Williams 2056511.9 Owner`s manual

Williams 2056511.9 Owner`s manual
Owner’s Manual
Save this manual for future reference.
Blue Flame Unvented
Gas Heater
Model Numbers:
0656542.9; 1056512.9; 1056542.9, 2056512.9; 3056512.9
FOR USE WITH NATURAL GAS ONLY
6,000 and 10,000
Btu/hr. Model
20,000
Btu/hr. Model
Model Numbers:
0656541.9; 1056511.9; 1056541.9, 2056511.9; 3056511.9
FOR USE WITH PROPANE GAS ONLY
READ THIS INSTRUCTION MANUAL CAREFULLY BEFORE
YOU INSTALL YOUR NEW WILLIAMS WALL HEATER.
WARNING: If the information in this manual is
not followed exactly, a fire or explosion may
result causing property damage, personal
injury or loss of life.
30,000
Btu/hr. Model
Unvented room heaters are for installation in SINGLE FAMILY
TYPE DETACHED RESIDENCES ONLY, and the installation is
limited to ONE (1) unit per residence. Unvented room heaters are
only to be used as supplementary heat and NOT AS PRINCIPAL
SOURCE OF HEAT for the room in which the unit is installed.
Unvented room heaters are for installation in rooms having space
which shall limit the appliance input to a maximum of "20 BTUH"
per cubic foot of room space. Unvented room heaters are NOT
TO BE USED IN BEDROOMS, MOBILE HOMES, TRAILERS
AND RECREATIONAL VEHICLES.
EXCEPTION: If local codes permit, models 0656542.9 and
0656541.9 may be used in a bathroom, bedroom or mobile
home. Models 1056511.9, 1056512.9, 1056541.9 and
1056542.9 may be used in a bedroom or mobile home
(check local codes prior to installation).
In the Canadian provinces of British Columbia and Manitoba,
unvented heaters shall be limited to those having INPUT
RATINGS OF UP TO 25,000 BTU PER HOUR MAXIMUM.
Unvented room heaters are NOT FOR COMMERCIAL OR
INDUSTRIAL USE.
Installation must conform
to local codes. ln the
absence of local codes,
installation must conform
with the current:
National Fuel Gas Code
ANSI Z223.1
and
ANSI z21.11.2
This is an unvented gas-fired heater. It uses air (oxygen) from the
room in which it is installed. Provisions for adequate combustion
and ventilation air must be provided. Refer to page 7.
– Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
– What to do if you smell gas:
• Open all windows.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Extinguish any open flame.
• Immediately call your gas supplier from a
neighbor’s phone. Follow gas supplier’s
instructions; call the fire department.
– If you cannot, installation and service must be
performed by a qualified installer, service
agency or the gas supplier.
WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause injury
or property damage. Refer to this manual. For
assistance or for additional information consult a
qualified installer, service agency or the gas
supplier.
WARNING: Do not install any of these heaters
(Natural or L.P. Gas) in mobile homes, trailers or
recreational vehicles.
1
Williams Furnace Co.
 250 West Laurel Street  Colton, California 92324 U.S.A.
Warranty & Installation Record – 2
Warranty
The Manufacturer, Williams Furnace Co., warrants this wall heater or heater to the original purchaser under the following conditions:
LIMITED ONE-YEAR WARRANTY
1. Any part thereof which proves to be defective in material or workmanship within one year from date of original purchase for use will be repaired or replaced
at the Manufacturer’s option, FOB, its factory.
2. No liability is assumed by the Manufacturer for removal or installation labor costs, nor for freight or delivery charges.
LIMITED EXTENDED WARRANTY
1. In addition to the above limited one-year warranty on the complete unit, any combustion chamber which burns out or rusts under normal installation, use and service
conditions during a period of nine years following expiration of the one-year warranty period will be exchanged for a like or functionally similar part.
2. No liability is assumed by the Manufacturer for removal or installation labor costs, nor for freight or delivery charges.
LIMITATIONS
1. THIS LIMITED WARRANTY IS THE ONLY WARRANTY MADE BY THE MANUFACTURER, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE ARE LIMITED TO THE SAME ONE YEAR TERM AS THE EXPRESS WARRANTY. UNDER NO CIRCUMSTANCES SHALL THE
MANUFACTURER BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, SPECIAL OR CONTINGENT DAMAGES OR EXPENSES ARISING DIRECTLY OR INDIRECTLY
FROM ANY DEFECT IN THE PRODUCT OR ANY COMPONENT OR FROM THE USE THEREOF THE REMEDIES SET FORTH HEREIN ARE THE EXCLUSIVE
REMEDIES AVAILABLE TO THE USER AND ARE IN LIEU OF ALL OTHER REMEDIES.
Some states do not allow limitation on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you.
2. This warranty does not include any charge for labor or installation.
3. This warranty does not extend to painted surfaces nor to damage or defects resulting from accident, alteration, misuses or abuse or improper installation.
4. This warranty does not cover claims which do not involve defective workmanship or materials.
DUTIES OF THE CONSUMER
1. The heating equipment must be installed by a qualified installer and operated in accordance with the installation and homeowner’s instructions furnished with the
equipment.
2. Any travel, diagnostic costs, service labor, and labor to repair the defective unit will be the responsibility of the owner.
3. A bill of sale, cancelled check, payment record or permit should be kept to verify purchase date to establish the warranty period.
4. Have the installer enter the requested information in the space below.
GENERAL
1. The Manufacturer neither assumes nor authorizes any person to assume for it any other obligation or liability in connection with said equipment.
2. Service under this warranty should be obtained by contacting your dealer. Provide the dealer with the model number, serial number, and purchase date verification.
3. If, within a reasonable time after contacting your dealer, satisfactory service has not been received, contact: Customer Service Department, 250 West Laurel Street,
Colton, CA 92324 for assistance.
4. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
Installation Record
Original Purchaser____________________________________________________________________________________________
Model No. ______________________________________________________________ Serial No. ___________________________
Address ____________________________________________________________________________________________________
City and State ___________________________________________________________ Zip ________________________________
Dealer _____________________________________________________________________________________________________
Address ____________________________________________________________________________________________________
City and State ___________________________________________________________ Zip ________________________________
Installation date _______________ Signed by ______________________________________________________________________
(Dealer or authorized representative who certifies that this appliance in accordance with manufacturer’s instructions and local codes.)
2
Contents
Your Williams Warranty .................................................................2
Installation Record.........................................................................2
Table of Contents ..........................................................................3
Safety Rules ..................................................................................4
Introduction................................................................................ 5-6
Provisions for Adequate Combustion and Ventilation Air ..............7
Installing Your Heater .............................................................. 8-12
Operating Your Heater .......................................................... 12-13
Caring for Your Heater ................................................................14
Troubleshooting Your Heater ................................................ 15-16
Order Replacement Parts ...................................................... 16-23
Installing and Operating Your Blower Accessory.........................24
Installing Your Floor Base Accessory …. ....................................25
Additional References ........................................................... 26-27
Service Hints ...............................................................................28
3
Safety Rules
WARNING: Read these rules and the instructions
carefully.
Failure to follow these rules and
instructions could cause a malfunction of the
heater. This could result in death, serious bodily
injury and/or property damage.
2.
INSTALLATION MUST CONFORM TO LOCAL CODES. IN THE
ABSENCE OF LOCAL CODES, INSTALLATION MUST
CONFORM TO THE NATIONAL FUEL GAS CODE, ANSI Z223.1.
4.
INSTALLATION AND REPAIR SHOULD BE DONE BY A
QUALIFIED SERVICE TECHNICIAN.
THE APPLIANCE
SHOULD BE INSPECTED BEFORE USE AND AT LEAST
ANNUALLY BY A PROFESSIONAL SERVICE TECHNICIAN.
MORE FREQUENT CLEANING MAY BE REQUIRED DUE TO
EXCESSIVE LINT FROM SOME CARPETING, BEDDING
MATERIAL, ETC.
IT IS IMPERATIVE THAT CONTROL
COMPARTMENTS, BURNERS AND CIRCULATING AIR
PASSAGEWAYS OF THE APPLIANCE BE KEPT CLEAN.
5.
6.
3.
7.
8.
SEE CARBON MONOXIDE WARNING ON PAGE 12.
9.
YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED
WHEN THEY ARE IN THE SAME ROOM WITH THE
APPLIANCE.
ANY SAFETY SCREEN, GUARD OR PARTS REMOVED FOR
SERVICING AN APPLIANCE MUST BE REPLACED PRIOR
TO OPERATING THE APPLIANCE TO AVOID PROPERTY
DAMAGE, BODILY INJURY OR DEATH.
CHILDREN AND ADULTS SHOULD BE ALERTED TO THE
HAZARD OF HIGH SURFACE TEMPERATURE AND SHOULD
STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION.
DUE TO HIGH TEMPERATURES, THE APPLIANCE SHOULD
BE LOCATED OUT OF TRAFFIC AND AWAY FROM
FURNITURE AND DRAPERIES.
WARNING: Any change to this heater or its
controls could cause injury or death.
1.
10.
11.
12.
13.
14.
15.
16.
Be sure the heater is for type of gas to be used. Do not
change it to use with other gases. Unsafe operation could
result and could cause bodily injury and death.
It is prohibited to install the heater in a bedroom, trailer or
recreational vehicle/mobile home, etc (see exceptions on the
front page). If installed in a garage or basement, heater must
be a minimum of 24" above the floor.
Use joint compound (pipe dope) on threaded joints of gas
piping that is resistant to the action of liquefied petroleum
gas.
Use only ground joint unions in gas piping.
Install a manual shutoff valve and union ahead of the controls
so that the controls and heater may be removed for servicing,
if necessary.
Include a 1/8 NPT plugged tapping accessible for test gauge
connection immediately upstream of the gas supply
connection to the heater.
Never test for gas leaks with an open flame. Use soap suds
to check all gas connections. This will avoid the possibility of
fire or explosion.
Turn off heater and let cool before servicing. Only a qualified
service person should service and repair this heater.
DO NOT PLACE CLOTHING OR OTHER FLAMMABLE
MATERIAL ON OR NEAR THE APPLIANCE.
DO NOT modify or alter the heater in any way.
Clean the heater and periodically inspect the pilot and burner
flame as described in the maintenance section of this manual.
Disconnect the heater during supply line pressure testing.
Follow the lighting and operating procedures given in this
manual.
Since the vent-free gas heaters may easily increase the
amount of humidity in the room, the larger the burner size the
more humidity present. This can cause excessive moisture
accumulation on windows and other surfaces.
If L.P. gas is required, the L.P. supply tank must be placed
outside the house. It must be installed in a well ventilated
area away from the house. The distances must be placed as
prescribed by the law. Check local and state codes and laws
in order to comply with proper safety requirements.
Use only manufacturer’s replacement parts. Use of any other
parts could cause injury or death.
WARNING:
Do not use this unvented room heater if any part has been under water. Immediately call a qualified service technician to inspect the
unvented room heater and to replace any part of the control system and any gas control which has been under water.
4
Introduction – 5
Introduction
Please read our instructions before you install and use your heater. This will help you obtain the full value from this heater. It could
help you avoid needless service costs, if the answer to the problem is found within this instruction manual. If the answer is not found,
call our Customer Service Department at (909) 825-0993 before returning the heater to your supplier.
Today's homes are built more energy efficient than ever. New materials, increased insulation and new construction methods help
reduce heat loss in homes. Homeowners weather strip and caulk around windows and doors to keep the cold air out and the warm air
in. During heating months, homeowners want their homes as airtight as possible. While it is good to make your home energy efficient,
your home needs to breathe. Fresh air must enter your home. All fuel-burning appliances need fresh air for proper combustion and
ventilation.
Basic Description
Unvented heaters are shipped ready to install. No electric power
is needed for the heater except when the optional accessory
blower is used. Then, a standard three prong receptacle
(electrical outlet) is needed near the heater.
Always consult your local heating or plumbing inspector, building
department or gas utility company regarding regulations, codes or
ordinances which apply to the installation of an unvented heater.
The heater contains a single, multi-slot gas burner.
Combustion air is drawn to the heater from the room in which it is
installed. It must receive enough air to enable it to operate
properly. See page 7 of this instruction manual for more
information.
Convection causes room air to circulate from the floor upward
along the front, back and sides of the heater, and then back to the
room.
The heater cabinet is built of heavy-gauge steel treated for
corrosion resistance and has an enamel paint finish. The heater
controls are located on the top of the cabinet. All models are
equipped with AGA/CGA listed gas valves and pilots.
Piezo Ignition System
This unit has a piezo igniter. This system requires no matches,
batteries, or other sources to light the heater.
Thermostatic Heat Control
Thermostat models have a thermostat sensing bulb and a control
valve. This results in the greatest heat comfort. This can also
result in lower gas bills.
Safety Device
This unit has a pilot with an Oxygen Depletion Sensor shutoff
system (ODS). The ODS/pilot is a required feature for unvented
room heaters. The ODS/pilot shuts off the heater if there is not
enough fresh air. When the normal oxygen content
(approximately 21 %) is reduced to 18%, the pilot and main
burner will turn off and cannot be relighted. When the pilot flame
is extinguished by wind or interruption of gas supply, it will also
turn off. Relighting is possible in this condition.
Basic Materials Needed
Pipe and fittings to make connections to heater.
Black iron gas pipe and fittings - 1/2".
Pipe Joint Compound resistant to L.P. gases.
Electrical supplies only required if accessory blower is being
installed.
Electrical wiring supplies as needed.
Minimum wire size is #14 gauge copper.
Basic Tools Needed
Pipe Wrenches
Screwdriver
6 ft. folding rule or tape
Level
Pipe cutting and threading tools
Gloves and safety glasses
Helpful Installation Information
The following booklets will help you in making the installation:
ANSI/NFPA 70, or current edition “National Electrical Code”. In Canada: CSA C22.1 Canadian Electrical Code.
American National Standard Z223.1 or current edition “National Fuel Gas Code”, also known as NFPA 54. In Canada: CAN/CGAB149.
Obtain from the American National Standard Institute, Inc., 1430 Broadway, New York NY 10018.
5
Introduction
Optional Accessories
Floor Base Model 4287, may be used with models:
2056512.9; 2056511.9
Blower Model 2205, equipped with a thermostat control may be
used with models: 2056512.9; 2056511.9; 3056512.9; 3056511.9
Model 4288 may be used with models:
3056512.9; 3056511.9
Model 2206 equipped with a manual control may be used with
models: 2056512.9; 2056511.9; 3056512.9; 3056511.9
Specifications
6
Model
No.
Btu/hr.
0656542.9
6,000
7"W.C
Min. Gas
Inlet
Pressure
5"W.C.
0656541.9
1056542.9
1056541.9
1056512.9
1056511.9
2056512.9
2056511.9
3056512.9
3056511.9
6,000
10,000
10,000
10,000
10,000
20,000
20,000
30,000
30,000
13"W.C
7"W.C
13"W.C
7"W.C
13"W.C
7"W.C
13"W.C
7"W.C
13"W.C
11"W.C.
5"W.C.
11"W.C.
5"W.C.
11"W.C.
5"W.C.
11"W.C.
5"W.C.
11"W.C.
Max. Supply Pressure
Manifold
Pressure
Manifold
Dimensions
Weight
4"W.C.
5 1/4X13 3/4X18 1/8
15
10"W.C.
4"W.C.
10"W.C.
4"W.C.
10"W.C.
4"W.C.
10"W.C.
4"W.C.
10"W.C.
5 1/4X13 3/4X18 1/8
5 1/4X13 3/4X18 1/8
5 1/4X13 3/4X18 1/8
5 1/4X13 3/4X18 1/8
5 1/4X13 3/4X18 1/8
6 7/8X18 5/8X23 1/8
6 7/8X18 5/8X23 1/8
6 7/8X26 1/8X23 1/8
6 7/8X26 1/8X23 1/8
15
15
15
15
15
18
18
25
25
Provisions for Adequate Combustion and
Ventilation Air
Supplying Adequate Ventilation
The following information will help you provide adequate
ventilation.
Unusually tight construction is defined as construction where:
a. walls and ceilings exposed to the outside atmosphere
have a continuous water vapor retarder with a rating
-11
2
of one perm (6 x 10 kg per pa-sec-m ) or less with
openings gasketed or sealed and
b. weather stripping has been added on openable
windows and doors and
c. caulking or sealants are applied to areas such as
joints around window and door frames, between sole
plates and floors, between wall-ceiling joints, between
wall panels, at penetrations for plumbing, electrical
and gas lines and at other openings.
If your home meets all of the three criteria above, you must
provide additional fresh air.
WARNING: If the area in which the heater may
be operated is of unusually tight construction,
provide adequate combustion and ventilation air
by one of the methods described in the National
Fuel Gas Code, ANSIZ223.1, Section 5.3 or
applicable local codes.
*Do not include direct-vent gas appliances. Direct-vent
draws combustion air from the outdoors and vents to the
outdoors.
4.
Compare the maximum Btu/hr the space can support with
the actual amount of Btu/hr used.
__________Btu/hr (maximum the space can suppot)
__________Btu/hr (actual amount of Btu/hr used)
Example: 63,360 Btu/hr (maximum the space can suppot)
69,000 Btu/hr (actual amount of Btu/hr used)
If you must provide additional fresh air. Your options are
as follows:
A. Rework worksheet, adding the space of an adjoining
room. If the extra space provides necessary air,
remove door to adjoining room or add ventilation grills
between rooms. See Ventilation Air From Inside
Building.
B. Install a lower Btu/hr heater, if lower Btu/hr size
makes room unconfined.
If the actual Btu/hr used is less than the maximum Btu/hr
the space can support, you will need no additional fresh air
ventilation.
Ventilation Air from Inside Building
Space: Includes the room in which you will install heater plus
any adjoining rooms with doorless passageways or ventilation
grills between the rooms.
This fresh air would come from an adjoining room. When
ventilating to an adjoining room, you must provide two
permanent openings: one within 12" of the ceiling and one
within 12" of the floor on the wall connecting the two spaces.
You can also remove door into adjoining room.
1.
Ventilation Air from Outdoors
Determining If You Need Additional Fresh Air.
Determine the volume of the space (length x width x
height). Length x Width x Height=_______cu. ft. (volume
of space)
Example: Space size 22 ft. (length) x 18 ft. (width) x 8 ft.
(ceiling height) = 3,168 cu. ft. (volume of space)
If additional ventilation to adjoining room is supplied with
grills or openings, add the volume of these rooms to the
total volume of the space.
2.
Divide the space volume by 50 cubic feet to determine the
maximum Btu/hr the space can support, (volume of space)
divided by 50 cu. ft. = (Maximum Btu/hr the space can
support.
Example: 3,168 cu. ft. (volume of space) divided by 50
cu. ft. = 63.36 or 63,360 (maximum Btu/hr the space can
support)
3.
Add the Btu/hr of all fuel burning appliances in the space.
Gas water heater* _____________Btu/hr
Gas heater
_______________Btu/hr
Vented gas heater ______________Btu/hr
Gas fireplace logs __________Btu/hr
Other gas appliances* +__________Btu/hr
Total
=_____________Btu/hr
Example: Gas Heater
Vent-free heater
Total
30,000 Btu/hr
+39,000 Btu/hr
=69,000Btu/hr
Provide extra fresh air by using ventilation grills or ducts. You
must provide two permanent openings: one within 12" of the
ceiling and one within 12" of the floor. Connect these items
directly to the outdoors or spaces open to the outdoors. These
spaces include attics and crawl spaces. Follow the National
Fuel Gas Code NFPA 541 ANSI 2223. 1, Section 5.3, Air for
Combustion and Ventilation for required size of ventilation grills
or ducts.
IMPORTANT. Do not provide openings for inlet or outlet air into
attic if attic has a thermostat-controlled power vent. Heated air
entering the attic will activate the power vent.
In Canada:
When combustion air supply is for the unvented room heater
only, it shall be sized at the rate of one (1) square inch per
1000 Btu/hr (.29KW) from outdoors. However, combustion air
is acceptable when available from the principal heat source
and sized to the current CAN/CGA B149.1 or .2 requirements.
Where unvented equipment is installed in an area separated
from a combustion air supply by a door, then permanent
openings, grilles or louvers shall be provided. One shall be
within 18 inches (46 cm) from the ceiling, and one 18 inches
(46 cm) from the floor, sized to one (1) square inch per 1000
Btu (0.29 KW) to allow free movement of air with the source of
combustion air supply.
7
Installing Your Heater
Unpack Your Unvented Gas Heater
The heater is shipped assembled. The cabinet must be removed
for the heater installation.
1.
2.
3.
Open carton and carefully lift out heater.
Stand heater upright.
Hardware included with heater:
(2) metal mounting brackets
(4) screws
(4) plastic anchors
(1) mounting bracket paper template
4.
Properly dispose of shipping material.
NOTE
Check the burner rating plate, located inside the cabinet on the
bottom, to make sure your heater is equipped to operate on the
type of gas available (either Natural or L.P. Gas). DO NOT
convert the heater from Natural Gas to L.P. Gas or from L.P. Gas
to Natural Gas.
Locating Unvented Gas Heater
Consider the following points before attempting to install the
heater:
deciding where you install this heater. The heater must
have enough fresh air suitable for proper combustion.
1.
This heater is designed to be mounted on a wall. It can
also be located on the floor, away from the wall, using an
optional floor mounting stand.
4.
For proper combustion of the heater, you may need to
provide one or more fresh air openings to the room where
the heater is located.
2.
Select a location for the heater that will provide exposure
of the radiant surface to the room, but will not be subjected
to accidental contact. Adequate clearance must be
available around the air opening.
5.
3.
Be sure to read the section "Provisions for Adequate
Combustion and Ventilation Air" requirements before
This heater creates warm air currents that move heat to
wall surfaces next to heater. Installing the heater next to
vinyl or cloth wall coverings or operating heater where
impurities in the air (such as tobacco smoke) exist, may
discolor walls.
Clearances
Adequate clearances must be provided for accessibility for
purposes of servicing and proper operation.
Floor Mounted With Optional Base
1.
Minimum clearance between the heater and adjacent
walls is 6".
2.
Minimum clearance between the heater and ceiling is
36".
Wall Mounted
8
1.
Minimum clearance to adjacent walls is 6".
2.
Minimum clearance to floor (top surface of carpeting, tile
or other combustible material) is 6".
3.
Minimum clearance between the heater and ceiling is
36".
Installing Your Heater
Installation and repair should be done by a qualified service
technician.
An inspection of the heater and attached systems should be
performed at least once each year by a qualified service
technician. More frequent inspections are advisable if the heater
is installed or operated in a manner that might cause the
accumulation of dust or dirt in the heater, or the failure of
component parts may occur more rapidly than would normally be
expected.
In Canada:
Floor Mounting
1.
The floor mounting stand is required if floor mounted.
WARNING: This installation is not complete until
floor mounting stand is installed.
2.
Refer to page 26 for further floor base instructions.
Models
0656541.9; 0656542.9; 1056511.9; 1056512.9
1056541.9; 1056542.9
Installation must conform with local codes or, in the absence of
local codes, with the current standard CAN/CGA - B 149.1 Natural
Gas Installation Code or CAN/CGA - B149.2 Propane Installation
Code.
If the unvented room heater is installed in a residential garage, the
following precautions must be taken.
•
The heater pilot and burner must be at least 24-inches
above the floor.
•
The heater must be located and protected, so as not to
be subjected to damage by a moving vehicle.
•
All flammable fuels must be removed.
Connect the unvented room heater to the gas supply line as
specified by the "Gas Supply and Piping Requirements" section
on page 10 of this manual.
Wall Mounting
1.
Install mounting brackets on wall. Use enclosed "paper
template" for proper location of holes. It may be necessary to
use plastic or lead anchors for plaster walls. These are
standard hardware items, available locally.
2.
After mounting brackets are installed, hang unvented room
heater on mounting brackets in holes provided at the rear of
the heater.
3.
The illustration above details the mounting bracket positions.
This assures proper clearances once the heater is mounted
on the wall. Use the paper template to locate the bracket
height. See minimum clearances on page 8.
9
Installing Your Heater
Gas Supply and Piping
If you are not sure what type gas is available in your locality,
obtain this information from your local gas supply company
prior to installing the heater.
The pilot and control system of this heater will automatically
stop the gas flow to the pilot burner and main burner if the pilot
flame is extinguished. This system also generates the
electricity required to operate the thermostat system. Since no
electrical power is required from any other source, this heater
will continue to operate during a power outage, with the
exception of the optional blower kit.
If installation is for L.P. Gas, have the L.P. installer use a twostage regulator and make all connections from storage tank to
heater.
Use two pipe wrenches when making the connection to the
valve to prevent turning or damage to gas valve.
Piping
Gas pipe must be installed by a qualified installer. The pipe
system must comply with local codes and ordinances or with
the latest edition of the American National Fuel Gas Code
Z223.1.
WARNING: All gas piping and connections must
be tested for leaks after installation or servicing all
leaks must be corrected immediately.
1.
5.
Use ground joint unions.
6.
Install a drip leg (sediment trap). The drip leg is required
to prevent condensate and scale particles from entering
the gas valve.
7.
Install a manual shut-off valve.
8.
Provide a 1/8 NPT test gauge connection immediately
before the gas supply connection to the heater.
9.
Do not locate pipe joints in a concealed location where
leak detection and repairs are difficult or impossible.
The gas supply line must be of an adequate size to handle
the Btu/hr requirements and length of the run for the unit
being installed. Determine the minimum pipe size from
below table basing the length of the run from the gas
meter or source to the unit.
LENGTH OF
PIPE-FEET
20
40
60
LENGTH OF
PIPE-FEET
20
40
60
NATURAL GAS
PIPE CAPACITY - Btu/hr
(INCLUDES FITTINGS)
PIPE SIZE
1/2
3/4
INCH
INCH
92,000
190,000
63,000
130,000
50,000
105,000
L. P. GAS
PIPE CAPACITY - Btu/hr
(INCLUDES FITTINGS)
PIPE SIZE
1/2
3/4
INCH
INCH
189,000
393,000
129,000
267,000
103,000
217,000
1 INCH
350,000
245,000
195,000
1 INCH
732,000
504,000
409,000
2.
Use new, properly reamed pipe free from chips such as
steel or black iron pipe and fittings or other approved by
local codes.
3.
Do not thread pipe too far. Valve distortion or malfunction
may result from excess pipe within the control.
4.
Use moderate amount of good quality compound to pipe
only, leaving 2 end threads bare. If L.P. gas installation,
use compound resistant to action of liquefied petroleum
gases.
IMPORTANT: Hold pressure regulator with wrench when
connecting it to gas piping and/or fittings.
1.
Make sure the control of the heater is in the "OFF"
position.
2.
Open the manual shut off valve. Test for leaks by applying
a liquid detergent to all joints. Bubbles forming indicate a
leak.
3.
Correct any leak at once.
CAUTION: Never use an open flame to check for
leaks.
10
Installing Your Heater
Gas Pressure Check
The heater regulator controls the gas pressure to the burner.
The gas pressure should be checked at the pressure test point.
Pressure should be checked with unit on high.
The pressure test point for these models is a 1/8" NPT plugged
tap located at the bottom of the regulator (see illustration
below). To gain access to the regulator, follow these steps:
WARNING: Danger of property damage, bodily
injury or death.
Make sure the heater is equipped to operate on
the type of gas available. Models designated as
natural gas are to be used with natural gas only.
Heaters designated for use with Liquefied
Petroleum (L. P.) gas have orifices sized for
commercially pure propane gas. They cannot be
used with butane or a mixture of butane and
propane.
The maximum inlet supply pressure for this heater must be 7.0
inches for natural gas and 13 inches for LP gas. The minimum
inlet supply pressure for the purpose of input adjustment must
be 5 inches for natural gas and 11 inches for LP gas. The
control on this heater is equipped with a regulator which
reduces the manifold pressure to 4 inches for natural gas and
10 inches for LP gas.
Pressure Testing Supply Line
1.
Lift screen straight up. Pull bottom of screen out. Pull
screen down and set aside.
2.
Remove two (2) screws on bottom front panel. Remove
bottom front panel and set aside.
3.
Pressure test is at the regulator.
system during pressure testing of that system at test pressures
in excess of 1/2 psig (3.5 kPa). The unvented room heater
must be isolated from the gas supply piping system by closing
its individual manual shutoff valve during any pressure testing
of the gas supply piping system at test pressures equal to or
less than 1/2 psig (3.5 kPa). Pressures in excess of 1/2 psig
(3.5 kPa) will cause damage to the control valve and may
cause damage to the shutoff valve.
WARNING: Danger of property damage, bodily
injury or death.
Never use a match or open flame to test for
leaks. Never exceed specified pressures for
testing. High pressures may damage the gas
valve and cause overfiring which may result in
improper combustion and possible production of
carbon monoxide. Liquid Petroleum (L. P.) is
heavier than air and it will settle in any low area,
including open depressions, and it will remain
there unless area is ventilated. Never attempt
startup of unit before thoroughly ventilating area.
CAUTION: The unvented room heater and its individual
shutoff valve must be disconnected from the gas supply piping
11
Installing Your Heater
WARNING: Carbon monoxide is a poisonous,
combustible gas formed by incomplete
combustion. It is colorless, odorless and
tasteless. Depending on the length of exposure
and the amount inhaled, carbon monoxide can
cause –
•
Dizziness
•
Headache
•
Nausea
•
Bodily injury (brain damage)
•
Death by asphyxiation
If you encounter or suspect that carbon
monoxide is present, get fresh air at once and
seek medical attention immediately.
WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause
injury or property damage. Refer to this manual.
For assistance or additional information, consult
a qualified installer, service agency or the gas
supplier.
Operating Your Heater
FOR YOUR SAFETY, READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property
damage, personal injury or loss of life.
LIGHTING THE PILOT
A.
This appliance is equipped with an ignition device which
manually lights the pilot.
B.
BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
C. WHAT TO DO IF YOU SMELL GAS
•
Do not try to light any appliance or strike a match.
•
Do not touch any electric switch; do not use any
phone in your building.
•
Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions
•
If you cannot reach your gas supplier, call the fire
department.
D. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don't try to repair it, call a qualified service
technician. Force or attempted repair may result in a fire
or explosion.
E.
Do not use this appliance if any part has been under
water. Immediately call a qualified service technician to
inspect the appliance and to replace any part of the
control system and any gas control which has been
underwater.
OPERATING INSTRUCTIONS
1.
2.
3.
STOP! Read the safety information above.
Check that gas supply to the heater is on.
Push in gas control knob slightly and turn clockwise
to "OFF".
Gas control knob
is shown in
"OFF" position
4.
5.
12
Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP!
Follow "C" in the safety information above on this label. If
you don't smell gas, go to the next step.
Push in gas control knob slightly and turn
counterclockwise to "PILOT/IGN" and depress for five (5)
seconds.
6.
7.
8.
Release control knob pressure and turn clockwise to
"OFF".
Depress control knob while OFF, then turn back to
PILOT/IGN. This should cause the spark from the piezo
igniter to light the pilot gas. Keep control knob depressed
for ten (10) seconds before releasing. If pilot does not
light, repeat steps 5 through 7.
Press the control knob down slightly and rotate
counterclockwise to "ON". Release the knob.
Operating Your Heater
TO TURN OFF GAS TO APPLIANCE
1.
Push the gas control knob in slightly and turn clockwise to
"OFF". DO NOT FORCE.
WARNING: The surface of the heater is hot
during operation. Keep children, clothing,
furniture and flammable material away from the
heater.
WARNING: Do not store or use gasoline or
other flammable liquids or vapors near the
heater.
CHECK BURNER PILOT FLAME
“Normal” illustrates a correct burner flame pattern.
WARNING: If you do not follow these
instructions exactly, a fire or explosion may result
causing property damage, personal injury or loss
of life.
A.
B.
This appliance is equipped with an ignition device which
manually lights the pilot.
BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
C.
WHAT TO DO IF YOU SMELL GAS
Normal
NOTE: Do not mistake orange flames with yellow tipping. Dirt
or other fine particles can enter the heater and burn, causing
brief patches of orange flame.
“Abnormal” illustrates an incorrect burner flame pattern. The
incorrect burner flame pattern shows yellow tipping of the
flame.
D.
Abnormal
WARNING: If yellow tipping occurs, your heater
could produce increased levels of carbon
Monoxide. If burner flame shows yellow tipping,
see "troubleshooting" section of this manual.
E.
•
Do not try to light any appliance or strike a match.
•
Do not touch any electric switch; do not use any
phone in your building.
•
Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions
•
If you cannot reach your gas supplier, call the fire
department.
Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don't try to repair it, call a qualified service
technician. Force or attempted repair may result in a fire
or explosion.
Do not use this appliance if any part has been
underwater. Immediately call a qualified service
technician to inspect the appliance and to replace any
part of the control system and any gas control which has
been under water.
WARNING: A visual check of the burner pilot flame should be made periodically.
13
Caring for Your Heater
WARNING: DANGER OF BODILY INJURY OR DEATH
If fan kit accessory is used, turn off electric power supply at disconnect switch, fuse box or service panel
before removing any doors or access/service panels from unit.
Annual Upkeep Needed
It is recommended that a qualified service technician inspect
the heater annually.
Cabinet
Clean cabinet with damp cloth. Never use abrasive cleaners.
Cabinets are finished in heat resistant baked enamel. DO NOT
refinish with wall paint.
ODS Pilot and Burner
Use a vacuum cleaner, pressurized air, or small, soft bristled
brush to clean the ODS pilot and burner. Never use a wire,
needle or similar object to clean ODS pilot. This could damage
the ODS pilot unit.
Service, repair or maintenance of the unvented heating system
should only be attempted by a qualified service technician.
The burner and control of the heater should be cleaned and
checked at least once each year by a qualified service
technician. If there is any indication that the heater is
operating improperly, turn it off and have it checked
immediately. Lint and dust may be vacuumed from the interior
of the heater, when it is cool. The control and main burner can
be blown free of dust and lint with a vacuum cleaner or
pressurized air.
Keep all combustible materials, gasoline and other flammable
liquids or vapors away from this heater. Be sure that
combustion and ventilation air openings supplying this heater
are kept clear at all times.
Continued safe and satisfactory performance of this heater
requires, but is not limited to, periodic examination of the pilot
flame, combustion chamber, liners and gas supply lines, and
periodic cleaning of the burner air intake, pilot and control
areas.
Inspecting Pilot
“Normal” illustrates a correct pilot flame pattern.
Abnormal illustrates an incorrect pilot flame pattern. The
incorrect pilot flame is not touching the thermocouple. This
causes the thermocouple to cool and the heater to shutdown.
If the pilot flame pattern is incorrect, turn the heater off (see
"Turn Off Gas to Appliance" on page 13) and refer to
"Troubleshooting" on pages 15-16.
Normal
Abnormal
14
Troubleshooting Your Heater
SYMPTOM
1.
No spark at ODS pilot when
igniter button is pressed.
POSSIBLE CAUSE
A.
B.
Igniter electrode positioned wrong.
Igniter electrode broken.
C.
Igniter electrode not connected to
igniter cable.
D. Igniter cable pinched or wet.
E. Piezo igniter is loose.
3.
Pilot is lit but burner does not
ignite.
4.
Delayed ignition of burner.
5.
ODS pilot lights but does not
remain lighted when control
knob is released.
D.
E.
ODS pilot is clogged.
F.
A.
B.
A.
Gas regulator setting not correct.
Burner orifice is clogged.
Inlet gas pressure is too low.
Manifold pressure is too low.
B.
A.
B.
F.
G.
H.
I.
A.
B.
Burner orifice is clogged.
Control knob not fully pressed in.
Control knob not pressed in long
enough.
Safety interlock system has been
triggered.
Manual shutoff valve not fully open.
Thermocouple connection loose at
control valve.
Low gas pressure.
Dirty or clogged pilot.
Thermocouple damaged.
Control valve damaged.
Burner orifice is clogged or damaged.
Burner damaged.
C.
A.
B.
Gas regulator defective.
Not enough air.
Gas regulator defective.
Replace.
Check burner for dirt. Clean.
Replace gas regulator.
A.
Residues from manufacturing
processes.
Metal expanding while heating or
contracting while cooling.
Problem will stop after a few hours of
operation.
This is common in most heaters. If noise is
excessive, contact qualified service
technician.
Ventilate room. Stop using odor causing
products while heater is on.
Locate and correct all leaks.
A.
B.
C.
C.
D.
E.
6.
7.
Burner backfiring during
combustion.
Yellow flame during burner
combustion. Do not operate in
this condition. See Carbon
Monoxide warning on page 12.
8.
Slight smoke or odor during
initial operation.
9.
Heater produces a
clicking/ticking noise just after
burner is lit or shut off.
10. Heater produces unwanted
odors.
Reconnect igniter cable.
Gas supply turned off or manual
shutoff valve closed.
Control knob not in PILOT position.
Control knob not pressed in while in
PILOT position.
Air in gas lines when installed.
Broken igniter cable.
G. Bad Piezo igniter.
Spark at ODS pilot but no
ignition when igniter button is
pressed.
Replace ODS pilot assembly.
Replace ODS pilot assembly.
Free igniter cable if pinched. Keep dry.
Press piezo igniter to valve located inside
heater cabinet top.
Thermostat models – Replace igniter cable.
Manual models - Replace valve.
Thermostat models - Replace piezo igniter.
Manual models - Replace valve
Turn on gas supply or open manual shutoff
valve.
Turn control knob to PILOT position.
Press in control knob while in PILOT
position.
Hold down control knob. Repeat igniting
operation until air is removed.
Clean ODS pilot or replace ODS pilot
assembly.
Replace gas regulator.
Clean burner or replace burner orifice.
Contact local gas company.
Contact local gas company. Replace
regulator.
Clean burner.
Press control knob in fully.
After pilot lights, keep control knob pressed
in 30 seconds.
Wait one (1) minute for safety interlock
system to reset. Repeat ignition operation.
Open valve.
Hand tighten until snug, then tighten 1/4
turn more.
Contact local gas company.
Clean pilot or replace pilot assembly.
Replace ODS pilot assembly.
Replace.
Clean burner or replace burner orifice.
Replace.
F.
2.
CORRECTIVE ACTION
A.
A.
B.
Heater burning vapors from paint, hair
spray, glue, etc.
Gas leak.
15
Troubleshooting Your Heater
11. Gas odor even when control
knob is in “OFF” position.
12. Excessive moisture on
windows and other surfaces.
13. Heater shuts off while in use,
but operates.
14. When burner is lit, heater
makes a whistling noise.
A.
B.
A.
B.
Gas leak.
Control valve defective.
Heater is oversized for the area in
which it is installed.
Not enough fresh air available.
Not enough fresh air available.
Low line pressure.
Pilot is partially clogged.
Turning control knob to “HI” position
when burner is cold.
Air in gas line.
C.
D.
Air passageways on heater blocked.
Dirty or clogged burner orifice.
B.
A.
B.
C.
A.
Order Replacement Parts
Replacement parts for models
0656542.9; 0656541.9; 1056512.9; 1056511.9; 1056542.9; 1056541.9;
2056512.9; 2056511.9; 3056512.9; 3056511.9
Use Only Manufacturer's Replacement Parts.
16
Locate and correct all leaks.
Replace.
Add more combustion air to the room.
Add more combustion air to the room.
Open windows and/or doors for ventilation.
Contact local gas company.
Clean pilot.
Turn control knob to “LO” position and let
burner warm up.
Operate burner until air is removed from
line. Have gas line checked by local gas
company.
Check minimum installation clearances.
Clean burner.
Order Replacement Parts List
REF.
NO.
PART NO.
DESCRIPTION
1
1
1
1
2
2
3
3
3
4
26B155
26D005-1
26D003-1
26D004-1
26D002-2
26D001-2
26C001
26C002
26C003
26B027
Top Panel Assembly, Small
Top Panel
Top Panel
Top Panel
Right Side Panel
Right Side Panel
Back Panel
Back Panel
Back Panel
Bottom Glass Support
4
4
5
5
5
6
6
6
7
7
7
8
26B025-1
26B025-2
26B005
26B006
26B007
P322744
P322746
P322748
P322902
P322901
P322900
26B098
Bottom Glass Support
Bottom Glass Support
Bottom Front Panel
Bottom Front Panel
Bottom Front Panel
Front Screen
Front Screen
Front Screen
Glass
Glass
Glass
Hearth Assembly
8
8
9
9
9
10
10
10
11
11
11
12
26B099
26B100
26B026-1
26B026-2
26B026-3
26A001
26A002
26A003
26B002
26B003
26B004
26D002-1
Hearth Assembly
Hearth Assembly
Top Glass Support
Top Glass Support
Top Glass Support
Deflector
Deflector
Deflector
Top Front Panel
Top Front Panel
Top Front Panel
Left Side Panel
12
26D001-1
Left Side Panel
0656541.9;
0656542.9
1056541.9;
1056542.9
X
X
1056511.9;
1056512.9
2056512.9;
2056511.9
3056512.9;
3056511.9
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
17
Replacement Parts List
Control Assembly - 0656541.9; 0656542.9; 1056541.9; 1056542.9.
Use Only Manufacturer's Replacement Parts.
18
Service and Orders – 19
Order Replacement Parts
REF.
NO.
PART NO.
DESCRIPTION
1
2
3
4
P322658
26B032
26B033
P322916
Knob
Regulator Tube Assembly
Burner Tube Assembly
Orifice
4
4
4
5
6
6
7
8
9
9
10
10
P322915
P322914
P322913
P322918
P322899
P322898
P322903
P323018
P322893
P322892
26B112-1
26B112-2
Orifice
Orifice
Orifice
3/8" Fitting
Regulator
Regulator
Street Elbow
Regulator Plug
ODS Pilot
ODS Pilot
Burner Assembly
Burner Assembly
10
10
11
12
26B113-1
26B113-2
P322740
26B034
Burner Assembly
Burner Assembly
Valve
Pilot Tube Assembly
0656541.9
X
X
X
X
0656542.9
X
X
X
1056541.9
1056542.9
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
19
Replacement Parts List
Control Assembly - 1056511.9; 1056512.9.
Use Only Manufacturer's Replacement Parts.
20
Service and Orders – 21
Order Replacement Parts
Control Assembly - 2056511.9; 2056512.9.
Use Only Manufacturer's Replacement Parts.
21
Order Replacement Parts
Control Assembly - 3056511.9; 3056512.9.
Use Only Manufacturer's Replacement Parts.
22
Service and Orders – 23
Replacement Parts
REF.
NO.
PART NO.
DESCRIPTION
1056511.9
1
26C007-1
Valve Assembly
1
1
1
1
1
2
26C007-2
26C007-3
26C007-4
26C007-5
26C007-6
P322903
3
26B032
3
26B028
4
4
26B033
26B029
Valve Assembly
Valve Assembly
Valve Assembly
Valve Assembly
Valve Assembly
Street Elbow
Regulator Tube
Assembly
Regulator Tube
Assembly
Burner Tube Assembly
Burner Tube Assembly
5
5
5
5
5
5
6
7
7
8
9
9
P322914
P322913
P322912
P322911
P322910
P322909
P322919
P322898
P322899
P323018
P322893
P322892
Orifice
Orifice
Orifice
Orifice
Orifice
Orifice
3/8" Fitting
Regulator
Regulator
P323018 Regulator Plug
ODS Pilot
ODS Pilot
X
10
10
10
10
10
10
26B113-1
26B113-2
26B114-1
26B114-2
26B115-1
26B115-2
BURNER ASSEMBLY
BURNER ASSEMBLY
BURNER ASSEMBLY
BURNER ASSEMBLY
BURNER ASSEMBLY
BURNER ASSEMBLY
X
1056512.9
2056511.9
2056512.9
3056511.9
3056512.9
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
23
Installing and Operating Your Blower Accessory
Blower Accessory 2205 and 2206
1.
2.
Disconnect unit from gas supply and wall before installing
blower.
Remove back plate from unit by unscrewing four (4)
screws. Retain four (4) screws back plate for installation
of blower. Discard back plate.
3.
Install blower as shown in the illustration. Use the four (4)
screws retained to mount blower to the back panel.
4.
The blower assembly is equipped with a three-prong, 7-foot power cord. Use a standard three-hole, grounded outlet. If an
extension cord is needed, use a standard three- prong grounded cord with a three-hole receptacle.
Blower Operation for model 2205, - turn thermostat switch to "ON" position. Turn heater on. Blower will cycle "ON" or "OFF" as
the thermostat heats and cools to desired temperature. Turn the heater “OFF” and the blower will automatically turn off, or switch
the blower ON/OFF switch to the "OFF" position.
To operate model 2206, turn switch to "ON" or "OFF" position as desired.
5.
This unit must be grounded for your protection against electrical shock.
24
Service and Orders – 25
Installing and Operating Your Blower Accessory
Floor Base 4287 and 4288
1.
Lay heater on its back. Loosen two (2) screws, located on bottom of heater - Do Not Remove Screws.
2.
Attach floor base to heater with two (2) keyholes located on top of the floor base. Tighten screws. Use two (2) screws, included
with kit, to attach back of floor base to the bottom back of the heater.
3.
Stand the heater upright. Select the location of heater.
Refer to page 8 for minimum clearances.
4.
Connect gas piping. See page 10 for gas supply and
piping instruction.
5.
Use two (2) floor mounting screws, depending on your
floor construction, to mount the bottom back of the floor
base to the floor.
25
In addition to the Installation and Operating Instruction Manual packaged with this unvented heater, all installations in the State of
Massachusetts must use the following requirements when installing, maintaining or operating unvented propane or natural gas-fired
space heaters.
527 CMR 30.00 UNVENTED PROPANE OR NATURAL GAS-FIRED SPACE HEATERS
Section
30.01:
30.02:
30.03:
30.04:
30.04:
Purpose
Scope
Definitions
Installation
Maintenance and Operation
30.01: Purpose
The purpose of 527 CMR 30.00 is to provide requirements for the installation, maintenance, and operation of unvented propane
or natural gas fired space heaters.
30.02: Scope
527 CMR 30.00 shall apply to unvented propane natural gas-fired space heaters installed in occupancies used in whole or in part
for habitation on or after April 1, 2004. 527 CMR 30.00 shall not apply to unvented propane or natural gas-fired space heaters
used in habituated spaces or those installed in accordance with 527 CMR 20.
30.03: Definition
Malfunction, shall mean condition where a space heater fails to operate properly as provided in the manufacturer's instructions.
Oxygen Depletion Safety Shutoff System (ODS): A device utilized to shut off the gas supply to the pilot or main burner when the
oxygen in the surrounding atmosphere is depleted to the percent concentration developed by the manufacturer, but under no
circumstances shall the concentration be less than 18 percent oxygen concentration.
Primary Heat: A heat source that is permanently installed and used exclusively to provide heat to the entire structure (e.g. forced
hot water, forced hot air) by means of a central heater or boiler which has a permanent fuel source (e.g. oil, natural gas or LPG)
or electric heat. 527 CMR 30.03. Primary Heat shall not include fireplaces or wood stoves.
Unvented Natural or Propane Gas-Fired Space Heater: A permanently installed stand alone gas-fired unvented room heater or
gas-fired unvented decorative room heater for connection to the house fuel supply system which utilizes natural gas or propane.
Unvented gas-fired space heaters may be used only for supplemental heat and/or decorative purposes and under no
circumstances shall they provide a primary heat source. Unvented gas-fired space heaters shall comply with ANSI Standard
Z21.11.2 - 2000 edition, Volume II.
30.04: Installation
26
1.
A permit shall be obtained from the head of the fire department and the local or state gas inspector having jurisdiction for
the installation of all unvented propane or natural gas-fired space heaters. Said permits shall be conditioned upon final
inspection and approval of installation by the head of the fire department and the local or state gas inspector having
jurisdiction. A copy of the manufacturer’s installation/operating literature shall be submitted with each permit application.
Before operation, the Head of the Fire Department and the local or state gas inspector shall inspect the installation for
compliance with 527 CMR and 248 CMR (Board of State Examiners of Plumbers and Gas Fitters).
2.
Unvented propane or natural gas-fired space heaters shall conform to ANSI Z21.11.2, be equipped with an oxygen
depletion safety (ODS) shutoff system and be listed and approved in accordance with 248 CMR.
3.
Unvented propane or natural gas-fired space heaters shall be installed in accordance with their listings and the
manufacturer's instructions. Proper clearances to combustibles shall be maintained. In no case shall the clearances be
such as to interfere with combustion air and accessibility.
4.
Installations shall be of a permanent type, with a permanently piped fuel supply in accordance with 248 CMR. LPG
appliances shall be subject the storage requirements in accordance with 527 CMR 6.00. Portable unvented propane or
natural gas-fired space heaters shall be prohibited.
5.
Unvented propane or natural gas-fired space heaters shall be prohibited in bedrooms and bathrooms.
6.
Space heaters shall be properly sized for the room or space of installation, but shall not exceed a maximum of 40,000
Btu/hr input per room or space.
7.
In occupancies with an unvented propane or natural gas-fired space heater; at least one listed carbon monoxide
detector shall be installed and maintained in any room or space where said heater has been installed in accordance with
the manufacturer’s instructions. Any building wherein said heater is to be installed shall, as a precondition to such
installation, have working smoke detectors installed and maintained in accordance with the requirements of 780 CMR
Service and Orders – 27
(State Board of Building Regulations and Standards) in effect at the time of construction or if no said requirement was in
effect at the time of construction, installed as provided for in M.G.L.c 148, §26E.
8.
In rooms and buildings served by an unvented propane or natural gas-fired space heater, a primary source of heat which
is operable, shall be permanently installed and maintained in said building in accordance with 105 CMR (Department of
Public Health).
9.
Seller of unvented propane or natural gas-fired space heaters shall provide to each purchaser a copy of 527 CMR 30.00
upon sale of the unit.
30.05: Maintenance and Operation
1.
The maintenance and operation of unvented propane or natural gas-fired space heaters shall be in accordance with the
manufacturer’s instructions. The manufacturer’s instructions shall be left with the appliance and made available for any
public official.
2.
Any malfunction of an unvented space heater shall forthwith be reported by the owner to the-head of the local fire
department.
REGULATORY AUTHORITY
527 CMR 30.00 M.G.L.c. 148, §25E
27
Hints and Information
Service Hints
If your unvented heater fails to work correctly, you may avoid inconvenience and the cost of a service call by checking the
troubleshooting section on pages 15 and 16 before you call for service.
WARNING: If the information in this manual is
not followed exactly, a fire or explosion may
result causing property damage, personal
injury or loss of life.
– Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
– This appliance should be inspected before use
and at least once a year by a qualified service
person. Installation and repairs must be done
by a qualified service person.
– What to do if you smell gas
• Open all windows
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Extinguish any open flame.
• Immediately call your gas supplier, call the
fire department.
• Installation and service must be performed by
a qualified installer, service agency or the
gas supplier.
How to Order Repair Parts
When ordering repair parts, always give the following Information:
1.
Model number
2.
Serial number
3.
Part number
4.
Part description
All parts listed herein may be ordered from your equipment supplier. The model number of your Williams unvented gas heater will be
found on the nameplate near gas valve, inside control compartment.
Williams Furnace Company • 250 West Laurel Street, Colton, CA 92324
(909) 825-0993 • FAX: (909) 824-8009
Manufactured in the U.S.A. • Established 1916
28
P923665 October 2014
ALL RIGHTS RESERVED
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement