.
2
outdoors.
3.



If you smell gas
Shut off gas supply.
Do not try to light any appliance.
Do not touch any electrical switch:
do not use any phone in your
building.
 Immediately call your gas supplier
from a neighbor’s phone. Follow
the gas supplier’s instructions.
 If you cannot reach your gas
supplier, call the fire department.
and to replace any part of the control system, and any gas control,
which has been under water.
4. This heater shall not be installed
in a bedroom or bathroom.
5. Do not use this heater as a
wood-burning heater. Use only
the logs provided with the heater.
6. Do not add extra logs or ornaments
such as pine cones, vermiculite, or
rock wool.Using these added items
can cause sooting. Do not add lava
rock around base. Rock and debris
could fall into the control area of
heater. After servicing, always
replace screen before operating
heater.
7. You must operate this heater with
sure heater screen is in place
before running heater.
SAFETY INFORMATION
17. Do not operate heater if any log
is broken. Do not operate heater
if any log is chipped (dime-sized
or larger).of 4,500 feet could
cause pilot outage.
18. To prevent performance
problems, do not use propane/
LP fuel tank of less than 100 lbs.
capacity.
Continued
8. This heater is designed to be
smokeless. If logs ever appear to
smoke, turn off heater and call a
qualified service person.
Note: During initial operation, slight
smoking could occur due to log
curing and heater burning manufac
QUALIFIEDINSTALLINGAGENCY
turing residues.
Installation and replacement of gas
9. To prevent the creation of soot,
piping, gas utilization equipment or acfollow the instructions in Cleaning
cessories and repair and servicing of
and Maintenance(page 12).
equipment shall be performed only by
10. Before using furniture polish, wax,
a qualified agency. The term “qualified
carpet cleaner, or similar products,
agency” means any individual, firm,
turn heater off. If heated, the vapors
corporation, or company that either in
from these products may create a
person or through a representative is
white powder residue within burner
engaged in and is responsible for (a)
box or on adjacent walls or furniture. the installation,testing,or replacement
of gas piping or(b)the connection,
11. This heater needs fresh air ventilation to run properly. This heater has installation,testing,repair,or servicing
of equipment; that is experienced in
an Oxygen Depletion Sensing
such work; that is familiar with all pre(ODS) safety shutoff system.
cautions required,and that has comThe ODS shuts down the heater if not
plied with all the requirement of the
enough fresh air is available. See Air for
authorty having jurisdiction.
Combustion and Ventilation, pages 5
through 6. If heater keeps shutting off,
PRODUCT FEATURES
see Troubleshooting, pages 14
SAFETY PILOT
through 15.
This heater has a pilot with an
12. Do not run heater:
Oxygen Depletion Sensing (ODS)
   W here flammable liquids or
safety shutoff system. The ODS/pilot
vapors are used or stored.
is a required feature for vent-free
   Under dusty conditions.
room heaters. The ODS/pilot shuts
13. Do not use this heater to cook
off the heater if there is not enough
food or burn paper or other objects. fresh air.
14. Do not use this heater if any part
MANUAL OVERRIDE CONTROL SYShas been under water. lmmediaTEM (FBN(L)280RHAC Series)
tely call a qualified service techniThi s heater has t wo operat ion
cian to inspect the room heater.
functions: Remote Control and Manual
Override Control. The Remote Control
has a transmitter, which requires three
AAA batteries and electric power outlet to operate. If no electric power is
available, then you can operate the
heater by manual override.
The ignitor require one AAA battery.
15. Turn off and unplug heater and
let cool before servicing. Only a
qualified service person should
service and repair heater.
16. Operating heater above
elevations.
3
State of Massachusetts: The installation must be made by a licensed
plumber or gas fitter in the Commonwealth of Massachusetts.
Sellers of unvented propane or natural gas-fired supplemental room heaters shall provide to each purchaser a
copy of 527 CMR 30 upon sale of the
unit.
In th e st ate of Massachusett s,
unvented propane or natural gas-fired
space heaters shall be prohibited in
bedrooms and bathrooms.
In the State of Massachusetts the
gas cock must be a “T” handle type.
The State of Massachusetts requires that a flexible appliance connector cannot exceed three feet in
length.
LOCAL CODES
UNPACKING
lnstall and use heater with care.
1. Remove top inner pack.
F o l lo w al l lo c a l c o d e s. In t h e
2. Tilt carton so that fireplace is upright.
absence of local codes, use the
3. Remove protective side packaging.
latest edition of The National Fuel
4. Slide fireplace out of carton.
Gas Code, ANSZ 223.1, also known
5. Remove protective plastic wrap.
as NFPA 54*.
6. Inastall fireplace according to instal
*Available from:
lation instructiona for corner.
American National Standards
7. Hold the screen lift and pulling
lnstitute, lnc.
forward.
1430 Broadway
8. Remove log set by cutting plastic
New York, NY 10018
ties.
National Fire Protection
9. Carefully unwrap log.
Association, lnc.
10. Check for any shipping damage. If
Batterymarch Park
stove or log is damaged, promptly
Quincy. MA 02269
inform dealer where you bought
This heater is designed for ventstove.
free operation. State and local codes
in some areas prohibit the use of
vent-free heaters.
PRODUCT IDENTIFICATION
Figure1- Vent Free LP/NG Gas Stove
WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS
Water vapor is a by-product of gas combustion. An unvented room heater produces approximately one(1) ounce
(30ml) of water for every 1,000 BTU’s(.3KW’s)of gas input per hour.
Unvented room heaters are recommended as supplemental heater(a room). Rather than a primary heat source
(an entire house). In most supplemental heat applications, the water vapor does not creat a problem. In most
applications,the water vapor enhances the low humidity atmosphere experienced during cold weather.The following
steps will help insure that water vapor does not become a problem.
1.Be sure the heater is a sized properly for the application, including ample combustion air and circulation air.
2.If high humidity is experienced,dehumidifier may be used to help lower the water vapor content of the air.
3.Do not use an unvented room heater as the primary heat source.
4
AIR FOR COMBUSTION AND VENTILATION
WARNING :
Confined and Unconfined Space
Unusually Tight Construction
The National Fuel Gas Code, ANS
Z223.1 defines a confined space as a
space whose volume is less than 50
cubic feet per 1,000 Btu per hour (4.8
m3 per kw) of the aggregate input
rating of all appliances installed in that
space and an unconfining space as a
space whose volume is not less
than 50 cubic feet per 1,000 Btu per
hour (4.8 m3 per kw) of the aggregate
input rating of all appliances installed
in that space. Rooms
communicating directly with the space in which
the appliances are installed*, through
openings not furnished with doors,
are co nsid ered a p art of th e
unconfined space.
The air that leaks around doors and
windows may provide enough fresh
air for combustion and ventilation.
However, in buildings of unusually
tight construction, you must provide
additional fresh air.
Unusually tight construction is
defined as construction where:
a) walls and ceilings exposed to the
outside atmosphere have a
continuous water vapor retarder
with a rating of one perm (6×10-11kg
p er p a- s ec -m 2 ) o r l es s w it h
openings gasketed or sealed and
b) weather stripping has been added
on windows that can be opened
and doors and
c) caulking or sealants are applied
to areas such as joints around
window and door frames, between
sole plates and floors, between
wall-ceiling joints, between wall
p an els, at p en etratio n s fo r
plumbing, electrical, and gas
lines, and at other openings.
If your home meets all of the three
criteria above, you must provide
additional fresh air. See Ventilation Air
From Outdoors (page 6).
If your home does not meet all of the
three c riteria ab ove, p ro ceed to
Determining Fresh-Air Flow For
Heater Location (below).
This heater
shall not be installed in a confined
space or unusually tight construction unless provisions are provided
for adequate combustion and ventilation air. Read the following instructions to insure proper fresh
air for this andother fuel-burning
appliances in your home.
PROVIDING ADEQUATE
VENTILATION
The following are excerpts from
National Fuel Gas Code, NFPA 54/
ANSI Z 223.1,Section 5.3, Air for
Combustion and Ventilation.
All spaces in homes fall into one of
th e t hree f ollo wing ven tilation
classifications:
1. Unusually Tight Construction
2. Unconfined Space
3. Confined Space
The information on pages 5 through 6
will help you classify your space and
provide adequate ventilation.
This heater shall not be installed in
a confined space or unusually tight
construction unless provisions are
provided for adequate combustion
and ventilation air.
* Adjoining rooms are communicating only if there are doorless passageways or ventilation grills between them.
DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION
Determining if You Have a Confined or Unconfined Space
Use this worksheet to determine if you have a confined or unconfined space.
Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways
or ventilation grills between the rooms.
1. Determine the volume of the space (length×width×height).
Length×Width×Height=
cu.ft. (volume of space)
Example: Space size 20ft. (length)×16ft.(width)×8ft. (ceiling height)=2560cu. ft. (volume of space)
If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these
rooms to the total volume of the space.
2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.
(volume of space)÷50 cu. ft.=(Maximum Btu/Hr the space can support)
Example: 2560 cu. ft. (volume of space)÷50 cu.ft.=51.2 or 51,200(maximum Btu/Hr the space can support)
5
3. Add the Btu/Hr of all fuel burning appliances in the space.
Btu/Hr
Vent-free heater
Example:
Gas water heater*
Btu/Hr
Gas water heater
30,000
Btu/Hr
Gas furnace
Btu/Hr
Vent-free
heater
+
26,000
Btu/Hr
Vented gas heater
Btu/Hr
Total
= 56,000
Btu/Hr
Gas heater logs
Btu/Hr
Other gas appliances* +
Btu/Hr
Total
=
Btu/Hr
*Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and
vents to the outdoors.
4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.
Btu/Hr (maximum the space can support)
Btu/Hr (actual amount of Btu/Hr used)
Example : 51,200 Btu/Hr(maximum the space can support)
56,000 Btu/Hr(actual amount of Btu/Hr used)
The space in the above example is a confined space because the actual Btu/Hr used is more than the
maximum Btu/Hr the space can support.
You must provide additional fresh air. Your options are as follows:
A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined
space, remove door to adjoining room or add ventilation grills between rooms. See Ventilation Air From
Inside Building (below).
B. Vent room directly to the outdoors. See Ventilation Air From Outdoors (below).
C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.
If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an
unconfined space. You will need no additional fresh air ventilation.
WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined
space or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one
of the methods described in the National Fuel Gas Code, ANSI Z223.1, Section 5.3 or applicable local codes.
Ventilation Air From lnside Building
This fresh air would come from an adjoining unconfined space. W hen ventilating to an adjoining unconfined space, you must provide two permanent openings:
one within 12" of the ceiling and one within 12" of the
floor on the wall connecting the two spaces (see
options 1 and 2, Figure 2). You can also remove door
into adjoining room (see option 3, Figure 2). Follow the
National Fuel Gas Code. NFPA 54/ANSI Z223.1, Section 5.3, Air for Combustion and Ventilation for required size of ventilation grills or ducts.
Ventilation Air From Outdoors
Provide extra fresh air by using ventilation grills or ducts.
You must provide two permanent openings: one within
12" of the ceiling and one within 12" of the floor. Connect
these items directly to the outdoors or spaces open to
the outdoors. These spaces include attics and crawl
spaces. Follow the National Fuel Gas Code, NFPA 54/
ANSI Z223.1, Section 5.3, Air for Combustion and Ventilation for required size of ventilation grills or ducts.
IMPORTANT: Do not provide openings for inlet or outlet
air into attic if attic has a thermostat-controlled power
vent. Heated air entering the attic will activate the power
vent.
WARNING: Rework worksheet, adding
the space of the adjoining unconfined
space. The combined spaces must have
enough fresh air to supply all appliances in
both spaces.
6
Figure 2 -Ventilation Air from Inside Building
Figure 3 -Ventilation Air from Outdoors
INSTALLATION
NOTICE: This heater is
intended for use as supplemental heat. Use this heater along with
your primary heating system. Do
not install this heater as your
primary heat source. If you have
a central heating system, you
may run system's circulating
blower while using heater. This
w il l h el p c i rc u la te th e h ea t
throughout the house.
WARNING: A qualified technician person must install heater. Follow all local codes.
WARNING: Never install the
heater
in a bedroom or bathroom
in a recreational vehicle
where curtains, furniture, clothing,
or other flammable objects are
less than 42 inches from the
front, top, or sides of the heater
in high traffic areas
in windy or drafty areas
Figure 4 -Minimum Clearance to Wall and Ceiling
IMPORTANT: Vent-free heaters add
moisture to the air. Although this is
beneficial, installing heater in rooms
without enough ventilation air may
cause mildew to form from too much
moisture. See Air for Combustion and
Ventilation, pages 5 through 6.
CAUTION: This heater creates
warm air currents. These currents
move heat to wall surfaces next to
heater. Installing heater next to vinyl
or cloth wall coverings or operating
heater where impurities (such as
tobacco smoke, aromatic candles,
cleaning fluids, oil or kerosene
lamps, etc.) in the air exist, may
discolor walls.
CHECK GAS TYPE
Use only the type of gas indicated on
the plate. If your gas supply can not
meet that requirement, do not install
heater. Call the dealer where you purchased heater, for the proper type of
heater.
CLEARANCESTO COMBUSTIBLES
(Vent-Free Operation Only)
Carefully follow the instructions below.
This fireplace is a freestanding unit
designed to set directly on the floor.
WARNING: Maintain the minimum clearances. If you can, provide greater clearances from floor,
ceiling, and adj oin ing side and
back walls.
7
IMPORTANT: You must maintain
minimum wall and ceiling clearances
during installation. The minimum
clearances are shown in Figure 4.
Measure from outermost point of stove
top.
Minimum Wall and Ceiling Clearances
(see Figure 4)
A. Clearances from outermost point
of stove top to any combustible side
wall should not be less than 0
inches.
B. Clearances from the stove top to
the ceiling should not be less than
48 inches.
INSTALLATION
Continued
CONNECTING TO GAS
SUPPLY
WARNING: A qualified technician must connect heater to gas
supply. Follow all local codes.
CAUTION: Never connect heater
directly to the gas supply. This heater
requires an external regulator (not
supplied). lnstall the external regulator between the heater and gas
supply.
INSTALLATION ITEMS NEEDED
Before installing heater, make sure
you have the items listed below.
piping (check local codes)
 sealant (resistant to propane/LP
gas)
 equipment shutoff valve*
 test gauge connection**
 sediment trap
 tee joint
 pipe wrench
 Flexible Gas hose(check local code)
* A CSA design-certified equipment
shutoff valve with 1/8" NPT tap is an
acceptable alternative to test gauge
connection. Purchase the optional
CSA design-certified equipment
shutoff valve from your dealer. See
Accessories.
The installer must supply an external
regulator. The external regulator will
reduce incoming gas pressure. You
must reduce incoming gas pressure
to between 11 and 14 inches of water.
If you do not reduce incoming gas
pressure, heater regulator damage
could occur. lnstall external regulator
with the vent pointing down as shown
in Figure 6. Pointing the vent down
protects it from freezing rain or sleet.
CAUTION: Only use a new black
iron or steel pipe. Internally-tinned
copper tubing may be used in
certain areas. Check you local
codes. Use pipe of 1/2" diameter or
greater to allow proper volume gas
to heater. If pipe is too small, undue
loss of pressure will occur.
Installation must include an equipment shutoff valve, union, and
plugged 1/8" NPT tap. Locate NPT
tap within reach for test gauge hook
up. NPT tap must be upstream
from heater (see Figure 7).
Propane/LP
Supply Tank
Figure 5 -Gas Regulator Location
and Gas Line Access Into Stove
Cabinet
CAUTION: Use pipe joint sealan t t hat is resistant t o g as
(PROPANE or NG).
W e recommend that you install a
sediment trap in a supply line as
shown in Figure 7. Locate sediment
trap where it is within reach for cleaning.
Install in the piping system between
fuel supply and heater. Locate sediment trap where trapped matter is not
likely to freeze. A sediment trap traps
mo istu re and c ont amin ants. Th is
keeps them from going into heater
controls. If sediment trap is not installed or is installed incorrectly,
heater may not run properly.
CAUTION: Avoid damage to
regulator. Hold gas regulator with
wrench when connecting into gas
piping and/or fittings.
NG Models:
5” to 10.5” W.C.
Gas supplier provide external
regulator for natural gas
WARNING: Never connect
heater to private (non-utility) gas
wells. This gas is commonly known
as wellhead gas.
Front View
IMPORTANT: Inst all equ ipment
shutoff valve in an accessible location.
The equipment shutoff valve is for
turning on or shutting off the gas to
the appliance. Apply pipe joint sealant
lightly to male threads.This will prevent excess sealant from going into
pipe. Excess sealant in pipe could
result in clogged heater valves.
Figure 6 -External Regulator With
Vent Pointing Down
Figure 7 -Gas Connection
* Purchase the optional CSA design-certified equipment shutoff valve
from your dealer. See Accessories.
** Minimum inlet pressure for purpose of input adjustment.
8
INSTALLATION
Continued
CHECKING GAS CONNECTIONS
WARNING: Test all gas piping
and connections for leaks after
installing or servicing. Correct all
leaks immediately.
WARNING: Never use an open
flame to check for a leak. Apply a
mixture of liquid soap and water to
all joints. Bubbles forming show a
leak. Correct all leaks immediately.
Pressure Testing Gas
Supply Piping System
Pressure Testing Heater
Gas Connections
1. Open equipment shutoff valve
(see Figure 8).
2. Open gas supply tank valve.
3. Make sure control knob of heater is
in the OFF position.
4. Check all joints from equipment
shuto ff valve t o control valve
(Figure 9). Apply mixture of liquid
soap and water to gas joints.
Bubbles forming show a leak.
5. Correct all leaks immediately.
6. L ig ht heat er (see O pe ra t in g
Heater, page 11).Check all other
internal joints for leaks.
7. Turn off heater (see Operation of
Turn-Off , page 11).
Test Pressures In Excess Of 1/2
PSIG(3.5kPa)
1. Disconnect
heater with its
appliance main gas valve (control
valve) and equipment shutoff valve
from gas supply piping system.
Pressures in excess of 1/2 psig
will damage heater regulator.
2. Cap off open end of gas pipe
where equipment shutoff valve
was connected.
3. Pressurize supply piping system
by either using compressed air or
opening gas supply tank valve.
4. Check all joints of gas supply
piping system. Apply mixture of
liquid soap and water to gas
joints. Bubbles forming show a
leak.
5. Correct all leaks immediately.
6. Reconnect heater and equipment
shutoff valve to gas supply. Check
reconnected fittings for leaks.
CAUTION: Make sure external
regulator has been installed between gas supply and heater. See
guidelines under Connecting to Gas
Supply (page8).
Test Pressures Equal To or
Less Than 1/2 PSIG(3.5 kPa)
1. Close equipment shutoff valve
(see Figure 8).
2. Pressurize supply piping system
by either using compressed air
or opening gas supply tank valve.
3. Check all joints from gas meter to
equ ipmen t shutof f valve(see
Figure 9). Apply mixture of liquid
soap and water to gas joints.
Bubbles forming show a leak.
4. Correct all leaks immediately.
Figure 8 -Equipment Shutoff Valve
Figure 9 -Checking Gas Joints
9
INSTALLATION
Continued
INSTALLING LOGS
WARNING: Failure to position
the parts in accordance with these
diagrams or failure to use only parts
may result in property damage or
personal injury.
CAUTION: After installation and
periodically thereafter, check to ensure that no flame comes in
contact with any log. With the heater
set to High, check to see if flames
contact any log. If so, reposition logs
according to the log installation
instructions in this manual. Flames
contacting logs will create soot.
Figure 10 -Installing Log Set
IMPORTANT: Make sure log does not cover any burner ports (see
Figure 10).
It is very important. To install the logs exactly as instructed. Do not modify
logs. Only use logs supplied wall heater.
FIG(1)
FIG(2)
1. All logs. See FIG(1).
STEP 1: Install the log 1on the left
rear angle iron. See FIG(2).
FIG(3)
FIG(4)
STEP 2:Install the log 2 on the right rear
STEP 3:Install the log 3 on the front
iron. See FIG(3).
angle. See FIG(4).
FIG(5)
FIG(6)
STEP 4:Insert the pinhole on the upper
STEP 5:Insert the pinhole on the upper
part on the left side of log 1. Place the
part of log 5 in the pin on the log 2. Place
the lower part of log 5 on the flat roof at
lower part of log 4 on the flat roof at the left
side of log 3. See FIG(5).
10
the left side of log . See FIG(6).
OPERATING
HEATER
FOR YOUR SAFETY
RHA Series Models
WARNING: If you do not
follow these instructions exactly, a
fire or explosion may result causing
property damage, personal injury or
loss of life.
NOTICE: During initial operation
of new fireplace, burning logs will
give off a paper-burning smell. Orange flame will also be present.
Open a window to vent smell. This
will only last a few hours.
CAUTION: Do not try to adjust
h eat in g levels b y using th e
equipment shutoff valve.
A. This appliance has a pilot which
must be lighted by control system,
W hen lighting the pilot, follow
t h e se in s t ru c t io n s
e xa c t l y .
B . B E F O R E L I G H T I N G sm ell all
around the appliance area for
gas. Be sure to smell next to the
floo r b ec au se som e g as is
heavier than air and will settle
on the floor.
WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch;
do not use any phone in your
building.
Immediately call your gas sup
plier from a neighbor’s phone.
Follow the gas supplier’s
instructions.
If you cannot reach your gas
supplier, call the fire department.
C. Use only your hand to push in
control knob. Never use tools. If the
the appli ance could not operate , don't
try to repair it, Call a qualified service
technician or gas supplier.Forced or attempted re-pair may result in a fire or
explosion.
D. Do not use this appliance if any
part has been under water. Immediately call a qualified service technician to inspect the appliance and to
replace any part of the control system
and any gas control which has been
under water.
Note: To operate your heater the ON/
OPERATIONS OF
REMOTETRANSMITTER
1. Install three AAA batteries in the
battery holder. The initial start-up on
the LCD is: SET TEMP is 85°F,
ROOM TEMP is 85°F, and fan is on
“AUTO” select.
OFF switch on front of heater must be
in the ON position. The RED light on
the front of heater indicates there is
electrical power to your heater when
the ON/OFF switch is in the ON position. The GREEN light on the front of heater indicates the pilot light
is ON. (See Figure 11)
Note: Please wait one minute after
shutting off fireplace to allow the
electronic module to reset before
starting again.
LIGHTING INSTRUCTIONS
Note: If operating by remote control,
you must set the Control Knob on
ELECTRIC position.
Fig 12 Initial start-up on the LCD
2. When in operation, point the
remote transmitter to the remote
receiver on the front of fireplace at
a maximum distance of 20 feet
without any obstruction between
them.
OPERATIONS OF
BURNER
Do not set the control knob between 1. Before plugging into the outlet
make sure that the appliance is
the locked position, otherwise there
connected to the gas supply. Plug
will be no power to the heater.
fireplace into a properly grounded
1. STOP! Read the safety information,
120 Volt, 60Hz, 15 amp outlet. You
page 2.
will hear a high pitch sound and
2. Make sure equipment shutoff
power light(red) on the door will
valve is fully open.
be lit that indicates that the
burner is ready to be operated.
2. Point the remote transmitter to
Function of power ON/OFF swith.
the burner. Press IGN/OFF button,
the electric spark starts igniting
the pilot and then the burner. Wait
five (5) minutes to clear out any
air. If you smell gas. STOP!
Please check the gas connection.
The green operation light on the
front of fireplace will be lit when
pilot and burner are on.
Figure 11 - ON/OFF Switch location
11
Note: The main burner does not
respond immediately to the set
temperature until about one
minute later.
3. To shut off, press IGN/OFF button
on remote or on front of fireplace.
Note: The pilot will also shut off.
OPERATING HEATER
Continued
a. Set temperature: Press “Temp”
button, then press or to set desired
room temperature. Burner will operate
to maintain set room temperature.
MANUAL OVERRIDE
CONTROL SYSTEM OPERATING
INSTRUCTIONS
We provide the manual override control system in the event of power
outage.
Install battery for manual Ignitor:
1. Unscrew the ignitor cap.
2. Insert a AAA type battery with its
anode (“+”) pointing out.
3. Screw the ignitor cap back.
Fig13 Control board
Note: W e recommend that the battery
b. Set blower: Press “FAN” button. the be taken out of the ignitor when the
blower will shift between “AUTO” and power supply resumes.
“OFF” option.
W hen “FAN” is in “AUTO” select: the
blower will be oprate depend on the temperature inside the heater. and automatically turn ON or OFF.
When Fan is in “OFF” select the blower
will not operate.
LIGHTING INSTRUCTIONS
If power is off, you can operate the
fireplace manually.
1. STOP! Read the safety information
on page 11.
2. Check that gas supply to heater is
on.
3.
Open bottom front access panel.
OPERATIONS OF
4.
With
Control Knob in the on ELECTIMER
TRIC
position, press in the Control
A uto o ff: w hen t h e bu rner is in
Knob
and turn counterclockwise to
operation, press TIMER button. Then
OFF
position.
press
or to change to the schedNOTE: Knob cannot be turned
uled time, then press the TIMER button
from
PILOT/IGN to “OFF” unless
again, the TIMER starts timing and the
knob
is pushed in slightly. Do not
TIMER will flash and the green operaforce.
tion light flashes. Burner will automati5. Wait five (5) minutes to clear out
cally shut off at set time.
any gas. Then smell for gas,
LOCKING REMOTE
including near the floor. If you smell
gas, STOP! Follow “B” in the safety
CONTROL
information on page 11. If you do
( child proof )
not smell gas, go to the next step.
1. To Lock: Press
LOCK button , a
6. Push in gas control slightly and turn
symbol will appear on control board.
counterclockwise to PILOT/IGN
2. To Unlock: Press LOCK button and
and depress for five (5) seconds.
hold until lock image shows
unNOTE: The first time that the heater
locked (typically 6 secs.).
is operated after connecting the
gas supply, the control knob should
be depressed for about thirty (30)
seconds. This will allow air to
bleed from the gas system.
7. With Control Knob pressed in,
push ignitor button. This will light
the pilot. If needed, keep ignitor
button until pilot lights.
Fig14 “AUTO” select
12
8. Keep Control Knob depressed for
ten (10) seconds after lighting
pilot. If pilot goes out, repeat steps
6, 7 and 8.
9. Turn counterclockwise to “ON”
position. Do not operate between
locked positions.
TO TURN OFF GAS
TO APPLIANCE
Shut off heater
Push in gas Control Knob slightly
and turn clockwise
to the OFF
position. Do not force.
W hen electric power is available and
electric operation is desired, turn
clockwise
to OFF position for
one minute to allow the electronic
module to reset before starting. Then
press down knob and rotate clockwise
to ELECTRIC position.
Do not operate between locked
positions.
MANUAL LIGHTING
PROCEDURE
(match light)
1. Open front door.
2. Follow steps 1 through 5 under
MANUAL OPERATING Lighting
Instructions.
3. With Control Knob in PILOT/IGN
position, strike match, and hold
near pilot. Press in Control Knob,
pilot should light.
4. Keep Control Knob pressed in for
30 seconds after lighting pilot.
After 30 seconds, release Control
Knob. Follow step 9 under
MANUAL OVERRIDE CONTROL
SYSTEM OPERATING
INSTRUCTIONS.
INSPECTING BURNERS
Check pilot flame pattern and burner
flame patterns often.
TO TURN OFF GAS TO APPLIANCE
Shut off heater
1. Press the IGN/OFF button.(see figure 15)
2. Set the ON/ OFF Switch position or
unplug the electric power to the heater.
PILOT FLAME PATTERN
DISCONNECT FAN
F igu re 15 sh ow s a c o rrec t p ilo t
flame pattern. Figure 16 shows an
incorrect pilot flame pattern. The
incorrect pilot flame is not touching
the thermocouple.This will cause the
thermocouple to cool. W hen the
thermocouple cools, the heater
will shut down. If pilot flame pattern
is incorrect, as shown in Figure 18
 Turn heater off (see TO TURN OFF
GAS TO APPLIANCE, page 9)
 see troubleshooting, page 15.
1.
Remove screws from the fan
bracket panel , pull the fan bracket
panel out to remove. Then disconnect two wires free to fan.
2.
Figure 18 -Incorrect Flame Pattern
with Control Knob Set to High Flame
Mark or tag each wire removed
for its exact reconnection. Remove
the four screws from the fan .when
installing , reverse the steps above.
CLEANING AND MAINTENANCE
(See Figure 20 and Figure 22)
WARNING: Disconnect power before attempting any maintenance or
cleaning to reduce the risk of fire , electric shook or personal injury. Turn off
heater and let cool before cleaning.
Figure 20- Fan
CAUTION:Label all wires prior to
disconnection when servicing
controls
. Wiring errors can cause
Figure 15 -Correct Pilot Flame Pattern
improper and dangerous operation.
Verify proper operation after servicing.
DISCONNECT WIRNG OR CONTROL
MODULE
1. Remove four screws from the rear
control panel , take out thermostat
sensing bulb from the clip, then disconnect the wires to free to control
Figure 16 -Incorrect Pilot Flame
Pattern
BURNER FLAME PATTERN
Figure 17 shows a correct burner
flame pattern. Figure 18 shows an
incorrect burner flame pattern. If
burner flame is incorrect:
 Turn heater off (see TO TURN OFF
GAS TO APPLIANCE, page 10)
 see troubleshooting, page 15.
module from its mounting location .
Note: Do not confuse the mark on
the each wire.
2. Remove two screws and hex nuts,
take out the control module. W hen installing , reverse the steps above.
(See Figure 19 and Figure 22)
Figure 19- Control Model
Figure 17 -Correct Flame Pattern
with Control Knob Set to High Flame
13
WARNING: Failure to keep
primary air openings of burners clean
may result in sooting and property
damage.
CAUTION: You must keep control
areas, burner, and circulating air passageways of heater clean. Inspect
these areas of heater before each
use. Have heater inspected yearly by
a qualified service person. Heater
may need more frequent cleaning due
to excessive lint from carpeting,
bedding material, pet hair, etc.
CLEANING ODS/IGNITOR AND
BURNER
Clean with a vacuum cleaner.
CLEANING BURNER
INJECTOR HOLDER AND
PILOT AIR INLET HOLE
We recommend that you clean the unit
every three months or after 2500 hours
of operation. We also recommend that
you keep the burner tube and pilot assembly clean and free of dust and
dirt. To clean these parts we recommend using compressed air no greater
than 30 PSI. You can use a vacuum
cleaner in the blow position. If using
compressed air in a can, please follow the directions on the can. If you don't
follow directions on the can, you could
damage the pilot assembly.
CLEANING AND MAINTENANCE
Continued
inlet hole about two inches from
where the pilot flame comes out of
the pilot assembly (see Figure 22).
With the unit off, lightly blow air
through the air inlet hole. You may
blow through a drinking straw if
compressed air is not vailable.
Figure 21 -Injector Holder On Outlet
Burner Tube
1. Shut off the unit, including the
pilot. Allow the unit to cool for at
least thirty minutes.
2. Inspect burner, pilot and primary air
inlet holes on injector holder for
dust and dirt (see figure 21).
3. Blow air through the ports/slots
and holes in the burner.
4. Check the injector holder located
at the end of the burner tube
again. Remove any large particles
of dust, dirt, lint, or pet hair with a
soft cloth or vacuum cleaner
nozzle.
5. Blow air into the primary air holes
on the injector holder.
6. In case any large clumps of dust
have now been pushed into the
burner, repeat steps 3 and 4.
Clean the pilot assembly also. A
yellow tip on the pilot flame
indicates dust and dirt in the pilot
assembly. There is a small pilot air
Figure 22 -Pilot Air Inlet Hole
CABINET
Air Passageways
 Use a vacuum cleaner or
pressurized air to clean.
Exterior
Use a soft cloth dampened with a
mild soap and water mixture. Wipe
the cabinet to remove dust.
LOGS
If you remove logs for cleaning,
refer to Installing Logs (page 10)
to properly replace logs.
 Replace logs if broken or chipped
(dime-sized or larger).
MAIN BURNER
Periodically inspect all burner flame
holes with the heater running. All
slotted burner flame holes should
be open with yellow flame present. All
round burner flame holes should be
o p e n w ith a s m a ll b lu e flam e
present. Some burner flame holes
may become blocked by debris or
rust, with no flame present. If so,
turn off heater and let cool. Either
remove blockage or replace burner.
B lo c k ed b u rn er f lam e h o les w ill
create soot.
Figure 22- Remote Control System Diagram
14
SPECIFICATIONS
FBL280TAC
FBL280RHAC
Btu(Variable)
Gas Type
Ignition
Manifold Pressure
Inlet Gas Pressure
(In. of water)*
Maximum
Minimum
Dimensions, Inches (H×W ×D)
Heater
Carton
Weight, lbs
Stove
Shipping
Voltage
Watt
28000
LP Gas
Piezo/Automatic
8"W.C.
14"
11"
36 1/4”×53 13/16”×29 1/2”
40 5/8”×54 3/4”×18 1/8”
130
157
120
27
*For purposes of input adjustment
15
FBN280TAC
FBN280RHAC
28000
Natural Gas
Piezo/Automatic
3"W.C.
10.5"
5"
36 1/4”×53 13/16”×29 1/2”
40 5/8”×54 3/4”×18 1/8”
130
157
120
27
TROUBLESHOOTING
WARNING: If you smell gas
Shut off gas supply.
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your
building.
Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
WARNING:Make sure that power
is turn off before proceeding....
OBSERVED PROBLEM
WARNING: Turn off and let cool
before servicing. Only a qualified
service person should service and
repair fireplace.
POSSIBLE CAUSE
CAUTION: Never use a wire,
needle, or similar object to clean
ODS/pilot. This can damage ODS/
pilot unit.
REMEDY
No spark when ignition button is
pressed.
1. No power to heater
2. No battery in transmitter or battery
isn’t correctly assembly
1. Check the electric power
2. Place or replace the battery.
Spark at ODS/pilot but no ignition
1. Gas supply turned off or equipment shut off valve closed
2. Air in gas lines when installed.
1. Turn on gas supply or open equipment shutoff valve
2. Press ON/OFF button again
until air is removed .
3. Contact local propane/LP gas
company
4 Clean ODS/pilot (see Cleaning
and Maintenance,page 13 ) or
replace ODS/pilot assembly
5. Replace gas control
6. Replace Pilot
3. Depleted gas supply
4. ODS/pilot is clogged
5. Gas regulator setting is not correct
6. Pilot electrude position is not
correct
7. W ire is not correct or loosen
8 Gas valve is damage
ODS/pilot lights but flame is continuous igniting and the main burner
couldn’t be lit.
1. Thermocouple connection loose
at control board
2. Pilot flame not touching
thermcouple which allows thermocouple to cool, causing pilot
flame to go out. This problem
could be caused by one or both of
the following
A) Low gas pressure
B) Dirty or partially clogged
ODS/ pilot
3. Thermocouple damaged
4. Control valve damaged
16
7. Check the wine and make wine
correct.
8. Contact dealer or procom.
1. Hand tighten until snug, then
tighten 1/4 turn more.
2. A) Contact local propane/LP gas
company.
B) Clean ODS/pilot (see Cleaning
and Maintenance, page 13) or
replace ODS/pilot assembly
3. Replace thermocouple
4. contact dealer or procom.
TROUBLESHOOTING
Continued
Burner does not light after ODS/pilot
is lit
1.
Burner orifice clogged
2. Inlet gas pressure is too low
3. Burner orifice diameter is too
sm all
4. Thermocouple leads disconnected or improperly connected
5. Burners will not come in
remote position
1.Clean burner (see Cleaning
and Maintenance, page 13) or
replace burner orifice.
2. Contact local propane/LP
gas company
3. Replace burner orifice
4. Reconnect leads (see wiring
diagram)
5. Replace battery in transmitter
and receiver
Delayed ignition burner
1. Manifold pressure is too low
2. Burner orifice clogged
1. Contact local gas company
2. Clean burner (see Cleaning and
Maintenance, page 13)
Burner backfiring during combustion
1. Damaged burner
1. Clean burner orifice (see
Cleaning and Maintenance, page
13)
2. Replace gas regulator
2. Gas regulator defective
Slight smoke or odor during initial
operation
1. Residues from manufacturing
processes
2. Not enough air
3. Gas regulator defective
1. Problem will stop after a few
hours of operation
2. Check burner for dirt and debris.
If found, clean burner (see Cleaning
and Maintenance, page 13)
3. Replace gas regulator
Dark residue on logs or inside of
fireplace
1. Improper log placement
2. Air holes at burner inlet blocked
3. Burner flame holes blocked
1. Properly locate logs (see installing
logs, page 10)
2. Clean out air holes at burner inlet.
Periodically repeat as needed.
3. Remove blockage or replace burner
Heater produces a clicking/ticking
noise just after burner is lit or
shut off
1. Metal expanding while heating
or contracting while cooling
1. This is common with most
heaters. If noise is excessive,
contact qualified technician.
REPLACEMENT PARTS
 Your name
 Your address
NOTE: Use only original replace Model and serial numbers
ment
parts. This will protect your warranty of your heater
coverage for parts replaced under  How heater was malfunctioning
 Type of gas used (propane/LP or
warranty.
NG)
PARTS UNDER WARRANTY
 Purchase date
Contact authorized dealers of this
Warranty card
product. If they can't supply original
 Usually, we will ask you
replacement part(s), call ProCom’s
to return the defective part to the
toll free number at (1-877-886-5989)
factory.
for referral information.
W hen calling PRroCom or your
dealer, have ready:
REPLACEMENTPARTS
17
PARTS NOT UNDER
WARRANTY
Contact authorized dealers of this
product. If they can’t supply original replacement part(s) call ProCom’s toll free
number at (1-877-886-5989) for referral
information.
When calling ProCom, have ready
 Model number of your heater
 The replacement part number
PARTS LIST
FBN280TAC
FBL280TAC
This list contains replaceable parts used in your heater. When ordering
parts, follow the instructions listed under Replacement Parts on page 17
of this manual.
KEY NO PART NUMBER
DESCRIPTION
QUALITY
LP NG
1
2
3
4
5
6
7
8
SIT545-218
SIT545-200
NRV81F1-3
NRV81F1-8
BL023-01
BL024-01
NBY28-025B3
NBY28-160B3
ND1703X400X4
ND1908X400X4
FBB106
FBB104
FBB105
T-STAT VALVE
T-STAT VALVE
REGULATOR
REGULATOR
INJECTOR
INJECTOR
BURNER ASSEMBLY
BURNER ASSEMBLY
ODS
ODS
ODS INLET TUBE ASSEMBLY
INLET TUBE ASSEMBLY
OUTLET TUBE ASSEMBLY
18
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
PARTS LIST
FBN280TAC
FBL280TAC
This list contains replaceable parts used in your heater. When ordering
parts, follow the instructions listed under Replacement Parts on page 17
of this manual.
KEY NO PART NUMBER
DESCRIPTION
QUALITY
LP NG
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
BB26000
LOGS
1
1
FB280AC6-01
TOP PANEL
1
1
FB280AC6-03
SIDE PANEL
1
1
FB280AC6-04
SIDE PANEL
1
1
FB280AC6-05
BASE
1
1
FB280AC6-02
FBL001-01
UPPER PANEL
1
1
BODY TOP COVER
1
1
FBL008-01B
BAFFLE
1
1
FBL006-01B
SIDE REFLECTOR
2
2
FBL007-01A
FIREBOX FLOOR
1
1
FBL002-01
LOUVER
8
8
FBL001-03RH
BODY BOTTOM COVER
1
1
FBL001-02S
BODY BOARDING
1
1
FBL010-01B
UPPER PANEL
1
1
FBB102
SCREEN
1
1
ML083-02
IGNITOR
1
1
FBL015-01
T-STA VALVE BRACKET
1
1
QL016-03R
BLOWER MOUNT PANEL
1
1
PF06-YJLF-F
FAN
1
1
19
PARTS LIST
FBN280RHA
FBL280RHA
KEY NO
1
2
3
4
5
6
7
8
9
This list contains replaceable parts used in your heater. When ordering
parts, follow the instructions listed under Replacement Parts on page 17
of this manual.
PART NUMBER
NV2020-22*
BL015-03RA
FBB33000RH
FBB31000RH
NRV81F1-3
NRV81F1-8
ND4703X400-RH
ND4808X400-RH
NBY28-025B3
NBY28-160B3
BL023-01
BL024-01
FBB32000RH
DESCRIPTION
QUALITY
LP NG
1
1
T-STAT VALVE BRACKET
1
1
ODS INLET TUBE ASSEMBLY
1
1
INLET TUBE ASSEMBLY
1
1
REGULATOR
1
REGULATOR
1
ODS
1
ODS
1
BURNER ASSEMBLY
1
BURNER ASSEMBLY
1
INJECTOR
1
INJECTOR
1
OUTLET TUBE ASSEMBLY
1
1
OVERRIDE CONTROL SYSTEM
20
PARTS LIST
FBN280RHA
FBL280RHA
Key No.
1
2
3
4
5
6
This list contains replaceable parts used in your heater. When ordering
parts, follow the instructions listed under Replacement Parts on page 17
of this manual.
Part Number
QL016-03R
PF06-YJLF-F
NAYB03-00
NAYB01-00
NAYB02-00
FBB102
Description
BLOWER MOUNT PANEL
BLOWER
CONTROL CABINET ASSEMBLE
REMOTE
RECEIVER ASSEMBLE
SCREEN
21
QTY
1
1
1
1
1
1
INSTALLATION INSTRUCTIONS
For CORNER SURROUND AND HEARTH
READ INSTRUCTIONS BEFORE BEGINNING INSTALLATION. Check to see that you have
the following. If any part or parts are missing, contact the dealer where you bought the surround and hearth.
TOOLS REQUIRED:
Measuring Tape, Pencil, Level, #2 Phillips Screw Driver, Hammer, Electric Drill, 5/6" Drill Bit,
Hand or Electric Saw
INSTALLATION:
1. Surround must be installed flush with wall. Baseboards
wi ll pr ev ent p ro per i nst al lat io n o f su rro un d.
Baseboards can be altered to fit surround by cutting
that part within 34 1/2” distance from the wall corner.
2. Surround must be attached to either a wall stud or wall
anchor. Use a tape measure to determine correct
height from floor to location of mounting strips. (See
Figure 1). Make sure point of the mitered edge of
mounting strip touches the corner. Use a level to ensure mounting strips are evenly balanced.
IMPORTANT: Failure to balance mounting strips
with a level could result in uneven surfaces on
fully assembled surround.
3. Fasten mounting strip to wall by inserting 2" screws
provided along the predrilled holes of mounting strip.
If predrilled holes of mounting strip do not line up with
wall studs, drill new holes where wall studs are or attach to wall with wall anchors. (See Step 4 below.)
4. To use wall anchors, drill holes at marked location
using 5/16” drill bit. Fold wall anchor (see Figure 2)
and insert (wings first) into hole. Tap anchor flush into
wall. For thin walls, insert red key into wall anchor and
push to “pop” open anchor wings (see Figure 3).
5. Repeat steps above to attach other mounting strips
to wall. Make sure mitered edges fit together to form
a clean joint in the corner of the wall.
22
19 1/2”
19 1/2”
Figure 1
Figure 2
Figure 3
6. Place the assembled fireplace on the middle where it is 30” from the corner and
form a 45 degree angle to each side wall. Move the assembled surround to the
corner, with side panels close to side walls. Move the fireplace to where it can properly attach the surround.
7. Move the surround away, mark floor or wall behind fireplace for gas line entrance.
Connect inlet gas pipe.
IMPORTANT: Make sure there are no electrical lines where gas piping will
go through floor or wall.
8. Turn up the back of mantel top, the special spring will lock the rear mantel top in
position, then use screws to secure bracket as show in Figure 5 make sure the front
and rear mantel top are in the same level.
9. Move the surround back. Set surround top on top of mounting strips and mantel
front. After properly installing the top, attach surround top to mounting strip using
finishing nails.
10.Push the base to the bottom of surround, close to the right and left sides.
11. Install fireplace per Homeowner’s Installation Manual.
19 11/16”
Figure 4
Figure 5
Figure 6
23
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement