ATEN VE806 User manual

ATEN VE806 User manual
VGA/DVI/HDMI over Cat 5 Extender Wall Plate
VE156 / VE606 / VE806
User Manual
www.aten.com
VE156 / VE606 / VE806 User Manual
EMC Information
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT:
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
CE Warning: This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
Suggestion: Shielded twisted pair (STP) cables must be used with the unit to ensure
compliance with FCC & CE standards.
RoHS
This product is RoHS compliant.
SJ/T 11364-2006
The following contains information that relates to China.
ii
VE156 / VE606 / VE806 User Manual
User Information
Online Registration
Be sure to register your product at our online support center:
International
http://eservice.aten.com
Telephone Support
For telephone support, call this number:
International
886-2-8692-6959
China
86-10-5255-0110
Japan
81-3-5615-5811
Korea
82-2-467-6789
North America
1-888-999-ATEN ext 4988
United Kingdom
44-8-4481-58923
User Notice
All information, documentation, and specifications contained in this manual
are subject to change without prior notification by the manufacturer. The
manufacturer makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties as to merchantability or fitness for any particular purpose. Any of
the manufacturer's software described in this manual is sold or licensed as is.
Should the programs prove defective following their purchase, the buyer (and
not the manufacturer, its distributor, or its dealer), assumes the entire cost of all
necessary servicing, repair and any incidental or consequential damages
resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV
interference caused by unauthorized modifications to this device. It is the
responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation
of this system if the correct operational voltage setting was not selected prior
to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS
CORRECT BEFORE USE.
iii
VE156 / VE606 / VE806 User Manual
Package Contents
The VGA/DVI/HDMI over Cat 5 Extender Wall Plate package contains the
following items:
Š 1 VE156T / VE606T / VE806T VGA/DVI/HDMI over Cat 5 Extender
Wall Plate
Š 1 VE156R / VE606R / VE806R VGA/DVI/HDMI over Cat 5 Extender
Wall Plate
Š 1 Terminal Block Connector
Š 1 Power Adapter
Š 1 User Instructions*
Check to make sure that all the components are present and that nothing got
damaged in shipping. If you encounter a problem, contact your dealer.
Read this manual thoroughly and follow the installation and operation
procedures carefully to prevent any damage to the unit, and/or any of the
devices connected to it.
* Features may have been added to the VE156 / VE606 / VE806 since this
manual was published. Please visit our website to download the most up-todate version.
© Copyright 2014 ATEN® International Co., Ltd.
Manual Date: 2014-7-3
ATEN and the ATEN logo are registered trademarks of ATEN International Co., Ltd. All rights reserved.
All other brand names and trademarks are the registered property of their respective owners.
iv
VE156 / VE606 / VE806 User Manual
Contents
FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
SJ/T 11364-2006. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
1. Introduction
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Front View (Transmitter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Front View (Receiver) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Rear View (Transmitter / Receiver) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2. Hardware Setup
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Before Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Wall Box Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Power Supply Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3. Basic Operation
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Picture Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Appendix
Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
International. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
v
VE156 / VE606 / VE806 User Manual
About this Manual
This User Manual is provided to help you get the most from your system. It
covers all aspects of installation, configuration and operation. An overview of
the information found in the manual is provided below.
Chapter 1, Introduction, introduces you to the VE156 / VE606 / VE806
system. Its purpose, features and benefits are presented, and its front and back
panel components are described.
Chapter 2, Hardware Setup, describes how to set up your installation. All
necessary steps to prepare for operation are provided.
Chapter 3, Basic Operation, describes how to adjust the picture quality.
An Appendix, provides specifications and other technical information
regarding the VE156 / VE606 / VE806.
vi
VE156 / VE606 / VE806 User Manual
Conventions
This manual uses the following conventions:
Monospaced
Indicates text that you should key in.
[]
Indicates keys you should press. For example, [Enter] means to
press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].
1.
Numbered lists represent procedures with sequential steps.
♦
Bullet lists provide information, but do not involve sequential steps.
→
Indicates selecting the option (on a menu or dialog box, for
example), that comes next. For example, Start → Run means to
open the Start menu, and then select Run.
Indicates critical information.
Product Information
For information about all ATEN products and how they can help you connect
without limits, visit ATEN on the Web or contact an ATEN Authorized
Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:
International
http://www.aten.com
North America
http://www.aten-usa.com
vii
Chapter 1
Introduction
Overview
The VGA/DVI/HDMI over Cat 5 Extender Wall Plate extends VGA/DVI/
HDMI and audio signals up to 150 m (for VE156) / 60 m (for VE606 / VE806)
using Cat 5e cables. It supports popular wide screen formats and ensures
excellent video quality over long distance transmissions. The VE156 / VE606
/ VE806, in combination with other ATEN devices such as VGA/DVI/HDMI
extenders and MDS solutions, can further extend the distance or multiply A/V
sources/displays.
The VE156 / VE606 / VE806 can be powered at either the Transmitter or
Receiver side, and uses a second Cat 5e cable to transmit the power signal to
the other unit. The compact wall plate design does away with bulky cables and
allows a neat and convenient installation. It is an ideal solution for function
rooms, museums and any environment that requires equipment or cabling to be
kept hidden from public view.
1
Introduction
Features
Š Uses two Cat 5e cables to connect the local and remote units – one to
transmit video and audio; and another for power*
Š Remotely powered from either the Transmitter or Receiver side**
Š Extends the distance between VGA/DVI/HDMI source and VGA/DVI/
HDMI display
Š Superior video quality – VE156: up to 1920 x 1200 @60Hz (30 m), 1280 x
1024 @ 60Hz (150m); VE606 / VE806: 1080p @ 60Hz (40m), 1080i @
60Hz (60m)
Š Adjustable Video Compensation Control – manually adjusts signal
strength to compensate for distance (VE156)
Š 8-segment equalization adjustment switch optimizes display quality
(VE606 / VE806)
Š Compatible with existing ATEN VGA/DVI/HDMI extenders – see
page 18 for more information
Š Supports wide screen formats
Š Supports hot-plugging
Š Decora type design is easily configurable to fit various wall plates
Š HDMI (3D, Deep Color); HDCP compatible (VE806)
Š LED indication of power sources / connection status
Š Supports stereo audio
Š Built-in 8KV/15KV ESD protection
Š A neat and cleaner installation via easy wall-mounting
Š Plug-and-play – no software installation required
Note: * The second Cat 5e cable connection is required to remotely power on
either the Transmitter or Receiver. For VE606 / VE806, it is also
required for real EDID Bypass and HDCP key authentication.
** A power adapter is provided with this package, and can be used at
either the Transmitter or Receiver side, which in turn remotely powers
the other unit. See How to Supply Power, page 9.
2
VE156 / VE606 / VE806 User Manual
Requirements
Console
Š A display with an HDB-15 Male connector (for VE156)
Š A display with an DVI Male connector (for VE606)
Š A display with an HDMI Male connector (for VE806)
Š Speakers (optional)
Computer
Š Video source with an HDB-15 Male connector (for VE156)
Š Video source with an DVI Male connector (for VE606)
Š Video source with an HDMI Male connector (for VE806)
Š Audio port (optional)
Cables
Š Cat 5e cables
Š VGA / DVI / HDMI cable(s)
Š Audio cable (optional)
Note: No cables are included in this package. It is strongly recommended that
you purchase high-quality cables of the required lengths to ensure the
quality of the audio and video display. Contact your dealer for more
information about the correct cable sets.
3
Introduction
Components
Front View (Transmitter)
VE606T
VE156T
VE806T
3
3
1
1
1
2
2
No.
3
Component
2
Description
1
Video IN Port
The cable from your VGA / DVI / HDMI source device is
plugged in here.
2
Power LED
The Power LED lights green to indicate that the unit is
receiving power.
3
Audio IN Port
The cable from your audio source device is plugged in here.
Front View (Receiver)
VE606R
VE156R
3
1
Component
3
3
1
1
4 2
No.
VE806R
4 2
4 2
Description
1
Video OUT Port
The cable from your VGA / DVI / HDMI monitor plugs in
here.
2
Power/Link LED
The Power LED lights green to indicate that the unit is
receiving power.
The Link LED lights orange to indicate that the connection
to the Transmitter unit has been established.
3
Audio OUT Port
The cable from your speakers plugs in here.
4
Manual Gain Control
(VE156) /
Use this knob to adjust the video quality by turning to the
right or left until you obtain the desired picture quality.
EQ Switch (VE606 /
VE806)
See Picture Adjustment, page 14 for more details.
4
VE156 / VE606 / VE806 User Manual
Rear View (Transmitter / Receiver)
2
1
4
3
No.
1
Component
Description
Line IN/OUT (VE156)
The Cat 5e cable that connects the Transmitter
TMDS Port (VE606 / VE806) and Receiver units plugs in here. The Cat 5e
connection between these ports transmits video
and audio signals.
For VE156:
Š Transmitter (Line OUT)
Š Receiver (Line IN)
2
Power (Terminal block)
The power adapter wires (+9V and GND) plug in
here.
See How to Supply Power, page 9 for the steps
on how to connect the terminal block to a power
source.
3
Power Port (VE156)
DDC Port (VE606 / VE806)
Use a Cat 5e cable to connect the Transmitter
and Receiver units through this port.
The second Cat 5e cable connection transmits the
power signal to either the Transmitter or Receiver
when only one of the units is supplied power via
the Terminal Block.
For VE606 / VE806, in addition to transmitting the
power signal, the second Cat 5e cable is used for
real EDID Bypass and HDCP key authentication.
4
Grounding Terminal
The grounding wire is attached here.
Note: The grounding wire is not included in this
package.
5
Introduction
This Page Intentionally Left Blank
6
Chapter 2
Hardware Setup
1. Important safety information regarding the placement of this
device is provided on page 15. Please review it before
proceeding.
2. Make sure that the power to all devices connected to the
installation is turned off. You must unplug the power cords of
any computers that have the Keyboard Power On function.
Overview
For convenience and flexibility, the VE156 / VE606 / VE806 can be mounted
on the wall, ceiling, floor or any surface of your preference.
The dimensions of the VE156 / VE606 /
VE806 are made to fit both a standard onegang wall box and a single-gang mud ring,
which can be purchased at a hardware
store.
6.73 cm
11.43 cm
For a neat finish, use a decora face plate as
a cover. The image on the right shows the
VE156 / VE606 / VE806 fitted with a
decora face plate with a rectangular
opening that fits the unit’s dimensions
(6.73 cm length x 3.38cm width).
3.38 cm
After mounting the VE156 / VE606 /
VE806, you can proceed to the Hardware
Installation on page 12.
7.09 cm
Note: This chapter uses the VE156 panels for illustrating the installation steps.
7
Hardware Setup
Before Mounting
In order to mount the VE156 / VE606 / VE806, you first need to purchase: a
standard single-gang Decora Face Plate, and either one of the following:
Š Single-gang Mud Ring
Š One-gang Wall Box
Note: The VE156 / VE606 / VE806 package does not include a mounting kit.
Prepare two installation sites (for the Transmitter and Receiver units) with the
proper dimensions (see image below) to accommodate the Mud Ring or Wall
Box.
Make sure proper cabling (unit-to-unit via Cat 5e; unit-to-power) can be
supplied to both sites.
Wall Box Dimensions
The installation site or wall box should have a minimum depth measurement of
6.35 cm, as shown in the figure below.
6.35 cm
Front
Panel
4.62 cm
8
VE156 / VE606 / VE806 User Manual
How to Supply Power
One pair of Power Adapter and Terminal Block Connector is provided in this
package, and can be used on either the Transmitter or Receiver side. The
second Cat 5e cable connection transmits the power signal.
Note: To supply power to each unit separately, you must purchase another set
of power adapter (within a voltage range of +9V~12V) and terminal
block connector. In this case, there is no need to connect the second Cat
5e cable.
The provided Power Adapter and Terminal Block Connector must be
combined. You can then use the modified power adapter to connect – first, to
the terminal block on either the VE156T / VE606T / VE806T or VE156R /
VE606R / VE806R rear panel; and then, to a power outlet to supply power to
your VE156 / VE606 / VE806. Follow the steps described below:
1. Cut off the connector end of the
power adapter.
2. Strip 5mm (0.5 cm) off the
insulation cover of the Power
Adapter cable to expose two wires:
a +9V wire and a GND
(grounding) wire.
The exposed wires must constantly be separated
from each other to prevent any unexpected
damage (including short-circuits, electric shocks,
and so on.)
3. Insert the exposed +9V wire and
GND wire tightly into the provided
2-pin Terminal Block Connector.
The connector is properly labeled –
the +9V and GND wires should be
plugged into the correct holes.
Provided
Connector
(-)
(+)
(Continues on next page.)
9
Hardware Setup
Note: The device can be damaged if incorrectly paired wires are inserted into
the terminal block. A voltmeter is one of the tools used to measure an
exposed wire’s polarity (i.e., +9V or GND).
4. Connect and snap the Terminal Block
Connector into the 2-pin Terminal Block
located on either the Transmitter or
Receiver unit’s rear panel.
5. Connect the other end of the power adapter
to a power socket.
Note: If you wish to use another external
power supply, ensure that it stays
within a voltage range of +9V~12V.
10
VE156 / VE606 / VE806 User Manual
Wall Mounting
At this point, the site(s) for wall-mounting the VE156 / VE606 / VE806 should
be ready. Note that there are cable connections to be made at the rear panel of
the units – see Hardware Installation.
1. Screw the Mud Ring or the Wall Box to the installation site (wall, ceiling,
and so on).
2. Attach the VE156 / VE606 / VE806 unit to the Mud Ring or Wall Box.
Screw the units accordingly.
Mounting
with a Mud Ring
Mounting
with a Wall Box
3. After making the necessary unit-to-unit Cat 5e cable connections, as well
as the terminal block connection (optional), attach the Decora Face Plate
to secure and cover the VE156 / VE606 / VE806.
11
Hardware Setup
Hardware Installation
After mounting the VE156 / VE606 / VE806 Transmitter and Receiver units,
you can conveniently connect the VE156 / VE606 / VE806 decora face plate
installation to your input/output equipment. Refer to the installation diagram
on the following page (the numbers in the diagrams correspond to the steps
below), and do the following:
1. Connect the Video IN Port on the VE156T / VE606T / VE806T
(Transmitter) to the Video OUT port on your video source device.
2. Connect one end of the audio cable to the Audio IN port of the VE156T /
VE606T / VE806T and connect the other end to the Audio OUT port of
the source device.
3. Connect the Video OUT port on the VE156R / VE606R / VE806R
(Receiver) to the Video IN port on your video display device using the
VGA/DVI/HDMI cable that came with your display device.
4. Connect your speakers to the Audio OUT port on the VE156R / VE606R /
VE806R.
5. Connect the Transmitter or Receiver to a power outlet using the provided
terminal block connector / power adapter – see How to Supply Power,
page 9.
6. Connect one end of the Cat 5e cable to the Line OUT port (VE156T) /
TMDS port (VE606T / VE806T) on the Transmitter unit. Connect the
other end of the Cat 5e cable to the Line IN port (VE156R) / TMDS port
(VE606R / VE806R) on the Receiver unit.
7. (Optional) Use a second Cat 5e cable to connect the Power ports (VE156T
/ VE156R) / DDC ports (VE606T / VE606R / VE806T / VE806R).
Note: 1. A second Cat 5e cable connection is required only if you need to
transmit power to either Transmitter or Receiver.
2. For VE606 / VE806, in addition to the above, a second Cat 5e
cable is only required if you need to use real EDID Bypass and
HDCP key authentication.
8. Power on your source and display devices.
12
VE156 / VE606 / VE806 User Manual
FRONT
REAR
22
35
12
Cat 5e Cable
FRONT
42
REAR
35
33
13
Chapter 3
Basic Operation
Overview
This chapter describes the Manual Gain Control / EQ switch located on the
front panel of the Remote Unit that adjusts the VGA / DVI / HDMI display to
obtain the best video quality.
Picture Adjustment
The quality of the video signal can decrease with distance. To adjust the video
quality, do the following:
Š VE156 – Use the Manual Gain Control switch by turning the knob
clockwise to increase the video signal, or turning the knob counterclockwise to decrease the video signal – until you obtain the desired
picture quality.
Š VE606 / VE806 – Use the EQ switch to adjust the equalization strength
and improve a blinking image.
The Equalization values range from 0-7 where:
Š 7: strongest equalization
Š 0: weakest equalization
14
Appendix
Safety Instructions
General
Š Read all of these instructions. Save them for future reference.
Š Follow all warnings and instructions marked on the device.
Š This product is for indoor use only.
Š Do not place the device on any unstable surface (cart, stand, table, etc.). If
the device falls, serious damage will result.
Š Do not use the device near water.
Š Do not place the device near, or over, radiators or heat registers.
Š The device cabinet is provided with slots and openings to allow for
adequate ventilation. To ensure reliable operation, and to protect against
overheating, these openings must never be blocked or covered.
Š The device should never be placed on a soft surface (bed, sofa, rug, etc.) as
this will block its ventilation openings. Likewise, the device should not be
placed in a built in enclosure unless adequate ventilation has been provided.
Š Never spill liquid of any kind on the device.
Š Unplug the device from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
Š The device should be operated from the type of power source indicated on
the marking label. If you are not sure of the type of power available,
consult your dealer or local power company.
Š The device is designed for IT power distribution systems with 230V
phase-to-phase voltage.
Š To prevent damage to your installation it is important that all devices are
properly grounded.
Š The device is equipped with a 3-wire grounding type plug. This is a safety
feature. If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not attempt to defeat the
purpose of the grounding-type plug. Always follow your local/national
wiring codes.
Š Do not allow anything to rest on the power cord or cables. Route the
power cord and cables so that they cannot be stepped on or tripped over.
15
Appendix
Š If an extension cord is used with this device make sure that the total of the
ampere ratings of all products used on this cord does not exceed the
extension cord ampere rating. Make sure that the total of all products
plugged into the wall outlet does not exceed 15 amperes.
Š To help protect your system from sudden, transient increases and
decreases in electrical power, use a surge suppressor, line conditioner, or
un-interruptible power supply (UPS).
Š Position system cables and power cables carefully; Be sure that nothing
rests on any cables.
Š Never push objects of any kind into or through cabinet slots. They may
touch dangerous voltage points or short out parts resulting in a risk of fire
or electrical shock.
Š Do not attempt to service the device yourself. Refer all servicing to
qualified service personnel.
Š If the following conditions occur, unplug the device from the wall outlet
and bring it to qualified service personnel for repair.
Š The power cord or plug has become damaged or frayed.
Š Liquid has been spilled into the device.
Š The device has been exposed to rain or water.
Š The device has been dropped, or the cabinet has been damaged.
Š The device exhibits a distinct change in performance, indicating a need
for service.
Š The device does not operate normally when the operating instructions
are followed.
Š Only adjust those controls that are covered in the operating instructions.
Improper adjustment of other controls may result in damage that will
require extensive work by a qualified technician to repair.
16
VE156 / VE606 / VE806 User Manual
Technical Support
International
Š For online technical support – including troubleshooting, documentation,
and software updates: http://eservice.aten.com
Š For telephone support, see Telephone Support, page iii:
North America
Email Support
Online
Technical
Support
[email protected]
Troubleshooting
Documentation
Software Updates
Telephone Support
http://www.aten-usa.com/support
1-888-999-ATEN ext 4988
When you contact us, please have the following information ready beforehand:
Š Product model number, serial number, and date of purchase.
Š Your computer configuration, including operating system, revision level,
expansion cards, and software.
Š Any error messages displayed at the time the error occurred.
Š The sequence of operations that led up to the error.
Š Any other information you feel may be of help.
17
Appendix
Supported ATEN Products
The VE156 / VE606 / VE806 Transmitter and Receiver can each be used
separately with other VGA/DVI/HDMI extenders, as follows:
VE156
VE022
VE606
VE806
VE170
VS1204T
VS1208T
VE600A
VE800
VS1804T
VS1808T
18
VE156 / VE606 / VE806 User Manual
Specifications
Connectors
Function
VE156T
VE156R
Video In
1 x HDB-15 Female
(Blue)
N/A
N/A
1 x HDB-15 Female
(Blue)
1 x 3.5mm Stereo
Jack (Green)
N/A
N/A
1 x 3.5mm Stereo
Jack (Green)
Video Out
Audio In
Audio Out
Power
Power
1 x Terminal Block (Green)
Line In
N/A
1 x RJ-45 Female
(Silver)
1 x RJ-45 Female
(Silver)
N/A
Line Out
LED
Power
Link
Switch
Manual Gain Control
Video
Environment Operating Temp.
Storage Temp.
Humidity
1 (Amber)
N/A
1 x Knob
DC 9V, 3.2W
0–50ºC
-20–60ºC
0–80% RH, Non-condensing
Housing
Metal
Weight
0.17 kg
Dimensions (L x W x
H)
19
1 (Green)
N/A
1920 x 1200 @ 60 Hz (30 m)
1280 x 1024 @ 60 Hz (150 m)
Power Consumption
Physical
Properties
1 x RJ-45 Female (Silver)
10.41 x 4.40 x 4.40 cm
Appendix
Connectors
Function
VE606T
VE606R
Video In
1 x DVI-D Female
(White)
N/A
N/A
1 x DVI-D Female
(White)
1 x 3.5mm Stereo
Jack (Green)
N/A
N/A
1 x 3.5mm Stereo
Jack (Green)
Video Out
Audio In
Audio Out
DDC
1 x RJ-45 Female (Silver)
Power
1 x Terminal Block (Green)
TMDS
1 x RJ-45 Female (Silver)
LED
Power / Link
Switch
EQ Switch
Video
N/A
1 x Knob
1080p @ 60 Hz (40m)
1080i @ 60 Hz (60m)
Power Consumption
Environment Operating Temp.
Storage Temp.
Humidity
Physical
Properties
1 (Green / Amber)
DC 9V, 2.9W
0–50ºC
-20–60ºC
0–80% RH, Non-condensing
Housing
Metal
Weight
0.17 kg
Dimensions (L x W x
H)
10.41 x 4.40 x 4.34 cm
20
VE156 / VE606 / VE806 User Manual
Connectors
Function
VE806T
VE806R
Video In
1 x HDMI Type A
Female (Black)
N/A
N/A
1 x HDMI Type A
Female (Black)
1 x 3.5mm Stereo
Jack (Green)
N/A
N/A
1 x 3.5mm Stereo
Jack (Green)
Video Out
Audio In
Audio Out
DDC
1 x RJ-45 Female (Silver)
Power
1 x Terminal Block (Green)
TMDS
1 x RJ-45 Female (Silver)
LED
Power / Link
Switch
EQ Switch
Video
N/A
1 x Knob
1080p @ 60 Hz (40m)
1080i @ 60 Hz (60m)
Power Consumption
Environment Operating Temp.
Storage Temp.
Humidity
Physical
Properties
1 (Green / Amber)
DC 9V, 2.9W
0–50ºC
-20–60ºC
0–80% RH, Non-condensing
Housing
Metal
Weight
0.17 kg
Dimensions (L x W x
H)
10.41 x 4.40 x 4.00 cm
Limited Warranty
IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY EXCEED THE PRICE PAID
FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, DISK,
OR ITS DOCUMENTATION.
The direct vendor makes no warranty or representation, expressed, implied, or statutory with
respect to the contents or use of this documentation, and especially disclaims its quality,
performance, merchantability, or fitness for any particular purpose.
The direct vendor also reserves the right to revise or update the device or
documentation without obligation to notify any individual or entity of such
revisions, or update. For further inquiries, please contact your direct vendor.
21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement