Mi-T-M Pressure Washer Specifications

Mi-T-M Pressure Washer Specifications
8650 Enterprise Drive, Peosta IA 52068-0050
319-556-7484 / Fax 319-556-1235
PARTS LIST FOR
HSP-3504-1MGH/1MGV
(After Serial #22654)
ENGINE OIL GRADE:
HONDA:
VANGUARD:
©
Copyright 1999, Mi-T-M Corporation
ENGINE OIL CAPACITY:
HONDA:
VANGUARD:
PUMP OIL GRADE:
PUMP OIL CAPACITY:
FUEL NOZZLE:
BTU INPUT:
PRESSURE NOZZLE SIZE:
SAE 10W-30
ABOVE 40°F=SAE30
BELOW 40°F=SAE10W-30
1
37 OZ.
51 OZ.
Mi-T-M PUMP OIL #AW-4085-0016
23.7 OZ.
1.75 60°B DELAVAN
294,000 / HOUR
3.5
EX-9056-052199R1-1C
Issue Date: 102097
This Parts Listing has been compiled for your benefit. You can be assured your Mi-T-M hot water pressure washer was constructed and designed with quality
and performance in mind. Each component has been rigorously tested to insure the highest level of quality.
The contents of this Parts Listing are based on the latest product information available at the time of publication. Mi-T-M reserves the right to make changes in
price, color, materials, equipment, specifications or models at any time without notice.
WARNING
THIS IS A PROFESSIONAL HIGH PRESSURE, HOT WATER PRESSURE WASHER. CAUTION SHOULD BE OBSERVED WHEN USING
OR REPAIRING THIS UNIT! READ AND FOLLOW THE SAFETY WARNINGS LISTED BELOW BEFORE ATTEMPTING ANY REPAIRS ON
THIS PRESSURE WASHER!
SAFETY WARNINGS
1.
NEVER alter or modify the equipment. Be sure any accessory items and system components being used will withstand the pressure developed. Use
only genuine Mi-T-M parts for repair of your pressure washer. Failure to do so can cause hazardous operating conditions and will VOID warranty.
2.
NEVER make adjustments on machinery while the unit is connected to the engine without first removing the ignition cable from the spark plug.
Turning over the machinery by hand during adjustment or cleaning might start the engine and machinery with it, causing serious injury to the operator.
3.
Know how to stop and bleed pressures quickly. Be thoroughly familiar with controls.
4.
Before servicing the unit, turn unit off, relieve the water pressure and allow the unit to cool down. Do not make repairs while the unit is running.
Service in a clean, dry, flat area. Block the wheels to prevent the unit from moving. Be especially careful to properly dispose of any flammable materials.
5.
After testing the machine, DO NOT leave the pressurized unit unattended. Shut off the unit and release trapped pressure before leaving.
Table of Contents
SPECIFICATIONS ................................................................................................................................................................................................................................ 3
FLOW CHART ...................................................................................................................................................................................................................................... 4
EMF SYSTEM ....................................................................................................................................................................................................................................... 4
GENERAL THEORY OF OPERATION ................................................................................................................................................................................................... 5
DECAL PLACEMENT ........................................................................................................................................................................................................................... 6
FRAME ................................................................................................................................................................................................................................................. 8
ENGINE/PUMP ASSEMBLY ................................................................................................................................................................................................................ 10
HIGH PRESSURE PUMP (3-0144) ....................................................................................................................................................................................................... 12
PUMP SERVICE GUIDE ...................................................................................................................................................................................................................... 14
UNLOADER/MANIFOLD ASSEMBLY .................................................................................................................................................................................................. 16
UNLOADER (850-0252) ........................................................................................................................................................................................................................ 18
PRESSURE SETTING & TROUBLESHOOTING THE UNLOADER ...................................................................................................................................................... 19
PRESSURE SWITCH (850-0173) ......................................................................................................................................................................................................... 20
DETERGENT INJECTOR (50-0052) ...................................................................................................................................................................................................... 21
COIL DRAIN PLUG (850-0218) ............................................................................................................................................................................................................ 21
HEAT EXCHANGER/EMF SYSTEM ..................................................................................................................................................................................................... 22
BOILER ASSEMBLY (850-0226) .......................................................................................................................................................................................................... 24
GUN (850-0181) & ADJUSTABLE PRESSURE DUAL LANCE (850-0180) ............................................................................................................................................ 26
FUEL TANK (850-0248) ........................................................................................................................................................................................................................ 28
FUEL PUMP (3-0020) & FUEL SOLENOID (44-0100) .......................................................................................................................................................................... 30
ELECTRIC BOX .................................................................................................................................................................................................................................. 32
WIRING SCHEMATIC .......................................................................................................................................................................................................................... 34
WIRING
DIAGRAM .............................................................................................................................................................................................................................. 35
©
Copyright 1999, Mi-T-M Corporation
EX-9056-052199R1-1C
2
Issue Date: 102097
SPECIFICATIONS
HSP-3504-1MGH/GV
MODEL NUMBER
Operating Pressure (PSI/Bar):
Water Volume (GPM/lpm):
Outlet Water Temperature (F/C):
Engine:
Horsepower
Engine Type
Oil Type
Oil Capacity (oz./liter)
Low Oil Protection
Fuel Type
Fuel Capacity (gal./liter)
Starting
HSP-3504-1MGH
HSP-3504-1MGV
3500/ 241 (+/- 5%)
3.3/12.5 (+/- 5%)
140 F/ 78 C (+/- 20 F) rise above inlet ambient (210 F/ 99 C maximum)
Honda
Briggs & Stratton Vanguard
13
13
Four Stroke, Overhead Valve, Single Cylinder
SAE10W-30
Above 40 F=SAE30/ Below 40 F=SAE 10W-30
37/1.1
Oil AlertTM
51/1.5
Oil Guard TM
Unleaded Gasoline 86 Octane Minimum
1.72/6.5
1.8/6.8
Recoil Rope
Maximum No Load RPM
High Pressure Pump:
3600 (+/- 100)
Direct Driven, Oil Bath, Triplex Piston
Mi-T-M Pump Oil #AW-4085-0016
23.7/0.7
Oil Type
Oil Capacity (oz./liters)
Plungers
Manifold
Valves
Unloader
Inlet Water Strainer
Heat Dump Valve
Detergent Injector:
Ceramic
Forged Brass
Stainless Steel
Preset
Removable Clear Bowl for inspection and cleaning of Stainless Steel Screen
Relieves heated water during unloader bypass stage
Adjustable Low Pressure downstream from pump
Burner Fuel System:
Fuel Type
Fuel Capacity (gal./liters)
Fuel Filter/ Water Separator
Fuel Pump
No.1 or No.2 Fuel Oil, Diesel or Kerosene
5.5/21
Spin on (10 micron) filter/ E-Z water drain
Two Line, Single Stage
Fuel Pressure (PSI/ BAR)
Fuel Nozzle
Fuel Consumption (GPH/ LPH)
Electro Magnetic Firing (EMF) System:
145/10
1.75 60 B Delavan
2.1 GPH Continous Burning
Belt Driven (Patent Pending)
Transistorized Magneto
Ignition
Control Voltage
Blower
Heat Exchanger:
BTU Input
12 Volt DC
Forced Air
Vertical, Top fired, Dual Spiral Coil
294,000
Efficiency
Smoke Density
Controls:
86% with #2 Fuel Oil/ Diesel
0-3 per ASTM D2156
On/ Off Switch
Pressure Switch
High Limit Switch
Fuel Solenoid:
Safety Relief:
Unit Net Weight (Lbs/kg):
Unit Shipping Weight (Lbs/kg):
Unit Net Dimension (In/cm):
Unit Shipping Dimension (In/cm):
©
Copyright 1999, Mi-T-M Corporation
Industrial grade rocker switch
Shuts off burner fuel supply upon trigger release
Shuts off burner fuel supply when outlet water temp. exceeds 210 F/ 99 C
12 Volt
Relieves excess system pressure
428/194
551/250
430/195
553/251
43L x 30W x 41H/109L x 76W x 104H
46.5L x 31.5W x 48.5H/118L x80W x123H
3
EX-9056-052199R1-1C
Issue Date: 102097
EMF SYSTEM
©
Copyright 1999, Mi-T-M Corporation
OMHSP046-072996-BAR
OMHSP045-042699-BAR
FLOW CHART
4
EX-9056-052199R1-1C
Issue Date: 102097
GENERAL THEORY OF OPERATION
WATER FLOW: Connect a pressurized water source to the INLET GARDEN HOSE CONNECTION (1) and turn on the water supply.
The water will flow through a WATER STRAINER (2) which has a clear inspection bowl.
The water then travels into the TRIPLEX HIGH PRESSURE PUMP (3) which has an UNLOADER (4) that bypasses the water when
the trigger gun is closed. To protect the pump from heated water during this bypass stage, a HEAT DUMP VALVE (5) will open at
140°F/60°C allowing the heated water to escape. The Heat Dump Valve automatically resets when the water cools. The PRESSURE SWITCH (6) controls the fuel supply to the burner.
When using detergents, the solution passes through the DETERGENT STRAINER (7) located on the DETERGENT HOSE (8). The
detergent solution then travels into the ADJUSTABLE LOW PRESSURE DETERGENT INJECTOR (9).
From there, the water may be allowed to flow out of the DRAIN PLUG (10) or through the HEAT EXCHANGER INLET (11) where it is
heated when the burner is on. As the water exits the HEAT EXCHANGER OUTLET (12), it enters a safety system which protects
the operator from danger. The safety system contains a HIGH TEMPERATURE LIMIT SWITCH (13) which senses the water temperature and shuts off the fuel supply to the burner if it gets too hot. If the unloader fails to by pass the water or the burner remains
on when the trigger gun is closed, the SAFETY RELIEF (14) will relieve and allow water to exit safely.
The heated water then flows through the HIGH PRESSURE HOSE (15) and to the TRIGGER GUN ASSEMBLY (16) which allows the
operator to control the water spray. When the trigger gun is open, the water flows through the ADJUSTABLE PRESSURE DUAL
LANCE (17) and exits the NOZZLE (18).
FUEL FLOW: The Fuel Pump draws fuel from the FUEL TANK (19) through a replaceable FUEL FILTER/WATER SEPARATOR (20)
and into the FUEL PUMP (21). Fuel exits the fuel pump, into a FUEL SOLENOID VALVE (22) which controls fuel flow to the FUEL
NOZZLE (23) where it ignites and burns in the heat exchanger.
EMF SYSTEM: The patent pending Electro Magnetic Firing (EMF) System is an integrated system which gives all the requirements
for combustion.
The BELT (1) from the power source turns the HUB (2) which has two EXTERIOR MAGNETS (3) attached. As these magnets spin
past the IGNITION MODULE (4), a magnetic flux is created from which the ignition module produces a high voltage. This voltage
arcs across the electrodes giving the spark that is needed for ignition.
This hub has an INTERNALLY MOUNTED MAGNET (5) which spins past a STATOR (6) that produces the voltage that controls the
fuel supply to the heat exchanger. In addition to this, the hub also spins the BLOWER FAN (7) that forces the air into and through
the heat exchanger.
The FUEL PUMP (8) is also connected the hub by means of a flexible coupler.
©
Copyright 1999, Mi-T-M Corporation
5
EX-9056-052199R1-1C
Issue Date: 102097
HSP-3504-1MGH/GV-031799-BAR
DECAL PLACEMENT
©
Copyright 1999, Mi-T-M Corporation
6
EX-9056-052199R1-1C
Issue Date: 102097
HSP-3504-1MGH/GV-031799-BAR
DECAL PLACEMENT
REF. #
©
Copyright 1999, Mi-T-M Corporation
DESCRIPTION
PART #
QTY.
1
Decal- Wa rni ng : Don’t Modify Plumbing (E/S)
34-0807
1
2
Decal- Clear Laminate
N/A
1
3
Decal- Data Plate
N/A
1
4
Serial Number
N/A
1
5
Decal- Wa rni ng : Hot Coil Exhaust (E/S)
34-0808
1
6
Decal- Allow to Cool (E/S)
34-0599
1
7
Decal- Hot Surface (E/S)
34-0598
1
8
Decal- Risk of Fire (E/S)
34-0806
1
9
Decal- Burner On/Off (E/S)
34-0849
1
10
Decal- Wa rni ng / Caution/ Operation (E/S)
34-0847
1
11
Decal- Stripe
34-0725
2
12
Decal-White Die Cut
34-0034
1
13
Decal- Stripe
34-0560
1
14
Plastic Mi-T-M Logo
62-0093
1
7
EX-9056-052199R1-1C
Issue Date: 102097
HSP105-031699-BAR
FRAME
©
Copyright 1999, Mi-T-M Corporation
8
EX-9056-052199R1-1C
Issue Date: 102097
HSP105A-031699-BAR
FRAME
©
REF. #
DESCRIPTION
1
Frame Assembly
2
QTY.
REF. #
PART #
QTY.
5-0120A01
1
17
Engine/Pump Assembly (See exploded drawing)
N/A Sep.
1
Wheel
14-0006
4
18
Shim
33-0169
4
3
Jam Nut
30-0117
4
19
Electric Box Assembly (See exploded drawing)
N/A Sep.
1
4
Bolt
27-9524
12
20
Wire Tie
33-0022
4
5
Flatwasher
28-0022
8
21
Fuel Hose Assembly
15-0165
1
6
High Pressure Hose Assembly
15-0202
1
22
Heat Exchanger/ EMF Assembly (See exploded drawing)
N/A Sep.
1
7
Bolt
27-9529
6
23
Hood Assembly
850-0194
1
8
Unloader/Manifold Assembly (See exploded drawing)
N/A Sep.
1
24
Hand Knob
62-0057
1
9
Hose Clamp
42-0011
2
25
Trim Lock *(One Foot Required)
33-0129
1
10
Hose
15-0007
2
26
Screw Connect
17-0035
1
11
Hex Nut
30-3023
8
27
Hose Assembly
15-0166
1
12
High Pressure Hose Assembly
15-0194
1
28
Gun/Lance Assembly
850-0181
1
13
Fuel Tank Assembly (Includes 14, 15)
850-0248
1
29
Dual Lance Assembly
850-0180
1
14
Hex Head Plug
23-0296
1
30
Nozzle- 1503.5
18-0254
1
15
Fuel Cap
12-0033
1
31
Nozzle- 4060
18-0110
1
16
Fuel Hose
15-0147
2
Copyright 1999, Mi-T-M Corporation
PART #
DESCRIPTION
*Must Order in One Foot Lengths
9
EX-9056-052199R1-1C
Issue Date: 102097
HPS106-031699-BAR
ENGINE/PUMP ASSEMBLY
©
Copyright 1999, Mi-T-M Corporation
10
EX-9056-052199R1-1C
Issue Date: 102097
HSP106A-031699-BAR
ENGINE/PUMP ASSEMBLY
REF #
©
DESCRIPTION
PART #
QTY
1MGH
QTY
1MGV
REF #
DESCRIPTION
PART #
QTY
1MGH
QTY
1MGV
1
Hose Gasket
26-0001
1
1
23
Elbow
23-0242
1
1
2
Hose Swivel
23-0095
1
1
24
High Pressure Hose Assembly
15-0194
1
1
3
Strainer Complete (Includes 4-7)
19-0096
1
1
25
Key- Honda
43-0088
1
-
4
Strainer Bowl
19-0103
1
1
-
Key- Vanguard
43-0089
-
1
5
Stainless Steel Screen
19-0104
1
1
26
Oil Drain Plug w/Engine
N/A
1
1
6
Strainer Gasket
25-0056
1
1
27
Washer- Honda
28-0605
2
-
7
Strainer Body
19-0105
1
1
-
Washer- Vanguard
28-0606
-
2
8
Elbow
23-0119
1
1
28
Oil Drain Port- Honda
24-0143
1
-
9
Hose Clamp
42-0011
1
1
-
Oil Drain Port- Vanguard
24-0142
-
1
10
High Pressure Hose
15-0007
2
2
29
Screw- Honda
27-8880
3
-
11
Pump
3-0144
1
1
-
Screw- Vanguard
27-3093
-
3
12
Bolt Kit
70-0170
1
1
30
Muffler Deflector- Honda
45-0055
1
-
13
Belt
11-0037
1
1
-
Muffler Deflector- Vanguard
45-0054
-
1
14
Sheave
10-0077
1
1
31
Engine- 13 H.P. Honda
1-0086
1
-
15
Set Screw
27-8895
4
4
-
Engine- 13 H.P. Vanguard
1-0090
-
1
16
Bolt
27-0418
4
4
32
Washer- Honda
28-1029
1
-
17
Flange Pump
38-0049
1
1
-
Washer- Vanguard
28-0005
-
1
18
Bolt
27-9526
4
4
33
Lockwasher- Honda
29-0008
1
-
19
Beltguard
20-0384A01
1
1
-
Lockwasher- Vanguard
29-0009
-
1
20
Plug
23-0244
1
1
34
Bolt- Honda
27-0141
1
-
21
Pressure Switch
850-0173
1
1
-
Bolt- Vanguard
27-0190
-
1
22
Thermo Valve
22-0114
1
1
Copyright 1999, Mi-T-M Corporation
11
EX-9056-052199R1-1C
Issue Date: 102097
OMPMP024-051297-BAR
HIGH PRESSURE PUMP (3-0144)
©
Copyright 1999, Mi-T-M Corporation
12
EX-9056-052199R1-1C
Issue Date: 102097
0MPMP024-051297-BAR
HIGH PRESSURE PUMP (3-0144)
REF. #
©
DESCRIPTION
PART #
QTY.
REF. #
DESCRIPTION
PART #
QTY.
REF. #
DESCRIPTION
PART #
QTY.
1
Bolt
27-8380
4
20
Bolt
27-8381
4
39
Spacer (See 70-0173)
N/A Sep.
3
2
Washer
26-0159
4
21
Gasket
26-0139
1
40
Spring (See 70-0173)
N/A Sep.
3
3
Oil Seal
46-0538
1
22
Oil Sight Gauge
22-0123
1
41
Washer (See 70-0173)
N/A Sep.
3
4
Bearing Case
46-0498
1
23
Piston Pin
46-0502
3
42
Slotted Nut
46-0317
3
5
O-ring
25-0298
1
24
Piston Rod
46-0688
3
43
O-ring
25-0297
6
6
Washer
46-0499
1
25
Seal Washer
46-0484
3
44
Back-up Ring
25-0294
6
7
Bearing
46-0500
1
26
Oil Seal
46-0485
3
45
Spacer Adapter
46-0510
3
8
Crankshaft
46-0687
1
27
Washer
46-0689
3
46
Valve Assembly (Includes 47-50) (See 70-0174)
N/A Sep.
3
9
Connecting Rod
46-0521
3
28
Backup Ring
25-0378
3
47
Valve Seat (See 70-0174)
N/A Sep.
3
10
Crankcase
46-0497
1
29
Spacer Adapter
25-0377
3
48
Valve (See 70-0174)
N/A Sep.
3
11
Oil Fill Cap
46-0523
1
30
Sleave
46-0690
3
49
Spring (See 70-0174)
N/A Sep.
3
12
O-ring
25-0199
2
31
Seal Retainer
46-0504
3
50
Valve Cage (See 70-0174)
N/A Sep.
3
13
Washer (See 70-0170)
N/A Sep.
4
32
Low Pressure Seal (See 70-0172)
N/A Sep.
3
51
Outlet Manifold
46-0511
1
14
Lockwasher (See 70-0170)
N/A Sep.
4
33
Inlet Manifold
46-0506
1
52
Cap Screw
46-0533
8
15
Bolt (See 70-0170)
N/A Sep.
4
34
Plunger
46-0528
3
53
Set Screw
27-8895
2
16
Oil Drain Plug
39-0057
1
35
Adapter- Female
46-0508
3
Bolt Mounting Kit (Includes 4 each 3-15)
70-0170
17
Bearing
46-0501
1
36
V-packing (See 70-0172)
N/A Sep.
6
Seal Kit (Includes 3 each 32, 36-37, 43)
70-0172
18
O-ring
25-0293
1
37
Cotterpin
43-0064
3
Inlet Valve Kit (Includes 3 each 37-41, 43)
70-0173
19
Cover
46-0525
1
38
Inlet Valve (See 70-0173)
N/A Sep.
3
Valve Kit (Includes 3 each 43, 44, 47-50)
70-0174
Copyright 1999, Mi-T-M Corporation
13
EX-9056-052199R1-1C
Issue Date: 102097
Fig. A
Fig. B
PUMP SERVICE GUIDE
DISASSEMBLY OF THE DISCHARGE VALVE ASSEMBLY
1. Disconnect all plumbing for ease in servicing.
2. Inspect oil for proper level, presence of water or discoloration and replace as needed.
3. With a standard M6 allen wrench remove the eight (8) socket head screws from the manifold. Remove the
outer screws first, then the center screws.
4. With a soft mallet tap the back side of the Discharge Manifold from alternate sides to maintain alignment and
avoid damage to the plungers (Fig. A).
5. Grasp the Discharge Manifold from the underside and gradually lift manifold while you pull away from the
crankcase.
6. The Discharge Valve Spacers may stay with either the discharge or inlet manifold. By inserting two opposing
screwdrivers between spacer and manifold you can easily pry them out of the discharge manifold (Fig. B). If
they stay in the inlet manifold, gently work them up and down as you pull away from the inlet manifold (Fig. C).
7. The valve assemblies are in the discharge manifold ports and will fall out when manifold is turned over.
A complete valve assembly includes: retainer, spring, valve and seat (Fig. D).
DISASSEMBLY OF THE SEAL ASSEMBLY
Fig. C
Fig. D
©
Copyright 1999, Mi-T-M Corporation
1. Next remove the Inlet Valve Assembly from the exposed plunger rod ends. Including: cotterpin, nut, washer,
spring, spacer and inlet valve (Fig. E).
2. Grasp the Inlet Manifold from the front and underside and pull to remove from plunger rods (Fig. F).
3. Carefully examine back side of Lo-Pressure Seal before removing from manifold as it will be damaged during
removal. If worn, insert screwdriver into I.D. of seal and pry out. Exercise caution to avoid damage to the inlet
manifold (Fig. G).
4. Next press the ceramic Plunger with a thumb or soft tool from the back side of inlet manifold. The
V-Packing and adapters may stay with the plungers or remain in the inlet manifold. If on the plungers, slide off
by hand. If in the manifold, use a reverse pliers to remove.
5. Then remove Seal Retainers from crankcase by grasping tab with pliers and pulling out the high and low
pressure sections (Fig. H).
6. Examine crankcase oil seal to determine if crankcase servicing is needed.
Fig. E
Fig. F
14
Fig. G
Fig. H
EX-9056-052199R1-1C
Issue Date: 102097
REASSEMBLY OF SEAL ASSEMBLY
Fig. I
1. Examine Seal Retainers and replace if worn or damaged. Install on Plunger Rod and press into crankcase
with tab out.
2. Place Inlet Manifold on work surface with small I.D. ports up.
3. Lubricate new Lo-Pressure Seal and press into position with garter spring down. Be certain the seal is seated
squarely on the shoulder on the inlet manifold chamber (Fig. I).
4. Place Inlet Manifold on work surface with larger I.D. ports up.
5. Place new Female Adapter into inlet manifold chamber with v-groove facing up.
6. Carefully examine the plungers for scoring or cracks and replace if worn.
7. Lubricate ceramic Plungers and new V-Packings. Press the plunger into the V-Packings and position seal in
middle of plunger (Fig. J).
Fig. J
NOTE:
The deeper recessed end of the plunger should face the same direction as the v-groove on the
V-Packing (Fig. K).
8. Insert the Plungers into the manifold ports with v-groove facing up. Press into position using the larger I.D.
end of Discharge Valve Spacer.
9. Carefully install Inlet Manifold over Plunger Rod ends and slowly press into crankcase.
10. Examine Inlet Valve and replace if worn. Inlet Valve cannot be lapped or reversed if worn. Install nylon Inlet
Valve with ridged side towards the discharge. Stainless steel valves with square edges towards the
plungers (round edges towards the discharge).
11. Examine Spacers for wear and replace as needed. Install Spacer on each plunger rod with smaller O.D.
towards inlet valve.
12. Examine Springs for damage or fatigue and replace as needed. Place on plunger rods.
13. Install washer next with concave side towards inlet manifold.
14. Next install nuts and torque to 4.4 Ft/lbs (53 in/lbs).
15. Always install new cotterpins and turn ends to secure in position.
Fig. K
REASSEMBLY OF THE DISCHARGE VALVE ASSEMBLY
Fig. L
©
5
1
3
8
4
2
Copyright 1999, Mi-T-M Corporation
7
6
1. Examine Discharge Valve Spacer O-rings and replace if worn. Lubricate and install o-rings and back-up rings
on both front and rear of Discharge Valve Spacer.
2. Install Valve Retainers into each Discharge Manifold port with tab down.
3. Replace worn or damaged Springs and place into Retainers.
4. Examine Valve and Seats for pitting, grooves or wear and replace as needed.
5. Place Valves over Springs with concave side down.
6. Place Valve Seats on Valves with smaller I.D. down.
7. Lubricate O.D. of Discharge Valve Spacer and insert smaller I.D. into discharge manifold ports. Snap into
position.
8. Carefully guide Discharge Manifold with Spacer over Plunger Rod ends and press into Inlet Manifold.
9. Replace cap screws and torque to 9.4 Ft/lbs (113 in/lbs). Torque diagonally in order shown (Fig. L).
10. If oil was not changed, be certain oil is to mark on oil gauge before resuming operation.
15
EX-9056-052199R1-1C
Issue Date: 102097
OMHSP080-120498-BAR
UNLOADER/MANIFOLD ASSEMBLY
©
Copyright 1999, Mi-T-M Corporation
16
EX-9056-052199R1-1C
Issue Date: 102097
OMHSP080-120498-BAR
UNLOADER/MANIFOLD ASSEMBLY
REF. #
DESCRIPTION
PART #
QTY.
1
Hose *(Two Feet Required)
15-0007
1
2
Hose Clamp
42-0011
1
3
Elbow
23-0119
1
4
Unloader Assembly
850-0252
1
5
Plug
23-0238
1
6
Detergent Injector
50-0052
1
7
Manifold Block
51-0026
1
8
High Pressure Hose Assembly
15-0202
1
9
Detergent Strainer
19-0050
1
10
Detergent Hose *(Six feet Required)
15-0021
1
11
High Pressure Hose Assembly
15-0194
1
*Must Order in One Foot Lengths
©
Copyright 1999, Mi-T-M Corporation
17
EX-9056-052199R1-1C
Issue Date: 102097
UNLOADER (850-0252)
OMGEN163-101298-BAR
UNLOADER (850-0252)
OMGEN163-101298-BAR
REF. #
DESCRIPTION
Copyright 1999, Mi-T-M Corporation
18
QTY.
1
Hex Nut
8-0362
2
2
Cover
7-0098
1
3
Set Screw
27-4280
1
4
Adjusting Insert- Brass
8-0363
1
5
Adjustment Nut
8-0364
1
6
Set Screw
8-0365
1
7
Glide Ring
8-0366
1
8
Spring
49-0104
1
9
Hex Nut
8-0367
1
10
Bushing
8-0368
1
11
Unloader Body
8-0369
1
12
Retainer
8-0269
1
13
Valve Housing
8-0104
1
14
Spring
49-0023
1
15
Valve
8-0105
1
16
O-ring
25-0036
1
17
Cylinder Pin
8-0372
1
18
Piston Repair Kit
70-0243
1
19
Spacer
8-0371
1
20
Stop Nut
8-0157
1
21
Washer
29-0154
2
Check Valve Repair Kit (Includes 13-16)
70-0244
Unloader Complete
©
PART #
850-0252
EX-9056-052199R1-1C
Issue Date: 102097
PRESSURE SETTING & TROUBLESHOOTING THE UNLOADER
TOOLS NEEDED:
5000 PSI gauge
2.5mm Allen Wrench
Small Flathead Screw Driver
Adjustable Wrench
TO SET MAXIMUM SPRAY PRESSURE AND BYPASS PRESSURE:
Refer to Parts Listing on pg.18. Install the test gauge in the auxiliary port on unloader or in discharge line after the unloader valve. With the pump operating but the
trigger gun off, loosen the SET SCREW (3) and remove the COVER (2). Remove both HEX NUTS (1) and set aside. Using the 2.5 mm Allen wrench, loosen the SET
SCREW (6) and turn the ADJUSTING NUT (5) with adjustable wrench counterclockwise so that it is flush with top of the ADJUSTING INSERT (4). Tighten the SET
SCREW (6). With adjustable wrench, turn the ADJUSTING NUT (5) clockwise until the ADJUSTING INSERT (4) bottoms out against the HEX NUT (9). Loosen the
SET SCREW (6) with 2.5 mm Allen wrench, so that the ADJUSTING NUT (5) turns freely but does not turn the ADJUSTING INSERT (4). With proper nozzle installed
in spray gun, squeeze trigger and turn ADJUSTING NUT (5) clockwise to desired maximum spray pressure. Then tighten the SET SCREW (6) securely and release
the trigger on the trigger gun. Squeeze and release trigger several times to verify consistency of spray pressure setting. Turn the ADJUSTMENT NUT (5) counterclockwise two full turns and then clockwise again until tight. Squeeze trigger and verify desired pressure setting. Spray pressure should fall within 5% of original
setting. Bypass pressure (the reading on the gauge when the trigger is released) should exceed the spay pressure by approximately 15-20%. If valve fails to repeat
within specifications, repeat the steps above and assure all final settings are tight. Install one HEX NUT (1) and tighten against the ADJUSTING INSERT (4). Install the
second HEX NUT (1) and tighten securely against the first. Insert the COVER (2) and tighten the SET SCREW (3).
TROUBLESHOOTING:
SYSTEM WILL NOT COME UP TO FULL DESIGNATED PRESSURE:
*
*
*
*
Spray nozzle worn or nozzle orifice is too large in relation to pump flow rate.
Adjusted improperly. Refer to pressure adjustment section for proper procedures.
Bypass valve (within unloader) is obstructed or leaking. Remove and clean bypass cartridge or replace. Replace with #850-0252.
Flow rate of pump inadequate. Assure designated flow rate of pump is adequate in relation to spray nozzle size.
PRESSURE SPIKES IN DISCHARGE LINE DURING BYPASS MODE:
*
Pressure adjustment too tight. Refer to pressure adjustment section for proper adjustment procedures.
UNLOADER CYCLES WHILE IN BYPASS MODE:
*
*
©
External leak on unloader or in downstream fittings. Inspect all high pressure lines (including gun and hose) for any signs of leakage and
repair as necessary.
Non-return valve. (within the unloader) damaged, obstructed or worn. Inspect and replace as necessary. Replace with #70-0244.
Copyright 1999, Mi-T-M Corporation
19
EX-9056-052199R1-1C
Issue Date: 102097
PRESSURE SWITCH (850-0173)
850-0173-051497-BAR
PRESSURE SWITCH (850-0173)
850-0173-051497-BAR
REF #
DESCRIPTION
1
Pressure Switch Complete (Inc. 2-20)
2
Copyright 1999, Mi-T-M Corporation
20
QTY
850-0173
1
Screw
N/A
4
3
Cover
N/A
1
4
O-ring
N/A
1
5
Micro Switch
N/A
1
6
Hex Nut
N/A
2
7
Screw
N/A
2
8
Housing
N/A
1
9
O-ring
N/A
1
10
Bushing Nut
N/A
1
11
Wire Assembly
N/A
1
12
O-ring
N/A
1
13
Spring Housing
N/A
1
14
O-ring (See 70-0007)
N/A Sep.
1
15
Washer Spacer
28-0218
2
16
Spring
49-0107
1
17
Piston
N/A
1
18
Back-up Ring (See 70-0007)
N/A Sep.
2
19
O-ring (See 70-0007)
N/A Sep.
1
20
Hex Nipple
N/A
1
O-ring Kit (1 each 14, 18-19)
©
PART #
70-0007
EX-9056-052199R1-1C
Issue Date: 102097
DETERGENT INJECTOR (50-0052)
OMGEN284-052898-DCE
DETERGENT INJECTOR (50-0052)
REF. #
DESCRIPTION
1
Orifice (2.1mm)
2
Injector Body
3
PART #
QTY.
50-0057
1
N/A
1
Spring (See 852-0056)
N/A Sep.
1
4
Ball (See 852-0056)
N/A Sep.
1
5
O-ring (See 852-0056)
N/A Sep.
1
6
Piston Retainer
50-0156
1
7
Spring
49-0056
1
8
O-ring (See 852-0056)
N/A Sep.
1
9
Adjustable Shutter Barb
50-0157
1
10
Adjustment Knob
50-0158
1
Injector Repair Kit (Includes 3-5, 8)
852-0056
COIL DRAIN PLUG (850-0218)
850-0218-041597-BAR
COIL DRAIN PLUG (850-0218)
REF. #
©
Copyright 1999, Mi-T-M Corporation
21
DESCRIPTION
PART #
QTY.
1
Bolt
27-9526
1
2
Retaining Cable
33-0260
1
3
Snap Ring
33-0261
1
4
Hand Wheel
16-0239
1
5
Plug
24-0147
1
6
Back-up Ring
25-0424
1
7
O-ring
25-0423
1
EX-9056-052199R1-1C
Issue Date: 102097
HSP083-120498-BAR
HEAT EXCHANGER/EMF SYSTEM
©
Copyright 1999, Mi-T-M Corporation
22
EX-9056-052199R1-1C
Issue Date: 102097
OMHSP083-120498-BAR
HEAT EXCHANGER/EMF SYSTEM
REF. #
©
DESCRIPTION
PART #
QTY.
REF. #
DESCRIPTION
1
Boiler Assembly Complete
850-0226
1
23
Pin
2
EMF Assembly
850-0257
1
24
3
Hex Nut
30-3022
2
4
Fuel Pump Coupler
33-0225
5
Nut
6
PART #
QTY.
33-0211
1
Tensioner Sheave Shaft Assembly (Inc. 5, 25, 26)
850-0166
1
25
Sheave Assembly
850-0177
1
1
26
Shaft
33-0212
1
30-0159
2
27
Access Panel- Black
20-0386A01
1
Flatwasher
28-0022
1
28
Bolt
27-9526
2
7
Tensioner Base
10-0071
1
29
Grommet
32-0426
1
8
Fuel Pump Bracket- Black
20-0381A01
1
30
Gromment
32-0427
1
9
Bolt
27-9524
7
31
Elbow
23-0287
1
10
Hex Nut
30-3023
8
32
High Limit Switch
32-0423
1
11
Fuel Hose Assembly
15-0165
1
33
Outlet Connector Block
24-0138
1
12
Elbow
23-0288
1
34
Pressure Relief Valve
22-0273
1
13
Fuel Solenoid- 12 Volt
44-0100
1
35
Adapter
23-0369
1
14
Fuel Pump
3-0020
1
36
Nipple
24-0141
1
15
Elbow
23-0237
2
37
Hex Reducer
23-0197
1
16
Fuel Hose
15-0147
2
38
High Pressure Hose Assembly
15-0202
1
17
Hex Nipple
24-0145
1
39
Street Tee
23-0058
1
18
Filter Fuel Water Seperator
19-0070
1
40
Nipple
24-0165
1
19
Fuel Water Seperator Replacement Bowl
19-0071
1
41
Elbow
23-0306
1
20
Fuel Water Seperator Replacement Filter
19-0053
1
42
Adapter
23-0279
1
21
Plate- Black
20-0363A01
1
43
Drain Plug Assembly
850-0218
1
22
Bracket- Black
20-0360A01
2
Copyright 1999, Mi-T-M Corporation
23
EX-9056-052199R1-1C
Issue Date: 102097
BOILER ASSEMBLY (850-0226)
850-0226-112097-BAR
HSP111-042799-BAR
ELECTRODE GAP SETTINGS
©
Copyright 1999, Mi-T-M Corporation
24
EX-9056-052199R1-1C
Issue Date: 102097
850-0226-112097-BAR
BOILER ASSEMBLY (850-0226)
REF. #
©
DESCRIPTION
PART #
QTY.
REF. #
DESCRIPTION
PART #
QTY.
1
Hex Nut
30-0121
2
15
Acorn Nut
30-6002
4
2
Plug
24-0034
1
16
Cone
20-0373
1
3
Heat Exchanger Outer Wrap- Black
20-0376A01
1
17
Nut
30-6001
3
4
Bolt
27-8879
2
18
Fuel Nozzle
18-0308
1
5
Air Diverter Plate- Black
20-0378A01
1
19
Electrode Plate
38-0046
1
6
Air Diverter Stem Assembly- Black
20-0377A01
1
20
Electrode
32-0420
2
7
Lockwasher
28-1009
4
21
O-ring
25-0171
2
8
Hex Nut
30-0137
1
22
Bolt
27-9526
5
9
Bottom Insulation
33-0250
1
23
Electrode Mounting Clip- Black
20-0383A01
2
10
Washer
28-0521
2
24
Bolt
27-8878
4
11
Heat Exchanger Coil Assembly
66-0011
1
25
Nozzle Holder
23-0292
1
12
Inner Pan Assembly
20-0372
1
26
Snap Ring
33-0254
1
13
Top Pan Assembly- Black
20-0371A01
1
27
Sight Glass
33-0252
1
14
Lockwasher
28-1028
4
Copyright 1999, Mi-T-M Corporation
25
EX-9056-052199R1-1C
Issue Date: 102097
HSP051-051597-JTR
GUN (850-0181) & ADJUSTABLE PRESSURE DUAL LANCE (850-0180)
©
Copyright 1999, Mi-T-M Corporation
26
EX-9056-052199R1-1C
Issue Date: 102097
OMHSP051a-051597-JTR
GUN (850-0181) & ADJUSTABLE PRESSURE DUAL LANCE (850-0180)
REF. #
©
DESCRIPTION
PART #
QTY.
REF. #
DESCRIPTION
PART #
QTY.
850-0181
1
24
Handle
16-0313
1
1
Gun/Lance Assembly (Includes 2-20)
2
Pipe Assembly
16-0016
1
25
Washer
28-1021
1
3
Plastic Housing
16-0008
1
26
Nut
30-3010
1
4
Screw
27-3230
2
27
Adaptor
23-0271
1
5
Housing
16-0012
1
28
O-ring
25-0351
1
6
Gun Repair Kit
70-0055
1
29
Piston
16-0314
1
7
Plug
39-0024
1
30
Back-up Ring
25-0352
1
8
Cover
16-0009
1
31
O-ring
25-0353
1
9
Trigger Safety Lock-off
16-0010
1
32
Upper Protector
16-0315
1
10
Trigger Pin
16-0063
1
33
Screw
27-8862
1
11
Pipe Assembly
16-0013
1
34
Lower Protector
16-0316
1
12
Adaptor
16-0283
1
35
Body
23-0272
1
13
Pipe
16-0277
1
36
Lance w/Protective Cover
16-0317
2
14
Guard Lance (Right Side)
16-0320
1
37
Nut
30-3060
2
15
Screw
27-8382
6
38
Pipe Clamp
16-0318
2
16
Guard Lance (Left Side)
16-0321
1
39
Screw
27-8861
2
17
Plug
39-0076
1
40
Nipple
24-0127
2
18
Screw
49-0103
1
41
Nozzle Protector
16-0319
1
19
Spacer
16-0282
1
42
Nozzle-6540
18-0110
1
20
Lance Holder (See 16-0306)
N/A Sep.
1
Gun Assembly ( Includes 12-20)
16-0001
21
Dual Lance Assembly (Includes 22-42)
850-0180
1
Lance Assembly (Includes 13-21)
16-0306
22
Handle Plug
16-0312
1
O-ring Kit (Includes 28, 30, 31)
70-0143
23
Nut
30-3002
1
Copyright 1999, Mi-T-M Corporation
27
EX-9056-052199R1-1C
Issue Date: 102097
FUEL TANK (850-0248)
850-0193A-012098-BAR
FUEL TANK (850-0248)
850-0193-012098-BAR
REF. #
©
Copyright 1999, Mi-T-M Corporation
28
DESCRIPTION
PART #
QTY.
1
Plug
23-0296
1
2
Fuel Tank (See 850-0193)
N/A Sep.
1
3
Elbow
23-0237
1
4
Decal-Warning: Risk of Fire (E/S)
34-0806
1
5
Flare
23-0247
1
6
Fuel Pick-up Line
33-0270
1
7
Bushing
33-0255
1
8
Fuel Indicator Gauge
22-0215
1
9
Fuel Cap-Vented
12-0033
1
EX-9056-052199R1-1C
Issue Date: 102097
FUEL PUMP (3-0020) & FUEL SOLENOID (44-0100)
0MHSP049/071796/BAR
FUEL PUMP (3-0020) & FUEL SOLENOID (44-0100)
OMHSP049-071796-BAR
REF. #
©
Copyright 1999, Mi-T-M Corporation
29
DESCRIPTION
PART #
QTY.
1
Cord-Din Connector
46-1017
1
2
Base Plate
46-1014
1
3
Nut
46-1016
1
4
Solenoid Coil- 12 Volt
46-1015
1
5
Screw
N/A
2
6
Piston
46-1012
1
7
Bolt
46-1009
1
8
Washer
26-0150
2
9
Solenoid Body
N/A
1
10
Plug
24-0082
1
11
Fuel Pump Body
N/A
1
12
Cover Gasket
26-0109
1
13
Fuel Oil Strainer
19-0034
1
14
Fuel Pump Cover
46-1005
1
15
Fuel Pump Cover Screw
46-1006
4
EX-9056-052199R1-1C
Issue Date: 102097
OMHSP072-102698-BAR
EMF SYSTEM (850-0257)
©
Copyright 1999, Mi-T-M Corporation
30
EX-9056-052199R1-1C
Issue Date: 102097
OMHSP072A-102698-BAR
EMF SYSTEM (850-0257)
REF. #
©
Copyright 1999, Mi-T-M Corporation
DESCRIPTION
PART #
QTY.
1
EMF Assembly (Includes 2-17)
850-0257
1
2
Blower Flange Assembly (Includes 3-6)
850-0258
1
3
Bearing
48-0041
2
4
Flange Blower
38-0040
1
5
Spacer
33-0206
1
6
Shaft- Blower
20-0347
1
7
Woodruff Key
43-0080
2
8
Cable Clamp
32-0403
1
9
Screw
27-2070
1
10
Stator Coil
850-0201
1
11
Screw
27-0740
4
12
Flange Magnet Hub
38-0041
1
13
Hex Nut
30-0177
2
14
Flatwasher
28-0010
2
15
Ignition Coil Assembly
850-0191
1
16
Blower Fan
44-0099
1
17
Screw Set w/ Fan
30-3021
1
31
EX-9056-052199R1-1C
Issue Date: 102097
OMHSP082-120498-BAR
ELECTRIC BOX
©
Copyright 1999, Mi-T-M Corporation
32
EX-9056-052199R1-1C
Issue Date: 102097
OMHSP082-120498-BAR
ELECTRIC BOX
©
Copyright 1999, Mi-T-M Corporation
REF. #
DESCRIPTION
PART #
QTY.
1
Switch/ Rocker
32-0422
1
2
Bolt
27-8881
4
3
Bolt and Gasket Kit
70-0169
1
4
Electric Box Lid- Black
32-0430A01
1
5
Terminal Strip
32-0394
1
6
Hex Nut
30-0152
4
7
Electric Box- Black
32-0429A01
1
8
Electrical Connecter
32-0085
1
9
Electric Box Bracket- Black
20-0380A01
1
33
EX-9056-052199R1-1C
Issue Date: 102097
OMHSP050A-051697-BAR
WIRING SCHEMATIC
©
Copyright 1999, Mi-T-M Corporation
34
EX-9056-052199R1-1C
Issue Date: 102097
OMHSP050B-051697-BAR
WIRING DIAGRAM
©
Copyright 1999, Mi-T-M Corporation
35
EX-9056-052199R1-1C
Issue Date: 102097
©
Copyright 1999, Mi-T-M Corporation
36
EX-9056-052199R1-1C
Issue Date: 102097
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement