Eurotech EDW194E User`s manual

Eurotech EDW194E User`s manual
IMPORTANT INFORMATION
Revised Dishwasher
Installation Instructions
To obtain a revised copy of the entire
Dishwasher User’s Manual, go to
www.eurotechappliances.com.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
SPECIAL EDITION 11-20-02
INSTALLATION INSTRUCTIONS
Read these instructions carefully and completely before you install the machine. The installation should be
carried out by a qualified person who is familiar with all local codes and ordinances for electrical and
plumbing connections.
If a dishwasher is being installed in this area for the first time, most of the cabinet work, plumbing, and
electrical has to be done before you move the machine into place.
If you are replacing an old dishwasher, you must check the plumbing connection and wiring before you
move the new dishwasher into place.
A built-in dishwasher must be enclosed on the top, both sides and the back. The best place for your dishwasher
is in the kitchen near the sink. This makes it easier to connect the water and drain supply lines.
After you have placed the dishwasher near the installation location, remove the wrappings from the dishwasher.
Be sure to remove any items packaged inside the dishwasher.
NOTE: It is a good idea to inspect for any shipping damage before you proceed with the installation.
Should you find any damage, you should report it to your dealer or builder immediately.
WHAT YOU NEED
TOOLS
1)
2)
3)
4)
5)
6)
7)
8)
Phillips No. 2 screwdriver or power screwdriver (preferably with magnetic screw bits)
Adjustable 10” crescent wrench
Open-ended wrench (1/2", 3/8” and 5/8")
Tape measure
Spirit level
Electric drill with 1-1/2”” drill bit or hole saw (for new installations)
Keyhole saw
2-1/2” Squeeze Clamps (for EDW194E door panel installation only)
MATERIALS NEEDED
♦ Shut-off valve and fittings for water supply line
MATERIALS SUPPLIED WITH UNIT
The items illustrated below are packaged inside each unit for your convenience.
Hardware Package
Contents
1) Warrranty card
2) Data plate/serial card
3) Cutlery caddy cover *
4) Moisture barriers (2)
5) Drain hose high loop support
6) Hardware package
7) Slide cups for levelling legs
8) Owner's Manual
9) Top fill strip for EDW194E
*Not with EDW132C
2
Two 1-1/8” screws
with sleeves
Four 3/4” screws
Four 1-1/2” screws
One rubber washer
CABINET OPENING DIMENSIONS
After determining where the water supply line
will enter under the sink, drill a 1-1/2" (38 mm)
access hole. The water line inlet valve is on
the right rear of the machine.
32" to 35"
813 to 890 mm
The electrical and water supplies should
enter through the area indicated by the shading
on the illustration at right. They should come
through the right side of the machine, a
maximum of 2” (50 mm) from the back wall
and 6-1/4” to 8-1/4” (159–210 mm) from the
floor, depending on the underneath cabinet
height.
2"
50 mm
6-1/4" to 8-1/4"
159 to 210 mm
23
60 -15
8 /16
m
m "
Height
Width
Depth
Measurements
US
Metric
32"–35"
813–890 mm
24"
610 mm
23-15/16"
608 mm
24"
610 mm
MOISTURE BARRIER
Among the materials supplied with your unit are two strips of moisture resistant material (moisture barriers).
One of these is intended to be affixed underneath the front edge of the cabinet to prevent possible moisture
damage. The other is for a custom wood panel (EDW194E only).
If you intend to use a moisture barrier on the cabinet, you should affix it to the cabinet before you install the
dishwasher.
INSTALLING THE TOP FILL STRIP ON MODEL EDW194E
If you have Model EDW194E, you will need to install the fill strip before you place the dishwasher inside the
cabinet. To do this, follow the instructions below:
1. Center the fill strip on top of the installation lip on the front edge of the unit.
2. If the fill strip is wider than the cabinet opening, use a coarse sandpaper or straight edge hack saw to trim
one end.
3. Using 2-1/2” squeeze clamps, secure the fill strip to the installation lip, as illustrated below.
4. Fasten the fill strip to the dishwasher using the four 3/4” screws supplied with the unit in the holes on the
installation lip.
5. Remove the clamps.
3
ADJUSTING THE LEVELING LEGS
Before you slide the unit under the cabinet, you should adjust the
levelling legs to within 1/8” of the opening height. The four leveling
legs should be adjusted by unscrewing the leg out to the length
required.
The final height adjustment should be made after the unit is in place
under the cabinet. When the feet are properly adjusted, tighten the
locking nuts to the base pan.
(The machine may have an inclination of 2° maximum without
affecting its performance.)
WARNING!
Levelling leg
Never lay the dishwasher on its front or
side. When necessary, lay the unit on its
back.
It is advisable to lay the unit on a tarp or
blanket so as not to scratch or damage
the floor or the dishwasher.
Locking nut
MOVING THE MACHINE INTO PLACE
WARNING!
Make sure you put the slides cups under the legs to prevent damaging the
floor or unit when you slide it into place (see page 6).
1. Remove the zip tie holding the hoses and power supply cord in place
on the back of the unit, as illustrated at right.
2. Position the machine in front of the cabinet opening.
3. Pull out the drain hose to ensure there are no sharp bends.
4. Start to feed water, drain lines, and electric cord (if necessary) into
the access hole in the cabinet.
5. Grip the unit at the top or side edges and gently slide the unit into the
dishwasher opening using the slide cups provided with the unit.
WARNING!
Never use your knee or shoulder to push
the unit in place. You could damage the
dishwasher.
6. Check the level and make adjustments if necessary. (See above.)
WARNING! Be careful of sharp edges.
OPENING THE EDW194E CUSTOM DOOR
To open the door panel on the EDW194E, insert your fingers into the
rectangular slots on each side of the door and pull.
4
FASTENING THE DISHWASHER TO THE CABINET
It’s necessary to fasten the dishwasher to the cabinet so it won’t tilt when the door is opened or if something
heavy is placed on the door. Use only the screws provided with the machine. The dishwasher can be
fastened to the cabinet on the top, at the sides, or both, depending on the type of installation.
STANDARD CABINET INSTALLATIONS
For a standard cabinet installation, you should mount the dishwasher
at the top. To do this, follow the instructions below:
1. Use the four 3/4” screws provided with the unit to mount the
dishwasher to underneath the cabinet top.
2. Insert the screws through the four holes on the top installation lip
and tighten securely.
3. When the machine is properly attached, check that the feet are
tight against the floor and the machine is level.
Top Fastening
This method is for standard
installations only.
SOLID SURFACE COUNTER TOP INSTALLATIONS
If you have a solid surface countertop that will not accommodate screws, mount the dishwasher to the
cabinet using the side mount holes. To do this, follow the instructions below:
1. Remove the white plugs from the side holes and use a “center
punch” to assist in starting the screws.
2. Insert the two mounting screws with sleeves provided with the
unit into the side holes and tighten the screw securely.
3. Cover the screw heads with the plastic plugs provided with the
machine.
4. When the machine is properly attached, check that the feet are
tight against the floor and that the machine is level.
Side Fastening
Use this method only for solid surface
counter tops, such as marble.
EDW194E WITH A TOP FILL STRIP INSTALLATIONS
Model EDW194E installations with a top fill strip should be mounted to the cabinet on the sides.
NOTE: Do not fasten the dishwasher to the cabinet until after you have installed the custom door panel.
To do this installation, follow the steps below:
1. Install the fill strip as explained on page 6.
2. Remove the white plugs from the side holes and use a “center
punch” to assist in starting the screws.
3. Insert the two mounting screws with sleeves provided with the
unit into the side holes and tighten securely.
4. Cover the screw heads with the plastic plugs provided with the
machine.
5. When the machine is properly attached, check that the feet
are tight against the floor and that the machine is level.
Top fill strip
Side Fastening
Model EDW194E
This method is for EDW194E
installations with a top fill strip.
INSTALLING THE TOE KICK
You will have to adjust the toe kick bracket depth to allow for the thickness of the toe kick. To do this, first measure
the thickness of the toe kick. Then press the spring tab on the sides of the base pan toward the outside of the
machine and carefully pull or push the bracket to the required depth less the thickness of the toe kick.
Make sure the toe kick bracket is securely inside the guides on the base pan.
Once you have adjusted the toe kick bracket to the desired depth, you can install
the toe kick, as follows:
1. If you have not done so, remove the toe kick from inside or on top of the unit.
2. Positioning the toe kick at the edge of the access panel, slide the toe kick up
behind the access panel then let it slide to the floor.
3. Screw the toe kick to the toe kick brackets.
5
TECHNICAL DATA
Water pressure
Power
Heating element
Max loading
18-176 psi
110–120 v, 60 Hz
1200 w
1450 w
EASY CONNECTION
Your Eurotech comes with everything you need for an easy, problem-free installation:
n
PEX tubing with 3/8” compression fitting—This tubing has a 50-year spec life. It fits American
dishwasher water supply valves.
n
Drain hose—Corrugated drain hose and holder to form a high loop.
n
Electrical cord and plug—110-120 volts, 15 amp cord supplied with unit.
WARNING! Do not use an extension cord for this appliance.
WATER SUPPLY
WARNING!
Plumbing connections must comply with applicable sanitary, safety and
plumbing codes in your area.
The dishwasher comes with a 5-foot PEX water supply line that has a 3/8" NPT female connection. Be sure
to insert the black rubber washer (enclosed in the hardware package) into the PEX hose connection
before you attach it to the water supply.
The electrical and water supplies should come through the right side of the machine, a maximum of 2” (50
mm) from the back wall and 6-1/4” to 8-1/4” (159–210 mm) from the floor, depending on the underneath
cabinet height.
For service convenience, a shut-off valve (not supplied) should be installed in the water supply line in an
easily accessible location, such as, beneath the sink.
It is important that the water supply line and the shut-off valve have a sufficient flow volume. At least 3
gallons (12 liters) per minute must be able to pass through the line. The water pressure should be 18-176
psi.
WARNING!
In order to prevent heat damage to the inlet valve, all solder connections
must be made before the water line is connected to the dishwasher.
NOTE: Be sure to run the PEX water supply
line, drain line, and power supply
cord through the hole to sink
compartment before moving the
dishwasher into position.
6
(1)
Water supply
(2)
Water supply valve (not supplied)
DRAIN CONNECTIONS
Eurotech provides a 5/8” (17 mm) corrugated drain hose with a drain line holder to form a high loop. If
additional drain hose is needed, please purchase an additional Eurotech drain hose and join it to the provided
hose with a 5/8” (17 mm) copper tube.
NOTE: Do not use any fittings anywhere in the drain line that are less than 5/8" (17 mm) ID.
The access hole for the drain line should be 1-1/2" (38 mm).
The high loop is necessary for proper draining and should be located as close to the dishwasher as possible.
There are three ways to connect the drain supply line, as shown
in the illustrations at right:
A) Typical connection to sink plumbing
before trap (high loop drain)
A) Typical connection to sink plumbing before trap (high loop
drain)
B) Connection to air gap then to the trap.
C) Connection to waste disposer with air gap
NOTE: Don’t forget to remove the knockout or plug
from the disposer fitting.
IMPORTANT THINGS TO KNOW ABOUT DRAIN
CONNECTIONS:
♦ Failure to provide the proper drain connection height
(minimum of 20" (508 mm)) above the bottom of the dishwasher base) or a 20" (508 mm) high loop will
result in improper drainage, which will damage the machine.
B) Connection to air gap then to the trap.
♦ No part of the drain hose should be higher than 35" (889
mm) from the bottom of the dishwasher.
♦ The hose must not be drawn straight to a floor well or its
equivalent because it might function as a siphon and empty
the machine.
♦ The drain hose can be extended to a maximum length of 10
feet (3048 mm). Joints and jointed tubes, if any, must have a
minimum 5/8" (17 mm) ID.
♦ If the drain line is going to be connected to a waste disposer,
be sure to remove the knockout or plug from the fitting on
the disposer before connecting the drain line.
When the installation is ready, open the supply valve and let
the pressure act for a while. Then check that all connections
are tight and there are no leaks.
10
C) Connection to waste disposer with air gap.
ELECTRICAL CONNECTIONS
The dishwasher comes with an electrical cord for 110–
120 volts, 15 amp supplied. This cord should be plugged
into the 110-120 volt outlet under the sink. If the cord is
not long enough, or if a hard-wire installation is needed,
see “Connecting An Electrical Cable” below.
WARNING! Do not use an extension cord for
this appliance.
The power-supply receptacle for the appliance should
be installed in a cabinet or on a wall adjacent to the
undercounter space in which the appliance is to be
installed.
There should be an opening through the partition
between the opening for the dishwasher and the area under the sink that is large enough for the power cord
to pass through. This opening should not be more than 1-1/2” (38 mm) in diameter and the edges should be
smooth and rounded. If the partition is metal it should be covered with an edge protector provided for this
purpose by the manufacturer.
When moving the appliance into or out of the cabinet, be careful not to damage the power-supply cord.
WARNING!
WARNING!
WARNING!
Before working on wiring for any electrical appliance, be sure the electrical
power has been turned off at the breaker/fuse box.
Disconnect electrical power supply and place a tag at the disconnect
switch indicating that you are working on the circuit.
Electrical and grounding connections must comply with the applicable
portions of the national electrical code and/or other local electrical codes.
GROUNDING INSTRUCTIONS
WARNING!
This appliance must be properly grounded.
A) Grounding instructions for a grounded, cord-connected appliance
In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a
path of least resistance for electric current. This appliance is equipped with a cord having an equipmentgrounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local codes and ordinances.
WARNING!
Improper connection of the equipment-grounding conductor can result in a
risk of electric shock. Check with a qualified electrician or service
representative or personnel if you are in doubt as to whether the appliance
is properly grounded. Do not modify the plug provided with the appliance.
If it will not fit the outlet, have a proper outlet installed by a qualified
electrician.
B) Grounding instructions for a permanently connected appliance:
This unit must be grounded to operate properly. It must be connected to a grounded metal, permanent
wiring system or an equipment-grounding conductor must be run with the circuit conductors and connected
to the equipment-grounding terminal or lead of the appliance.
8
CONNECTING AN ELECTRIC CABLE
If the cord is not long enough, or if a hard-wire installation is needed, follow the steps below to complete the
electrical connection.
WARNING! Before working on wiring for any electrical appliance, be sure the electrical
power has been turned off at the breaker/fuse box.
1. Remove the access panel by removing the two screws on each side
of the access panel that hold the fill strips in place. Next, remove the
two screws underneath the panel that hold it against the guard plate.
After you have removed all four screws, slide the access panel down
below the two tabs at the top to remove it.
2. Remove the toe kick brackets by holding the small metal spring tab
on the outer edge of the base pan toward the outside of the machine.
Continue holding the tab as you pull straight out on the bracket. (Note:
It may be stubborn because it’s in guide slots on the base pan.) See
page 10 for instructions on how to adjust the toe kick brackets.
3. Remove the guard plate by removing the three phillips-head screws
that hold the guard plate in place, two on the upper/underneath side
and two on the front.
After the screws are removed, grip the bottom of the guard plate and
pull it toward you to remove it. You can now access the inlet valve,
electrical connection, and drain pump and hose.
4. Remove the supplied power cord.
5. Connect supply cable with a UL-listed strain relief bushing (if
nonmetallic cable is to be used).
6. Connect branch circuit white lead to white lead on
main terminal block, as illustrated at right.
7. Connect branch circuit black lead to brown lead on
main terminal block, as illustrated.
8. Connect ground wire to ground on terminal block,
as illustrated.
9. Replace the guard plate.
10. Replace the toe kick brackets and toe kick (see page 9).
Toe kick bracket
Making the Connection
TESTING FOR LEAKS
1. Turn on the water supply and check for leaks.
2. Turn the power on at breaker/fuse box and test the dishwasher operation by running a Rinse cycle. (This
should take about four minutes.)
3. Turn off the electrical power and check for leaks under the dishwasher and sink.
4. Make sure that no kinks have developed in the drain lines.
If there are no leaks and the dishwasher seems to be working properly, continue with the installation.
9
FITTING THE EDW194E ONE-PIECE CUSTOM DOOR PANEL
Model EDW194E can only be installed with a one-piece custom door
panel that extends from the toe kick to the counter top. The unit comes
with everything needed to make installing the door panel easy. The
door is predrilled for the panel’s mounting screws.
To order a one-piece door, contact your dealer. The part numbers are
listed below:
White
720356200
Black
720356300
Bisque
720356400
Stainless Steel
720356500
ITEMS PROVIDED WITH THE ONE-PIECE DOOR PANELS
These items are supplied with the doors:
♦ One-piece door
♦ Color-coordinated toe kick
♦ Door handle
♦ Handle support bracket
♦ Two 1/2” machine screws for handle
♦ Two 1/2” sheet metal screws for toe kick
INSTALLING THE ONE-PIECE CUSTOM DOOR PANEL
Before fitting the custom panel, the dishwasher must be installed underneath the cabinet.
For this installation, we recommend that you install the 2” fill strip (see page 6) that comes with the unit to hide
the top of the dishwasher and further reduce water noise.
NOTE: Do not fasten the dishwasher to the cabinet until after you have installed the door panel.
1.
Remove the custom panel and parts from the packaging.
2.
Move the insulation on the back of the custom panel.
3.
Slide the handle support bracket to the inside top of the panel.
4.
Insert the screws through the support bracket and the panel.
5.
Fit the door handle to the screws and secure tightly.
6.
Remove the rubber gaskets from inside the dishwasher door and discard.
7.
Remove the second and fourth screws from the inside top of the
dishwasher door (as illustrated) and discard.
8.
With the door slightly open, position the panel with the holes in
alignment with the door holes and secure it in place with 2-12”
squeeze clamps on both sides.
9.
Insert the 1-1/2” screws partially through the dishwasher door.
10. Loosen the clamp on one side enough to align the screws with
the holes in the panel.
11. Secure the screws.
2nd
screw
Dishwasher door
4th
screw
12. Repeat steps 9 and 10 for the other side.
13. Close the door and, if necessary, adjust for square by adjusting
the front levelling legs for proper height clearance.
14. Fasten the dishwasher to the cabinet (see page 9).
10
With this
installation, the
custom panel
extends 1-13/16”
inches above the
dishwasher
control panel, as
illustrated.
BUILDING A CUSTOM WOOD DOOR PANEL FOR MODEL EDW194E
If you prefer, you can build a custom wood door panel for this model to match the cabinets.
CUSTOM WOOD PANEL DIMENSIONS
Width:
Height:
23-3/8” (595 mm)
28-1/4 min. to 30-1/16” max.
(718 mm–764 mm)
(Measured from the top of the panel to the lower edge of the kitchen cabinet.)
Thickness: 1/4” (6 mm) minimum to 3/4” (19 mm) maximum
Weight:
Up to 22 lb.
NOTE: Screws for mounting custom wood panels less than 3/4” are not supplied with the unit.
MOISTURE BARRIER
Among the materials supplied with your unit are two strips of moisture resistant material (moisture barriers).
One of these is intended to be affixed along the bottom edge of the back of the wood panel to prevent
possible moisture damage. You should affix the moisture barrier to the panel before you attach the panel to
the dishwasher door.
CUSTOM WOOD PANELS THAT EXTEND TO THE CABINET TOP (30-1/16”)
With this installation, the custom panel extends 1-13/16” inches above the dishwasher
control panel, as illustrated at right.
This installation also leaves a 2” gap between the top of the dishwasher and the
cabinet. We recommend that you install the 2” fill strip that comes with the unit
between the upper edge of the dishwasher and the counter to hide the top of the
dishwasher and further reduce water noise.
Panel extends from toe kick to cabinet top
30-1/16"
764 mm
2-inch fill strip
23-3/8"
595 mm
toe kick
toe kick
NOTE: You will also need to build a custom wood toe kick to match the wood door panel.
11
WOOD PANELS THE SAME HEIGHT AS THE DISHWASHER DOOR (23-1/4”)
Custom-built 2-inch decorative fill strip or
cutting board (not available to order)
28-1/4"
718 mm
If the custom panel is the same height as the dishwasher door,
a 2” decorative fill strip or pull-out cutting board must be used
to fill the area between the panel and the counter top (as
illustrated at right).
23-3/8"
595 mm
toe kick
INSTALLING A CUSTOM WOOD PANEL
To install the custom wood panel, follow the steps below.
1. Attach the handle (A) to the wood panel. (It is best to
use a handle instead of a knob.)
2. Remove the second and fourth screws (B and C) from
the inside top of the dishwasher door and discard.
3. With the door slightly open, position the wood panel
with the holes in alignment with the door and secure it
in place with 2-12” squeeze clamps on both sides.
4. If you are installing a 30-1/16” high panel, it should
extend 1-13/16” above the control panel. It’s a good
idea to take this measurement before you proceed.
5. Insert the 1-1/2” screws supplied with the unit through
the panel and door.
6. Secure the screws.
7. Close the door and, if necessary, adjust level by
adjusting the front levelling legs for proper height
clearance.
8. Fasten the dishwasher to the cabinet (see page 9).
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement