Sharp | MX-M363N | Setup guide | Sharp MX-M363N Setup guide

00-1(Cover12)_Setup.fm
1 ページ
2009年2月17日 火曜日 午前11時59分
MODEL: MX-M283N
MX-M363N
MX-M453N
MX-M503N
DIGITAL MULTIFUNCTIONAL SYSTEM
Software Setup Guide
BEFORE INSTALLING
THE SOFTWARE
SETUP IN A WINDOWS
ENVIRONMENT
SETUP IN A MACINTOSH
ENVIRONMENT
TROUBLESHOOTING
Keep this manual close at hand for reference
whenever needed.
!mxm503_us_ins.book
2 ページ
2009年1月22日 木曜日 午後2時21分
Thank you for purchasing this product. This manual explains how to install and configure the software that allows the
machine to be used as a printer or scanner for a computer.
This manual also explains how to install the printer drivers and software that are used when the expansion kits are
installed, and how to install the scanner driver.
If the software is not installed correctly or you need to remove the software, see "4. TROUBLESHOOTING" (page 40).
Please note
• The explanations in this manual assume that you have a working knowledge of your Windows or Macintosh computer.
• For information on your operating system, please refer to your operating system manual or the online Help function.
• The explanations of screens and procedures in this manual are primarily for Windows Vista® in Windows® environments, and
Mac OS X v10.4 in Macintosh environments. The screens may vary depending on the version of the operating system.
• Wherever "MX-xxxx" appears in this manual, please substitute your model name for "xxxx".
• This manual contains references to the fax function. However, please note that the fax function is not available in some
countries and regions.
• Considerable care has been taken in preparing this manual. If you have any comments or concerns about the manual, please
contact your dealer or nearest authorized service representative.
• This product has undergone strict quality control and inspection procedures. In the unlikely event that a defect or other problem
is discovered, please contact your dealer or nearest authorized service representative.
• Aside from instances provided for by law, SHARP is not responsible for failures occurring during the use of the product or its
options, or failures due to incorrect operation of the product and its options, or other failures, or for any damage that occurs due
to use of the product.
Warning
• Reproduction, adaptation or translation of the contents of the manual without prior written permission is prohibited, except as
allowed under copyright laws.
• All information in this manual is subject to change without notice.
Illustrations and the operation panel and touch panel shown in this manual
The peripheral devices are generally optional, however, some models include certain peripheral devices as standard equipment.
The explanations in this manual assume that a right tray and stand/2 x 500 sheet paper drawer are installed on the machine.
For some functions and procedures, the explanations assume that devices other than the above are installed.
The display screens, messages, and key names shown in the manual may differ from those on the actual machine
due to product improvements and modifications.
SOFTWARE LICENSE
The SOFTWARE LICENSE will appear when you install the software from the CD-ROM. By using all or any portion of the
software on the CD-ROM or in the machine, you are agreeing to be bound by the terms of the SOFTWARE LICENSE.
The explanations in this manual are based on American English and the North American version of the software.
Software for other countries and regions may vary slightly from the North American version.
For users of Windows 98/Me/NT 4.0
The CD-ROM does not include software for Windows 98/Me/NT 4.0.
Contact your dealer or nearest authorized service representative if you want software for Windows 98/Me/NT 4.0.
The scanner driver cannot be installed on Windows NT 4.0.
!mxm503_us_ins.book
1 ページ
2009年1月22日 木曜日 午後2時21分
TABLE OF CONTENTS
1
BEFORE INSTALLING THE
SOFTWARE
CD-ROMS AND SOFTWARE. . . . . . . . . . . . . . . . . . . . 2
• SOFTWARE CD-ROM . . . . . . . . . . . . . . . . . . . . . . 2
• OTHER CD-ROMS . . . . . . . . . . . . . . . . . . . . . . . . . 4
VERIFYING SYSTEM REQUIREMENTS . . . . . . . . . . . 5
• SYSTEM REQUIREMENTS . . . . . . . . . . . . . . . . . . 5
• SOFTWARE REQUIREMENTS . . . . . . . . . . . . . . . 6
CONNECTING THE MACHINE . . . . . . . . . . . . . . . . . . 7
• CONNECTING TO A NETWORK. . . . . . . . . . . . . . 7
• CONNECTING THE MACHINE WITH A USB
CABLE (Windows) . . . . . . . . . . . . . . . . . . . . . . . . . 7
2
3
SETUP IN A MACINTOSH
ENVIRONMENT
MAC OS X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
MAC OS 9.0 - 9.2.2. . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4
TROUBLESHOOTING
WHEN INSTALLATION WAS NOT SUCCESSFUL. . 40
REMOVING THE SOFTWARE . . . . . . . . . . . . . . . . . . 43
SETUP IN A WINDOWS
ENVIRONMENT
OPENING THE SOFTWARE SELECTION
SCREEN (FOR ALL SOFTWARE). . . . . . . . . . . . . . . . 8
INSTALLING THE PRINTER DRIVER / PC-FAX
DRIVER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
• WHEN THE MACHINE IS CONNECTED TO A
NETWORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
• WHEN THE MACHINE WILL BE
CONNECTED WITH A USB CABLE . . . . . . . . . . 16
• USING THE MACHINE AS A SHARED
PRINTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
• USING THE STANDARD WINDOWS PS
PRINTER DRIVER (Windows 98/Me/NT 4.0) . . . 21
• CONFIGURING THE PRINTER DRIVER FOR
THE OPTIONS INSTALLED ON THE
MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
INSTALLING THE PRINTER STATUS MONITOR . . 25
INSTALLING THE SCANNER DRIVER . . . . . . . . . . . 26
INSTALLING THE PS DISPLAY FONTS . . . . . . . . . . 28
CHANGING THE PORT . . . . . . . . . . . . . . . . . . . . . . . 29
1
!mxm503_us_ins.book
1
2 ページ
2009年1月22日 木曜日 午後2時21分
BEFORE INSTALLING THE
SOFTWARE
This chapter describes the software programs that allow you to use the printer and scanner functions of the machine,
the CD-ROMs that contain the software, and the pages where the installation procedures can be found.
CD-ROMS AND SOFTWARE
The software that can be used with the machine is on the CD-ROMs that accompany the machine and the expansion kits.
Before installing the software, make sure that your computer and the machine meet the system requirements described
in "VERIFYING SYSTEM REQUIREMENTS" (page 5).
SOFTWARE CD-ROM
The "Software CD-ROM" that accompanies the machine contains the printer driver and other software. The "Software
CD-ROM" consists of 2 discs.
For users of Windows 98/Me/NT 4.0
The CD-ROM does not include software for Windows 98/Me/NT 4.0.
Contact your dealer or nearest authorized service representative if you want software for Windows 98/Me/NT 4.0.
Disc 1
Software for Windows
• Printer driver
These allow the machine to be used as a printer.
- PCL6 and PCL5e printer driver
The machine supports the Hewlett-Packard PCL6 and PCL5e printer control languages. It is recommended
that you use the PCL6 printer driver. If you have a problem printing from older software using the PCL6
printer driver, use the PCL5e printer driver.
- PS printer driver
The PS printer driver supports the PostScript 3 page description language developed by Adobe Systems
Incorporated.
- PPD driver
The PPD driver enables the machine to use the standard Windows PS printer driver.
☞ WHEN THE MACHINE IS CONNECTED TO A NETWORK (page 9)
☞ WHEN THE MACHINE WILL BE CONNECTED WITH A USB CABLE (page 16)
• Printer Status Monitor (can only be used when the machine is connected to a network)
This allows you to monitor the status of the machine on your computer screen.
☞ INSTALLING THE PRINTER STATUS MONITOR (page 25)
2
!mxm503_us_ins.book
3 ページ
2009年1月22日 木曜日 午後2時21分
CD-ROMS AND SOFTWARE
Disc 2
Software for Windows
• PC-Fax driver
This enables you to send a file from your computer as a fax using the same procedure as when printing the file.
(When the fax option is installed.)
Even if the fax function is not installed, the PC-Fax driver can be updated using the CD-ROM in the Internet fax
expansion kit to enable you to send a file from your computer as an Internet fax in the same way as you print a file.
☞ INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER (page 9)
The following software can be used only when the machine is connected to a network.
• Scanner driver (TWAIN driver)
This allows you to use the scanner function of the machine from a TWAIN-compliant software application.
☞ INSTALLING THE SCANNER DRIVER (page 26)
• Printer Administration Utility
This allows the administrator to monitor the machine and configure machine settings from a computer. To install
and use the Printer Administration Utility, see the Readme file and the manual in PDF format on the "Software
CD-ROM" (Disc 2). The Readme file and manual are in the following folder on the CD-ROM. (Substitute the
letter of your CD-ROM drive for "R" in the following path.)
R:\Sadmin\Documents\EnglishA*
* "EnglishA" in North America. "English" in Europe.
Software for Macintosh
• PPD file
This is the printer description file which enables the machine to be used as a PostScript 3 compatible printer.
The PS3 expansion kit is required to use the machine in a Macintosh environment.
☞ MAC OS X (page 33)
☞ MAC OS 9.0 - 9.2.2 (page 38)
• The PS3 expansion kit is required to use the machine as a printer in a Macintosh environment. In addition,
the machine must be connected to a network. A USB connection cannot be used.
• The scanner driver and PC-Fax driver cannot be used in a Macintosh environment.
3
!mxm503_us_ins.book
4 ページ
2009年1月22日 木曜日 午後2時21分
CD-ROMS AND SOFTWARE
OTHER CD-ROMS
X "PRINTER UTILITIES" CD-ROM that accompanies the PS3 expansion kit
(for Windows/Macintosh)
This contains the display fonts that are used with the PS printer driver.
(Install the PS printer driver and Macintosh PPD file from the "Software CD-ROM".)
☞ INSTALLING THE PS DISPLAY FONTS (page 28)
X "PRINTER UTILITIES" CD-ROM that accompanies the Internet fax
expansion kit (for Windows)
This CD-ROM is used to update the PC-Fax driver on the "Software CD-ROM" so that it can be used to send
Internet faxes (PC-I-Fax function).
If you wish to use the PC-I-Fax function, first install the PC-Fax driver from the "Software CD-ROM" and then run the
installer on this CD-ROM. If the PC-Fax driver is already installed, run only the installer. (There is no need to reinstall
the PC-Fax driver.)
☞ INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER (page 9)
X "Sharpdesk/Network Scanner Utilities" CD-ROM (for Windows)
This contains software that helps you get the most out of the images that you scan on the machine. The software
includes "Sharpdesk", a desktop document management application that enables integrated management of
scanned images and files created using a variety of applications. To use the "Scan to Desktop" scanner function, the
"Network Scanner Tool" must be installed from the CD-ROM.
For the system requirements of the software, see the manual (PDF format) in the "Manual" folder or the Readme file
on the CD-ROM. For the procedures for installing the software, see the "Sharpdesk Installation Guide".
4
!mxm503_us_ins.book
5 ページ
2009年1月22日 木曜日 午後2時21分
VERIFYING SYSTEM REQUIREMENTS
SYSTEM REQUIREMENTS
Before installing the software described in this manual, make sure that your computer satisfies the following
requirements.
Windows
Macintosh*4
Operating system
Windows 98, Windows Me,
Windows NT Workstation 4.0 (Service Pack 5 or later)*1,
Windows 2000 Professional, Windows XP Professional,
Windows XP Home Edition, Windows 2000 Server,
Windows Server 2003, Windows Vista, Windows Server 2008
Mac OS 9.0 to 9.2.2,
Mac OS X v10.2.8,
Mac OS X v10.3.9,
Mac OS X v10.4.11,
Mac OS X v10.5 to 10.5.5
Computer type
IBM PC/AT compatible computer
Equipped with a 10Base-T/100Base-TX/1000Base-T LAN
board or equipped standard with a USB 2.0*2/1.1*3 port.
Display
1024 x 768 dots resolution and 16-bit color or higher is
recommended.
An environment in which any
of the operating systems
listed above can fully operate
(including Macintosh
computers with an Intel
processor).
Other hardware
requirements
An environment that allows any of the above operating
systems to fully operate.
*1 USB is not supported. The scanner driver cannot be installed.
*2 The machine's USB 2.0 port will transfer data at the speed specified by the USB 2.0 (Hi-Speed) standard only if the
Microsoft USB 2.0 driver is preinstalled in the computer, or if the USB 2.0 driver for Windows 2000
Professional/XP/Vista that Microsoft provides through "Windows Update" is installed.
*3 Compatible with models preinstalled with Windows 98, Windows Me, Windows 2000 Professional, Windows XP
Professional, Windows XP Home Edition, Windows 2000 Server, Windows Server 2003, Windows Vista, or Windows
Server 2008, and which are equipped standard with a USB interface.
*4 Cannot be used when the machine is connected with a USB cable. The PC-Fax driver and scanner driver cannot be
used.
• For users of Windows 98/Me/NT 4.0
The CD-ROM does not include software for Windows 98/Me/NT 4.0.
Contact your dealer or nearest authorized service representative if you want software for Windows 98/Me/NT 4.0.
• For users of Windows NT 4.0/2000/XP/Server 2003/Vista/Server 2008
To perform the procedures described in this manual such as installing the software and configuring settings after
installation, administrator authority is required.
5
!mxm503_us_ins.book
6 ページ
2009年1月22日 木曜日 午後2時21分
VERIFYING SYSTEM REQUIREMENTS
SOFTWARE REQUIREMENTS
The following requirements must be met to use the software described in this manual.
Operating
system
environment*1
Windows
Software
Required expansion kits
PCL6 printer driver,
PCL5e printer driver
Can be used in the standard
configuration.
PS printer driver,
PPD driver
PS3 expansion kit
PC-Fax driver*2
Facsimile expansion kit*3
Type of connection*1
Network/ USB
Scanner driver
Printer Status Monitor
Can be used in the standard
configuration.
Printer Administration Utility
Macintosh
Macintosh PPD file
Network only*4 (cannot be
used with a USB connection)
PS3 expansion kit
*1 For the types of computers and operating systems that can run the software, see "SYSTEM REQUIREMENTS" (page 5).
*2 To use the PC-Fax driver, Internet Explorer 4.0 or later must be installed on your computer.
*3 When the Internet fax expansion kit is installed, the PC-Fax driver can be updated using the "PRINTER UTILITIES"
CD-ROM to enable the driver to be used as a PC-I-Fax driver. In this case, the driver can be used without the
facsimile expansion kit.
*4 The scanner driver, Printer Status Monitor, and Printer Administration Utility cannot be used on an IPv6-only network.
6
!mxm503_us_ins.book
7 ページ
2009年1月22日 木曜日 午後2時21分
CONNECTING THE MACHINE
CONNECTING TO A NETWORK
To connect the machine to a network, connect the LAN cable to the machine's network connector. Use a shielded LAN
cable.
After connecting the machine to a network, be sure to configure the IP address and other network settings before
installing the software. (The factory default setting for the IP address is to receive the IP address automatically when the
machine is used in a DHCP environment.)
Network settings can be configured using "Network Settings" in the system settings (administrator) on the machine.
• If the machine is used in a DHCP environment, the IP address of the machine may change. If this happens, printing will not
be possible. This problem can be avoided by using a WINS server or by assigning a permanent IP address to the machine.
• This manual explains how to set up the software in a Windows network environment and in a Macintosh network
environment.
• To use the machine on an IPv6 network, the IPv6 setting must be enabled in "Network Settings" in the system settings
(administrator).
X Checking the IP address of the machine
You can check the IP address of the machine by printing out the "All Custom Setting List" in the system settings. Follow
these steps to print out the "All Custom Setting List".
Press the [SYSTEM SETTINGS] key, touch the [List Print (User)] key, and then touch the [Print] key of "All Custom
Setting List".
CONNECTING THE MACHINE WITH A USB CABLE
(Windows)
The machine can be connected to a computer using a USB cable if the computer is a Windows computer. (The USB
interface on the machine cannot be used in a Macintosh environment.)
The machine and computer should be connected while the printer driver is being installed. If a USB cable is connected
before the printer driver is installed, the printer driver will not be installed correctly. For the procedure for connecting a
USB cable, see "WHEN THE MACHINE WILL BE CONNECTED WITH A USB CABLE" (page 16).
7
!mxm503_us_ins.book
2
8 ページ
2009年1月22日 木曜日 午後2時21分
SETUP IN A WINDOWS
ENVIRONMENT
This section explains how to install the software and configure settings so that the printer and scanner function of the
machine can be used with a Windows computer.
For users of Windows 98/Me/NT 4.0
The CD-ROM does not include software for Windows 98/Me/NT 4.0.
Contact your dealer or nearest authorized service representative if you want software for Windows 98/Me/NT 4.0.
OPENING THE SOFTWARE SELECTION
SCREEN (FOR ALL SOFTWARE)
1
Insert the "Software CD-ROM" into your
computer's CD-ROM drive.
• If you are installing the printer driver or printer status
monitor, insert the "Software CD-ROM" that shows
"Disc 1" on the front of the CD-ROM.
• If you are installing the PC-Fax driver or scanner
driver, insert the "Software CD-ROM" that shows
"Disc 2" on the front of the CD-ROM.
2
5
Read the message in the "Welcome"
window and then click the [Next] button.
6
The software selection screen appears.
Before installing the software, be sure to click the
[Display Readme] button and view the detailed
information on the software.
Click the [Start] button ( ), click
[Computer], and then double-click the
[CD-ROM] icon ( ).
• In Windows XP/Server 2003, click the [start] button,
click [My Computer], and then double-click the
[CD-ROM] icon.
• In Windows 2000, double-click [My Computer] and
then double-click the [CD-ROM] icon.
3
Double-click the [Setup] icon (
).
In Windows Vista/Server 2008, if a message screen
appears asking you for confirmation, click [Allow].
4
The "SOFTWARE LICENSE" window will
appear. Make sure that you understand
the contents of the license agreement
and then click the [Yes] button.
You can show the "SOFTWARE LICENSE" in a
different language by selecting the desired language
from the language menu. To install the software in the
selected language, continue the installation with that
language selected.
8
* The above screen appears when using the
"Disc 1" CD-ROM.
For the steps that follow, see the appropriate page below
for the software that you are installing.
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER
• WHEN THE MACHINE IS CONNECTED TO A NETWORK*
- Standard installation: page 9
- Installation by specifying the machine's address: page 12
- Printing using the IPP function and the SSL
function: page 14
• WHEN THE MACHINE WILL BE CONNECTED WITH A
USB CABLE: page 16
• USING THE MACHINE AS A SHARED PRINTER: page 20
INSTALLING THE PRINTER STATUS MONITOR: page 25
INSTALLING THE SCANNER DRIVER: page 26
* If the machine is being used on an IPv6 network, see
"Installation by specifying the machine's address" (page 12).
!mxm503_us_ins.book
9 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE PRINTER DRIVER /
PC-FAX DRIVER
To install the printer driver or the PC-Fax driver, follow the appropriate procedure in this section depending on whether
the machine is connected to a network or connected by USB cable.
☞ WHEN THE MACHINE WILL BE CONNECTED WITH A USB CABLE (page 16)
WHEN THE MACHINE IS CONNECTED TO A NETWORK
This section explains how to install the printer driver and the PC-Fax driver when the machine is connected to a
Windows network (TCP/IP network).
Supported operating systems: Windows 98/Me/NT 4.0*/2000*/XP*/Server 2003*/Vista*/Server 2008*
* Administrator's rights are required to install the software.
• The PS3 expansion kit is required to use the PS printer driver or the PPD driver.
• To install the PPD driver when Windows 98/Me/NT 4.0 is used, see "USING THE STANDARD WINDOWS PS PRINTER
DRIVER (Windows 98/Me/NT 4.0)" (page 21) and install the driver using the Add Printer Wizard.
• To use the machine as a network printer in Windows NT 4.0, "TCP/IP Protocol" must be installed on your computer. If this
is not installed, see Windows NT 4.0 Help to install "TCP/IP Protocol".
• To print to the machine over the Internet using the IPP function when the machine is installed in a remote location, or to
print using the SSL (encrypted communication) function, see "Printing using the IPP function and the SSL function" (page
14) and install the printer driver or the PC-Fax driver.
• If the machine is connected to an IPv6-only network
The software cannot be installed by detecting the machine's address from the installer. After installing the software as
explained in "Installation by specifying the machine's address" (page 12), change the port as explained in "Changing to a
Standard TCP/IP Port" (page 31).
• The installation procedure in this section is for both the printer driver and the PC-Fax driver, although the explanations are
centered on the printer driver.
X Standard installation
When the software selection screen appears in step 6 of "OPENING THE SOFTWARE SELECTION SCREEN (FOR
ALL SOFTWARE)" (page 8), perform the steps below.
1
Click the [Printer Driver] button.
To install the PC-Fax driver, click the [PC-Fax Driver]
button on the "Disc 2" CD-ROM.
* The above screen appears when using the
"Disc 1" CD-ROM.
9
!mxm503_us_ins.book
10 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER
2
Click the [Standard installation] button.
4
A confirmation window appears. Check
the contents and then click the [Next]
button.
5
When the printer driver selection
window appears, select the printer
driver to be installed and click the
[Next] button.
Click the checkbox of the printer driver to be installed so
that a checkmark (
) appears.
When [Custom installation] is selected, you can change
any of the items below. When [Standard installation] is
selected, the installation will take place as indicated below.
• Machine connection method: LPR Direct Print (Auto
Search)
• Set as default printer: Yes (excluding the PC-Fax driver)
• Printer driver name: Cannot be changed
• PCL printer display fonts: Installed
If you selected [Custom installation], select [LPR
Direct Print (Auto Search)] and click the [Next] button.
If you selected other than [LPR Direct Print (Auto
Search)], see the following pages:
• LPR Direct Print (Specify Address): page 12
• IPP: page 14 • Shared printer: page 20
• Connected to this computer: page 16
3
Printers connected to the network are
detected. Select the machine and click
the [Next] button.
• If the machine is not found, make sure that the
machine is powered on and that the machine is
connected to the network, and then click the
[Re-search] button.
• You can also click the [Specify condition] button and
search for the machine by entering the machine's
name (host name) or IP address.
☞ Checking the IP address of the machine (page 7)
10
• When the PC-Fax driver is being installed, this
screen does not appear. Go to the next step.
• The PS3 expansion kit is required to use the PS
printer driver or the PPD driver.
• The [PPD] checkbox only appears if you are using
Windows 2000/XP/Server 2003/Vista/Server 2008.
!mxm503_us_ins.book
11 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER
6
When you are asked whether or not you
want the printer to be your default
printer, make a selection and click the
[Next] button.
If you are installing multiple drivers, select the printer
driver to be used as the default printer.
If you do not wish to set one of the printer drivers as the
default printer, select [No].
If you clicked the [Custom installation] button in step 2,
the following windows will appear.
• Printer name window
If you wish to change the printer name, enter the
desired name and click the [Next] button.
• Window confirming installation of the display
fonts
To install the display fonts for the PCL printer driver,
select [Yes] and click the [Next] button.
• When the PC-Fax driver is being installed, this
screen does not appear. Go to the next step.
• If you are not installing the PCL printer driver (you
are installing the PS printer driver or the PPD
driver), select [No] and click the [Next] button.
7
9
Click the [Close] button in the window
of step 1.
After the installation, a message prompting you to
restart your computer may appear. If this message
appears, click the [Yes] button to restart your
computer.
This completes the installation.
• After installation, see "CONFIGURING THE PRINTER
DRIVER FOR THE OPTIONS INSTALLED ON THE
MACHINE" (page 22) to configure the printer driver
settings.
• If you installed the PS printer driver or the PPD driver,
the PS display fonts can be installed from the
"PRINTER UTILITIES" CD-ROM that accompanies
the PS3 expansion kit. See "INSTALLING THE PS
DISPLAY FONTS" (page 28).
• If you are using the machine as a shared printer, see
"USING THE MACHINE AS A SHARED PRINTER"
(page 20) to install the printer driver on each of the
client computers.
Follow the on-screen instructions.
Read the message in the window that appears and click
the [Next] button.
Installation begins.
• If you are using Windows Vista/Server 2008
If a security warning window appears, be sure to click
[Install this driver software anyway].
• If you are using Windows 2000/XP/Server 2003
If a warning message regarding the Windows logo
test or digital signature appears, be sure to click the
[Continue Anyway] or [Yes] button.
8
When the installation completed screen
appears, click the [OK] button.
11
!mxm503_us_ins.book
12 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER
X Installation by specifying the machine's address
When the machine cannot be found because it is not powered on or otherwise, installation is possible by entering the
name (host name) or IP address of the machine.
If the machine is being used on an IPv6 network, after you have installed the software as explained below, change the
port as explained in "Changing to a Standard TCP/IP Port" (page 31).
When the software selection screen appears in step 6 of "OPENING THE SOFTWARE SELECTION SCREEN (FOR
ALL SOFTWARE)" (page 8), perform the steps below.
1
Click the [Printer Driver] button.
3
When you are asked how the printer is
connected, select [LPR Direct Print
(Specify Address)] and click the [Next]
button.
4
Enter the name (host name) or IP
address of the machine and click the
[Next] button.
To install the PC-Fax driver, click the [PC-Fax Driver]
button on the "Disc 2" CD-ROM.
* The above screen appears when using the
"Disc 1" CD-ROM.
☞ Checking the IP address of the machine
(page 7)
2
Click the [Custom installation] button.
If the machine is being used on an IPv6 network,
enter any numbers or characters.
12
02_Setup.fm
13 ページ
2009年1月23日 金曜日 午後6時11分
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER
5
6
When the model selection window
appears, select the model name of your
machine and click the [Next] button.
9
• When the PC-Fax driver is being installed, this screen
does not appear. Go to the next step.
When the printer driver selection
window appears, select the printer
driver to be installed and click the
[Next] button.
Click the checkbox of the printer driver to be installed so
that a checkmark (
) appears.
When you are asked if you wish to
install the display fonts, select an
answer and click the [Next] button.
• If you are not installing the PCL printer driver (you are
installing the PS printer driver or the PPD driver),
select [No] and click the [Next] button.
10
Follow the on-screen instructions.
Read the message in the window that appears and click
the [Next] button.
Installation begins.
• If you are using Windows Vista/Server 2008
If a security warning window appears, be sure to click
[Install this driver software anyway].
• If you are using Windows 2000/XP/Server 2003
If a warning message regarding the Windows logo
test or digital signature appears, be sure to click the
[Continue Anyway] or [Yes] button.
• When the PC-Fax driver is being installed, this
screen does not appear. Go to the next step.
11
When the installation completed screen
appears, click the [OK] button.
12
Click the [Close] button in the window
of step 1.
• The PS3 expansion kit is required to use the PS
printer driver or the PPD driver.
• The [PPD] checkbox only appears if you are using
Windows 2000/XP/Server 2003/Vista/Server 2008.
7
Select whether or not you wish the
printer to be your default printer and
click the [Next] button.
If you are installing multiple drivers, select the printer
driver to be used as the default printer.
If you do not wish to set one of the printer drivers as the
default printer, select [No].
8
When the printer name window
appears, click the [Next] button.
If you wish to change the printer name, enter the desired
name and click the [Next] button.
After the installation, a message prompting you to
restart your computer may appear. If this message
appears, click the [Yes] button to restart your
computer.
This completes the installation.
• After installation, see "CONFIGURING THE PRINTER
DRIVER FOR THE OPTIONS INSTALLED ON THE
MACHINE" (page 22) to configure the printer driver
settings.
• If you installed the PS printer driver or the PPD driver,
the PS display fonts can be installed from the
"PRINTER UTILITIES" CD-ROM that accompanies
the PS3 expansion kit. See "INSTALLING THE PS
DISPLAY FONTS" (page 28).
• If the machine is being used on an IPv6 network, enter
any numbers or characters.
13
!mxm503_us_ins.book
14 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER
X Printing using the IPP function and the SSL function
The IPP function can be used to print to the machine over a network using HTTP protocol.
When the machine is in a remote location, this function can be used in place of the fax function to print a higher quality
image than a fax. The IPP function can also be used in combination with the SSL (encrypted communication) function to
encrypt the print data. This enables secure printing with no concern that the data will be leaked to others.
To use the SSL function, configure the "SSL Settings" in the system settings (administrator) of the machine. To configure the
settings, see "7. SYSTEM SETTINGS" in the Operation Guide.
When the software selection screen appears in step 6 of "OPENING THE SOFTWARE SELECTION SCREEN (FOR
ALL SOFTWARE)" (page 8), perform the steps below.
1
Click the [Printer Driver] button.
3
When you are asked how the printer is
connected, select [IPP] and click the
[Next] button.
4
If a proxy server is used, specify the
proxy server and click the [Next]
button.
To install the PC-Fax driver, click the [PC-Fax Driver]
button on the "Disc 2" CD-ROM.
* The above screen appears when using the
"Disc 1" CD-ROM.
2
Click the [Custom installation] button.
14
To specify a proxy server, select [Print via the proxy
server] and then enter the [Address] and [Port number].
!mxm503_us_ins.book
15 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER
5
Enter the machine's URL and click the
[Next] button.
Enter the URL in the following format:
Normal format:
http://<the machine's domain name or IP address>:631*1/ipp
*1 Normally "631" should be entered for the port number.
If the IPP port number has been changed on the
machine, enter the new port number.
When SSL is used:
https://< the machine's domain name or IP address>:<port number*2>/ipp
*2 Normally the port number and the colon ":"
immediately preceding the port number can be
omitted. If the IPP port number for SSL has been
changed on the machine, enter the new port number.
If your computer and the machine are connected to
the same local area network, you can click the
[Search] button to search for the machine. The
machine's URL will appear. Select the URL and click
the [OK] button. You will return to the above screen
and the machine's URL will be automatically entered.
6
Perform steps 5 through 12 on page 13
to continue the installation.
This completes the installation.
• After installation, see "CONFIGURING THE PRINTER
DRIVER FOR THE OPTIONS INSTALLED ON THE
MACHINE" (page 22) to configure the printer driver
settings.
• If you installed the PS printer driver or the PPD driver,
the PS display fonts can be installed from the
"PRINTER UTILITIES" CD-ROM that accompanies
the PS3 expansion kit. See "INSTALLING THE PS
DISPLAY FONTS" (page 28).
15
!mxm503_us_ins.book
16 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER
WHEN THE MACHINE WILL BE CONNECTED WITH A
USB CABLE
Supported operating systems: Windows 98/Me/2000*/XP*/Server 2003*/Vista*/Server 2008*
* Administrator's rights are required to install the software.
• Make sure that a USB cable is not connected to your computer and the machine.
If a cable is connected, a Plug and Play window will appear. If this happens, click the [Cancel] button to close the window
and disconnect the cable.
• The PS3 expansion kit is required to use the PS printer driver or the PPD driver.
• To install the PPD driver when Windows 98/Me is used, see "USING THE STANDARD WINDOWS PS PRINTER DRIVER
(Windows 98/Me/NT 4.0)" (page 21) and install the driver using the Add Printer Wizard.
• To use the port created when the printer driver is installed for fax data transfer, install the printer driver first and then install
the PC-Fax driver.
When the software selection screen appears in step 6 of "OPENING THE SOFTWARE SELECTION SCREEN (FOR
ALL SOFTWARE)" (page 8), perform the steps below.
1
2
Click the [Printer Driver] button.
3
When you are asked how the printer is
connected, select [Connected to this
computer] and click the [Next] button.
4
When you are asked if you wish to
install the display fonts, select an
answer and click the [Next] button.
5
Follow the on-screen instructions.
Click the [Custom installation] button.
Read the message in the window that appears and click
the [Next] button.
When the installation completed screen appears, click
the [OK] button.
• If you are using Windows Vista/Server 2008
If a security warning window appears, be sure to click
[Install this driver software anyway].
• If you are using Windows 2000/XP/Server 2003
If a warning message regarding the Windows logo
test or digital signature appears, be sure to click the
[Continue Anyway] or [Yes] button.
16
!mxm503_us_ins.book
17 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER
6
Click the [Close] button in the window
of step 1.
When a message appears prompting you to connect the
machine to your computer, click the [OK] button.
After the installation, a message prompting you to
restart your computer may appear. If this message
appears, click the [Yes] button to restart your
computer.
7
Connect the machine to your computer
with a USB cable.
(1) Make sure that the machine is powered
on.
(2) Connect the cable to the USB
connector (B type) on the machine.
The USB interface on the machine complies with
the USB 2.0 (Hi-Speed) standard. Please purchase
a shielded USB cable.
8
Installation of the PCL6 printer driver
begins.
When the "Found New Hardware Wizard" appears,
select [Install the software automatically
(Recommended)], click the [Next] button, and follow the
on-screen instructions.
• If you are using Windows Vista/Server 2008
If a security warning window appears, be sure to click
[Install this driver software anyway].
• If you are using Windows 2000/XP/Server 2003
If a warning message regarding the Windows logo
test or digital signature appears, be sure to click the
[Continue Anyway] or [Yes] button.
This completes the installation.
• After installing the printer driver, see "CONFIGURING
THE PRINTER DRIVER FOR THE OPTIONS
INSTALLED ON THE MACHINE" (page 22) to
configure the printer driver settings.
• If you are using the machine as a shared printer, see
"USING THE MACHINE AS A SHARED PRINTER"
(page 20) to install the printer driver on each of the
client computers.
(3) Connect the other end of the cable to
the USB connector (A type) on your
computer.
The machine is found and a Plug and Play window
appears.
17
!mxm503_us_ins.book
18 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER
When installing the PCL5e printer driver, PS printer driver, PPD driver, or PC-Fax driver
Installation is possible even after the USB cable has been connected. When the software selection screen appears in
step 6 of "OPENING THE SOFTWARE SELECTION SCREEN (FOR ALL SOFTWARE)" (page 8), perform the steps
below.
1
Click the [Printer Driver] button.
3
When you are asked how the printer is
connected, select [Connected to this
computer] and click the [Next] button.
4
When the port selection window
appears, select the port that the PCL6
printer driver is using (USB001, etc.)
and click the [Next] button.
5
When the printer driver selection
window appears, remove the [PCL6]
checkmark and select the printer driver
to be installed, and then click the [Next]
button.
To install the PC-Fax driver, click the [PC-Fax Driver]
button on the "Disc 2" CD-ROM.
* The above screen appears when using the
"Disc 1" CD-ROM.
2
Click the [Custom installation] button.
Click the checkbox of the printer driver to be installed so
that a checkmark (
) appears.
• When the PC-Fax driver is being installed, this
screen does not appear. Go to the next step.
• The PS3 expansion kit is required to use the PS
printer driver or the PPD driver.
• The [PPD] checkbox only appears if you are using
Windows 2000/XP/Server 2003/Vista/Server 2008.
18
!mxm503_us_ins.book
19 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER
6
Select whether or not you wish the
printer to be your default printer and
click the [Next] button.
If you are installing multiple drivers, select the printer
driver to be used as the default printer.
If you do not wish to set one of the printer drivers as the
default printer, select [No].
7
When the printer name window
appears, click the [Next] button.
If you wish to change the printer name, enter the desired
name and click the [Next] button.
8
When you are asked if you wish to
install the display fonts, select [No] and
click the [Next] button.
When the PC-Fax driver is being installed, this screen
does not appear. Go to the next step.
9
Follow the on-screen instructions.
Read the message in the window that appears and click
the [Next] button.
Installation begins.
11
Click the [Close] button in the window
of step 1.
After the installation, a message prompting you to
restart your computer may appear. If this message
appears, click the [Yes] button to restart your
computer.
This completes the installation.
• After installation, see "CONFIGURING THE PRINTER
DRIVER FOR THE OPTIONS INSTALLED ON THE
MACHINE" (page 22) to configure the printer driver
settings.
• Make sure that the port of the installed driver is the
same as the port used by the PCL6 printer driver.
The port used by the printer driver of the machine is
indicated by a checkmark on the [Ports] tab of the
printer driver properties window. (In Windows 98/Me,
this is the port selected in [Print to the following port]
on the [Details] tab.)
☞ CHANGING THE PORT (page 29)
• If you installed the PS printer driver or the PPD driver,
the PS display fonts can be installed from the
"PRINTER UTILITIES" CD-ROM that accompanies
the PS3 expansion kit. See "INSTALLING THE PS
DISPLAY FONTS" (page 28).
• If you are using Windows Vista/Server 2008
If a security warning window appears, be sure to click
[Install this driver software anyway].
• If you are using Windows 2000/XP/Server 2003
If a warning message regarding the Windows logo
test or digital signature appears, be sure to click the
[Continue Anyway] or [Yes] button.
10
When the installation completed screen
appears, click the [OK] button.
19
!mxm503_us_ins.book
20 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER
USING THE MACHINE AS A SHARED PRINTER
If you are going to use the machine as a shared printer on a Windows network with the printer driver or the PC-Fax driver
installed on a print server, follow the steps below to install the printer driver or the PC-Fax driver on the client computers.
• Ask your network administrator for the server name and printer name of the machine on the network.
• For the procedure for configuring settings on the print server, see the operation manual or the Help file of the operating
system. The "print server" explained here is a computer that is connected directly to the machine, and "clients" are other
computers connected to the same network as the print server.
• Install the same printer driver on client computers as the printer driver that is installed on the print server.
• If the PPD driver is installed on the print server and the client computers are running Windows 98/Me/NT 4.0, see "USING
THE STANDARD WINDOWS PS PRINTER DRIVER (Windows 98/Me/NT 4.0)" (page 21) to install the printer driver using
the Add Printer Wizard.
When the software selection screen appears in step 6 of "OPENING THE SOFTWARE SELECTION SCREEN (FOR
ALL SOFTWARE)" (page 8), perform the steps below.
1
Click the [Printer Driver] button.
4
To install the PC-Fax driver, click the [PC-Fax Driver]
button on the "Disc 2" CD-ROM.
Select the printer name (configured as a
shared printer).
(1)
(1) Select the printer name (configured as
a shared printer on a print server) from
the list.
* The above screen appears when using the
"Disc 1" CD-ROM.
2
Click the [Custom installation] button.
3
Select [Shared Printer] and click the
[Next] button.
(2)
If you are using Windows 98/Me/NT 4.0/2000/XP/
Server 2003, you can also click the [Add Network
Port] button displayed below the list and select the
printer to be shared by browsing the network in the
window that appears.
(2) Click the [Next] button.
If the shared printer does not appear in the list, check
the settings on the print server.
5
Perform steps 5 through 12 on page 13
to continue the installation.
In the printer driver selection screen, be sure to select the
same type of printer driver as the printer driver installed
on the print server.
This completes the installation.
If you installed the PS printer driver or the PPD driver, the PS
display fonts can be installed from the "PRINTER UTILITIES"
CD-ROM that accompanies the PS3 expansion kit. See
"INSTALLING THE PS DISPLAY FONTS" (page 28).
20
!mxm503_us_ins.book
21 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER
USING THE STANDARD WINDOWS PS PRINTER
DRIVER (Windows 98/Me/NT 4.0)
If the PS3 expansion kit is installed on the machine and you wish to use the standard Windows 98/Me/NT 4.0 PS printer
driver, follow the steps below to install the PPD driver using the Add Printer Wizard.
• The CD-ROM does not include software for Windows 98/Me/NT 4.0.
Contact your dealer or nearest authorized service representative if you want software for Windows 98/Me/NT 4.0.
• If you are using Windows 2000/XP/Server 2003/Vista/Server 2008, you can install the PPD driver from the installer.
• Be sure to view the Readme file (Readme.txt) before installing the PPD driver. The Readme file will be in the [EnglishA]*
folder inside the folder that contains the extracted files after you get the software.
1
2
3
Download the software and save the
extracted files in any folder.
Click the [Start] button, select
[Settings] and then click [Printers].
Double-click the [Add printer] icon.
4
Follow the on-screen instructions.
When you are asked to specify the path of the PPD file,
enter the path as follows.
Operating system
PPD file path
Windows 98/Me
(Folder containing extracted
files)\EnglishA*\PPD\9XME
Windows NT 4.0
(Folder containing extracted
files)\EnglishA*\PPD\NT40
The "Add Printer Wizard" will appear.
After installation, see "CONFIGURING THE PRINTER
DRIVER FOR THE OPTIONS INSTALLED ON THE
MACHINE" (page 22) to configure the printer driver settings.
* "EnglishA" in North America. "English" in Europe.
X Installing the resident font information (Windows 98/Me)
If you have installed the PPD driver on Windows 98/Me and will be using the resident fonts in the machine, you must
install the resident font information. Follow the procedure below to install the resident font information.
• Before installing the resident font information, be sure to install the PPD driver.
• In the event that a resident font cannot be selected in a software application, install the resident font information again.
1
Double-click the folder where the
extracted files are saved when you
installed the PPD driver.
2
Double-click the [EnglishA] folder (the
[English] folder in areas other than the
U.S.), the [PPD] folder, the [9XME]
folder, and then [PFMSetup.exe].
3
Follow the on-screen instructions.
After the resident font information has been installed,
restart your computer.
21
!mxm503_us_ins.book
22 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER
CONFIGURING THE PRINTER DRIVER FOR THE
OPTIONS INSTALLED ON THE MACHINE
After installing the printer driver, you must configure the printer driver settings appropriately for the options that have
been installed and the size and type of paper loaded in the machine. Follow the steps below to configure the printer
driver.
If the PPD driver is installed, see "When the PPD driver is installed" (page 24).
X When the PCL printer driver or PS printer driver is installed
1
Click the [Start] button ( ), click
[Control Panel], and then click [Printer].
3
In Windows 98/Me, click the [Setup] tab and then click
the [Configuration] tab in the window that appears.
• In Windows XP/Server 2003, click the [start] button
and then click [Printers and Faxes].
• In Windows 98/Me/NT 4.0/2000, click the [Start]
button, select [Settings], and then click [Printers].
Click the [Configuration] tab.
4
Click the [Auto Configuration] button.
The settings are automatically configured based on the
detected machine status.
If [Printers and Faxes] does not appear in the [start]
menu in Windows XP, click the [start] button, click
[Control Panel], click [Printers and Other Hardware],
and then click [Printers and Faxes].
2
Open the printer properties window.
(1) Right-click the printer driver icon of the
machine.
(2) Select [Properties].
If the machine is being used on an IPv6 network, you
must configure the options manually as explained in "If
automatic configuration fails" (page 23).
22
!mxm503_us_ins.book
23 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER
5
Configure the image of the machine.
An image of the machine is formed in the printer driver
configuration window based on the options that are
installed.
(1)
(2)
(1) Select the options that are installed on
the machine.
(2) Click the [OK] button.
To cancel the image settings, click the [Cancel]
button.
6
Click the [OK] button in the printer
properties window.
If automatic configuration fails
• You can check the options that are installed and the tray settings by printing out the "All Custom Setting List" in the system
settings of the machine. (However, note that "Input Tray Options" must be set to the number of trays on the machine.)
Follow these steps to print out the "All Custom Setting List": Press the [SYSTEM SETTINGS] key, touch the [List Print
(User)] key, and then touch the [Print] key of "All Custom Setting List".
• Click the [Set Tray Status] button, the [Paper Type Name] button, and the [Set Tandem Print]* button to check the settings
of each.
Set Tray Status: The "Tray Settings" in "Paper Tray Settings" in system settings of the machine are reflected in the
settings shown here. Specify the size and type of paper loaded in each tray.
Paper Type Name: The "Paper Type Registration" settings in "Paper Tray Settings" in the system settings of the machine
are reflected in the settings shown here. If a user type name (1 to 7) was changed, enter the changed
name.
Set Tandem Print*: Enter the setting (the IP address of the slave machine) in "Tandem Connection Setting" in the system
settings (administrator) of the machine.
* "Set Tandem Print" can only be configured when the printer driver is installed using a "Standard installation" or a "Custom
installation" with "LPR Direct Print (Specify Address/Auto Search)" selected.
23
!mxm503_us_ins.book
24 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE PRINTER DRIVER / PC-FAX DRIVER
X When the PPD driver is installed
1
Click the [Start] button ( ), click
[Control Panel], and then click [Printer].
3
Configure the printer driver for the
options installed on the machine.
• In Windows XP/Server 2003, click the [start] button
and then click [Printers and Faxes].
(1)
• In Windows 98/Me/NT 4.0/2000, click the [Start]
button, select [Settings], and then click [Printers].
If [Printers and Faxes] does not appear in the [start]
menu in Windows XP, click the [start] button, click
[Control Panel], click [Printers and Other Hardware],
and then click [Printers and Faxes].
2
Open the printer properties window.
(1) Right-click the printer driver icon of the
machine.
(2) Select [Properties].
(2)
(3)
(1) Click the [Device Settings] tab.
In Windows 98/Me, click the [Device Options] tab.
(2) Configure each item based on the
machine configuration.
The items and the procedures for configuring the
items vary depending on the operating system
version.
(3) Click the [OK] button.
You can check the options that are installed on the
machine by printing out the "All Custom Setting List" in
the system settings. (However, note that "Input Tray
Options" must be set to the number of trays on the
machine.) Follow these steps to print out the "All
Custom Setting List": Press the [SYSTEM SETTINGS]
key, touch the [List Print (User)] key, and then touch
the [Print] key of "All Custom Setting List".
24
!mxm503_us_ins.book
25 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE PRINTER STATUS
MONITOR
Printer Status Monitor is a printer utility that allows general users to check the current status of the machine on their
computer screen, such as whether or not the machine is ready to print. The Printer Status Monitor shows error
information such as paper misfeeds, printer configuration information (whether or not a finisher is installed, etc.) as an
image, the paper sizes that can be used, and the amount of paper remaining.
The Printer Status Monitor cannot be used in the following situations:
• When the machine is connected by a USB cable.
• When printing to the machine using the IPP function.
Supported operating systems: Windows 98/Me/NT 4.0*/2000*/XP*/Server 2003*/Vista*/Server 2008*
* Administrator's rights are required to install the software.
When the software selection screen appears in step 6 of "OPENING THE SOFTWARE SELECTION SCREEN (FOR
ALL SOFTWARE)" (page 8), perform the steps below.
1
Click the [Printer Status Monitor] button.
3
When the installation completed screen
appears, click the [Finish] button.
To have the Printer Status Monitor start automatically
when your computer is started, select the [Add this
program to your Startup folder] checkbox
and click
the [Finish] button.
4
Click the [Close] button in the window
of step 1.
After the installation, a message prompting you to
restart your computer may appear. If this message
appears, click the [Yes] button to restart your
computer.
2
Follow the on-screen instructions.
This completes the installation.
For the procedures for using the Printer Status Monitor, see the Help file. Follow these steps to view the Help file:
Click the Windows [start] button, select [All Programs] ([Programs] in Windows 98/Me/NT 4.0/2000), select [SHARP
Printer Status Monitor] and then select [Help].
25
!mxm503_us_ins.book
26 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE SCANNER DRIVER
The scanner driver (TWAIN driver) can only be used when the machine is connected to a network. When the scanner
driver is installed, PC scan mode of the image send function can be used.
Supported operating systems: Windows 98/Me/2000*/XP*/Server 2003*/Vista*/Server 2008*
* Administrator's rights are required to install the software.
After performing step 1 through step 5 of "OPENING THE SOFTWARE SELECTION SCREEN (FOR ALL
SOFTWARE)" (page 8), continue the steps below.
1
Click the [Scanner Driver (TWAIN)]
button.
This completes the installation. Next, configure the
IP address of the machine in the scanner driver.
When the scanner driver is installed, the "Select Device"
utility is also installed.
The IP address of the machine is configured in the
scanner driver using "Select Device".
5
Click the [start] button, select [All
Programs] ([Programs] in Windows
98/Me/2000), select [SHARP MFP
TWAIN K], and then select [Select
Device].
6
Click the [Search] button.
If you know the IP address, you can click the [Input] key
and enter the IP address without searching.
2
Follow the on-screen instructions.
Read the message in the window that appears and click
the [Next] button.
3
When the finish setup window appears,
click the [OK] button.
4
Click the [Close] button in the window
of step 1.
After the installation, a message prompting you to
restart your computer may appear. If this message
appears, click the [Yes] button to restart your
computer.
26
!mxm503_us_ins.book
27 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE SCANNER DRIVER
7
Select the IP address of the machine
from the "Address" menu and click the
[OK] button.
• Be sure to ask your system administrator (network
administrator) for the IP address of the machine.
• The name (host name) or IP address of the machine
can be directly entered in "Address".
• If the port number used by the scanner function of the
machine has been changed, enter a colon ":" following
the IP address and then enter the port number.
(Normally the port number does not need to be
entered.)
8
Click the [OK] button.
This completes the configuration of the scanner
driver.
27
!mxm503_us_ins.book
28 ページ
2009年1月22日 木曜日 午後2時21分
INSTALLING THE PS DISPLAY FONTS
Fonts that can be used by the PS printer driver are contained on the "PRINTER UTILITIES" CD-ROM that accompanies
the PS3 expansion kit. Install these fonts as needed for the PS printer driver.
1
Insert the "PRINTER UTILITIES"
CD-ROM that accompanies the PS3
expansion kit into your computer's
CD-ROM drive.
6
Click the [PS Display Font] button.
2
Click the [Start] button ( ), click
[Computer], and then double-click the
[CD-ROM] icon ( ).
In Windows Vista/Server 2008, if a message screen
appears asking you for confirmation, click [Allow].
7
Follow the on-screen instructions.
The "SOFTWARE LICENSE" window
will appear. Make sure that you
understand the contents of the license
agreement and then click the [Yes]
button.
8
Click the [Close] button in the screen of
step 6.
• In Windows XP/Server 2003, click the [start] button,
click [My Computer], and then double-click the
[CD-ROM] icon.
• In Windows 98/Me/NT 4.0/2000, double-click [My
Computer], and then double-click the [CD-ROM] icon.
3
4
Double-click the [Setup] icon (
).
You can show the "SOFTWARE LICENSE" in a
different language by selecting the desired language
from the language menu. To install the software in the
selected language, continue the installation with that
language selected.
5
Read the message in the "Welcome"
window and then click the [Next]
button.
28
!mxm503_us_ins.book
29 ページ
2009年1月22日 木曜日 午後2時21分
CHANGING THE PORT
When using the machine in a Windows environment, follow the steps below to change the port when you have changed
the IP address of the machine or have installed the PC-Fax driver when the machine is connected with a USB cable. If
the machine is being used on an IPv6 network, follow the steps 1 to 3 below and see "Changing to a Standard TCP/IP
Port" (page 31) for the remaining steps of the procedure to change the port.
1
Click the [Start] button ( ), click
[Control Panel], and then click [Printer].
3
Adding or changing a port.
• In Windows XP/Server 2003, click the [start] button
and then click [Printers and Faxes].
• In Windows 98/Me/NT 4.0/2000, click the [Start]
button, select [Settings], and then click [Printers].
If [Printers and Faxes] does not appear in the [start]
menu in Windows XP, click the [start] button, click
[Control Panel], click [Printers and Other Hardware],
and then click [Printers and Faxes].
2
Open the printer properties window.
(1) Right-click the printer driver icon of the
machine.
(2) Select [Properties].
(2)
(1)
(1) Click the [Ports] tab.
In Windows 98/Me, click the [Details] tab.
(2) Click the [Add Port] button.
To change to a previously created port such as USB
port, select the desired port (USB001, etc.) from the
list and click the [Apply] button. This changes the port.
29
!mxm503_us_ins.book
4
30 ページ
2009年1月22日 木曜日 午後2時21分
Select [SC2 TCP/IP Port] and then click
the [New Port] button.
5
Create the new port.
In Windows 98/Me, select [Other], [SC2 TCP/IP Port],
and then click the [OK] button.
• The "SC2 TCP/IP Port" is added when the printer
driver is installed using a "Standard installation", or
a "Custom installation" with "LPR Direct Print
(Specify Address/Auto Search)" selected.
• If the printer driver is installed using a "Custom
installation" with "IPP" selected, the [SC-Print2005
Port] is added. If you need to change the printer port
when the machine is connected to an intranet or a
wide area network (WAN) using the IPP function,
select [SC-Print2005 Port], click the [New Port]
button (the [OK] button in Windows 98/Me), and
follow the on-screen instructions to create the port
again.
(1) (2)
(3)
(4)
(1) Enter the machine's IP address.
☞ Checking the IP address of the machine
(page 7)
(2) Make sure that [LPR] is selected.
(3) Make sure that [lp] is entered.
(4) Click the [OK] button.
6
Click the [Close] button in the screen of
step 4.
In Windows 98/Me, this step is not required. Go to the
next step.
7
30
Make sure the created printer port is
selected in the printer properties
window and then click the [Apply]
button.
02_Setup.fm
31 ページ
2009年2月10日 火曜日 午前9時54分
CHANGING THE PORT
X Changing to a Standard TCP/IP Port
If the machine is being used on an IPv6 network, change the port to a port created using the operating system's
"Standard TCP/IP Port".
1
Follow steps 1 to 3 of "CHANGING THE
PORT" (page 29).
2
Select [Standard TCP/IP Port] and then
click the [New Port] button.
3
Click the [Next] button.
4
Enter the machine's IPv6 address in
[Printer Name or IP Address] and click
the [Next] button.
5
Select [Custom] and click the [Settings]
button.
6
Configure the port settings.
(2)
(3)
(1)
(1) Select [LPR].
(2) Enter [lp].
(3) Click the [OK] button.
31
!mxm503_us_ins.book
32 ページ
2009年1月22日 木曜日 午後2時21分
CHANGING THE PORT
7
Click the [Next] button in the screen of
step 5.
8
Click the [Finish] button.
9
Click the [Close] button in the screen of
step 2.
When using a port created with "Standard TCP/IP Port"
When using a port created using "Standard TCP/IP Port" in Windows 2000/XP/Server 2003/Vista/Server 2008, in the
screen that appears after you click the [Configure Port] button in the screen of step 3, make sure the [SNMP Status
Enabled] checkbox is not selected ( ). If the [SNMP Status Enabled] checkbox is selected ( ), it may not be possible
to print correctly.
32
!mxm503_us_ins.book
3
33 ページ
2009年1月22日 木曜日 午後2時21分
SETUP IN A MACINTOSH
ENVIRONMENT
This chapter explains how to install the PPD file to enable printing from a Macintosh and how to configure the printer
driver settings.
☞ MAC OS X: this page
(v10.2.8, v10.3.9, v10.4.11, v10.5 - 10.5.5)
☞ MAC OS 9.0 - 9.2.2: page 38
• The PS3 expansion kit is required to use the machine as a printer in a Macintosh environment. In addition, the
machine must be connected to a network. A USB connection cannot be used.
• The scanner driver and PC-Fax driver cannot be used in a Macintosh environment.
MAC OS X
The explanations of screens and procedures are primarily for Mac OS X v10.4. The screens may vary in other versions of the
operating system.
1
Insert the "Software CD-ROM" into your
computer's CD-ROM drive.
5
Insert the "Software CD-ROM" that shows "Disc 2" on the
front of the CD-ROM.
2
Double-click the [CD-ROM] icon (
the desktop.
3
Double-click the [MacOSX] folder.
) on
Double-click the [MX-PKX] icon (
).
If the "Authenticate" window appears in Mac OS X
v10.2.8, enter the password and click the [OK] button.
6
Click the [Continue] button.
Before installing the software, be sure to read "ReadMe
First". "ReadMe First" is in the [US-English] folder
([English] folder in areas other than the U.S.) in the
[Readme] folder.
4
Double-click the folder corresponding
to the versions of the operating system.
v10.2.8
v10.3.9
v10.4.11
v10.5 10.5.5
33
!mxm503_us_ins.book
34 ページ
2009年1月22日 木曜日 午後2時21分
MAC OS X
7
The License Agreement window will
appear. Make sure that you understand
the contents of the license agreement
and then click the [Continue] button.
11
Select [Utilities] from the [Go] menu.
• If you are using Mac OS X v10.5 to 10.5.5, click
[System Preferences] in the Apple menu ( ) and
select [Print & Fax] ( ). When the screen for adding a
printer appears, click the
button and go to step 14.
A message will appear asking you if you agree to the
terms of the license. Click the [Agree] button.
• If you are using Mac OS X v10.2.8, select
[Applications] from the [Go] menu.
If the license appears in the different language,
change the language in the language menu.
8
Select the hard drive where the PPD file
will be installed and click the [Continue]
button.
Be sure to select the hard drive on which your operating
system is installed.
12
Double-click the [Printer Setup Utility]
icon ( ).
If you are using Mac OS X v10.2.8, double-click the
[Utilities] folder and then double-click the [Print Center]
icon.
If this is the first time you are installing a printer driver
on your computer, a confirmation message will
appear. Click the [Add] button.
9
Click the [Install] button.
Installation begins.
If the "Authenticate" window appears, enter the
password and click the [OK] button.
10
When the message "The software was
successfully installed" appears in the
installation window, click the [Close]
button.
This completes the installation of the software. Next,
configure the printer driver settings.
34
13
Click [Add].
!mxm503_us_ins.book
35 ページ
2009年1月22日 木曜日 午後2時21分
MAC OS X
+
14
Configure the printer driver.
• The procedure for configuring the printer driver varies depending on the operating system version. The procedure for versions
10.4.11 and 10.5 - 10.5.5 and the procedure for other versions are explained separately below.
• The machine can print using the IPP function. If you wish to use the IPP function, see "Printing using the IPP function"
(page 37) to configure the printer driver settings.
v10.4.11, v10.5 - 10.5.5
v10.2.8, v10.3.9
(1)
(1)
(2)
(2)
(3)
(4)
(3)
(4)
(1) Select [AppleTalk].
If multiple AppleTalk zones are displayed, select the
zone that includes the printer from the menu.
(2) Click the machine's model name.
(1) Click the [Default Browser] icon.
• If multiple AppleTalk zones are displayed, select
the zone that includes the printer from the menu.
• If you are using Mac OS X v10.5 to 10.5.5, click
the [Default] icon.
(2) Click the machine's model name.
• The machine's model name usually appears as
[SCxxxxxx]. ("xxxxxx" is a sequence of
characters that varies depending on your model.)
• The PPD file of the machine is automatically
selected.
(3) Make sure that the PPD file of your
model is selected.
The machine's model name usually appears as
[SCxxxxxx]. ("xxxxxx" is a sequence of characters
that varies depending on your model.)
(3) Select the PPD file of the machine.
• If you are using Mac OS X v10.3.9, select [Auto
Select].
• If you are using Mac OS X v10.2.8, select [Sharp]
and click the PPD file of your model.
(4) Click the [Add] button.
If you are using Mac OS X v10.3.9, the PPD file of
the machine is automatically selected and the
peripheral devices installed on the machine are
detected and automatically configured.
(4) Click the [Add] button.
The PPD file of the machine is automatically
selected and the peripheral devices installed on the
machine are detected and automatically configured.
The PPD file is installed in the following folders on the startup disk.
[Library] - [Printers] - [PPDs] - [Contents] - [Resources] - [en.lproj]
35
03_Setup.fm
36 ページ
2009年2月17日 火曜日 午後1時2分
MAC OS X
15
16
Display printer information.
(2)
(1)
Select the machine configuration.
If you selected [Auto Select] in (3) of step 14, the
machine configuration is detected and automatically
configured. Check the configured settings to make sure
they are correct.
(4)
(1)
(1) Click the machine's name.
If you are using Mac OS X v10.5 to 10.5.5, click the
[Options & Supplies] button, click the [Driver] tab
and go to step 16.
(2)
(2) Click [Show Info].
If you are using Mac OS X v10.2.8, select [Show
Info] from the [Printers] menu.
(3)
(1) Select [Installable Options].
If you are using Mac OS X v10.5 to 10.5.5, it does
not appear.
(2) Select the options that are installed on
the machine.
(3) Click the [Apply Changes] button.
If you are using Mac OS X v10.5 to 10.5.5, click the
[OK] button.
(4) Click to close the window.
You can check the options that are installed on the
machine by printing out the "All Custom Setting List" in
the system settings. (However, note that "Input Tray
Options" must be set to the number of trays on the
machine.) Follow these steps to print out the "All
Custom Setting List": Press the [SYSTEM SETTINGS]
key, touch the [List Print (User)] key, and then touch
the [Print] key of "All Custom Setting List".
This completes the configuration of the printer
driver.
36
!mxm503_us_ins.book
37 ページ
2009年1月22日 木曜日 午後2時21分
MAC OS X
X Printing using the IPP function
The machine can print using the IPP function. When the machine is in a remote location, this function can be used in
place of the fax function to print a higher quality image than a fax. If you wish to use the IPP function, follow these steps
to select the PPD file when configuring the printer driver (step 14 on page 35).
v10.4.11, v10.5 - 10.5.5
v10.2.8, v10.3.9
(1)
(1)
(2)
(2)
(3)
(3)
(4)
(4)
(1) Select [IP Printing].
(1) Click the [IP Printer] icon.
If you are using Mac OS X v10.5 to 10.5.5, click the
[IP] icon.
(2) Select [Internet Printing Protocol] in
"Protocol". Enter the address of the
machine (IP address or domain name)
and the queue name.
Enter "ipp" in "Queue".
(3) Select [Sharp] in "Print Using" and
click the PPD file of your model.
If you are using Mac OS X v 10.5 to 10.5.5, select
[Select a driver to use] from "Print Using" and click
the PPD file for your model.
(2) Select [Internet Printing Protocol] in
"Printer Type". Enter the address of the
machine (IP address or domain name)
and the "Queue Name".
• If you are using Mac OS X v10.2.8, enter the
address of the machine (IP address or domain
name) in "Printer's Address".
• Enter "ipp" in "Queue Name".
(3) Select [Sharp] in "Printer Model" and
click the PPD file of your model.
(4) Click the [Add] button.
☞ Checking the IP address of the machine (page 7)
(4) Click the [Add] button.
If you are using Mac OS X v 10.5 to 10.5.5, the
"Installable Options" screen will appear. Make sure
that the settings are correct and click the [Continue]
button.
☞ Checking the IP address of the machine (page 7)
37
!mxm503_us_ins.book
38 ページ
2009年1月22日 木曜日 午後2時21分
MAC OS 9.0 - 9.2.2
If you are using Mac OS 9.0 to 9.2.2, make sure that "LaserWriter 8" has been installed and that the "LaserWriter 8"
checkbox is selected
in "Extensions Manager" in "Control Panels". If not, install it from the system CD-ROM supplied with
your Macintosh computer.
1
Insert the "Software CD-ROM" into your
computer's CD-ROM drive.
8
Select [Chooser] from the Apple Menu.
Insert the "Software CD-ROM" that shows "Disc 2" on the
front of the CD-ROM.
9
Create a printer.
(1)
2
Double-click the [CD-ROM] icon (
the desktop.
3
Double-click the [MacOS] folder.
Before installing the software, be sure to read "ReadMe
First". "ReadMe First" is in the [US-English] folder
([English] folder in areas other than the U.S.) in the
[Readme] folder.
4
Double-click the [Installer] icon (
(2)
) on
).
(3)
(1) Click the [LaserWriter 8] icon.
If multiple AppleTalk zones are displayed, select the
zone that includes the printer.
(2) Click the machine's model name.
5
Click the [Install] button.
The machine's model name usually appears as
[SCxxxxxx]. ("xxxxxx" is a sequence of characters
that varies depending on your model.)
(3) Click the [Create] button.
6
The License Agreement window will
appear. Make sure that you understand
the contents of the license agreement
and then click the [Yes] button.
7
Read the message in the window that
appears and click the [Continue]
button.
Installation of the PPD file begins.
After the installation, a message prompting you to restart
your computer will appear. Click the [OK] button and
restart your computer.
This completes the installation of the software. Next,
configure the printer driver settings.
38
!mxm503_us_ins.book
39 ページ
2009年1月22日 木曜日 午後2時21分
MAC OS 9.0 - 9.2.2
10
13
Select the PPD file.
Select the machine configuration.
(2)
(1)
(1)
(3)
(2)
(1) Select the options that are installed on
the machine.
(2) Select [Options 2] from the menu to
change the screen and continue
selecting the options that have been
installed on the machine.
(1) Click the PPD file for your model.
(2) Click the [Select] button.
(3) Click the [OK] button.
• If the above dialog box does not appear and you
return to the "Chooser" dialog box, follow these
steps to select the PPD file manually.
(1) Make sure that the machine is selected in the
"Select a PostScript Printer" list, and then click
the [Setup] button followed by the [Select PPD]
button.
(2) Select the PPD file for your model and click the
[Open] button.
(3) Click the [OK] button.
You can check the options that are installed on the
machine by printing out the "All Custom Setting List" in
the system settings. (However, note that "Input Tray
Options" must be set to the number of trays on the
machine.) Follow these steps to print out the "All
Custom Setting List": Press the [SYSTEM SETTINGS]
key, touch the [List Print (User)] key, and then touch
the [Print] key of "All Custom Setting List".
• The PPD file is installed in the [Printer Descriptions]
folder in the [Extensions] folder.
11
12
Make sure that the machine is selected
in the "Select a PostScript Printer" list
and then click the [Setup] button.
Click the [Configure] button.
To automatically configure the settings based on the
installed machine options that are detected, click the
[Auto Setup] button.
14
Click the [OK] button in the window of
step 12 to close the window.
15
Click the close box (
"Chooser".
) to close the
This completes the configuration of the printer
driver.
Installing the screen fonts
The screen fonts for Mac OS 9.0 - 9.2.2 are contained in
the [Font] folder of the "PRINTER UTILITIES" CD-ROM
that accompanies the PS3 expansion kit. Copy the fonts
that you wish to install to the [System Folder] of the
startup disk.
If you experience problems that may be due to the
installed screen fonts, immediately delete the installed
fonts from the system.
39
!mxm503_us_ins.book
4
40 ページ
2009年1月22日 木曜日 午後2時21分
TROUBLESHOOTING
WHEN INSTALLATION WAS NOT
SUCCESSFUL
This section provides solutions to possible installation problems. See the following table of contents to locate the
appropriate page for your question or problem.
• The software cannot be installed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
• The machine is not detected (when connected to a network). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
• The plug and play screen does not appear (USB connection in Windows). . . . . . . . . . . . . . . . . . . . . . 41
• The printer driver is not installed correctly by plug and play (USB connection in Windows). . . . . . . . . 42
• The printer driver cannot be installed (Windows 2000/XP/Server 2003) . . . . . . . . . . . . . . . . . . . . . . . 42
Problem
The software cannot
be installed.
The machine is not
detected (when
connected to a
network).
40
Point to check
Solution
Is there sufficient free space on your
hard drive?
Delete any unneeded files and applications to increase
free space on your hard drive.
Are you using an operating system that
is not supported?
Make sure that the software can run on your operating
system.
For detailed information on installation requirements for
each software program in Windows, click the [Display
Readme] button in the installer.
In a Macintosh environment, this can be checked in
"ReadMe First" in the [US-English] folder ([English]
folder in areas other than the U.S.) in the [Readme]
folder of the "Software CD-ROM".
Is the IP address of the machine
configured?
If the IP address of the machine is not configured, the
machine will not be detected. Make sure that the IP
address is configured correctly in "Network Settings" in
the machine's system settings (administrator).
➞ System Settings (Administrator) > "Network Settings"
Is your computer connected to the same
network as the machine?
Windows:
If the machine and your computer are not connected
to the same local area network, the machine will not
be detected. If the two are connected to different
sub-networks, click the [Specify condition] button and
enter the machine's name (host name) or IP address
to search for the machine.
Macintosh:
If multiple AppleTalk zones exist, select the zone to
which the machine is connected from the menu.
!mxm503_us_ins.book
41 ページ
2009年1月22日 木曜日 午後2時21分
WHEN INSTALLATION WAS NOT SUCCESSFUL
Problem
The machine is not
detected (when
connected to a
network).
The plug and play
screen does not
appear (USB
connection in
Windows).
Point to check
Solution
Is the machine power on?
If the machine is powered off, it will not be detected.
Switch on the main power switch and the [POWER] key
( ) in that order. (In Windows, search again after
powering on the machine.)
Is your computer connected correctly to
the machine?
Make sure that the cable is connected securely to the
LAN connectors on your computer and the machine.
Check the connections at the hub as well.
☞ CONNECTING TO A NETWORK (page 7)
Is the machine power on?
When a USB cable is connected, make sure the power
of the machine is "ON" and then connect a USB cable to
the machine. When the machine is not powered on,
switch on the main power switch and the [POWER] key
( ) in that order.
Can your computer use a USB
connection?
Check your computer whether or not a USB interface
can be used on the Device Manager in your computer.
(For information on "Device Manager", see Help in
Windows.)
If USB can be used, your controller chipset type and
root hub will appear in "Universal Serial Bus controllers"
in "Device Manager". (The items that appear will vary
depending on your computer.)
If these two items appear, USB should be useable. If a
yellow exclamation point appears next to "Universal
Serial Bus controllers" or the two items do not appear,
refer to your computer manual or check with the
manufacturer of your computer to enable USB and then
reinstall the printer driver.
41
!mxm503_us_ins.book
42 ページ
2009年1月22日 木曜日 午後2時21分
WHEN INSTALLATION WAS NOT SUCCESSFUL
Problem
The printer driver is
not installed correctly
by plug and play (USB
connection in
Windows).
Point to check
Solution
In Windows 2000/XP/Server 2003/Vista/Server 2008, if
the machine was connected to your computer with a
USB cable before the printer driver was installed from
the installer, check if information on the unsuccessful
installation remains in "Device Manager". (For
information on "Device Manager", see Help in
Windows.)
If the model name of the machine appears in "Other
devices" in "Device Manager", delete it, restart your
computer, and install the printer driver again.
Did you connect the machine to your
computer before installing the printer
driver?
X The printer driver cannot be installed (Windows 2000/XP/Server 2003)
If the printer driver cannot be installed on Windows 2000/XP/Server 2003, follow the steps below to check your
computer settings.
1
Click the [start] button and then click
[Control Panel].
In Windows 2000, click the [Start] button, point to
[Settings], and click [Control Panel].
2
4
Check the settings in "What action do
you want Windows to take?" ("File
signature verification" in Windows 2000).
Click [Performance and Maintenance]
and then [System].
In Windows 2000, double-click the [System] icon.
3
Click the [Hardware] tab and then the
[Driver Signing] button.
If [Block] is selected, the printer driver cannot be installed.
Select [Warn] and install the printer driver again.
42
!mxm503_us_ins.book
43 ページ
2009年1月22日 木曜日 午後2時21分
REMOVING THE SOFTWARE
To remove the printer driver or software installed using the installer, follow the steps below.
Windows
Mac OS X
1
1
Click the [start] button and then click
[Control Panel].
To show the printer list, see step 11 and 12 of "MAC OS
X" (page 33).
In Windows 98/Me/NT 4.0/2000, click the [Start] button,
point to [Settings], and click [Control Panel].
2
Click [Uninstall a program].
2
• In Windows 98/Me/NT 4.0/2000, double-click the
[Add/Remove Programs] icon.
Select the program or driver that you
wish to delete.
3
Restart your computer.
Delete the installation information.
The installation information file has been copied to the
following folder on the startup disk.
[Library] - [Receipts]
Delete the [MX-PKX.pkg] file from this folder.
For more information, see the manual for the operating
system or Help.
4
Delete the PPD file.
The PPD file has been copied to the following folder on
the startup disk.
[Library] - [Printers] - [PPDs] - [Contents] - [Resources] [en.lproj]
Delete the PPD file of the machine from this folder.
• In Windows XP/Server 2003, click [Add or Remove
Programs].
3
Delete the printer that uses the
machine's PPD file from the printer list.
Mac OS 9.0 - 9.2.2
After deleting the icon of the printer that uses the
machine's PPD file from the desktop, follow the steps
below.
1
Insert the "Software CD-ROM" into your
CD-ROM drive.
Insert the "Software CD-ROM" that shows "Disc 2" on the
front of the CD-ROM.
2
Double-click the [CD-ROM] icon (
the desktop and double-click the
[MacOS] folder.
) on
3
Double-click the [Installer] icon (
).
4
Select [Remove] in the Install menu and
click the [Remove] button.
43
!mxm503_us_ins.book
44 ページ
2009年1月22日 木曜日 午後2時21分
!mxm503_us_ins.book
45 ページ
2009年1月22日 木曜日 午後2時21分
00-1(Cover4)_Setup.fm 42 ページ
2009年2月17日 火曜日 午後1時8分
MX-M283N/M363N/M453N/M503N Software Setup Guide
This manual has been printed using a vegetable-based soy oil ink
to help protect the environment.
PRINTED IN CHINA
2009B
KS1
TINSE4370FCZZ
Download PDF

advertising