A-Neu Video HD-88LA Instruction manual
A-Neu Video HD-44 is a powerful 4x4 HDMI matrix switcher that allows you to connect up to four HDMI sources to four HDMI displays and switch between them effortlessly. With support for resolutions up to 4K@60Hz, HDR, and HDCP 2.2, you can enjoy stunning visuals and immersive audio. The front panel buttons, IR remote control, RS-232, and Ethernet connectivity provide flexible control options. Whether you're setting up a home theater, gaming room, or conference room, the A-Neu Video HD-44 has you covered.
Advertisement
Advertisement
HD-88LA
8x8 HDMI Matrix Switcher
INSTRUCTION MANUAL
A-NeuVideo.com | Frisco, Texas 75034 | (317) 456-2461 V.1.2
SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to qualified service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing.
19. Service Information Equipment should be serviced by qualifier service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL
TABLE OF CONTENTS
CONTENTS
PACKAGE CONTENTS ...............................................................1
INTRODUCTION & FEATURES ................................................. 2
SPECIFICATIONS ....................................................................... 3
FRONT PANEL ............................................................................4
REAR PANEL ..............................................................................7
TYPICAL APPLICATION .............................................................8
REMOTE CONTROL .................................................................10
IR ExTENDER .........................................................................12
EDID FUNCTION .................................................................... 13
ETHERNET SERIAL INTERFACE ............................................17
RS-232 SERIAL INTERFACE ...................................................18
GUI INTERFACE .......................................................................19
PACKAGE CONTENTS
1. Main console Matrix Switcher unit.
2. Operating Instructions
3. IR remote controller (HD-88IR)
4. 19-inch ear mount bracket (Part # 1U-440 L)
5. IR extender SB-100 receiver (300M length)
6. IR extender SB-100C receiver (2M length)
7. 16x HDMI connector use ISO screw (L5mm/OD3mm)
8. CD contents: This manual, Windows GUI
9. RS-232 Cable
10. Power Supply 12VDC, 5A Universal Type 50/60Hz, 100~240 VAC
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for any infringements of patents or other rights of third parties which may result from its use.
We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update or to keep current the information contained in this document.
We reserve the right to make improvements to this document and/ or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or otherwise — without express written permission and consent
© Copyright 2015. All Rights Reserved.
Version 1.2 JAN 2015
1
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the companies with which they are associated.
FEATURES
INTRODUCTION
The HD-88LA is high-performance 8x8 matrix routing switcher for HDMI signals. This switcher supports data rates up to 6.75 Gbps, enabling 1080p HDMI formats and UXGA/WUXGA/DVI resolution to any HD display. High Definition Digital signals can be selected and distributed to any (8) outputs simultaneously. The Switcher is certified as being fully HDMI and HDCP compliant, with RoHS, CE, FCC certification. Support high resolution HDMI sources routed to HDMI displays, monitors, and projector or audio receivers. The EDID can be selected between (8) different modes. Control is provided via front panel push buttons, IR remote, RS-232 or TCP/IP (not a web-browser).
An RS-232/Ethernet Windows GUI software program is provided for matrix routing control (Windows only).
(2) unique features of the HD-88LA is separate audio Inputs and Outputs.
On any Input, you can use a DVI to HDMI adaptor (not included) and a separate audio signal. The video will be embedded on the
Output signal. On any Output, you can take advantage of the SPDIF (coaxial digital) audio output. This is an excellent feature that allows audio to connect directly to an audio receiver. The S/PDIF can carry (2) channels of uncompressed lossless PCM audio or compressed
5.1/7.1 surround sound such as Dolby Digital Plus or DTS-HD High Resolution Audio. But, it does not have the capacity to carry the uncompressed data in the lossless formats of Dolby TrueHD and DTS-HD Master Audio – as HDMI does.
FEATURES
• 8x HDMI digital source devices matrix switched to 8x HDMI devices
• HDMI digital video w/embedded audio, DVI format and CEC/HDCP 2.0 compliant
• (7) function key control and worldwide (8) EDID modes for HDTV resolutions
• Link speeds of up to 6.75 Gbps (link clock rate of 340Mb Hz), Support HDMI 1.4a 3D formats
• Support (DVI) Audio input and SPDIF output.
• Wide range of HD resolutions from PC xGA to WUxGA 1920x1200 and HDTV/DTV resolutions 480i/480p, 576i/576p, 720p, 1080i & 1080p
• Compatible with all HDMI source devices, PC monitors, Plasma HD display, HDTV and audio receivers/amplifiers.
• Digital Video TMDS formats Resolutoin up to 1080p-60 with Deep color 36-bit
• Digital Audio Support :
• Dolby TrueHD, Dolby Digital, Dolby Digital Plug/ex,
• DTS, DTS-HD, DTS-HD Master, DTS-Ex
• PCM, PCM2, LPCM2
• Various User Interface control:
• Windows based GUI control via RS-232 port or Ethernet
• Front Panel push button
• IR wireless remote control
• Third party RS-232 control
• Third party Ethernet control
• Support world wide control functions: ALL/OFF/RECALL/ENTER/MEMORY/EDID/LOCK
• Support EDID modes :
• Embedded EDID modes : FSS/H24-3D/H24-3D-M/H36-3D/H36-3D-M/DVI-D 1280x1024-60Hz/DVI-D 1920x1200-60Hz/AUTO
• External modes : Learning mode
• Automatic scanning input & output status via LED show on front panel
• Support preview output port simultaneously output #1
• Support IR Remote and IR Extender with distance up to ~ 1000ft (300M) Maximum
• EDID configuration via Internal modes.
• Consumer Electronic Control (CEC) switch all open or OFF
The Switcher will remember that last state during a power cycle.
When power is removed and resorted, the last configuration will be invoked
2
SPECIFICATIONS
SPECIFICATIONS
• Type of HDMI Switcher: 8x HDMI Inputs to 8x HDMI Outputs Matrix Switcher
• HDMI Support: HD 1080p@60Hz, H36-bit Deep color, 3D (1.4a) formats
• HDCP/CEC Support: HDCP 2.0 Compliant, CEC Compliant
• Video Bandwidth: Double Data Rates: 340Mhz, Total 6.75Gbps bandwidth
• Digital Video Support: Full HD resolution : 480i / 480p / 720p / 1080i / 1080p
• Digital Audio Support: Multi Audio Formats 5.1 / 7.1, MAT(MLP), Dolby Digital, Dolby TrueHD, Dolby Digital Plus, DTS, DTS-ES
6.1, DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH)
• Controls:
• IR Remote Controller or External port (3.5mm Ear phone Jack)
• Select & Function buttons on front panel
• RS-232 series interface
• Use Ethernet Control switcher
• Audio Support: Support Audio Input and SPDIF output
• Source Status: Automatically Scan Sources Inputs via LED
• Function Control Key: ALL / OFF / RECALL / ENTER / MEMORY / LOCK / EDID
• Infrared Frequency: 38 Khz
• IR External Distance: ~1000 ft / 300M maximum
• HDMI I/O Connector: HDMI Type A - SMD 19pin Female Type
• Temperature: 32°F - 100°F Operation (0°C - 38°C)
• Dimensions (LxWxH): 19 x 9.85 x 1.75 in (482x250x44 mm)
• Rack Mount: Rack Mount 1RU High 19 ”Rack Mount (with rack mount)
• Power Supply: DC12V / 5A, Universal world wide Type 50/60Hz, 100~230 VAC
• Power Consumption: 3880 mA Maximum
• Safety Approvals: CE, FCC, RoHS (2002/95/EC)
• Product Weight: 4.2 lb/2.50 Kg
Note: Specifications are subject to change without notice.
Because of limitations on source and display devices, not all EDID data is compatible and subsequently not all equipment will function correctly with this switcher.
3
FRONT PANEL
FRONT PANEL
q
POWER SWITCH
The power switch turns the unit on and off. The LCM will illuminate red to indicate that the switcher is ON and is receiving power.
The Switcher will remember that last state during a power cycle.
When power is removed and resorted, the last configuration will be evoked.
w
INPUT STATUS DISPLAY
Input sources 1 to 8 LCM illuminates blue to indicate that a video source is present on that input.
e
OUTPUT STATUS DISPLAY
Each Output (destination) Channel shows which input (source) is assigned.
r
DESTINATION SELECT BUTTONS
Separate outputs 1 thru 8 select buttons are provided for each destination assignment.
Routing can be Source to Destination or one source to multiple destinations.
Example : Press Destination 1, 3, 5 then press Source 2 will route Input 2 to Output 1, 3, 5 respectfully.
t
EDID MODE SELECT BUTTONS
Used to select EDID mode using buttons #1 thru #2 y
IR SENSOR
The IR sensor receives IR commands from the supplied remote controller or third party IR emitter.
u
SOURCE SELECT BUTTONS
Separate inputs 1 thru 8 select buttons are provided each source selection.
4
FRONT PANEL
FRONT PANEL
i
FUNCTION KEY - ALL
Disables (mute) video on all destinations OR Selects the same source to all destinations.
Option 1
- Press ALL followed by OFF button. The display will show “ 0 “ indicating all destinations have no video selected.
Option 2
- Press ALL followed by Source 1 thru 8. The display will show the Source selected.
- Press ENTER The pre-set source selection will be assigned all destinations.
o
FUNCTION KEY - OFF
Disables (mute) video to selected channels. Either destinations.
- Press OFF button followed by any Destination channel.
- Press 1 thru 8 output destination. The display will show “ 0 “ for the selected channel indicating no video selected .
a
FUNCTION KEY - RECALL
The system will show previously stored presets, up to a total of 16.
Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location.
- Press RECALL button.
- Press 1 thru 8 on either Source or Destination row.
- Press ENTER The pre-set configuration will execute.
Operation completes.
Operation will abort if no keys are pressed with 5 seconds.
s
FUNCTION KEY - ENTER
- Press ENTER to confirm entries.
5
FRONT PANEL
FRONT PANEL
d
FUNCTION KEY - MEMORY
The system will show store presets, up to a total of 16.
Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location.
- Configure desired matrices.
- Press MEMORY button.
- Press 1 thru 8 on either Source or Destination row.
- Press ENTER to ready memory location.
- or press MEMORY again to cancel operation.
Operation completes.
Note : Operation will abort if no keys are pressed within 5 seconds.
f
FUNCTION KEY - LOCK
- Press and hold LOCK button for two seconds lockout the front panel.
- Press and hold LOCK button for two seconds to enable the front panel.
g
FUNCTION KEY - EDID
- Press EDID to select new EDID mode or select source row #1 or #2 for LINK source EDID again.
- Press the DESTINATION # to learn EDID. The Destination EDID has been learned.
h
19 INCH EAR MOUNT PAIR
Converts desktop to 19 inch rack mount. Bracket (part # 1U-440L) INCLUDED.
Image shows rack mount bracket attached.
6
REAR PANEL
REAR PANEL
q DC POWER INLET
The Switcher is fitted with a DC power plug input connector. Ensure that the used is of an approved type and is of sufficient current carrying connector capacity with the correct voltage and connector polarity. 12Volt DC power supply 5A Max (Center pin positive).
w IR EXTENDER CONTROL
Support one of IR Extender (IR input). Extend distance maximum
984 ft (300 m) Note: DO NOT install or remote this connection with the power ON.
e RS-232 CONNECTION
RS-232 control port to allow for interfacing to a PC, Such as a computer or touch panel control, to the switcher via this DB-9pin
Female connector for serial RS-232 control. r ETHERNET CONNECTION
Connect a signal link of Ethernet direct to this Female RJ-45 connector. This connector supports Ethernet control via a PC by support AP and protocol commands.
ty OUTPUTS- 1,2,3,4,5,6,7 & 8 HDMI
Connect a signal link of HDMI direct digital video/audio to this Female
HDMI connector. This connector supports HDMI digital video/audio and DVI digital video sources. HDMI Digital
Video/Audio, Connector with fix screw Output 1 ~ Output 8 ui INPUTS- 1,2,3,4,5,6,7, & 8 HDMI
Connect a signal link of HDMI direct digital video/audio to this Female
HDMI connector. This connector supports HDMI digital video/audio and DVI digital video sources.
HDMI Digital Video/Audio, Connector with fix screw Input 1 ~ Input 8
7
Power Jack:
DC Jack - Inner OD ᴓ 2.1mm (+ )
Outside OD ᴓ 5.5mm (GND)
Power input - 12VDC, 5A
IR Extender Jack:
Female Jack - inner OD ᴓ 3.5 mm
Remote port :
DB-9pin Female connector
Remote port : Control the switcher RJ-45
Female connector
Ethernet Port: Note: the Ethernet port and
RS-232 port cannot be used simultaneously. Any connection to the Ethernet port will disable serial commands send to the RS-232 port.
HDMI digital video/audio connector:
HDMI Female connector.
Note: With the proper adapters, the switcher can be used with DVI digital video signals HDCP compliant.
DVI audio support 2CH..
SPDIF: Use RCA connector with digital audio signals output.
HDMI digital video/audio connector:
HDMI Female connector.
Note: With the proper adapters, the switcher can be used with DVI digital video signals HDCP compliant.
The DVI support Audio input.
Audio: Support the audio input when you use DVI signals.
TYPICAL APPLICATION
INSTALLING DIAGRAM
Sample connection using IR Transmitters and IR Receiver to control a projector via HDBaseT™ Transmitter and HDBaseT™ Receiver.
NOTE:
1. IR Control Projector Over HDBaseT™ Extender: Use HDBaseT™
Transmitter & HDBaseT™ Receiver
2. Audio Input : Uspport DVI Audio input.
3. RS-232 Control
4. External IR Remote.
5. IR Extension port : Control Switcher.
6. Ethernet port : Control Switcher via Ethernet.
Support HDBaseT™ Extender by Transmitter and Receiver via CAT6/6a/7 cable
8
TYPICAL APPLICATION
INSTALLING DIAGRAM
Sample connection using DVI & Audio input and link to the AUDIO Amplifier via SPDIF digital signal output.
NOTE :
1. Use DVI and Audio Input via DVI Player Device.
2. HDMI display support DVI input via HDMI HDTV Support DVI input
3. SPDIF output Via COAX cable To Audio Amplifier.
Support DVI and Audio input by SPDIF output to Audio Amplifier
9
REMOTE CONTROL
Before making any connections to the switcher. Observe the following:
> Ensure the mains voltage supply matches the label on the
supplied plug-pack (+/- 10%)
> Ensure that the power switch is OFF
> Ensure that all system grounds (earth) are connected to a
common point.
> Avoid powering equipment within a system from multiple power
sources that may be separated by large distances
> Connect all audio video sources and destination equipment
> Power up all source and destination audio-visual sources
> For each destination output select the appropriate input source
by using the front panel input 1~8 select buttons. The supplied
IR remote control. Or through the RS-232 serial communications
port.
> Upon power up the switcher will return to its last used setting
before powered down.
REMOTE CONTROL
qw
IR REMOTE CONTROL KEY :
w
SWITCH 1 POWER ON or OFF
Controller with a separate power ON and OFF e
DESTINATION : 1 thru 8 OUTPUT SELECTION
Press the destination button to select the output display channel.
r
SOURCE : 1 thru 8 INPUT SOURCE SELECTION
Press input 1~8 sources with selection button t
FUNCTION KEY
ALL - function selection button
OFF - function selection button
EDID - function selection button
RECALL - function selection button
MEMORY - function selection button
ENTER - function selection button
LOCK - function selection button
10
REMOTE CONTROL
IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD)
HOW TO SETUP IR CODES :
Model number : HD-88LA
CUSTOM CODE : 38C7
POWER ON : 38C7 A15E
POWER OFF : 38C7 A25D
ALL : 38C7 B04F
OFF : 38C7 B14E
EDID : 38C7 B748
LOCK : 38C7 B54A
RECALL : 38C7 B24D
MEMORY : 38C7 B44B
ENTER : 38C7 B34C
PRESS DESTINATION then - # PRESS SOURCE - #
DESTINATION #1 : 38C7 10EF
DESTINATION #2 : 38C7 20DF
DESTINATION #3 : 38C7 30CF
DESTINATION #4 : 38C7 40BF
DESTINATION #5 : 38C7 50AF
DESTINATION #6 : 38C7 609F
DESTINATION #7 : 38C7 708F
DESTINATION #8 : 38C7 807F
SOURCE #1 : 38C7 01FE
SOURCE #2 : 38C7 02FD
SOURCE #3 : 38C7 03FC
SOURCE #4 : 38C7 04FB
SOURCE #5 : 38C7 05FA
SOURCE #6 : 38C7 06F9
SOURCE #7 : 38C7 07F8
SOURCE #8 : 38C7 08F7
For example;
Select Destination # 1 to show Source #1~8,
The IR Data Code list :
Destination # 1 , Source #1 38C7 10EF 38C7 01FE
Destination # 1 , Source #2 38C7 10EF 38C7 02FD
Destination # 1 , Source #3 38C7 10EF 38C7 03FC
Destination # 1 , Source #4 38C7 10EF 38C7 04FB
Destination # 1 , Source #5 38C7 10EF 38C7 05FA
Destination # 1 , Source #6 38C7 10EF 38C7 06F9
Destination # 1 , Source #7 38C7 10EF 38C7 07F8
Destination # 1 , Source #8 38C7 10EF 38C7 08F7
11
IR ExTENDER
1. ANI-100 IR 300M Receiver Switcher IR EXT. In Cable (3C) IR Receiver (ANI-100)
Distance: Max.300M
IR PN#: ANI-XXXX
R oHS /95/E C
R S -232 IR E XT. in
INP UT
DC 12V
IR Rx
RS - 232 IR EXT .
ANI-100
I M
AT
ANI-100 IR Receiver Set
ANI-100 Maximum Distance ~ 984 feet (300M)
Control Switch ANI-XXXX
The ANI-100 IR Receiver is required when using the port “ALL in” Jack.
SW
IR
2. ANI-100C IR 2M Receiver Switcher IR EXT. In Cable (2C) IR Receiver (ANI-100C)
IR Receiver cable 6ft (2M)
Distance: Max.(2M)
R oHS /95/E C
IR PN#: ANI-XXXX
R S -232 IR E XT. in
INP UT
DC 12V
IR Rx
I M
AT
RS - 232 IR EXT .
ANI-100
SW
IR
ANI-100C IR Receiver Cable
ANI-100C Maximum Distance ~ 6 feet (2M)
Control Switch ANI-XXXX
The ANI-100C IR Receiver will not function on the port “ALL in” Jack.
*** When you plug the External IR extender into the switcher, the front panel IR receiver remains active. ***
Pin configuration for IR 984 feet (300M) Extender Receiver such as ANI-100 compatible
VCC (Ring)
Tip: Signal
Ring :VCC
Sleeve: GND
Tip Ring
Ring
Sleeve
GND (Sleeve)
Sleeve Tip (center)
Signal (center)
ANI-100 IR Receiver Set
ANI-100 Receiver and ANI-101 Transmitter The DISTANCE maximum ~ 984 feet (300M)
Pin configuration for IR Receiver 6 feet (2M) cable such as ANI-100C compatible
IR Receiver cable 6ft (2M)
Sleeve
Tip: Signal
Ring: NC
Sleeve: GND
Tip Ring
Ring
ANI-100C IR Receiver Cable
Sleeve Tip (center)
Signal (center)
ANI-100 Receiver and ANI-101C Transmitter The DISTANCE maximum ~ 984 feet (300M)
GND (Sleeve)
Note: The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug (aka: stereo plug).
Using a 2-conductor plug will short out the power supply. Always make connections with the switcher power off.
12
EDID FUNCTION
EDID FUNCTION SETUP
EDID setup To change the EDID setup
Step 1. Press the EDID button
Step 2. Press SOURCE #1 or #2 button row
Step 3. Press the ENTER button
The display will show the currently selected EDID mode
The button will flash blue and the display will show the current Embedded EDID
Status.
To set EDID mode.
The switcher will return to operation mode.
Operation will abort if no keys are pressed within 5 seconds.
Embedded EDID modes
Embedded EDID setup
Total 8 EDID Modes
To select Embedded EDID mode or LEARNING mode
Press EDID button : The LCM will show the current EDID status.
Press EDID > SOURCE > ENTER
SOURCE #1 or
SOURCE #2
RESET
How to RESET EDID mode
Press EDID > RECALL > ENTER
Repeatedly depressing the source 1 button will cycle up thru the options.
Repeatedly depressing the source 2 button will cycle down thru the options.
Select Embedded EDID :
Mode 1 : FSS
Mode 2 : H24-3D
Mode 3 : H24-3D-M
Mode 4 : H36-3D
Mode 5 : H36-3D-M
Mode 6 : DVI-D 1280x1024-60Hz
Mode 7 : DVI-D 1920x1200-60Hz
Mode 8 : AUTO
EDID Return To Factory default
RESET To the FACTORY DEFAULT (1080p-2CH).
Press EDID button : The LCM will show the current EDID status.
Press RECALL button : The LCM will show the RESET EDID.
Press ENTER to confirm entries.
The EDID will return to FSS mode and resolution 1080p-2CH.
LEARNING EDID
Learning EDID setup
Press
EDID > DESTINATION > SOURCE > ENTER
Learning EDID from Destination to Source
Press EDID > DESTINATION Button. The LCM will be show LEARNING.
Switcher will LEARN destination EDID and pass the selected source.
13
EDID FUNCTION
NOTE : The already learned EDID cannot be modified. You can only rebuild a new Learning EDID.
For example: When the Source has “Learned” the EDID data from a destination, It will save that EDID information into EPROM and the EDID data cannot change.
Please select new learning destination to sources or change to one of the embedded EDID modes when you want to remove the learning EDID memory from EPRPM.
EDID function : 8x Embedded EDID Modes
Mode 1. FSS ® (Fast Speed Start) Fast Speed Start mode shortens the startup time of the switcher. Selecting this mode does not force the EDID setup to be cancelled. Users may first select one EDID mode from mode 2 to 3, and then select mode 1 for fast speed start.
Mode 2. H24-3D (1080p-24 bits) Video Support : All resolutions up to and including 1080p.
Audio Support : PCM 2CH
Mode 3. H24-3D-M (1080p-24bits)
Mode 4. H36-3D (1080p-36 bits)
Video Support : All resolutions up to and including 1080p.
Audio Support : MAT(MLP) 7.1CH, PCM 2CH, One Bit Audio 2CH, AC-3
5.1CH, DTS 5.1CH, PCM 7.1CH, Dolby Digital + 7.1CH, DTS-HD 7.1CH
Video Support : All resolutions up to and including 1080p.
Audio Support : PCM 2CH
Mode 5. H36-3D-M (1080p-36 bits)
Mode 6. 1280x1024-60Hz (DVI-D)
Video Support : All resolutions up to and including 1080p.
Audio Support : MAT(MLP) 7.1CH, PCM 2CH, One Bit Audio 2CH, AC-3
5.1CH, DTS 5.1CH, PCM 7.1CH, Dolby Digital + 7.1CH, DTS-HD 7.1CH
DVI Support : DVI-D 1280x1024 60Hz
DVI Support : DVI-D 1920 x 1200 60Hz Mode 7. 1920x1200-60Hz (DVI-D)
Mode 8 . AUTO <Default> Video Support : All resolutions up to and including 1080p.
All Outputs will be set to the highest common resolution of all connected display devices.
14
EDID FUNCTION
EDID FUNCTION : LEARNING
Learning EDID Single to Single
Step 1.
Press the EDID button
Example : Learn Destination #8 EDID To Source #5.
The button will flash blue and the display will show the current Embedded EDID
Status.
Copy the Destination #8 Display EDID.
Step 2.
Press the Destination #8 button row
Step 3 . Press the Source #5 button row Learning the Destination #8 EDID To Source # 5.
Step 4.
Press ENTER button To confirm entries.
Learning EDID Single to multiple
Step 1.
Press the EDID button
Learning destination EDID link to the majority Sources
The button will flash blue and the display will show the current Embedded EDID
Status.
Step 2.
Press the Destinations #1~8 button row Copy any 1~8 Destinations EDID.
Step 3.
Press the Source #1, #6,~#8 button row Learning the Destination EDID link to source #1,#6,~#8.
Step 4.
Press ENTER button To confirm entries.
Learning EDID Single to ALL
Step 1.
Step 2.
Press the EDID button
Press destination button 1 thru 8
Step 3.
Press ALL button
Learning destination EDID link to All Sources
The button will flash blue and the display will show the current Embedded EDID
Status.
Learning anyone 1~8 Destination EDID to all sources.
Learning selected destination EDID to all sources.
Step 4.
Press ENTER button To confirm entries.
EDID FUNCTION FOR HDMI MATRIX SWITCHER
EDID status To view the current EDID status.
Step 1.
Press the EDID button
The button will flash blue and the display will show the current Embedded EDID
Status.
Step 2.
Press the EDID button To exit.
How to setup FSS ® Function
Step 1.
Press the Destination #1~8 button row
Then Press the Source #1~8 button row
Step 2.
Press the EDID button
Fast speed start ®
To setup and Install all devices.
Step 3.
Press ENTER button
Step 4.
Press the EDID button
Step 5.
Press ENTER button
Select a optimum status of Embedded EDID mode.
To conform entries.
To select the EDID FSS ® mode.
To conform entries.
LEARNING EDID definition Learning EDID from Destination to Source
1. Switcher will LEARN destination EDID and pass the selected source.
2. To set up learning between a single destination and single source:
Press EDID button > Press Destination 1 thru 8 > Press Source 1 thru 8 > Press ENTER to confirm.
Switcher will learn destination EDID to source device.
3. To set up learning between a single destination and Multiple sources:
Press EDID button > Press Destination 1 thru 8 > Press the majority Sources 1 thru 8 > Press ENTER.
Switcher will learn single destination EDID to many source devices.
4. How to Learning single destinations with all sources. Press EDID button > Press ALL button > Press ENTER to confirm.
15
EDID FUNCTION
AUTO MODE definition Common Resolution and Audio
Switcher will find highest common Resolution and Audio from all destination EDID to link Source.
Example for single source
Destination > press #1 and then Source > press #1
Destination device #1 will set to the highest common resolution and Audio of source #1
Example for multiple sources
Destination device #1, #2, #3 will be set to the highest common resolution and Audio available and source device #1 will output this same resolution.
16
ETHERNET SERIAL INTERFACE
ETHERNET SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM. VERSION COMPATIBLE V2.0
For a complete list of commands, please reference external document extended Ethernet Protocol Instruction Manual.
Example of the commanded string to route Input 3 to Output 4
OUTPUT04 03;
ETHERNET SERIAL INTERFACE
Pin Ethernet Reference
1 TxOP TX +
2
3
TxON
RxIP
Tx -
RX +
Note :
Control the switcher
SPD : Speed
LINK : Ethernet link
RJ-45 Female 8P-8Cconnector
4
5
6
7
8
NC
NC
RxIN
NC
GND
Rx -
ETHERNET TCP/IP PROTOCOL COMMANDS ( Ethernet / RS-232 Control driver V2.0 )
*** When Ethernet is used, the switcher will not accept commands from the RS-232 port. ***
17
RS-232 SERIAL INTERFACE
RS-232 SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM. VERSION COMPATIBLE V2.0
For a complete list of commands, please reference external document extended RS-232 Protocol Instruction Manual.
Example of the commanded string to route Input 3 to Output 4
OUTPUT04 03;
RS-232 SERIAL INTERFACE
Pin RS-232 Definition
1 -------Not used
4
5
6
7
2
3
8
9
Tx
Rx
--------
GND
--------
--------
--------
--------
Transmitter
Receiver
Not used
Ground
Not used
Not used
Not used
Not used
RS-232 PROTOCOL COMMANDS ( RS-232 Control driver V2.0.1 )
The switcher can be controlled via the RS-232 serial control port to allow for interfacing to a PC, or similar third party control system.
The serial communication parameters are 9600 baud, 8 bit, No Parity and 1 stop bit - this is often referred to as 9600 8N1.
When the unit recognizes a complete command it will perform the requested action - there is no delimiter character required.
QUICK START:
Data String Format:
The Data String contains four elements.
[Command][ ][Data][;]
The format is:
1. Command
2. Space
3. Data
4. ;
There is a single space after the Command and before the Data string.
The data string must conclude with an “;” (without the quotes).
All text is full ASCII Code and is NOT case sensitive.
LINK is the same as Link. You can use either capital letters or small letters and get the same result.
Function
Power Off
Command
Power 00:
Power On
Input 3 to Output 4
All Input 5
Power 01;
OUTPUT04 03;
OUTPUTALL 05;
18
GUI INTERFACE
1A: Supports routing using Lines
19
GUI INTERFACE
1B: Supports routing using Cross points
20
GUI INTERFACE
2: Select different matrix sizes
21
GUI INTERFACE
3: Support COM ports 1 thru 4
22
TERMS AND CONDITIONS OF USE
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED
BY, THROUGH OR UNDER A-NEUVIDEO, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-NeuVideo, Inc. at the return address set forth on the Product’s packing label at your expense. A-NeuVideo, Inc. may modify these Terms and Conditions at anytime, without notice to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product.
You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be borne by you and you agree to indemnify and hold harmless A-NeuVideo, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to A-NeuVideo. Any intellectual property rights pertaining to the Product are licensed to you by A-NeuVideo, Inc. and/or its affiliates, including any manufacturers or distributors of the Product (collectively, “A-NeuVideo”) for your personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by A-NeuVideo for your personal use only.
A-NeuVideo does not transfer either the title or the intellectual property rights to the Product and A-NeuVideo retains full and complete title to the intellectual property rights therein. All trademarks and logos are owned by A-NeuVideo or its licensors and providers of the Product, and you may not copy or use them in any manner without the prior written consent of A-NeuVideo, which consent may be withheld at the sole discretion of A-NeuVideo.
The functionality and usability of the Product is controlled by A-NeuVideo, Inc. from its offices within the State of Texas, United States of America. A-NeuVideo makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided with respect thereto. You are advised that the Product may be subject to U.S. export controls.
Disclaimers and Limitation of Liability
A-NeuVideo may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. A-NEUVIDEO DOES NOT WARRANT OR
MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY,
OR OTHERWISE.
A-NeuVideo has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, A-NEUVIDEO DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
A-NEUVIDEO DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT.
A-NEUVIDEO DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO
THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS.
A-NEUVIDEO WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT
TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT A-NEUVIDEO) ASSUME THE ENTIRE COST OF ALL
NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY
A-NEUVIDEO.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL A-NEUVIDEO BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL
DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF
A-NEUVIDEO OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL A-NEUVIDEO’S TOTAL
LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU
PAID TO A-NEUVIDEO, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT
23
Advertisement
