Midland BR777 Owner`s manual

Midland BR777 Owner`s manual
BR777
TWO-WAY RADIO
OWNER'S MANUAL
www.bluestarcomm.net
Model BR777
TABLE OF CONTENTS
1
Introduction
Important Notice, FCC Licensing
LCD Display
Controls
Battery Installation
Installing the Belt Clip
Installing the Swivel Holster
Charging the Battery Pack
Charging thru the Multi-Unit Charger
Battery Level Indicator
Operating Your Radio
Factory Default Setting
Programming your Radio Settings
Keypad Lock
External Speaker/Microphone Jack
Troubleshooting Guide
Use and Care
Specifications and Frequency Charts
Warranty Information
Accessories
2
3
4
5
6
7
7
8
9
9
10 - 11
12
13 - 16
17
17
18
18
19 - 21
22
23 - 24
Page 1
www.bluestarcomm.net
Model BR777
Welcome to the world of Midland electronics
Congratulations on your purchase of a high quality MIDLAND product.
Your 2-way radio represents the state-of-the-art in high-tech
engineering. Designed for Business Radio operation, this compact
package is big in performance. It is a quality piece of electronic
equipment, skillfully constructed with the finest components. The
circuitry is all solid-state and mounted on a rugged printed circuit
board. Your two-way radio is designed for reliable and trouble-free
performance for years to come.
Features
- 4 Selectable Channels
- 56 Programmable Frequencies
- 121 Privacy Codes
- VOX
- CALL Alert Function
- VIBRATE Alert Function
- SCAN Function
- Cloning Capability
- Auto-Squelch Function
- Key Pad Lock
- Speaker / Microphone Jack
- Battery Meter / Battery Low Indicator
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions : (1) this device does not cause harmful interference, and
(2) this radio must accept any interference that may cause undesired operation.
To maintain compliance with FCC’s RF exposure guidelines, for body-worn
operation, this radio has been tested and meets the FCC RF exposure guidelines
when used with Midland Radio Corp. accessories supplied or designated for this
product. Use of other accessories may not ensure compliance with FCC RF
exposure guidelines. (Tested with Headset Model: AVP-1)
Page 2
www.bluestarcomm.net
Model BR777
IMPORTANT NOTICE FCC LICENSE REQUIRED FOR BUSINESS RADIO
OPERATION
The BR777 operates on UHF frequencies which require an FCC (Federal
Communications Commission) license. You must be licensed prior to operating
on these frequencies. Serious penalties could result for unlicensed use of these
frequencies, in violation of FCC rules, as stipulated in the Communications Act's
Sections 501 and 502 (amended).
You will be issued a call sign by the FCC which should be used for station
identification when operating the radio on these channels. You should also
cooperate by engaging in permissible transmissions only, avoiding channel
interference with other users, and being prudent with the length of their
transmission time.
To obtain a license or ask questions about the license application, contact the
FCC at 1-888-CALL FCC or go to the FCC's website:
http://www.fcc.gov and request form 601.
Exposure To Radio Frequency Energy
Your Midland radio is designed to comply with the following national and
international standards and guidelines regarding exposure of human being to radio
frequency electromagnetic energy:
- United States Federal Communications Commission, Code of Federal
Regulations: 47 CFR part 2 sub-part J
- American National Standards Institute (ANSI)/Institute of Electrical &
Electronic Engineers (IEEE) C95. 1-1992
- Institute of Electrical and Electronic Engineer (IEEE) C95. 1-1999 Edition
- National Council on Radiation Protection and Measurements (NCRP) of the
United States, Report 86, 1986
- International Commission on Non-lonizing Radiation Protection (ICNIRP)
1998
To control your exposure and ensure compliance with the general population or
uncontrolled environment exposure limits, transmit no more than 50% of the time.
The radio generates measurable RF energy exposure only when transmitting.
IMPORTANT: Changes or modifications to this unit not expressly approved by
MIDLAND RADIO CORP. and BLUE STAR could void your right to operate this
unit. Your radio is set up to transmit a regulated signal on an assigned frequency.
It is against the law to alter or adjust the settings inside the COMMUNICATOR to
exceed those limitations. Any adjustment to your radio must be made by qualified
technicians.
Page 3
www.bluestarcomm.net
Model BR777
LCD DISPLAY
1
7
2
8
3
9
4
10
5
11
6
12
1. BATTERY METER – Indicates the battery level.
2. KEY LOCK ICON – Indicates KEY LOCK mode is on.
3. RECEIVE (RX)/TRANSMIT (TX) ICON – Indicates radio is transmitting a
signal or receiving a transmission.
4. VOX ICON – Indicates when VOX mode is active.
5. CHANNEL NUMBER – Indicates the Channel (1~4) setting.
6. PRIVACY CODE – Indicates Privacy Code selected by user (oF~121).
7. VIBRATE-ALERT ICON – Indicates when the Vibrate-Alert feature is on.
8. TRANSMIT POWER LEVEL ICON – Indicates TX Power setting(Blank/Lo).
9. PROGRAM ICON – Indicates radio is in Programming mode.
10. CLONE ICON – Indicates radio is in Cloning mode.
11. PRIVACY CODE ICON – Indicates radio is in Privacy Code programming
mode.
12. FREQ CODE ICON – Indicates radio is in Frequency programming mode.
Page 4
www.bluestarcomm.net
Model BR777
CONTROLS
17
18
13
19
14
20
15
21
16
13. PTT Button – Press and hold to transmit voice communication.
14. UP Button – Increase the volume level or make adjustments in Program
mode.
15. DOWN Button – Decrease the volume level or make adjustments in
Program mode.
16. MIC – Built-in microphone.
17. ANTENNA.
18. EXTERNAL SPEAKER/MIC JACK.
19. SCAN/CALL/KEYLOCK Button – Press and hold within 2 seconds then
release to enter SCAN mode. Press twice quickly to send CALL Alert tone.
Press and hold to turn on/off the Keylock function.
20. MODE/POWER ON/OFF Button – Press and hold to turn the radio on/off.
Press to activate the MENU mode.
21. SPEAKER – Built-in speaker.
Page 5
www.bluestarcomm.net
Model BR777
BATTERY INSTALLATION
Your BR777 radio operates with 3.7Vdc 650mAh Li-ion Battery Pack
(BATT7L). The belt clip should be removed (see INSTALLING THE
BELT CLIP) to ease installation or removal of the batteries.
To install the batteries:
1. With the back of the radio facing you, remove the belt clip (see
INSTALLING THE BELT CLIP) for easy access, then remove the
Battery Cover by pressing down on the top center and sliding it
down from the radio.
2. Insert the Li-ion Battery Pack, observing the polarity as shown.
Installing the batteries incorrectly will prevent the unit from
operating or may damage the unit.
3. Return the Battery Cover by sliding it up on the radio. Replace the
belt clip.
Li-ion BATTERY
PACK
BATTERY
COMPARTMENT
IDE
T
ER
INS
S
HIS
HT
WIT
T
OU
BATTERY
COVER
Page 6
www.bluestarcomm.net
Model BR777
INSTALLING THE BELT CLIP
To install the BELT CLIP, use a screwdriver to attach the belt clip to
the radio. Turn the screwdriver clockwise to tighten the belt clip screw.
Turn the screwdriver counter-clockwise to loosen/remove the belt clip
screw.
INSTALLING THE SWIVEL HOLSTER
To install the SWIVEL HOLSTER (optional),
slide the radio (with the Belt Clip attached)
down into the slot on the Swivel Holster until
the HOLSTER LOCK TAB clicks. To remove
the SWIVEL HOLSTER, press the HOLSTER
LOCK TAB up, then gently pull the radio up
from the SWIVEL HOLSTER.
HOLSTER
LOCK TAB
SWIVEL
HOLSTER
Page 7
www.bluestarcomm.net
Model BR777
CHARGING THE BATTERY PACK
Your BR777 is equipped for using a rechargeable Li-ion Battery Pack
which can be recharged using a desktop charger (BRC501). Initial
charge time is 2 hours with a charge time of 2 hours thereafter. For
maximum battery life, we recommend charging the battery pack when
the low battery icon comes on.
To charge using a Desktop Charger (BRC501):
1. Turn off the unit.
2. Place the rechargeable battery packs in the radios.
3. Connect the AC adapter (18AD2) into an AC wall outlet.
4. Insert the AC adapter plug into the desktop charger jack.
5. Place the units into the desktop charger slot and note that the LED
indicator with RED color will light up, indicating charging function.
Once the battery packs are fully charged, the LED indicator will
change to GREEN color.
In order to ensure that the battery pack is fully charged, it is
recommended that the battery pack be charged with the radio
turned OFF.
!
1. Only use our Li-ion battery pack.
2. Do not attempt to charge any
battery packs other than the one
indicated in the manual. This
may cause leakage and damage
to the radio.
3. For long term storage of the
radio, turn the radio OFF and
remove the batteries
from the radio.
Page 8
www.bluestarcomm.net
Model BR777
CHARGING THRU THE MULTI-UNIT CHARGER
The BRC601 Multi-unit charger (not included) allows charging of up to
6 radios at the same time.
To charge using the Multi-unit Charger (BRC601):
1. Turn off the units.
2. Place the rechargeable battery packs in the radios.
3. Connect the AC adapter (18AD6) into an AC wall outlet.
4. Insert the AC adapter plug into the Multi-unit charger jack.
5. Place the units into the desktop charger slot and note that the LED
indicator with RED color will light up, indicating charging function.
Once the battery packs are fully charged, the LED indicator will
change to GREEN color.
Insert AC Adapter here
4.2Vdc 3A
RADIO CHARGING SLOT
BATTERY LEVEL INDICATOR
Your BR777 has a BATTERY LEVEL METER
that shows the
battery power level. The greater the number of bars visible, the
stronger the battery level. When the battery level is low, the Battery
Meter icon will display the Battery Shell
only; indicating your
Li-ion Battery Pack should be replaced or recharged. If the Li-ion
Battery Pack is not charged at this time, the radio will automatically
turn off after a few minutes to save the remaining battery energy.
Page 9
www.bluestarcomm.net
Model BR777
OPERATING YOUR RADIO
POWER ON/OFF
Press the MODE button for 3 seconds to turn the radio on. During
Power On, the radio will beep 2 times with different tones, the LCD will
display all icons for 1 second and the LCD display will indicate the last
channel selected.
To turn the radio off press the MODE button for 3 seconds.
TRANSMITTING AND RECEIVING A CALL
To communicate, all radios in your group must be set to the same
channel, frequency and Privacy Code.
1. For maximum clarity, hold the radio 2 to 3 inches from your mouth.
2. Press and hold the PTT button and speak in a normal voice
into the microphone. The TX icon will appear continuously on the
LCD Display while transmitting.
To transmit a CALL Alert Tone/Vibrate Alert, press the SCAN
button twice rapidly.
3. To receive a call, release the PTT button. The RX icon will appear
on the display when your radio is receiving a transmission.
RECEIVE SIGNAL STRENGTH INDICATOR
During receiving a transmission, the Signal Strength Indicator
number will appear on the right side of the LCD display. This meter is
on a scale of 1 to 4, with a “4” indicating a strong signal and a “1”
indicating a weak signal.
SETTING THE VOLUME LEVEL
To increase/decrease the Volume Level, press the S\T button during
standby or receiving mode. The LCD will display the current volume
setting.
CHANNEL SELECTION
Press the MODE button once, and then the S\T buttons to select
one of the 4 channels.
To confirm the selection, just wait for around 1 second until the FREQ
icon disappears and the CODE icon appears.
Page 10
www.bluestarcomm.net
Model BR777
TRANSMIT (TX) POWER LEVEL SELECTION
Your BR777 radio has 2 power level settings. To select the power
level on any channel, press and hold the PTT button, then press the
S button to select Hi Tx Power Level setting, or press the T button to
select Lo TX Power Level setting.
If you select blank on the TX Power setting icon, then the TX Power
will be set to to Hi Power.
If you select “Lo” on the TX power setting icon, the TX Power will be
set to Lo Power.
Note : When you press the PTT button while the Battery level is
low (shown by
), the TX Power setting will change automatically from Hi to Lo (if original setting is Hi)
You cannot change the TX Power setting when the radio is in
VOX mode.
!
SCAN
Your BR777 radio can scan all 4 channels for activity.
To enter the SCAN mode, press and hold the SCAN button for 2
seconds and release.
Your radio will rapidly scan each of the 4 channels and stop on any
active channel. Your radio will resume scanning after 4 seconds.
When you press the PTT button to transmit on an active channel, the
scanning function will stop and remain on the active channel for 5
seconds before resuming scan when the PTT button is no longer
pressed.
To exit the SCAN mode, quickly press the SCAN button while the radio
is scanning.cause low power conditions
l Be sure to set your radio to use Hi power.
Page 11
www.bluestarcomm.net
Model BR777
FACTORY DEFAULT SETTING
Your BR777 radio is programmed at the factory to the following
settings:
Channel
Frequency
1
2
2
8
3
5
4
6
Privacy Code
1
Scan List
y
Call Tone/
Vibrate Alert
0
VOX setting
0
To restore the factory settings:
Start with the radio powered off and press and hold the PTT button, S
and T button simultaneously while you power the radio on; done by
pressing the MODE button for 3 seconds or until an “EP” will be
displayed on the LCD.
Release the buttons.
Press the S button and a “CL” will appear next to the “EP”.
Press the MODE button again for around 3 seconds to turn the radio
off.
During this time, the radio will be set to the original factory setting.
Page 12
www.bluestarcomm.net
Model BR777
BR777 PROGRAMMING QUICK REFERENCE CHART
MODE
Channel
Frequency
Privacy
Scan List
Call Alert
VOX
1~4
1~56
0~121
y/n
0~4
0/1/2/3
Clone
1~3 is Call Alert
4 is Vibrate Alert
PROGRAMMING YOUR RADIO SETTINGS
Programming mode allows you to change the following settings on
your radio:
l Channel (1~4)
l Frequency (1~56)
l Privacy Code (0~121)
l Scan List (y/n)
l Call Alert/Vibrate Alert (0~4; 4 is for Vibrate Alert)
l VOX (0/1/2/3 ; 0 is off)
l Cloning
ENTERING THE PROGRAMMING MODE
To enter the PROGRAM mode, start with the radio powered off and
press and hold the SCAN button and PTT button simultaneously while
you power the radio on; done by pressing the MODE button for 3
seconds. The radio will beep and display all the LCD segments for a
few seconds. The Program icon (shown by PROG) will appear, the
channel number flashes, and the Frequency icon (shown by
FREQ) and Privacy Code icon (shown by CODE) will be displayed
alternately.
To exit PROGRAM mode, press the MODE button for 3 seconds then
the unit will power off.
Page 13
www.bluestarcomm.net
Model BR777
SELECTING A CHANNEL
In the PROGRAM mode, press the MODE button until the CHANNEL
icon flashes (this is the default setting when in Program mode).
Press the S\T button to select from the 4 available channel numbers.
Press the MODE button again to continue programming.
PROGRAMMING THE FREQUENCY
In the PROGRAM mode, press the MODE button until the FREQ icon
appears and the Frequency Code flashes.
Press the S\T button to select from the 56 available Frequency
numbers.
Press the MODE button again to continue programming.
PROGRAMMING THE PRIVACY CODES
Your BR777 has 121 Privacy Codes available. The selected Privacy
Code may be different for each channel.
In the PROGRAM mode, press the MODE button until the CODE icon
appears and the Privacy Code flashes.
Press the S\T button to select from the 121 available Privacy Code
numbers.
Press the MODE button again to continue programming.
!
Note : Selecting a Privacy Code of "0" will disable the Privacy
feature. To communicate between two BR777 radios, all radios
in your group must be set to the same Channel, Frequency and
Privacy Code selections.
Page 14
www.bluestarcomm.net
Model BR777
EDITING THE SCAN LIST
You can edit the SCAN List to skip channels during scanning.
In the PROGRAM mode, press the MODE button until the display
shows an “S” on the left side of the display and a “y” or “n” icon
flashing on the right of the channel number.
Press the S\T button to select “y” or “n”.
If you select “y” on any channel, it means it will be included on the
SCAN List.
If you select “n” on any channel, it means it will be excluded on the
SCAN List.
Press the MODE button again to continue programming.
PROGRAMMING CALL ALERT OR VIBRATE ALERT
Your BR777 radio has 3 selectable CALL Alert tones, so you can alert
the other radios that you need to communicate with them. Your radio
is programmed with the Call Alert turned off (set to 0), but you can
change this setting and choose among the 3 available tones.
Your BR777 radio also has a VIBRATE Alert function. This will enable
you to alert the other radios by vibration instead of a Call Alert sound
for a more silent operation.
Select Call Alert Tone 4 to turn the VIBRATE Alert on. The VIBRATE
Alert icon
will be displayed on the LCD when the VIBRATE Alert
function is on.
In the PROGRAM mode, press the MODE button until the CALL Alert
icon (shown as “CA”) appears on the left, and on the right the current
Call Alert setting is shown.
Press the S\T button to hear and select from the 1~3 available CALL
Alert tones. Select CALL Alert tone 4 to choose the VIBRATE Alert
function.
Press the MODE button again to continue programming.
!
Note : To transmit a Call Alert tone or Vibrate Alert, press the
SCAN button twice rapidly.
Page 15
www.bluestarcomm.net
Model BR777
PROGRAMMING THE VOX (HANDS-FREE TRANSMISSION)
Your BR777 radio has 3 VOX level settings (oF/1/2/3).
In the PROGRAM mode, press the MODE button until the “VOX”
icon appears while the current VOX setting appears on the right.
Press the S\T button to select between “0”, “1”,”2”, or “3” VOX
setting.
Press the MODE button again to continue programming.
!
Note : VOX will be more sensitive on the “1” setting than on the “3”
setting. Selecting “0” will disable the VOX function, and the VOX
icon will not appear on the display during operating.
CLONING THE RADIO SETTINGS
You can copy the BR777 radio settings from one radio (SOURCE) to
another BR777 radio (TARGET) by using a Cloning Cable.
Note to start the Cloning Process without the Cloning Cable
attached to the radios.
To clone the radios:
- Set both the SOURCE and TARGET radio into PROGRAM mode.
- Press the MODE button of both radios until the CLONE icon (shown
as “CLON”) appears on the right, and below a “CL” is shown.
- Press the Tbutton of the TARGET radio and the RX icon will appear.
- Press the Sbutton of the SOURCE radio and the TX icon will appear.
- Attach the Cloning Cable on both radios.
- Press again the Tbutton of the TARGET radio and you will see 4
segments blinking in sequence in the LCD display.
- Press again the Sbutton of the SOURCE radio and you will see 4
segments blinking in sequence in the LCD display.
- Once the cloning process is done, a “P” will appear on the display.
- Remove the cloning cable from the radios.
- Exit the cloning process by pressing the MODE button for more than
3 seconds until the unit is powered off.
Page 16
www.bluestarcomm.net
Model BR777
KEYPAD LOCK
To avoid accidentally changing the radio setting, press the LOCK
button for more than 3 seconds. The KEY LOCK icon will appear on
the display. PTT and CALL will still be active. Repeat the same
procedure to unlock the keypad.
EXTERNAL SPEAKER/MICROPHONE JACK
Your BR777 Series can be used with an optional external
speaker/microphone or headset, freeing your hands for other tasks. To
use an optional speaker / microphone or headset:
l Insert the plug(s) into the SPK/MIC jack.
l Place the earbud into your ear, and adjust the
mic into your desired position.
Page 17
www.bluestarcomm.net
Model BR777
TROUBLESHOOTING GUIDE
PROBLEM
SOLUTION
No Power
- Check battery installation and/or replace batteries
Cannot Receive
Messages
- Confirm the radios have the same channel
and Privacy Code settings.
- Make sure that you are within range of the other
transceivers.
- Buildings and other structures may interfere with
your communication.
Radio is not responding
to button presses
- Make sure key lock is not on. See "Keypad Lock"
(Page 17).
- Radio might need to be reset. Turn radio off then
on.
- Ensure accessory microphone is set properly
Display is dim
- Recharge or replace batteries.
Charger not functioning
- Contacts on the bottom of the radio may require
cleaning.
- Ensure the outlet where the charger is plugged
into is functioning properly.
- Check that the battery pack is installed in the
radio properly.
USE AND CARE
1. Use a soft damp cloth to clean the radio
2. Do not use alcohol or cleaning solutions to clean the radio.
3. Do not immerse the radio in water.
4. Dry the radio with dry lint-free cloth should it get wet.
5. Turn off the radio and remove the batteries during long-term
storage.
If you have a problem which you believe requires service, please
call Blue Star customer service at 1-800-630-4684 and speak with
a service technician first. Many problems can be remedied over
the phone without returning the unit for service.
Page 18
www.bluestarcomm.net
Model BR777
SPECIFICATIONS
Channels
4 Channels (56 Frequencies) + 121 Privacy Codes
Operating Frequency UHF 461.0375 ~ 469.5625 MHz
Power Source
3.7Vdc Li-ion Battery Pack
FREQUENCY CHART (MHz)
Display
FREQUENCY
(MHz)
Display
FREQUENCY
(MHz)
Display
FREQUENCY
(MHz)
1
464.5000
20
461.3125
39
466.1625
2
464.5500
21
461.3375
40
466.1875
3
467.7625
22
461.3625
41
466.2125
4
467.8125
23
462.7625
42
466.2375
5
467.8500
24
462.7875
43
466.2625
6
467.8750
25
462.8125
44
466.2875
7
467.9000
26
462.8375
45
466.3125
8
467.9250
27
462.8625
46
466.3375
9
461.0375
28
462.8875
47
466.3625
10
461.0625
29
462.9125
48
467.7875
11
461.0875
30
464.4875
49
467.8375
12
461.1125
31
464.5125
50
467.8625
13
461.1375
32
464.5375
51
467.8875
14
461.1625
33
464.5625
52
467.9125
15
461.1875
34
466.0375
53
469.4875
16
461.2125
35
466.0625
54
469.5125
17
461.2375
36
466.0875
55
469.5375
18
461.2625
37
466.1125
56
469.5625
19
461.2875
38
466.1375
Page 19
www.bluestarcomm.net
Model BR777
PRIVACY CODE CHART (ANALOG)
Display
Number
Frequency (Hz)
Display
Number
Frequency (Hz)
1
67.0
20
131.8
2
71.9
21
136.5
3
74.4
22
141.3
4
77.0
23
146.2
5
79.7
24
151.4
6
82.5
25
156.7
7
85.4
26
162.2
8
88.5
27
167.9
9
91.5
28
173.8
10
94.8
29
179.9
11
97.4
30
186.2
12
100.0
31
192.8
13
103.5
32
203.5
14
107.2
33
210.7
15
110.9
34
218.1
16
114.8
35
225.7
17
118.8
36
233.6
18
123.0
37
241.8
19
127.3
38
250.3
Note: Privacy codes can be programmed for use on any channel
Page 20
www.bluestarcomm.net
Model BR777
PRIVACY CODE CHART (DIGITAL)
Display
Number
Digital
Code
Display
Number
Digital
Code
Display
Number
Digital
Code
39
023
67
174
95
445
40
025
68
205
96
464
41
026
69
223
97
465
42
031
70
226
98
466
43
032
71
243
99
503
44
043
72
244
100
506
45
047
73
245
101
516
46
051
74
251
102
532
47
054
75
261
103
546
48
065
76
263
104
565
49
071
77
265
105
606
50
072
78
271
106
612
51
073
79
306
107
624
52
074
80
311
108
627
53
114
81
315
109
631
54
115
82
331
110
632
55
116
83
343
111
654
56
125
84
346
112
662
57
131
85
351
113
664
58
132
86
364
114
703
59
134
87
365
115
712
60
143
88
371
116
723
61
152
89
411
117
731
62
155
90
412
118
732
63
156
91
413
119
734
64
162
92
423
120
743
65
165
93
431
121
754
66
172
94
432
Note: Privacy codes can be programmed for use on any channel
Page 21
www.bluestarcomm.net
Model BR777
LIMITED WARRANTY
Blue Star will repair or replace, at its option without charge, any Blue
Star by MIdland BR777 transceiver which fails due to a defect in
material or workmanship within Two Years following the initial
consumer purchase. This warranty does not apply to water damage,
battery leak or abuse.
Accessories have a 90 day warranty from date of purchase, including
any antennas, chargers, or earphones. This warranty does not include
the cost of labor for removal or re-installation of the product in a
vehicle or other mounting. Performance of any obligation under this
warranty may be obtained by returning the warranted product, prepaid
freight, along with proof of purchase to:
Blue Star
Customer Service
12410 W 62nd Terrace
Shawnee, KS 66216
This warranty gives you specific legal rights, and you may also have
other rights, which vary from state to state.
Note : The above warranty applies only to merchandise purchased in
the United States of America or any of the territories or possessions
thereof, or from a U.S. Military exchange.
Blue Star
Customer Service
12410 W 62nd Terrace
Shawnee, KS 66216
URL: www.bluestarcomm.net
Page 22
www.bluestarcomm.net
Model BR777
ACCESSORIES
Accessories can be purchased at www.bluestarcomm.net or call
1-800-630-4684.
BRC501
- 1 Dual Desk Charger
- 1 AC Adapter
BATT7L
- 1 Li-ion Battery Pack
Page 23
www.bluestarcomm.net
Model BR777
BA100
- 1 Replacement Belt Clip w/ screw
BA300
- 1 Swivel Holster
BA700
- 1 Cloning Cable
Page 24
www.bluestarcomm.net
Customer Service: 12410 W 62nd Terrace Shawnee, KS 66216
Note: Features & Specifications are subject to change without notice.
MIDLAND and BLUE STAR are not responsible for unintentional errors or
omissions on its packaging.
Rev A
BLUE STAR by MIDLAND
BR777 PROGRAMMING QUICK REFERENCE GUIDE
To enter the PROGRAM mode, start with the radio powered off and press and
hold the SCAN button and PTT button simultaneously while you power the
radio on; done by pressing the MODE button for 3 seconds. The radio will
beep and display all the LCD segments for a few seconds. The Program icon
(shown by PROG) icon will appear, the channel number flashes, and the
Frequency icon (shown by FREQ) and Privacy Code icon (shown by CODE)
will be displayed alternately.
To exit PROGRAM mode, press the MODE button for 3 seconds then the unit
will power off.
Setting the
Channel
- Press the S or T button.
Setting the
Frequency
- Press the
button until FREQ
appears.
- Press the S or T button to change
the frequency.
Setting the
Privacy Code
- Press the
button until CODE
appears.
- Press the S or T button to change
the Privacy Code.
Setting the
SCAN List
- Press the
button until “y”
appears.
- Press the S or T button to select
between “y” or “n”.
- Selecting “y” will include the channel
during scanning.
- Selecting “n” will exclude the channel
during scanning.
MODE
MODE
MODE
BLUE STAR by MIDLAND
BR777 PROGRAMMING QUICK REFERENCE GUIDE
Setting the
Call Alert/
Vibrate Alert
- Press the
button until “CA”
appears.
- Press the S or T button to select
the Call Alert tone between 0~4.
- Selecting “0” will disable the Call
Alert function.
- Selecting “1~3” will set the Call Alert
tones.
- Selecting “4” will disable the Call
Alert and enable the Vibrate Alert.
The Vibrate Alert icon
will appear
on the display.
Setting the
VOX
- Press the
button until “VOX”
appears.
- Press the S or T button to set the
VOX level.
Cloning the
Radio setting
Start this process without the
Cloning Cable attached to the radios.
- Set both radios to Program mode.
- Press the
button until “CL”
appears on both radios.
- Press the T button on Target radio.
RX will appear.
- Press the S button on Source radio.
TX will appear.
- Connect the Cloning Cable.
- Press again the T button on Target
radio.
- Press again the S button on Source
radio.
- “P” will appear on the display when
Cloning is finished.
- Remove the Cloning Cable and turn
off the radios.
MODE
MODE
MODE
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement