VocoPro UHF-8900 Operating instructions

Add to my manuals
24 Pages

advertisement

VocoPro UHF-8900 Operating instructions | Manualzz

UHF-8900

UHF PLL WIRELESS MIC SYSTEM WITH FREQUENCY SCAN

o w n e r ' s m a n u a l

Table of Contents

Safety Instructions . . . . . . . . . . . . . . 3

FCC Information . . . . . . . . . . . . . . . . 4

Welcome . . . . . . . . . . . . . . . . . . . . . 5

Listening for a Lifetime . . . . . . . . . . . 6

Features . . . . . . . . . . . . . . . . . . . . . 7

Getting Connected . . . . . . . . . . . . . . 8

Descriptions and Functions . . . . . . . 10

Setting up the Microphones . . . . . . . 13

Re-syncing the Microphones . . . . . . . 16

Using the Wireless Mics . . . . . . . . . 17

Basic Operations . . . . . . . . . . . . . . 18

Advanced Operations . . . . . . . . . . . . 19

Frequency Reference . . . . . . . . . . . . 20

Troubleshooting . . . . . . . . . . . . . . . 23

Safety Instructions

CAUTION

RISK OF SHOCK

CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Only refer servicing to qualified service personnel.

Explanation of Graphical Symbols symbol, within an equilateral triangle, presence of danger.

The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and servicing instructions.

WARNING

To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture.

location does not interfere with its proper ventilation.

For example, the appliance should not be situated on a

bed, sofa, rug, or similar surface that may block the

ventilation slots.

heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers)

that produce heat.

connected to a power supply only of the type

described in the operating instructions or as marked

on the appliance.

taken so that the grounding or polarization means of

an appliance is not defeated.

should be routed so that they are not likely to be

walked on or pinched by items placed upon or

against them, paying particular attention to cords at

plugs, convenience receptacles, and the point where

they exit from the appliance.

before cleaning. Do not use liquid cleaners or

aerosol cleaners. Use a damp cloth for cleaning.

1. Read Instructions - All the safety and operating

instructions should be read before the appliance is

operated.

2. Retain Instructions - The safety and operating

instructions should be retained for future reference.

3. Heed Warnings - All warnings on the appliance and in

the operating instructions should be adhered to.

4. Follow Instructions - All operating and use

instructions should be followed.

5. Attachments - Do not use attachments not

recommended by the product manufacturer as they

may cause hazards.

6. Water and Moisture - Do not use this unit near water.

For example, near a bathtub or in a wet basement and

the like.

7. Carts and Stands - The appliance should be used

only with a cart or stand that is recommended by the

manufacturer.

7 A. An appliance and cart combination

should be moved with care. Quick stops,

excessive force, and uneven surfaces may

cause an overturn.

should be unplugged from the outlet when left unused

for a long period of time.

that objects do not fall and liquids are not spilled into

the enclosure through openings.

A. The power supply cord or plug has been damaged; or

B. Objects have fallen into the appliance; or

C. The appliance has been exposed to rain; or

D. The appliance does not appear to operate normally

or exhibits a marked change in performance; or

E. The appliance has been dropped, or the enclosure

damaged.

the appliance beyond that described in the operating

instructions. All other servicing should be referred to

qualified service personnel.

To CATV system installer's (U.S.A.): This reminder is provided to call the CATV system installer's attention to

Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected as close to the point of cable entry as practical.

3

FCC Information

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!: This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by

Vocopro may void your authority, granted by the FCC, to use this product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable(s) supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your

FCC authorization to use this product in the U.S.A.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations,

Part 15 for Class "B" digital devices. Compliance with these requirements provides a reasonable level of assurances that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the owner's manual, may cause interference harmful to the operation of other electronic devices. Compliance with

FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit "Off" and "On", please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Use power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter(s).

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300-ohm ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact your local retailer authorized to distribute Vocopro products. If you can not locate the appropriate retailer, please contact Vocopro, 1728

Curtiss Court, La Verne, CA 91750.

CAUTION

The apparatus is not disconnected from the AC power source so long as it is connected to the wall outlet, even if the apparatus itself is turned off. To fully ensure that the apparatus is indeed fully void of residual power, leave unit disconnected from the AC outlet for at least fifteen seconds.

CAUTION:

READ THIS BEFORE OPERATING YOUR UNIT

1. To ensure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2. Install your unit in a cool, dry, clean place - away from

windows, heat sources, and too much vibration, dust,

moisture or cold. Avoid sources of hum (transformers,

motors). To prevent fire or electrical shock, do not

expose to rain and water.

3. Do not operate the unit upside-down.

4. Never open the cabinet. If a foreign object drops into

the set, contact your dealer.

5. Place the unit in a location with adequate air

circulation. Do not interfere with its proper ventilation;

this will cause the internal temperature to rise and may

result in a failure.

6. Do not use force on switches, knobs or cords. When

moving the unit, first turn the unit off. Then gently

disconnect the power plug and the cords connecting to

other equipment. Never pull the cord itself.

7. Do not attempt to clean the unit with chemical solvents:

this might damage the finish. Use a clean, dry cloth.

8. Be sure to read the "Troubleshooting" section on

common operating errors before concluding that your

unit is faulty.

9. This unit consumes a fair amount of power even when

the power switch is turned off. We recommend that you

unplug the power cord from the wall outlet if the unit is

not going to be used for a long time. This will save

electricity and help prevent fire hazards. To disconnect

the cord, pull it out by grasping the plug. Never pull the

cord itself.

10. To prevent lightning damage, pull out the power cord

and remove the antenna cable during an electrical

storm.

11. The general digital signals may interfere with other

equipment such as tuners or receivers. Move the

system farther away from such equipment if

interference is observed.

NOTE:

Please check the copyright laws in your country before recording from records, compact discs, radio, etc. Recording of copyrighted material may infringe copyright laws.

Voltage Selector (General Model Only)

Be sure to position the voltage selector to match the voltage of your local power lines before installing the unit.

110V

4

Welcome

And thank you for purchasing the UHF-8900 from VocoPro, your ultimate choice in vocal entertainment! With years of experience in the music entertainment business,

VocoPro is a leading manufacturer of vocal equipment, and has been providing patrons of bars, churches, schools, clubs and individual consumers the opportunity to sound like a star with full-scale club models, in-home systems and mobile units. All our products offer solid performance and sound reliability, and to reinforce our commitment to customer satisfaction, we have customer service and technical support professionals ready to assist you with your needs. We have provided some contact information for you below.

VocoPro

1728 Curtiss Court

La Verne, CA 91750

Toll Free: 800-678-5348

TEL: 909-593-8893

FAX: 909-593-8890

VocoPro Company Email Directory

Customer Service & General Information [email protected]

Tech Support [email protected]

Remember Our Website

Be sure to visit the VocoPro website www.vocopro.com for the latest information on new products, packages and promos. And while you're there don't forget to check out our Club VocoPro for Karaoke news and events, chat rooms, club directories and even a KJ Service directory!

We look forward to hearing you sound like a PRO, with VocoPro, the singer’s ultimate choice.

FOR YOUR RECORDS

Model Number

Serial Number

Date of Purchase

Place of Purchase

5

Listening for a Lifetime

Some common decibel ranges:

Level Example

The following noises can be dangerous under constant exposure:

Level Example

-Information courtesy of the Deafness Research Foundation

6

Features

Features

• 8 UHF PLL wireless microphones

• Frequency scan feature finds interference-free channels

• More than 150 wireless frequencies available

• LCD display shows frequency and other info

• 19” rack mountable chassis, uses just 2 rack spaces

• Independent power knob and volume control per channel

• 8 balanced XLR outputs

• (2) ¼” unblanced mixed outputs

• Includes (2) ¼” unbalanced microphone cables and metal carrying case

(2)

7

Getting Connected

Connecting Power

1. Ensure the main power switch on the rear panel is set to OFF.

2. Connect the power adapter to the power input on the rear panel.

3. Plug the power adapter into a power outlet, or a surge protector.

Note: A surge protector is recommended to protect your equipment from power surges.

Connecting Audio

Using the XLR outputs

The XLR outputs allow you to connect each channel to the mixer independently. This gives you more control over the individual microphone channels when connected to a mixer.

You will need:

• UHF-8900

• 8 XLR patch cables (not included)

• An input device, such as a mixer or amplifier (not included)

To Connect the XLR outputs:

1 . Ensure the main power switch on the rear panel is turned off .

2 . Connect one end of an XLR cable to the

CH.1 output of the UHF-8900.

3 . Connect the other end of the XLR cable to the desired input on your mixer.

4 3 2

Note: To avoid confusion, it’s recommended that the XLR jacks are attached correspondingly (e.g. CH.1 to CH. 1,

CH. 2 to CH. 2, etc. The illustrated setup is for clarity only.)

4. Repeat steps 2 and 3 until all the XLR outputs are connected.

1

4 3 2

Mixer

1

UHF-8900 rear panel

Using the ¼” mixed output

The ¼” mixed output is useful if you do not have a mixer or if you have limited inputs available on your mixer. All 4 microphone signals are mixed together in this output .

You will need:

• UHF-8900

• (2) ¼” patch cables (included)

• An input device, such as a mixer or amplifier (not included)

UHF-8900 rear panel

Mixer

To Connect the ¼” output:

1. Ensure the main power switch on the rear panel is turned off .

2. Connect one end of a ¼” cable to one of the ¼” mixed output on the rear panel of the UHF-8900.

3. Connect the other end of the ¼” cable to the desired input on your mixer or amplifier.

4. Repeat steps 2 and 3 for the second ¼” mixed output jack.

8

Getting Connected

Connecting Antennas

The Antennas receive the UHF wireless signals from the microphones.

1. Attach the antennas to the connectors on the front panel by twisting them clockwise until firmly attached.

2. To disconnect the antennas, twist counter-clockwise.

Note: Please be sure to attach the 900MHz antennas to the top 2 antenna posts and attach the 600MHz antennas to the bottom 2 posts.

Attaching the Rack Brackets

The UHF-8900 comes with detachable rack brackets which allows the unit to be installed in a standard 19 inch rack.

1. Use the included screws to fasten the rack brackets to the sides of the UHF-8900 as shown in the illustration below.

Mounting the UHF-8900 in a Rack

The UHF-8900 will fit in a standard 19” rack (not included).

1. Align the UHF-8900 with the desired space in rack and slowly slide in, rear panel first.

Note: Depending on your rack case design, it may be necessary to allow for sufficient space for the antennas.

2. While aligned, use rack case screws (not included) in the order shown below to stabilize the UHF-8900 in its space, using the “X” rotation (numbered below) will ensure even tension and flush alignment.

Note: Do not tighten screws firmly until all screws are in place.

1

2

3

4

9

Descriptions and Functions

1

3 4

5

2 8 7 6

Front Panel

1. Antenna Connector - Connect the antennas to these connectors to receive the wireless signals from the microphones.

2. Main Power Switch - This switch turns the power on and off for the whole unit.

3. Power/Volume Knob - Turn clockwise, until it clicks, to toggle OFF/ON.

- Turn clockwise past the click, to turn up the microphone volume for that channel..

4. Module Display Window - This LCD screen displays information about this module. See the Module Display Window descriptions and functions for more details .

5. Up/Set Button - Used to scroll up menu selections. When in IR Mode, it is used to confirm the desired frequency when choosing manually .

6. Menu Button - Used to cycle through menu screens .

Press once (1x) to toggle into the Group (GR) Selection menu.

Press twice (2x) to toggle into the Automatic Scan.

Press three times (3x) to toggle into the Channel (CH) Selection menu.

Press four times (4x) to toggle into IR Mode.

Note: Module menus have a 4 second timeout period. If the menu button wasn’t pressed within that time, the display will revert to the frequency information screen.

7. Down Button - Used to scroll down menu selections.

8. IR Sensor - Used to sync the desired microphone to the desired module .

Note: IR communication range is approximately 7 inches.

10

Descriptions and Functions

1 2 3 4

5

6 7

Module Display Window

1. MUTE Indicator - Displays when corresponding mic is off or disconnected. The Mute Mode is an automatic function.

2. Group and Channel - Displays the group and channel that the module is set to . *See Displaying the Group & Frequency page for details .

3. IR (infrared) Mode Indicator - Indicates when the module is in IR Mode, which is used to assign a microphone to a module.

4. Squelch* - Displays the current Squelch level for this module .

5. SCAN Mode Indicator - Shows when this module is in SCAN mode, which is used to search for an interference free frequency .

6. Lock - Setting alterations are disabled for that module when displayed.

Note: Press Menu+Set buttons simultaneously to toggle the Lock

6. AF/RF Level Bars - The RF bar displays signal strength of the synced microphone . The AF bar displays the strength of the audio signal being received from the microphone .

7. Channel Frequency - Displays what frequency this module is currently set to.

1

Rear Panel 1 2 3

1. Independent XLR Channel Outputs - These 8 balanced jacks output audio from each module independently.

2. Mixed Audio Output - These unbalanced jacks output the audio of all the modules in their respective rows.

3. Power Adapter Plug* - Attach the power adapter here to provide power to the receiver.

* See commonly asked questions for definition

11

Descriptions and Functions

Microphones

1. IR (infrared) Sensor - This sensor receives the infrared signal that is used to set the frequency that the wireless mic will use. This sensor is only used to set the microphone frequency, it does not send or receive audio signal .

2. Power LED - This LED indicator will turn green when the microphone is turned on. It will turn red when the batteries need to be replaced.

3. ON/OFF Switch - This switch turns the microphone on or off.

Installing the Batteries

To install the wireless mic batteries:

1 . Remove the battery cover .

2. Insert two fresh AA batteries. Make sure they are facing the correct direction.

3 . Replace the battery cover .

12

Setting up the Microphones

Overview

The goal is for each of the UHF-8900’s wireless channels to be operating on a frequency free of interference. This can be accomplished two ways 1) automatic frequency selection, and 2) manual frequency selection. We recommend using the automatic method first, as this method will work well for most areas. However, if you live in a metropolitan area where RF activity is dense, manual frequency selection may work better for you. If you choose the manual method, we recommend first obtaining information on your proximity to TV towers.

Frequencies and Groups

The UHF-8900 has a total of 177 available frequencies. These frequencies are broken down into groups. The two channels on the left are assigned GROUPS GR1-1 through GR1-C, while the two channels on the right are assigned GROUPS GR2-1 through GR2-C .

The top Module row - The groups are listed sequentially starting from GR 01 through GR 05.

The bottom Module row (Left 2 Modules) - The Groups are listed as GR 1-1 through G 1-A.

The bottom Module row (Right 2 Modules) - The Groups are listed as GR 2-1 through GR 2-A.

Pressing Buttons: 4 Second Default

When cycling through the selection modes and parameters using the MENU, UP, & DOWN buttons, if a selection is not made within 4 seconds, the system will automatically revert to the Frequency Information Screen. So, let’s say you are trying to change to a channel in a different group. After pressing MENU, you have only 5 seconds to press the UP/DOWN arrows to browse through the available groups. This applies to every step of the frequency setup procedure, so keep this in mind. If this happens, simply wait for it to finish and resume where you left off.

Other Devices

90°

Be sure to power on any other devices that may potentially interfere with the UHF-8900 (other wireless systems) BEFORE you begin the frequency selection process. This way, you will not have any surprises when they are powered on.

Antenna Positioning

For the best reception, position the receiver antennas at 90 degrees from each other. (see illustration).

WARNING: Please be sure to attach the 900MHz antennas to the top 2 antenna posts and attach the 600MHz antennas to the bottom 2 posts.

13

Setting up the Microphones

Setting the Frequencies Automatically

The microphones will be ready to use right out of the box. The below instructions are intended if interference is experienced at the venue being performed at. The Automatic instructions should be tried first and if problems persist, try the Manual settings .

Note: Please read through the steps before attempting to sync the microphones. The module menus have a 4 second timeout period where if a button is not pressed within that time the module will revert back to the frequency information screen.

AUTOMATIC SETUP

wireless microphone

Setting up the microphones using the frequency scan function.

1. Prepare the System: Ensure the receiver base, the desired module to be paired, and the desired microphone to be paired, are all powered on.

3

2. Identify the IR Sensors: Locate the IR Sensor on both microphone and module .

A.) Microphone - The IR Sensor is located just above the

ON/OFF switch.

B.) Module - The IR Sensor is located directly below the module volume knob.

VOL

SCAN

UP

DOWN

SET

MENU

3. Align the IR Sensors: Position the microphone so that the 2

IR sensors are level and within 3-5 inches of one another.

4. Select Scan: Press the MENU button on the desired module twice (2x). This will display the symbol “Scan” on the LCD. The

Scan Mode will last approximately 4 seconds.

5. Sync the Mic: The “Scan” symbol will be replaced with the “IR” symbol. With the IR symbol displayed, press the SET button to communicate the desired frequency to the microphone . This will display waves emanating from the “IR” symbol, when the waves disappear the screen will display the chosen frequency, as well as the AF and RF reception bars for that channel.

IR

SCAN

UHF-8900

VOL

IR PROGRAM MODE

IR

UHF-8900

5

SET

MENU

UHF PLL WIRELESS SYSTEM

WITH FREQUENCY SCAN

6. Test the Mic: Speak into the microphone to ensure sound in being produced and transmitted . The AF bars on the LCD should register as the microphone is spoken into.

VOL

SET

MENU Note: Once the microphone and module are synced, there will be a 5 second delay in audio each time the microphone is powered on. This is normal.

6

IR 7. Repeat the Process: Repeat steps 3-6 for each of the remaining microphones and modules .

UHF-8900 UHF PLL WIRELESS SYSTEM

WITH FREQUENCY SCAN

4

14

Setting up the Microphones

Setting the Frequencies Manually

If the UHF-8900 is used in an area with heavy RF interference, it may be beneficial to set the frequencies manually.

Please refer to the Advance Operation page to determine which frequencies to use for that area.

Note: Please read through the steps before attempting to sync the microphones. The module menus have a 4 second timeout period where if a button is not pressed within that time the module will revert back to the frequency information page.

MANUAL SETUP

wireless microphone

Setting up the frequencies manually

1 . Prepare the System: Ensure the receiver base, the desired module to be paired, and the desired microphone to be paired, are all powered on.

2 . Identify the IR Sensors: Locate the IR sensor on both the microphone and module .

A.) Microphone - The IR sensor is located just above the

ON/OFF switch.

B.) Module - The IR sensor is located directly below the module volume knob.

3 . Align the IR Sensors: Position the microphone so that the 2 IR sensors are level and within 3-5 inches of one another.

4 . Select a Group (GR): Press the Menu button on the desired module once (1x). This will display the symbol “GR” on the

LCD. With the “GR” symbol displayed, use the UP/DOWN buttons to select the desired group .

5 . Select a Channel (CH): Press the MENU button on the desired module twice (2x). This will cycle the menu past the “SCAN” screen and enter the Channel (CH) selection screen; this will display the symbol “CH” on the LCD. With the CH symbol displayed, use the UP/DOWN buttons to select the desired channel .

IR

IR

3

UHF-8900

VOL

CHANNEL SYMBOL

UHF-8900

UP

DOWN

UHF PLL WIRELESS SYSTEM

WITH FREQUENCY SCAN

UP

DOWN

SET

MENU

SET

MENU

6 . Sync Microphone: Press the MENU button once (1x) to enter

IR mode; this will display the symbol “IR” on the LCD. With the

IR symbol displayed, press the SET button to communicate the desired frequency to the microphone. This will display waves emanating from the “IR” symbol, when the waves disappear the screen will display the chosen frequency, as well as the AF and RF reception bars for that channel .

VOL

IR PROGRAM MODE

IR

SET

UHF-8900 UHF PLL WIRELESS SYSTEM

WITH FREQUENCY SCAN 7 . Test the Mic: Speak into the microphone to ensure sound is being produced and transmitted . The AF bars on the LCD should register as the microphone is spoken into.

SET

MENU

VOL

Note: Once the microphone and module are synced, there will be a

5 second delay in audio when the microphone is powered on. This is normal.

8 . Repeat the Process: Repeat steps 3-7 for each of the remaining microphone and modules .

SET

MENU

IR

7

UHF-8900 UHF PLL WIRELESS SYSTEM

WITH FREQUENCY SCAN

6

4

5

15

Re-syncing the Wireless Mics

Occasionally the microphone will need to be re-synced with the respective module. The frequency is the same but the connection between mic and module is lost.

Note: Please read through the steps before attempting to sync the microphones. The module menus have a 4 second timeout period where if a button is not pressed within that time the module will revert back to the frequency information page.

1 . Prepare the system: Ensure the receiver base, the desired module to be paired, and the desired microphone to be paired, are all powered on.

wireless microphone

2 . Identify the IR Sensors: Locate the IR Sensor on both microphone and module .

A.) Microphone - The IR Sensor is located just above the

ON/OFF switch.

B.) Module - The IR Sensor is located directly below the module volume knob.

3

3 . Align the IR Sensors: Position the microphone so that the

2 IR Sensors are level within 3-5 inches of one another.

VOL

UP

SET

MENU

4 . Re-sync Microphone: Press the MENU button on the desired module for time (4x) to cycle the menu to IR mode; this will display the IR symbol. With the IR symbol displayed, press the SET button to communicate the existing frequency to the microphone. This will display waves emanating from the IR symbol, when the waves disappear, the screen will display the existing frequency, as well as the AF and RF reception bars for that channel.

IR

IR MODE

SCAN

UHF-8900

DOWN

VOL

5 . Test the Mic: Speak into the microphone to ensure sound is being produced and transmitted . The AF bars on the

LCD should register as the microphone is spoken into.

SET

MENU

5

Note: Once the microphone and module are synced, there will be a

5 second delay in audio when the microphone is powered on. This is normal.

IR

UHF-8900 UHF PLL WIRELESS SYSTEM

WITH FREQUENCY SCAN

4

16

Using the Wireless Mics

Microphone Position

The UHF-8900 is ideal for close-up vocals and can be held in the hand or mounted on a mic stand. Keep in mind that microphone technique is largely a matter of personal taste, and there is no one “correct” microphone position.

Feedback

Feedback occurs when the amplified sound from any loudspeaker reenters the sound system through any open microphone and is repeatedly amplified.

Most commonly, feedback is caused by the following conditions:

• Placing loudspeakers too close to microphones.

• Having too many open active microphones.

• Boosting tone controls indiscriminately (mainly treble).

• Performing in areas with high ratios of room surfaces that have hard and reflective surfaces such as glass, marble and wood.

What to do if feedback occurs before the sound system is loud enough:

• Request that the talker speak louder into the microphone.

• Reduce the distance from the talker to the microphone. Each time this distance is halved, the sound system output will increase by 6dB.

• Reduce the number of open microphones .

• Move the loudspeaker farther away from the microphone. Each time this distance is doubled, the sound system output can be increased by 6dB .

• Move the loudspeaker closer to the listener.

• Use an equalizer/feedback reducer to cut the frequency bands in which the feedback occurs.

Microphone Placement & Tone Quality

Lead & Backup Vocals

Lips should be less than 3” from or even touching the windscreen on an axis to the microphone. Doing this creates a robust sound, emphasizes bass and provides maximum isolation from other sources.

Speech

When giving a speech or simply speaking, place the microphone 4” to 10” away from the mouth, just above nose height for a natural sound with reduced bass. You can also place the microphone 8” to 16” away from the mouth, slightly off to one side, for a more “distant” sound with highly reduced bass and minimal “s” sounds.

Using the Squelch control

The Squelch control is used to mute unwanted noise interference from a microphone channel when the associated transmitter is turned off. Each channel has its own squelch control and should be set independently as necessary. Squelch can be set from 0 to 15, with 10-15 being represented by A-F.

To adjust squelch:

• For each channel, start with the squelch control set at ‘0’. If not at ‘0’, press and hold the DOWN ARROW until the display reads ‘SQ 0’.

• Press and hold the UP ARROW to increase the squelch

• Press and hold the DOWN ARROW to decrease the squelch.

• You may need to turn the mic on/off to test if the squelch is at a sufficient level.

NOTE: The higher the squelch is set for a particular channel, the shorter the range will be for that mic. At the maximum SQ level, the operational range is approximately 40ft.

17

Basic Operations

Setting Up with Stage Monitors/P.A. System

If you will be using the UHF-8900 with stage monitors and/or a P.A. system, try the following:

• Place the stage monitor directly in front of the microphone .

• Locate the P.A. loudspeakers so that they point away from the rear of the microphone. (With the speakers located in these positions, the possibility of feedback is greatly reduced).

• Always check the stage setup before a performance to ensure optimum placement of microphone and monitors .

PA Speakers Facing Away

From Rear of Microphone

Monitor Directly in

Front of Microphone

NOTE: Every wireless microphone installation is a unique situation, and can present a variety of problems. Never attempt a live performance without first conducting a “walkthrough” test of the system in the performing area. If major changes (additional wireless systems or intercoms, relocation of scenery, etc.) have been made since the last walk-through test, check the wireless system again, as close to performance time as possible .

Avoiding Interference

As with all RF devices, interference can be a problem. While some causes of interference are unavoidable, others can be avoided by taking certain precautions. Below are some helpful hints to avoid unwanted interference.

• Make sure that the operating frequencies used with you wireless system do not coincide with local TV station broadcast frequencies .

• If using multiple systems, or within range of other systems, check all wireless frequencies in use to make sure that no two frequencies are being used at the same time.

• For all operating frequencies, make sure there is at least 1 MHz between each frequency.

• Before using a system in a new location or another city, perform a walk-though to check for new problems.

• Check the squelch control setting on the receiver. A higher squelch setting provides better protection against interference. However, since a high setting also can cause a reduction in operating range, set the control to the lowest position that reliably mutes the interference.

• Make certain that all batteries are fresh and new. Weak batteries make a system more susceptible to interference.

• If not in use, power down electronic equipment such as computers, CD players, and other digital devices, as they are a common source of wireless interference; especially if they are in close proximity to the receiver.

• As much as feasible, keep computers and other digital devices at least 3 feet away from the wireless receiver and/ or its antennas .

Improving Range

To get the most usable range out of your wireless microphone system, follow the helpful hints below.

• Always try to keep an unobstructed line of site between the wireless receiver’s antennas and the wireless transmitters. Metal objects between the wireless transmitters and receiver commonly reduce the operating range.

• When mounting the wireless receiver, avoid mounting it behind other electronic equipment, low to the ground, or in remote equipment/sound rooms.

• As far as feasible, minimize the amount of squelch applied to channels; the higher the squelch setting, the lesser the operating range .

• When operating the wireless system, keep all wireless transmitters at least 10 feet away from the receiver and its antennas. Wireless transmitters in close proximity can overload the receiver and reduce its overall sensitivity, as well as possibly cause interference with other channels on the system.

• Use only high-quality alkaline batteries in the wireless transmitters. Other types of batteries might not provide sufficient voltage and capacity for full power transmission.

• Position the receiver antennas so they do not touch each other.

18

Advanced Operation

Testing a Channel for Outside Interference

Once a microphone and module have been successfully paired, turn the microphone OFF (leave the module ON). With the microphone off, if the RF indicator still has bars showing, there exists interference. Note that RF interference can ebb and flow. Sometimes it may appear as 4 steady bars on the RF indicator, other times, it may weakly occupy a single bar or two.

Generally, we recommend looking for another channel if ANY bars register.

Using the Frequency Scan

In some areas the scan feature may not select an interference-free channel . This is not because the system is malfunctioning, but rather there are no interference-free channels available to choose from in that subgroup. If setting up in this kind, and do not want to use manual frequency selection, we recommend you do the following:

1. Start a Scan (see Setting the Frequencies Automatically for instructions) on the left module (1) using the first group. If there is no open channel in that group, repeat the Scan in the next group. Continue this process until an open channel is selected. (see above for how to test a channel for interference)

2. Begin the Scan process on the second module, but this time start with next available subgroup.

3. Repeat this process with the rest of the modules.

Obtaining Local TV Tower Information

The most common source of RF interference to the UHF-8900 is TV broadcast towers. If the UHF-8900 is experiencing dropouts, static, or other strange noises, it is likely RF interference at fault if within the threshold distance of 30 miles.

Follow the instructions below to obtain the information on your proximity to broadcasting TV towers.

(Applicable to the United States only)

1. Visit www.antennaweb.org (see note below)

2. Select “Click Here to Start”

3. Enter the Zip Code in which the UHF-8900 will be used and hit Submit.

4. The search results page that comes up will contain all the TV broadcasting stations within a 50 mile range.

A.) The information provided for each channel is:

I. Station Name

II . RF Channel - This is the information to be interested in

III. Distance and Heading

5. Write down all of the RF Channel numbers for each of the search results.

Note: Only TV stations within 30 miles would cause issues with the microphones.

6. Refer to the TV Channel Frequency List (page 20) to determine which frequencies not to use.

7. Use the UHF-8900 Frequency List to determine which group and channels that are NOT being interfered with.

Please Note: antennaweb.org is a third party website and is not maintained by nor affiliated with Vocopro.

For example, let’s say you did a search in your area (this example shows zip code 05456) and received the following information:

The only relevant channel is 43, therefore you would jot it down to cross-reference with TV frequency list (page 20)

After cross-referencing, you find that channel 43 uses the frequency range of 644 to 650 MHz. You would NOT choose a frequency that falls in that range .

19

Displaying the Group & Frequency

The module LCD displays all the information regarding the microphone Group (GR) and

Channel (CH). It is important to understand what each icon represents.

Frequency: This is the frequency that the microphone is currently using . It is easier to refer to this as a combination of both Group and Channel numbers .

For example: 655.MHz would be GR 2-1 & CH 01.

Group: The Group number is the subset of frequencies to choose from in each module .

The UHF-8900 displays the module in a few different ways

The top Module row - The groups are listed sequentially starting from GR 01 through

GR 05 .

The bottom Module row (Left 2 Modules) - The Groups are listed as GR 1-1 through

G 1-A

The bottom Module row (Right 2 Modules) - The Groups are listed as GR 2-1 through

GR 2-A .

Channel: This is the number of frequencies in each Group. These are listed the same way in all modules, CH 01 and up.

Please refer to pg. for a complete list of Groups and Frequencies to choose from.

UHF-8900 Frequency List

CH 01

CH 02

CH 03

CH 04

CH 05

CH 06

CH 07

CH 08

GR 01

902.60

906.90

908.05

912.80

914.25

915.95

917.25

925.30

Used by the top 4 modules

GR 02

906.00

904.40

914.90

917.50

919.10

921.85

924.80

926.80

GR 03

903.75

907.60

909.40

916.00

919.50

921.10

923.55

925.60

GR 04

902.70

904.60

908.20

911.95

914.90

922.75

925.40

927.55

20

GR 05

905.00

907.75

909.20

911.05

916.15

922.75

923.85

927.70

UHF-8900 Frequency List

CH 01

CH 02

CH 03

CH 04

CH 05

CH 06

CH 07

CH 08

CH 09

CH 10

CH 11

CH 12

CH 13

CH 01

CH 02

CH 03

CH 04

CH 05

CH 06

GR 1-1

614.000

617.100

621.200

622.200

627.100

628.800

632.100

634.400

638.400

642.200

644.200

644.800

651.900

GR 1-7

632.000

632.500

633.200

634.100

635.500

637.300

GR 1-2

615.000

617.700

623.300

627.400

633.900

641.600

648.600

650.300

GR 1-3

616.300

621.000

627.000

633.300

639.000

646.000

652.600

GR 1-4

614.000

614.500

625.200

616.100

617.500

619.300

GR 1-8

638.000

638.500

639.200

640.100

641.500

643.300

GR 1-9

644.000

644.500

645.200

646.100

647.500

649.300

GR 1-A

650.000

650.500

651.200

652.100

653.500

GR 05

620.000

620.500

621.200

622.100

623.500

625.300

GR 1-6

626.000

626.500

627.200

628.100

629.500

631.300

CH 01

CH 02

CH 03

CH 04

CH 05

CH 06

CH 07

CH 08

CH 09

CH 10

CH 11

CH 12

CH 13

CH 01

CH 02

CH 03

CH 04

CH 05

CH 06

GR 2-1

655.000

658.100

659.300

663.000

664.100

669.100

670.400

675.000

676.600

687.100

688.500

692.500

694.000

GR 2-7

674.000

374.500

675.200

676.100

677.500

679.300

GR 2-2

658.700

660.900

662.400

668.900

677.300

679.200

680.800

684.700

688.300

692.800

GR 2-3

657.600

665.600

672.900

675.000

683.900

686.400

692.300

GR 2-4

656.000

656.500

657.200

658.100

659.500

661.300

GR 2-5

662.000

662.500

663.200

664.100

665.500

667.300

GR 2-6

668.000

668.500

669.200

670.100

671.500

673.300

GR 2-8

680.000

680.500

681.200

682.100

683.500

685.300

GR 2-9

686.000

686.500

687.200

688.100

689.500

691.300

GR 2-A

692.000

692.500

694.400

21

TV Channel Frequencies (USA)

38 614-620 MHz

39 620-626 MHz

40 626-632 MHz

41 632-638 MHz

42 638-644 MHz

43 644-650 MHz

44 650-656 MHz

45 656-662 MHz

46 662-668 MHz

47 668-674 MHz

48 674-680 MHz

49 680-686 MHz

50 686-692 MHz

51 692-698 MHz

Troubleshooting

There is no power

• Make sure the power adapter cord is firmly connected to the back of the UHF-8900 and to the power outlet.

• If using a power strip/surge-protector, make sure that it is plugged in and switched on.

• Make sure the rear panel power switch and the front panel module power switches are turned on.

There is no sound

• Make sure everything is connected firmly and properly.

• Make sure there are no defective cables.

• Make sure all of your components are turned on.

• Make sure all of the components (amp, mixer, TV, etc.) are set to the proper inputs.

• Make sure the microphones are set to the correct channels.

• Make sure the module volume is turned up.

The sound cuts out, is unclear, or has static

• Make sure everything is connected firmly and properly.

• Position the antennas 90º from each other.

• Make sure there are no defective cables.

• Make sure the microphone batteries are fresh and fully charged.

• Increase the squelch on the affected channel.

• Make sure each module is set to a different frequency. Do not assign more than one mic to a module.

• Try a different wireless frequency channel.

Burst of static when turning off a microphone

• Increase the squelch on the affected channel.

• Make sure microphones are at least 1ft from each other.

• Make sure the microphones are at least 5ft from the receiver.

Can’t find an interference free frequency

• Refer to obtaining information on your proximity to TV broadcast towers.

The microphone will not set to the desired frequency

• Make sure the microphone has charged batteries.

• Make sure nothing is blocking the the infrared sensors.

• Hold the microphone closer to the module with the IR sensors facing each other.

• Try a different wireless frequency channel.

Audio from one microphone bleeds into another channel

• Make sure the microphone is at least 10 feet from the receiver.

• Make sure that the mic frequency is at least 1MHz away from the frequencies of the other mics.

Module is stuck in scan mode

• Reset the module by turning it off and on.

Buttons are not responsive

• Make sure the buttons are not stuck.

• Reset the module by turning it off and on.

Commonly Asked Questions

What is Squelch (SQ)?

The Squelch is intended for use against minor signal interference. It should be the first step at troubleshooting a frequency problem. See “Setting the Squelch”.

I turned the mic on but get no AF/RF lights, what’s the deal?

The microphone likely needs to be re-synced with its respective module. See “Re-syncing the Microphones” .

Why is there AF/RF bars showing up when the microphones are turned off?

The LCD display should be clear of both AF/RF bars when the microphones are off. If they’re still there when the mics are off then that would be indicative of an unclear frequency channel. See “Setting the Frequencies Automatically”

(page 14) to find a clear channel, or if being used in a RF-heavy area, see “Setting he Frequencies Manually”.

23

UHF-8900 Owner’s Manual

© VocoPro 2014 v1 .0 .0812

www.vocopro.com

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals