APC SURT192XLBP User manual

APC SURT192XLBP User manual
User Manual
English
SURT192XLBP External Battery Pack
For Use With Smart-UPS® RT 3000/5000/7500/10000 VA
Uninterruptible Power Supply
990-1387 03/2003
Introduction
The SURT192XLBP connects to the APC Smart-UPS® RT 3000/5000/7500/10000 VA. Together
these units provide extended protection from blackouts, brownouts, sags, and surges for your
computer and other critical electronic equipment.
1:
INSTALLATION
Refer to the Safety Instruction sheet included with the UPS before installing the batteries.
Unpacking
Inspect the unit upon receipt. Notify the carrier and dealer if there is damage.
The packaging is recyclable; save it for reuse or dispose of it properly.
Check the package contents:
the external battery pack
the front bezel
two tie brackets and 4 screws
product documentation, Safety Guide, warranty information
Placement of the External Battery Pack
Place the external battery pack where it will be used.
The unit is heavy. Select a location sturdy
enough to handle the weight.
Do not operate this unit where there is excessive dust or the temperature and humidity are outside the
specified limits. Refer to the APC web site, www.apc.com for details.
Ensure the air vents on the front and rear of the unit are not blocked.
PLACEMENT
1
Installing the External Battery Pack(s)
Your UPS model may vary from the model depicted in the diagram. The battery installation
procedure is identical for all models.
Prior to connecting the batteries, and tie brackets
(when used), remove the feet (if installed), from
the bottom of the UPS. See diagram.
x4
x4
REMOVING BATTERIES FROM THE EXTERNAL BATTERY PACK
This unit is heavy. To lighten the unit, remove the batteries. Refer to the unpacking instructions on
the carton the unit is shipped in or see instructions below.
1
x9
2
3
4
2
TOWER CONFIGURATION
Installing and Connecting the External Battery Pack(s)
NOTE: The external battery packs must be installed to the left of the UPS when facing the
rear of the units, (see diagrams below).
1.
Install the tie brackets (screws included), as shown in the diagrams below.
UPS and One External Battery Pack
Secure tie
brackets
2.
UPS and Two External Battery Packs
Note: Tie brackets on
the center XLBP share
a common screw.
Connect the green/yellow ground wires (screws included), as shown in the diagrams below.
TVSS Ground Wire Connections
3.
Connect the rear panel batteries as shown in the diagrams below.
Rear Battery Connections
3
Installing and Connecting the Front Batteries and Attaching the Bezel
4
3
2
1
x9
4
RACK MOUNT CONFIGURATION
Refer to the Installation Guide included in Rail Kit SURTRK2 for instructions on mounting the UPS
and the external battery packs into a rack.
NOTE: The external battery packs must be mounted below the UPS in the rack.
Installing and Connecting the External Battery Pack(s)
1.
Connect the green/yellow ground wires (screws included), as shown in the diagrams below.
TVSS Ground Wire Connections
2.
Connect the rear panel batteries as shown in the diagrams below.
Battery Connections
5
Installing and Connecting the Front Batteries and Attaching the Bezel
1
2
3
4
x9
6
Setting the UPS to Recognize the Battery Pack(s)
This configuration affects the accuracy of the runtime calculations that the UPS performs
while running on battery power.
Settings are made through supplied PowerChute® Business Edition, or PowerChute® Network
Shutdown software, optional Smart Slot accessory cards, or Terminal Mode.
Refer to the instructions included with the software or accessory cards. See Terminal Mode
instructions below.
TERMINAL MODE FOR 3000 VA MODELS
Terminal Mode is a menu driven interface that enables enhanced configuration of the UPS.
Connect the serial cable to the serial com connector on the back of the UPS.
USING TERMINAL MODE PROGRAM WITH WINDOWS 2000 TO SET NUMBER OF BATTERY PACKS
1.
2.
3.
4.
5.
Exit PowerChute® Business Edition software. Follow these steps:
•
From the Desktop, go to Start => Settings => Control Panel => Administrative Tools =>
Services.
•
Select APC PCBE Server and APC PCBE Agent – right click the mouse and select Stop.
Open a terminal program. Example: HyperTerminal
•
From the Desktop, go to Start => Programs => Accessories => Communication
=>HyperTerminal.
Double-click on the HyperTerminal icon.
•
Follow the prompts to choose a name and select an icon. Disregard the message, “...must
install a modem,” if it is displayed. Click OK.
•
Select the COM port that is connected to your UPS. The port settings are:
bits per second - 2400
data - bits 8
parity - none
stop bit - 1
flow control - none
•
Click Enter
Once the blank terminal window is open, follow these steps to enter the number of battery packs:
•
Press Enter to initiate terminal mode. Follow the prompts:
•
Press 1 to modify UPS Settings. Press e (or E) to modify the number of battery
packs. Enter the number of battery packs, including the internal battery pack.
Press Enter.
•
Follow the prompts.
Exit the terminal program.
7
TERMINAL MODE FOR 5000/7500/10000 VA MODELS
When using PowerChute® Network Shutdown software:
1.
2.
3.
Open a terminal program. Example: HyperTerminal
•
From the Desktop, go to Start => Programs => Accessories => Communication
=>HyperTerminal.
Double-click on the HyperTerminal icon.
•
Follow the prompts to choose a name and select an icon. Disregard the message, “...must
install a modem,” if it is displayed. Click OK.
•
Select the COM port that is connected to your UPS. The port settings are:
bits per second - 2400
data - bits 8
parity - none
stop bit - 1
flow control - none
•
Click Enter
Once the blank terminal window is open, follow these steps to enter the number of battery packs:
•
Press ENTER to initiate terminal mode. Press ENTER multiple times, until the prompt User
Name: is displayed. Follow the prompts. Type slowly, waiting until each character appears
on the screen prior to typing the next character.
•
•
User Name: apc
•
Password:
apc
Press 1 and ENTER to select Device Manager.
•
Select the model by entering the corresponding number, then press ENTER.
•
Press 3 and ENTER to select Configuration.
•
Press 1 and ENTER to select Battery.
•
Press 2 and ENTER to change the Battery Settings.
•
Type in the number of external battery packs, then press ENTER.
•
Press 3 and ENTER to accept the changes.
•
Press ESC multiple times (5) to return to the main menu.
•
Press 4 and ENTER to log out.
8
4: STORAGE, MAINTENANCE, AND SERVICE
Storage
Store the UPS covered and positioned as for proper functioning, in a cool, dry location, with the
batteries fully charged.
Store at: 50,000 ft (15,000 m)
-4° to 140° F (-20 to 60 ° C) Charge the batteries every 6 months.
Replacing the Battery Module
This UPS has an easy to replace, hot-swappable battery module. Replacement is a safe procedure,
isolated from electrical hazards. You may leave the UPS and connected equipment on during the
procedure. See your dealer or contact APC at the web site, www.apc.com for information on RBC44
replacement battery modules.
The UPS battery life differs based on usage and environment. Refer to www.apc.com for on battery
runtimes.
Service
If the UPS requires service follow these steps:
1.
2.
Contact APC Customer Service through the APC web site, www.apc.com/support.
Note the model number of the unit, the serial number, and the date purchased. If you call
APC Customer Service, a technician will ask you to describe the problem and try to solve it
over the phone, if possible. If this is not possible, the technician will issue a Returned
Material Authorization Number (RMA#).
If the unit is under warranty, repairs are free. If not, there is a repair charge.
Pack the unit in its original packaging. If the original packing is not available, refer to the APC
web site, www.apc.com/support, for information about obtaining a new set.
Pack the unit properly to avoid damage in transit. Never use Styrofoam beads for packaging.
Damage sustained in transit is not covered under warranty.
Always DISCONNECT THE BATTERY(S) before shipping in compliance with
U.S. Department of Transportation (DOT) regulations.
The battery(s) may remain in the UPS.
3.
Mark the RMA# on the outside of the package.
4.
Return the unit by insured, prepaid carrier to the address given to you by Customer Service.
Contacting APC
In the USA …
Outside the USA …
Refer to the APC web site,
www.apc.com/support.
Refer to the APC web site, www.apc.com. Select the appropriate
country from the country selection field. Select the Support tab at the
top of the web page.
9
5: REGULATORY AND WARRANTY INFORMATION
Regulatory Agency Approvals
See User Manuals for SURT3000/5000XL 3U and SURT7500/10000XL 6U models for complete
regulatory approval listings.
Declaration of Conformity
Limited Warranty
American Power Conversion (APC) warrants its products to be free from defects in materials and workmanship for a period of
two years from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its own sole
option, any such defective products. To obtain service under warranty you must obtain a Returned Material Authorization
(RMA) number from customer support. Products must be returned with transportation charges prepaid and must be
accompanied by a brief description of the problem encountered and proof of date and place of purchase. This warranty does
not apply to equipment that has been damaged by accident, negligence, or misapplication or has been altered or modified in
any way. This warranty applies only to the original purchaser who must have properly registered the product within 10 days of
purchase.
EXCEPT AS PROVIDED HEREIN, AMERICAN POWER CONVERSION MAKES NO WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s)
may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL APC BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, APC is not liable for any costs, such as lost profits or
revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties,
or otherwise.
Entire contents copyright © 2003 by American Power Conversion Corporation. All rights reserved. Reproduction in whole or in part without permission is prohibited.
APC, Smart-UPS, and PowerChute are registered trademarks of American Power Conversion Corporation. All other trademarks are the property of their respective
owners.
10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement