EPV-Image VSC User Manual

EPV-Image VSC User Manual
EPV IMAGE VSC
VIDEO PROCESSOR USER MANUAL
Elation Support
Thank You for Purchasing the EPV IMAGE VSC
Thank you for your purchasing the Elation Professional EPV IMAGE VSC Scaler and
LED wall control system. Please read the instructions in this manual carefully and
thoroughly before attempting to operate this unit. These instructions contain
important information regarding safety during use and maintenance. Please fill
out and return the enclosed warranty card to validate your purchase.
Customer Service
Elation provides a toll free customer support line, to provide set up help and to
answer any question should you encounter problems during you set up or initial
operation. You may also visit us on the web at www.elationlighting.com for any
comments or suggestions.
All returned service items whether under warranty or not, must be freight pre-paid
and accompany a Return Authorization (RA) number. The RA number must be
clearly written on the outside of the return package. Items returned without a RA
number clearly marked on the outside of the package will be refused and returned
at customer’s expense. You may obtain a RA number by contacting customer
service.
A brief description of the problem as well as the RA number must be written down
on a piece of paper and included in the shipping container. If the unit is under
warranty, you must also provide a copy of your proof of purchase invoice.
Customer Service hours are Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific
Standard Time.
Toll Free: (866) 245-6726
Phone: (323) 582-3322
Fax: (323) 832-9142
Information: [email protected]
Sales: [email protected]
Support: [email protected]
Forum: forums.elationlighting.com/eve
2-Year Limited Warranty
Elation® hereby warrants, to the original purchaser, Elation Professional®
products to be free of manufacturing defects in material and workmanship for a
period of 2 Years (730 days) on all internal parts, components, and labor.
This
warranty shall be valid only if the product is purchased within the United States
of America, including possessions and territories.
It is the owner’s
responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
For warranty service, send the product only to the Elation factory. All shipping
charges must be pre-paid.
If the requested repairs or service (including parts
replacement) are within the terms of this warranty, Elation will pay return
shipping charges only to a designated point within the United States except
Hawaii or Alaska.
If the entire instrument is sent, it must be shipped in its
original package. No accessories should be shipped with the product.
If any
accessories are shipped with the product, Elation shall have no liability
whatsoever for loss of or damage to any such accessories, nor for the safe
return thereof.
This warranty is void if:
•
The serial number has been altered or removed
•
The product is modified in any manner which Elation concludes, after
inspection, affects the reliability of the product
•
The product has been repaired or serviced by anyone other than the
Elation factory unless prior written authorization was issued to purchaser
by Elation
•
The product is damaged because not properly maintained as set forth in
the instruction manual
This is not a service contract, and this warranty does not include maintenance,
cleaning or periodic check-up.
During the period specified above, Elation will
replace defective parts at its expense, and will absorb all expenses for warranty
service and repair labor by reason of defects in material or workmanship.
The
sole responsibility of Elation under this warranty shall be limited to the repair of
the product, or replacement thereof, including parts, at the sole discretion of
Elation.
All products covered by this warranty were manufactured after
January 1, 1990, and bear identifying marks to that effect.
Elation reserves the right to make changes in design and/or improvements upon
its products without any obligation to include these changes in any products
theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to
any accessory supplied with products described above.
Except to the extent
prohibited by applicable law, all implied warranties made by Elation in
connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above.
warranties,
whether
expressed
or
implied,
including
And no
warranties
of
merchantability or fitness, shall apply to this product after said period has
expired.
The consumer’s and or Dealer’s sole remedy shall be such repair or
replacement as is expressly provided above; and under no circumstances shall
Elation be liable for any loss or damage, direct or consequential, arising out of
the use of, or inability to use, this product.
This warranty is the only written warranty applicable to Elation Products and
supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
Revision
Format
1.0
Time
2010-12-23
ECO#
Description
Principal
0000
Release
Lisa
CONTENT
1.0 Safety ........................................................................................... 1
2.0 Specification ................................................................................... 1
2.1 Specification/Parameters ............................................................ 2
3.0 Connection ..................................................................................... 4
3.1 EPV IMAGE VSC Back Panel......................................................... 5
3.2 How to install ............................................................................ 7
4.0 Front Panel Keyboard Operation ........................................................ 7
4.1 EPV IMAGE VSC Operator Guideline.............................................. 8
4.2 Video Processor Menu ................................................................ 9
5.0 Communication Software Guideline.................................................. 14
5.1 Install Software ....................................................................... 14
5.2 Run EPV IMAGE VSC Console..................................................... 18
6.0 FAQ............................................................................................. 27
6.1 No output in target display........................................................ 27
6.2 VGA input could not work with EPV IMAGE VSC Console ................ 27
6.3 DVI input could not work with EPV IMAGE VSC ............................ 27
6.4 Component input could not work with EPV IMAGE VSC.................. 28
6.5 User settings can not save ........................................................ 28
6.6 Can’t update main board software.............................................. 28
6.7 Display SDI1 or SDI2 in dual display mode.................................. 29
6.8 HDMI display shows blue screen ................................................ 29
6.9 Can’t be saved ALPHA value ...................................................... 29
7.0 Quick Start................................................................................... 30
7.1 Single-screen control ............................................................... 30
7.2 Set dual screen fade ................................................................ 32
7.3 Displaying subtitles and LOGO ................................................... 33
7.4 How to control processor with console software by USB? ............... 38
7.5 How to Use LINSN Ledset software? ........................................... 42
8.0 Appendix ..................................................................................... 44
8.1 AppendixⅠDownload the main board software............................. 44
8.2 Appendix II Download the IP software ........................................ 53
8.3 Appendix Ⅲ How to add tasks................................................... 55
1.0 Safety
The general safety information in this summary is for operating person. Any
requirement, please feel freely to contact our service engineer.
Power Source
This product is intended to operate from a power source
between 85~265 volts rms . This product is only workable under
correct power condition, which is already mark on the back panel
of the power.
High Voltage
There are many high voltage components inside.
Do not Remove Covers and Panels
Do not remove Covers in any conditions. There are not any
spare components inside for maintenance, so do not maintain
this product by userrselves, any requirement, please feel free to
contact our service engineer. Keep heavy device from power
cord.
Grounding the Product and Use the Proper Fuse
This product is grounded through the grounding conductor of
the power cord. To Avoid electrical shock, plug the power cord
into a properly wired receptacle before connecting to the product
input or output terminals.
Keep away from Magnet, Motor, TV and Transformer.
Guard Against Damp
Keep using inside clean and dryness environment, once the
device get wet, must remove power cord right now.
Keep away Exploder
Do not operate the device inside dangerous and easy
explosive gas, which it may make fire, blast or something without
expectation.
Keep away Pour Liquid and Fragment
It is forbid to pour liquid, metal fragment or anything else
inside this device to avoid fire and other accident. Once that
happens, must remove power cord and try to make it clean
before power on again.
2.0 Specification
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
1
EPV IMAGE VSC series video processors are designed by the latest high
performance image processing technology. EPV IMAGE VSC can handle
following video without limit, include CVBS(Composite)、S-Video (YC)、YCbCr
、YPbPr、RGBHV(VGA)、DVI-D、HDMI、SDI(SD-SDI、HD-SDI) and VOIP
(Copper RJ45).
2.1 Specification/Parameters
Composite BNC Input
Number of Inputs
3
Supported Standards
PAL/NTSC
Signal Level
1Vpp±3db
Multiplex
YCbCr
(0.7V Video+0.3v Sync ) 75ohm
S-video DIN4 Input
Number of Inputs
1
Supported Standards
PAL/NTSC
Signal Level
Y:1Vpp±3dB
(0.7V Video+0.3v Sync ) 75ohm
U/V:0.7Vpp±3dB 75ohm
YPbPr BNC Input
Number of Inpus
BNC*3
Supported Standards
analog HD input
Signal Level
Y:1Vpp±3dB
(0.7V Video+0.3v Sync ) 75ohm
Pb/Pr:0.7Vpp±3dB 75ohm
VGA DB15 Input
Number of Inputs
1
connetor
Standard DB15 socket
Supported Standards
VGA-UXGA
Signal Level
R、G、B、Hsync、Vsync:0 to1Vpp±3dB
(0.7V
Video+0.3v Sync ) 75 ohm
black level:300mV Sync-tip:0V
DVI Input
Number of Inputs
1
Connector
Standard DVI-I socket
Supported Standards
SMPTE:625/25 PAL, 525/29.97 NTSC, 625/50p
PAL,
525/59.94p
NTSC,
1080i50,
1080i59.94/60, 720p50 720p59.94/60
VESA : 800×600×60Hz , 1024×768×60Hz ,
1280×768×60Hz
1600×1200×60Hz
,
,
1280×1024×60Hz
,
1920×1080×60Hz
,
1920×1080×50Hz
Signal Level
TMDS pwl,single pixel input,165MHz bandwidth
Standard
DVI 1.1
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
2
SDI Input
Number of Inputs
2
Connetor
BNC
Data Rate Range
19.4Mbps~1.5Gbps
Supported Standards
ITU-R
BT.656,ITU-R
BT.601,SMPTE
259M,
SMPTE 292, SMPTE 297
Equalization)
Belden 1694A 100M HD1.485G , 350m SD
270Mbps
SDI Loop-out
Number of Loop-Throughs
1
Signal Level
800mV±10%
DC Offset
0V±0.5V
Rise/Fall Time
HD1.485Gbps<270 ps ; SD 270 Mbps 0.4
ns~1.5ns
Overshoot
<10%
Timing Jitter
SD<0.2UI;HD<1.0UI
Alignment Jitter
<0.2UI
HDMI Input
Number of Inputs
2
Connector
HDMI (standard type A interface)
Supported Standards
SMPTE:625/25 PAL, 525/29.97 NTSC, 625/50p
PAL,
525/59.94p
NTSC,
1080i50,
1080i59.94/60, 720p50 ,720p59.94/60
VESA : 800×600×60Hz , 1024×768×60Hz ,
1280×768×60Hz
1600×1200×60Hz
,
1280×1024×60Hz
,
1920×1080×60Hz
,
,
1920×1080×50Hz
Signal Level
TMDS pwl,single pixel input,165MHz bandwidth
Standard
HDMI 1.3
SDI Loop-out
Number of Loop-Throughs
1
Signal Level
800mV±10%
DC Offset
0V±0.5V
Rise/Fall Time
HD1.485Gbps<270
ps ; SD270
Mbps
0.4
1024×768×60Hz
,
ns~1.5ns
Overshoot
<10%
Timing Jitter
SD<0.2UI;HD<1.0UI
Alignment Jitter
<0.2UI
DVI Output
Number of Inputs
1
connetor
Standard DVI-I interface
Supported Resolution
800×600×60Hz
1024×768×75Hz
EPV 701 User Manual
,
,
1280×768×60Hz
Doc. No:RGB-RD-UM-V618E012
3
,
1280×1024×60Hz
,
1440×900×60Hz
,
1400×1200×60Hz
,
1600×1200×60Hz
,
1920×1080×60Hz
,
1920×1200×60Hz
,
2048×1152×60Hz
TMDS pwl,165MHz bandwidth
Signal Level
VGA Output
Number of Inputs
1
connetor
Standard DB15 socket
Supported Resolution
800×600×60Hz
,
1024×768×60Hz
,
1024×768×75Hz
,
1280×768×60Hz
,
1280×1024×60Hz
,
1440×900×60Hz
,
1400×1200×60Hz
,
1600×1200×60Hz
,
1920×1080×60Hz
,
1920×1200×60Hz
,
2048×1152×60Hz,2048×1536×60Hz
R、G、B、Hsync、Vsync:0 to1Vpp±3dB
Signal Level
(0.7V
Video+0.3v Sync ) 75ohm
black level:300mV Sync-tip:0V
HDMI Output
Number of Outputs
1
Connetor
HDMI (standard type A
interface)
Supported Standards
800×600×60Hz
1024×768×60Hz
1024×768×75Hz
,
,
,
1280×768×60Hz
,
1280×1024×60Hz
,
1440×900×60Hz
,
1400×1200×60Hz
,
1600×1200×60Hz
,
1920×1080×60Hz
,
1920×1200×60Hz
,
2048×1152×60Hz
TMDS pwl,165MHz bandwidth
Signal Level
Function
Source Switch
Support every signal with alpha key operation
PIP
PIP for SD with HD and HD with HD
Alpha Key
support
Extras
Communication
RS232
Power Supply
85-264V 2A IEC-3
Working Environment
0°C~45°C
Stored Environment
10% to 90%
Product Warranty
1year
Note:
TCP/IP
Specifications are subject to change without notice.
3.0 Connection
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
4
3.1 EPV IMAGE VSC Back Panel
1、Dial the code switch;
2 、 10/100M interface (copper RJ45). Used to connect the computer by
568B-568A twist-pair
3、USB interface,Used to connect the computer
4、RS232 interface (RJ11) for EPV IMAGE VSC processor. Used to connect the
computer;
5-6、HDMI input interface。Input the signal from HD player, DVD, computer, and
so on.
7-8、SDI Input BNC, used to support SD/HD SDI input。Input the video signal
from the HD player, HD projector. It can connect to the 7 or 8 interface on the
next EPV IMAGE VSC,using the 75ohm BNC.
9、SDI loop out BNC, used to loop input SDI signal to next SDI player.
10-11、Gigabit copper port, connect to LED screen.
12、Gigabit Transmitter card USB control interface;
13、Gigabit Transmitter card DVI input,connect to DVI output of EPV IMAGE
VSC;
(This Connection does not support hot-plugging)
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
5
14-16、Composite input interface,Composite BNC. Used to input composite
signal (PAL, NTSC, SECAM compatible);
17 、 S-Video DIN 4, used to input S-Video signal ( PAL, NTSC, SECAM
compatible);
18、DVI input interface。Input the video signal from computer, DVI signal
generator. Connect to the same DVI interface on VSP;
(This Connection does not support hot-plugging)
19-21、R/Pr G/Y B/Pb BNC, used to support SD/HD progressive input, up to
1080p60;
22、VGA input interface, DB-15, used to support Analog RGB input; connect to
the VGA interface on VSP;
23、HDMI output, use to connect with HDMI monitor or HDMI player;
24、DVI output,connect to the monitor or LED display with DVI interface.
(This Connection does not support hot-plugging)
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
6
25、VGA output interface, connect to the monitor, projector and so on;
26~27、Switch and power. It must use IEC-3 power line. Always ground to avoid
electric shock.
3.2 How to install
EPV IMAGE VSC frame size
4.0 Front Panel Keyboard Operation
Insert power cord and push power to ON position. LCD module on the front
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
7
panel will show ELATION LIGHTING and go into self verification before it load
last setting config and send processed image to the target monitor. For the first
setup, CV1 input is default source. With front panel keyboard, user can operate
VSP with menu display on LCD module.
4.1 EPV IMAGE VSC Operator Guideline
EPV IMAGE VSC front panel as following:
1、 LCD Module;
2、 Keyboard:
ESC: push to exit from current choice item;
SEL: push to confirm the current choice item;
UP: push to select up items;
DOWN: push to select down items;
LEFT: push to select left items;
RIGHT: push to select right items;
CV1:switch to composite 1 input;
CV2:switch to composite 2 input;
CV3:switch to composite 3 input;
SVID: switch to
s-video input;
YCbCr:switch to standard definition input;
VGA: switch to analog RGB input;
YPbPr: switch to high definition component;
DVI: Switch to DVI input;
SDI1:switch to SDI1 input;
SDI2:switch to SDI 2 input;
HDMI1:switch to HDMI 1 input;
HDMI2:switch to HDMI 2 input;
SAVE1:switch to use the user-defined mode 1;
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
8
SAVE2:switch to use the user-defined mode 2;
PBP:switch to show two pictures beside on beside;
PIP:switch to show picture in picture on the screen. CV1 is the default
small picture on the top left corner,
DVI is the default picture full
screen;
POP:switch to show picture out picture on the screen;
FS:switch to selet full screen or zoom view, just for single picture
mode;
MENU: push to go to main menu;
FRE:push to freeze the video image or live again
(FreezeLiveFreeze)
AB: push to switch between front picture and back picture if works in
dual channel mode with alpha key, front picture will alpha key in step by
step and back picture key out step by step;
SCALE: push to go to between scalezoomcropscale mode;
BRT:push to adjust the brightness and the contrast ratio, push to enter
to the relevant Menu, and then push the UP and DOWN to adjust the
brightness and the contrast ratio;
OUT: push to select the output format by using the UP and DOWN;
I/II: push to set single or dual channe;
SAVE: push to save current config;
4.2 Video Processor Menu
System menu as follows;
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
9
> EPV701
*Dev Info
Recall
↓
Fig. 1
The first line shows EPV IMAGE VSC.
Push the right and left direction key to select the left or right menu. Before
the menu item, if there is a * sign, means the menu item has been selected;
you can push the Select key to enter it.
The
on the right means you can select the menu items by pushing the up
and down direction key.
User can check the information of the equipment in “Dev Info” menu
(including the manufacturer、serial-number );
User can get more service and support according to the serial-number.
ELATION LIGHTING
>SN:3204
User can check current input and output sources in Dev Info menu also.
Input: CV1 1024x768x60
Output: CV2 1024x768x60
Touch UP/DOWN to check System time
System time:
2009-08-17
15:12:35
User can do a Factory Settings in Recall menu, after successful reset you will
see the menu as follows:
Factory reset was completed !
Push the MENU to enter the main menu, and then push up and down
direction key, the menu as follows:
> EPV701
*Language
Alpha
↑
Push the LEFT/RIGHT to select the relevant submenu.
LANGUAGE submenu as follows:
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
10
*LANGUAGE
>Chinese
English
Push UP/DWON to enter Alpha setup, user can set value from 0 to 100,
0 means video or graphic would be disappear and 100 means normal;
Port A and Port B stand for two channel picture;
*Alpha
Port A Value:
100
Push OUT to enter the Output menu, push the UP or DOWN to select
different output resolution, push OK to confirm the output resolution.
Advance submenu as follows:
Added adjustable feature of DE;
Press UP/DOWN and select the menu as shown in Figure 1:
> EPV701
*Advance
XY_Pos ↑
Figure 1
Press LEFT/RIGHTand select XY_Pos to enter the submenu of adjusting
effective area;
H_BLANK
*HS:
46
V_BLANK
*VS:
38
XY_Pos:The sub-menu of which is used to adjust the position of overall effective
area shown on the screen or monitor.
H_BLANK: The overall effective area can be moved around by adjusting the
value of H_BLANK.
V_BLANK:The overall effective area can be moved up and down by adjusting the
value of V_BLANK.
Added adjustable feature of DE,support the following resolution:
Note:
"800x600x60 Hz "、"1024x768x60 Hz "、"1024x768x75 Hz "
"1280x1024x60 Hz "、"1400x1050x60 Hz "、"1600x1200x60 Hz "
Screen parameter:
Hsize:
EPV 701 User Manual
1024
Doc. No:RGB-RD-UM-V618E012
11
Screen parameter:
Hsize:
1024
Step:user can set the step of scale;
HSize:set the horizontal size of the image;
VSize:set the vertical size of the image;
HPos:set the horizontal position of the image;
VPos:set the vertical position of the image;
User can set size and position of the screen simply, Mainly applies to LED
screens users. After setting screen parameter, the user choice PIP or PBP
operation, display picture can directly shows on corresponding screen。
Output
>1024x768x60
Push the
/
to enter Single or Dual channel menu , push the UP / DOWN to
select the single or dual channel, push SEL to confirm the single channel or
dual channel work state;
Setup
Dual
Setup
Single
Select the input channel, push the UP/DOWN, and SEL to confirm the
different input channel. User can also push the channel name on the
keyboard to go into the input channel.
Source Select
>CV1
AB in EPV IMAGE VSC is for two image Alpha in and out.
Setup
A on B
OR:
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
12
Setup
A on B
Push SCALE to set the size and position of the image, push UP/DOWN and
SEL to confirm the relevant items;
Step:user can set the step of scale;
HSize:set the horizontal size of the image;
VSize:set the vertical size of the image;
HPos:set the horizontal position of the image;
VPos:set the vertical position of the image;
Scale
> Step
10
Push the FRE to freeze the live image or live the freeze image.
Freeze Frame
Once gain for live
OR:
Live Frame
Once gain for live
Push BRT to set the brightness and the contrast ratio:
> EPV701
Brightness
50 ↓
> EPV701
Contrast
50 ↑
OR:
Push SAVE and then push SAVE1 or SAVE2 to save the operation to SAVE1 or
SAVE2;Push SAVE1 or SAVE2 to execute relative operation after user save
the operation sucessfully.
Select Save Mode !
Push Esc To Exit
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
13
5.0 Communication Software Guideline
EPV IMAGE VSC video processor is very easy to be configured with user
friendly communication software, support drag and drop operation for edit and
display. Also can customized with schedule function.
5.1 Install Software
Dual click EPV IMAGE VSC.exe to install, select Chinese or English version
for use,after click “select ”to next dialog.
If user agree to install this software, please click next to go on, else click esc to
exit this install.
And in next dialog is the user agreement of the software, click agree to go on
and refuse to exit.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
14
If users agree to the agreement, user can select install directory in next
dialog, else, click next to install software to default directory “C:\Program Files”.
Click “next”to go on.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
15
Click “next” to go on.
Click “finish” and ready to run EPV IMAGE VSC console.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
16
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
17
5.2 Run EPV IMAGE VSC Console
Run EPV IMAGE VSC.exe and the console will auto detect device in serial or
networks by detected Comm port and pro-define IP address.
After detect, open the device console, for example, if the device is EPV IMAGE
VSC, then EPV IMAGE VSC console will be load, as following.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
18
Setup Communication
EPV IMAGE VSC Console support COM port or Ethernet (UDP) to access EPV
IMAGE VSC.For the first running ,user must click the
Click
to close COM Port.
to change the COM Port and the Baudrate.
Serial: user can make choice between existent com ports and baud rates;
default Baudrate is 115200.
Ethernet: user can fill any number less than 1023 in Local Port. The Remote Port
must be 192.168.0.100 and the Remote Port must be 1000.
The COM Port is decided by user’s COM. Right click my computer icon on
desktop, select HardwareDevice Manager in the system attributes dialog. The
COM in red in the picture is the COM user can make choice.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
19
Then click
to open COM.
will display after success to
connect the COM.
If EPV IMAGE VSC console success to detect device in chain, the software
version, device core version, firmware version and serial number will display on
the bottom right corner of the screen.
5
How to use
Operator can check parameters by software.
: Save script. Save current user config parameters as script.
: Open script. User can open saved script.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
20
: Import template. There are six templates for user.
: Export template. Export current config as template.
: Option. User can choose open device when start and using script saved
before or execute schedule edited before when start.
If user choose open device when start, user can use last run, use script file or
none when user start. User can click
to choose which script user want to
open.
If user choose execute schedule when start, the next dialogue will display when
software run.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
21
: Language. The software supports Chinese and English version. The
picture following is the Chinese dialogue.
: Exit.
Communication
: Open COM.
: Close COM.
: Set COM.
Device
: Synchronization.
: Save to flash.
:Load form Flash.
: Factory setup
: Advance, for adm. inistrator control.
: Execute schedule or stop schedule.
Help
: Help. Display helps dialogue.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
22
: About.
Output resolution: user can choose different output resolution by selecting
from pull down list.
Operating mode: choose to work in single channel or dual channel.
Layout: if in dual channel mode, user can set the device to work in PIP or PBP
mode directly with quick preset layout button as following.
Input: the white area display the name of input interface when the mouse is
over the interface picture on the left. The orange pane means current selected
interface.
If work in dual channel, channel 1 includes VOIP, CV1, CV2, CV3, SVideo, YCbCr,
SDI 1 and SDI 2, and channel 2 includes DVI, YPbPr, VGA, HDMI1 and HDMI 2.
The cross over interface picture means they can not access. The orange pane
means selected interface for channel 1. The blue pane means selected interface
for channel 2.
Screen parameter:
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
23
User can set size and position of the screen simply, Mainly applies to LED
screens users. After setting screen parameter, the user choice PIP or PBP
operation, display picture can directly shows on corresponding screen。
Images: User can scale the images;Image 2 can’t choose in single channel
mode.
Display Toolbar:
Display toolbar Users can set Alpha value of “dynamic Video” and “static current
frame” through display toolbar.
Setting Gamma is generally not recommended, since LED large screen itself has
Gamma function.
For further information, users can contact with our customer service team.
Output: user can customize the brightness and the contrast.
Display: user can customize image or images position and size just by drag and
drop image (images) in this area. This process is sync to the parameters in
images toolbars.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
24
Log: user can save or delete the operate log file.
Added functions

Alpha delay time
Alpha can set AB button Fade effect.

IP set
Users can set equipment IP, Usually used under the condition of one
computer control or remote control several computers.

Clock
Users can set or adjust lower computer time through” clock”
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
25

Equipment Schedule function
Users can set device to work with schedule, and then device can automatically
switch between single or dual channel, resize image, switch video and with fade
effect in need.
Equipment currently supports max 10 regular content; users can set in the
“timing” option.
Specifically how to implement devising schedule function, please refer to
Appendix
.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
26
6.0 FAQ
6.1 No output in target display
1) Check the output config of the input video.
2) Check the input channel config is ok. Ex.The composite 1 interface is
connected to the composite interface of video source.
3) Check the connection of output is ok.
4) Check the target monitor or display is not destroied or power down.
5)Check the output resolution of EPV IMAGE VSC is not out of the maximal
resolution
of target display.
6) Check ALPHA value is not 0.
7)Any requirement, please feel free to contact our customer service engineer.
6.2 VGA input could not work with EPV IMAGE VSC Console
1)Check VGA source output is ok.
2)Check VGA input resolution is not out of EPV IMAGE VSC Console support list,
as following. The biggest input resolution is 1024*768*60Hz
3) Check EPV IMAGE VSC Console works in VGA input mode.
4) Any requirement, please feel free to contact our customer service engineer.
6.3 DVI input could not work with EPV IMAGE VSC
1) Check DVI source is ok.
2) Check DVI source output is not out of EPV IMAGE VSC support list.
3) Check EPV IMAGE VSC works in DVI input mode.
4) Check the connection between EPV IMAGE VSC and DVI source is correct.
Restart DVI source and check output.
5) Any requirement, please feel free to contact our customer service engineer.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
27
6.4 Component input could not work with EPV IMAGE VSC
1) Check the connection between EPV IMAGE VSC and Component source is
correct. Especially Y signal. Refer to cabling example in page 5. High Definition
component YPbPr is only support in YPbPr input。Standard definition YCbCr
support 480i and 576i only; High Definition YPbPr support 480i、576i、480P、
576P、720P50、720P60、1080i50 and 1080i60;
2) Check component source works, normally DVD component output should be
open from its menu.
3) No recommend to output component and SVideo input from the same source.
4) Any requirement, please feel free to contact our customer service engineer.
6.5 User settings can not save
EPV IMAGE VSC supports multi config mode. For multi config mode, the
equipment starts to work automatically with the SAVE1 mode. According to
different equipments, you can solve the problems that modes can’t be saved by
the following steps.
EPV IMAGE VSC
Confirm to press the “SAVE” button, then press “SAVE1”,or “SAVE2”, that will
save the current operation mode to the “user mode 1”,or ”user mode 2”, after
that, gently push button “SAVE1”,””SAVE2, it will call out the corresponding
setting of user-mode. If that, the saving is successful.
After saving process, user should not do factory reset or any saving operation to
user mode 1, otherwise, “SAVE1” will be over write.
6.6 Can’t update main board software
Connect the computer and EPV IMAGE VSC Series, select *.mot. Download file
to device.
After the equipment power up, right-click the “.mot” file at the left side of menu,
when the screen shows “waiting for update”, you can update the main board
program. Next, choose the “download file to device”, start to loading.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
28
6.7 Display SDI1 or SDI2 in dual display mode
The way to display SDI1 or SDI2 in dual display mode: select SDI1 or SDI2
when in single display mode, press
/
to enter into dual display mode then
select SDI1 or SDI2 as source signal
6.8 HDMI display shows blue screen
In dual channel and the picture composition is: SDI+HDMI(including SDI1,
SDI2 and HDMI1, HDMI2 combine together),
switching between SDI1 and
SDI2, or other signals switching to SDI1 or SDI2, when HDMI display shows blue
screen, then user needs to reselect the HDMI working signal.
6.9 Can’t be saved ALPHA value
ALPHA value can’t be saved when operating the AB key on the front panel to do
FADE IN FADE OUT, so user has to revise the corresponding value in the
Advanced Menu to save it.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
29
7.0 Quick Start
7.1 Single-screen control
Set screen parameters
Users can easily change the screen size and location by setting the parameters
with keyboard and LCD menu.
Press MENU to access main menu, Menu shows as below picture:
>EPV IMAGE VSC
*Dev Info
Recall
↓
Press UP / DOWN button to turn the menu shown as below pictures:
>EPV IMAGE VSC
*Advance
Screen parameter:
Hsize:
↑
1024
Step: Set the unit of zoom and move every time;
HSize:Set Horizontal size;VSize:Set vertical size;
Hpos:Set horizontal coordinates(horizontal phase);
VPos:Set vertical size(vertical phase);
Scale pictures
Step:Set the unit of scale and move every time; (Three steps available:1,
10,100)
HSize:Set horizontal size; VSize:Set vertical size;
HPos:Set horizontal coordinates(horizontal phase);
VPos:Set vertical size(vertical phase);
Scale
> Step
10
Set alpha
Enter Alpha sub-menu can set the alpha of video, Press UP /DOWN to set the
value of alpha; Port A and Port B represent two video channels;
*Alpha
Port A Value:
EPV 701 User Manual
100
Doc. No:RGB-RD-UM-V618E012
30
Set brightness contrast
BRT brightness and contrast button can set brightness and contrast of active
window video shown as below pictures:
EPV IMAGE VSC
Brightness
50 ↓
EPV IMAGE VSC
Contrast
50 ↑
BRT brightness and contrast button can set brightness and contrast of active
window video shown as below pictures:
EPV IMAGE VSC
Brightness
50 ↓
EPV IMAGE VSC
Contrast
50 ↑
Freeze Frame
Press FRE static frame button can freeze, press the button can freeze current
active window image; You can make the screen switch between static and
active with this button; Pictures show as below:
Freeze Frame
Once gain for live
or
Live Frame
Once gain for live
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
31
7.2 Set dual screen fade
1. Press
/
button to switch between single channel or dual channel. Menu is
as follows:
Setup
Dual
Setup
Single
2.Choose two input source from CV1、CV2、 CV3 、SVID、 DVI、YPbPr、VGA、
SDI1、SDI2、HDMI and HDMI2.
3. Press AB button to realize dual screen fade.
CV1、CV2、 CV3 、SVID、SDI1 and SDI2 is small screen defaully, DVI、YpbPr、
VGA、HDMI1 and HDMI2 is big screen defaully while realizing dual screen, If you
want the two faded screens the same size, you can set the screen size by SCALE
button. For LED users, who are familiar with studio operation can also set the
display window on PC with studio software by the third party. And PC output by
VGA or DVI, Use SCALE to make the CV1、CV2、 CV3 、SVID、SDI1 and SDI2
the same size as studio display window. AB button can quickly realize dual
screen fade;
Step:Set the unit of zoom and move every time;
(Device default three step:1, 10,100)
HSize:set horizontal size;
VSize:set vertical size;
HPos:Set horizontal coordinates(horizontal phase);
VPos:Set vertical size(vertical phase);
Scale
> Step
10
Press LEFT/RIGHT keys or touch UP/DOWN,select menu; * in front of the menu
means this menu is selected. Press SEL key, you can enter corresponding menu
to set and view.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
32
7.3 Displaying subtitles and LOGO
Users could add subtitles and Logo on the video by "set subtitle" option in "Video
Processor" menu
 Subtitles switch
By "subtitles switch" function, users can choose whether to display subtitles and
subtitles background on the video.
Subtitles show on top of the image without subtitle
Note:
background.
Foreground transparency refers to subtitles’s transparency and background
transparency refers to subtitles background, which defaults to be 50%
transparent, user can not adjust the value of this transparency.
 Displaying Subtitles
Fill in the subtitles blank with words that you need to show on display(eg.
Advertising Slogans), maximum 80 characters allowed. Then click the “submit”
button, subtitles will appear on the screen soon.
Size of subtitles is limited, Chinese fonts defaults to be Times
Note: New Roman and size is 24X24 (pixels); English font defaults
to be Arial, size of 16X24 (pixels). The subitle font could not
be modified at present.
 Subtitles color or subtitles background color
Users can change the subtitles color or subtitles background color through
dragging the scroll bar by mouse or make choice in the color palette to select the
right color
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
33
 Subtitles movement
Figuration of parameters in the "subtitles rolling" menu, subtitles could be
rolling or static, at present, the device supports horizontal rolling( left or right)
only, vertical rolling is not available at present.
 Subtitle rolling Speed
Through dragging the scroll bar by mouse to set the speed of rolling subtitles.

Subtitles position
By setting the value of horizontal or vertical coordinates, subtitles position on
the screen can be adjusted.
Subtitles Width refers to the width of the subtitles display area. As long as the
parameters have been set, subtitles will be displayed in the figurated area.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
34

LOGO display
Users could made any LOGO displayed by the LOGO display function.
Users can choose whether to enable the LOGO display function according to
circumstance.
When users select the "background color mark", the screen background color
would be black and LOGO shows on it.
When users select "trademark transparent", LOGO would be translucent.
When users select "trademark transparent", LOGO would be
Note: translucent.
The value of this transparency could not be modified.
Users could change the image format and pixels with
software in window
OS. The picture would be cut on the right side and bottom if it is too big.
If the current picture is larger than the new size, the right side and the bottom
part of the picture will be cut off in order to adapt to smaller areas.
If the image is too big, users would have to cut the picture first. by the Toolbox.
Change image size, and then click "properties” on "image" menu, and select the
width and height of the measurement in pixels. Enter the width and height
values in the "width" and "height" box.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
35
the device support only 16 bit color bitmap in bmp format with
Note:
maximum pixels of 256X128
After LOGO picture was adjusted to specified size, save the image to 16 bit color
bitmap bmp format.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
36
 Download LOGO
After LOGO picture was adjusted to specified format and size, users could
download it to the device, and then enable the LOGO display function, the LOGO
would be displayed on the screen.
By setting the parameters of X or Y coordinates, LOGO position on screen can be
adjusted.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
37
7.4 How to control processor with console software by USB?
1. Install the driver;
Connect the USB cable to the PC and the video processor. Turn on the EPV
IMAGE VSC for the first time to use USB, the PC will remind finding the new
hardware and ask to install the driver for this new driver.
Install from the list or specified location, press “NEXT”:
Press “ browser” to find the driver, and press “NEXT”
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
38
When the installation finish, can go to check the installed COM port inside the
device management, as following picture show:
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
39
2. Install the console software, and run after install, shows the interface of the
console as following:
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
40
:Set the RS232 as installed just now, and set the EPV IMAGE VSC Boud
Rate to be: 115200.
Press
to start RS 232 communication, when there is green point in the
right down corner showing on the software, it means the communication is OK,
and you can use the software to control the device now; the software operation
is the same as EPV IMAGE VSC, just can see the difference of the SDI input;
If power off during communication, should close the port
Note:
by
first, and plug in out of the USB and do communication
again.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
41
7.5 How to Use LINSN Ledset software?
1. First, Install EPV IMAGE VSC software and LINSN software.
2. Run EPV IMAGE VSC software;
①Press
to set the RS232. first choose the current RS232 you are using,
then set the baud rate.
Press
to start the RJ232, when the green point showing on the right
down corner, it means the communication is successful.
Press
:option. Find the LINSN software installation file LEDSET.EXE
through “external progress route”as following picture:
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
42
As LINSN software will use RS232 for communication too, so user should first
close EPV IMAGE VSC console software RS232 communication after that press
;
If in used
, then to start the LINSN software. When you want to use EPV
IMAGE VSC software, you just need to close LINSN software, start the
RS232
again.
Before using EPV IMAGE VSC console software to execute the
Note::
LINSN software, you should first internally connect the device's
100M board with sending card.
Any question, please feel free to contact our customer service
engineer.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
43
8.0 Appendix
8.1 Appendix

Download the main board software
Installation
Double-click fdt2_2 setup.exe.
Click the next button.
Click the yes button.
Click the next button.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
44
Click the next button.
Unselected the H8S/2000, H8S/2000, H8. Click the next button.
Select 7144.45, Click the OK button.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
45
Select the location by browse. Click the next button.
Click the next button.
Click the next button.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
46
Click the finish button. It’s ok.

Download
Open the Flash Development Toolkit 2.2.
Click the OK button.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
47
Fill the name. Click the OK button.
Click the (Y)button.
Click the (Y)button.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
48
Fill the name. Click the OK button.
Select the sh/7145f. Click the next button.
Select the COM port. Click the next button.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
49
Click the next button.
Click the next button.
Click the finish button.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
50
Select project/properties/communications. select the COM port in user setting.
Do not check User default baud rate and select Target Baud as 9600.
Click the target files by the right mouse. Select add files to project , and select
user *.mot.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
51
Connect the computer and EPV IMAGE VSC Series, select *.mot. Download file
to device.
After the equipment power up, right-click the “.mot” file at the left side of menu,
when the screen shows “waiting for update”, you can update the main board
program. Next, choose the “download file to device”, start to loading.
After update, the device will auto run into operation mode without reset
process.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
52
8.2 Appendix II Download the IP software
Turn off the power, take the two coding switch to “ON” sate. As below:
Connect one side of the RJ11 download line to the RS232 on the video processor,
and the other side to be connected to the serial port on the PC.
Double click
to run Flash Magic ,setting as below:
First, users can choose the right serial port, set the baud rate to 115200, choose
LPC2368,and to load the aim document (hex.document) of IP board upgrading.
Secondly, confirm the two option box by tick.
Finally, click the “Start” button.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
53
After download, exit the program, turn off the power, tack the two coding switch
back, as below, restart the equipment power, check if the equipment work
normally.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
54
8.3 Appendix
How to add tasks.
Use “Device Schedule” can add tasks,make device automatically run to the
Schedule input source in specified time or schedule display modes such as fade
in and out.

First of all,set lower computer current time through host computer “clock”.
Reset to factory settings after setting the clock will affect the
Note:
time before.
After Clock setting, users can check whether successfully set through button.
Press MENU button to enter system main menu, then press Dev Info (device
information), then press SEL button can show device information. Touch
/DOWN,check in the System time. Shown as below picture:
System time:
2009-08-17

15:12:35
After device clock set, add task plan through” Timing Parameters”.
1. Users need to start “time-enabled” before using” timing device”. If you
forget to start, time set may fail.
Click “start” button
EPV 701 User Manual
, when the button changes to
Doc. No:RGB-RD-UM-V618E012
, it means
55
time can start.
Press MENU button can enter system main menu, touch UP/DOWN to enter
advanced menu, shown as the picture:
>EPV IMAGE VSC
*Advance
↑
Press SEL button to enter advanced menu
Time:
Time Able
2. When the timer count is set to 1, it indicates that the setting contents will be
stored in the “timing 1”. If you need to set more, you can set up one by one and
saved in different “Timer index”.
Note:
Equipment currently supports 10 task scheduler.
3. Set “task schedule” playing time,can up to second.
4. Select the signal source to play works in dual channel or single channel mode,
and check whether to use fade during dual channel mode.
5. Users can control the image position and size by change the data or click the
drop-down arrow.
6. When device works under the single channel mode, click the interface Icon.
Red box indicates current interface has been selected as the input interface;
When device works under the dual channel mode, need to switch image 1 and
image 2 set input signal one by one.
Users can see the image 1 and image 2 input source information in the input
source toolbar after setting. Shown as the picture:
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
56
7. When you finished above step, click button
to finish adding” tasks
plan”.
Click button
,you can see the input source, playing time, image size,
position etc. of the current “tasks plan”
Users can see all the “tasks plan” relevant content through “Timer index”
switching
.
EPV 701 User Manual
Doc. No:RGB-RD-UM-V618E012
57
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement